CMX867E2 - CML Microcircuits - Datasheet.Directory

CML Microcircuits

COMMUNICATION SEMICONDUCTORS

CMX867

Low Power

V.22 Modem

 2004 Consumer Microcircuits Limited

D/867/5 March 2004 Provisional Issue

Features Applications

•• V.22, Bell 212A 1200/1200 or 600/600 bps DPSK •• Telephone Telemetry Systems

•• V.23 1200/75, 1200/1200, 75, 1200 bps FSK •• Remote Utility Meter Reading

•• Bell 202 1200/150, 1200/1200, 150, 1200 bps FSK •• Security Systems

•• V.21 or Bell 103 300/300 bps FSK •• Industrial Control Systems

•• DTMF/Tones Transmit and Receive •• Electronic Cash Terminals

•• ‘Powersave’ Standby Mode •• Pay-Phones

•• Software and Hardware Compatible with CMX868 •• Cable TV Set-Top Boxes

1.1 Brief Description

The CMX867 is a multi-standard modem for use in telephone based information and telemetry systems.

Control of the device is via a simple high speed serial bus, compatible with most types of µC serial

interface. The data transmitted and received by the modem is also transferred over the same serial bus.

On-chip programmable Tx and Rx USARTs meeting the requirements of V.14 are provided for use with

asynchronous data and allow unformatted synchronous data to be received or transmitted as 8-bit words.

It can transmit and detect standard DTMF and modem calling and answer signals or user-specific

programmed single or dual tone signals. A general purpose Call Progress signal detector is also included.

Flexible line driver and receive hybrid circuits are integrated on chip, requiring only passive external

components to build a 2 or 4-wire line interface.

The device also features a Hook Switch Relay Drive output and a Ring Detector circuit which continues

to function when the device is in the Powersave mode, providing an interrupt which can be used to wake

up the host µController when line voltage reversal or ringing is detected.

The CMX867 operates from a single 2.7 to 5.5V supply over a temperature range of -40°C to +85°C and

is available in 24-pin TSSOP, SOIC and DIP packages.

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 2 D/867/5

CONTENTS

Section Page

1.1 Brief Description..................................................................................1

1.2 Block Diagram .....................................................................................3

1.3 Signal List............................................................................................4

1.4 External Components..........................................................................5

1.4.1 Ring Detector Interface...........................................................6

1.4.2 Line Interface...........................................................................7

1.5 General Description...........................................................................10

1.5.1 Tx USART..............................................................................11

1.5.2 FSK and DPSK Modulators ..................................................12

1.5.3 Tx Filter and Equaliser..........................................................13

1.5.4 DTMF/Tone Generator..........................................................13

1.5.5 Tx Level Control and Output Buffer.....................................13

1.5.6 Rx DTMF/Tones Detectors....................................................14

1.5.7 Rx Modem Filterering and Demodulation............................15

1.5.8 Rx Modem Pattern Detectors and Descrambler ..................16

1.5.9 Rx Data Register and USART ...............................................16

1.5.10 C-BUS Interface.....................................................................18

1.5.10.1 General Reset Command..............................18

1.5.10.2 General Control Register..............................20

1.5.10.3 Transmit Mode Register ...............................22

1.5.10.4 Receive Mode Register.................................26

1.5.10.5 Tx Data Register............................................28

1.5.10.6 Rx Data Register ...........................................28

1.5.10.7 Status Register..............................................29

1.5.10.8 Programming Register..................................32

1.6 Application Notes..............................................................................36

1.6.1 V.22 Calling Modem Application..........................................36

1.6.2 V.22 Answering Modem Application....................................37

1.6.3 Reference Diagrams..............................................................37

1.7 Performance Specification................................................................38

1.7.1 Electrical Performance..........................................................38

1.7.1.1 Absolute Maximum Ratings.....................................38

1.7.1.2 Operating Limits.......................................................38

1.7.1.3 Operating Characteristics........................................39

1.7.2 Packaging..............................................................................46

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 3 D/867/5

1.2 Block Diagram

Figure 1 Block Diagram

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 4 D/867/5

1.3 Signal List

CMX867

D2/E2/P4 Signal Description

Pin No. Name Type

1 XTALN O/P The output of the on-chip Xtal oscillator inverter.

2 XTAL/CLOCK I/P The input to the oscillator inverter from the Xtal

circuit or external clock source.

3 RDRVN O/P Relay drive output, low resistance pull down to

VSS when active and medium resistance pull up

to VDD when inactive.

4, 8, 12, 17, 21 VSS Power The negative supply rail (ground).

5 RD I/P Schmitt trigger input to the Ring signal detector.

Connect to VSS if Ring Detector not used.

6 RT BI Open drain output and Schmitt trigger input

forming part of the Ring signal detector.

Connect to VDD if Ring Detector not used.

7, 16, 24 VDD Power The positive supply rail. Levels and thresholds

within the device are proportional to this

voltage.

9 RXAFB O/P The output of the Rx Input Amplifier.

10 RXAN I/P The inverting input to the Rx Input Amplifier

11 RXA I/P The non-inverting input to the Rx Input Amplifier

13 VBIAS O/P Internally generated bias voltage of

approximately VDD /2, except when the device

is in ‘Powersave’ mode when VBIAS will

discharge to VSS. Should be decoupled to VSS

by a capacitor mounted close to the device pins.

14 TXAN O/P The inverted output of the Tx Output Buffer.

15 TXA O/P The non-inverted output of the Tx Output Buffer.

18 CSN I/P The C-BUS chip select input from the µC.

19 COMMAND

DATA I/P The C-BUS serial data input from the µC.

20 SERIAL

CLOCK I/P The C-BUS serial clock input from the µC.

22 REPLY DATA T/S A 3-state C-BUS serial data output to the µC.

This output is high impedance when not sending

data to the µC.

23 IRQN O/P A ‘wire-ORable’ output for connection to a µC

Interrupt Request input. This output is pulled

down to VSS when active and is high impedance

when inactive. An external pullup resistor is

required ie R1 of Figure 2.

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 5 D/867/5

Notes:

I/P = Input

O/P = Output

BI = Bidirectional

T/S = 3-state Output

NC = No Connection

1.4 External Components

R1 100kΩ C1, C2 22pF

X1 11.0592MHz C3, C4 100nF

or 12.288MHz C5 10uF

Resistors ±5%, capacitors ±20% unless otherwise stated.

Figure 2 Recommended External Components for Typical Application

This device is capable of detecting and decoding small amplitude signals. To achieve this VDD and

VBIAS should be decoupled and the receive path protected from extraneous in-band signals. It is

recommended that the printed circuit board is laid out with a VSS ground plane in the CMX867 area to

provide a low impedance connection between the VSS pins and the VDD and VBIAS decoupling capacitors.

The V

SS connections to the Xtal oscillator capacitors C1 and C2 should also be low impedance and

preferably be part of the VSS ground plane to ensure reliable start up of the oscillator.

For best results, an Xtal oscillator design should drive the clock inverter input with signal levels of at least

40% of VDD peak-to-peak. Tuning-fork Xtals generally cannot meet this requirement. To obtain Xtal

oscillator design assistance, please consult your Xtal manufacturer.

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 6 D/867/5

1.4.1 Ring Detector Interface

Figure 3 shows how the CMX867 may be used to detect the large amplitude Ringing signal voltage

present on the 2-wire line at the start of an incoming telephone call.

The ring signal is usually applied at the subscriber's exchange as an ac voltage inserted in series with

one of the telephone wires and will pass through either C20 and R20 or C21 and R21 to appear at the top

end of R22 (point X in Figure 3) in a rectified and attenuated form.

The signal at point X is further attenuated by the potential divider formed by R22 and R23 before being

applied to the CMX867 RD input. If the amplitude of the signal appearing at RD is greater than the input

threshold (Vthi) of Schmitt trigger 'A' then the N transistor connected to RT will be turned on, pulling the

voltage at RT to VSS by discharging the external capacitor C22. The output of the Schmitt trigger 'B' will

then go high, setting bit 14 (Ring Detect) of the Status Register.

The minimum amplitude ringing signal that is certain to be detected is:

( 0.7 + Vthi x [R20 + R22 + R23] / R23 ) x 0.707 Vrms

where Vthi is the high-going threshold voltage of the Schmitt trigger A (see section 1.7.1).

With R20-22 all 470kΩ as Figure 3, then setting R23 to 68kΩ will guarantee detection of ringing signals

of 40Vrms and above for VDD over the range 3 to 5V.

R20, 21, 22 470kΩ C20, 21 0.1µF

R23 See text C22 0.33µF

R24 470kΩ D1-4 1N4004

Resistors ±5%, capacitors ±20%

Figure 3 Ring Signal Detector Interface Circuit

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 7 D/867/5

If the time constant of R24 and C22 is large enough then the voltage on RT will remain below the

threshold of the 'B' Schmitt trigger for the duration of a ring cycle.

The time for the voltage on RT to charge from VSS towards VDD can be derived from the formula

VRT = VDD x [1 - exp(-t/(R24 x C22)) ]

As the Schmitt trigger high-going input threshold voltage (Vthi) has a minimum value of 0.56 x VDD, then

the Schmitt trigger B output will remain high for a time of at least 0.821 x R24 x C22 following a pulse at

RD.

The values of R24 and C22 given in Figure 3 (470kΩ and 0.33µF) give a minimum RT charge time of

100 msec, which is adequate for ring frequencies of 10Hz or above.

Note that the circuit will also respond to a telephone line voltage reversal. If necessary the µC can

distinguish between a Ring signal and a line voltage reversal by measuring the time that bit 14 of the

Status Register (Ring Detect) is high.

If the Ring detect function is not used then pin RD should be connected to VSS and RT to VDD.

1.4.2 Line Interface

A line interface circuit is needed to provide dc isolation and to terminate the line. Typical interface circuits

are described below.

2-Wire Line Interface

Figure 4a shows a simplified interface for use with a 600Ω 2-wire line. The complex line termination is

provided by R13 and C10, high frequency noise is attenuated by C10 and C11, while R11 and R12 set

the receive signal level into the modem. For clarity the 2-wire line protection circuits have not been

shown.

R11 See text C3 See Figure 2

R12 100kΩ C10 33nF

R13 600Ω C11 100pF

Resistors ±5%, capacitors ±20%

Figure 4a 2-Wire Line Interface Circuit

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 8 D/867/5

Resistor R13 is used to match the AC impedance of the interface to the line. With an ideal transformer

this resistor would be equal to the desired impedance (e.g. 600Ω); however in practice with a real

transformer, R13 should be set such that the interface as a whole presents the desired impedance. Line

transformer manufacturers normally provide guidance in this regard.

The transmit line signal level is determined by the voltage swing between the TXA and TXAN pins, less

6dB due to the line termination, and less the loss in the line coupling transformer.

Allowing for 1dB loss in the transformer, then with the Tx Mode Register set for a Tx Level Control gain

of 0dB the nominal transmit line levels will be:

VDD = 3.0V VDD = 5.0V

QAM, DPSK and FSK Tx modes (no guard tone) -10dBm -5.5dBm

Single tone transmit mode -10dBm -5.5dBm

DTMF transmit mode -6 and -8 dBm -1.5 and -3.5 dBm

For a line impedance of 600Ω, 0dBm = 775mVrms. See also section 1.7.1.3

In the receive direction, the signal detection thresholds within the CMX868 are proportional to VDD and

are affected by the Rx Gain Control gain setting in the Rx Mode Register. The signal level into the

CMX868 is affected by the line coupling transformer loss and the values of R11 and R12 of Figure 4a.

Assuming 1dB transformer loss, the Rx Gain Control programmed to 0dB and R12 = 100kΩ, then for

correct operation (see section 1.7.1.3) the value of R11 should be equal to 500 / VDD kΩ i.e. 160kΩ at

3.0V, falling to 100kΩ at 5.0V.

For best Rx performance it is recommended that the transformer coupling arrangement should provide at

least 7dB trans-hybrid loss. This is achieved by minimising the amount of the transmitted signal

presented to the receiver at RXAFB. A mis-match between the transformer impedance and R13 will

result in a proportion of the transmitted signal being fed to the receiver op-amp circuit via R11. The effect

of this can be significantly nulled by careful selection of the potential divider components R14 and R15 to

provide a cancellation signal at RXA. (Note: with an ideal transformer, R13 would be set equal to the line

impedance, and R14 would be set equal to R15.

Further details of line interfacing can be found in the EV8680 and DE8681 User Manuals, available from

the CML website.

As an example, the following component values are appropriate for use with the MIDCOM 82111 line

transformer:

R11 See text C10 33nF

R12 100kΩ C11 100pF

R13 392Ω C12 0.1µF

R14 120k C13 47pF

R15 180k

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 9 D/867/5

4-Wire Line Interface

Figure 4b shows a simplified interface for use with a 600Ω 4-wire line. The line terminations are provided

by R10 and R13, the values of which are dependent on the choice of transformer: see notes above. High

frequency noise is attenuated by C11 while R11 and R12 set the receive signal level into the modem.

Transmit and receive line level settings and the value of R11 are as for the 2-wire circuit.

R10, 13 See text C3 See Figure 2

R11 See text C11 100pF

R12 100kΩ C12 33nF

Resistors ±5%, capacitors ±20%

Figure 4b 4-Wire Line Interface Circuit

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 10 D/867/5

1.5 General Description

The CMX867 transmit and receive operating modes are independently programmable.

The transmit mode can be set to any one of the following:

V.22 and Bell 212A modem. 1200 or 600 bps DPSK (Differential Phase Shift Keying).

V.21 modem. 300bps FSK (Frequency Shift Keying).

Bell 103 modem. 300bps FSK.

V.23 modem. 1200 or 75 bps FSK.

Bell 202 modem. 1200 or 150 bps FSK.

DTMF transmit.

Single tone transmit (from a range of modem calling, answer and other tone frequencies)

User programmed tone or tone pair transmit (programmable frequencies and levels)

Disabled.

The receive mode can be set to any one of the following:

V.22 and Bell 212A modem. 1200 or 600 bps DPSK.

V.21 modem. 300bps FSK.

Bell 103 modem. 300 bps FSK.

V.23 modem. 1200 or 75 bps FSK.

Bell 202 modem. 1200 or 150 bps FSK.

DTMF detect.

2100Hz and 2225Hz answer tone detect.

Call progress signal detect.

User programmed tone or tone pair detect.

Disabled.

The CMX867 may also be set into a Powersave mode which disables all circuitry except for the C-BUS

interface and the Ring Detector.

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 11 D/867/5

1.5.1 Tx USART

A flexible Tx USART is provided for all modem modes, meeting the requirements of V.14 for DPSK

modems.

It can be programmed to transmit continuous patterns, Start-Stop characters or Synchronous Data.

In both Synchronous Data and Start-Stop modes the data to be transmitted is written by the µC into the

8-bit C-BUS Tx Data Register from which it is transferred to the Tx Data Buffer.

If Synchronous Data mode has been selected the 8 data bits in the Tx Data Buffer are transmitted

serially, b0 being sent first.

In Start-Stop mode a single Start bit is transmitted, followed by 5, 6, 7 or 8 data bits from the Tx Data

Buffer - b0 first - followed by an optional Parity bit then - normally - one or two Stop bits. The Start, Parity

and Stop bits are generated by the USART as determined by the Tx Mode Register settings and are not

taken from the Tx Data Register.

Figure 5a Tx USART

Every time the contents of the C-BUS Tx Data Register are transferred to the Tx Data Buffer the Tx Data

Ready flag bit of the Status Register is set to 1 to indicate that a new value should be loaded into the C-

BUS Tx Data Register. This flag bit is cleared to 0 when a new value is loaded into the Tx Data Register.

Figure 5b Tx USART Function (Start-Stop mode, 8 Data Bits + Parity)

If a new value is not loaded into the Tx Data Register in time for the next Tx Data Register to Tx Data

Buffer transfer then the Status Register Tx Data Underflow bit will be set to 1. In this event the contents

of the Tx Data Buffer will be re-transmitted if Synchronous Data mode has been selected, or if the Tx

modem is in Start-Stop mode then a continuous Stop signal (1) will be transmitted until a new value is

loaded into the Tx Data Register.

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 12 D/867/5

In all modes the transmitted bit and baud rates are the nominal rates for the selected modem type, with

an accuracy determined by the XTAL frequency accuracy, however for DPSK modes V.14 requires that

Start-Stop characters can be transmitted at up to 1% overspeed (basic signalling rate range) or 2.3%

overspeed (extended signalling rate range) by deleting a Stop bit from no more than one out of every 8

(basic range) or 4 (extended range) consecutive transmitted characters.

To accommodate the V.14 requirement the Tx Data Register has been given two C-BUS addresses, $E3

and $E4. Data should normally be written to $E3.

In DPSK Start-Stop modes if data is written to $E4 then the programmed number of Stop bits will be

reduced by one for that character. In this way the µC can delete transmitted Stop bits as needed.

In FSK Start-Stop modes, data written to $E4 will be transmitted with a 12.5% reduction in the length of

the Stop bit at the end of that character.

In all Synchronous Data modes data written to $E4 will be treated as though it had been written to $E3.

The underspeed transmission requirement of V.14 is automatically met by the CMX867 as in Start-Stop

mode it automatically inserts extra Stop bit(s) if it has to wait for new data to be loaded into the C-BUS

Tx Data Register.

The optional V.22 compatible data scrambler can be programmed to invert the next input bit in the event

of 64 consecutive ones appearing at its input. It uses the generating polynomial:

1 + x-14 + x-17

1.5.2 FSK and DPSK Modulators

Serial data from the USART is fed via the optional scrambler to the FSK modulator if V.21, V.23, Bell

103 or Bell 202 mode has been selected or to the DPSK modulator for V.22 and Bell 212A modes.

The FSK modulator generates one of two frequencies according to the transmit mode and the value of

current transmit data bit.

The DPSK modulator generates a carrier of 1200Hz (Low Band, Calling modem) or 2400Hz (High Band,

Answering modem) which is modulated at 600 symbols/sec as described below:

600bps V.22 signals are transmitted as a +90° carrier phase change for a ‘0’ bit, +270° for ‘1’.

For V.22 and Bell 212A 1200bps DPSK the transmit data stream is divided into groups of two

consecutive bits (dibits) which are encoded as a carrier phase change:

Dibit

(left-hand bit is the

first of the pair)

Phase change

00 +90°

01 0°

11 +270°

10 +180°

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 13 D/867/5

1.5.3 Tx Filter and Equaliser

The FSK or DPSK modulator output signal is fed through the Transmit Filter and Equaliser block which

limits the out-of-band signal energy to acceptable limits. In 600 and 1200 bps FSK and DPSK modes this

block includes a fixed compromise line equaliser which is automatically set for the particular modulation

type and frequency band being employed. This fixed compromise line equaliser may be enabled or

disabled by bit 10 of the General Control Register. The amount of Tx equalisation provided compensates

for one quarter of the relative amplitude and delay distortion of ETS Test Line 1 over the frequency band

used.

1.5.4 DTMF/Tone Generator

In DTMF/Tones mode this block generates DTMF signals or single or dual frequency tones. In DPSK

modem modes it is used to generate the optional 550 or 1800Hz guard tone.

1.5.5 Tx Level Control and Output Buffer

The outputs (if present) of the Transmit Filter and DTMF/Tone Generator are summed then passed

through the programmable Tx Level Control and Tx Output Buffer to the pins TXA and TXAN. The Tx

Output Buffer has symmetrical outputs to provide sufficient line voltage swing at low values of VDD and

to reduce harmonic distortion of the signal.

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 14 D/867/5

1.5.6 Rx DTMF/Tones Detectors

In Rx Tones Detect mode the received signal, after passing through the Rx Gain Control block, is fed to

the DTMF / Tones / Call Progress / Answer Tone detector. The user may select any of four separate

detectors:

The DTMF detector detects standard DTMF signals. A valid DTMF signal will set bit 5 of the Status

The programmable tone pair detector includes two separate tone detectors (see Figure 11). The first

detector will set bit 6 of the Status Register for as long as a valid signal is detected, the second detector

sets bit 7, and bit 10 of the Status Register will be set when both tones are detected.

The Call Progress detector measures the amplitude of the signal at the output of a 275 - 665 Hz

bandpass filter and sets bit 10 of the Status Register to 1 when the signal level exceeds the

measurement threshold.

-60

-50

-40

-30

-20

-10

00.5 11.5 22.5 33.5 4

kHz

Figure 6a Response of Call Progress Filter

The Answer Tone detector measures both amplitude and frequency of the received signal and sets bit 6

or bit 7 of the Status Register when a valid 2225Hz or 2100Hz signal is received.

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 15 D/867/5

1.5.7 Rx Modem Filterering and Demodulation

When the receive part of the CMX867 is operating as a modem, the received signal is fed to a bandpass

filter to attenuate unwanted signals and to provide fixed compromise line equalisation for 600 and

1200bps FSK and DPSK modes. The characteristics of the bandpass filter and equaliser are determined

by the chosen receive modem type and frequency band. The line equaliser may be enabled or disabled

by bit 10 of the General Control Register and compensates for one quarter of the relative amplitude and

delay distortion of ETS Test Line 1.

The responses of these filters, including the line equaliser and the effect of external components used in

Figures 4a and 4b, are shown in Figures 6b-e:

-60

-50

-40

-30

-20

-10

00.5 11.5 22.5 33.5 4

kHz

-60

-50

-40

-30

-20

-10

00.5 11.5 22.5 33.5 4

kHz

Figure 6b DPSK Rx Filters Figure 6c V.21 Rx Filters

-60

-50

-40

-30

-20

-10

00.5 11.5 22.5 33.5 4

kHz

-60

-50

-40

-30

-20

-10

00.5 11.5 22.5 33.5 4

kHz

Figure 6d Bell 103 Rx Filters Figure 6e V.23/Bell 202 Rx Filters

The signal level at the output of the Receive Modem Filter and Equaliser is measured in the Modem

Energy Detector block, compared to a threshold value, and the result controls bit 10 of the Status

The output of the Receive Modem Filter and Equaliser is also fed to the FSK or DPSK demodulator

depending on the selected modem type.

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 16 D/867/5

The FSK demodulator recognises individual frequencies as representing received ‘1’ or ‘0’ data bits:

The DPSK demodulator decodes DPSK modulation of a 1200Hz or 2400Hz carrier and is used for V.22

and Bell 212A modes. It includes an adaptive receive signal equaliser (auto-equaliser) that will

automatically compensate for a wide range of line conditions in DPSK modes. The auto-equaliser can

provide a useful improvement in performance in 600 or 1200bps DPSK modes, so although it must be

disabled at the start of a handshake sequence, it can be enabled as soon as scrambled 1200bps 1s have

been detected.

Both FSK and DPSK demodulators produce a serial data bit stream which is fed to the Rx pattern

detector, descrambler and USART block, see Figure 7a. The demodulator input is also monitored for

continuous dibits '00,11' in 1200bps DPSK mode and continuous alternating 1s and 0s in all other modes.

The DPSK demodulator also estimates the received bit error rate by comparing the actual received signal

against an ideal waveform. This estimate is placed in bits 2-0 of the Status Register, see Figure 10.

1.5.8 Rx Modem Pattern Detectors and Descrambler

See Figure 7a.

The 1010.. pattern detector operates only in FSK modes and will set bit 9 of the Status Register when 32

bits of alternating 1’s and 0’s have been received.

The ‘Continuous Unscrambled 1’s’ detector operates in all modem modes and sets bits 8 and 7 of the

Status Register to ‘01’ when 32 consecutive 1’s have been received.

The descrambler operates only in DPSK modes and is enabled by setting bit 7 of the Rx Mode Register.

The ‘Continuous Scrambled 1’s’ detector operates only in DPSK modes when the descrambler is enabled

and sets bits 8 and 7 of the Status Register to ‘11’ when 32 consecutive 1’s appear at the output of the

descrambler. To avoid possible ambiguity, the ‘Scrambled 1’s’ detector is disabled when continuous

unscrambled 1’s are detected.

The ‘Continuous 0’s’ detector sets bits 8 and 7 of the Status Register to ‘10’ when NX consecutive 0’s

have been received, NX being 32 except when DPSK Start-Stop mode has been selected, in which case

NX = 2N + 4 where N is the number of bits per character including the Start, Stop and any Parity bits.

All of these pattern detectors will hold the ‘detect’ output for 12 bit times after the end of the detected

pattern unless the received bit rate or operating mode is changed, in which case the detectors are reset

within 2 msec.

1.5.9 Rx Data Register and USART

A flexible Rx USART is provided for all modem modes, meeting the requirements of V.14 for DPSK

modems. It can be programmed to treat the received data bit stream as Synchronous data or as Start-

Stop characters.

In Synchronous mode the received data bits are all fed into the Rx Data Buffer which is copied into the

C-BUS Rx Data Register after every 8 bits.

In Start-Stop mode the USART Control logic looks for the start of each character, then feeds only the

required number of data bits (not parity) into the Rx Data Buffer. The parity bit (if used) and the presence

of a Stop bit are then checked and the data bits in the Rx Data Buffer copied to the C-BUS Rx Data

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 17 D/867/5

Figure 7a Rx Modem Data Paths

Whenever a new character is copied into the C-BUS Rx Data Register, the Rx Data Ready flag bit of the

Status Register is set to ‘1’ to prompt the µC to read the new data and, in Start-Stop mode, the Even Rx

Parity flag bit of the Status Register is updated.

In Start-Stop mode, if the Stop bit is missing (received as a ‘0’ instead of a ‘1’) the received character will

still be placed into the Rx Data Register and the Rx Data Ready flag bit set, but, unless allowed by the

V.14 overspeed option described below, the Status Register Rx Framing Error bit will also be set to ‘1’

and the USART will re-synchronise onto the next ‘1’ – ‘0’ (Stop – Start) transition. The Rx Framing Error

bit will remain set until the next character has been received.

Figure 7b Rx USART Function (Start-Stop mode, 8 Data Bits + Parity)

If the µC has not read the previous data from the Rx Data Register by the time that new data is copied to

it from the Rx Data Buffer then the Rx Data Overflow flag bit of the Status Register will be set to 1.

The Rx Data Ready flag and Rx Data Overflow bits are cleared to 0 when the Rx Data Register is read

by the µC.

For DPSK Start-Stop modes, V.14 requires that the receive USART be able to cope with missing Stop

bits; up to 1 missing Stop bit in every 8 consecutive received characters being allowed for the +1%

overspeed (basic signalling rate) V.14 mode and 1 in 4 for the +2.3% overspeed (extended signalling

rate) mode.

To accommodate the requirements of V.14, the CMX867 Rx Mode Register can be set for 0, +1% or

+2.3% overspeed operation in DPSK Start-Stop modes. Missing Stop bits beyond those allowed by the

selected overspeed option will set the Rx Framing Error flag bit of the Status Register.

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 18 D/867/5

In order that received Break signals can be handled correctly in V.14 Rx overspeed mode, a received

character which has all bits ‘0’, including the Stop and any Parity bits, will always cause the Rx Framing

Error bit to be set and the USART to re-synchronise onto the next ‘1’ – ‘0’ transition. Additionally the

received Continuous 0s detector will respond when more than 2M + 3 consecutive ‘0’s are received,

where ‘M’ is the selected total number of bits per character including Stop and any Parity bits.

1.5.10 C-BUS Interface

This block provides for the transfer of data and control or status information between the CMX867’s

internal registers and the µC over the C-BUS serial bus. Each transaction consists of a single Register

Address byte sent from the µC which may be followed by a one or more data byte(s) sent from the µC to

be written into one of the CMX867’s Write Only Registers, or a one or more byte(s) of data read out from

one of the CMX867’s Read Only Registers, as illustrated in Figure 8.

Data sent from the µC on the Command Data line is clocked into the CMX867 on the rising edge of the

Serial Clock input. Reply Data sent from the CMX867 to the µC is valid when the Serial Clock is high.

The CSN line must be held low during a data transfer and kept high between transfers. The C-BUS

interface is compatible with most common µC serial interfaces and may also be easily implemented with

general purpose µC I/O pins controlled by a simple software routine. Figure 14 gives detailed C-BUS

timing requirements.

The following C-BUS addresses and registers are used by the CMX867:

General Reset Command (address only, no data). Address $01

General Control Register, 16-bit write only. Address $E0

Transmit Mode Register, 16-bit write-only. Address $E1

Receive Mode Register, 16-bit write-only. Address $E2

Transmit Data Register, 8-bit write only. Addresses $E3 and $E4

Receive Data Register, 8-bit read-only. Address $E5

Status Register, 16-bit read-only. Address $E6

Programming Register, 16-bit write-only. Address $E8

Note: The C-BUS addresses $E9, $EA and $EB are allocated for production testing and should not be

accessed in normal operation.

1.5.10.1 General Reset Command

General Reset Command (no data) C-BUS address $01

This command resets the device and clears all bits of the General Control , Transmit Mode and Receive

Mode Registers and bits 15 and 13-0 of the Status Register.

Whenever power is applied to the CMX867 a General Reset command should be sent to the device, after

which the General Control Register should be set as required.

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 19 D/867/5

Figure 8 C-BUS Transactions

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 20 D/867/5

1.5.10.2 General Control Register

General Control Register: 16-bit write-only. C-BUS address $E0

This register controls general features of the CMX867 such as the Powersave and Loopback modes, the

IRQ mask bits and the Relay Drive output. It also allows the fixed compromise equalisers in the Tx and

Rx signal paths to be disabled if desired, and sets the internal clock dividers to use either a 11.0592 or a

12.288 MHz XTAL frequency.

All bits of this register are cleared to 0 by a General Reset command.

Bit: 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

0 0 0 Xtal

freq LB Equ Rly

drv Pwr Rst Irqn

en IRQ Mask Bits

General Control Register b15-13: Reserved, set to 000

General Control Register b12: Xtal frequency

This bit should be set according to the Xtal frequency.

b12 = 1 11.0592MHz

b12 = 0 12.2880MHz

General Control Register b11: Analogue Loopback test mode

This bit controls the analogue loopback test mode. Note that in loopback test mode both

Transmit and Receive Mode Registers should be set to the same modem type and band or bit

rate.

b11 = 1 Local analogue loopback mode enabled

b11 = 0 No loopback (normal modem operation)

General Control Register b10: Tx and Rx Fixed Compromise Equalisers

This bit allows the Tx and Rx fixed compromise equalisers in the modem transmit and receive

filter blocks to be disabled.

b10 = 1 Disable equalisers

b10 = 0 Enable equalisers (600 or 1200bps modem modes)

General Control Register b9: Relay Drive

This bit directly controls the RDRVN output pin.

b9 = 1 RDRVN output pin pulled to VSS

b9 = 0 RDRVN output pin pulled to VDD

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 21 D/867/5

General Control Register b8: Powerup

This bit controls the internal power supply to most of the internal circuits, including the Xtal

oscillator and VBIAS supply. Note that the General Reset command clears this bit, putting the

device into Powersave mode.

b8 = 1 Device powered up normally

b8 = 0 Powersave mode (all circuits except Ring Detect, RDRVN and C-BUS

interface disabled)

When the power is first applied to the device, the following powerup procedure should be

followed to ensure correct operation.

i. (Power is applied to the device)

ii. Issue a General Reset command

iii. Write to the General Control Register (address $E0) setting both the Powerup bit

(b8) and the Reset bit (b7) to 1 – leave in this state for a minimum of about 20ms –

it is required that the crystal initially runs for this time in order to clock the internal

logic into a defined state. The device is now powered up, with the crystal and VBIAS

supply operating, but is otherwise not running any transmit or receive functions.

iv. The device is now ready to be programmed as and when required. Examples:

• A General Reset command could be issued to clear all the registers and

therefore powersave the device.

• The Reset bit in the General Control Register could be set to 0 as part of a

routine to program all the relevant registers for setting up a particular operating

mode.

When the device is switched from Powersave mode to normal operation by setting the

Powerup bit to 1, the Reset bit should also be set to 1 and should be held at 1 for about 20ms

while the internal circuits, Xtal oscillator and VBIAS stabilise before starting to use the transmitter

or receiver.

General Control Register b7: Reset

Setting this bit to 1 resets the CMX867’s internal circuitry, clearing all bits of the Transmit and

Receive Mode Registers and b13-0 of the Status Register.

b7 = 1 Internal circuitry in a reset condition.

b7 = 0 Normal operation

General Control Register b6: IRQNEN (IRQN O/P Enable)

Setting this bit to 1 enables the IRQN output pin.

b6 = 1 IRQN pin driven low (to VSS) if the IRQ bit of the Status Register = 1

b6 = 0 IRQN pin disabled (high impedance)

General Control Register b5-0: IRQ Mask bits

These bits affect the operation of the IRQ bit of the Status Register as described in section

1.5.10.7

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 22 D/867/5

1.5.10.3 Transmit Mode Register

Transmit Mode Register: 16-bit write-only. C-BUS address $E1

This register controls the CMX867 transmit signal type and level. All bits of this register are cleared to 0

by a General Reset command, or when b7 (Reset) of the General Control Register is 1.

Bit: 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

Tx mode = modem Tx level Guard tone Scrambler Start-stop /

synch data # data bits /

synch data source

Tx mode = DTMF/Tones Tx level DTMF Twist DTMF or Tone select

Tx mode = Disabled Set to 0000 0000 0000

Tx Mode Register b15-12: Tx mode

These 4 bits select the transmit operating mode.

b15 b14 b13 b12

1 1 1 1 Transmitter disabled (Reserved for future use)

1 1 1 0 Transmitter disabled (Reserved for future use)

1 1 0 1 V.22/Bell 212A 1200 bps DPSK High band (Answering modem)

1 1 0 0 “ Low band (Calling modem)

1 0 1 1 V.22 600 bps DPSK High band (Answering modem)

1 0 1 0 “ Low band (Calling modem)

1 0 0 1 V.21 300 bps FSK High band (Answering modem)

1 0 0 0 “ Low band (Calling modem)

0 1 1 1 Bell 103 300 bps FSK High band (Answering modem)

0 1 1 0 “ Low band (Calling modem)

0 1 0 1 V.23 FSK 1200 bps

0 1 0 0 “ 75 bps

0 0 1 1 Bell 202 FSK 1200 bps

0 0 1 0 “ 150 bps

0 0 0 1 DTMF / Tones

0 0 0 0 Transmitter disabled

Tx Mode Register b11-9: Tx level

These 3 bits set the gain of the Tx Level Control block.

b11 b10 b9

1 1 1 0dB

1 1 0 -1.5dB

1 0 1 -3.0dB

1 0 0 -4.5dB

0 1 1 -6.0dB

0 1 0 -7.5dB

0 0 1 -9.0dB

0 0 0 -10.5dB

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 23 D/867/5

Tx Mode Register b7-5: DTMF Twist (DTMF mode)

These 3 bits allow for adjustment of the DTMF twist to compensate for the frequency

response of different external circuits. Set b8 to 0. The device varies the twist by making

changes to the upper tone group levels. Note that the twist cannot be adjusted mid-tone.

b7 b6 b5

0 0 0 +2.0dB twist (normal setting when external response is flat)

0 0 1 +1.0dB twist

0 1 0 +1.5dB twist

0 1 1 +2.5dB twist

1 0 0 +3.0dB twist

1 0 1 +3.5dB twist

1 1 0 +4.0dB twist

1 1 1 +4.5dB twist (do not use in conjunction with the 0dB tx level

setting).

Tx Mode Register b6-5: Tx Scrambler (DPSK modes)

These 2 bits control the operation of the Tx scrambler used in DPSK modes. Set both

bits to 0 in FSK modes.

b6 b5

1 1 Scrambler enabled, 64 ones detect circuit enabled (normal use)

1 0 Scrambler enabled, 64 ones detect circuit disabled

0 x Scrambler disabled

Tx Mode Register b4-3: Tx Data Format (DPSK and FSK modes)

These two bits select Synchronous or Start-stop mode and the addition of a parity bit to

transmitted characters in Start-stop mode.

b4 b3

1 1 Synchronous mode

1 0 Start-stop mode, no parity

0 1 Start-stop mode, even parity bit added to data bits

0 0 Start-stop mode, odd parity bit added to data bits

Tx Mode Register b2-0: Tx Data and Stop bits (DPSK and FSK: Start-Stop modes)

In Start-stop mode these three bits select the number of Tx data and stop bits.

b2 b1 b0

1 1 1 8 data bits, 2 stop bits

1 1 0 8 data bits, 1 stop bit

1 0 1 7 data bits, 2 stop bits

1 0 0 7 data bits, 1 stop bit

0 1 1 6 data bits, 2 stop bits

0 1 0 6 data bits, 1 stop bit

0 0 1 5 data bits, 2 stop bits

0 0 0 5 data bits, 1 stop bit

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 24 D/867/5

Tx Mode Register b2-0: Tx Data source (DPSK and FSK: Synchronous mode)

In Synchronous mode (b4-3 = 11) these three bits select the source of the data fed to the Tx

FSK or DPSK scrambler and modulator.

b2 b1 b0

1 x x Data bytes from Tx Data Buffer

0 1 1 Continuous 1s

0 1 0 Continuous 0s

0 0 x Continuous dibits ’00,11’ in 1200bps DPSK mode, continuous

alternating 1s and 0s in all other modes.

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 25 D/867/5

Tx Mode Register b8-0: DTMF/Tones mode

If DTMF/Tones transmit mode has been selected (Tx Mode Register b15-12 = 0001) then b8-5

should be set to 0000 and b4-0 will select a DTMF signal or a fixed tone or one of four

programmed tones or tone pairs for transmission.

b4 = 0: Tx fixed tone or programmed tone pair

b3 b2 b1 b0 Tone frequency (Hz)

0 0 0 0 No tone

0 0 0 1 697

0 0 1 0 770

0 0 1 1 852

0 1 0 0 941

0 1 0 1 1209

0 1 1 0 1336

0 1 1 1 1477

1 0 0 0 1633

1 0 0 1 1300 (Calling tone)

1 0 1 0 2100 (Answer tone)

1 0 1 1 2225 (Answer tone)

1 1 0 0 Tone pair TA Programmed Tx tone or tone pair, see 1.5.10.8

1 1 0 1 Tone pair TB “

1 1 1 0 Tone pair TC “

1 1 1 1 Tone pair TD “

b4 = 1: Tx DTMF

b3 b2 b1 b0 Low frequency (Hz) High frequency (Hz) Keypad symbol

0 0 0 0 941 1633 D

0 0 0 1 697 1209 1

0 0 1 0 697 1336 2

0 0 1 1 697 1477 3

0 1 0 0 770 1209 4

0 1 0 1 770 1336 5

0 1 1 0 770 1477 6

0 1 1 1 852 1209 7

1 0 0 0 852 1336 8

1 0 0 1 852 1477 9

1 0 1 0 941 1336 0

1 0 1 1 941 1209 *

1 1 0 0 941 1477 #

1 1 0 1 697 1633 A

1 1 1 0 770 1633 B

1 1 1 1 852 1633 C

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 26 D/867/5

1.5.10.4 Receive Mode Register

Receive Mode Register: 16-bit write-only. C-BUS address $E2

This register controls the CMX867 receive signal type and level.

All bits of this register are cleared to 0 by a General Reset command, or when b7 (Reset) of the General

Control Register is 1.

Bit: 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

Rx mode = modem Rx level Eq Descrambl Start-stop/Synch No. of bits and

parity

Rx mode = Tones detect Rx level DTMF/Tones/Call Progress select

Rx mode = Disabled Set to 0000 0000 0000

Rx Mode Register b15-12: Rx mode

These 4 bits select the receive operating mode.

b15 b14 b13 b12

1 1 1 1 Receiver disabled (Reserved for future use)

1 1 1 0 Receiver disabled (Reserved for future use)

1 1 0 1 V.22/Bell 212A 1200 bps DPSK High band (Calling modem)

1 1 0 0 “ Low band (Answering modem)

1 0 1 1 V.22 600 bps DPSK High band (Calling modem)

1 0 1 0 “ Low band (Answering modem)

1 0 0 1 V.21 300 bps FSK High band (Calling modem)

1 0 0 0 “ Low band (Answering modem)

0 1 1 1 Bell 103 300 bps FSK High band (Calling modem)

0 1 1 0 “ Low band (Answering modem)

0 1 0 1 V.23 FSK 1200 bps

0 1 0 0 “ 75 bps

0 0 1 1 Bell 202 FSK 1200 bps

0 0 1 0 “ 150 bps

0 0 0 1 DTMF, Programmed tone pair, Answer Tone, Call Progress detect

0 0 0 0 Receiver disabled

Rx Mode Register b11-9: Rx level

These three bits set the gain of the Rx Gain Control block.

b11 b10 b9

1 1 1 0dB

1 1 0 -1.5dB

1 0 1 -3.0dB

1 0 0 -4.5dB

0 1 1 -6.0dB

0 1 0 -7.5dB

0 0 1 -9.0dB

0 0 0 -10.5dB

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 27 D/867/5

Rx Mode Register b8: Rx Auto-equalise (DPSK modes)

This bit controls the operation of the receive DPSK auto-equaliser. Set to 0 in FSK modes.

b8 = 1 Enable auto-equaliser

b8 = 0 DPSK mode: Auto-equaliser disabled

Rx Mode Register b7-6: Rx Scrambler (DPSK modes)

These 2 bits control the operation of the Rx descrambler used in DPSK modes. Set

both bits to 0 in FSK modes

b7 b6

1 1 Descrambler enabled, 64 ones detect circuit enabled (normal use)

1 0 Descrambler enabled, 64 ones detect circuit disabled

0 x Descrambler disabled

Rx Mode Register b5-3: Rx USART Setting (DPSK and FSK modes)

These three bits select the Rx USART operating mode. The 1% and 2.3% overspeed options

apply to DPSK modes only.

b5 b4 b3

1 1 1 Rx Synchronous mode

1 1 0 Rx Start-stop mode, no overspeed

1 0 1 Rx Start-stop mode, +1% overspeed (1 in 8 missing Stop bits allowed)

1 0 0 Rx Start-stop mode, +2.3% overspeed (1 in 4 missing Stop bits allowed)

0 x x Rx USART function disabled

Rx Mode Register b2-0: Rx Data bits and parity (DPSK and FSK: Start-Stop modes)

In Start-stop mode these three bits select the number of data bits (plus any parity bit) in each

received character. These bits are ignored in Synchronous mode.

b2 b1 b0

1 1 1 8 data bits + parity

1 1 0 8 data bits

1 0 1 7 data bits + parity

1 0 0 7 data bits

0 1 1 6 data bits + parity

0 1 0 6 data bits

0 0 1 5 data bits + parity

0 0 0 5 data bits

Rx Mode Register b2-0: Tones Detect mode

In Tones Detect Mode (Rx Mode Register b15-12 = 0001) b8-3 should be set to 000000

Bits 2-0 select the detector type.

b2 b1 b0

1 0 0 Programmable Tone Pair Detect

0 1 1 Call Progress Detect

0 1 0 2100, 2225Hz Answer Tone Detect

0 0 1 DTMF Detect

0 0 0 Disabled

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 28 D/867/5

1.5.10.5 Tx Data Register

Tx Data Register: 8-bit write-only. C-BUS addresses $E3 and $E4

Bit: 7 6 5 4 3 2 1 0

Data bits to be transmitted

In Synchronous Tx data mode this register contains the next 8 data bits to be transmitted. Bit 0 is

transmitted first.

In Tx Start-Stop mode the specified number of data bits will be transmitted from this register (b0 first). A

Start bit, a Parity bit (if required) and Stop bit(s) will be added automatically.

This register should only be written to when the Tx Data Ready bit of the Status Register is 1.

C-BUS address $E3 should normally be used, $E4 is for implementing the V.14 overspeed transmission

requirement in Start-Stop mode, see section 1.5.1.

1.5.10.6 Rx Data Register

Rx Data Register: 8-bit read-only. C-BUS address $E5

Bit: 7 6 5 4 3 2 1 0

Received data bits

In unformatted Rx data mode this register contains 8 received data bits, b0 of the register holding the

earliest received bit, b7 the latest.

In Rx Start-Stop data mode this register contains the specified number of data bits from a received

character, b0 holding the first received bit.

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 29 D/867/5

1.5.10.7 Status Register

Status Register: 16-bit read-only. C-BUS address $E6

Bits 13-0 of this register are cleared to 0 by a General Reset command, or when b7 (Reset) of the

General Control Register is 1.

Bit: 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

IRQ RD PF See below for uses of these bits

The meanings of the Status Register bits 12-0 depend on whether the receive circuitry is in Modem or

Tones Detect mode.

Status Register bits:

Rx Modem modes Rx Tones Detect modes ** IRQ

Mask bit

b15 IRQ

b14 Set to 1 on Ring Detect b5

b13 Programming Flag bit. See 1.5.10.8 b4

b12 Set to 1 on Tx data ready.

Cleared by write to Tx Data Register b3

b11 Set to 1 on Tx data underflow.

Cleared by write to Tx Data Register b3

b10 1 when energy is detected in Rx

modem signal band 1 when energy is detected in Call

Progress band or when both

programmable tones are detected

b9 1 when double DPSK dibit 00,11

pattern is detected in 1200bps

DPSK mode, or when ‘1010..’

pattern is detected in all other

modes

0 b1

b8 See following table 0 b1

b7 See following table 1 when 2100Hz answer tone or the

second programmable tone is

detected

b6 Set to 1 on Rx data ready.

Cleared by read from Rx Data

1 when 2225Hz answer tone or the

first programmable tone is detected b0

b5 Set to 1 on Rx data overflow.

Cleared by read from Rx Data

1 when DTMFcode is detected b0

b4 Set to 1 on Rx framing error 0 -

b3 Set to 1 on even Rx parity Rx DTMF code b3, see table -

b2 DPSK Rx signal quality b2 Rx DTMF code b2 -

b1 DPSK Rx signal quality b1 Rx DTMF code b1 -

b0 DPSK Rx signal quality b0

or FSK frequency demodulator

output

Rx DTMF code b0 -

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 30 D/867/5

Notes: ** This column shows the corresponding IRQ Mask bits in the General Control Register. A 0 to 1

transition on any of the Status Register bits 14-5 will cause the IRQ bit b15 to be set to 1 if the

corresponding IRQ Mask bit is 1. The IRQ bit is cleared by a read of the Status Register or a

General Reset command or by setting b7 or b8 of the General Control Register to 1.

The operation of the data demodulator and pattern detector circuits within the CMX867 does not

depend on the state of the Rx energy detect function.

Decoding of Status Register b8,7 in Rx Modem Modes, see also Figure 7a

b8 b7 Descrambler disabled Descrambler enabled

(DPSK modes only)

1 1 - Continuous scrambled 1s

(see note)

1 0 Continuous unscrambled 0s Continuous scrambled 0s

0 1 Continuous unscrambled 1s Continuous unscrambled 1s

0 0 - -

When the descrambler is enabled then detection of continuous unscrambled 1s will inhibit the

continuous scrambled 1s detector.

Figure 9a Operation of Status Register bits 5-10

The IRQN output pin will be pulled low (to VSS) when the IRQ bit of the Status Register and the

IRQNEN bit (b6) of the General Control Register are both 1.

Changes to Status Register bits caused by a change of Tx or Rx operating mode can take up to

150µs to take effect.

In Powersave mode or when the Reset bit (b7) of the General Control Register is 1 the Ring

Detect bit (b14) continues to operate.

The ‘continuous 0’ and ‘continuous 1’ detectors monitor the Rx signal after the DPSK

descrambler, (see Figure 7a) and hence will detect continuous 1s or 0s if the descrambler is

disabled, or continuous scrambled 1s or 0s if the descrambler is enabled.

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 31 D/867/5

In DPSK Rx modem modes b2-0 of the Status Register contain a value indicative of the received

signal BER, see Figure 10. In Rx FSK modem modes bits 2 and 1 will be zero and b0 will show

the output of the frequency demodulator, updated at 8 times the nominal data rate.

Figure 9b Operation of Status Register in DTMF Rx Mode

b3 b2 b1 b0 Low frequency (Hz) High frequency

(Hz) Keypad symbol

0 0 0 0 941 1633 D

0 0 0 1 697 1209 1

0 0 1 0 697 1336 2

0 0 1 1 697 1477 3

0 1 0 0 770 1209 4

0 1 0 1 770 1336 5

0 1 1 0 770 1477 6

0 1 1 1 852 1209 7

1 0 0 0 852 1336 8

1 0 0 1 852 1477 9

1 0 1 0 941 1336 0

1 0 1 1 941 1209 *

1 1 0 0 941 1477 #

1 1 0 1 697 1633 A

1 1 1 0 770 1633 B

1 1 1 1 852 1633 C

Received DTMF Code: b3-0 of Status Register

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 32 D/867/5

1.E-06

1.E-05

1.E-04

1.E-03

01234567

Rx Status Register BER reading

BER

Figure 10 Typical Rx BER vs. Average Status Register BER Reading (b2-0)

1.5.10.8 Programming Register

Programming Register : 16-bit write-only. C-BUS address $E8

This register is used to program the transmit and receive programmed tone pairs by writing appropriate

values to RAM locations within the CMX867. Note that these RAM locations are cleared by Powersave or

Reset.

The Programming Register should only be written to when the Programming Flag bit (b13) of the Status

programming action has been completed (normally within 150µs) the CMX867 will set the bit back to 1.

When programming Transmit or Receive Tone Pairs, do not change the Transmit or Receive Mode

Registers until programming is complete and the Programming Flag bit has returned to 1.

Transmit Tone Pair Programming

4 transmit tone pairs (TA to TD) can be programmed.

The frequency (max 3.4kHz) and level must be entered for each tone to be used.

Single tones are programmed by setting both level and frequency values to zero for one of the pair.

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 33 D/867/5

Programming is done by writing a sequence of up to seventeen 16-bit words to the Programming

The first word should be 32768 (8000 hex), the following 16-bit words set the frequencies and levels and

are in the range 0 to 16383 (0-3FFF hex)

Word Tone Pair Value written

1 32768

2 TA Tone 1 frequency

3 TA Tone 1 level

4 TA Tone 2 frequency

5 TA Tone 2 level

6 TB Tone 1 frequency

7 TB Tone 1 level

- - - - - - - - - - - - - - - -

16 TD Tone 2 frequency

17 TD Tone 2 level

The Frequency values to be entered are calculated from the formula:

Value to be entered = desired frequency (Hz) * 3.414

i.e. for 1kHz the value to be entered is 3414 (or 0D56 in Hex).

The Level values to be entered are calculated from the formula:

Value to be entered = desired Vrms * 93780 / VDD

i.e. for 0.5Vrms at VDD = 3.0V, the value to be entered is 15630 (3D0E in Hex)

Note that allowance should be made for the transmit signal filtering in the CMX867 which attenuates the

output signal for frequencies above 2kHz by 0.25dB at 2.5kHz, by 1dB at 3kHz and by 2.2dB at 3.4kHz.

On powerup or after a reset, the tone pairs TA-TC are set to notone, and TD set to generate 2130Hz +

2750Hz at approximately –20dBm each.

Receive Tone Pair Programming

The programmable tone pair detector is implemented as shown in Figure 11a. The filters are 4th order IIR

sections. The frequency detectors measure the time taken for a programmable number of complete input

signal cycles and compare this time against programmable upper and lower limits.

Figure 11a Programmable Tone Detectors

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 34 D/867/5

Figure 11b Filter Implementation

Programming is done by writing a sequence of twenty-seven 16-bit words to the Programming Register.

The first word should be 32769 (8001 hex), the following twenty-six 16-bit words set the frequencies and

levels and are in the range 0 to 32767 (0000-7FFF hex).

Word Value written Word Value written

1 32769

2 Filter #1 coefficient b21 15 Filter #2 coefficient b21

3 Filter #1 coefficient b11 16 Filter #2 coefficient b11

4 Filter #1 coefficient b01 17 Filter #2 coefficient b01

5 Filter #1 coefficient a21 18 Filter #2 coefficient a21

6 Filter #1 coefficient a11 19 Filter #2 coefficient a11

7 Filter #1 coefficient b22 20 Filter #2 coefficient b22

8 Filter #1 coefficient b12 21 Filter #2 coefficient b12

9 Filter #1 coefficient b02 22 Filter #2 coefficient b02

10 Filter #1 coefficient a22 23 Filter #2 coefficient a22

11 Filter #1 coefficient a12 24 Filter #2 coefficient a12

12 Freq measurement #1 ncycles 25 Freq measurement #2 ncycles

13 Freq measurement #1 mintime 26 Freq measurement #2 mintime

14 Freq measurement #1 maxtime 27 Freq measurement #2 maxtime

The coefficients are entered as 15-bit signed (two’s complement) integer values (the most significant bit

of the 16-bit word entered should be zero) calculated as 8192 * coefficient value from the user’s filter

design program (i.e. this allows for filter design values of -1.9999 to +1.9999).

The design of the IIR filters should make allowance for the fixed receive signal filtering in the CMX867

which has a low pass characteristic above 1.5kHz of 0.4dB at 2kHz, 1.2dB at 2.5kHz, 2.6dB at 3kHz and

4.1dB at 3.4kHz.

‘ncycles’ is the number of signal cycles for the frequency measurement.

‘mintime’ is the smallest acceptable time for ncycles of the input signal expressed as the number of

9.6kHz timer clocks. i.e. ‘mintime’ = 9600 * ncycles / high frequency limit

‘maxtime’ is the highest acceptable time for ncycles of the input signal expressed as the number of

9.6kHz timer clocks. i.e. ‘maxtime’ = 9600 * ncycles / low frequency limit

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 35 D/867/5

The level detectors include hysteresis. The threshold levels - measured at the 2 or 4-wire line with unity

gain filters, using the line interface circuits described in section 1.4.2, 1.0 dB line coupling transformer

loss and with the Rx Gain Control block set to 0dB - are nominally:

‘Off’ to ‘On’ -44.5dBm

‘On’ to ‘Off’ -47.0dBm

Note that if any changes are made to the programmed values while the CMX867 is running in

Programmed Tone Detect mode they will not take effect until the CMX867 is next switched into

Programmed Tone Detect mode.

On powerup or after a reset, the programmable tone pair detector is set to act as a simple 2130Hz +

2750Hz detector.

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 36 D/867/5

1.6 Application Notes

1.6.1 V.22 Calling Modem Application

This section describes how the CMX867 can be used in a V.22 Calling modem application, employing

V.25 automatic answering and the V.22 recommended handshake sequence. This attempts to establish a

1200bps connection.

1. Ensure that the CMX867 is powered up. Set the Tx Mode Register to DTMF/Tones mode (set to ‘No

Tone’ at this time), and the Rx Mode Register to Call Progress Detect mode.

2. Connect the line (go off hook) then dial the required number using the DTMF generator, monitoring

for call progress signals (dial tone, busy, etc). Change to Answer Tone Detect mode.

3. On detection of the 2100Hz answer tone wait for it to end then wait for the 2225Hz answer tone

detector to respond. (The ‘2225Hz’ answer tone detector will recognise unscrambled binary 1s at

1200bps High Band as well as 2225Hz). When unscrambled binary 1s or 2225Hz have been

received for 155ms set a 456ms timer.

4. When the 456ms timer expires check that the 2225Hz or unscrambled 1s is still being received, then

set the Tx Mode Register for V.22 1200bps Low Band transmission of scrambled 1s (continuous 1s

with the scrambler enabled). Also set the Rx Mode register to V.22 1200bps High Band receive,

descrambler enabled and Rx USART disabled.

5. When scrambled 1s (at 1200bps) have been received for 270ms enable the Rx USART, set a

765ms timer and load the Tx Data Register with the first data to be transmitted.

6. When the timer expires set the Tx Mode Register for Start-Stop or Synchronous transmission of

data from the Tx Data Buffer. This will start transmission of the data loaded in step 5.

7. A 1200bps data connection has now been established.

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 37 D/867/5

1.6.2 V.22 Answering Modem Application

This section describes how the CMX867 can be used in a V.22 Answering modem application, employing

V.25 automatic answering and the V.22 recommended handshake sequence. This attempts to establish a

1200 bps connection.

1. It is assumed that the CMX867 will be in Powersave mode, with the Ring Detector circuits

monitoring the line.

2. When a ring signal is detected connect the line (go off hook), set a 2150ms timer and power up the

CMX867, setting the Tx Mode Register to DTMF/Tones mode (set for ‘no tone’ at this time) and the

Rx Mode Register to V.22 1200bps Low Band receive, descrambler enabled, Rx USART disabled.

3. When the 2150ms timer expires set the Tx Mode Register to transmit the 2100Hz answer tone and

set a 3300ms timer.

4. When the 3300ms timer expires set the Tx Mode Register to no tone and set a 75ms timer.

5. When the 75ms timer expires set the Tx Mode Register for V.22 High Band 1200bps transmission of

unscrambled 1s. Monitor the received signal for scrambled 1s.

6. When scrambled 1s have been detected for 270ms, set the Tx Mode Register to V.22 High Band

1200bps scrambled 1s transmission and set a 765ms timer and enable the Rx USART.

7. Load the Tx Data Buffer with the first data to be transmitted.

8. When the 765ms timer expires set the Tx Mode Register for Start-Stop or Synchronous

transmission of data from the Tx Data Buffer. This will start transmission of the data loaded in step

9. A 1200bps data connection has now been established.

1.6.3 Reference Diagrams

The circuit diagrams in the EV8680 and DE8681 kits should be consulted for examples of a complete

telephone line interface. These diagrams are contained in their respective User Manuals, which can be

downloaded from the CML website.

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 38 D/867/5

1.7 Performance Specification

1.7.1 Electrical Performance

1.7.1.1 Absolute Maximum Ratings

Exceeding these maximum ratings can result in damage to the device.

Min. Max. Units

Supply (VDD - VSS) -0.3 7.0 V

Voltage on any pin to VSS -0.3 VDD + 0.3 V

Current into or out of VDD and VSS pins -50 +50 mA

Current into RDRVN pin (RDRVN pin low) +50 mA

Current into or out of any other pin -20 +20 mA

D2 Package Min. Max. Units

Total Allowable Power Dissipation at Tamb = 25°C 1000 mW

... Derating 13 mW/°C

Storage Temperature -55 +125 °C

Operating Temperature -40 +85 °C

E2 Package Min. Max. Units

Total Allowable Power Dissipation at Tamb = 25°C 400 mW

... Derating 5.3 mW/°C

Storage Temperature -55 +125 °C

Operating Temperature -40 +85 °C

P4 Package Min. Max. Units

Total Allowable Power Dissipation at Tamb = 25°C 1000 mW

... Derating 13 mW/°C

Storage Temperature -55 +125 °C

Operating Temperature -40 +85 °C

1.7.1.2 Operating Limits

Correct operation of the device outside these limits is not implied.

Notes Min. Max. Units

Supply (VDD - VSS) 2.7 5.5 V

Operating Temperature -40 +85 °C

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 39 D/867/5

1.7.1.3 Operating Characteristics

For the following conditions unless otherwise specified:

VDD = 2.7V to 5.5V at Tamb = -40 to +85°C,

Xtal Frequency = 11.0592 or 12.288MHz ± 0.01% (100ppm)

0dBm corresponds to 775mVrms.

DC Parameters Notes Min. Typ. Max. Units

IDD (Powersave mode) 1, 2 - 2.0 - µA

(Reset but not powersave, VDD = 3.0V) 1, 3 - 1.7 3.5 mA

(Reset but not powersave, VDD = 5.0V) 1, 3 - 2.5 5.0 mA

(Running, VDD = 3.0V) 1 - 3.0 6.0 mA

(Running, VDD = 5.0V) 1 - 5.5 11.0 mA

Logic '1' Input Level 4 70% - - VDD

Logic '0' Input Level 4 - - 30% VDD

Logic Input Leakage Current (Vin = 0 to VDD),

(excluding XTAL/CLOCK input) -1.0 - +1.0 µA

Output Logic '1' Level (lOH = 2 mA) 80% - - VDD

Output Logic '0' Level (lOL = -3 mA) - - 0.4 V

IRQN O/P 'Off' State Current (Vout = VDD) - - 1.0 µA

RD and RT pin Schmitt trigger input high-going

threshold (Vthi) (see Figure 12) 0.56VDD - 0.56VDD

+ 0.6V V

RD and RT pin Schmitt trigger input low-going

threshold (Vtlo) (see Figure 12) 0.44VDD

- 0.6V - 0.44VDD V

RDRVN ‘ON’ resistance to VSS (VDD= 3.0V) - 50 70 Ω

RDRVN ‘OFF’ resistance to VDD (VDD= 3.0V) - 1300 3000 Ω

XTAL/CLOCK Input

(timings for an external clock input) Notes Min. Typ. Max. Units

'High' Pulse Width 30 - - ns

'Low' Pulse Width 30 - - ns

Notes: 1. At 25°C, not including any current drawn from the CMX867 pins by external circuitry

other than X1, C1 and C2.

2. All logic inputs at VSS except for RT and CSN inputs which are at VDD.

3. General Mode Register b8 and b7 both set to 1.

4. Excluding RD and RT pins.

0.5

1.5

2.5

3.5

2.5 33.5 44.5 55.5

Vdd

Vin

Vthi

Vtlo

Figure 12 Typical Schmitt Trigger Input Voltage Thresholds vs. VDD

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 40 D/867/5

Transmit DPSK Modes

(V.22 and Bell 212A) Notes Min. Typ. Max. Units

Carrier frequency, high band 5 - 2400 - Hz

Carrier frequency, low band 5 - 1200 - Hz

Baud rate 6 - 600 - Baud

Bit rate 6 - 1200/600 - bps

550Hz guard tone frequency 548 550 552 Hz

550Hz guard tone level wrt data signal -4.0 -3.0 -2.0 dB

1800Hz guard tone frequency 1797 1800 1803 Hz

1800Hz guard tone level wrt data signal -7.0 -6.0 -5.0 dB

Transmit V.21 FSK Mode Notes Min. Typ. Max. Units

Baud rate 6 - 300 - Baud

Mark (logical 1) frequency, high band 1647 1650 1653 Hz

Space (logical 0) frequency, high band 1847 1850 1853 Hz

Mark (logical 1) frequency, low band 978 980 982 Hz

Space (logical 0) frequency, low band 1178 1180 1182 Hz

Transmit Bell 103 FSK Mode Notes Min. Typ. Max. Units

Baud rate 6 - 300 - Baud

Mark (logical 1) frequency, high band 2222 2225 2228 Hz

Space (logical 0) frequency, high band 2022 2025 2028 Hz

Mark (logical 1) frequency, low band 1268 1270 1272 Hz

Space (logical 0) frequency, low band 1068 1070 1072 Hz

Transmit V.23 FSK Mode Notes Min. Typ. Max. Units

Baud rate 6 - 1200/75 - Baud

Mark (logical 1) frequency, 1200 baud 1298 1300 1302 Hz

Space (logical 0) frequency, 1200 baud 2097 2100 2103 Hz

Mark (logical 1) frequency, 75 baud 389 390 391 Hz

Space (logical 0) frequency, 75 baud 449 450 451 Hz

Transmit Bell 202 FSK Mode Notes Min. Typ. Max. Units

Baud rate 6 - 1200/150 - Baud

Mark (logical 1) frequency, 1200 baud 1198 1200 1202 Hz

Space (logical 0) frequency, 1200 baud 2197 2200 2203 Hz

Mark (logical 1) frequency, 150 baud 386 387 388 Hz

Space (logical 0) frequency, 150 baud 486 487 488 Hz

DTMF/Single Tone Transmit Notes Min. Typ. Max. Units

Tone frequency accuracy -0.2 - +0.2 %

Distortion 7 - 1.0 2.0 %

Notes: 5. % carrier frequency accuracy is the same as XTAL/CLOCK % frequency accuracy.

6. Tx signal % baud or bit rate accuracy is the same as XTAL/CLOCK % frequency

accuracy.

7. Measured between TXA and TXAN pins with Tx Level Control gain set to 0dB, 1k2Ω load

between TXA and TXAN, at VDD = 3.0V (levels are proportional to VDD - see section

1.4.2). Level measurements for all modem modes are performed with random

transmitted data and without any guard tone. 0dBm = 775mVrms.

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 41 D/867/5

Transmit Output Level Notes Min. Typ. Max. Units

Modem and Single Tone modes 7 -4.0 -3.0 -2.0 dBm

DTMF mode, Low Group tones 7 -2.0 -1.0 0.0 DBm

DTMF twist (level of high group tones wrt

low group) setting accuracy

-1.0

+1.0

Tx output buffer gain control accuracy 7 -0.25 - +0.25 dB

-70

-60

-50

-40

-30

-20

-10

10 100 1000 10000 100000

dBm

Bell 202

Figure 13 Maximum Out of Band Tx Line Energy Limits (see note 8)

Notes: 8. Measured on the 2 or 4-wire line using the line interface circuits described in section

1.4.2 with the Tx line signal level set to -10dBm for DPSK, FSK or single tones, -6dBm

and -8dBm for DTMF tones. Excludes any distortion due to external components such as

the line coupling transformer.

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 42 D/867/5

Receive DPSK Modes

(V.22 and Bell 212A) Notes Min. Typ. Max. Units

Carrier frequency (high band) 2392 2400 2408 Hz

Carrier frequency (low band) 1192 1200 1208 Hz

Baud rate 9 - 600 - Baud

Bit rate 9 - 1200/600 - bps

Receive V.21 FSK Mode Notes Min. Typ. Max. Units

Acceptable baud rate 297 300 303 Baud

Mark (logical 1) frequency, high band 1638 1650 1662 Hz

Space (logical 0) frequency, high band 1838 1850 1862 Hz

Mark (logical 1) frequency, low band 968 980 992 Hz

Space (logical 0) frequency, low band 1168 1180 1192 Hz

Receive Bell 103 FSK Mode Notes Min. Typ. Max. Units

Acceptable baud rate 297 300 303 Baud

Mark (logical 1) frequency, high band 2213 2225 2237 Hz

Space (logical 0) frequency, high band 2013 2025 2037 Hz

Mark (logical 1) frequency, low band 1258 1270 1282 Hz

Space (logical 0) frequency, low band 1058 1070 1082 Hz

Receive V.23 FSK Mode Notes Min. Typ. Max. Units

1200 baud

Acceptable baud rate 1188 1200 1212 Baud

Mark (logical 1) frequency 1280 1300 1320 Hz

Space (logical 0) frequency 2080 2100 2120 Hz

75 baud

Acceptable baud rate 74 75 76 Baud

Mark (logical 1) frequency 382 390 398 Hz

Space (logical 0) frequency 442 450 458 Hz

Receive Bell 202 FSK Mode Notes Min. Typ. Max. Units

1200 baud

Acceptable baud rate 1188 1200 1212 Baud

Mark (logical 1) frequency 1180 1200 1220 Hz

Space (logical 0) frequency 2180 2200 2220 Hz

150 baud

Acceptable baud rate 148 150 152 Baud

Mark (logical 1) frequency 377 387 397 Hz

Space (logical 0) frequency 477 487 497 Hz

Rx Modem Signal

(FSK and DPSK Modes) Notes Min. Typ. Max. Units

Signal level 10 -45 - -9 dBm

Signal to Noise Ratio (noise flat 300-3400Hz) 20 - - dB

Notes: 9. These are the bit and baud rates of the line signal, the acceptable tolerance is ±0.01%.

10. Rx 2 or 4-wire line signal level assuming 1dB loss in line coupling transformer with Rx

Gain Control block set to 0dB and external components as section 1.4.2.

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 43 D/867/5

Rx Modem '0011' Dibit Pattern Detector

(1200bps DPSK mode) Notes Min. Typ. Max. Units

Will detect pattern lasting for 90.0 - - ms

Will not detect pattern lasting for 72.0

Hold time (minimum detector ‘On’ time) 5.0 - - ms

Rx Modem Energy Detector Notes Min. Typ. Max. Units

Detect threshold (‘Off’ to ‘On) 10,11 - - -43.0 dBm

Undetect threshold (‘On’ to ‘Off’) 10,11 -48.0 - - dBm

Hysteresis 10,11 2.0 - - dB

Detect (‘Off’ to ‘On’) response time

DPSK modes 10,11 10.0 - 35.0 ms

300 and 1200 baud FSK modes 10,11 8.0 - 30.0 ms

150 and 75 baud FSK modes 10,11 16.0 - 60.0 ms

Undetect (‘On’ to ‘Off’) response time

DPSK modes 10,11 10.0 - 55.0 ms

300 and 1200 baud FSK modes 10,11 10.0 - 40.0 ms

150 and 75 baud FSK modes 10,11 20.0 - 80.0 ms

Rx Answer Tone Detectors Notes Min. Typ. Max. Units

Detect threshold (‘Off’ to ‘On) 10,12 - - -43.0 dBm

Undetect threshold (‘On’ to ‘Off’) 10,12 -48.0 - - dBm

Hysteresis 10,12 2.0 - - dB

Detect (‘Off’ to ‘On’) response time 10,12 30.0 33.0 45.0 ms

Undetect (‘On’ to ‘Off’) response time 10,12 7.0 18.0 25.0 ms

2100Hz detector

‘Will detect’ frequency 2050 - 2160 Hz

‘Will not detect’ frequency - - 2000 Hz

2225Hz detector

‘Will detect’ frequency 2160 - 2285 Hz

‘Will not detect’ frequency 2335 - - Hz

Rx Call Progress Energy Detector Notes Min. Typ. Max. Units

Bandwidth (-3dB points) See Figure 6a 275 - 665 Hz

Detect threshold (‘Off’ to ‘On) 10,13 - - -37.0 dBm

Undetect threshold (‘On’ to ‘Off’) 10,13 -42.0 - - dBm

Detect (‘Off’ to ‘On’) response time 10,13 30.0 36.0 45.0 ms

Undetect (‘On’ to ‘Off’) response time 10,13 6.0 8.0 50.0 ms

Notes: 11. Thresholds and times measured with random data for DPSK modes, continuous binary

‘1’ for all FSK modes. Fixed compromise line equaliser enabled. Signal switched

between off and -33dBm

12. ‘Typical’ value refers to 2100Hz or 2225Hz signal switched between off and -33dBm.

Times measured wrt. received line signal

13. ‘Typical’ values refers to 400Hz signal switched between off and -33dBm

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 44 D/867/5

DTMF Decoder Notes Min. Typ. Max. Unit

Valid input signal levels

(each tone of composite signal)

-30.0

0.0

dBm

Not decode level

(either tone of composite signal)

-36.0

dBm

Twist = High Tone/Low Tone -10.0 - 6.0 dB

Frequency Detect Bandwidth ±1.8 - - %

Frequency Not Detect Bandwidth - - ±3.5 %

Max level of low frequency noise (i.e dial tone)

Interfering signal frequency <= 550Hz 14 - - 0.0 dB

Interfering signal frequency <= 450Hz 14 - - 10.0 dB

Interfering signal frequency <= 200Hz 14 - - 20.0 dB

Max. noise level wrt. signal 14,15 - - -10.0 dB

DTMF detect response time - - 40.0 ms

DTMF de-response time - - 30.0 ms

Status Register b5 high time 14.0 - - ms

‘Will Detect’ DTMF signal duration 40.0 - - ms

‘Will Not Detect’ DTMF signal duration - 25.0 - ms

Pause length detected 30.0 - - ms

Pause length ignored - - 15.0 ms

Receive Input Amplifier Notes Min. Typ. Max. Units

Input impedance (at 100Hz) 10.0 Moh

Open loop gain (at 100Hz) 10000 V/V

Rx Gain Control Block accuracy -0.25 +0.25 dB

Notes: 14. Referenced to DTMF tone of lower amplitude.

15. Flat Gaussian Noise in 300-3400Hz band.

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 45 D/867/5

C-BUS Timings (See Figure 14) Notes Min. Typ. Max. Units

tCSE CSN-Enable to Clock-High time 100 - - ns

tCSH Last Clock-High to CSN-High time 100 - - ns

tLOZ Clock-Low to Reply Output enable

time 0.0 - - ns

tHIZ CSN-High to Reply Output 3-state

time - - 1.0 µs

tCSOFF CSN-High Time between transactions 1.0 - - µs

tNXT Inter-Byte Time 200 - - ns

tCK Clock-Cycle time 200 - - ns

tCH Serial Clock-High time 100 - - ns

tCL Serial Clock-Low time 100 - - ns

tCDS Command Data Set-Up time 75.0 - - ns

tCDH Command Data Hold time 25.0 - - ns

tRDS Reply Data Set-Up time 50.0 - - ns

tRDH Reply Data Hold time 0.0 - - ns

Maximum 30pF load on each C-BUS interface line.

Note: These timings are for the latest version of the C-BUS as embodied in the CMX867.

Figure 14 C-BUS Timing

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 46 D/867/5

1.7.2 Packaging

Figure 15a 24-pin SOIC (D2) Mechanical Outline: Order as part no. CMX867D2

Figure 15b 24-pin TSSOP (E2) Mechanical Outline: Order as part no. CMX867E2

Low Power V.22 Modem CMX867

 2004 Consumer Microcircuits Limited 47 D/867/5

Figure 15c 24-pin DIL (P4) Mechanical Outline: Order as part no. CMX867P4

Low Power V.22 Modem CMX867

Handling precautions: This product includes input protection, however, precautions should be taken to prevent device damage

from electro-static discharge. CML does not assume any responsibility for the use of any circuitry described. No IPR or circuit

patent licences are implied. CML reserves the right at any time without notice to change the said circuitry and this product

specification. CML has a policy of testing every product shipped using calibrated test equipment to ensure compliance with this

product specification. Specific testing of all circuit parameters is not necessarily performed.

www.cmlmicro.com

For FAQs see: www.cmlmicro.com/products/faqs/

For a full data sheet listing see: www.cmlmicro.com/products/datasheets/download.htm

For detailed application notes: www.cmlmicro.com/products/applications/

Oval Park, Langford, Maldon,

Essex,

CM9 6WG - England.

Tel: +44 (0)1621 875500

Fax: +44 (0)1621 875600

Sales:

sales@cmlmicro.com

Technical Support:

techsupport@cmlmicro.com

4800 Bethania Station Road,

Winston-Salem,

NC 27105 - USA.

Tel: +1 336 744 5050,

800 638 5577

Fax: +1 336 744 5054

Sales:

us.sales@cmlmicro.com

Technical Support:

us.techsupport@cmlmicro.com

No 2 Kallang Pudding Road,

#09 to 05/06 Mactech

Industrial Building,

Singapore 349307

Tel: +65 6745 0426

Fax: +65 6745 2917

Sales:

sg.sales@cmlmicro.com

Technical Support:

sg.techsupport@cmlmicro.com

No. 218, Tian Mu Road

West, Tower 1, Unit 1008,

Shanghai Kerry Everbright

City, Zhabei,

Shanghai 200070,

China.

Tel: +86 21 6317 4107

+86 21 6317 8916

Fax: +86 21 6317 0243

Sales:

cn.sales@cmlmicro.com.cn

Technical Support:

sg.techsupport@cmlmicro.com