DS90C402 DS90C402 Dual Low Voltage Differential Signaling (LVDS) Receiver Literature Number: SNLS001B DS90C402 Dual Low Voltage Differential Signaling (LVDS) Receiver General Description Features The DS90C402 is a dual receiver device optimized for high data rate and low power applications. This device along with the DS90C401 provides a pair chip solution for a dual high speed point-to-point interface. The device is in a PCB space saving 8 lead small outline package. The receiver offers 100 mV threshold sensitivity, in addition to common-mode noise protection. n n n n n n Ultra Low Power Dissipation Operates above 155.5 Mbps Standard TIA/EIA-644 8 Lead SOIC Package saves PCB space VCM 1V center around 1.2V 100 mV Receiver Sensitivity Connection Diagram 10000601 Order Number DS90C402M See NS Package Number M08A Functional Diagram 10000602 TRI-STATE (R) is a registered trademark of National Semiconductor Corporation. (c) 2005 National Semiconductor Corporation DS100006 www.national.com DS90C402 Dual Low Voltage Differential Signaling (LVDS) Receiver August 2005 DS90C402 Absolute Maximum Ratings (Note 1) Maximum Junction Temperature If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. ESD Rating (Note 4) Supply Voltage (VCC) +150C 3,500V (HBM, 1.5 k, 100 pF) (EIAJ, 0 , 200 pF) 250V -0.3V to +6V Input Voltage (RIN+, RIN-) -0.3V to (VCC + 0.3V) Output Voltage (ROUT) -0.3V to (VCC + 0.3V) Recommended Operating Conditions Maximum Package Power Dissipation @ +25C M Package Min Typ Max Supply Voltage (VCC) +4.5 +5.0 +5.5 V Receiver Input Voltage GND 2.4 V +85 C 1025 mW Derate M Package 8.2 mW/C above +25C Storage Temperature Range Operating Free Air -65C to +150C Temperature (TA) Lead Temperature Range Soldering (4 sec.) Units -40 +25 +260C Electrical Characteristics Over Supply Voltage and Operating Temperature ranges, unless otherwise specified. (Note 2) Symbol Parameter Conditions VTH Differential Input High Threshold VTL Differential Input Low Threshold IIN Input Current VCM = + 1.2V VIN = +2.4V Pin Min RIN+, RIN- -100 VCC = 5.5V VOH Output High Voltage -10 IOH = -0.4 mA, VID = +200 mV ROUT Max +100 -10 VIN = 0V Typ Units mV mV 1 1 +10 A +10 A 3.8 4.9 V IOH = -0.4mA, Inputs terminated 3.8 4.9 V IOH = -0.4mA, Inputs Open 3.8 4.9 V IOH = -0.4mA, Inputs Shorted 4.9 VOL Output Low Voltage IOL = 2 mA, VID = -200 mV 0.07 0.3 V IOS Output Short Circuit Current VOUT = 0V (Note 8) -60 -100 mA ICC No Load Supply Current Inputs Open 3.5 10 mA Typ Max Units -15 VCC V Switching Characteristics VCC = +5.0V 10%, TA = -40C to +85C (Notes 3, 4, 5, 6, 9) Symbol Parameter tPHLD Differential Propagation Delay High to Low tPLHD Differential Propagation Delay Low to High tSKD Differential Skew |tPHLD - tPLHD| tSK1 Channel-to-Channel Skew (Note 5) tSK2 Chip to Chip Skew (Note 6) tTLH Rise Time tTHL Fall Time www.national.com Conditions CL = 5 pF, VID = 200 mV (Figure 1 and Figure 2) 2 Min 1.0 3.40 6.0 ns 1.0 3.48 6.0 ns 0 0.08 1.2 ns 0 0.6 1.5 ns 5.0 ns 0.5 2.5 ns 0.5 2.5 ns DS90C402 Parameter Measurement Information 10000604 FIGURE 1. Receiver Propagation Delay and Transition Time Test Circuit 10000605 FIGURE 2. Receiver Propagation Delay and Transition Time Waveforms Typical Application 10000608 FIGURE 3. Point-to-Point Application offset voltage which is typically +1.2V. The driven signal is centered around this voltage and may shift 1V around this center point. The 1V shifting may be the result of a ground potential difference between the driver's ground reference and the receiver's ground reference, the common-mode effects of coupled noise, or a combination of the two. Both receiver input pins should honor their specified operating input voltage range of 0V to +2.4V (measured from each pin to ground), exceeding these limits may turn on the ESD protection circuitry which will clamp the bus voltages. Fail-Safe Feature: The LVDS receiver is a high gain, high speed device that amplifies a small differential signal (20mV) to CMOS logic levels. Due to the high gain and tight threshold of the receiver, care should be taken to prevent noise from appearing as a valid signal. The receiver's internal fail-safe circuitry is designed to source/sink a small amount of current, providing fail-safe protection (a stable known state HIGH output voltage) for floating, terminated or shorted receiver inputs. Applications Information LVDS drivers and receivers are intended to be primarily used in an uncomplicated point-to-point configuration as is shown in Figure 3. This configuration provides a clean signaling environment for the quick edge rates of the drivers. The receiver is connected to the driver through a balanced media which may be a standard twisted pair cable, a parallel pair cable, or simply PCB traces. Typically the characteristic impedance of the media is in the range of 100. A termination resistor of 100 should be selected to match the media, and is located as