1
FEATURES
1
2
3
4
8
7
6
5
1OUT
1IN–
1IN+
GND
VCC
2OUT
2IN–
2IN+
LM293...DPACKAGE
(TOP VIEW)
DESCRIPTION/ORDERING INFORMATION
LM293-EPDUAL DIFFERENTIAL COMPARATOR
SLCS155 – OCTOBER 2007www.ti.com
•Controlled Baseline •Low Supply-Current Drain Independent ofSupply Voltage . . . 0.4 mA Typical Per– One Assembly
Comparator– Test Site
•Low Input Bias Current . . . 25 nA Typical– One Fabrication Site
•Low Input Offset Voltage . . . 2 mV Typical•Extended Temperature Performance of
•Common-Mode Input Voltage Range Includes– 55 °C to 125 °C
Ground•Enhanced Diminishing Manufacturing Sources
•Differential Input Voltage Range Equal to(DMS) Support
Maximum-Rated Supply Voltage . . . ± 36 V•Enhanced Product Change Notification
•Low Output Saturation Voltage•Qualification Pedigree
(1)
•Output Compatible With TTL, MOS, and CMOS•Single Supply or Dual Supplies•Wide Range of Supply Voltage– Max Rating . . . 2 V to 36 V– Tested to 30 V(1) Component qualification in accordance with JEDEC andindustry standards to ensure reliable operation over anextended temperature range. This includes, but is not limitedto, Highly Accelerated Stress Test (HAST) or biased 85/85,temperature cycle, autoclave or unbiased HAST,electromigration, bond intermetallic life, and mold-compoundlife. Such qualification testing should not be viewed asjustifying use of this component beyond specifiedperformance and environmental limits.
This device consist of two independent voltage comparators that are designed to operate from a single powersupply over a wide range of voltages. Operation from dual supplies also is possible as long as the differencebetween the two supplies is 2 V to 36 V, and V
CC
is at least 1.5 V more positive than the input common-modevoltage. Current drain is independent of the supply voltage. The outputs can be connected to otheropen-collector outputs to achieve wired-AND relationships.
The LM293-EP is characterized for operation from – 55 °C to 125 °C.
ORDERING INFORMATION
(1)
V
IOmaxT
A
MAX V
CC
PACKAGE
(2)
ORDERABLE PART NUMBER TOPSIDE MARKINGAT 25 °C
– 55 °C to 125 °C 5 mV 30 V SOIC – D Reel of 2500 LM293MDREP LM293E
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TIwebsite at www.ti.com .(2) Package drawings, thermal data, and symbolization are available at www.ti.com/packaging .
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications ofTexas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Copyright © 2007, Texas Instruments IncorporatedProducts conform to specifications per the terms of the TexasInstruments standard warranty. Production processing does notnecessarily include testing of all parameters.
www.ti.com
Symbol (Each Comparator)
IN+
IN–
OUT
Schematic (Each Comparator)
80 mA
CurrentRegulator
80 mA
60 m
A
10 mA
VCC
10 mA
OUT
GND
IN+
IN-
Epi-FET
Diodes
Resistors
Transistors
Currentvaluesshownarenominal.
COMPONENTCOUNT
1
2
2
30
Absolute Maximum Ratings
(1)
LM293-EP
DUAL DIFFERENTIAL COMPARATOR
SLCS155 – OCTOBER 2007
over operating free-air temperature range (unless otherwise noted)
MIN MAX UNIT
V
CC
Supply voltage
(2)
36 VV
ID
Differential input voltage
(3)
± 36 VV
I
Input voltage range (either input) – 0.3 36 VV
O
Output voltage 36 VI
O
Output current 20 mADuration of output short-circuit to ground
(4)
Unlimited
θ
JA
Package thermal impedance
(5) (6)
D package 97 °C/WT
J
Operating virtual junction temperature 150 °CT
stg
Storage temperature range – 65 150 °C
(1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratingsonly, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operatingconditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.(2) All voltage values, except differential voltages, are with respect to GND.(3) Differential voltages are at IN+, with respect to IN – .(4) Short circuits from outputs to V
CC
can cause excessive heating and eventual destruction.(5) Maximum power dissipation is a function of T
J
(max), θ
JA
, and T
A
. The maximum allowable power dissipation at any allowable ambienttemperature is P
D
= (T
J
(max) – T
A
)/ θ
JA
. Operating at the absolute maximum T
J
of 150 °C can affect reliability.(6) The package thermal impedance is calculated in accordance with JESD 51-7.
2Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): LM293-EP
www.ti.com
Electrical Characteristics
Switching Characteristics
LM293-EPDUAL DIFFERENTIAL COMPARATOR
SLCS155 – OCTOBER 2007
at specified free-air temperature, V
CC
= 5 V (unless otherwise noted)
LM293PARAMETER TEST CONDITIONS T
A
(1)
UNITMIN TYP MAX
V
CC
= 5 V to 30 V, 25 °C 2 5V
IO
Input offset voltage V
O
= 1.4 V, mVFull range 9V
IC
= V
IC(min)
25 °C 5 50I
IO
Input offset current V
O
= 1.4 V nAFull range 25025 °C – 25 – 250I
IB
Input bias current V
O
= 1.4 V nAFull range – 40025 °C 0 toVCC – 1.5Common-mode inputV
ICR
Vvoltage range
(2)
Full range 0 toVCC – 2Large-signal V
CC
= 15 V,A
VD
differential-voltage V
O
= 1.4 V to 11.4 V, 25 °C 50 200 V/mVamplification R
L
≥15 k Ωto V
CC
V
OH
= 5 V, V
ID
= 1 V 25 °C 0.1 50 nAI
OH
High-level output current
V
OH
= 30 V, V
ID
= 1 V Full range 1 μA25 °C 150 400V
OL
Low-level output voltage I
OL
= 4 mA, V
ID
= – 1 V mVFull range 700I
OL
Low-level output current V
OL
= 1.5 V, V
ID
= – 1 V 25 °C 6 mAV
CC
= 5 V 25 °C 0.8 1I
CC
Supply current R
L
=∞mAV
CC
= 30 V Full range 2.5
(1) Full range (MIN or MAX) for LM293 is – 55 °C to 125 °C. All characteristics are measured with zero common-mode input voltage, unlessotherwise specified.(2) The voltage at either input or common-mode should not be allowed to go negative by more than 0.3 V. The upper end of thecommon-mode voltage range is V
CC+
– 1.5 V for the inverting input ( – ), and the non-inverting input (+) can exceed the V
CC
level; thecomparator provides a proper output state. Either or both inputs can go to 30 V without damage.
V
CC
= 5 V, T
A
= 25 °C
LM293PARAMETER TEST CONDITIONS UNITTYP
100 mV input step with 5 mV overdrive 1.3R
L
connected to 5 V through 5.2 k Ω,Response time μsC
L
= 15 pF
(1)
, See
(2)
TTL-level input step 0.3
(1) C
L
includes probe and jig capacitance.(2) The response time specified is the interval between the input step function and the instant when the output crosses 1.4 V.
Copyright © 2007, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Link(s): LM293-EP
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0 (mm) B0 (mm) K0 (mm) P1
(mm) W
(mm) Pin1
Quadrant
LM293MDREP SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 19-Mar-2008
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM293MDREP SOIC D 8 2500 340.5 338.1 20.6
PACKAGE MATERIALS INFORMATION
www.ti.com 19-Mar-2008
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated