Datasheet 200-mA 3.3-V or 5.0-V Output LDO Regulators BD4xxM2-C Series General Description Features The BD4xxM2-C series are low quiescent regulators featuring 45 V absolute maximum voltage, and output voltage accuracy of 2 % ( 3.3 V or 5.0 V: Typ.), 200 mA output current and 40 A (Typ.) current consumption. These regulators are therefore ideal for applications requiring a direct connection to the battery and a low current consumption. A logical "HIGH" at the CTL pin enables the device and "LOW" at the CTL pin not enables the device. (Only W: Includes switch) Ceramic capacitors can be used for compensation of the output capacitor phase. Furthermore, these ICs also feature overcurrent protection to protect the device from damage caused by short-circuiting and an integrated thermal shutdown to protect the device from overheating at overload conditions. Packages EFJ: HTSOP-J8 Qualified for Automotive Applications Wide Temperature Range: -40 C to +150 C Wide Operating Input Range: 3.0 V to 42 V Low Quiescent Current: 40 A (Typ.) Output Current: 200 mA High Output Voltage Accuracy: 2 % Output Voltage: 3.3 V or 5.0 V (Typ.) Enable Input (Only W: Includes Enable Input) Over Current Protection (OCP) Thermal Shutdown Protection (TSD) (Note1) AEC-Q100 Qualified (Note1:Grade1) W (Typ.) x D (Typ.) x H (Max.) (Note2) FP3: SOT223-4(F) 4.90 mm x 6.00 mm x 1.00 mm 6.53 mm x 7.00 mm x 1.80mm (Note2: SOT223-4 & SOT223-4F) Figure 1. Package Outlook Applications Automotive (body, audio system, navigation system, etc.) Typical Application Circuits Components externally connected: 0.1 F CIN, 10 F COUT (Typ.) *Electrolytic, Tantalum and Ceramic capacitors can be used. 4:GND 8:VCC 7:N.C. 6:N.C. 5:GND BD4xxM2WFP3-C CIN BD4xxM2EFJ-C 1:VOUT 2:N.C. 3:N.C. 1:VCC 2:CTL 3:VOUT 4:N.C. CIN COUT COUT BD433 / 450M2EFJ-C BD433 / 450M2WEFJ-C BD433 / 450M2WFP3-C HTSOP-J8 Figure 2. Typical Application Circuits Product structureSilicon monolithic integrated circuit www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211114001 BD433 / 450M2FP3-C SOT223-4(F) This product is not designed protection against radioactive rays 1/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series Ordering Information B D 4 Part Number x x M 2 W E F J C Output Voltage Output Current Enable Input Package 33: 3.3 V 50: 5.0 V 2: 200 mA W: Includes Enable Input EFJ: HTSOP-J8 FP3: SOT223-4(F) E2 Packaging and Forming Specification E2: Embossed Tape and Reel Lineup Output Current Ability Output Voltage (Typ.) Enable Input *1 Package Type Orderable Part Number SOT223-4(F) BD433M2WFP3-CE2 HTSOP-J8 BD433M2WEFJ-CE2 SOT223-4(F) BD433M2FP3-CE2 HTSOP-J8 BD433M2EFJ-CE2 SOT223-4(F) BD450M2WFP3-CE2 HTSOP-J8 BD450M2WEFJ-CE2 SOT223-4(F) BD450M2FP3-CE2 HTSOP-J8 BD450M2EFJ-CE2 3.3 V 200 mA 5.0 V *1 : Includes Enable Input. : Not includes Enable Input. www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 2/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series Pin Configurations HTSOP-J8 (Top View) SOT223-4(F) (Top View) 4 (FIN) 1 2 3 Figure 3. Pin Configuration Pin Descriptions BD433 / 450M2WEFJ-C BD433 / 450M2WFP3-C Pin No. Pin Name Function Pin No. Pin Name Function 1 VOUT Output pin 1 VCC Supply Voltage Input Pin 2 N.C. Not Connected 2 CTL Output Control Pin 3 N.C. Not Connected 3 VOUT Output Pin 4 N.C. Not Connected 4 (FIN) GND Ground Pin 5 GND Ground Pin 6 N.C. Not Connected 7 CTL Output Control Pin 8 VCC Supply Voltage Input Pin BD433 / 450M2EFJ-C BD433 / 450M2FP3-C Pin No. Pin Name Function Pin No. Pin Name Function 1 VOUT Output Pin 1 VCC Supply Voltage Input Pin 2 N.C. Not Connected 2 GND Ground Pin 3 N.C. Not Connected 3 VOUT Output Pin 4 N.C. Not Connected 4 (FIN) GND Ground Pin 5 GND Ground Pin 6 N.C. Not Connected 7 N.C. Not Connected 8 VCC Supply Voltage Input Pin * N.C. Pin is recommended to short with GND. * N.C. Pin can be open because it isn't connect it inside of IC. * Exposed die pad is need to be connected to GND. www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 3/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series Block Diagrams BD433 / 450M2WEFJ-C BD433 / 450M2EFJ-C VCC (8PIN) N.C. (7PIN) PREREG N.C. (6PIN) GND (5PIN) VREF DRIVER OCP TSD VOUT (1PIN) www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 N.C. (3PIN) N.C. (2PIN) 4/34 N.C. (4PIN) TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series BD433 / 450M2WFP3-C GND (FIN) CTL PREREG VREF DRIVER OCP TSD VCC (1PIN) CTL (2PIN) BD433 / 450M2FP3-C VOUT (3PIN) GND (FIN) PREREG VREF DRIVER OCP TSD VCC (1PIN) GND (2PIN) VOUT (3PIN) Figure 4. Block Diagrams www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 5/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series Description of Blocks Block Name Function Description of Blocks CTL *1 Control Output Voltage ON/OFF A logical "HIGH" ( 2.8 V ) at the CTL pin enables the device and "LOW" ( 0.8 V ) at the CTL pin not enable the device. PREREG Internal Power Supply TSD Thermal Shutdown Protection VREF Reference Voltage DRIVER Output MOS FET Driver Drive the Output MOS FET OCP Over Current Protection To protect the device from damage caused by over current. If the output current reaches ca. 550 mA ( Typ.), the output is turned off. Power Supply for Internal Circuit To protect the device from overheating. If the chip temperature ( Tj ) reaches ca. 175 C ( Typ. ), the output is turned off. Generate the Reference Voltage *1 Applicable for product with Enable Input. www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 6/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series Absolute Maximum Ratings Parameter Symbol Ratings Unit Supply Voltage *1 VCC -0.3 to +45.0 V Output Control Voltage *2 CTL -0.3 to +45.0 V VOUT -0.3 to +8.0 V HTSOP-J8 *3 Pd 0.75 W SOT223-4(F) *3 Pd 0.60 W Junction Temperature Range Tj -40 to +150 C Storage Temperature Range Tstg -55 to +150 C Tjmax +150 C VESD,HBM 2000 V Output Voltage Power Dissipation Maximum Junction Temperature ESD withstand Voltage (HBM) *1 *2 *4 *3 Do not exceed Pd. Applicable for product with Enable Input. The start up orders of power supply (VCC) and the CTL pin do not influence if the voltage is within the operation power supply voltage range. HTSOP-J8 mounted on 114.3 mm x 76.2 mm x 1.6 mmt Glass-Epoxy PCB based on JEDEC. If Ta 25 C, reduce by 6.0 mW/C. (1-layer PCB: Copper foil area on the reverse side of PCB:0 mm x 0 mm) SOT223-4(F) mounted on 114.3 mm x 76.2 mm x 1.6 mmt Glass-Epoxy PCB based on JEDEC. If Ta 25 C, reduce by 4.8 mW/C. (1-layer PCB: Copper foil area on the reverse side of PCB:0 mm x 0 mm) *4 ESD susceptibility Human Body Model "HBM" Operating Conditions (-40 C Tj +150 C) Parameter Symbol Min. Max. Unit Supply Voltage ( IOUT 200 mA ) *1 VCC 4.3 42.0 V Supply Voltage ( IOUT 100 mA ) *1 VCC 3.9 42.0 V Supply Voltage ( IOUT 200 mA ) *2 VCC 5.8 42.0 V Supply Voltage ( IOUT 100 mA ) *2 VCC 5.5 42.0 V Output Control Voltage *3 CTL 0 42.0 V Start-Up Voltage *4 VCC 3.0 V IOUT 0 200 mA Tj -40 +150 C Output Current Junction Temperature Range *1 *2 *3 *4 BD433M2WEFJ-C / BD433M2WFP3-C / BD433M2EFJ-C / BD433M2FP3-C BD450M2WEFJ-C / BD450M2WFP3-C / BD450M2EFJ-C / BD450M2FP3-C Applicable for product with Enable Input When IOUT = 0 mA www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 7/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series Thermal Resistance Parameter Symbol Min. Max. Unit HTSOP-J8 Package Junction to Ambient *1 ja 43.1 C/W Junction to Case (bottom) *1 jc 10 C/W Junction to Ambient *2 ja 83.3 C/W Junction to Case (bottom) *2 jc 17 C/W SOT223-4(F) Package *1 HTSOP-J8 mounted on 114.3 mm x 76.2 mm x 1.6 mmt Glass-Epoxy PCB based on JEDEC. (4-layer PCB: Copper foil on the reverse side of PCB:74.2 mm x 74.2 mm) *2 SOT223-4(F) mounted on 114.3 mm x 76.2 mm x 1.6 mmt Glass-Epoxy PCB based on JEDEC. (4-layer PCB: Copper foil on the reverse side of PCB:74.2 mm x 74.2 mm) www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 8/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series Electrical Characteristics (Unless otherwise specified, -40 C Tj +150 C, VCC = 13.5 V, CTL = 5 V(*1), IOUT = 0 mA. The typical value is defined at Tj = 25 C.) Limit Parameter Symbol Unit Min. Typ. Max. Shut Down Current Ishut *1 Conditions CTL = 0 V, Tj 125 C IOUT = 0 mA, Tj 125 C IOUT 200 mA, Tj 150 C 6 V VCC 42 V, 0 mA IOUT 50 mA 6 V VCC 42 V, IOUT 200 mA 6 V VCC 42 V, 0 mA IOUT 50 mA 6 V VCC 42 V, IOUT 200 mA VCC = VOUT x 0.95 (= 4.75V: Typ.), IOUT = 100 mA VCC = VOUT x 0.95 (= 3.135V: Typ.), IOUT = 100 mA f = 120 Hz, ein = 1 Vrms, IOUT = 100 mA 2.0 5.0 A 40 90 A 40 150 A 4.90 5.00 5.10 V 4.80 5.00 5.10 V 3.23 3.30 3.37 V 3.16 3.30 3.37 V Vd *2 0.16 0.35 V Vd *3 0.20 0.45 V Ripple Rejection R.R. 55 65 dB Line Regulation Reg.I 10 30 mV 8 V VCC 16 V Load Regulation Reg.L 10 30 mV 10 mA 100 mA TSD 175 C Tj at TSD ON Circuit Current Icc VOUT *2 Output Voltage VOUT *3 Dropout Voltage Thermal Shut Down *1 *2 *3 Applicable for product with Enable Input. For BD450M2WEFJ-C / BD450M2WFP3-C / BD450M2EFJ-C / BD450M2FP3-C For BD433M2WEFJ-C / BD433M2WFP3-C / BD433M2EFJ-C / BD433M2FP3-C Electrical Characteristics ( Enable function * Applicable for product with Enable Input. ) (Unless otherwise specified, -40 C Tj +150 C, VCC = 13.5 V, IOUT = 0 mA. The Typical value is defined at Tj = 25 C.) Limit Parameter Symbol Unit Conditions Min. Typ. Max. CTL ON Mode Voltage VthH 2.8 V ACTIVE MODE CTL OFF Mode Voltage VthL 0.8 V OFF MODE CTL Bias Current ICTL 15 30 A CTL = 5 V www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 9/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series Typical Performance Curves BD433M2WEFJ-C / BD433M2EFJ-C / BD433M2WFP3-C / BD433M2FP3-C Reference Data Unless otherwise specified: -40 C Tj +150 C, VCC = 13.5 V, CTL = 5 V (*1), IOUT = 0 mA. *1 Applicable for product with Enable Input. 100 6 Tj = -40 C 90 Tj = 25 C 5 Output Voltage: VOUT[V] Circuit Current: Icc[A] 80 Tj = 125 C 70 60 50 40 30 4 3 2 Tj = -40 C 20 Tj = 25 C 1 10 Tj = 125 C 0 0 5 10 15 20 25 30 35 40 0 45 0 5 10 Supply Voltage: VCC[V] 40 45 Figure 6. Output Voltage vs. Power Supply Voltage (IOUT = 0 mA) Figure 5. Circuit Current vs. Power Supply Voltage 6 100 Tj = -40 C 90 Tj = 25 C 5 Output Voltage: VOUT[V] 80 Circuit Current: Icc[A] 15 20 25 30 35 Supply Voltage: VCC[V] Tj = 125 C 70 60 50 40 30 4 3 2 Tj = -40 C 20 1 Tj = 25 C 10 Tj = 125 C 0 0 0 1 2 3 4 5 6 7 8 9 10 Supply Voltage: VCC[V] 1 2 3 4 Supply Voltage: VCC[V] 5 6 Figure 8. Output Voltage vs. Power Supply Voltage (IOUT = 0 mA) *magnified Figure 6. at low supply voltage Figure 7. Circuit Current vs. Power Supply Voltage *magnified Figure 5. at low supply voltage www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 0 10/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series Typical Performance Curves BD433M2WEFJ-C / BD433M2EFJ-C / BD433M2WFP3-C / BD433M2FP3-C Reference Data Unless otherwise specified: -40 C Tj +150 C, VCC = 13.5 V, CTL = 5 V (*1), IOUT = 0 mA. 6 6 5 5 Output Voltage: VOUT[V] Output Voltage: VOUT[V] *1 Applicable for product with Enable Input. 4 3 2 Tj = -40 C Tj = 25 C 1 4 3 2 Tj = -40 C 1 Tj = 25 C Tj = 125 C Tj = 125 C 0 0 0 5 10 15 20 25 30 35 Supply Voltage: VCC[V] 40 0 45 200 300 400 500 600 700 Output Current: IOUT[mA] Figure 9. Output Voltage vs. Power Supply Voltage (IOUT = 10 mA) Figure10. Output Voltage vs. Output Current (Over Current Protection) 90 0.8 Tj = -40 C 0.7 80 Tj = 25 C Tj = 125 C 0.6 Repple Rejection: R.R.[dB] Dropout Voltage: Vd[V] 100 0.5 0.4 0.3 0.2 70 60 50 40 30 20 Tj = -40 C Tj = 25 C 0.1 10 0 0 20 40 60 80 100 120 140 160 180 200 Output Current: IOUT[mA] Figure 11. Dropout Voltage (VCC = 3.135 V) www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 0 0.01 Tj = 125 C 0.1 1 Frequency: f [kHz] 10 100 Figure 12. Ripple Rejection (ein = 1 Vrms, IOUT = 100 mA) 11/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series Typical Performance Curves BD433M2WEFJ-C / BD433M2EFJ-C / BD433M2WFP3-C / BD433M2FP3-C Reference Data Unless otherwise specified: -40 C Tj +150 C, VCC = 13.5 V, CTL = 5 V (*1), IOUT = 0 mA. *1 Applicable for product with Enable Input. 6 90 Tj = -40 C 80 5 Tj = 25 C Tj = 125 C Output Voltage: VOUT[V] Circuit Current: Icc[A] 70 60 50 40 30 4 3 2 20 1 10 0 0 0 40 80 120 160 200 100 120 140 160 180 200 Junction Temperature: Tj[C] Output Current: IOUT[mA] Figure 14. Output Voltage vs. Temperature (Thermal Shut Down) Figure 13. Circuit Current vs. Output Current 100 3.370 90 3.350 3.330 Circuit Current: Icc[A] Output Voltage: VOUT[V] 80 3.310 3.290 3.270 70 60 50 40 30 20 3.250 10 0 3.230 -40 0 40 80 120 160 Junction Temperature: Tj[C] 0 20 40 60 80 100 120 140 160 Junction Temperature: Tj[C] Figure 15. Output Voltage vs. Temperature www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 -40 -20 Figure 16. Circuit Current vs. Temperature 12/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series Typical Performance Curves BD433M2WEFJ-C / BD433M2WFP3-C Reference Data Unless otherwise specified: -40 C Tj +150 C, VCC = 13.5 V, IOUT = 0 mA 6 9 Tj = -40 C 8 Tj = 25 C 7 Tj = 125 C 5 Output Voltage: VOUT[V] Shutdown Current: Ishut[A] 10 6 5 4 3 2 4 3 2 1 1 Tj = -40 C 0 0 5 10 15 20 25 30 35 Supply Voltage: VCC[V] 40 0 45 0 6 6 5 5 4 3 2 2 3 4 CTL Supply Voltage: CTL[V] 5 Figure 18. CTL ON / OFF Mode Voltage (Tj = -40 C) Output Voltage: VOUT[V] Output Voltage: VOUT[V] Figure 17. Shut Down Current vs. Power Supply Voltage (CTL = 0 V) 1 4 3 2 1 1 Tj = 25 C Tj = 125 C 0 0 0 1 2 3 4 CTL Supply Voltage: CTL[V] 5 1 2 3 4 CTL Supply Voltage: CTL[V] 5 Figure 20. CTL ON / OFF Mode Voltage (Tj = 125 C) Figure 19. CTL ON / OFF Mode Voltage (Tj = 25 C) www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 0 13/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series Typical Performance Curves BD433M2WEFJ-C / BD433M2WFP3-C Reference Data Unless otherwise specified: -40 C Tj +150 C, VCC = 13.5 V, IOUT = 0 mA 5 30 25 4 CTL Bias Current: ICTL[A] Shutdown Current: Ishut[A] Tj = -40 C 3 2 1 Tj = 25 C Tj = 125 C 20 15 10 5 0 -40 0 40 80 120 Junction Temperature: Tj[C] 160 0 1 2 3 4 5 CTL Supply Voltage: CTL[V] Figure 21. Shut Down Current vs. Temperature (CTL = 0 V) www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 0 Figure 22. CTL Bias Current vs. CTL Supply Voltage 14/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series Typical Performance Curves BD450M2WEFJ-C / BD450M2EFJ-C / BD450M2WFP3-C / BD450M2FP3-C Reference Data Unless otherwise specified: -40 C Tj +150 C, VCC = 13.5 V, CTL = 5V (*1), IOUT = 0 mA *1 Applicable for product with Enable Input. 100 6 90 5 70 Output Voltage: VOUT[V] Circuit Current: Icc[A] 80 60 50 40 30 Tj = -40 C 20 Tj = 25 C 10 3 2 Tj = -40 C 1 Tj = 25 C Tj = 125 C Tj = 125 C 0 0 0 5 10 15 20 25 30 35 40 45 0 5 10 15 20 25 30 35 40 45 Supply Voltage: VCC[V] Supply Voltage: VCC[V] Figure 23. Circuit Current vs. Power Supply Voltage Figure 24. Output Voltage vs. Power Supply Voltage (IOUT = 0 mA) 100 6 90 Tj = -40 C 80 Tj = 25 C 70 Tj = 125 C 5 Output Voltage: VOUT[V] Circuit Current: Icc[A] 4 60 50 40 30 20 4 3 2 Tj = -40 C 1 Tj = 25 C 10 Tj = 125 C 0 0 0 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 Supply Voltage: VCC[V] Supply Voltage: VCC[V] Figure 26. Output Voltage vs. Power Supply Voltage (IOUT = 0 mA) *magnified Figure 24. at low supply voltage Figure 25. Circuit Current vs. Power Supply Voltage *magnified Figure 23. at low supply voltage www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 0 15/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series Typical Performance Curves BD450M2WEFJ-C / BD450M2EFJ-C / BD450M2WFP3-C / BD450M2FP3-C Reference Data Unless otherwise specified: -40 C Tj +150 C, VCC = 13.5 V, CTL = 5V (*1), IOUT = 0 mA 6 6 5 5 Output Voltage: VOUT[V] Output Voltage: VOUT[V] *1 Applicable for product with Enable Input. 4 3 2 Tj = -40 C 1 4 3 2 Tj = -40 C 1 Tj = 25 C Tj = 25 C Tj = 125 C Tj = 125 C 0 0 0 5 10 15 20 25 30 35 40 0 45 200 300 400 500 600 700 Output Current: IOUT: [mA] Supply Voltage: VCC[V] Figure 28. Output Voltage vs. Output Current (Over Current Protection) Figure 27. Output Voltage vs. Power Supply Voltage (IOUT = 10 mA) 0.8 90 Tj = -40 C 0.7 80 0.6 Repple Rejection: R.R.[dB] Tj = 25 C Dropout Voltage: Vd[V] 100 Tj = 125 C 0.5 0.4 0.3 0.2 70 60 50 40 30 20 Tj = -40 C Tj = 25 C 0.1 10 0 0 20 40 60 80 100 120 140 160 180 200 Output Current: IOUT[mA] Tj = 125 C 0.1 1 10 Frequwncy: f [kHz] 100 Figure 30. Ripple Rejection (ein = 1 Vrms, IOUT = 100 mA) Figure 29. Dropout Voltage (VCC = 4.75 V) www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 0 0.01 16/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series Typical Performance Curves BD450M2WEFJ-C / BD450M2EFJ-C / BD450M2WFP3-C / BD450M2FP3-C Reference Data Unless otherwise specified: -40 C Tj +150 C, VCC = 13.5 V, CTL = 5V (*1), IOUT = 0 mA *1 Applicable for product with Enable Input. 90 6 Tj = -40 C 80 Tj = 25 C 5 Tj = 125 C Output Voltage: VOUT[V] Circuit Current: Icc[A] 70 60 50 40 30 20 4 3 2 1 10 0 0 40 80 120 160 0 200 100 120 Output Current: IOUT[mA] 5.080 90 5.060 80 5.040 70 Circuit Current: Icc[A] Output Voltage: VOUT[V] 100 5.020 5.000 4.980 4.960 50 40 30 20 4.920 10 4.900 40 60 80 100 120 140 160 Junction Temperature: Tj[] 0 -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature: Tj[C] Figure 34. Circuit Current vs. Temperature Figure 33. Output Voltage vs. Temperature www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 200 60 4.940 20 180 Figure 32. Output Voltage vs. Temperature (Thermal Shut Down) 5.100 0 160 Junction Temperature: Tj[C] Figure 31. Circuit Current vs. Output Current -40 -20 140 17/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series Typical Performance Curves BD450M2WEFJ-C / BD450M2WFP3-C Reference Data Unless otherwise specified: -40 C Tj +150 C, VCC = 13.5 V, IOUT = 0 mA 6 9 Tj = -40 C 8 Tj = 25 C 7 Tj = 125 C 5 Output Voltage: VOUT[V] Shutdown Current: Ishut[A] 10 6 5 4 3 2 4 3 2 1 Tj = -40 C 1 0 0 0 5 10 15 20 25 30 35 Supply Voltage: VCC[V] 40 0 45 6 6 5 5 4 3 2 2 3 4 CTL Supply Voltage: CTL[V] 5 Figure 36. CTL ON / OFF Mode Voltage (Tj = -40 C) Output Voltage: VOUT[V] Output Voltage: VOUT[V] Figure 35. Shut Down Current vs. Power Supply Voltage (CTL = 0 V) 1 4 3 2 1 1 Tj = 125 C Tj = 25 C 0 0 0 1 2 3 4 CTL Supply Voltage: CTL[V] 0 5 2 3 4 CTL Supply Voltage: CTL[V] 5 Figure 38. CTL ON / OFF Mode Voltage (Tj = 125 C) Figure 37. CTL ON / OFF Mode Voltage (Tj = 25 C) www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 1 18/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series Typical Performance Curves BD450M2WEFJ-C / BD450M2WFP3-C Reference Data Unless otherwise specified: -40 C Tj +150 C, VCC = 13.5 V, IOUT = 0 mA 30 Tj = -40 C 25 4 CTL Bias Current: ICTL[A] Shutdown Current: Ishut[A] 5 3 2 1 Tj = 25 C 20 Tj = 125 C 15 10 5 0 -40 0 40 80 120 Junction Temperature: Tj[C] 160 0 1 2 3 4 CTL Supply Voltage: CTL[V] 5 Figure 40. CTL Bias Current vs. CTL Supply Voltage Figure 39. Shut Down Current vs. Temperature (CTL = 0 V) www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 0 19/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series Measurement Circuit for Typical Performance Curves (BD433 / 450M2WEFJ-C) 8:VCC 4.7F 7:CTL 6:N.C. 5:GND BD4xxM2WEFJ-C 1:VOUT 2:N.C. 3:N.C. 4:N.C. 10F Measurement Setup for Figure 5, 7, 16, 17, 21, Figure 23, 25, 34, 35, 39 4.7F 10F 8:VCC 4.7F 7:CTL 6:N.C. 7:CTL 6:N.C. 7:CTL 6:N.C. 5:GND BD4xxM2WEFJ-C 1:VOUT 2:N.C. 3:N.C. 4:N.C. IOUT Measurement Setup for Figure 9, 27 5:GND BD4xxM2WEFJ-C 1:VOUT Measurement Setup for Figure 10, 28 4.7F 10F Measurement Setup for Figure 6, 8, 14, 15, Figure 24, 26, 32, 33 8:VCC 8:VCC 2:N.C. 3:N.C. 4:N.C. IOUT Measurement Setup for Figure 11, 29 Measurement Setup for Figure 12, 30 Measurement Setup for Figure 18, 19, 20, Figure 36, 37, 38 Measurement Setup for Figure 22, 40 5:GND BD4xxM2WEFJ-C 1:VOUT 10F 2:N.C. 3:N.C. 4:N.C. IOUT Measurement Setup for Figure 13, 31 www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 20/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series Measurement Circuit for Typical Performance Curves (BD433 / 450M2EFJ-C) Measurement Setup for Figure 5, 7, 16, Figure 23, 25, 34 8:VCC 7:N.C. 6:N.C. Measurement Setup for Figure 6, 8, 14, 15, Figure 24, 26, 32, 33 Measurement Setup for Figure 9, 27 8:VCC 5:GND 7:N.C. 6:N.C. 5:GND 1Vrms 4.7F 4.7F BD4xxM2EFJ-C BD4xxM2EFJ-C 1:VOUT 2:N.C. 3:N.C. 1:VOUT 4:N.C. 10F 10F Measurement Setup for Figure 10, 28 8:VCC 7:N.C. 6:N.C. Measurement Setup for Figure 11, 29 2:N.C. 3:N.C. 4:N.C. IOUT Measurement Setup for Figure 12, 30 5:GND 4.7F BD4xxM2EFJ-C 1:VOUT 10F 2:N.C. 3:N.C. 4:N.C. IOUT Measurement Setup for Figure 13, 31 www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 21/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series Measurement Circuit for Typical Performance Curves (BD433 / 450M2WFP3-C) 4:GND 4:GND BD4xxM2WFP3-C BD4xxM2WFP3-C 1:VCC 2:CTL 4.7F Measurement Setup for Figure 5, 7, 16, 17, 21, Figure 23, 25, 34, 35, 39 Measurement Setup for Figure 6, 8, 14, 15, Figure 24, 26, 32, 33 4:GND BD4xxM2WFP3-C BD4xxM2WFP3-C 2:CTL 3:VOUT 4.7uF 10uF 1:VCC 2:CTL 4.7F 10F Measurement Setup for Figure 11, 29 4:GND 4:GND BD4xxM2WFP3-C 2:CTL 1:VCC 10F IOUT Measurement Setup for Figure 9, 27 2:CTL IOUT Measurement Setup for Figure 12, 30 4:GND BD4xxM2WFP3-C 