close to the receiver input pins as possible. The termination resistor converts the current sourced by the driver into a voltage that is detected by the receiver. Other configurations are possible such as a multi-receiver configuration, but the effects of a mid-stream connector(s), cable stub(s), and other impedance discontinuities as well as ground shifting, noise margin limits, and total termination loading must be taken into account. The DS90C402 differential line receiver is capable of detecting signals as low as 100 mV, over a 1V common-mode range centered around +1.2V. This is related to the driver 3 www.national.com DS90C402 Applications Information ential input voltage, the receiver output will remain in a HIGH state. Shorted input fail-safe is not supported across the common-mode range of the device (GND to 2.4V). It is only supported with inputs shorted and no external common-mode voltage applied. (Continued) 1. Open Input Pins. The DS90C402 is a dual receiver device, and if an application requires only one receiver, the unused channel(s) inputs should be left OPEN. Do not tie unused receiver inputs to ground or any other voltages. The input is biased by internal high value pull up and pull down resistors to set the output to a HIGH state. This internal circuitry will guarantee a HIGH, stable output state for open inputs. 2. Terminated Input. If the driver is disconnected (cable unplugged), or if the driver is in a power-off condition, the receiver output will again be in a HIGH state, even with the end of cable 100 termination resistor across the input pins. The unplugged cable can become a floating antenna which can pick up noise. If the cable picks up more than 10mV of differential noise, the receiver may see the noise as a valid signal and switch. To insure that any noise is seen as common-mode and not differential, a balanced interconnect should be used. Twisted pair cable will offer better balance than flat ribbon cable Pin Descriptions Pin No. Name 2, 6 ROUT Receiver output pin Description 3, 7 RIN+ Positive receiver input pin 4, 8 RIN- Negative receiver input pin 5 GND Ground pin 1 VCC Positive power supply pin, +5V 10% Ordering Information 3. Shorted Inputs. If a fault condition occurs that shorts the receiver inputs together, thus resulting in a 0V differ- Operating Temperature Package Type/ Number Order Number -40C to +85C SOP/M08A DS90C402M RECEIVE MODE RIN+ - RIN- ROUT > +100 mV < -100 mV 100 mV > & > -100 mV H L X H = Logic High Level L = Logic Low level X = Indeterminant State Note 1: "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices should be operated at these limits. The table of "Electrical Characteristics" specifies conditions of device operation. Note 2: Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground unless otherwise specified. Note 3: All typicals are given for: VCC = +5.0V, TA = +25C. Note 4: Generator waveform for all tests unless otherwise specified: f = 1 MHz, ZO = 50, tr and tf (0%-100%) 1 ns for RIN. Note 5: Channel-to-Channel Skew is defined as the difference between the propagation delay of one channel and that of the others on the same chip with an event on the inputs. Note 6: Chip to Chip Skew is defined as the difference between the minimum and maximum specified differential propagation delays. Note 7: ESD Rating: HBM (1.5 k, 100 pF) 3,500V EIAJ (0, 200 pF) 250V Note 8: Output short circuit current (IOS) is specified as magnitude only, minus sign indicates direction only. Only one output should be shorted at a time, do not exceed maximum junction temperature specification. Note 9: CL includes probe and jig capacitance. www.national.com 4 DS90C402 Typical Performance Characteristics Output High Voltage vs Power Supply Voltage Output High Voltage vs Ambient Temperature 10000609 10000610 Output Low Voltage vs Power Supply Voltage Output Low Voltage vs Ambient Temperature 10000611 10000612 5 www.national.com DS90C402 Typical Performance Characteristics (Continued) Output Short Circuit Current vs Power Supply Voltage Output Short Circuit Current vs Ambient Temperature 10000613 10000614 Differential Propagation Delay vs Power Supply Voltage Differential Propagation Delay vs Ambient Temperature 10000615 www.national.com 10000616 6 DS90C402 Typical Performance Characteristics (Continued) Differential Skew vs Power Supply Voltage Differential Skew vs Ambient Temperature 10000618 10000617 Transition Time vs Power Supply Voltage Transition Time vs Ambient Temperature 10000619 10000620 7 www.national.com DS90C402 Dual Low Voltage Differential Signaling (LVDS) Receiver Physical Dimensions inches (millimeters) unless otherwise noted 8-Lead (0.150" Wide) Molded Small Outline Package, JEDEC Order Number DS90C402M NS Package Number M08A National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. Leadfree products are RoHS compliant. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated