MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS For photo flash @RoHS Compliant ?SPECIFICATIONS Items Characteristics Category Temperature Range Rated Voltage Range Capacitance Tolerance Leakage Current Dissipation Factor (tane) -20 to +55C 300, 315, 330Vdc -10 to +20% (V) I=1BC Where, I : Max. leakage current (MA), C : Nominal capacitance (MF) (at 20C, 120Hz) (at 20C after 5 minutes) 0.06max. Charge and Discharge Characteristics Shelf Life (at 20C, 120Hz) The following specifications shall be satisfied when the capacitors are restored to 20C after charge and discharge are repeated 5,000 times at room temperature (5 to 35C). Discharge resistance or Xenon tube : 0.7 to 1.0O. Capacitance change [P10% of the initial value D.F. (tanE) [150% of the initial specified value Leakage current [150% of the initial specified value The following specifications shall be satisfied when the capacitors are restored to 20C after exposing them for 1,000 hours at 55C without voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4. Capacitance change [P10% of the initial value D.F. (tanE) [150% of the initial specified value Leakage current [150% of the initial specified value ?DIMENSIONS [mm] fD 6.0 to 7.5 8.0 to 8.5 9.0 to 9.5 10.0 to 14.0 14.5 to 18.0 0.6 0.6 fd 0.5 0.6 0.8 5 4 F 2.5 3.5 7.5 fD' FD+0.5max. L' L+1.0max. FD' Fd Sleeve (PET : Black) FP0.5 @Terminal Code : E L' Vent 15min. 4min. ?PART NUMBERING SYSTEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 E P H - A A A E A A A A A MA A A S Supplement code Size code (L code) Size code (FD code) Nominal capacitance code (ex. 50MF:500,100MF:101) Lead forming*taping code Terminal code Rated voltage code (ex. 315V:3B1,330V:331) Series code Category @Size Code FD code (14th, 15th) Please refer to "Product code guide (radial lead type)" (1/2) FD(mm) 6.0 6.5 7.0 7.5 8.0 8.5 9.0 9.5 10.0 10.5 11.0 11.5 12.0 12.5 13.0 13.5 14.0 14.5 15.0 15.5 16.0 16.5 17.0 17.5 18.0 FD code 14th 15th 0 6 5 6 0 7 5 7 0 8 5 8 0 9 5 9 0 A 5 A 0 B 5 B 0 C 5 C 0 D 5 D 0 E 5 E 0 F 5 F 0 G 5 G 0 H 5 H 0 J L code (16th, 17th) L(mm) 15.0 16.0 17.0 18.0 19.0 20.0 21.0 22.0 23.0 24.0 25.0 26.0 27.0 28.0 29.0 30.0 31.0 32.0 33.0 34.0 35.0 36.0 37.0 38.0 39.0 40.0 41.0 42.0 43.0 44.0 45.0 L code 16th 17th 5 1 6 1 7 1 8 1 9 1 0 2 1 2 2 2 3 2 4 2 5 2 6 2 7 2 8 2 9 2 0 3 1 3 2 3 3 3 4 3 5 3 6 3 7 3 8 3 9 3 0 4 1 4 2 4 3 4 4 4 5 4 CAT. No. E1001K MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS For photo flash ?RATINGS (REFERENCE) WV (Vdc) 315 330 Cap (mF) Case size fDbL(mm) tane 86 122 144 209 80 114 137 194 10B30 10B40 12.5B30 12.5B40 10B30 10B40 12.5B30 12.5B40 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 Part No. EPH-3B1ESS860A030S EPH-3B1ESS121A040S EPH-3B1ESS1E1C530S EPH-3B1ESS211C540S EPH-331ESS800A030S EPH-331ESS1B1A040S EPH-331ESS1D1C530S EPH-331ESS1K1C540S SS : Enter the appropriate lead forming or taping code. @Products of vents on the sealing rubber DIMENSIONS[mm] <In the case of diameter 10mm> Lead Wire Vent f V F FD 10 V (4.6) f (1.8) F 5P0.5 Products of vent on rubber type, please make clearance about 1mm minimum between rubber and board. If it is difficult to make clearance 1mm minimum between rubber and board, please arrange gas escaping hole on the board (same position and 40% minimum diameter from the vent). The products of dual vents on rubber, requires placement one or two gas escaping hole on the board. @Products of a vent on the case Please make the following open space over the vent so that the vent can operate correctly. Case diameter F6 to 16mm F16.5mm and up Clearance 2mm minimum 3mm minimum Above part numbers are only reference. Please consult with us about detail specifications (rated voltage, capacitance, case size, type of rubber, etc...). (2/2) CAT. No. E1001K