SN74LVC2T45 DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES516I - DECEMBER 2003 - REVISED MARCH 2007 FEATURES * * * * * * * * * * Available in the Texas Instruments NanoFreeTM Package Fully Configurable Dual-Rail Design Allows Each Port to Operate Over the Full 1.65-V to 5.5-V Power-Supply Range VCC Isolation Feature - If Either VCC Input Is at GND, Both Ports Are in the High-Impedance State DIR Input Circuit Referenced to VCCA Low Power Consumption, 10-A Max ICC 24-mA Output Drive at 3.3 V Ioff Supports Partial-Power-Down Mode Operation Max Data Rates - 420 Mbps (3.3-V to 5-V Translation) - 210 Mbps (Translate to 3.3 V) - 140 Mbps (Translate to 2.5 V) - 75 Mbps (Translate to 1.8 V) Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II ESD Protection Exceeds JESD 22 - 4000-V Human-Body Model (A114-A) - 200-V Machine Model (A115-A) - 1000-V Charged-Device Model (C101) DCT OR DCU PACKAGE (TOP VIEW) VCCA A1 A2 GND 1 8 2 7 3 6 4 5 VCCB B1 B2 DIR YZP PACKAGE (BOTTOM VIEW) GND D1 4 5 D2 A2 A1 C1 3 6 C2 B1 2 7 B2 VCCA A1 1 8 A2 DIR B2 B1 VCCB DESCRIPTION/ORDERING INFORMATION This dual-bit noninverting bus transceiver uses two separate configurable power-supply rails. The A port is designed to track VCCA. VCCA accepts any supply voltage from 1.65 V to 5.5 V. The B port is designed to track VCCB. VCCB accepts any supply voltage from 1.65 V to 5.5 V. This allows for universal low-voltage bidirectional translation between any of the 1.8-V, 2.5-V, 3.3-V, and 5-V voltage nodes. ORDERING INFORMATION PACKAGE (1) TA NanoFree - WCSP (DSBGA) 0.23-mm Large Bump - YZP (Pb-free) -40C to 85C SSOP - DCT VSSOP - DCU (1) (2) ORDERABLE PART NUMBER Reel of 3000 SN74LVC2T45YZPR Reel of 3000 SN74LVC2T45DCTR Reel of 250 SN74LVC2T45DCTT Reel of 3000 SN74LVC2T45DCUR Reel of 250 SN74LVC2T45DCUT TOP-SIDE MARKING (2) _ _ _TB_ CT2_ _ _ CT2_ For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. DCT: The actual top-side marking has three additional characters that designate the year, month, and assembly/test site. DCU: The actual top-side marking has one additional character that designates the assembly/test site. YZP: The actual top-side marking has three preceding characters to denote year, month, and sequence code, and one following character to designate the assembly/test site. Pin 1 identifier indicates solder-bump composition (1 = SnPb, * = Pb-free). Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. NanoFree is a trademark of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2003-2007, Texas Instruments Incorporated SN74LVC2T45 DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES516I - DECEMBER 2003 - REVISED MARCH 2007 DESCRIPTION/ORDERING INFORMATION (CONTINUED) The SN74LVC2T45 is designed for asynchronous communication between two data buses. The logic levels of the direction-control (DIR) input activate either the B-port outputs or the A-port outputs. The device transmits data from the A bus to the B bus when the B-port outputs are activated, and from the B bus to the A bus when the A-port outputs are activated. The input circuitry on both A and B ports always is active and must have a logic HIGH or LOW level applied to prevent excess ICC and ICCZ. The SN74LVC2T45 is designed so that the DIR input circuit is supplied by VCCA. This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down. The VCC isolation feature ensures that if either VCC input is at GND, both ports are in the high-impedance state. NanoFreeTM package technology is a major breakthrough in IC packaging concepts, using the die as the package. FUNCTION TABLE (1) (EACH TRANSCEIVER) (1) INPUT DIR OPERATION L B data to A bus H A data to B bus Input circuits of the data I/Os always are active. LOGIC DIAGRAM (POSITIVE LOGIC) DIR A1 5 2 7 A2 3 6 VCCA 2 B1 Submit Documentation Feedback VCCB B2 SN74LVC2T45 DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES516I - DECEMBER 2003 - REVISED MARCH 2007 Absolute Maximum Ratings (1) over operating free-air temperature range (unless otherwise noted) MIN MAX Supply voltage range -0.5 6.5 V VI Input voltage range (2) -0.5 6.5 V VO Voltage range applied to any output in the high-impedance or power-off state (2) -0.5 6.5 V A port -0.5 VCCA + 0.5 B port -0.5 VCCB + 0.5 VCCA VCCB UNIT VO Voltage range applied to any output in the high or low state (2) (3) IIK Input clamp current VI < 0 -50 mA IOK Output clamp current VO < 0 -50 mA IO Continuous output current 50 mA 100 mA Continuous current through VCC or GND JA Package thermal impedance (4) Tstg Storage temperature range DCT package 220 DCU package 227 YZP package (1) (2) (3) (4) V C/W 102 -65 150 C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. The value of VCC is provided in the recommended operating conditions table. The package thermal impedance is calculated in accordance with JESD 51-7. Submit Documentation Feedback 3 SN74LVC2T45 DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES516I - DECEMBER 2003 - REVISED MARCH 2007 Recommended Operating Conditions (1) (2) (3) VCCI VCCA VCCB VCCO Supply voltage High-level input voltage 2.3 V to 2.7 V Data inputs (4) MAX 1.65 5.5 1.65 5.5 1.7 3 V to 3.6 V VCCI x 0.7 VCCI x 0.35 1.65 V to 1.95 V VIL Data inputs (4) 2.3 V to 2.7 V 0.7 3 V to 3.6 V 0.8 VCCA x 0.65 1.65 V to 1.95 V High-level input voltage DIR (referenced to VCCA) (5) 2.3 V to 2.7 V 1.7 3 V to 3.6 V VCCA x 0.7 4.5 V to 5.5 V VCCA x 0.35 2.3 V to 2.7 V 0.7 3 V to 3.6 V 0.8 VIL Low-level input voltage VI Input voltage 0 5.5 V VO Output voltage 0 VCCO V 1.65 V to 1.95 V IOH High-level output current IOL Low-level output current t/v Input transition rise or fall rate Data inputs Control input TA (1) (2) (3) (4) (5) V VCCA x 0.3 4.5 V to 5.5 V 4 V 2 1.65 V to 1.95 V DIR (referenced to VCCA) (5) V VCCI x 0.3 4.5 V to 5.5 V VIH V V 2 4.5 V to 5.5 V Low-level input voltage UNIT VCCI x 0.65 1.65 V to 1.95 V VIH MIN -4 2.3 V to 2.7 V -8 3 V to 3.6 V -24 4.5 V to 5.5 V -32 1.65 V to 1.95 V 4 2.3 V to 2.7 V 8 3 V to 3.6 V 24 4.5 V to 5.5 V 32 1.65 V to 1.95 V 20 2.3 V to 2.7 V 20 3 V to 3.6 V 10 4.5 V to 5.5 V 5 1.65 V to 5.5 V 5 Operating free-air temperature -40 85 mA mA ns/V C VCCI is the VCC associated with the input port. VCCO is the VCC associated with the output port. All unused data inputs of the device must be held at VCCI or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. For VCCI values not specified in the data sheet, VIH min = VCCI x 0.7 V, VIL max = VCCI x 0.3 V. For VCCI values not specified in the data sheet, VIH min = VCCA x 0.7 V, VIL max = VCCA x 0.3 V. Submit Documentation Feedback SN74LVC2T45 DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES516I - DECEMBER 2003 - REVISED MARCH 2007 Electrical Characteristics (1) (2) over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS IOH = -100 A IOH = -8 mA 1.65 V to 4.5 V 1.65 V to 4.5 V 1.65 V 1.65 V 1.2 2.3 V 2.3 V 1.9 3V 3V 2.4 3.8 VI = VIH IOH = -24 mA A port B port A or B port IOZ ICCA 0.1 1.65 V 0.45 2.3 V 2.3 V 0.3 3V 3V 0.55 VI = VCCA or GND VO = VCCO or GND VI = VCCI or GND, IO = 0 One A port at VCCA - 0.6 V, DIR at VCCA, B port = open DIR DIR at VCCA - 0.6 V, B port = open, A port at VCCA or GND ICCB B port One B port at VCCB - 0.6 V, DIR at GND, A port = open CI DIR Cio A or B port (1) (2) 4.5 V 4.5 V 1.65 V to 5.5 V 1.65 V to 5.5 V 1 2 V 0.55 0V 0 to 5.5 V 1 2 0 to 5.5 V 0V 1 2 1.65 V to 5.5 V 1.65 V to 5.5 V 1 2 1.65 V to 5.5 V 1.65 V to 5.5 V 5V 0V 2 0V 5V -2 1.65 V to 5.5 V 1.65 V to 5.5 V 3 5V 0V -2 0V 5V 2 1.65 V to 5.5 V 1.65 V to 5.5 V 4 VI or VO = 0 to 5.5 V A port ICCA V 1.65 V VI = VIL UNIT VCCO - 0.1 4.5 V VI = VCCI or GND, IO = 0 ICCA + ICCB (see Table 1) MAX 1.65 V to 4.5 V VI = VCCI or GND, IO = 0 ICCB MIN 4.5 V IOL = 32 mA Ioff MAX 1.65 V to 4.5 V IOL = 24 mA DIR TYP IOL = 100 A IOL = 8 mA II MIN IOH = -32 mA IOL = 4 mA VOL -40C to 85C VCCB IOH = -4 mA VOH TA = 25C VCCA A A A 3 A A A 50 3 V to 5.5 V A 3 V to 5.5 V 50 50 A 3 V to 5.5 V 3 V to 5.5 V VI = VCCA or GND 3.3 V 3.3 V 2.5 pF VO = VCCA/B or GND 3.3 V 3.3 V 6 pF VCCO is the VCC associated with the output port. VCCI is the VCC associated with the input port. Submit Documentation Feedback 5 SN74LVC2T45 DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES516I - DECEMBER 2003 - REVISED MARCH 2007 Switching Characteristics over recommended operating free-air temperature range, VCCA = 1.8 V 0.15 V (unless otherwise noted) (see Figure 1) PARAMETER tPLH tPHL tPLH tPHL tPHZ tPLZ tPHZ tPLZ tPZH (1) tPZL (1) tPZH (1) tPZL (1) (1) FROM (INPUT) TO (OUTPUT) A B B A DIR A DIR B DIR A DIR B VCCB = 1.8 V 0.15 V VCCB = 2.5 V 0.2 V VCCB = 3.3 V 0.3 V VCCB = 5 V 0.5 V UNIT MIN MAX MIN MAX MIN MAX MIN MAX 3 17.7 2.2 10.3 1.7 8.3 1.4 7.2 2.8 14.3 2.2 8.5 1.8 7.1 1.7 7 3 17.7 2.3 16 2.1 15.5 1.9 15.1 2.8 14.3 2.1 12.9 2 12.6 1.8 12.2 10.6 30.9 10.3 30.5 10.5 30.5 10.7 29.3 7.3 19.7 7.5 19.6 7.5 19.5 7 19.4 10 27.9 8.4 14.9 6.5 11.3 4.1 8.6 6.5 19.5 7.2 12.6 4.3 9.7 2.1 7.1 37.2 28.6 25.2 22.2 42.2 27.8 23.9 20.8 37.4 29.9 27.8 26.6 45.2 39 37.6 36.3 ns ns ns ns ns ns The enable time is a calculated value, derived using the formula shown in the enable times section. Switching Characteristics over recommended operating free-air temperature range, VCCA = 2.5 V 0.2 V (unless otherwise noted) (see Figure 1) PARAMETER tPLH tPHL tPLH tPHL tPHZ tPLZ tPHZ tPLZ tPZH (1) tPZL (1) tPZH (1) tPZL (1) 6 (1) FROM (INPUT) TO (OUTPUT) A B B A DIR A DIR B DIR A DIR B VCCB = 1.8 V 0.15 V VCCB = 2.5 V 0.2 V VCCB = 3.3 V 0.3 V VCCB = 5 V 0.5 V UNIT MIN MAX MIN MAX MIN MAX MIN MAX 2.3 16 1.5 8.5 1.3 6.4 1.1 5.1 2.1 12.9 1.4 7.5 1.3 5.4 0.9 4.6 2.2 10.3 1.5 8.5 1.4 8 1 7.5 2.2 8.5 1.4 7.5 1.3 7 0.9 6.2 6.6 17.1 7.1 16.8 6.8 16.8 5.2 16.5 5.3 12.6 5.2 12.5 4.9 12.3 4.8 12.3 10.7 27.9 8.1 13.9 5.8 10.5 3.5 7.6 7.8 18.9 6.2 11.2 3.6 8.9 1.4 6.2 29.2 19.7 16.9 13.7 36.4 21.4 17.5 13.8 28.6 21 18.7 17.4 30 24.3 22.2 21.1 The enable time is a calculated value, derived using the formula shown in the enable times section. Submit Documentation Feedback ns ns ns ns ns ns SN74LVC2T45 DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES516I - DECEMBER 2003 - REVISED MARCH 2007 Switching Characteristics over recommended operating free-air temperature range, VCCA = 3.3 V 0.3 V (unless otherwise noted) (see Figure 1) PARAMETER tPLH tPHL tPLH tPHL tPHZ tPLZ tPHZ tPLZ tPZH (1) tPZL (1) tPZH (1) tPZL (1) (1) FROM (INPUT) TO (OUTPUT) A B B A DIR A DIR B DIR A DIR B VCCB = 1.8 V 0.15 V VCCB = 2.5 V 0.2 V VCCB = 3.3 V 0.3 V VCCB = 5 V 0.5 V UNIT MIN MAX MIN MAX MIN MAX MIN MAX 2.1 15.5 1.4 8 0.7 5.6 0.7 4.4 2 12.6 1.3 7 0.8 5 0.7 4 1.7 8.3 1.3 6.4 0.7 5.8 0.6 5.4 1.8 7.1 1.3 5.4 0.8 5 0.7 4.5 5 10.9 5.1 10.8 5 10.8 5 10.4 3.4 8.4 3.7 8.4 3.9 8.1 3.3 7.8 11.2 27.3 8 13.7 5.8 10.4 2.9 7.4 9.4 17.7 5.6 11.3 4.3 8.3 1 5.6 26 17.7 14.1 11 34.4 19.1 15.4 11.9 23.9 16.4 13.9 12.2 23.5 17.8 15.8 14.4 ns ns ns ns ns ns The enable time is a calculated value, derived using the formula shown in the enable times section. Switching Characteristics over recommended operating free-air temperature range, VCCA = 5 V 0.5 V (unless otherwise noted) (see Figure 1) PARAMETER tPLH tPHL tPLH tPHL tPHZ tPLZ tPHZ tPLZ tPZH (1) tPZL (1) tPZH (1) tPZL (1) (1) FROM (INPUT) TO (OUTPUT) A B B A DIR A DIR B DIR A DIR B VCCB = 1.8 V 0.15 V VCCB = 2.5 V 0.2 V VCCB = 3.3 V 0.3 V VCCB = 5 V 0.5 V UNIT MIN MAX MIN MAX MIN MAX MIN MAX 1.9 15.1 1 7.5 0.6 5.4 0.5 3.9 1.8 12.2 0.9 6.2 0.7 4.5 0.5 3.5 1.4 7.2 1 5.1 0.7 4.4 0.5 3.9 1.7 7 0.9 4.6 0.7 4 0.5 3.5 2.9 8.2 2.9 7.9 2.8 7.9 2.2 7.8 1.4 6.9 1.3 6.7 0.7 6.7 0.7 6.6 11.2 26.1 7.2 13.9 5.8 10.1 1.3 7.3 8.4 16.9 5 11 4 7.7 1 5.6 24.1 16.1 12.1 9.5 33.1 18.5 14.1 10.8 22 14.2 12.1 10.5 20.4 14.1 12.4 11.3 ns ns ns ns ns ns The enable time is a calculated value, derived using the formula shown in the enable times section. Submit Documentation Feedback 7 SN74LVC2T45 DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES516I - DECEMBER 2003 - REVISED MARCH 2007 Operating Characteristics TA = 25C PARAMETER CpdA CpdB (1) 8 (1) A-port input, B-port output B-port input, A-port output (1) A-port input, B-port output B-port input, A-port output TEST CONDITIONS CL = 0 pF, f = 10 MHz, tr = tf = 1 ns CL = 0 pF, f = 10 MHz, tr = tf = 1 ns VCCA = VCCB = 1.8 V VCCA = VCCB = 2.5 V VCCA = VCCB = 3.3 V VCCA = VCCB = 5 V TYP TYP TYP TYP 3 4 4 4 18 19 20 21 18 19 20 21 3 4 4 4 UNIT pF pF Power dissipation capacitance per transceiver Submit Documentation Feedback SN74LVC2T45 DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES516I - DECEMBER 2003 - REVISED MARCH 2007 Power-Up Considerations A proper power-up sequence always should be followed to avoid excessive supply current, bus contention, oscillations, or other anomalies. To guard against such power-up problems, take the following precautions: 1. Connect ground before any supply voltage is applied. 2. Power up VCCA. 3. VCCB can be ramped up along with or after VCCA. Table 1. Typical Total Static Power Consumption (ICCA + ICCB) VCCB VCCA 0V 1.8 V 2.5 V 3.3 V 5V <1 0V 0 <1 <1 <1 1.8 V <1 <2 <2 <2 2 2.5 V <1 <2 <2 <2 <2 3.3 V <1 <2 <2 <2 <2 5V <1 2 <2 <2 <2 Submit Documentation Feedback UNIT A 9 SN74LVC2T45 DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES516I - DECEMBER 2003 - REVISED MARCH 2007 TYPICAL CHARACTERISTICS abc TYPICAL PROPAGATION DELAY (A to B) vs LOAD CAPACITANCE TA = 25C, VCCA = 1.8 V 10 10 9 9 VCCB = 1.8 V 8 8 7 7 6 6 t PLH- ns t PHL - ns VCCB = 1.8 V VCCB = 2.5 V 5 VCCB = 2.5 V 5 VCCB = 3.3 V 4 4 VCCB = 5 V VCCB = 3.3 V 3 3 VCCB = 5 V 2 2 1 1 0 0 0 5 10 15 20 25 30 0 35 5 10 15 20 25 30 35 CL - pF CL - pF TYPICAL PROPAGATION DELAY (B to A) vs LOAD CAPACITANCE TA = 25C, VCCA = 1.8 V 10 10 9 9 8 VCCB = 1.8 V 8 VCCB = 2.5 V 7 7 6 6 5 VCCB = 2.5 V VCCB = 3.3 V 4 VCCB = 5 V t PLH - ns t PHL - ns VCCB = 1.8 V VCCB = 3.3 V VCCB = 5 V 5 4 3 3 2 2 1 1 0 0 0 5 10 15 20 25 30 35 0 5 CL - pF 10 Submit Documentation Feedback 10 15 20 CL - pF 25 30 35 SN74LVC2T45 DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES516I - DECEMBER 2003 - REVISED MARCH 2007 TYPICAL CHARACTERISTICS abc TYPICAL PROPAGATION DELAY (A to B) vs LOAD CAPACITANCE TA = 25C, VCCA = 2.5 V 10 10 9 9 8 8 7 VCCB = 1.8 V 6 t PLH - ns t PHL - ns 7 VCCB = 1.8 V 6 5 VCCB = 2.5 V 4 4 VCCB = 3.3 V 3 3 VCCB = 5 V 5 VCCB = 2.5 V VCCB = 3.3 V 2 2 VCCB = 5 V 1 1 0 0 0 10 5 15 20 25 30 0 35 10 5 15 20 25 30 35 CL - pF CL - pF 10 10 9 9 8 8 7 7 6 6 t PLH - ns t PHL - ns TYPICAL PROPAGATION DELAY (B to A) vs LOAD CAPACITANCE TA = 25C, VCCA = 2.5 V VCCB = 1.8 V 5 4 5 4 3 VCCB = 3.3 V VCCB = 5 V 2 VCCB = 2.5 V VCCB = 3.3 V 3 VCCB = 2.5 V VCCB = 5 V 2 1 0 VCCB = 1.8 V 1 0 5 10 15 20 CL - pF 25 30 35 0 0 5 10 15 20 25 30 35 CL - pF Submit Documentation Feedback 11 SN74LVC2T45 DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES516I - DECEMBER 2003 - REVISED MARCH 2007 TYPICAL CHARACTERISTICS abc TYPICAL PROPAGATION DELAY (A to B) vs LOAD CAPACITANCE TA = 25C, VCCA = 3.3 V 10 10 9 9 8 8 7 7 VCCB = 1.8 V 6 6 t PLH - ns t PHL - ns VCCB = 1.8 V 5 VCCB = 2.5 V 4 3 VCCB = 2.5 V 5 4 VCCB = 3.3 V 3 VCCB = 5 V 2 2 VCCB = 3.3 V 1 1 VCCB = 5 V 0 0 0 5 10 15 20 25 30 0 35 5 10 15 20 25 30 35 CL - pF CL - pF 10 10 9 9 8 8 7 7 6 6 t PLH - ns t PHL - ns TYPICAL PROPAGATION DELAY (B to A) vs LOAD CAPACITANCE TA = 25C, VCCA = 3.3 V 5 VCCB = 1.8 V 4 3 VCCB = 1.8 V 5 4 3 2 VCCB = 3.3 V VCCB = 3.3 V 1 VCCB = 2.5 V 2 VCCB = 2.5 V 1 VCCB = 5 V 0 VCCB = 5 V 0 0 5 10 15 20 25 30 35 0 5 12 10 15 CL - pF CL - pF Submit Documentation Feedback 20 25 30 35 SN74LVC2T45 DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES516I - DECEMBER 2003 - REVISED MARCH 2007 TYPICAL CHARACTERISTICS abc TYPICAL PROPAGATION DELAY (A to B) vs LOAD CAPACITANCE TA = 25C, VCCA = 5 V 10 10 9 9 8 8 7 7 VCCB = 1.8 V VCCB = 1.8 V t PLH - ns t PHL - ns 6 5 4 6 5 VCCB = 2.5 V 4 VCCB = 2.5 V VCCB = 3.3 V 3 3 2 2 VCCB = 5 V VCCB = 3.3 V 1 0 1 VCCB = 5 V 0 0 5 10 15 20 25 30 35 0 5 10 CL - pF 15 20 25 30 35 25 30 35 CL - pF 10 10 9 9 8 8 7 7 6 6 t PLH - ns t PHL- ns TYPICAL PROPAGATION DELAY (B to A) vs LOAD CAPACITANCE TA = 25C, VCCA = 5 V 5 4 VCCB = 1.8 V 3 VCCB = 2.5 V 5 VCCB = 1.8 V 4 VCCB = 2.5 V 3 2 2 VCCB = 3.3 V VCCB = 3.3 V VCCB = 5 V 1 0 0 5 10 VCCB = 5 V 1 15 20 25 30 35 0 0 5 CL - pF 10 15 20 CL - pF Submit Documentation Feedback 13 SN74LVC2T45 DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES516I - DECEMBER 2003 - REVISED MARCH 2007 PARAMETER MEASUREMENT INFORMATION 2 x VCCO S1 RL From Output Under Test Open GND CL (see Note A) TEST S1 tpd tPLZ/tPZL tPHZ/tPZH Open 2 x VCCO GND RL tw LOAD CIRCUIT VCCI VCCI/2 Input VCCO CL RL VTP 1.8 V 0.15 V 2.5 V 0.2 V 3.3 V 0.3 V 5 V 0.5 V 15 pF 15 pF 15 pF 15 pF 2 k 2 k 2 k 2 k 0.15 V 0.15 V 0.3 V 0.3 V VCCI/2 0V VOLTAGE WAVEFORMS PULSE DURATION VCCA Output Control (low-level enabling) VCCA/2 VCCA/2 0V tPZL VCCI Input VCCI/2 VCCI/2 0V tPLH Output tPHL VOH VCCO/2 VOL VCCO/2 tPLZ VCCO Output Waveform 1 S1 at 2 x VCCO (see Note B) VCCO/2 VOL + VTP VOL tPZH Output Waveform 2 S1 at GND (see Note B) VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES tPHZ VCCO/2 VOH - VTP VOH 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR v10 MHz, ZO = 50 , dv/dt 1 V/ns. D. The outputs are measured one at a time, with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. H. VCCI is the VCC associated with the input port. I. VCCO is the VCC associated with the output port. J. All parameters and waveforms are not applicable to all devices. Figure 1. Load Circuit and Voltage Waveforms 14 Submit Documentation Feedback SN74LVC2T45 DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES516I - DECEMBER 2003 - REVISED MARCH 2007 APPLICATION INFORMATION The following shows an example of the SN74LVC2T45 being used in a unidirectional logic level-shifting application. VCC1 VCC2 VCC1 VCC2 1 8 2 7 3 6 4 5 VCC2 VCC1 SYSTEM-1 SYSTEM-2 PIN NAME FUNCTION 1 VCCA VCC1 SYSTEM-1 supply voltage (1.65 V to 5.5 V) DESCRIPTION 2 A1 OUT1 Output level depends on VCC1 voltage. 3 A2 OUT2 Output level depends on VCC1 voltage. 4 GND GND Device GND 5 DIR DIR GND (low level) determines B-port to A-port direction. 6 B2 IN2 Input threshold value depends on VCC2 voltage. 7 B1 IN1 Input threshold value depends on VCC2 voltage. 8 VCCB VCC2 SYSTEM-2 supply voltage (1.65 V to 5.5 V) Figure 2. Unidirectional Logic Level-Shifting Application Submit Documentation Feedback 15 SN74LVC2T45 DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES516I - DECEMBER 2003 - REVISED MARCH 2007 APPLICATION INFORMATION Figure 3 shows the SN74LVC2T45 being used in a bidirectional logic level-shifting application. Since the SN74LVC2T45 does not have an output-enable (OE) pin, the system designer should take precautions to avoid bus contention between SYSTEM-1 and SYSTEM-2 when changing directions. VCC1 VCC1 VCC2 Pullup/Down or Bus Hold(1) Pullup/Down or Bus Hold(1) I/O-1 VCC2 1 8 2 7 3 6 4 5 I/O-2 DIR CTRL SYSTEM-1 SYSTEM-2 The following table shows data transmission from SYSTEM-1 to SYSTEM-2 and then from SYSTEM-2 to SYSTEM-1. STATE DIR CTRL I/O-1 I/O-2 1 H Out In 2 H Hi-Z Hi-Z SYSTEM-2 is getting ready to send data to SYSTEM-1. I/O-1 and I/O-2 are disabled. The bus-line state depends on pullup or pulldown. (1) 3 L Hi-Z Hi-Z DIR bit is flipped. I/O-1 and I/O-2 still are disabled. The bus-line state depends on pullup or pulldown. (1) 4 L In Out SYSTEM-2 data to SYSTEM-1 (1) DESCRIPTION SYSTEM-1 data to SYSTEM-2 SYSTEM-1 and SYSTEM-2 must use the same conditions, i.e., both pullup or both pulldown. Figure 3. Bidirectional Logic Level-Shifting Application Enable Times Calculate the enable times for the SN74LVC2T45 using the following formulas: * tPZH (DIR to A) = tPLZ (DIR to B) + tPLH (B to A) * tPZL (DIR to A) = tPHZ (DIR to B) + tPHL (B to A) * tPZH (DIR to B) = tPLZ (DIR to A) + tPLH (A to B) * tPZL (DIR to B) = tPHZ (DIR to A) + tPHL (A to B) In a bidirectional application, these enable times provide the maximum delay from the time the DIR bit is switched until an output is expected. For example, if the SN74LVC2T45 initially is transmitting from A to B, then the DIR bit is switched; the B port of the device must be disabled before presenting it with an input. After the B port has been disabled, an input signal applied to it appears on the corresponding A port after the specified propagation delay. 