3:VOUT 3:VOUT 3:VOUT Measurement Setup for Figure 10, 28 1:VCC 2:CTL 4.7F 10F 4:GND 1:VCC 1:VCC 3:VOUT 3:VOUT BD4xxM2WFP3-C 1:VCC 2:CTL 3:VOUT 4.7F IOUT Measurement Setup for Figure 13, 31 www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 4.7F 10F Measurement Setup for Figure 18, 19, 20, Figure 36, 37, 38 22/34 4.7F 10F Measurement Setup for Figure 22, 40 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series Measurement Circuit for Typical Performance Curves (BD433 / 450M2FP3-C) 4:GND 4:GND BD4xxM2FP3-C BD4xxM2FP3-C 1:VCC 4.7uF 2:GND 3:VOUT 1:VCC 10uF Measurement Setup for Figure 5, 7, 16, Figure 23, 25, 34 2:GND 3:VOUT 4.7uF Measurement Setup for Figure 6, 8, 14, 15, Figure 24, 26, 32, 33 10uF IOUT Measurement Setup for Figure 9, 27 4:GND BD4xxM2FP3-C 1:VCC 2:GND 3:VOUT 1Vrms 4.7uF Measurement Setup for Figure 10, 28 Measurement Setup for Figure 11, 29 10uF IOUT Measurement Setup for Figure 12, 30 Measurement Setup for Figure 13, 31 www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 23/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series Selection of Components Externally Connected VCC Pin Insert Capacitors with a capacitance of 0.1 F or higher between the VCC and GND pin. Choose the capacitance according to the line between the power smoothing circuit and the VCC pin. Selection of the capacitance also depends on the application. Verify the application and allow sufficient margins in the design. We recommend using a capacitor with excellent voltage and temperature characteristics. Output Pin Capacitor In order to prevent oscillation, a capacitor needs to be placed between the output pin and GND pin. We recommend using a capacitor with a capacitance of 10 F (Typ.) or higher. Electrolytic, tantalum and ceramic capacitors can be used. When selecting the capacitor ensure that the capacitance of 6 F or higher is maintained at the intended applied voltage and temperature range. Due to changes in temperature the capacitor's capacitance can fluctuate possibly resulting in oscillation. For selection of the capacitor refer to the data of Figure 41. The stable operation range given in the data of Figure 41 is based on the standalone IC and resistive load. For actual applications the stable operating range is influenced by the PCB impedance, input supply impedance and load impedance. Therefore verification of the final operating environment is needed. When selecting a ceramic type capacitor, we recommend using X5R, X7R or better with excellent temperature and DC-biasing characteristics and high voltage tolerance. Also, in case of rapidly changing input voltage and load current, select the capacitance in accordance with verifying that the actual application meets with the required specification. Condition VCC = 13.5 V (CTL = 5 V) CIN = 0.1 F 10 F COUT (Typ.) -40 C Tj +150 C unstable operation range Condition VCC = 13.5 V (CTL = 5 V) CIN = 0.1 F -40 C Tj +150 C stable operation range stable operation range unstable operation range Figure 41. ESR vs. IOUT Figure 42. COUT vs. IOUT Measurement Setup 8:VCC CIN 7:CTL 6:N.C. 8:VCC 5:GND CIN BD4xxM2WEFJ-C 7:N.C. 6:N.C. 5:GND 4:GND BD4xxM2EFJ-C 1:VCC 1:VOUT ESR 2:N.C. 3:N.C. 1:VOUT 4:N.C. ESR IOUT COUT 2:N.C. 3:N.C. 4:GND BD4xxM2WFP3-C 2:CTL BD4xxM2FP3-C 3:VOUT 1:VCC 2:GND 3:VOUT 4:N.C. CIN ESR CIN IOUT IOUT COUT COUT ESR COUT IOUT Figure 43. Measurement Setups for ESR Reference Data (about Output Pin Capacitor) www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 24/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series Power Dissipation HTSOP-J8 5 IC mounted on ROHM standard board based on JEDEC. Board material: FR4 Board size: 114.3 mm x 76.2 mm x 1.6 mmt (with thermal via on the board) Mount condition: PCB and exposed pad are soldered. Top copper foil: The footprint ROHM recommend. + wiring to measure. Power Dissipation: Pd[W] 4 2.9 W 3 : 1-layer PCB (Copper foil area on the reverse side of PCB: 0 mm x 0 mm) : 4-layer PCB (2 inner layers and Copper foil area on the reverse side of PCB: 74.2 mm x 74.2 mm) 2 0.75 W 1 0 0 25 50 75 100 125 150 Condition: ja = 166.7 C/W, jc (top) = 45 C/W Condition: ja = 43.1 C/W, jc (top) = 16 C/W, jc (bottom) = 10 C/W Ambient Temperature: Ta[] Figure 44. Package Data (HTSOP-J8) SOT223-4(F) 5 IC mounted on ROHM standard board based on JEDEC. Board material: FR4 Board size: 114.3 mm x 76.2 mm x 1.6 mmt (with thermal via on the board) Mount condition: PCB and exposed pad are soldered. Top copper foil: The footprint ROHM recommend. + wiring to measure. Power Dissipation: Pd[W] 4 3 2 1.5 W 1 0.6 W 0 0 25 50 75 100 125 : 1-layer PCB (Copper foil area on the reverse side of PCB: 0 mm x 0 mm) : 4-layer PCB (2 inner layers and Copper foil area on the reverse side of PCB: 74.2 mm x 74.2 mm) Condition: ja = 208.3 C/W, jc (top) = 52 C/W Condition: ja = 83.3 C/W, jc (top) = 36 C/W, jc (bottom) = 17 C/W 150 Ambient Temperature: Ta[C] Figure 45. Package Data (SOT223-4(F)) www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 25/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series Refer to the heat mitigation characteristics illustrated in Figure 44, 45 when using the IC in an environment of Ta 25 C. The characteristics of the IC are greatly influenced by the operating temperature, and it is necessary to operate under the maximum junction temperature Tjmax. Even if the ambient temperature Ta is at 25 C it is possible that the junction temperature Tj reaches high temperatures. Therefore, the IC should be operated within the power dissipation range. The following method is used to calculate the power consumption Pc (W) Pc = ( VCC - VOUT ) x IOUT + VCC x Icc Power dissipation Pd Pc The load current IOUT is obtained by operating the IC within the power dissipation range. IOUT Pd - VCC x Icc VCC - VOUT VCC VOUT IOUT Icc Pc : Input Voltage : Output Voltage : Load Current : Circuit Current : Power Consumption (Refer to Figure 13, 31 for the Icc.) Thus, the maximum load current IOUTmax for the applied voltage VCC can be calculated during the thermal design process. The following method is also used to calculate the junction temperature Tj. Ta Tc Tj jc Tj = Pc x jc + Tc : Ambient Temperature : Case Temperature : Junction Temperature : Thermal Resistance (Junction to Case) HTSOP-J8 Calculation Example 1) with Ta = 105 C VCC = 13.5 V, VOUT = 5.0 V IOUT 1.06 W - 13.5 V x Icc 8.5 V IOUT 125 mA ( Icc: 45 A ) IC stand alone ja = 43.1 C/W -23 mW/C 25 C = 2.9 W 105 C = 1.06 W At Ta = 105 C with Figure 44 condition, the calculation shows that 125 mA of output current is possible at 8.5 V potential difference across input and output. The thermal calculation shown above should be taken into consideration during the thermal design in order to keep the whole operating temperature range within the power dissipation range. In the event of shorting (i.e. VOUT and GND pins are shorted) the power consumption Pc of the IC can be calculated as follows: Pc = VCC x ( Icc + Ishort ) ( Refer to Figure 10, 28 for the Ishort ) Ishort : Short Current Calculation Example 2) with Tc(bottom) = 80 C, VCC = 13.5 V, VOUT = 5.0 V, IOUT = 80 mA At Tc(bottom) = 80 C with Figure 44 condition, the power consumption Pc of the IC can be calculated as follows: Pc = ( VCC - VOUT ) x IOUT + VCC x Icc Pc = ( 13.5 V - 5.0 V ) x 80 mA + 13.5 V x Icc Pc = 0.681 W ( Icc = 45 A ) At the power consumption Pc is 0.681 W, the junction temperature Tj can be calculated as follows: Tj = Pc x jc + Tc Tj = 0.681 W x jc + 80 C Tj = 86.8 C ( jc (bottom) = 10 C/W ) The junction temperature is 86.8 C, at above condition. The thermal calculation shown above should be taken into consideration during the thermal design in order to keep the whole operating temperature range within Tj 150 C. www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 26/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series SOT223-4(F) Calculation Example 1) with Ta = 105 C VCC = 13.5 V, VOUT = 5.0 V IOUT 0.54 W - 13.5 V x Icc IOUT 63 mA 8.5 V ( Icc: 45 A ) IC stand alone ja = 83.3 C/W -12 mW/C 25 C = 1.50 W 105 C = 0.54 W At Ta = 105C with Figure 45 condition, the calculation shows that 63 mA of output current is possible at 8.5 V potential difference across input and output. The thermal calculation shown above should be taken into consideration during the thermal design in order to keep the whole operating temperature range within the power dissipation range. In the event of shorting (i.e. VOUT and GND pins are shorted) the power consumption Pc of the IC can be calculated as follows: Pc = VCC x ( Icc + Ishort ) ( Refer to Figure 10, 28 for the Ishort ) Calculation Example 2) with Tc(bottom) = 92 C, VCC = 13.5 V, VOUT = 5.0 V, IOUT = 80 mA At Tc(bottom) = 92 C with Figure 45 condition, the power consumption Pc of the IC can be calculated as follows: Pc = ( VCC - VOUT ) x IOUT + VCC x Icc Pc = ( 13.5 V - 5.0 V ) x 80 mA + 13.5 V x Icc Pc = 0.681 W ( Icc = 45 A ) At the power consumption Pc is 0.681 W, the junction temperature Tj can be calculated as follows: Tj = Pc x jc + Tc Tj = 0.681 W x jc + 92 C Tj = 103.6 C ( jc (bottom) = 17 C/W ) The junction temperature is 103.6 C, at above condition. The thermal calculation shown above should be taken into consideration during the thermal design in order to keep the whole operating temperature range within Tj 150 C. www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 27/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series Application Examples Applying positive surge to the VCC pin If the possibility exists that surges higher than 45 V will be applied to the VCC pin, a Zener Diode should be placed between the VCC pin and GND pin as shown in the figure below. 4:GND 4:GND BD4xxM2WFP3-C BD4xxM2FP3-C 1:VCC 2:CTL 3:VOUT Battery Zener Diode 1:VCC VOUT CIN COUT Input switch HTSOP-J8 2:GND 3:VOUT Battery Zener Diode VOUT COUT CIN SOT223-4(F) Figure 46. Sample Application Circuit 1 Applying negative surge to the VCC pin If the possibility exists that negative surges lower than the GND are applied to the VCC pin, a Shottky Diode should be place between the VCC pin and GND pin as shown in the figure below. 4:GND 4:GND BD4xxM2WFP3-C BD4xxM2FP3-C 1:VCC 2:CTL Battery Shottky Diode 1:VCC 3:VOUT VOUT CIN Input switch HTSOP-J8 COUT 2:GND 3:VOUT Battery Shottky Diode VOUT CIN COUT SOT223-4(F) Figure 47. Sample Application Circuit 2 Implementing a Protection Diode If the possibility exists that a large inductive load is connected to the output pin resulting in back-EMF at time of startup and shutdown, a protection diode should be placed as shown in the figure below. VOUT Figure 48. Sample Application Circuit 3 I / O Equivalence Circuit VCC (Applicable for product with Enable Input) 4 M (Typ.) VOUT 1545 k (Typ./5.0 V Output) 840 k (Typ./3.3 V Output) 530 k (Typ.) Figure 49. Input / Output Equivalence Circuit www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 28/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series Operational Notes 1) Absolute Maximum Ratings Exceeding the absolute maximum rating for supply voltage, operating temperature or other parameters can result in damages to or destruction of the chip. In this event it also becomes impossible to determine the cause of the damage (e.g. short circuit, open circuit, etc.). Therefore, if any special mode is being considered with values expected to exceed the absolute maximum ratings, implementing physical safety measures, such as adding fuses, should be considered. 2) The electrical characteristics given in this specification may be influenced by conditions such as temperature, supply voltage and external components. Transient characteristics should be sufficiently verified. 3) GND Electric Potential Keep the GND pin potential at the lowest (minimum) level under any operating condition. Furthermore, ensure that, including the transient, none of the pin's voltages are less than the GND pin voltage. 4) GND Wiring Pattern When both a small-signal GND and a high current GND are present, single-point grounding (at the set standard point) is recommended. This in order to separate the small-signal and high current patterns and to ensure that voltage changes stemming from the wiring resistance and high current do not cause any voltage change in the small-signal GND. Similarly, care must be taken to avoid wiring pattern fluctuations in any connected external component GND. 5) Inter-Pin Shorting and Mounting Errors Ensure that when mounting the IC on the PCB the direction and position are correct. Incorrect mounting may result in damaging the IC. Also, shorts caused by dust entering between the output, input and GND pin may result in damaging the IC. 6) Inspection Using the Set Board The IC needs to be discharged after each inspection process as, while using the set board for inspection, connecting a capacitor to a low-impedance pin may cause stress to the IC. As a protection from static electricity, ensure that the assembly setup is grounded and take sufficient caution with transportation and storage. Also, make sure to turn off the power supply when connecting and disconnecting the inspection equipment. 7) Power Dissipation (Pd) Should by any chance the power dissipation rating be exceeded the rise in temperature of the chip may result in deterioration of the properties of the chip. The absolute maximum rating of the Pd stated in this specification is when the IC is mounted on a 114.3mm x 76.2mm x 1.6mmt glass epoxy board. In case of exceeding this absolute maximum rating, increase the board size and copper area to prevent exceeding the Pd rating. 8) Thermal Design The power dissipation under actual operating conditions should be taken into consideration and a sufficient margin should be allowed for in the thermal design. On the reverse side of the package this product has an exposed heat pad for improving the heat dissipation. Use both the front and reverse side of the PCB to increase the heat dissipation pattern as far as possible. The amount of heat generated depends on the voltage difference across the input and output, load current, and bias current. Therefore, when actually using the chip, ensure that the generated heat does not exceed the Pd rating. Tjmax: maximum junction temperature = 150C, Ta: Ambient Temperature (C), ja: Junction-to-Ambient Thermal Resistance (C/W), Pd: Power Dissipation Rating (W), Pc: Power Consumption (W), VCC: Supply Voltage, VOUT: Output Voltage, IOUT: Output Current, Icc: Circuit Current Power Dissipation Rating Power Consumption Pd (W) = ( Tjmax - Ta ) / ja Pc (W) = ( VCC - VOUT ) x IOUT + VCC x Icc 9) Overcurrent Protection Circuit This IC incorporates an integrated overcurrent protection circuit that is activated when the load is shorted. This protection circuit is effective in preventing damage due to sudden and unexpected incidents. However, the IC should not be used in applications characterized by continuous operation or transitioning of the protection circuit. 10) Thermal Shut Down (TSD) This IC incorporates and integrated thermal shutdown circuit to prevent heat damage to the IC. Normal operation should be within the power dissipation rating, if however the rating is exceeded for a continued period, the junction temperature (Tj) will rise and the TSD circuit will be activated and turn all output pins OFF. After the Tj falls below the TSD threshold the circuits are automatically restored to normal operation. Note that the TSD circuit operates in a situation that exceeds the absolute maximum ratings and therefore, under no circumstances, should the TSD circuit be used in a set design or for any purpose other than protecting the IC from heat damage. www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 29/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series 11) In some applications, the VCC and pin potential might be reversed, possibly resulting in circuit internal damage or damage to the elements. For example, while the external capacitor is charged, the VCC shorts to the GND. Use a capacitor with a capacitance with less than 1000 F. We also recommend using reverse polarity diodes in series or a bypass between all pins and the VCC pin. Bypass Diode Reverse Polarity Diode VCC VOUT GND Figure 50. 12) This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them isolated. P/N junctions are formed at the intersection of these P layers with the N layers of other elements to create a variety of parasitic elements. For example, in case a resistor and a transistor are connected to the pins as shown in the figure below then: The P/N junction functions as a parasitic diode when GND > pin A for the resistor, or GND > pin B for the transistor. Also, when GND > pin B for the transistor (NPN), the parasitic diode described above combines with the N layer of the other adjacent elements to operate as a parasitic NPN transistor. Parasitic diodes inevitably occur in the structure of the IC. Their operation can result in mutual interference between circuits and can cause malfunctions and, in turn, physical damage to or destruction of the chip. Therefore do not employ any method in which parasitic diodes can operate such as applying a voltage to an input pin that is lower than the (P substrate) GND. Figure 51. www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 30/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series Physical Dimension, Tape and Reel Information (HTSOP-J8) Package Name HTSOP-J8 <Tape and Reel information> Tape Embossed carrier tape Quantity 2500pcs Direction of feed E2 The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand Direction of feed 1pin Reel www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 ) Order quantity needs to be multiple of the minimum quantity. 31/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series Physical Dimension, Tape and Reel Information (SOT223-4(F)) Package Name www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 SOT223-4(F) 32/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series Marking Diagrams (Top View) SOT223-4(F) (Top View) HTSOP-J8 (Top View) Part Number Marking Part Number Marking LOT Number LOT Number 1PIN Mark 1PIN Part Number Marking Output Voltage [V] Enable *1 Input Part Number Marking Output Voltage [V] Enable Input *1 433M2W 450M2W 433M2 450M2 3.3 5.0 3.3 5.0 433M2W 450M2W 433M2 450M2 3.3 5.0 3.3 5.0 *1 : Includes Enable Input *1 : Includes Enable Input : Not includes Enable Input www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 : Not includes Enable Input 33/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 BD4xxM2-C Datasheet Series Revision History Date Revision Changes 05.Dec.2012 001 New Release (BD450M2WEFJ-C, BD450M2EFJ-C) 15.Jan.2013 002 Additional Entry (BD4xxM2-C Series) P.1 , P.3 Figure 3, P.4, P.5 Figure 4, P.9, P.13, P23, P.24, P.26, P.29, P.30 Improve the explanation and corrected type. 29.Oct.2013 003 30.Sept.2016 004 P.28, P.30 Improve the correct figure number because of sequence. Before) Figure 48, 49, 50, 51, 52, 53. After) Figure 46, 47, 48, 49, 50, 51. AEC-Q100 Grade postscript Improve the description ,SOT223-4F to SOT223-4(F) www.rohm.com (c) 2013 ROHM Co., Ltd. All rights reserved. TSZ2211115001 34/34 TSZ02201-0G1G0AN0063-1-2 30.Sept.2016 Rev.004 Notice Precaution on using ROHM Products 1. (Note 1) If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment , aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property ("Specific Applications"), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM's Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASS CLASSb CLASS CLASS CLASS CLASS 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM's Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in the range that does not exceed the maximum junction temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice-PAA-E (c) 2015 ROHM Co., Ltd. All rights reserved. Rev.003 Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label A two-dimensional barcode printed on ROHM Products label is for ROHM's internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign trade act, please consult with ROHM in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. 2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the Products with other articles such as components, circuits, systems or external equipment (including software). 3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to manufacture or sell products containing the Products, subject to the terms and conditions herein. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice-PAA-E (c) 2015 ROHM Co., Ltd. All rights reserved. Rev.003 Datasheet General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny ROHM's Products against warning, caution or note contained in this document. 2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM's Products, please confirm the la test information with a ROHM sale s representative. 3. The information contained in this doc ument is provi ded on an "as is" basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. Notice - WE (c) 2015 ROHM Co., Ltd. All rights reserved. Rev.001 Datasheet bd450m2wefj-c - Web Page Buy Distribution Inventory Part Number Package Unit Quantity Minimum Package Quantity Packing Type Constitution Materials List RoHS bd450m2wefj-c HTSOP-J8 2500 2500 Taping inquiry Yes