Single-chip Type with Built-in FET Switching Regulator Series Simple Step-down Switching Regulators with Built-in Power MOSFET BD9701FP/CP-V5/T/T-V5, BD9703FP/CP-V5/T/T-V5,BD9702CP-V5/T/T-V5 No.09027EBT01 Description The BD9701/BD9703/BD9702 are single-channel step-down switching regulator capable of PWM operation. The Pch MOS FET is built in for high efficiency in small load area.Lower electricity consumption of operating current 4mA (Typ) and stand-by current 0uA(Typ) is realized by adopting Bi-CMOS process. Features 1) Maximum switching current: 1.5A(BD9701/BD9703), 3A(BD9702) 2) Built-in Pch FET ensures high efficiency 3) Output voltage adjustable via external resistors 4) High switching frequency: 100kHz (BD9701), 300kHz(BD9703), 110kHz(BD9702) 5) Overcurrent and thermal shutdown protection circuits built in 6) ON/OFF control via STBY pin 7) Small surface mount TO252-5 package (only BD9701FP, BD9703FP) Applications TVs, printers, DVD players, projectors, gaming devices, PCs, car audio/navigation systems, ETCs, communication equipment, AV products, office equipment, industrial devices, and more. Line Up BD9701FP/CP-V5/T/T-V5 BD9703FP/CP-V5/T/T-V5 BD9702CP-V5/T/T-V5 1.5A 3.0A Output Current Input Voltage Switching Frequency 100kHz (fixed) 8 or Vo+3 36V 300kHz (fixed) External Synchronization x Stand-by Function Operating Temperature Package 110kHz (fixed) -40 +85 TO252-5/TO220CP-V5/TO220FP-5/TO220FP-5 (V5) TO220CP-V5/TO220FP-5/TO220FP-5 (V5) www.rohm.com (c) 2009 ROHM Co., Ltd. All rights reserved. 1/16 2009.04- Rev.B BD9701FP/CP-V5/T/T-V5,BD9703FP/CP-V5/T/T-V5,BD9702CP-V5/T/T-V5 Technical Note Absolute Maximum Ratings (Ta25) Parameter Symbol Ratings Unit Supply Voltage (VCC-GND) VCC 36 V STBY-GND VSTBY 36 V OUT-GND VO 36 V INV-GND VINV 10 V BD9701/BD9703 Maximum Switching Current BD9702 TO252 Power Dissipation 1.5 Iout 0.8 (*1) Pd TO220 A 3 W 2(*2) Operating Temperature Topr -40+85 Storage Temperature Tstg -55+150 *1 Without external heat sink, the power dissipation reduces by 6.4mW/ over 25. *2 Without external heat sink, the power dissipation reduces by 16.0mW/ over 25. Reduced by 160mW/, when mounted on Infinity size heatsink. Operating Conditions(Ta=-40+85) Parameter Limit Symbol Input Voltage Output Voltage Unit MIN TYP MAX VCC 8.0 or Vo+3(*3) - 35.0 V Vo 1.0 - 32 V *3The minimum value of an input voltage is the higher either 8.0V or Vo+3 Electrical Characteristics BD9701FP/CP-V5/T/T-V5 (Unless otherwise noted, Ta=25,VCC=12V,Vo=5V,STBY=3V) Parameter Symbol Limit Unit Conditions MIN TYP MAX Ron - 1.0 1.5 design guarantee - 86 - % Io0.5A design guarantee fosc 80 100 120 kHz Load Regulation VOLOAD - 10 40 mV VCC=20V,Io=0.51.5A Line Regulation VOLINE - 40 100 mV VCC=1030V,Io=1.0A Over Current Protection Limit Iocp 1.6 - - A INV Pin Threshold Voltage VINV 0.98 1.00 1.02 V INV Pin Threshold Voltage Thermal Variation VINV - 0.5 - % Tj=085 design guarantee IINV - 1 - A VINV=1.0V ON VSTBYON 2.0 - 36 V OFF VSTBYOFF -0.3 - 0.3 V Istby 5 25 50 A Circuit Current Icc - 4 12 mA Stand-by Current Ist - 0 5 A Output ON Resistance Efficiency Switching Frequency INV Pin Input Current STBY Pin Threshold Voltage STBY Pin Input Current STBY=3V STBY0V This product is not designed to be resistant to radiation. www.rohm.com (c) 2009 ROHM Co., Ltd. All rights reserved. 2/16 2009.04- Rev.B BD9701FP/CP-V5/T/T-V5,BD9703FP/CP-V5/T/T-V5,BD9702CP-V5/T/T-V5 Technical Note Electrical Characteristics BD9703FP/CP-V5/T/T-V5 (Unless otherwise noted, Ta=25,VCC=12V,Vo=5V,STBY=3V) Parameter Symbol Limit Unit Conditions MIN TYP MAX Ron - 1.0 1.5 design guarantee - 86 - % Io0.5A design guarantee fosc 270 300 330 kHz Load Regulation VOLOAD - 10 40 mV VCC=20V,Io=0.51.5A Line Regulation VOLINE - 40 100 mV VCC=1030V,Io=1.0A Over Current Protection Limit Iocp 1.6 - - A INV Pin Threshold Voltage VINV 0.98 1.00 1.02 V INV Pin Threshold Voltage Thermal Variation VINV - 0.5 - % Tj=085 design guarantee IINV - 1 - A VINV=1.0V ON VSTBYON 2.0 - 36 V OFF VSTBYOFF -0.3 - 0.3 V Istby 5 25 50 A Circuit Current Icc - 5 12 mA Stand-by Current Ist - 0 5 A Output ON Resistance Efficiency Switching Frequency INV Pin Input Current STBY Pin Threshold Voltage STBY Pin Input Current STBY=3V STBY0V Electrical Characteristics BD9702FP/CP-V5/T/T-V5 (Unless otherwise noted, Ta=25,VCC=12V,Vo=5V,STBY=3V) Parameter Symbol Limit Unit Conditions MIN TYP MAX Ron - 0.5 1.5 design guarantee - 86 - % Io1A design guarantee fosc 88 110 132 kHz Load Regulation VOLOAD - 10 40 mV VCC=20V,Io=13A Line Regulation VOLINE - 40 100 mV VCC=1030V,Io=1.0A Over Current Protection Limit Iocp 3.2 - - A INV Pin Threshold Voltage VINV 0.98 1.00 1.02 V INV Pin Threshold Voltage Thermal Variation VINV - 0.5 - % Tj=085 design guarantee IINV - 1 - A VINV=1.0V ON VSTBYON 2.0 - 36 V OFF VSTBYOFF -0.3 - 0.3 V Istby 5 25 50 A Circuit Current Icc - 4 12 mA Stand-by Current Ist - 0 5 A Output ON Resistance Efficiency Switching Frequency INV Pin Input Current STBY Pin Threshold Voltage STBY Pin Input Current www.rohm.com (c) 2009 ROHM Co., Ltd. All rights reserved. 3/16 STBY=3V STBY0V 2009.04- Rev.B BD9701FP/CP-V5/T/T-V5,BD9703FP/CP-V5/T/T-V5,BD9702CP-V5/T/T-V5 Technical Note Characteristic Data BD9701FP/CP-V5/T/T-V5 5 80 70 60 50 110 OSC FREQUENCY : FOSC [Hz] 90 OUTPUT VOLTAGE : VO [V] 6 EFFICIENCY : [%] 100 4 3 2 1 0 40 10 100 0 1000 1 2 3 105 100 95 90 -10 4 OUTPUT CURRENT IOUT : [A] OUTPUT CURRENT : IOUT[A] Fig.2 OCP VCC=20V Fig.1 EFFICIENCY-LOAD CURRENT 30 50 70 90 Fig.3 fosc-Ta 5.100 5.1 10 AMBIE NT T E MPE RAT URE : T a [ ] 5 VCC=30V 5.05 5 4.95 VCC=20V VCC=10V CIRCUIT CURRENT ; [mA] OUTPUT VOLTAGE : VO [V] 5.050 5.000 4.950 4.9 3 2.5 2 1.5 1 0 4.900 0 200 400 600 800 1000 0 10 20 30 10 40 INPUT VOLTAGE : VCC [V] OUTPUT CURRENT : IOUT[A] OSC FREQUENCY : FOSC [Hz] 3 2.5 2 1.5 1 0.5 0 0.5 1 1.5 105 100 95 2 SWITCHING CURRENT : ISW[A] Fig.7 VOUTOUT VOLTAGE-DRAIN CURRENT www.rohm.com (c) 2009 ROHM Co., Ltd. All rights reserved. 25 30 35 1.020 90 0 20 Fig.6 CIRCUIT CURRENT-INPUT VOLTAGE NO LOAD 110 3.5 15 INPUT VOLTAGE : VCC [V] Fig.5 OUTPUT VOLTAGE-INPUT VOLTAGE (Vo=5V,Ro=5ohm) Fig.4 OUTPUT VOLTAGE-LOAD CURRENT OUTPUT VOLTAGE : VDS[V] 4 3.5 0.5 0 10 20 30 INPUT VOLTAGE : VCC [V] Fig.8 fosc-INPUT VOLTAGE 4/16 40 INV THRESHOLD VOLTAGE : VINV[V] OUTPUT VOLTAGE : VO [V] 4.5 1.010 1.000 0.990 0.980 -10 10 30 50 70 AMBIENT TEMPERATURE : Ta [] Fig.9 INV THRESHOLD VOLTAGE-Ta 2009.04- Rev.B 90 BD9701FP/CP-V5/T/T-V5,BD9703FP/CP-V5/T/T-V5,BD9702CP-V5/T/T-V5 Technical Note Characteristic Data BD9702FP/CP-V5/T/T-V5 6 100 EFFICIENCY : [%] 80 70 60 50 [kHz] OSC FREQUENCY : FOSC OUTPUT VOLTAGE : VO [V] 120 90 5 4 3 2 1 0 40 10 100 1000 OUTPUT CURRENT : IOUT[A] 0 10000 1 5.10 4 5 VCC=20V 5.00 4.95 VCC=10V 4.90 500 1000 1500 2000 2500 5.00 4.95 10 20 30 40 Fig.13 OUTPUT VOLTAGE-LOAD CURRENT Fig.14 OUTPUT VOLTAGE-INPUT VOLTAGE (Vo=5V,Ro=5ohm) INV THRESHOLD VOLTAGE : VINV[V] OSC FREQUENCY : FOSC [Hz] 110 105 0.5 1 1.5 2 2.5 3 SWITCHING CURRENT : ISW[A] Fig.16 VOUTOUT VOLTAGE-DRAIN CURRENT www.rohm.com (c) 2009 ROHM Co., Ltd. All rights reserved. 2 1 15 20 25 30 35 Fig.15 CIRCUIT CURRENTINPUT VOLTAGE NO LOAD 1.01 1.00 0.99 0.98 100 0 3 1.02 115 0.0 90 INPUT VOLTAGE : VCC [V] 120 0.5 70 4 10 OUTPUT CURRENT : IOUT[A] 1.0 50 0 0 INPUT VOLTAGE : VCC [V] 1.5 30 5 5.05 3000 2.0 10 Fig.12 fosc-Ta 4.90 0 - 10 AMBIENT TEMPERATURE : Ta [] CIRCUIT CURRENT ; [mA] VCC=30V 5.05 105 100 6 5.10 OUTPUT VOLTAGE : VO [V] OUTPUT VOLTAGE : VO [V] 3 110 Fig.11 OCP VCC=20V Fig.10 EFFICIENCY-LOAD CURRENT OUTPUT VOLTAGE : VDS[V] 2 OUTPUT CURRENT : IOUT[A] 115 0 10 20 30 40 -10 10 30 50 70 INPUT VOLTAGE : VCC [V] AMBIENT TEMPERATURE : Ta [] Fig.17 fosc-INPUT VOLTAGE Fig.18 INV THRESHOLD VOLTAGE-Ta 5/16 2009.04- Rev.B 90 BD9701FP/CP-V5/T/T-V5,BD9703FP/CP-V5/T/T-V5,BD9702CP-V5/T/T-V5 Technical Note Characteristic Data BD9703FP/CP-V5/T/T-V5 100 6 80 70 60 50 OSC FREQUENCY : FOSC [Hz] OUTPUT VOLTAGE : VO [V] EFFICIENCY : [%] 90 330 5 4 3 2 1 0 40 10 100 0 1000 OUTPUT CURRENT : IOUT[A] 3 285 270 4 -10 Fig.21 fosc-Ta 5 OUTPUT VOLTAGE : VO [V] VCC=30V 5 VCC=20V 4.95 VCC=10V CIRCUIT CURRENT ; [mA] 5.10 5.05 5.05 5.00 4.95 200 400 600 800 0 1000 1.5 10 20 30 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 SWITCHING CURRENT : ISW[A] www.rohm.com (c) 2009 ROHM Co., Ltd. All rights reserved. 20 25 30 35 Fig.24 CIRCUIT CURRENT-INPUT VOLTAGE NO LOAD 1.02 315 300 285 270 0 10 20 30 INPUT VOLTAGE : VCC [V] Fig.25 VOUTOUT VOLTAGE-DRAIN CURRENT 15 INPUT VOLTAGE : VCC [V] INV THRESHOLD VOLTAGE : VINV[V] OSC FREQUENCY : FOSC [Hz] 0 1 10 40 330 0 2 Fig.23 OUTPUT VOLTAGE-INPUT VOLTAGE (Vo=5V,Ro=5ohm) Fig.22 OUTPUT VOLTAGE-LOAD CURRENT 0.5 3 INPUT VOLTAGE : VCC [V] OUTPUT CURRENT : IOUT[A] 1 4 0 4.90 4.9 0 10 30 50 70 90 AMBIENT TEMPERATURE : Ta [] Fig.20 OCP VCC=20V 5.1 OUTPUT VOLTAGE : VO [V] 2 300 OUTPUT CURRENT : IOUT[A] Fig.19 EFFICIENCY-LOAD CURRENT OUTPUT VOLTAGE : VDS[V] 1 315 Fig.26 fOSC-INPUT VOLTAGE 6/16 40 1.01 1.00 0.99 0.98 -10 10 30 50 70 90 AMBIENT TEMPERATURE : Ta [] Fig.27 INV THRESHOLD VOLTAGE-Ta 2009.04- Rev.B BD9701FP/CP-V5/T/T-V5,BD9703FP/CP-V5/T/T-V5,BD9702CP-V5/T/T-V5 Block Diagram BD9701FP/CP-V5/T/T-V5, BD9703FP/CP-V5/T-V5, BD9702CP-V5/T/T-V5 Technical Note VCC 1 TO252-5 Package Dimensions (mm) VREF PWM COMP DRIVER OSC STBY 5 STBY CTL LOGIC OUT 2 OCP TSD INV 4 Error AMP TO220CP-V5 Package Dimensions (mm) 3 GND Fig.28 Block Diagram Pin Description Pin No. Pin Name Function 1 VCC Input Power Supply Pin 2 OUT Internal Pch FET Drain Pin 3,FIN(*2) GND Ground 4 INV Output Voltage Feedback Pin 5 STBY ON/OFF Control Pin (*2)FIN is assigned in the case of TO252-5. TO220FP-5 Package Dimensions (mm) www.rohm.com (c) 2009 ROHM Co., Ltd. All rights reserved. TO220FP-5(V5) Package Dimensions (mm) 7/16 2009.04- Rev.B BD9701FP/CP-V5/T/T-V5,BD9703FP/CP-V5/T/T-V5,BD9702CP-V5/T/T-V5 Technical Note Block Function Explanations VREF Generates the regulated voltage from VCC input, compensated for temperature. OSC Generates the triangular wave oscillation frequency using an internal resistors and capacitor. Used for PWM comparator input. Error AMP This block, via the INV pin, detects the resistor-divided output voltage, compares this with the reference voltage, then amplifies and outputs the difference. PWM COMP Outputs PWM signals to the Driver block, which converts the error amp output voltage to PWM form. DRIVER This push-pull FET driver powers the internal Pch MOSFET, which accepts direct PWM input. STBY Controls ON/OFF operation via the STBY pin. The output is ON when STBY is High. Thermal Shutdown (TSD) This circuit protects the IC against thermal runaway and damage due to excessive heat. A thermal sensor detects the junction temperature and switches the output OFF once the temperature exceeds a threshold value (175deg). Hysteresis is built in (15deg) in order to prevent malfunctions due to temperature fluctuations. Over Current Protection (OCP) The OCP circuit detects the voltage difference between VCC and OUT by measuring the current through the internal Pch MOSFET and switches the output OFF once the voltage reaches the threshold value. The OCP block is a self-recovery type (not latch). Timing Chart OSC (Internal Oscillation Wave) Error AMP OUTPUT VCC PIN VOLTAGE WAVE OUTPIN VOLTAGE WAVE OUTPUT VOLTAGE WAVE Fig.29 www.rohm.com (c) 2009 ROHM Co., Ltd. All rights reserved. Timing Chart 8/16 2009.04- Rev.B BD9701FP/CP-V5/T/T-V5,BD9703FP/CP-V5/T/T-V5,BD9702CP-V5/T/T-V5 Technical Note Notes for PCB layout C5 R1 : 4kO R2 : 1kO C1 4 INV STBY 5 1 VCC OUT 2 L1 GND C2 3 5.0V D1 C4 C3 Fig.30 Layout * Place capacitors between VCC and Ground, and the Schottky diode as close as possible to the IC to reduce noise and maximize efficiency. * Connect resistors between INV and Ground, and the output capacitor filter at the same Ground potential in order to stabilize the output voltage. Application component selection and settings Inductor L1 If the winding resistance of the choke coil is too high, the efficiency may deteriorate. As the overcurrent protection operates over minimum 1.6A (BD9701FP/CP-V5/T/T-V5, BD9703FP/CP-V5/T-V5) or 3.2A minimum (BD9701CP-V5/T/T-V5), attention must be paid to the heating of the inductor due to overload of short-circulated load. Note that the current rating for the coil should be higher than IOUT(MAX)IL. Iout (MAX): maximum load current If you flow more than maximum current rating, coil will become overload, and cause magnetic saturation, and those account for efficiency deterioration. Select from enough current rating of coil which doesn't over peak current. VOUT (VCC-VOUT) IL. = x x 1 fosc L1 VCC L1:inductor value, VCC:maximum input voltage, VOUT:output voltage, IL:coil ripple current value, fosc:oscillation frequency Shottky Barrier Diodes D1 A Schottky diode with extremely low forward voltage should be used. Selection should be based on the following guidelines regarding maximum forward current, reverse voltage, and power dissipation: The maximum current rating is higher than the combined maximum load current and coil ripple current (IL). The reverse voltage rating is higher than the VIN value. Power dissipation for the selected diode must be within the rated level. The power dissipation of the diode is expressed by the following formula: Pdi=Iout(MAX)xVfx(1-VOUT/VCC) Iout (MAX): maximum load current, Vf: forward voltage, VOUT: output voltage, VCC: input voltage Capacitor C1,C2,C3,C4,C5 As large ripple currents flow across C1 and C3 capacitors, high frequency and low impedance capacitor for a switching regulator must be used. The ceramic capacitor C2 must be connected. If not, noise may cause an abnormal operation. If the ripple voltage of input and output is large, C4 selected among ceramic , tantalum and OS capacitor with low ESR may decrease the ripple, however if the only low ESR capacitor is used, an oscillation or unstable operation may be caused. C5 is the capacitor for phase compensation and normally not used. If you need to improve the stability of feedback network, connect C5 between INV and OUTPUT. Feed back resistance R1,R2 The offset of output voltage is determined by both Feed back resistance and INV pin input current. VOUT=(R1+R2) VINV/R2 (VINV pin Threshold Votage) If Feed back resistance is high, the setting of output voltage will be move. Recommended : Resistance between INV pin and GND = less than 10k. www.rohm.com (c) 2009 ROHM Co., Ltd. All rights reserved. 9/16 2009.04- Rev.B BD9701FP/CP-V5/T/T-V5,BD9703FP/CP-V5/T/T-V5,BD9702CP-V5/T/T-V5 Technical Note Recommended Circuit C2 + C1 1 VCC OUT L1 2 5.0V D1 C4 + C3 STBY 5 R1 : 4k C5 INV 4 R2 : 1k 3 GND Fig.31 Recommended Circuit Output Voltage 5V : Application cicuit example (BD9701FP/CP-V5/T/T-V5) Recommended Components (Example) Inductor L1100H Schottky Diode D1 Capacitor C1100F(50V) C2OPEN C3220F(25V) C4OPEN C5OPEN Recommended Components example 2 Inductor L1100H Schotky Diode D1 Capacitor C1220F(25V) C21.0F(50V) C3470F(16V) C4150F(20V) C3OPEN www.rohm.com (c) 2009 ROHM Co., Ltd. All rights reserved. :CDRH127/LD (sumida) :RB050LA-40 (ROHM) :Al electric capacitor UHD1H101MPT (nichicon) :Al electric capacitor UHD1E221MPT (nichicon) :CDRH127/LD (sumida) :RB050LA-40 (ROHM) :Al electric capacitor UVR1H221MPA (nichicon) :ceramic cap UMK212F105ZG (TAIYO YUDEN) :Al electric capacitor UVR1E471MPA (nichicon) :OS capacitor 20SVP150M (SANYO) 10/16 2009.04- Rev.B BD9701FP/CP-V5/T/T-V5,BD9703FP/CP-V5/T/T-V5,BD9702CP-V5/T/T-V5 Technical Note (BD9703FP/CP-V5/T/T-V5) Recommended Components Inductor L147H Schotky Diode D1 Capacitor C1100F(50V) C22.2F(50V) C3470F(25V) C4OPEN C3OPEN :CDRH127/LD (sumida) :RB050LA-40 (ROHM) :Al electric capacitor UHD1H101MPT (nichicon) :ceramic cap CM43X7R225K50A (KYOCERA) :Al electric capacitor UHD1E471MPT (nichicon) (BD9702CP-V5/T/T-V5) Recommended Components Inductor L147H Schotky Diode D1 Capacitor C11000F(50V) C2OPEN C31000F(25V) C4OPEN C3OPEN :CDRH127/LD (sumida) :RB050LA-40 (ROHM) :Al electric capacitor UHD1H102MPT (nichicon) :Al electric capacitor UHD1E102MPT (nichicon) Test Circuit Vcc 1 OUT 2 GND INV 4 3 SW2 + STBY 5 SW4 Icc A A I INV 1k Vcc 2k A V INV + f SW5 ISTB VSTB SW6 V Vo Io Fig.32 Input Output Measurement Circuit www.rohm.com (c) 2009 ROHM Co., Ltd. All rights reserved. 11/16 2009.04- Rev.B BD9701FP/CP-V5/T/T-V5,BD9703FP/CP-V5/T/T-V5,BD9702CP-V5/T/T-V5 Technical Note I/O Equivalent Circuit Pin 1 (VCC), Pin 3 (GND) Pin 2 (OUT) Pin 4 (INV) Pin 5 (STBY) VC VCC VCC STB VCC OUT INV 300 140K 60K GND 70K Fig.33Input Output Equivalent Circuit Notes for use 1. Absolute Maximum Ratings Use of the IC in excess of absolute maximum ratings such as the applied voltage or operating temperature range may result in IC deterioration or damage. Assumptions should not be made regarding the state of the IC (short mode or open mode) when such damage is suffered. A physical safety measure such as a fuse should be implemented when use of the IC in a special mode where the absolute maximum ratings may be exceeded is anticipated. 2. GND voltage Ensure a minimum GND pin potential in all operating conditions. In addition, ensure that no pins other than the GND pin carry a voltage lower than or equal to the GND pin, including during actual transient phenomena. 3. Thermal design Use a thermal design that allows for a sufficient margin in light of the power dissipation (Pd) in actual operating conditions. 4. Inter-pin shorts and mounting errors Use caution when orienting and positioning the IC for mounting on printed circuit boards. Improper mounting may result in damage to the IC. Shorts between output pins or between output pins and the power supply and GND pin caused by the presence of a foreign object may result in damage to the IC. 5. Operation in strong electromagnetic field Operation in a strong electromagnetic field may cause malfunction. 6. Thermal shutdown circuit (TSD circuit) This IC incorporates a built-in thermal shutdown circuit (TSD circuit). The TSD circuit is designed only to shut the IC off to prevent runaway thermal operation. Do not continue to use the IC after operating this circuit or use the IC in an environment where the operation of the thermal shutdown circuit is assumed. 7. Testing on application boards When testing the IC on an application board, connecting a capacitor to a pin with low impedance subjects the IC to stress. Always discharge capacitors after each process or step. Ground the IC during assembly steps as an antistatic measure, and use similar caution when transporting or storing the IC. Always turn the IC's power supply off before connecting it to or removing it from a jig or fixture during the inspection process. www.rohm.com (c) 2009 ROHM Co., Ltd. All rights reserved. 12/16 2009.04- Rev.B BD9701FP/CP-V5/T/T-V5,BD9703FP/CP-V5/T/T-V5,BD9702CP-V5/T/T-V5 Technical Note 8. IC pin input This IC is a monolithic IC which (as below) has P+ substrate and betweenthe various pin. A P-N junction is formed from this P layer of each pin. For example the relation between each potential is as follows. (When GND > PinB and GND > PinA, the P-N junction operates as a parasitic diode.) Parasitic diodes can occur inevitably in the structure of the IC. The operation of parasitic diodes can result in mutual interference among circuits as well as operation faults and physical damage. Accordingly, you must not use methods by which parasitic diodes operate, such as applying a voltage that is lower than the GND(P substrate)voltage to an input pin. (PinB) (PinA) Transistor (NPN) B Resistance E GND N P P N P P P N N N N P substrate P substrate Parasitic diode P GND Parasitic diode (PinB) (PinA) C Parasitic diode B E GND GND Other adjacent components Parasitic diode Fig.34 Simplified structure of a Bipolar IC 9. Common impedance Power supply and ground wiring should reflect consideration of the need to lower common impedance and minimize ripple as much as possible (by making wiring as short and thick as possible or rejecting ripple by incorporating inductance and capacitance). 10. Pin short and mistake fitting Do not short-circuit between OUT pin and VCC pin, OUT pin and GND pin, or VCC pin and GND pin. When soldering the IC on circuit board, please be unusually cautious about theorientation and the position of the IC. Bypass diode Back current prevention diode VCC Output Pin Fig.35 www.rohm.com (c) 2009 ROHM Co., Ltd. All rights reserved. 13/16 2009.04- Rev.B BD9701FP/CP-V5/T/T-V5,BD9703FP/CP-V5/T/T-V5,BD9702CP-V5/T/T-V5 Technical Note 11. Application circuit Although we can recommend the application circuits contained herein with a relatively high degree of confidence, we ask that you verify all characteristics and specifications of the circuit as well as performance under actual conditions. Please note that we cannot be held responsible for problems that may arise due to patent infringements or noncompliance with any and all applicable laws and regulations. 12. Operation The IC will turn ON when the voltage at the STBY pin is greater than 2.0V and will switch OFF if under 0.3V. Therefore, do not input voltages between 0.3V and 2.0V. Malfunctions and/or physical damage may occur. Power Dissipation TO252-S (4) 4.80W POWER DISSIPATION : Pd [W] 5 4 (1) No heat sink (2) 2layer PCB (Copper laminate area 15 mmx15mm) (3) 2layer PCB (Copper laminate area 70 mmx70mm) (4) 4layer PCB (Copper laminate area 70 mmx70mm) (3) 3.50W 3 (2) 1.85W 2 (1) 0.80W 1 0 0 25 50 75 85 100 125 AMBIENT TEMPERATURE : Ta[C] 150 Fig.36 TO220 POWER DISSIPATION : Pd [W] 15 (1) No heat sink (2) Aluminum heat sink 3 50x50x2 (mm ) (3) Aluminum heat sink 100x100x2 (mm3) (3) 11.0W 10 (2) 6.5W 5 (1) 2.0W 0 0 25 50 75 100 125 AMBIENT TEMPERATURE : Ta[C] 150 Fig.37 www.rohm.com (c) 2009 ROHM Co., Ltd. All rights reserved. 14/16 2009.04- Rev.B BD9701FP/CP-V5/T/T-V5,BD9703FP/CP-V5/T/T-V5,BD9702CP-V5/T/T-V5 Technical Note Ordering part number B D 9 Part No. 7 0 1 F Part No. 9701=36V/1.5A 9702=36V/1.5A 9703=36V/3.0A P - Package FP : TO252-5 CP-V5 : TO220CP-V5 T/T-V5 : TO220FP-5(V5) E 2 Packaging and forming specification E2: Embossed tape and reel None:Tray,Tube Package specifications TO252-5 <Tape and Reel information> 2.30.2 6.50.2 C0.5 1.50.2 +0.2 5.1 -0.1 0.50.1 Tape Embossed carrier tape Quantity 2000pcs Direction of feed The direction is the 1pin of product is at the lower left when you hold ( reel on the left hand and you pull out the tape on the right hand ) 1.5 4 5 0.8 1 2 3 2.5 9.50.5 5.50.2 FIN E2 0.50.1 0.5 1.27 1.00.2 1pin Reel (Unit : mm) Direction of feed Order quantity needs to be multiple of the minimum quantity. <Tape and Reel information> +0.3 4.5 -0.1 +0.2 2.8 -0.1 3.20.1 Container Tube Quantity 500pcs Direction of feed Direction of products is fixed in a container tube 8.00.2 0.7 +0.4 17.0 -0.2 +0.3 10.0-0.1 +0.3 7.0 -0.1 13.5Min. 12.00.2 1.80.2 TO220FP-5 1.2 0.8 1.778 0.50.1 2.85 1 2 3 4 5 Order quantity needs to be multiple of the minimum quantity. (Unit : mm) www.rohm.com (c) 2009 ROHM Co., Ltd. All rights reserved. 15/16 2009.04- Rev.B BD9701FP/CP-V5/T/T-V5,BD9703FP/CP-V5/T/T-V5,BD9702CP-V5/T/T-V5 Technical Note 23.4 (2.0) 3.20.1 <Tape and Reel information> +0.2 2.8 -0.1 17.5 +0.3 4.5 -0.1 0.3 7.0 + - 0.1 Container Tube Quantity 500pcs Direction of feed Direction of products is fixed in a container tube 25.8 + 0.3 10.0 - 0.1 8.00.2 0.7 +0.4 17.0 -0.2 12.00.2 31.5Max. 1.80.2 TO220FP-5(V5) 1.2 0.8 0.50.1 1.778 (2.85) 4.25 8.15 1 2 3 4 5 Order quantity needs to be multiple of the minimum quantity. (Unit : mm) TO220CP-V5 1.444 <Tape and Reel information> 4.50.1 (1.0) 0.820.1 0.92 1.778 Tape Embossed carrier tape Quantity 500pcs E2 Direction of feed The direction is the 1pin of product is at the lower left when you hold ( reel on the left hand and you pull out the tape on the right hand ) 16.92 13.60 +0.2 2.8 -0.1 8.0 0.2 1.0 0.2 4.92 0.2 12.0 0.2 +0.4 15.2 -0.2 +0.3 3.20.1 10.0 -0.1 0.420.1 1.58 (2.85) 4.12 (Unit : mm) www.rohm.com (c) 2009 ROHM Co., Ltd. All rights reserved. Reel 16/16 1pin Direction of feed Order quantity needs to be multiple of the minimum quantity. 2009.04- Rev.B Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com (c) 2009 ROHM Co., Ltd. All rights reserved. R0039A