MQFL-28-2R5S Single Output H igh R eliability DC/DC C onverter 16-40V Continuous Input 16-50V Transient Input 2.5V 40A Output 88% @ 20A / 87% @ 40A Output F ull P ower O peration : -55C Efficiency to +125C The MilQor(R) series of high-reliability DC/DC converters brings SynQor's field proven high-efficiency synchronous rectifier technology to the Military/Aerospace industry. SynQor's innovative QorSealTM packaging approach ensures survivability in the most hostile environments. Compatible with the industry standard format, these converters operate at a fixed frequency, have no opto-isolators, and follow conservative component derating guidelines. They are designed and manufactured to comply with a wide range of military standards. Design Process Designed & Manufactured in the USA Featuring QorSealTM Hi-Rel Assembly MQFL series converters are: * Designed for reliability per NAVSO-P3641-A guidelines * Designed with components derated per: -- MIL-HDBK-1547A -- NAVSO P-3641A Qualification Process MQFL series converters are qualified to: * MIL-STD-810F -- consistent with RTCA/D0-160E * SynQor's First Article Qualification -- consistent with MIL-STD-883F * SynQor's Long-Term Storage Survivability Qualification * SynQor's on-going life test Features * * * * * * * * Fixed switching frequency No opto-isolators Parallel operation with current share Remote sense Clock synchronization Primary and secondary referenced enable Continuous short circuit and overload protection Input under-voltage lockout/over-voltage shutdown Specification Compliance In-Line Manufacturing Process * * * * * * MQFL series converters (with MQME filter) are designed to meet: * MIL-HDBK-704-8 (A through F) * RTCA/DO-160E Section 16 * MIL-STD-1275B * DEF-STAN 61-5 (part 6)/5 * MIL-STD-461 (C, D, E) * RTCA/DO-160E Section 22 AS9100 and ISO 9001:2000 certified facility Full component traceability Temperature cycling Constant acceleration 24, 96, 160 hour burn-in Three level temperature screening Product # MQFL-28-2R5S Phone 1-888-567-9596 www.synqor.com Doc.# 005-2MQ250S Rev. B 03/19/09 Page 1 MQFL-28-2R5S Output: 2.5 V Current: 40 A Technical Specification BLOCK DIAGRAM TYPICAL CONNECTION DIAGRAM 1 2 3 4 28Vdc + - 5 open means on Product # MQFL-28-2R5S 6 ENA 2 +VIN IN RTN SHARE CASE + SNS ENA 1 - SNS SYNC OUT OUT RTN +VOUT SYNC IN Phone 1-888-567-9596 www.synqor.com 12 11 open means on 10 9 + Load 8 - 7 Doc.# 005-2MQ250S Rev. B 03/19/09 Page 2 MQFL-28-2R5S Output: 2.5 V Current: 40 A Technical Specification MQFL-28-2R5S ELECTRICAL CHARACTERISTICS Parameter Min. Nom. Max. Units Notes & Conditions ABSOLUTE MAXIMUM RATINGS Input Voltage Non-Operating Operating 1 Reverse Bias (Tcase = 125C) Reverse Bias (Tcase = -55C) Isolation Voltage (input/output to case, input to output) Continuous -500 Transient (100 s) -800 Operating Case Temperature 2 -55 Storage Case Temperature -65 Lead Temperature (20 sec) Voltage at ENA1, ENA2, SYNC IN -1.2 INPUT CHARACTERISTICS Operating Input Voltage Range (continuous) 16 28 Operating Input Voltage Range (transient, 1 sec) 16 28 Input Under-Voltage Lockout 3 Turn-On Voltage Threshold 14.75 15.50 Turn-Off Voltage Threshold 13.80 14.40 Lockout Voltage Hysteresis 0.50 1.10 Input Over-Voltage Shutdown 3 Turn-Off Voltage Threshold 54.0 56.8 Turn-On Voltage Threshold 50.0 51.4 Shutdown Voltage Hysteresis 2.0 5.3 Maximum Input Current No Load Input Current (operating) 110 Disabled Input Current (ENA1) 2 Disabled Input Current (ENA2) 25 Input Terminal Current Ripple (peak to peak) 40 OUTPUT CHARACTERISTICS 60 60 -0.8 -1.2 V V V V 500 800 135 135 300 50 V V C C C V 40 50 V V 1, 2, 3 4, 5, 6 16.00 15.00 1.80 V V V 1, 2, 3 1, 2, 3 1, 2, 3 60.0 54.0 8.0 8 160 5 50 60 Output Voltage Set Point (Tcase = 25C) 2.47 2.50 2.53 Output Voltage Set Point Over Temperature 2.46 2.50 2.54 Output Voltage Line Regulation -20 0 20 Output Voltage Load Regulation 7 12 17 Total Output Voltage Range 2.45 2.50 2.55 Output Voltage Ripple and Noise Peak to Peak 15 60 Operating Output Current Range 0 40 Operating Output Power Range 0 100 Output DC Current-Limit Inception 4 41 46 52 Short Circuit Output Current 41 47 53 Back-Drive Current Limit while Enabled 13 Back-Drive Current Limit while Disabled 10 50 Maximum Output Capacitance 10,000 DYNAMIC CHARACTERISTICS Output Voltage Deviation Load Transient 6 For a Positive Step Change in Load Current -450 -300 For a Negative Step Change in Load Current 300 450 Settling Time (either case) 7 200 350 Output Voltage Deviation Line Transient 8 For a Positive Step Change in Line Voltage -250 250 For a Negative Step Change in Line Voltage -250 250 7 Settling Time (either case) 250 500 Turn-On Transient Output Voltage Rise Time 6 10 Output Voltage Overshoot 0 2 Turn-On Delay, Rising Vin 9 11 5.5 8.0 Turn-On Delay, Rising ENA1 11 3.0 6.0 Turn-On Delay, Rising ENA2 11 1.5 3.0 EFFICIENCY Iout = 40A (16Vin) 82 Iout = 20A (16Vin) 86 Iout = 40A (28Vin) 82 Iout = 20A (28Vin) 85 Iout = 40A (40Vin) 81 Iout = 20A (40Vin) 83 Load Fault Power Dissipation Short Circuit Power Dissipation Product # MQFL-28-2R5S Phone 1-888-567-9596 Group A Vin=28V DC 5%, Iout = 40A, CL = 0 F, free running10 Subgroup13 unless otherwise specified 87 89 87 88 86 87 19 34 20 34 V V V A Vin = 16V; Iout = 40A mA mA Vin = 16V, 28V, 50V mA Vin = 16V, 28V, 50V mA Bandwidth = 100 kHz - 10 MHz; see Figure 14 V Vout at sense leads V " mV " ; Vin = 16V, 28V, 50V mV " ; Vout @ (Iout=0A) - Vout @ (Iout=40A) V " mV Bandwidth = 10 MHz; CL=11F A W A A Vout 1.2V A mA F mV Total Iout step = 20A 40A, 4A 20A; CL=11F mV " s 1, 1, 1, 1, 1, 1, 1, 1, 2, 2, 2, 2, 2, 2, 2, 2, 3 3 3 3 3 3 3 3 1 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 See Note 5 1, 2, 3 See Note 5 4, 5, 6 4, 5, 6 4, 5, 6 mV Vin step = 16V 50V; CL=11F mV " s 4, 5, 6 4, 5, 6 See Note 5 ms Vout = 0.25V 2.25V % ms ENA1, ENA2 = 5V ms ENA2 = 5V ms ENA1 = 5V 4, 5, 6 See Note 5 4, 5, 6 4, 5, 6 4, 5, 6 % % % % % % W Iout at current limit inception point W Vout 1.2V www.synqor.com 1, 1, 1, 1, 1, 1, 1, 1, 4 Doc.# 005-2MQ250S Rev. B 03/19/09 2, 2, 2, 2, 2, 2, 2, 2, 3 3 3 3 3 3 3 3 Page 3 MQFL-28-2R5S Output: 2.5 V Current: 40 A Technical Specification MQFL-28-2R5S ELECTRICAL CHARACTERISTICS (Continued) Parameter Min. Nom. Max. Units Notes & Conditions ISOLATION CHARACTERISTICS Isolation Voltage (dielectric strength) Input RTN to Output RTN 500 Any Input Pin to Case 500 Any Output Pin to Case 500 Isolation Resistance (input rtn to output rtn) 100 Isolation Resistance (any pin to case) 100 Isolation Capacitance (input rtn to output rtn) 44 FEATURE CHARACTERISTICS Switching Frequency (free running) 500 550 600 Synchronization Input Frequency Range 500 700 Logic Level High 2 10 Logic Level Low -0.5 0.8 Duty Cycle 20 80 Synchronization Output Pull Down Current 20 Duty Cycle 25 75 Enable Control (ENA1 and ENA2) Off-State Voltage 0.8 Module Off Pulldown Current 80 On-State Voltage 2 Module On Pin Leakage Current 20 Pull-Up Voltage 3.2 4.0 4.5 RELIABILITY CHARACTERISTICS Calculated MTBF (MIL-STD-217F2) GB @ Tcase=70C AIF @ Tcase=70C Demonstrated MTBF 2800 440 TBD Device Weight 79 WEIGHT CHARACTERISTICS Group A Vin=28V DC 5%, Iout = 40A, CL = 0 F, free running10 Subgroup13 unless otherwise specified V V V MW MW nF 1 1 1 1 1 1 kHz 1, 2, 3 kHz V V % 1, 2, 3 1, 2, 3 1, 2, 3 See Note 5 mA % See Note 5 See Note 5 VSYNC OUT = 0.8V Output connected to SYNC IN of another MQFL converter V A Current drain required to ensure module is off V A Maximum current draw from pin allowed with module still on V See Figure A 1, 2, 3 See Note 5 1, 2, 3 See Note 5 1, 2, 3 103 Hrs. 103 Hrs. 103 Hrs. g Electrical Characteristics Notes 1. Converter will undergo input over-voltage shutdown. 2. Derate output power to 50% of rated power at Tcase = 135 C. 3. High or low state of input voltage must persist for about 200s to be acted on by the lockout or shutdown circuitry. 4. Current limit inception is defined as the point where the output voltage has dropped to 90% of its nominal value. 5. Parameter not tested but guaranteed to the limit specified. 6. Load current transition time 10s. 7. Settling time measured from start of transient to the point where the output voltage has returned to 50mV of its final value. 8. Line voltage transition time 100s. 9. Input voltage rise time 250s. 10. Operating the converter at a synchronization frequency above the free running frequency will cause the converter's efficiency to be slightly reduced and it may also cause a slight reduction in the maximum output current/power available. For more information consult the factory. 11. After a disable or fault event, module is inhibited from restarting for 300ms. See Shut Down section on Page 9. 12. SHARE pin outputs a power failure warning pulse during a fault condition. See Current Share section on Page 11. 13. Only the ES and HB grade products are tested at three temperatures. The B and C grade products are tested at one temperature. Please refer to the ESS table on Page 13 for details. 14. These derating curves apply for the ES- and HB- grade products. The C- grade product has a maximum case temperature of 100 C and a maximum junction temperature rise of 20 C above TCASE. The B- grade product has a maximum case temperature of 85 C and a maximum junction temperature rise of 20 C at full load. Product # MQFL-28-2R5S Phone 1-888-567-9596 www.synqor.com Doc.# 005-2MQ250S Rev. B 03/19/09 Page 4 MQFL-28-2R5S Output: 2.5 V Current: 40 A 100 100 95 95 90 90 Efficiency (%) Efficiency (%) Technical Specification 85 80 75 70 80 75 70 16 Vin 28 Vin 65 85 16 Vin 28 Vin 40 Vin 65 40 Vin 60 60 0 5 10 15 20 25 30 35 -55C 40 25C Load Current (A) 125C Case Temperature (C) Figure 1: Efficiency at nominal output voltage vs. load current for minimum, nominal, and maximum input voltage at Tcase=25C. Figure 2: Efficiency at nominal output voltage and 60% rated power vs. case temperature for input voltage of 16V, 28V, and 40V. 16 20 18 14 Power Dissipation (W) Power Dissipation (W) 16 14 12 10 8 6 16 Vin 4 12 10 8 6 4 16 Vin 28 Vin 2 28 Vin 2 40 Vin 40 Vin 0 0 0 5 10 15 20 25 30 35 40 -55C 25C Load Current (A) 125C Case Temperature (C) Figure 3: Power dissipation at nominal output voltage vs. load current for minimum, nominal, and maximum input voltage at Tcase=25C. 50 Figure 4: Power dissipation at nominal output voltage and 60% rated power vs. case temperature for input voltage of 16V, 28V, and 40V. 3.0 125 45 40 2.5 100 75 25 20 Output Voltage (V) 30 Pout (W) Iout (A) 35 50 15 Tjmax = 105C Tjmax = 125C Tjmax = 145C 10 5 65 28 Vin 85 105 125 135 0.0 145 0 Figure 5: Output Current / Output Power derating curve as a function of Tcase and the Maximum desired power MOSFET junction temperature at Vin = 28V (see Note 14). Phone 1-888-567-9596 5 10 15 20 25 30 35 40 45 50 Load Current (A) Case Temperature (C) Product # MQFL-28-2R5S 1.0 0.5 0 45 1.5 25 0 25 2.0 Figure 6: Output voltage vs. load current showing typical current limit curves. www.synqor.com Doc.# 005-2MQ250S Rev. B 03/19/09 Page 5 MQFL-28-2R5S Output: 2.5 V Current: 40 A Technical Specification Figure 7: Turn-on transient at full resistive load and zero output capacitance initiated by ENA1. Input voltage pre-applied. Ch 1: Vout (500mV/ div). Ch 2: ENA1 (5V/div). Figure 8: Turn-on transient at full resistive load and 10mF output capacitance initiated by ENA1. Input voltage pre-applied. Ch 1: Vout (500mV/ div). Ch 2: ENA1 (5V/div). Figure 9: Turn-on transient at full resistive load and zero output capacitance initiated by ENA2. Input voltage pre-applied. Ch 1: Vout (500mV/ div). Ch 2: ENA2 (5V/div). Figure 10: Turn-on transient at full resistive load and zero output capacitance initiated by Vin. ENA1 and ENA2 both previously high. Ch 1: Vout (500mV/div). Ch 2: Vin (10V/div). Figure 11: Output voltage response to step-change in load current 50%100%-50% of Iout (max). Load cap: 1F ceramic cap and 10F, 100m ESR tantalum cap. Ch 1: Vout (200mV/div). Ch 2: Iout (20A/div). Figure 12: Output voltage response to step-change in load current 0%-50%-0% of Iout (max). Load cap: 1F ceramic cap and 10F, 100 m ESR tantalum cap. Ch 1: Vout (200mV/div). Ch 2: Iout (20A/div). Product # MQFL-28-2R5S Phone 1-888-567-9596 www.synqor.com Doc.# 005-2MQ250S Rev. B 03/19/09 Page 6 MQFL-28-2R5S Output: 2.5 V Current: 40 A Technical Specification See Fig. 15 MQME Filter iC See Fig. 16 MQFL Converter VSOURCE VOUT 1 F 10 F, ceramic 100mW ESR capacitor capacitor Figure 13: Output voltage response to step-change in input voltage (16V 50V - 16V). Load cap: 10F, 100m ESR tantalum cap and 1F ceramic cap. Ch 1: Vout (200mV/div). Ch 2: Vin (20V/div). Figure 14: Test set-up diagram showing measurement points for Input Terminal Ripple Current (Figure 15) and Output Voltage Ripple (Figure 16). Figure 15: Input terminal current ripple, ic, at full rated output current and nominal input voltage with SynQor MQ filter module (50mA/div). Bandwidth: 20MHz. See Figure 14. Figure 16: Output voltage ripple, Vout, at nominal input voltage and rated load current (20mV/div). Load capacitance: 1F ceramic capacitor and 10F tantalum capacitor. Bandwidth: 10MHz. See Figure 14. Figure 17: Rise of output voltage after the removal of a short circuit across the output terminals. Ch 1: Vout (500mV/div). Ch 2: Iout (20A/div). Figure 18: SYNC OUT vs. time, driving SYNC IN of a second SynQor MQFL converter. Ch1: SYNC OUT: (1V/div). Product # MQFL-28-2R5S Phone 1-888-567-9596 www.synqor.com Doc.# 005-2MQ250S Rev. B 03/19/09 Page 7 MQFL-28-2R5S Output: 2.5 V Current: 40 A Technical Specification 0.1 0 Forward Transmission (dB) Output Impedance (ohms) -10 0.01 0.001 16Vin 28Vin -20 -30 -40 -50 -60 -70 16Vin 28Vin -80 40Vin -90 0.0001 40Vin -100 10 100 1,000 10,000 100,000 10 100 Hz 1,000 10,000 100,000 Hz Figure 19: Magnitude of incremental output impedance (Zout = vout/iout) for minimum, nominal, and maximum input voltage at full rated power. Figure 20: Magnitude of incremental forward transmission (FT = vout/vin) for minimum, nominal, and maximum input voltage at full rated power. 10 100 Input Impedance (ohms) Reverse Transmission (dB) 0 -10 -20 -30 16Vin 28Vin -40 10 1 16Vin 28Vin 0.1 40Vin 40Vin -50 0.01 10 100 1,000 10,000 100,000 10 Hz 100 1,000 10,000 100,000 Hz Figure 21: Magnitude of incremental reverse transmission (RT = iin/iout) for minimum, nominal, and maximum input voltage at full rated power. Figure 22: Magnitude of incremental input impedance (Zin = vin/iin) for minimum, nominal, and maximum input voltage at full rated power. Figure 23: High frequency conducted emissions of standalone MQFL-2805S, 5Vout module at 120W output, as measured with Method CE102. Limit line shown is the `Basic Curve' for all applications with a 28V source. Figure 24: High frequency conducted emissions of MQFL-28-05S, 5Vout module at 120W output with MQFL-28-P filter, as measured with Method CE102. Limit line shown is the `Basic Curve' for all applications with a 28V source. Product # MQFL-28-2R5S Phone 1-888-567-9596 www.synqor.com Doc.# 005-2MQ250S Rev. B 03/19/09 Page 8 MQFL-28-2R5S Output: 2.5 V Current: 40 A Technical Specification BASIC OPERATION AND FEATURES The MQFL DC/DC converter uses a two-stage power conversion topology. The first, or regulation, stage is a buck-converter that keeps the output voltage constant over variations in line, load, and temperature. The second, or isolation, stage uses transformers to provide the functions of input/output isolation and voltage transformation to achieve the output voltage required. Both the regulation and the isolation stages switch at a fixed frequency for predictable EMI performance. The isolation stage switches at one half the frequency of the regulation stage, but due to the push-pull nature of this stage it creates a ripple at double its switching frequency. As a result, both the input and the output of the converter have a fundamental ripple frequency of about 550 kHz in the free-running mode. Rectification of the isolation stage's output is accomplished with synchronous rectifiers. These devices, which are MOSFETs with a very low resistance, dissipate far less energy than would Schottky diodes. This is the primary reason why the MQFL converters have such high efficiency, particularly at low output voltages. CONTROL FEATURES ENABLE: The MQFL converter has two enable pins. Both must have a logic high level for the converter to be enabled. A logic low on either pin will inhibit the converter. The ENA1 pin (pin 4) is referenced with respect to the converter's input return (pin 2). The ENA2 pin (pin 12) is referenced with respect to the converter's output return (pin 8). This permits the converter to be inhibited from either the input or the output side. Regardless of which pin is used to inhibit the converter, the regulation and the isolation stages are turned off. However, when the converter is inhibited through the ENA1 pin, the bias supply is also turned off, whereas this supply remains on when the converter is inhibited through the ENA2 pin. A higher input standby current therefore results in the latter case. Both enable pins are internally pulled high so that an open connection on both pins will enable the converter. Figure A shows the equivalent circuit looking into either enable pins. It is TTL compatible. Besides improving efficiency, the synchronous rectifiers permit operation down to zero load current. There is no longer a need for a minimum load, as is typical for converters that use diodes for rectification. The synchronous rectifiers actually permit a negative load current to flow back into the converter's output terminals if the load is a source of short or long term energy. The MQFL converters employ a "back-drive current limit" to keep this negative output terminal current small. There is a control circuit on both the input and output sides of the MQFL converter that determines the conduction state of the power switches. These circuits communicate with each other across the isolation barrier through a magnetically coupled device. No optoisolators are used. A separate bias supply provides power to both the input and output control circuits. Among other things, this bias supply permits the converter to operate indefinitely into a short circuit and to avoid a hiccup mode, even under a tough start-up condition. An input under-voltage lockout feature with hysteresis is provided, as well as an input over-voltage shutdown. There is also an output current limit that is nearly constant as the load impedance decreases to a short circuit (i.e., there is not foldback or fold-forward characteristic to the output current under this condition). When a load fault is removed, the output voltage rises exponentially to its nominal value without an overshoot. The MQFL converter's control circuit does not implement an output over-voltage limit or an over-temperature shutdown. The following sections describe the use and operation of additional control features provided by the MQFL converter. Product # MQFL-28-2R5S Phone 1-888-567-9596 Figure A: Equivalent circuit looking into either the ENA1 or ENA2 pins with respect to its corresponding return pin. SHUT DOWN: The MQFL converter will shut down in response to only four conditions: ENA1 input low, ENA2 input low, VIN input below under-voltage lockout threshold, or VIN input above over-voltage shutdown threshold. Following a shutdown event, there is a startup inhibit delay which will prevent the converter from restarting for approximately 300ms. After the 300ms delay elapses, if the enable inputs are high and the input voltage is within the operating range, the converter will restart. If the VIN input is brought down to nearly 0V and back into the operating range, there is no startup inhibit, and the output voltage will rise according to the "Turn-On Delay, Rising Vin" specification. www.synqor.com Doc.# 005-2MQ250S Rev. B 03/19/09 Page 9 MQFL-28-2R5S Output: 2.5 V Current: 40 A Technical Specification REMOTE SENSE: The purpose of the remote sense pins is to correct for the voltage drop along the conductors that connect the converter's output to the load. To achieve this goal, a separate conductor should be used to connect the +SENSE pin (pin 10) directly to the positive terminal of the load, as shown in the connection diagram on Page 2. Similarly, the -SENSE pin (pin 9) should be connected through a separate conductor to the return terminal of the load. This frequency is either the free-running frequency if there is no synchronization signal at the SYNC IN pin, or the synchronization frequency if there is. NOTE: Even if remote sensing of the load voltage is not desired, the +SENSE and the -SENSE pins must be connected to +Vout (pin 7) and OUTPUT RETURN (pin 8), respectively, to get proper regulation of the converter's output. If they are left open, the converter will have an output voltage that is approximately 200mV higher than its specified value. If only the +SENSE pin is left open, the output voltage will be approximately 25mV too high. NOTE: An MQFL converter that has its SYNC IN pin driven by the SYNC OUT pin of a second MQFL converter will have its start of its switching cycle delayed approximately 180 degrees relative to that of the second converter. The SYNC OUT signal is available only when the DC input voltage is above approximately 12V and when the converter is not inhibited through the ENA1 pin. An inhibit through the ENA2 pin will not turn the SYNC OUT signal off. Figure B shows the equivalent circuit looking into the SYNC IN pin. Figure C shows the equivalent circuit looking into the SYNC OUT pin. Inside the converter, +SENSE is connected to +Vout with a resistor value from 100 to 274, depending on output voltage, and -SENSE is connected to OUTPUT RETURN with a 10 resistor. It is also important to note that when remote sense is used, the voltage across the converter's output terminals (pins 7 and 8) will be higher than the converter's nominal output voltage due to resistive drops along the connecting wires. This higher voltage at the terminals produces a greater voltage stress on the converter's internal components and may cause the converter to fail to deliver the desired output voltage at the low end of the input voltage range at the higher end of the load current and temperature range. Please consult the factory for details. Figure B: Equivalent circuit looking into the SYNC IN pin with respect to the IN RTN (input return) pin. SYNCHRONIZATION: The MQFL converter's switching frequency can be synchronized to an external frequency source that is in the 500 kHz to 700 kHz range. A pulse train at the desired frequency should be applied to the SYNC IN pin (pin 6) with respect to the INPUT RETURN (pin 2). This pulse train should have a duty cycle in the 20% to 80% range. Its low value should be below 0.8V to be guaranteed to be interpreted as a logic low, and its high value should be above 2.0V to be guaranteed to be interpreted as a logic high. The transition time between the two states should be less than 300ns. If the MQFL converter is not to be synchronized, the SYNC IN pin should be left open circuit. The converter will then operate in its free-running mode at a frequency of approximately 550 kHz. If, due to a fault, the SYNC IN pin is held in either a logic low or logic high state continuously, the MQFL converter will revert to its free-running frequency. The MQFL converter also has a SYNC OUT pin (pin 5). This output can be used to drive the SYNC IN pins of as many as ten (10) other MQFL converters. The pulse train coming out of SYNC OUT has a duty cycle of 50% and a frequency that matches the switching frequency of the converter with which it is associated. Product # MQFL-28-2R5S Phone 1-888-567-9596 Figure C: Equivalent circuit looking into SYNC OUT pin with respect to the IN RTN (input return) pin. CURRENT SHARE: When several MQFL converters are placed in parallel to achieve either a higher total load power or N+1 redundancy, their SHARE pins (pin 11) should be connected together. The voltage on this common SHARE node represents the average current delivered by all of the paralleled converters. Each converter monitors this average value and adjusts itself so that its output current closely matches that of the average. www.synqor.com Doc.# 005-2MQ250S Rev. B 03/19/09 Page 10 MQFL-28-2R5S Output: 2.5 V Current: 40 A Technical Specification Since the SHARE pin is monitored with respect to the OUTPUT RETURN (pin 8) by each converter, it is important to connect all of the converters' OUTPUT RETURN pins together through a low DC and AC impedance. When this is done correctly, the converters will deliver their appropriate fraction of the total load current to within +/- 10% at full rated load. Whether or not converters are paralleled, the voltage at the SHARE pin could be used to monitor the approximate average current delivered by the converter(s). A nominal voltage of 1.0V represents zero current and a nominal voltage of 2.2V represents the maximum rated current, with a linear relationship in between. The internal source resistance of a converter's SHARE pin signal is 2.5 kW. During an input voltage fault or primary disable event, the SHARE pin outputs a power failure warning pulse. The SHARE pin will go to 3V for approximately 14ms as the output voltage falls. NOTE: Converters operating from separate input filters with reverse polarity protection (such as the MQME-28-T filter) with their outputs connected in parallel may exhibit hiccup operation at light loads. Consult factory for details. OUTPUT VOLTAGE TRIM: If desired, it is possible to increase the MQFL converter's output voltage above its nominal value. To do this, use the +SENSE pin (pin 10) for this trim function instead of for its normal remote sense function, as shown in Figure D. In this case, a resistor connects the +SENSE pin to the -SENSE pin (which should still be connected to the output return, either remotely or locally). The value of the trim resistor should be chosen according to the following equation or from Figure E: Rtrim = 407.5 Vout - Vnom - 0.025 where: Vnom = the converter's nominal output voltage, Vout = the desired output voltage (greater than Vnom), and Rtrim is in Ohms. 1 2 3 4 28Vdc + - 5 open means on 6 Figure E: Output Voltage Trim Graph As the output voltage is trimmed up, it produces a greater voltage stress on the converter's internal components and may cause the converter to fail to deliver the desired output voltage at the low end of the input voltage range at the higher end of the load current and temperature range. Please consult the factory for details. Factory trimmed converters are available by request. INPUT UNDER-VOLTAGE LOCKOUT: The MQFL converter has an under-voltage lockout feature that ensures the converter will be off if the input voltage is too low. The threshold of input voltage at which the converter will turn on is higher that the threshold at which it will turn off. In addition, the MQFL converter will not respond to a state of the input voltage unless it has remained in that state for more than about 200s. This hysteresis and the delay ensure proper operation when the source impedance is high or in a noisy environment. INPUT OVER-VOLTAGE SHUTDOWN: The MQFL converter also has an over-voltage feature that ensures the converter will be off if the input voltage is too high. It also has a hysteresis and time delay to ensure proper operation. +VIN ENA 2 IN RTN SHARE CASE + SNS ENA 1 - SNS SYNC OUT OUT RTN +VOUT SYNC IN 12 11 10 9 Rtrim - 8 7 Load + Figure D: Typical connection for output voltage trimming. Product # MQFL-28-2R5S Phone 1-888-567-9596 www.synqor.com Doc.# 005-2MQ250S Rev. B 03/19/09 Page 11 MQFL-28-2R5S Output: 2.5 V Current: 40 A Technical Specification BACK-DRIVE CURRENT LIMIT: Converters that use MOSFETs as synchronous rectifiers are capable of drawing a negative current from the load if the load is a source of short- or long-term energy. This negative current is referred to as a "back-drive current". Conditions where back-drive current might occur include paralleled converters that do not employ current sharing, or where the current share feature does not adequately ensure sharing during the startup or shutdown transitions. It can also occur when converters having different output voltages are connected together through either explicit or parasitic diodes that, while normally off, become conductive during startup or shutdown. Finally, some loads, such as motors, can return energy to their power rail. Even a load capacitor is a source of back-drive energy for some period of time during a shutdown transient. To avoid any problems that might arise due to back-drive current, the MQFL converters limit the negative current that the converter can draw from its output terminals. The threshold for this backdrive current limit is placed sufficiently below zero so that the converter may operate properly down to zero load, but its absolute value (see the Electrical Characteristics page) is small compared to the converter's rated output current. THERMAL CONSIDERATIONS: Figure 5 shows the suggested Power Derating Curves for this converter as a function of the case temperature and the maximum desired power MOSFET junction temperature. All other components within the converter are cooler than its hottest MOSFET, which at full power is no more than 20C higher than the case temperature directly below this MOSFET. Product # MQFL-28-2R5S Phone 1-888-567-9596 The Mil-HDBK-1547A component derating guideline calls for a maximum component temperature of 105C. Figure 5 therefore has one power derating curve that ensures this limit is maintained. It has been SynQor's extensive experience that reliable long-term converter operation can be achieved with a maximum component temperature of 125C. In extreme cases, a maximum temperature of 145C is permissible, but not recommended for long-term operation where high reliability is required. Derating curves for these higher temperature limits are also included in Figure 5. The maximum case temperature at which the converter should be operated is 135C. When the converter is mounted on a metal plate, the plate will help to make the converter's case bottom a uniform temperature. How well it does so depends on the thickness of the plate and on the thermal conductance of the interface layer (e.g. thermal grease, thermal pad, etc.) between the case and the plate. Unless this is done very well, it is important not to mistake the plate's temperature for the maximum case temperature. It is easy for them to be as much as 5-10C different at full power and at high temperatures. It is suggested that a thermocouple be attached directly to the converter's case through a small hole in the plate when investigating how hot the converter is getting. Care must also be made to ensure that there is not a large thermal resistance between the thermocouple and the case due to whatever adhesive might be used to hold the thermocouple in place. INPUT SYSTEM INSTABILITY: This condition can occur because any DC/DC converter appears incrementally as a negative resistance load. A detailed application note titled "Input System Instability" is available on the SynQor website which provides an understanding of why this instability arises, and shows the preferred solution for correcting it. www.synqor.com Doc.# 005-2MQ250S Rev. B 03/19/09 Page 12 MQFL-28-2R5S Output: 2.5 V Current: 40 A Technical Specification CONSTRUCTION AND ENVIRONMENTAL STRESS SCREENING OPTIONS Screening Consistent with MIL-STD-883F B-Grade (-40 C to +85 C) C-Grade (-40 C to +100 C) ES-Grade (-55 C to +125 C) (Element Evaluation) HB-Grade (-55 C to +125 C) (Element Evaluation) Internal Visual * Yes Yes Yes Yes Temperature Cycle Method 1010 No No Condition B (-55 C to +125 C) Condition C (-65 C to +150 C) Constant Acceleration Method 2001 (Y1 Direction) No No 500g Condition A (5000g) Burn-in Method 1015 Load Cycled * 10s period * 2s @ 100% Load * 8s @ 0% Load 12 Hrs @ +100 C 24 Hrs @ +125 C 96 Hrs @ +125 C 160 Hrs @ +125 C Final Electrical Test Method 5005 (Group A) +25 C +25 C -45, +25, +100 C -55, +25, +125 C Anodized Package Full QorSeal Full QorSeal Full QorSeal * * Yes Yes Ruggedized QorSeal QorSeal QorSeal Mechanical Seal, Thermal, and Coating Process External Visual Construction Process 2009 * Per IPC-A-610 (Rev. D) Class 3 MilQor converters and filters are offered in four variations of construction technique and environmental stress screening options. The three highest grades, C, ES, and HB, all use SynQor's proprietary QorSealTM Hi-Rel assembly process that includes a Parylene-C coating of the circuit, a high performance thermal compound filler, and a nickel barrier gold plated aluminum case. The B-grade version uses a ruggedized assembly process that includes a medium performance thermal compound filler and a black anodized aluminum case. Each successively higher grade has more stringent mechanical and electrical testing, as well as a longer burn-in cycle. The ES- and HB-Grades are also constructed of components that have been procured through an element evaluation process that pre-qualifies each new batch of devices. Note: Since the surface of the black anodized case is not guaranteed to be electrically conductive, a star washer or similar device should be used to cut through the surface oxide if electrical connection to the case is desired. Product # MQFL-28-2R5S Phone 1-888-567-9596 www.synqor.com Doc.# 005-2MQ250S Rev. B 03/19/09 Page 13 MQFL-28-2R5S Output: 2.5 V Current: 40 A Technical Specification 0.093 [2.36] 1 2 3 4 5 6 +VIN ENA 2 IN RTN CASE ENA 1 SHARE MQFL-28-2R5S-X-HB DC/DC CONVERTER 28Vin 2.5Vout @ 40A -SNS MADE IN USA SYNC OUT SYNC IN +SNS S/N 0000000 D/C 3205-301 CAGE 1WX10 OUT RTN +VOUT 12 11 10 9 8 7 0.250 [6.35] 1.50 [38.10] 1.260 [32.00] 0.200 [5.08] TYP. NON-CUM. 0.040 [1.02] PIN 2.50 [63.50] 2.76 [70.10] 3.00 [76.20] 0.050 [1.27] 0.128 [3.25] 0.220 [5.59] 2.96 [75.2] 0.228 [5.79] 0.390 [9.91] Case X 0.093 [2.36] 1 2 3 4 5 6 +VIN ENA 2 IN RTN CASE ENA 1 SHARE MQFL-28-2R5S-U-HB SYNC OUT SYNC IN +SNS DC/DC CONVERTER 28Vin 2.5Vout @ 40A -SNS MADE IN USA S/N 0000000 D/C 3205-301 CAGE 1WX10 OUT RTN +VOUT 2.50 [63.50] 2.76 [70.10] 3.00 [76.20] 12 11 10 9 8 7 0.250 [6.35] 0.200 [5.08] TYP. NON-CUM. 1.50 [38.10] 1.260 [32.00] 0.040 [1.02] PIN 0.42 [10.7] 0.128 [3.25] 0.050 [1.27] 0.220 [5.59] 2.80 [71.1] Case U 0.390 [9.91] NOTES PIN DESIGNATIONS 1) Pins 0.040" (1.02mm) diameter 2) Pins Material: Copper Finish: Gold over Nickel plate 1 Positive input 7 Positive output 3) All dimensions in inches (mm) Tolerances: x.xx +/-0.02 in. (x.x +/-0.5mm) x.xxx +/-0.010 in. (x.xx +/-0.25mm) 2 Input return 8 Output return Weight: 2.8 oz (78.5 g) typical 3 CASE 9 - Sense 4) 5) Workmanship: Meets or exceeds IPC-A-610C Class III 4 Enable 1 10 + Sense 6) Print Labeling on Top Surface per Product Label Format Drawing 5 Sync output 11 Share 6 Sync input 12 Enable 2 Product # MQFL-28-2R5S Phone 1-888-567-9596 Pin Function www.synqor.com Doc.# 005-2MQ250S Rev. B Pin Function 03/19/09 Page 14 MQFL-28-2R5S Output: 2.5 V Current: 40 A Technical Specification 1 2 3 4 5 6 0.300 [7.62] 0.140 [3.56] 1.15 [29.21] 0.250 [6.35] TYP +VIN ENA 2 IN RTN SHARE MQFL-28-2R5S-Y-HB CASE ENA 1 -SNS SYNC OUT SYNC IN +SNS DC/DC CONVERTER 28Vin 2.5Vout @ 40A MADE IN USA S/N 0000000 D/C 3205-301 CAGE 1WX10 OUT RTN +VOUT 1.750 [44.45] 0.250 [6.35] 12 2.00 11 [50.80] 10 1.50 9 [38.10] 8 1.750 7 [44.45] 0.200 [5.08] TYP. NON-CUM. 0.040 [1.02] PIN 0.050 [1.27] 0.375 [9.52] 2.50 [63.50] 0.220 [5.59] 2.96 [75.2] 0.228 [5.79] Case Y 0.390 [9.91] Case Z (variant of Y) 0.250 [6.35] Case W (variant of Y) 0.250 [6.35] 0.200 [5.08] TYP. NON-CUM. 0.200 [5.08] TYP. NON-CUM. 0.040 [1.02] PIN 0.040 [1.02] PIN 0.220 [5.59] 0.050 [1.27] 0.420 [10.7] 0.050 [1.27] 0.220 [5.59] 0.36 [9.2] 2.80 [71.1] 0.525 [13.33] 0.390 [9.91] 0.390 [9.91] 0.525 [13.33] 2.80 [71.1] PIN DESIGNATIONS NOTES 1) 2) 3) 4) 5) 6) Pins 0.040" (1.02mm) diameter Pins Material: Copper Finish: Gold over Nickel plate All dimensions in inches (mm) Tolerances: x.xx +/-0.02 in. (x.x +/-0.5mm) x.xxx +/-0.010 in. (x.xx +/-0.25mm) Weight: 2.8 oz (78.5 g) typical Workmanship: Meets or exceeds IPC-A-610C Class III Print Labeling on Top Surface per Product Label Format Drawing Product # MQFL-28-2R5S Phone 1-888-567-9596 www.synqor.com Pin Function 1 2 3 4 5 6 Positive input Input return CASE Enable 1 Sync output Sync input Doc.# 005-2MQ250S Rev. B Pin Function 7 8 9 10 11 12 Positive output Output return - Sense + Sense Share Enable 2 03/19/09 Page 15 MQFL-28-2R5S Output: 2.5 V Current: 40 A Technical Specification MilQor MQFL FAMILY MATRIX The tables below show the array of MQFL converters available. When ordering SynQor converters, please ensure that you use the complete part number according to the table in the last page. Contact the factory for other requirements. Single Output 1.5V (1R5S) 1.8V (1R8S) 2.5V (2R5S) 3.3V (3R3S) 5V (05S) 6V (06S) 7.5V (7R5S) 9V (09S) 12V (12S) 15V (15S) 28V (28S) 40A 40A 40A 30A 24A 20A 16A 13A 10A 8A 4A 40A 40A 40A 30A 24A 20A 16A 13A 10A 8A 4A 40A 40A 40A 30A 20A 17A 13A 11A 8A 6.5A 3.3A 40A 40A 40A 30A 20A 17A 13A 11A 8A 6.5A 3.3A 40A 40A 40A 30A 24A 20A 16A 13A 10A 8A 4A 40A 40A 40A 30A 20A 17A 13A 11A 8A 6.5A 3.3A 40A 40A 30A 22A 15A 12A 10A 8A 6A 5A 2.7A MQFL-28 16-40Vin Cont. 16-50Vin 1s Trans.* Absolute Max Vin = 60V MQFL-28E 16-70Vin Cont. 16-80Vin 1s Trans.* Absolute Max Vin =100V MQFL-28V 16-40Vin Cont. 5.5-50Vin 1s Trans.* Absolute Max Vin = 60V MQFL-28VE 16-70Vin Cont. 5.5-80Vin 1s Trans.* Absolute Max Vin = 100V MQFL-270 155-400Vin Cont. 155-475Vin 0.1s Trans.* Absolute Max Vin = 550V MQFL-270E 130-475Vin Cont. 130-520Vin 0.1s Trans.* Absolute Max Vin = 600V MQFL-270L 65-350Vin Cont. 65-475Vin 0.1s Trans.* Absolute Max Vin = 550V Dual Output 5V (05D) 12V (12D) 15V (15D) 24A Total 10A Total 8A Total 16-40Vin Cont. 16-50Vin 1s Trans.* Absolute Max Vin = 60V 24A Total 10A Total 8A Total 16-70Vin Cont. 16-80Vin 1s Trans.* Absolute Max Vin =100V 20A Total 8A Total 6.5A Total 16-40Vin Cont. 5.5-50Vin 1s Trans.* Absolute Max Vin = 60V 20A Total 8A Total 6.5A Total 16-70Vin Cont. 5.5-80Vin 1s Trans.* Absolute Max Vin = 100V MQFL-28 16-40Vin Cont. 16-50Vin 1s Trans.* Absolute Max Vin = 60V 10A Total 8A Total 155-400Vin Cont. 155-475Vin 0.1s Trans.* Absolute Max Vin = 550V 22A/ 1A 22A/ 0.8A 15A/ 1A 15A/ 0.8A 2.5A/ 0.8A 22A/ 1A 22A/ 0.8A 15A/ 1A 15A/ 0.8A 2.5A/ 0.8A 22A/ 1A 22A/ 0.8A 15A/ 1A 15A/ 0.8A 2.5A/ 0.8A 22A/ 1A 22A/ 0.8A 15A/ 1A 15A/ 0.8A 2.5A/ 0.8A 22A/ 1A 22A/ 0.8A 15A/ 1A 15A/ 0.8A 2.5A/ 0.8A 22A/ 1A 22A/ 0.8A 15A/ 1A 15A/ 0.8A 2.5A/ 0.8A 22A/ 1A 22A/ 0.8A 15A/ 1A 15A/ 0.8A 2.5A/ 0.8A MQFL-270E 20A Total 8A Total 6.5A Total 130-475Vin Cont. 130-520Vin 0.1s Trans.* Absolute Max Vin = 600V 15A Total 6A Total 5A Total 65-350Vin Cont. 65-475Vin 0.1s Trans.* Absolute Max Vin = 550V MQFL-270L 65-350Vin Cont. 65-475Vin 0.1s Trans.* Absolute Max Vin = 550V 30V/15V (3015T) MQFL-270 24A Total MQFL-270E 130-475Vin Cont. 130-520Vin 0.1s Trans.* Absolute Max Vin = 600V 5V/15V (0515T) MQFL-28VE MQFL-270 155-400Vin Cont. 155-475Vin 0.1s Trans.* Absolute Max Vin = 550V 5V/12V (0512T) MQFL-28V MQFL-28VE 16-70Vin Cont. 5.5-80Vin 1s Trans.* Absolute Max Vin = 100V 3.3V/15V (3R315T) MQFL-28E MQFL-28V 16-40Vin Cont. 5.5-50Vin 1s Trans.* Absolute Max Vin = 60V 3.3V/12V (3R312T) MQFL-28 MQFL-28E 16-70Vin Cont. 16-80Vin 1s Trans.* Absolute Max Vin =100V Triple Output MQFL-270L (75Wmax Total Output Power) *Converters may be operated continuously at the highest transient input voltage, but some component electrical and thermal stresses would be beyond MIL-HDBK-1547A guidelines. Product # MQFL-28-2R5S Phone 1-888-567-9596 www.synqor.com 80% of total output current available on any one output. Doc.# 005-2MQ250S Rev. B 03/19/09 Page 16 MQFL-28-2R5S Output: 2.5 V Current: 40 A Technical Specification PART NUMBERING SYSTEM The part numbering system for SynQor's MilQor DC-DC converters follows the format shown in the table below. Model Name Input Voltage Range MQFL 28 28E 28V 28VE 270 270E 270L Output Voltage(s) Single Output Dual Output Triple Output 1R5S 1R8S 2R5S 3R3S 05S 06S 7R5S 09S 12S 15S 28S 05D 12D 15D 3R312T 3R315T 0512T 0515T 3015T Example: Package Outline/ Pin Configuration Screening Grade U X Y W Z B C ES HB MQFL - 28VE - 2R5S - Y - ES APPLICATION NOTES A variety of application notes and technical white papers can be downloaded in pdf format from the SynQor website. PATENTS SynQor holds the following patents, one or more of which might apply to this product: 5,999,417 6,594,159 6,927,987 7,119,524 6,222,742 6,731,520 7,050,309 7,269,034 6,545,890 6,894,468 7,072,190 7,272,021 6,577,109 6,896,526 7,085,146 7,272,023 Contact SynQor for further information: Phone: Toll Free: Fax: E-mail: Web: Address: Product # MQFL-28-2R5S 978-849-0600 888-567-9596 978-849-0602 power@synqor.com www.synqor.com 155 Swanson Road Boxborough, MA 01719 USA Phone 1-888-567-9596 Warranty SynQor offers a two (2) year limited warranty. Complete warranty information is listed on our website or is available upon request from SynQor. Information furnished by SynQor is believed to be accurate and reliable. However, no responsibility is assumed by SynQor for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SynQor. www.synqor.com Doc.# 005-2MQ250S Rev. B 03/19/09 Page 17