16 Submit Documentation Feedback PACKAGE OPTION ADDENDUM www.ti.com 9-Mar-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp ACTIVE SM8 DCT 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LVC2T45DCTRE4 ACTIVE SM8 DCT 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LVC2T45DCTRG4 ACTIVE SM8 DCT 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LVC2T45DCTT ACTIVE SM8 DCT 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LVC2T45DCTTE4 ACTIVE SM8 DCT 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LVC2T45DCTTG4 ACTIVE SM8 DCT 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LVC2T45DCUR ACTIVE US8 DCU 8 3000 Green (RoHS & no Sb/Br) SN74LVC2T45DCURE4 ACTIVE US8 DCU 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LVC2T45DCURG4 ACTIVE US8 DCU 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LVC2T45DCUT ACTIVE US8 DCU 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LVC2T45DCUTE4 ACTIVE US8 DCU 8 SN74LVC2T45DCUTG4 ACTIVE US8 DCU 8 250 Green (RoHS & no Sb/Br) TBD SN74LVC2T45YZPR ACTIVE DSBGA YZP 8 3000 Green (RoHS & no Sb/Br) Call TI Samples (Requires Login) SN74LVC2T45DCTR CU SN (3) Level-1-260C-UNLIM Call TI CU NIPDAU Level-1-260C-UNLIM SNAGCU Level-1-260C-UNLIM (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 9-Mar-2012 TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF SN74LVC2T45 : * Automotive: SN74LVC2T45-Q1 * Enhanced Product: SN74LVC2T45-EP NOTE: Qualified Version Definitions: * Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects * Enhanced Product - Supports Defense, Aerospace and Medical Applications Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 18-Feb-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device SN74LVC2T45DCUR Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 3.35 1.05 4.0 8.0 Q3 US8 DCU 8 3000 180.0 8.4 2.25 SN74LVC2T45DCUR US8 DCU 8 3000 180.0 9.0 2.05 3.3 1.0 4.0 8.0 Q3 SN74LVC2T45YZPR DSBGA YZP 8 3000 178.0 9.2 1.02 2.02 0.63 4.0 8.0 Q1 SN74LVC2T45YZPR DSBGA YZP 8 3000 180.0 8.4 1.02 2.02 0.63 4.0 8.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 18-Feb-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN74LVC2T45DCUR US8 DCU 8 3000 202.0 201.0 28.0 SN74LVC2T45DCUR US8 DCU 8 3000 182.0 182.0 20.0 SN74LVC2T45YZPR DSBGA YZP 8 3000 220.0 220.0 35.0 SN74LVC2T45YZPR DSBGA YZP 8 3000 210.0 185.0 35.0 Pack Materials-Page 2 MECHANICAL DATA MPDS049B - MAY 1999 - REVISED OCTOBER 2002 DCT (R-PDSO-G8) PLASTIC SMALL-OUTLINE PACKAGE 0,30 0,15 0,65 8 0,13 M 5 0,15 NOM CCCCC CCCCC CCCCC CCCCC 2,90 2,70 4,25 3,75 Gage Plane PIN 1 INDEX AREA 1 0,25 4 0 - 8 3,15 2,75 0,60 0,20 1,30 MAX Seating Plane 0,10 0,10 0,00 NOTES: A. B. C. D. 4188781/C 09/02 All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion Falls within JEDEC MO-187 variation DA. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 D: Max = 1.918 mm, Min =1.858 mm E: Max = 0.918 mm, Min =0.858 mm IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated