G.1
Accessories
G
Accessories
Accessories
Shield connection terminals KLBÜ G.2
Multi-pole terminal strips for direct mounting G.12
Busbars G.18
Terminal rails G.24
Terminal markers G.34
Printing systems G.52
Tools G.60
Wire end ferrules G.82
Insulated cable connectors G.94
Contents
G.2
Accessories
G
Overview shield connection terminals KLBÜ
The theoretical concept
Part 1 of the VDE 0133 standard specifies the required equipo-
tential bonding for the electrical components of a machine. The
aim is to prevent any undesirable consequences occurring as
a result of electrostatic, electromagnetic and net-work bound
interference.
The following measures serve this purpose:
• Usingfiltersandtimedelaydevices.
• Dividingearth(PE)into“dirty”and“clean”.
• Neutralgroundingusinglargeearthcablesforbonding.
• Keepingallbondingleadsasshortaspossible.
• Routingallconnectionsparalleltothebondingsurface.
• Separationandshieldingofswitchingdevicesandinterference
sensitive equipment, shielded at one end only.
• Shieldedlinesareusedforallmotorandallsignalconnection.
These shielded cables for signals are grounded at one end.
Drives to Motors should be grounded at both ends.
• Themasscurrentisneutralgrounded
Control signals
Digital Analogue Position signals
CNC – GND CNC – GND
Control
To further
servo-amplifiers
Resolver
Power
supply
unit
Mains
filter
Mains
filter
3
+25 V
XGND
BRAKE
PE
U2
V2
W2
L1
L2
L3
+DC
–DC
X1
X6
X2
X5
Booster
PCRESOLVER
Personal-
Computer
SW +
SW -
AGND
PSTOP
NSTOP
DGND
I/O
ENABLE
BTB
BTB
SHIELD
WPE
WPE
KLBÜ
KLBÜ
KLBÜ
KLBÜ
KLBÜ
Overview of KLBÜ fittings available
For busbars For direct mounting For C-profiles For TS 35 Clip-on for
10 x 3 insulating/conducting 10 x 3 busbar
G.3
Accessories
G
Overview shield connection terminals KLBÜ
In detail
Compression spring
• Toensurebothsimplehandlingand
proper connection with permanent
contact pressure as a result of the
spring effect
Reliable contact
• Changesindiameter(flow)ofthe
conductor compensated for by the
elastic behaviour of the clamping yoke
for flexible adjustment to the cable
diameter
No extra tools necessary
• Simplyswivel onto the busbar by
hand – retrospectively if necessary
Full range
• Forconductorsfrom2to37mm
diameter
Many options available
• Weidmülleroffersawiderangeof
different fastenings for mounting
shield connection terminals
G.4
Accessories
G
a
c
b
Shield connection terminals KLBÜ for 10 x 3 mm busbars
Clamping yoke
Cable fastened against
the busbar from below
KLBÜ 2 x 2-6 KLBÜ 3-8 KLBÜ 4-13.5 KLBÜ 10-20 KLBÜ 15-32
KLBÜ
Marking on the product: T
MarkingEN50019: T Ex e II
MarkingEX-RL94/9/EC: II2GD
ECtypetestingcertificate: DMT02ATEXE024U
Ordering data
Type For cable diameter Dimensions (a x b x c) mm Qty. Order No.
KLBÜ 2 x 2-6 2.0 ... 6.0 mm 15.0 x 18.0 x 24.0 10 1675350000
KLBÜ 3-8 3.0 ... 8.0 mm 13.0 x 18.0 x 26.0 10 1600480000
KLBÜ 4 x 13.5 4.0 ... 13.5 mm 20.0 x 20.5 x 31.5 10 1592810000
KLBÜ 10-20 10.0 ... 20.0 mm 25.0 x 26.0 x 40.0 10 1600490000
KLBÜ 15-32 15.0 ... 32.0 mm 36.0 x 32.0 x 63.9 10 1716300000
10 x 3 mm busbars Length Material Qty. Order No.
SSch 10 x 3 x 1000 Cu, Sn, Pb 1000.0 mm Cu, Sn, Pb 1 0348900000
SSch 10 x 3 x 1000 Fe, Zn, 8B 1000.0 mm Fe, Zn, 8B 1 1746130000
1 3
! !
2 4
T
✓
✓
✗
✓b + 4 mm
G.5
Accessories
G
b
ac
d
Shield connection terminals KLBÜ for 10 x 3 mm busbars
Clamping yoke
Cable fastened onto the
busbar from above
KLBÜ CO 1 KLBÜ CO 2 KLBÜ CO 3 KLBÜ CO 4 KLBÜ CO 5
KLBÜ CO
Marking on the product: T
MarkingEN50019: T Ex e II
MarkingEX-RL94/9/EC: II2GD
ECtypetestingcertificate: DMT02ATEXE024U
Ordering data
Type For cable diameter Dimensions (a x b x c x d) mm Qty. Order No.
KLBÜ CO 1 3.0 ... 10.0 mm 18.0 x 12.0 x 13.2 x 32.0 10 1753311001
KLBÜ CO 2 4.0 ... 15.0 mm 18.0 x 20.0 x 21.1 x 41.6 10 1752131001
KLBÜ CO 3 10.0 ... 20.0 mm 25.0 x 23.0 x 24.0 x 45.0 10 1749151001
KLBÜ CO 4 15.0 ... 28.0 mm 25.0 x 31.0 x 32.0 x 56.0 10 1749161001
KLBÜ CO 5 20.0...37.0mm 32.0x40.0x42.7x64.5 10 1755081001
10 x 3 mm busbars Length Material Qty. Order No.
SSch 10 x 3 x 1000 Cu, Sn, Pb 1000.0 mm Cu, Sn, Pb 1 0348900000
SSch 10 x 3 x 1000 Fe, Zn, 8B 1000.0 mm Fe, Zn, 8B 1 1746130000
1 3
! !
2
T
✓
✓
✗
✓a + 4 mm
G.6
Accessories
G
Shield connection terminals KLBÜ for 10 x 3 mm busbars
Busbar holders
Insulated mounting on TS 35
WSH
ECtypetestingcertificate: DMT02ATEXE024U
Ordering data
Type Width Qty. Order No.
WSH 1 8.0 mm 10 1068700000
WSH3/H/N 8.0 mm 10 1715970000
WSH 5 8.0 mm 10 1080100000
WSH 6 8.0 mm 10 1080200000
10 x 3 mm busbars Length Material Qty. Order No.
SSch 10 x 3 x 1000 Cu, Sn, Pb 1000.0 mm Cu, Sn, Pb 1 0348900000
Type WSH 1 Type WSH 3/H/N
Type WSH 5 Type WSH 6
Horizontal mounting only
G.7
Accessories
G
Shield connection terminals KLBÜ for 10 x 3 mm busbars
Busbar holders
Conductive mounting on TS 35
WSH
ECtypetestingcertificate: DMT02ATEXE024U
Ordering data
TS 35-Clip Dimensions (L x B x H) mm Qty. Order No.
BS 35/WSH 2 52.0x37.0x13.0 10 1760720000
Busbar connector Dimensions (L x B x H) mm Qty. Order No.
BFEH 1/WSH 20.0 x 31.0 x 13.5 10 1082400000
Angled rail Dimensions (L x B x H) mm Qty. Order No.
SMSEWSHU1MT 134.0 x 13.0 x 134.0 10 1083900000
Busbar holder sets Contents(partslooseinplasticbag)
BS 35/WSH 2 BFEH 1/WSH SMSEWSHU1MT Qty. Order No.
WSH 18 MT 1 ea. 2 ea. 2 ea. 10 1083100000
WSH 19 MT 1 ea. 1 ea. 1 ea. 10 1083200000
WSH 20 MT 1 ea. 1 ea. 1ea.(straight) 10 1752950000
10 x 3 mm busbars Length Material Qty. Order No.
SSch 10 x 3 x 1000 Cu, Sn, Pb 1000.0 mm Cu, Sn, Pb 1 0348900000
SSch 10 x 3 x 1000 Fe, Zn, 8B 1000.0 mm Fe, Zn, 8B 1 1746130000
TS 35-Clip
BS 35/WSH 2
Busbar connector
BFEH 1/WSH
Angled rail
SMSEWSHU1MT
Installation example 1
• Onebusbar
• 2xWSH19MT
busbar holder set
Installation example 2
• Twobusbars
• 2xWSH18MT
busbar holder set
G.8
Accessories
G
Shield connection terminals KLBÜ – Mounting directly on metal plate
b
ac
d
e
Clamping yoke
KLBÜ 3-8 SC KLBÜ 4-13.5 SC KLBÜ 10-20 SC KLBÜ 15-32 SC
KLBÜ SC
Marking on the product: T
MarkingEN50019: T Ex e II
MarkingEX-RL94/9/EC: II2GD
ECtypetestingcertificate: DMT02ATEXE024U
Ordering data
Type For cable diameter Thread length
Dimensions (a x b x c) mm
Qty. Order No.
KLBÜ 3-8 SC 3.0 ... 8.0 mm 5.65 mm 13.5 x 11.5 x 18.0 x 26.0 10 1692261001
KLBÜ 4-13.5 SC 4.0 ... 13.5 mm 5.30 mm 20.0x17.8x20.3x31.4 10 1712311001
KLBÜ 10-20 SC 10.0 ... 20.0 mm 5.30 mm 24.8 x 23.0 x 26.0 x 40.0 10 1712321001
KLBÜ 15-32 SC 15.0 ... 32.0 mm 4.80 mm 36.0 x 33.3 x 32.0 x 64.0 10 1718341001
Operating tool Qty. Order No.
BTWZ KLBÜ 1 1742630000
ø 4.2 mm
10 mm
Drilling template KLBÜ 15-32 SC
M4
1 3
!
2
✓
✓
!a > b = ✓
a < b = ✗
a
b
!✓
✗Tc + 4 mm
G.9
Accessories
G
Shield connection terminals KLBÜ – Mounting directly on metal plate
Busbar holder / Spacer
WSH 4 MT / SP
ECtypetestingcertificate: DMT02ATEXE024U
Ordering data
Busbar holder Qty. Order No.
WSH 4 MT 10 1079900000
Type Length Qty. Order No.
SP 15, set of 2 15 mm 1 3896100000
SP 20, set of 2 20 mm 1 3896200000
SP 30, set of 2 30 mm 1 3896300000
Busbar holder
Spacer
Set(WSH4MT)consistingof:
– 1 busbar holder
–1busbarconnector(BFEH1/WSH)
M6 outer and inner thread
(15mm,20mmand30mmlong)
12
28
40.5
ø Du for M 5
ø = 5.2 mm
Mounting plate
70
10 x 3
G.10
Accessories
G
Shield connection terminals KLBÜ – Mounting on TS 35
FM 4 / BS 35 II
Marking on the product: T
MarkingEN50019: T Ex e II
MarkingEX-RL94/9/EC: II2GD
ECtypetestingcertificate: DMT02ATEXE024U
Ordering data
FM 4 foot Qty. Order No.
FM 4 40 0687900000
Clamping yoke holder For cable diameter Qty. Order No.
BS 35 II without KLBÜ 10 1723800000
BS 35 II / KLBÜ 3-8 3.0 ... 8.0 mm 10 1723810000
BS 35 II / KLBÜ 4-13.5 4.0 ... 13.5 mm 10 1723820000
BS 35 II / KLBÜ 3-8/2 x 2-6 3.0 ... 8.0 mm / 2.0 ... 6.0 mm 10 1749430000
BS 35 II / KLBÜ 2 x 3-8/2 x 2-6 3.0 ... 8.0 mm / 2.0 ...6.0 mm 10 1768020000
FM 4 foot / Clamping yoke holder
FM 4 foot
Clamping yoke holder
BS 35 II
(without KLBÜ)
BS 35 II / KLBÜ 3-8 BS 35 II / KLBÜ 3-8 / 2 x 2-6
The KLBÜ SC clamping yokes
(seepageG.8)
are screwed onto the FM 4 foot.
G.11
Accessories
G
Shield connection terminals KLBÜ for TS27
b
ac
d
e
Clamping yoke
KLBÜ 3-8 CPF KLBÜ 4-13.5 CPF KLBÜ 10-20 CPF KLBÜ 15-32 CPF
KLBÜ CPF
Marking on the product: T
MarkingEN50019: T Ex e II
MarkingEX-RL94/9/EC: II2GD
ECtypetestingcertificate: DMT02ATEXE024U
Ordering data
Type For cable diameter Dimensions (a x b x c x d) mm Qty. Order No.
KLBÜ 3-8 CPF 3.0 ... 8.0 mm 13.5 x 11.5 x 18.0 x 26.0 10 1752681001
KLBÜ 4-13.5 CPF 4.0 ... 13.5 mm 20.0x17.8x20.3x31.4 10 1752691001
KLBÜ 10-20 CPF 10.0 ... 20.0 mm 24.8 x 23.0 x 26.0 x 40.0 10 1752701001
KLBÜ 15-32 CPF 15.0 ... 32.0 mm 36.0 x 33.3 x 32.0 x 64.0 10 1752711001
C-rail Qty. Order No.
TS27x12.5M/ST/F.ZN 10 m 1802690000
G
G.12
Screw connection
Technical data
Rated data
Rated voltage V
Rated current A
Rated cross-section mm²
Rated impulse voltage / Pollution severity kV/-
Gauge to IEC 60947-1 / UL94 Flammability class
Approvals
Clamped conductors (H05V/H07V)
solid / stranded mm²
flexible / Stranded wire with end ferrules mm²
Tightening torque range (clamping screw)
Stripping length / Blade size mm/-
Note
Width/Height/ø mounting hole mm
Length / mounting dimensions
Max. clamping range mm²
Version
2-pole
3-pole
4-pole
5-pole
6-pole
7-pole
8-pole
9-pole
10-pole
12-pole
14-pole
16-pole
Note
For detailed information on other accessories and ap-
plications, refer to the „Accessories“ section
Solder strip
Marking strips, printed
Printed
Marking strips, unprinted
Unprinted
MK 2/12 2.5 mm²
15 x 15 / 3.2
Refer to order data
0.2...4
Type
Length/Mounting dimensions
Qty Order No.
MK 2/12 86 mm 80.0 mm 50 0241260000
Type Width Qty Order No.
MF 2/12 1X2.8/1.6 75 mm 100 0241760000
BSTB 28/12/6,35 U 1-12 50 0245700000
BSTB 28/12/6,35 O 1-12 50 0278500000
BSTO 28/12/6,35 50 0245600000
Ordering data
(see assortment in catalogue 7)
IEC UL CSA
125 300 300
24 10 10
2.5 AWG 24...12 AWG 24...12
3 / 3
A2 / 5VA
r # a
Rated connection
0.5...4 / 1.5...2.5
0.5...2.5 / 0.5...1.5
0.4 NmM 2.5
5 / 0.6 x 3.5 mm
Accessories
IEC 60947-7-1
MK 3/2...12 2.5 mm²
15 x 16.1 / 3.45
Refer to order data
0.33...4
IEC UL CSA
400 300 300
24 25 25
2.5 AWG 22...12 AWG 22...12
6 / 3
A2 / 5VA
r # i a
Rated connection
0.5...4 / 1.5...2.5
0.5...2.5 / 0.5...1.5
0.4...0.45 Nm (M 2.5)
5 / 0.6 x 3.5 mm
IEC 60947-7-1
Type
Length/Mounting dimensions
Qty Order No.
MK 3/2 17.4 mm 18.5 mm 100 0273820000
MK 3/3 26.5 mm 18.5 mm 50 0273920000
MK 3/4 35.75 mm 18.5 mm 50 0274020000
MK 3/5 45 mm 18.5 mm 50 0274120000
MK 3/6 54.25 mm 37.0 mm 50 0274220000
MK 3/7 63.5 mm 37.0 mm 50 0274320000
MK 3/8 72.75 mm 55.5 mm 25 0274420000
MK 3/9 82 mm 55.5 mm 25 0274520000
MK 3/10 91.25 mm 74.0 mm 20 0274620000
MK 3/12 110 mm 92.5 mm 20 0243520000
Type Qty Order No.
BSTB 28/12 MK U 1-12 50 0245900000
BSTB 28/8 MK U 1-8 50 0290200000
BSTB 28/6 MK U 1-6 50 0290000000
BSTO 28/12 MK 50 0245800000
BSTO 28/8 MK3/8 50 0284700000
BSTO 28/6 MK 50 0289500000
BSTO 28/4 MK3/4 50 0289300000
Accessories
Multi-pole terminal strips for direct mounting
G
G.13
MK 4/16 2.5 mm²
17 x 16 / 3.4
Refer to order data
0.2...4
IEC UL CSA
400 150 150
24 20 15
2.5 AWG 22...12 AWG 22...12
6 / 3
A2 / 5VA
? r # a
Rated connection
0.5...4 / 1.5...2.5
0.5...2.5 / 0.5...1.5
0.4...0.45 Nm (M 2.5)
5 / 0.6 x 3.5 mm
IEC 60947-7-1
Type
Length/Mounting dimensions
Qty Order No.
MK 4/16 103 mm 85.5 mm 20 0244220000
Type Width Qty Order No.
BSTB 28/16 MK U 1-16 50 0262200000
BSTB 28/16 MK O 1-16 50 0278700000
BSTO 28/16 MK 4/16 50 0262100000
MK 6/2...6/6 6 mm²
23 x 22 / 3.4
Refer to order data
0.33...6
IEC UL CSA
690 300 300
41 30 40
6 AWG 22...10 AWG 22...10
8 / 3
A3 / 5VA
r # i a
Rated connection
0.5...6 / 1.5...6
0.5...6 / 0.5...4
1.2...2.0 Nm (M 4)
9 / 4.0 x 0.8 mm
IEC 60947-7-1
Type
Length/Mounting dimensions
Qty Order No.
MK 6/2 23.5 mm 50 0620420000
MK 6/3 36.5 mm 13.0 mm 50 0620320000
MK 6/4 49.5 mm 26.0 mm 20 0620220000
MK 6/6 75.5 mm 52.0 mm 20 0620120000
Type Width Qty Order No.
MK 10/14 2.5 mm²
13.5 x 12 / 3.1
Refer to order data
0.21...4
IEC UL CSA
125 150 300
24 25 10
2.5 AWG 22...12 AWG 24...12
3 / 3
A2 / V2
r # a
Rated connection
0.5...4 / 1.5...2.5
0.5...2.5 / 0.5...1.5
0.4...0.45 Nm (M 2.5)
6 / 0.6 x 3.5 mm
IEC 60947-7-1
Type
Length/Mounting dimensions
Qty Order No.
MK 10/14 88.5 mm 20 0370160000
Type Width Qty Order No.
Accessories
Multi-pole terminal strips for direct mounting
G
G.14
Screw connection
Technical data
Rated data
Rated voltage V
Rated current A
Rated cross-section mm²
Rated impulse voltage / Pollution severity kV/-
Gauge to IEC 60947-1 / UL94 Flammability class
Approvals
Clamped conductors (H05V/H07V)
solid / stranded mm²
flexible / Stranded wire with end ferrules mm²
Tightening torque range (clamping screw)
Stripping length / Blade size mm/-
Note
Width/Height/ø mounting hole mm
Length / mounting dimensions
Max. clamping range mm²
Version
2-pole
3-pole
4-pole
6-pole
10-pole
12-pole
Note
For detailed information on other accessories and ap-
plications, refer to the „Accessories“ section
Lid / cover
Marking strips, printed
Printed
Marking strips, unprinted
Unprinted
MK 5/2 0.DE 2.5 mm²
18 x 14 / 4.2
Refer to order data
0.2...4
Type
Length/Mounting dimensions
Qty Order No.
MK 5/2 O.DE
40 mm 32.0 mm 100 0243820000
Type Width Qty Order No.
D 2 MK5/2 PA/NA 18 mm 50 0244060000
Ordering data
(see assortment in catalogue 7)
IEC UL CSA
500
24
2.5
6 / 3
A2 / 5VA
r #
Rated connection
0.5...4 / 1.5...2.5
0.5...2.5 / 0.5...1.5
0.4 NmM 2.5
5 / 0.6 x 3.5 mm
Accessories
KS 2...10 2.5 mm²
25 x 17.5 / 4.2
Refer to order data
0.2...4
IEC UL CSA
500 300 300
24 20 25
2.5 AWG 22...12 AWG 24...12
6 / 3
A2 / 5VA
r # a
Rated connection
0.5...4 / 1.5...2.5
0.5...2.5 / 0.5...1.5
0.5...0.7 Nm (M 3)
8 / 4.0 x 0.8 mm
IEC 60947-7-1
Type
Length/Mounting dimensions
Qty Order No.
KS 2 O.D2 42 mm 32.0 mm 100 0134420000
KS 4 O.D4 66 mm 56.0 mm 50 0140320000
KS 6 O.D6 90 mm 80.0 mm 50 0140620000
KS 10 O.D10
138 mm 128.0 mm 20 0141620000
Type Width Qty Order No.
D2 KS2 TP 25 mm 100 0134500000
D4 KS4 TP 48 mm 50 0140500000
D6 KS6 TP 72 mm 50 0140800000
D10 KS10 TP 120 mm 20 0141800000
ELSB 2 BEZ. 1-2 50 0143200000
ELSB 4 BEZ. 1-4 50 0143300000
ELSB 6 BEZ. 1-6 50 0143400000
ELSB 10 BEZ. 1-10 50 0143500000
ELSO 2 F.KS 2 50 0142800000
ELSO 4 F.KS 4 50 0142900000
ELSO 6 F.KS 6 50 0143000000
ELSO 10 F.KS 10 50 0143100000
Accessories
Multi-pole terminal strips for direct mounting
G
G.15
BK 2...12 4 mm²
22 x 20 / 3.4
Refer to order data
0.33...4
IEC UL CSA
400 300 300
32 10 10
4 AWG 22...12 AWG 22...12
6 / 3
A3 / 5VA
# a
Rated connection
0.5...4 / 1.5...4
0.5...4 / 0.5...4
0.5...0.6 Nm (M 3)
8 / 4.0 x 0.8 mm
IEC 60947-7-1
2 single-wire conductors with same cross-section (0.5...1.5 mm²) can be
connected.
Type
Length/Mounting dimensions
Qty Order No.
BK 2 CRN 20 mm 100 0624720000
BK 3 CRN 31 mm 11.0 mm 100 0624920000
BK 4 CRN 38 mm 18.0 mm 100 0625120000
BK 6 CRN 52 mm 32.0 mm 50 0625220000
BK 12 CRN
92 mm 72.5 mm 25 0625320000
Type Width Qty Order No.
BSTB 28/2 BK U 1-2 50 0203600000
BSTB 28/4 BK U 1-4 50 0197300000
BSTB 28/6 BK U 1-6 50 0197500000
BSTB 28/12 BK U 1-12 50 0198800000
BSTO 28/2 BK 50 0203500000
BSTO 28/3 BK 50 0203700000
BSTO 28/4 BK 50 0197200000
BSTO 28/6 BK 50 0197400000
BSTO 28/12 BK 50 0198700000
Accessories
Multi-pole terminal strips for direct mounting
G
G.16
Screw connection
ATEX approval
Technical data
Rated data
Rated voltage V
Rated current A
Rated cross-section mm²
Rated impulse voltage / Pollution severity kV/-
Gauge to IEC 60947-1 / UL94 Flammability class
Approvals
Clamped conductors (H05V/H07V)
solid / stranded mm²
flexible / Stranded wire with end ferrules mm²
Tightening torque range (clamping screw)
Stripping length / Blade size mm/-
Note
Width/Height/ø mounting hole mm
Length / mounting dimensions
Max. clamping range mm²
Version
2-pole
3-pole
4-pole
5-pole
6-pole
7-pole
8-pole
9-pole
10-pole
11-pole
12-pole
Note
For detailed information on other accessories and ap-
plications, refer to the „Accessories“ section
Marking strips, printed
Printed
Marking strips, unprinted
Unprinted
BK 2...12/E 4 mm²
22 x 20 / 3.4
Refer to order data
0.33...4
2 single-wire conductors with same cross-section (0.5...1.5 mm²) can be
connected.
Type
Length/Mounting dimensions
Qty Order No.
BK 2/E 20 mm 100 7906040000
BK 3/E 31 mm 11.0 mm 100 7906060000
BK 4/E 38 mm 18.0 mm 100 7906080000
BK 6/E 52 mm 32.0 mm 50 7906090000
BK 12/E 92 mm 72.5 mm 25 7906100000
Type Qty Order No.
BSTB 28/2 BK U 1-2 50 0203600000
BSTB 28/4 BK U 1-4 50 0197300000
BSTB 28/6 BK U 1-6 50 0197500000
BSTB 28/12 BK U 1-12 50 0198800000
BSTO 28/2 BK 50 0203500000
BSTO 28/3 BK 50 0203700000
BSTO 28/4 BK 50 0197200000
BSTO 28/6 BK 50 0197400000
BSTO 28/12 BK 50 0198700000
Ordering data
(see assortment in catalogue 7)
IEC UL CSA
400
32
4 AWG 22...12 AWG 22...12
6 / 3
A3 / 5VA
# a
Rated connection
0.5...4 / 1.5...4
0.5...4 / 0.5...4
0.5...0.6 Nm (M 3)
8 / 4.0 x 0.8 mm
Accessories
IEC 60947-7-1
MK 3/2...12/E 2.5 mm²
15 x 16.1 / 3.45
Refer to order data
0.33...4
IEC UL CSA
400
24
2.5 AWG 22...12 AWG 22...12
6 / 3
A2 / 5VA
#
Rated connection
0.5...4 / 1.5...2.5
0.5...2.5 / 0.5...1.5
0.4...0.45 Nm (M 2.5)
5 / 0.6 x 3.5 mm
IEC 60947-7-1
Type
Length/Mounting dimensions
Qty Order No.
MK 3/2/E 17.4 mm 18.5 mm 100 7906110000
MK 3/3/E 26.5 mm 18.5 mm 100 7906120000
MK 3/4/E 35.75 mm 18.5 mm 50 7906130000
MK 3/5/E 45 mm 18.5 mm 50 7906140000
MK 3/6/E 54.25 mm 37.0 mm 50 7906150000
MK 3/7/E 63.5 mm 37.0 mm 25 7906160000
MK 3/8/E 72.75 mm 55.5 mm 25 7906170000
MK 3/9/E 82 mm 55.5 mm 25 7906180000
MK 3/10/E 91.25 mm 74.0 mm 25 7906190000
MK 3/11/E 100.5 mm 74.0 mm 20 7906200000
MK 3/12/E 110 mm 92.5 mm 25 7906210000
Type Qty Order No.
BSTB 28/12 MK U 1-12 50 0245900000
BSTB 28/8 MK U 1-8 50 0290200000
BSTB 28/6 MK U 1-6 50 0290000000
BSTO 28/12 MK 50 0245800000
BSTO 28/8 MK3/8 50 0284700000
BSTO 28/6 MK 50 0289500000
BSTO 28/4 MK3/4 50 0289300000
Accessories
Multi-pole terminal strips for direct mounting
G
G.17
MK 6/2...6/E 6 mm²
23 x 22 / 3.4
Refer to order data
0.33...6
IEC UL CSA
690
41
6 AWG 22...10 AWG 22...10
8 / 3
A3 / 5VA
#
Rated connection
0.5...6 / 1.5...6
0.5...6 / 0.5...4
1.2...2.0 Nm (M 4)
9 / 4.0 x 0.8 mm
IEC 60947-7-1
Type
Length/Mounting dimensions
Qty Order No.
MK 6/2/E 23.5 mm 50 7906220000
MK 6/3/E 36.5 mm 13.0 mm 50 7906230000
MK 6/4/E 49.5 mm 26.0 mm 20 7906240000
MK 6/5/E 62.5 mm 26.0 mm 20 7906250000
MK 6/6/E 75.5 mm 52.0 mm 20 7906260000
Type Width Qty Order No.
Accessories
Multi-pole terminal strips for direct mounting
G.18
Accessories
G
Busbar overview
In switchgears and controls, it may be necessary to bring the
neutral conductor and the protective conductor together at a
central point. Busbars are available for this purpose and can be
used for connecting a large number of conductors in a confined
space (up to 70 conductors on a 1 m busbar). The conductors
are connected by means of a screw clamp or tension clamp.
usbars are held in position by pressure clamps or screw clamps
onto the busbar holders. The cable clamps can be pushed on
the busbar and adjusted to the entire wiring in the system. The
busbars can be used unperforated in any lengths. They are fixed
using the SH busbar holder which can, for longer busbars, also
be positioned between the clamps.
In order to bring together neutral conductors and protective
conductors at a central point, it is advantageous to use ZB cable
clamps together with 10 x 3 or 6 x 6 busbars. The cable clamps
can be pushed onto the busbar and adjusted to the entire wiring
in the system. The cable clamp serves as the protective conduc-
tor connection and can be supplied with green/yellow insulating
caps. These caps indicate the protective function and marking
tags allow clear identification of each conductor. If the cable
clamps are used to connect neutral conductors, they can be
marked with a blue insulating cap.
ZBE 6 can also be swivelled onto the busbar retrospectively
Cable clamps
Busbars
G.19
Accessories
G
Busbars
Busbars, unperforated
Busbars, perforated
SSch
Type Material Cross-section Length Current carrying capacity Qty. Order No.
SSch 10 x 3 Copper, tin-plated 10 x 3 mm 1 m 140 A 1 0348900000
SSch 10 x 3 Steel, galvanised 10 x 3 mm 1 m 1 0438000000
SSch 10 x 3 Brass, blank 10 x 3 mm 1 m 100 A 1 0259800000
SSch 6 x 6 Copper, tin-plated 6 x 6 mm 1 m 140 A 1 0571300000
SSch 6 x 6 Brass, blank 6 x 6 mm 1 m 100 A 1 0571200000
SSch 15 x 6 Copper, tin-plated 15 x 6 mm 1 m 265 A 1 0357400000
NSch / ESch
Type Material Cross-section Length Current carrying capacity Qty. Order No.
NSch 15 x 2 Copper, blank 15 x 2 mm 1 m 80 A 1 0280200000
ESch 12 x 2 Steel, galvanised 12 x 2 mm 1 m 1 0280300000
Pressure piece Qty. Order No.
DKSUE 100 0280100000
Clamping screw Qty. Order No.
BFSC M5 x 8 100 0296700000
Connection data NSch / ESch
Screw connection solid 0.5 ... 2.5 mm2
Stripping length 9 mm
Cable lug connection max. 16 mm2
Max. current per connection 27 A
G.20
Accessories
G
Busbars
Busbar holders
With clip and base
With metal bridge
With metal bridge
SH
Type Figure For busbar cross-section Qty. Order No.
SH 1 TS 15 complete 1. 10 x 3, 6 x 6, 15 x 2, 12 x 2 20 0299860000
2. 15 x 2, 15 x 6
Individual parts SH1
SH 1 Base 20 0401460000
SH 1 Clip 500 0635960000
Fixing screw for SH1
BFSC M4x9 for 1 SH1 100 0103300000
BFSC M4x30 for 2 SH1 stacked 50 0267100000
Type For busbar cross-section Qty. Order No.
SH 2S 10 x 3, 6 x 6, 15 x 6, 10 x 5 10 0641720000
Type Qty. Order No.
SH 2 The arrangement of mounting rails in totally 10 0494920000
insulated facilities
Type For busbar cross-section Qty. Order No.
SH 3 10 x 3, 6 x 6, 10 x 5 10 0556660000
26.5
24.5
12.5
10.5
6.5
24.5
15
2
1
24
20.6
26
5.7
40
35.5
21
6.5
22.2
32
2
15
40
5.7
40
22.2
2
6.5
15
40
21
65
4.5
65
4.5
45 4.5
55
10
32.5
15
26.5
24.5
12.5
10.5
6.5
24.5
15
2
1
24
20.6
1. 2.
G.21
Accessories
G
Busbar holders
Connection element
WEW
Type For busbar cross-section Qty. Order No.
WEW 35/1 10 x 3, 6 x 6 50 1059000000
WEW 35/2 10 x 3, 6 x 6 100 1061200000
WEW 35/1 and WEW35/2 as
busbar holder together with
the ZB 4 G tension clamp
AK 95
Type For busbar cross-section Qty. Order No.
AK 95 15 x 6 mm 10 0364200000
The AK 95 connection element is used as a tension clamp for 15 x 6 busbars Connection
cross-sections: e = 6…16 mm2
f = 6…50 mm2
m = 16…50 mm2
36
36
10
M6
Busbars
G.22
Accessories
G
Busbars
ZB / ZBE
Type Colour Dimensions [mm] Qty. Order No.
a width c h1
ZB 4, blank - 11.7 5.6 16.0 10.0 50 0316500000
Insulating cap blue 50 0475480000
Insulating cap green / yellow 50 0475460000
ZBE 6, blank - 19.5 8.2 19.5 19.0 50 0459500000
Insulating cap blue 50 0526080000
Insulating cap green / yellow 50 0526060000
ZB 10, blank - 19.5 8.2 19.5 19.0 50 1261300000
ZB 16, blank - 17.0 10.0 16.0 17.0 50 0316600000
Insulating cap blue 50 0502980000
Insulating cap green / yellow 50 0502960000
ZB 35, blank - 21.0 14.4 18.4 20.5 20 0266500000
Insulating cap blue 50 0502780000
ZB
Type Colour Dimensions [mm] Qty. Order No.
a b c h1
ZB 4/6, blank 14.7 5.6 12.5 10.0 50 0556700000
ZB 16/6, blank 19.0 10.0 12.5 17.0 50 0556800000
Cable clamp, uninsulated
For 10 x 3 mm busbars
Connection cross-section:
Solid 0.5 ... 6.0 mm2
Flexible 0.5 ... 4.0 mm2
Stranded -
Clamping screw M 3
Stripping length 16 mm
For retrofitting
Connection cross-section:
Solid 1.0 ... 10 mm2
Flexible 1.5 ... 10 mm2
Stranded -
Clamping screw M 4
Stripping length 19 mm
Also for 10 x 5 mm busbar
Connection cross-section:
Solid 1.5 ... 10 mm2
Flexible 2.5 ... 10 mm2
Stranded -
Clamping screw M 4
Stripping length 19 mm
Connection cross-section:
Solid 2.5 ... 16 mm2
Flexible 2.5 ... 16 mm2
Stranded 16 ... 25 mm2
Clamping screw M 4
Stripping length 16 mm
Connection cross-section:
Solid -
Flexible 16 ... 35 mm2
Stranded 16 ... 50 mm2
Clamping screw M 6
Stripping length 19 mm
For 6 x 6 mm busbar
Connection cross-section:
Solid 0.5 ... 6,0 mm2
Flexible 0.5 ... 4,0 mm2
Stranded -
Clamping screw M 3
Stripping length 16 mm
Connection cross-section:
Solid 2.5 ... 16 mm2
Flexible 2.5 ... 16 mm2
Stranded 16 ... 25 mm2
Clamping screw M 4
Stripping length 12 mm
G.23
Accessories
G
Busbars
ZB / ZBE /ZF
Type Colour Dimensions [mm] Qty. Order No.
a2 width d h2
ZB 4 G GN/GE green/yellow 27.0 7.6 19.7 15.5 50 0322160000
ZB 4 G BL blue 27.0 7.6 19.7 15.5 50 0322180000
ZB 4 G SW black 27.0 7.6 19.7 15.5 50 0322110000
ZB 4K GN/GE grün/gelb 18.5 6.0 19.0 13.0 50 0475360000
ZB 4K BL blue 18.5 6.0 19.0 13.0 50 0475380000
ZBE 6K GN/GE green/yellow 27.0 8.0 22.5 23.0 50 0525960000
ZBE 6K BL blue 27.0 8.0 22.5 23.0 50 0525980000
ZBE 6K SW black 27.0 8.0 22.5 23.0 50 0525910000
ZB 16K GN/GE green/yellow 24.0 10.0 19.2 20.0 50 0502860000
ZB 16K BL blue 24.0 10.0 19.2 20.0 50 0502880000
ZB 35K GN/GE green/yellow 25.0 14.4 32.0 20.5 20 0502660000
ZB 35K BL blue 25.0 14.4 32.0 20.5 20 0502680000
ZB 35K SW black 25.0 14.4 32.0 20.5 20 0502610000
ZF 4 S beige 22.0 6.1 24.5 - 50 1814680000
ZF 4 S BL blue 22.0 6.1 24.5 - 50 1814660000
ZF 4 S GN/GE green/yellow 22.0 6.1 24.5 - 50 1814670000
ZB
Type Colour Dimensions [mm] Qty. Order No.
a2 b d h2
ZB 4/6K GN/GE green/yellow 21.2 6.0 25.0 14.0 50 0565460000
ZB 4/6K BL blue 21.2 6.0 25.0 14.0 50 0565480000
ZB 16/6K GN/GE green/yellow 26.0 9.7 25.0 20.0 50 0569660000
Cable clamp, insulated
For 10 x 3 mm busbars
Connection cross-section:
Solid 0.5 ... 6.0 mm2
Flexible 0.5 ... 4.0 mm2
Stranded -
Clamping screw M 3
Stripping length 16 mm
For retrofitting
Connection cross-section:
Solid 1.0 ... 10 mm2
Flexible 1.5 ... 10 mm2
Stranded -
Clamping screw M 4
Stripping length 19 mm
Connection cross-section:
Solid 2.5 ... 16 mm2
Flexible 2.5 ... 16 mm2
Stranded 16 ... 25 mm2
Clamping screw M 4
Stripping length 16 mm
Connection cross-section:
Solid -
Flexible 16 ... 35 mm2
Stranded 16 ... 50 mm2
Clamping screw M 6
Stripping length 19 mm
Tension clamp connection
Connection cross-section:
Solid 0.5 ... 4.0 mm2
Flexible 0.5 ... 2.5 mm2
Stranded -
Stripping length 10 mm
For 6 x 6 mm busbar
Connection cross-section:
Solid 0.5 ... 6.0 mm2
Flexible 0.5 ... 4.0 mm2
Stranded -
Clamping screw M 3
Stripping length 16 mm
Connection cross-section:
Solid 2.5 ... 16 mm2
Flexible 2.5 ... 16 mm2
Stranded 16 ... 25 mm2
Clamping screw M 4
Stripping length 12 mm
G.24
Accessories
G
Overview Terminal rails
Both active and passive components and intelligent modules are
mounted on terminal rails – a method which has proven its orth
over the years. But it is only after the use of certain consum-
ables – which are frequently not taken into consideration – that
electrical installation is finally completed. In this chapter, users
will find a range of terminal rails and profile rails for component
installation together with end brackets for holding and isolating
the components. This guarantees firm installation and isolation.
Weidmüller supplies components which show perfect functional
compatibility.
Terminal rails are made of either steel, stainless steel, aluminium,
copper or plastic, depending on the area of application.
Stainless steel
Stainless steel is a collective noun for all kinds of steel (alloys)
which are smelted in a special process and have a high degree
of purity. Stainless steel has much-enhanced resistance to cor-
rosion. Weidmüller’s stainless steel terminal rails have the follow-
ing composition: X5 CrNi 18-10 stainless steel (i.e. ~ 18 % chro-
mium, ~ 10 % nickel).
Aluminium
Aluminium is second only to copper in its electrical conductivity.
One advantage is its light weight. Aluminium oxidises quickly in
air; thus passivated, it offers excellent corrosion protection.
Copper
Copper, a heavy metal, has the best electrical conductivity of all
metals used. As it is a soft metal, Weidmüller’s terminal rails are
2.3 mm thick.
Plastic
The plastic terminal rail scores on two counts: firstly, its insulat-
ing properties, and secondly, its low weight. This leads to its use
in special applications where, for example, clearance and creep-
age distances with respect to the mounting plate cannot be
achieved with the standard terminal rails.
Steel
Weidmüller started developing RoHS-compliant surfaces at a
very early stage to meet the requirements of EU directives. This
commitment is now paying off because Weidmüller products
comply with the statutory instruments at an early date and
provide you, the customer, with the customary, high Weidmüller
quality. All the yellow-passivated surfaces so well known to
users will in future be replaced by terminal rails with the new
WIN-Q surface finish. This name stands for the Weidmüller
quality, in other words excellent surface protection and, at the
same time, excellent electrical properties.
A terminal rail can also be used as a protective conductor bus-
bar. Weidmüller PE / earth terminals in the W-Series, Z-Series,
I-Series, SAK- and AKZ-Series comply with requirements stipu-
lated in IEC 60 947-7-2. According to VDE 0100 part 540, for
conductors with cross-sectional areas exceeding 10 mm2, both
protective and neutral conductors may be grouped together as
a single category of conductors designated PEN.
If a terminal rail is used as a PEN busbar, the following criteria
must be observed:
• Only E-Cu or aluminium profiles are allowed
• Short-circuit currents and thermal rated currents must be
taken into account
• The terminal rails are to be insulated as a contribution to
protective insulation
Terminal rail systems
G.25
Accessories
G
Overview Terminal rails
All unperforated terminal rails can be provided with
fixing holes (state dimensions h and l2).
Possible diameters are 3.5 / 5.6 / 5.5 / 7 mm.
All unperforated steel rails can also be supplied with
welded on steel studs (state dimension a and required studs).
I1
I2
35
h
I1
I2
35
h
S 35
S 32
S 15
Stud
Stud
Stud
M 5x8
M 6x12
M 5x8
M 6x12
M 5x6
a
a
a
TS 15
TS 32
TS 35
U
15 mm
5,5 mm
Y
32 mm
5,5 mm
W
35 mm
7,5 mm
V
35 mm
15 mm
G.26
Accessories
G
Terminal rails
TS 15 x 5
Aluminium Short-circuit strength Material thickness Length Qty. Order No.
TS 15x5 2M/AL/BK 16 mm21 mm 2 m 10 m 0134700000
(max. permissible rated current for PEN function = 76 A)
Steel, galvanised and passivated
TS 15x5 2M/ST/ZN 10 mm21 mm 2 m 2 m 0514200000
Aluminium Short-circuit strength Material thickness Length Qty. Order No.
TS 15x5/LL 2M/AL/BK 16 mm21 mm 2 m 2 m 0217900000
(max. permissible rated current for PEN function = 76 A)
Steel, galvanised and passivated
TS 15x5/LL 2M/ST/ZN 10 mm21 mm 2 m 2 m 0117500000
TS 15x5/LL 1M/ST/ZN 10 mm21 mm 1 m 10 m 0117510000
TS 32 x 15
Aluminium Short-circuit strength Material thickness Length Qty. Order No.
TS 32X15 2M/AL/BK 70 mm21.5 mm 2 m 2 m 0169300000
(max. permissible rated current for PEN function = 192 A)
Steel, galvanised and passivated
TS 32X15 2M/ST/ZN 35 mm21.5 mm 2 m 2 m 0122800000
Copper
TS 32X16.2 2M/CU/BK 120 mm22.1 mm 2 m 2 m 0364300000
(max. permissible rated current for PEN function = 269 A)
Stainless steel
TS 32X15 2M/CRN 35 mm21.5 mm 2 m 2 m 0293220000
Steel, galvanised and passivated Short-circuit strength Material thickness Length Qty. Order No.
TS 32X15/LL 2M/ST/ZN 35 mm21.5 mm 2 m 2 m 0514400000
TS15 terminal rail
Unperforated
With slotted hole
TS 32 terminal rail
Unperforated
With slotted hole
U
15 mm
5,5 mm
Y
32 mm
5,5 mm
G.27
Accessories
G
Terminal rails
TS 35 x 7.5
Aluminium Short-circuit strength Material thickness Length Qty. Order No.
TS 35X7.5 2M/AL/BK 35 mm21 mm 2 m 2 m 0330800000
(max. permissible rated current for PEN function = 125 A)
Steel, galvanised and passivated
TS 35X7.5 2M/ST/ZN 16 mm21 mm 2 m 2 m 0383400000
TS 35X7.5 1M/ST/ZN 16 mm21 mm 1 m 10 m 0383410000
Stainless steel
TS 35X7.5 2M/CRN 16 mm21 mm 2 m 2 m 1747350000
Steel, galvanised and passivated Short-circuit strength Material thickness Length Qty. Order No.
TS 35X7.5/LL 2M/ST/ZN 16 mm21 mm 2 m 2 m 0514500000
TS 35X7.5/LL 1M/ST/ZN 16 mm21 mm 1 m 10 m 0514510000
TS 35X7.5/LL/6 2M/ST/ZN 16 mm21 mm 2 m 2 m 0514570000
TS 35 x 15
Copper Short-circuit strength Material thickness Length Qty. Order No.
TS 35X15/2.3 2M/CU/BK 150 mm22.3 mm 2 m 2 m 0270100000
(max. permissible rated current for PEN function = 309 A)
Steel, galvanised and passivated
TS 35X15/2.3 2M/ST/ZN 50 mm22.3 mm 2 m 2 m 0498000000
Aluminium
TS 35X15/2.3 2M/AL/BK 70 mm22.3 mm 2 m 2 m 1848290000
(max. permissible rated current for PEN function = 192 A)
Steel, galvanised and passivated Short-circuit strength Material thickness Length Qty. Order No.
TS 35X15 2M/ST/ZN 25 mm21.5 mm 2 m 2 m 0236400000
Steel, galvanised and passivated Short-circuit strength Material thickness Length Qty. Order No.
TS 35X15/LL 2M/ST/ZN 25 mm21.5 mm 2 m 2 m 0236500000
TS 35X15/LL 1M/ST/ZN 25 mm21.5 mm 1 m 10 m 0236510000
TS 35X15LL/5 2M/ST/ZN 25 mm21.5 mm 2 m 2 m 1837380000
TS 35X15/LL/6x18 2M/ST/ZN 25 mm21.5 mm 2 m 2 m 1805980000
TS 35X15/LL/6x25 2M/ST/ZN 25 mm21.5 mm 2 m 2 m 1866290000
TS 35 x 7,5 terminal rail
Unperforated
With slotted hole
Unperforated
Unperforated
With slotted hole
6.3
11
25
6.3
7
18
6.2
7
18
5.2
7
18
W
35 mm
7,5 mm
V
35 mm
15 mm
TS 35 x 15 terminal rail
G.28
Accessories
G
Terminal rails
TSK 35 x 15
Plastic PVC RAL 7035 Length Qty. Order No.
TSK 35X15 2M PVC/GR 2 m 2 m 0514300000
TS 35 x 15 terminal rail
Unperforated
V
35 mm
15 mm
G.29
Accessories
G
Terminal rails
EW 15/2
EW 15
ZEW 15
EWK 1
EWK 1 ALT
EWK 2
EW 35
WEW 35/1
WEW 35/2 ZEW 35/2
End brackets
For TS 15 terminal rail
For terminal rail TS 32
For terminal rail TS 35
Polyamide 66, screw-in Colour Torque Qty. Order No.
EWK AKA 2.5 beige 0.4 Nm 50 0348660000
EW 15 beige 0.4 Nm 50 0382860000
Polyamide with fibreglass, screw-in
EW 15/2 dark beige 0.4 Nm 50 1071900000
Polyamide 66, screwless
ZEW 15 beige 20 7920340000
Polyamide 66, screw-in Colour Torque Qty. Order No.
EWK 2 beige 1.2 Nm 50 0199360000
EWK 1 TS 32 M4X18 beige 1.2 Nm 50 0206160000
EWK 1 ALT beige 0.6 Nm 50 0495160000
Polyamide with fibreglass, screw-in
WEW 32/1 dark beige 0.5 Nm 50 1067600000
Polyamide 66, screw-in Colour Torque Qty. Order No.
EW 35 beige 0.5 Nm 50 0383560000
EW 35 GR grey 0.5 Nm 50 0383530000
Polyamide with fibreglass, screw-in
WEW 35/1 dark beige 1.2 Nm 50 1071900000
WEW-35/2 dark beige 0.5 Nm 100 1061200000
Polyamide 66, screwless
ZEW (6 mm) beige 20 9540000000
ZEW 35/2 (8 mm) beige 20 8630740000
G.30
Accessories
G
Terminal rail supports / Mounting feet
Terminal rail supports
Thread Qty. Order No.
TSTW 5/M5 M5 10 0178100000
TSTW 5/M5 galvanised M6 10 1779100000
TSTW 6/M6 M5 10 0164000000
TSTW D 4.3 Hole ø 4.3 mm 10 1610110000
Terminal rail supports of type TSTW are used for
angled fixing of terminal rails at an angle of 35°.
TST 2/M5 M5 10 1286600000
TST 2/M6 M6 10 0101700000
The TST terminal rail support is used for assembly
of terminal rails in a frame or over a cut-out
Fixing screws
FKSC M5x8 Ø9 50 0295900000
FKSC M6x8 Ø9 50 0642600000
FKSC M6x12 Ø9 50 0353500000
Weidmüller supplies fixing screws with hexagonal sockets and a very low
head for the terminal rail supports so that the terminals can also be fitted
over the screw.
Terminal rails
TSTW D 4.3TSTW 6/M6
TST
G.31
Accessories
G
Terminal rail supports / Mounting feet
Mounting feet
Clip-on foot, steel for TS 35 Thread Qty. Order No.
FM 4 M4 40 0687900000
FM 5 M5 40 0636800000
FM 6 M6 40 0636900000
FM 4.2 Hole ø 4.2 mm 40 1724580000
Mounting foot, PA orange for TS 35
MOFU 35/LO/1 with holes 20 0646260000
MOFU 35 20 0495660000
Sliding nut for TS 32 Colour
MB M3/M5 M3 und M5 creme 20 0503500000
MB M5/M3 M5 und M3 black 20 0553400000
MB M6/M4 M6 und M4 grey 20 0334900000
The sliding nut for the RS 32 terminal rail has
two threaded holes for screws M3 + M5 / M6 + M4 / M5 + M3.
It is used to fasten components which cannot be slotted
directly onto the TS 32, in particular the smaller TS 15 top hat rail.
This enables, for example, mini-terminals to be snapped
onto the TS 15 first, and this rail is then fastened together
with the terminals to the TS 32 using the sliding nut.
Terminal rails
FM
MOFU 35/LO/1
MOFU 35
MB
G.32
Accessories
G
Terminal rails
To save costs, it is possible to dispense with an expensive
die cast aluminium enclosure within a control cabinet by using
RailMate, which provides ingress protection class IP20.
The terminal rail assembly system can be used to mount
the inserts of the heavy-duty plug-in connectors and also
the “ConCept” modular plug-in connector system on the
terminal rail. This is all done without tools, simply by clipping
the parts on.
A large surface at the base of the insert receptacle and on the
frame allow for clear identification of equipment.
In the control cabinet, RailMate lets the user accommodate the
maximum number of electrical connections in a minimum area.
RailMate terminal rail system
for the TS 35 x 7.5 and TS 35 x 15 terminal rails
G.33
Accessories
G
Terminal rails
Base plate
with slider
2 insert receptacle bottoms
Rider
(adjusts to sizes 3, 4, 6 and 8)
Insert receptacle frame
for sizes 3, 4, 6 and 8
RailMate terminal rail assembly system
Ordering data individual components
Type For inserts of size Qty. Order No.
Insert receptacle frame
HDC RailMate HB6 Top 3 10 1797540000
HDC RailMate HB10 Top 4 10 1797550000
HDC RailMate HB16 Top 6 10 1797560000
HDC RailMate HB24 Top 8 10 1797570000
Base plate, rider and 2 insert receptacle bottoms
HDC RailMate Basis 3, 4, 6, 8 1 1797580000
Technical data
Material PC
Properties Phosphorous and halogen free
Colour grey (RAL 7032)
Temperature range –40°C ... +125 °C
Flammability class V-0 to UL 94
Accessories
Type Qty. Order No.
Coding set
HDC RailMate COS 50 poles and plugs 1 1798260000
6 different coding versions
Marking labels for laser printer (1 sheet = 264 labels)
LM MT 300 20/8 silver 10 sheets 1686380001
LM MT 300 20/8 white 10 sheets 1686381044
LM MT 300 20/8 yellow 10 sheets 1686381687
Marking labels for thermotransfer printer (1 roll = 10,000 labels)
THM MT30X 32/9 silver 1 roll 1751770001
LM MT 300 20/8 white 1 roll 1751771044
LM MT 300 20/8 yellow 1 roll 1751771687
Ordering data sets
Type For inserts of size Qty. Order No.
HDC RailMate HB6 Set 3 1 1797500000
HDC RailMate HB10 Set 4 1 1797510000
HDC RailMate HB16 Set 6 1 1797520000
HDC RailMate HB24 Set 8 1 1797530000
Each set consists of: 1 base plate
1 slider
2 insert receptacle bottoms
1 insert receptacle frame
Dimensions
Top
Base
G.34
Accessories
G
Terminal markers
Terminal markers
Weidmüller’s multitude of different terminal markers enable users
to solve virtually every labelling task of all types of wire and cable
connectors. Whether multi-character labelling, ready-to-use
markers with standard printing or individual, custom markers,
whether white or coloured or group designations at terminals,
the comprehensive range of Weidmüller products solves every
marking task simply, quickly and clearly.
The tables on the following pages show which markers fit the
various terminal series. The terminal pitch governs the selection
of a marker. For example, a WDU 2.5 terminal has a pitch of
5 mm, the WS 12/5 marker is 12 mm long and suitable for a
5 mm pitch.
Whole blocks of terminals can be marked as a strip using the
Weidmüller system. When a terminal with a larger pitch has to
be marked (e.g. WDU 16), a smaller marker (e.g. WS 12/5) can
be clipped onto it. Most of the markers are compatible with
each other.
The two traditional marker series, DEK and WS, are available
as ready-to-use markers. And these markers are also available
in the MultiCard format for printing by users themselves.
MultiCard – the concept for labelling with the SMark Laser, Print-
Jet, Plotter or MC-Mobilo.
To see a small selection of the Weidmüller markers, order our
bag of samples, order No. 1646670000.
W series
Z series
I series
P series
Owing to the sheer number of possible applications and environmental influ-
ences such as moisture, radiation, gases or heat/cold to which the products
can be exposed, Weidmüller accepts no liability for the suitability of products
in all customer applications. Suitability tests for specific applications must
therefore be carried out by the customer. However, Weidmüller will be happy
to provide help and advice upon request.
Due to the different identification system available on the market, we wish
to point out that Weidmüller does not guarantee industrial identification
products if the Weidmüller components (markers – transparent sleeves – ink/
toner/colour ink ribbons – printing systems) are combined with third-party
products, unless Weidmüller has explicitly agreed for the purpose of an
individual application.
G.35
Accessories
G
Terminal markers – Selection table
Designation
Terminal
width
DEK
WS
ZS
SchT 7
SchT 9/4
SchT 14/6
WTS 3/4
WGB 5 /
WAD 5
WGB 8/
WAD 8
WAD 12
WAD 27
ZGB 15 /
ZGB 30
BZT 1
BZT 2
EM 8/30
AKE 2.5/AKZ 2.5... 55--------------
AKZ 1.5... 55--------------
AKZ 4.../AKB 4... 668/5--x----------
BZT ZVL 1.5 5.08 512/5-------------
DLA 2.5... 66 8/5 - x x x - - - - - - - - -
DLD 2.5... 66 8/5 - x x x - - - - - - - - -
DLI 2.5 66 8/5 - x x x - - - - - - - - -
EW 15 9.5 5 12/5 - x x - x - - - - - - - -
EW 15/2 85--------------
EW 35 8.5 5 8/5 - - - - x - - - - - - - -
EWK 8.5 58/5-------------
EWK 1 8.5 5 8/5 - - - - x - - - - - - - -
EWK 2 8.5 58/5-------------
IAK 1.5N 3L 55 10/52) 10/5 - - - - - - - - x - - -
IDK 1.5N 55 10/52) 10/5 - x3) ----------
IDK 1.5N/V 55 10/52) 10/5 - - - - - - - - x - - -
IDU 1.5 N ... 55 10/52) 10/5 - - - - - - - - x - - -
IDU 2.5N... 66 10/61) 12/6------------
IEK 1.5N... 55 10/52) 10/5 - - - - - - - - x - - -
IIK 1.5N... 55 10/52) 10/5 - - - - - - - - x - - -
IPE 1.5N... 55 10/52) 10/5 - - - - - - - - x - - -
IPE 2.5N... 66 10/61) 12/6------------
ITR 1.5N... 55 10/52) 10/5 - - - - - - - - x - - -
ITR 2.5N... 66 10/61) 12/6------------
PTR 2.5/... 55 10/5 10/5 - - - - - - - - - - - -
MAK 2.5/VLI 1.5... 66 8/5 - x x x - - - - - x - - -
WDK 1.5/R 3.5... 3.5 3.5--------------
WDK 2.5 ... 55 8/5 - - x - - - - - - x - - -
WDK 2.5 800V 66 8/5 - - x - - - - - - x - - -
WDK 2.5/BLA R5.08 5.08 5 8/5 - - - - x - - - - - - - -
WDK 2.5/BLZ R5.08 5.08 5 8/5 - - - - x - - - - - - - -
WDK 2.5N... 558/5-------------
WDK 4N... 558/5-------------
WDL 2.5/... 66 8/5 - - - - x - - - - x - - -
WDT 1.5 6.5 6.58/5-------------
WDTR 2.5... 6.2 68/5--x----------
WDU (WPE) 120/150 32 5 10/5 - - - - x - - - x - - - -
WDU (WPE) 35 N 16 5 12/5 - x x x x - - - - x - - -
WDU (WPE) 70/95 27 5 12/5 - - - - x - - - x - - - -
WDU (WPE) 70N 20.5 5 12/5 - x x x x - - - - x - - -
WDU 1.5 LD/BLA 5.08 5 12/5 - x x x x - - - - x - - -
WDU 1.5/BLA 5.08 5 12/5 - x x x x - - - - x - - -
WDU 1.5/BLZ R7.62 7.62 5----------x---
WDU 1.5/BLZ/5.08 5.08 5 12/5 - x x x x - - - - x - - -
WDU 1.5/BLZ/LD/5.08 5.08 5 12/5 - x x x x - - - - x - - -
WDU 1.5/R 3.5... 3.5 3.5--------------
WDU 1.5/R/BLA 5.08 5 12/5 - x x x x - - - - x - - -
WDU 1.5/ZZ 55 12/5 - x x x x - - - - x - - -
WDU 10 SL 10 5 12/5 - x x x x x x - - x - - -
WDU 10... 10 5 12/5 - x x x x x x - - x - - -
WDU 16 (/ZA) 12 5 12/5 - x x x x - - x - x - - -
WDU 16 N 12 5 12/5 - x x x x - - - - x - - -
WDU 2.5 F 55 12/5 - - - - x - - - - - - - -
WDU 2.5 FF 55 12/5 - x - - x - - - - - - - -
WDU 2.5 N (WDU 1.5) 55 12/5 - x x x x - - - - x - - -
WDU 2.5 TC... 55 12/5 - x x - x - - - - x - - -
WDU 2.5... 55 12/5 - x x x x x - - - x - - -
WDU 2.5/1.5/ZZ 55 12/5 - x x x x - - - - x - - -
WDU 2.5/BLZ R7.62 7.62 5----------x---
WDU 240... 36 512/5-------------
WDU 35 16 5 12/5 - x x x x - - x - x - - -
WDU 4 ... 66 12/6 - x x x x x - - - x - - -
WDU 4N ... 66 12/6 - x x x x - - - - x - - -
WDU 50N 18.5 512/5-------------
WDU 6 ... 88 12/8 - x x x x x x - - x - - -
WDU 95N 27 815/5-------------
WDUL 4 66 12/6 - x x x x x - - - x - - -
WEW 32/1 12.2 5 12/5 - x x x x - - - x x - - -
WEW 35/1 12.2 5 12/5 - x x x x - - - x x - - -
WEW 35/2 88 12/5 - x x x x - - x - - - - x
WF 10... 35.6 615/5-------------
WF 12... 35.6 615/5-------------
WF 5... 13 615/5-------------
WF 6... 19.6 615/5-------------
WF 8... 24.6 615/5-------------
WFF 120... 42 5 12/6.5 - - - - - - - - - - - - -
WFF 185... 55 5 12/6.5 - - - - - - - - - - - - -
WFF 300... 55 5 12/6.5 - - - - - - - - - - - - -
WFF 35... 27 512/5-------------
WFF 70... 32 5 12/6.5 - - - - - - - - - - - - -
WGK 8-25 5.6.8 10/5 10/5 - - - - - - - - - - - -
WMA 4... 66 12/6 - x x x x x - - - x - - -
WNT 10 10 5 12/5 - x x x x - - - - x - - -
WNT 16 N 12 5 12/5 - x x x x - - - - x - - -
WNT 2.5 55 12/5 - x x x x - - - - x - - -
1) = WS 10/6 Middle; 2) = WS 10/5 Middle; 3) = SnapMark
G.36
Accessories
G
Terminal markers – Selection table
Designation
Terminal
width
DEK
WS
ZS
SchT 7
SchT 9/4
SchT 14/6
WTS 3/4
WGB 5 /
WAD 5
WGB 8/
WAD 8
WAD 12
WAD 27
ZGB 15 /
ZGB 30
BZT 1
BZT 2
EM 8/30
WNT 35 N 16 5 12/5 - x x x x - - - - x - - -
WNT 4 66 12/6 - x x x x - - - - x - - -
WNT 6 88 12/5 - x x x x - - - - x - - -
WNT 70 N 20.5 5 12/5 - x x x x - - - - x - - -
WPE 1.5/R3.5 3.5 3.5 12/3.5 - - - - - - - - - - - - -
WPE 1.5/ZZ 55 12/5 - x x x x - - - - x - - -
WPE 10... 10 5 12/5 - x x x x - - - - x - - -
WPE 120 32 8 12/6.5 - - - - - - - - - - - - -
WPE 16 12 5 12/5 - x x x x - - - - x - - -
WPE 16 N 12 5 12/5 - x x x x - - - - x - - -
WPE 2.5 N (WPE 1.5) 55 12/5 - x x x x - - - - x - - -
WPE 2.5... 55 12/5 - x x x x - - - - x - - -
WPE 2.5/1.5/ZR 5512/5-------------
WPE 35... 16 5 12/5 - x x x x - - - - x - - -
WPE 4 66 12/6 - x x x x - - - - x - - -
WPE 4N 6612/6-------------
WPE 50N 18.5 8 12/6.5 - - - - - - - - - - - - -
WPE 6 88 12/5 - x x x x - - - - x - - -
WPE 95N/120N 27 815/5-------------
WPO 4 66 10/6 - - - - - - - - - x - - -
WSI 6... 88 12/5 - - - - x - - - - x - - -
WSI 6/2... 12 8 12/6.5 - - - - - - - - - - - - -
WTD 6/1 88 12/5 - - - - x - - - - x - - -
WTL 4 ... 6612/6-------------
WTL 6/1... 88 12/8 - - - - x - - - - x - - -
WTL 6/2 88 12/8 - - - - x - - - - x - - -
WTL 6/3... 88 12/8 - - - - x - - - - x - - -
WTQ 6/1 88 12/8 - - - - x - - - - x - - -
WTR 2.5 ... 55 12/5 - - - - x - - - - x - - -
WTR 4... 6612/6-------------
ZAP/TW ZIA 1.5/... 3.8 3.5--------------
ZDK 1.5... 3.5 3.5 12/3.5 - - - - - - - - - - - - -
ZDK 2.5... 55 12/5 15/5 - - - x - - - - x - - -
ZDK 2.5-2... 55 10/5 10/5 - - - - - - - - - - - -
ZDK 2.5/3AN 55 10/5 10/5 - - - - - - - - - - - -
ZDK 4/S/... 66 - 12/6 - - - x - - - - x - - -
ZDK 6/S/... 88 - - - - - x - - - - x - - -
ZDKPE 2.5 55 10/5 10/5 - - - - - - - - - - - -
ZDL 2.5/... 55 - 10/5 - - - - - - - - x - - -
ZDLD 2.5-2... 55 - 10/5 - - - - - - - - x - - -
ZDT 2.5 ... 55 10/5 10/5 - - - - - - - - - - - -
ZDTPE 2.5... 55 10/5 10/5 - - - - - - - - - - - -
ZDTR 2.5 55 12/5 15/5 - - - x - - - - x - - -
ZDU (ZPE) 10 10 5 12/5 15/5 - x - - - - - - x x x -
ZDU (ZPE) 10/S... 10 5 10/5 15/5 - x - - - - - - x x x -
ZDU (ZPE) 16... 12 5 12/5 15/5 - x - x - - - - x x x -
ZDU (ZPE) 16/S... 12 5 10/5 15/5 - x - - - - - - x x x -
ZDU (ZPE) 2.5N 55 10/5 10/5 - - - - - - - - - - - -
ZDU (ZPE) 2.5 ... 55 12/5 15/5 - - - x - - - - x x x -
ZDU (ZPE) 2.5-2/... 55 12/5 15/5 - - - x - - - - x - - -
ZDU (ZPE) 35... 16 5 12/5 15/5 - - - x - - - - x x x -
ZDU (ZPE) 4... 66 12/6 12/6 - - - x - - - - x x x -
ZDU (ZPE) 4-2... 66 12/6 12/6 - - - - - - - - - - - -
ZDU (ZPE) 6... 88 12/8 15/5 - - - x - - - - x x x -
ZDU (ZPE) 6-2... 88 12/8 12/6 - - - - - - - - - - - -
ZDU 1.5... 3.5 3.5 12/3.5 - - - - - - - - - - x x -
ZDUA (ZPEA) 2.5-2 55 8/5 15/5 - - - x - - - - x - - -
ZDUA 2.5-2N 55 10/5 10/5 - - - - - - - - - - - -
ZDUB (ZPEB) 2.5-2/... 55 8/5 15/5 - - - - - - - - x - - -
ZEI 16 16 5 12/5 15/5 - - - x - - - - x - - -
ZEI 6 10 8 12/6 12/6 - - - x - - - - x x x -
ZEW 35/2 88-------------x
ZIA 1.5 ... 5.08 5 8/5 15/5 - - - x - - - - x - - -
ZMAK 2.5 55 10/5 15/5 - - - - - - - - x - - -
ZNT 10/S 10 5--------------
ZNT 16/S 12 5--------------
ZNT 2.5/S 55 10/5 10/5 - - - - - - - - - - - -
ZNT 4/S 66 10/6 12/6 - - - - - - - - - - - -
ZNT 6/S 88 10/6 12/6 - - - - - - - - - - - -
ZP 2.5... 55 10/5 10/5 - -----------
ZPE 16-2/1 AN 12 8 12/6 12/6 - - - - - - - - - - - -
ZPV 1.5 5.08 5 12/5 15/5 - x x x - - - - x - - -
ZRV 1.5... 55 8/5 10/5 - x x x - - - - x - - -
ZSI 2.5... 88 12/5 15/5 - - - x - - - - x - - -
ZSI 2.5/2... 12 5 12/5 15/5 - - - x - - - - x - - -
ZSI 6-2/FC 86 12/6 12/6 - - - - - - - - - - - -
ZT 2.5 ... 55 10/5 10/5 - - - - - - - - - - - -
ZTD 6 88 12/6.5 - - - - - - - - - - - - -
ZTL 6 88 12/6.5 - - - - - - - - - - - - -
ZTPE 2.5 ... 55 10/5 10/5 - - - - - - - - - - - -
ZTR 2.5... 55 12/5 15/5 - - - x - - - - x - - -
ZTR 2.5-2... 55 14/5 10/5 - - - - - - - - - - - -
PDL 4... 5512/5-------------
PDU 2.5/4... 5512/5-------------
PDU 6/10... 8810/8-------------
G.37
Accessories
G
Terminal markers – Selection table
Designation
Terminal
width
DEK
WS
ZS
SchT 7
SchT 9/4
SchT 14/6
WTS 3/4
WGB 5 /
WAD 5
WGB 8/
WAD 8
WAD 12
WAD 27
ZGB 15 /
ZGB 30
BZT 1
BZT 2
EM 8/30
PDU 16 12 -10/12-------------
PDK 2.5/4 5512/5-------------
PPE 2.5/4 5512/5-------------
PPE 6/10 8810/8-------------
PPE 16 12 -10/12-------------
PNT 2.5/4 5512/5-------------
PNT 6/10 8810/8-------------
PNT 16 12 -10/12-------------
PEI 16 12 -10/12-------------
AST 1-4/35 6.2 6--------------
AST 5/35 6.5 6 ------------
DK 4… 66--------------
DKT 4… 66--------------
EK 10 10 5--------------
EK 16 12 5--------------
EK 2.5… 66--------------
EK 35… 16 5--------------
EK 4… 6.5 6.5--------------
EK 6/35 88--------------
KDKS 1… 88--------------
KSKM… 13 5--------------
KST… 24-34 5--------------
NT… 6-12 6 - - - - ----------
RSF 1-3… 85--------------
SAK 10… 10 5--------------
SAK 16… 12 5--------------
SAK 2.5 6.1 6--x-----------
SAK 2.5/35 55--x-----------
SAK 35… 18 5--x-----------
SAK 4… 6.5 6.5--x-----------
SAK 6… 88--x-----------
SAK 95/35 28 5--x-----------
SAKC 10/35 12 6.5--x-----------
SAKC 4/35 6.5 6.5--x-----------
SAKG… 32-54 5--x-----------
SAKR… 6.5 6.5--x-----------
SAKS…. 13-28 5--x-----------
SAKT… 86.5--x-----------
SAKD 2.5N 55--x-----------
SAKA 10 12 5--x-----------
SAKB 10 10 5--x-----------
ASK 1 88--x-----------
SAKK 4.. 86.5--x-----------
SAKK 10.. 11.5 5--x-----------
SAKH 4-10 6.5-14 5--x-----------
SAKH 35 18 6.5--------------
KMVF… 65--------------
AKZ 1.5-2.5 5.1 5--------------
AKZ 4 6.1 6--------------
AKE 2.5 5.1 5--------------
AKE 4 76.5--------------
ADK 1 66--------------
AL 1 6.5 6.5--------------
AKA 4 66--------------
G.38
Accessories
G
Terminal markers – DEK standard printing
The Dekafix marker is the universal marker for terminals and
plug-in connectors as well as electronic modules from the
Weidmüller product range. Dekafix provides you with a wide
range of standard printing options. The system is particularly
suitable for short sequences of numbers and is also available
with customer specific printing.
•Instripsforfastinstallation
•Largeselectionofready-to-useprintedmarkers
•ExcellentprintingqualitythankstotheMCLaser
•Availablein4widths
•Customprintingalsopossible
DEK card with printing
Technical data
Material Polyamide 66, halogen-free
UL 94 flammability rating V2
Temperature range –40 °C to 100 °C
Printing black
Ordering data
Colour Available in all colours of the international colour code; for MC
on request
● brown ● red ● orange
● yellow ● green ● blue
● violet ● grey white
Qty 500 pcs
Pitch DEK 5 = 5 mm : DEK 6 = 6 mm : DEK 6.5 = 6.5 mm :
DEK 8 = 8 mm
Printing variations FZ = consecutive horizontal e.g. DEK 5 FW 1-50
FS = consecutive vertical e.g. DEK 5 FS 51-100
FWZ = consecutive horizontal line e.g. DEK 5 FWZ 1-10
FSZ = consecutive vertical line e.g. DEK 5 FSZ 21-30
GW = identical horizontal e.g. DEK 5 GW A
GS = identical vertical e.g. DEK 5 GS B
No. of characters horizontal vertical
Dek 5 max. 3 characters max. 3 characters
Dek 6 max. 3 characters max. 3 characters
Dek 6,5 max. 4 characters max. 3 characters
Dek 8 max. 5 characters max. 3 characters
Specify colour and characters for special printing
GW
Blank
FWZ
FS
G.39
Accessories
G
Terminal markers – DEK standard printing
Type/Print Order No.
DEK 5 BL NEUTRAL 0473391693
DEK 5 BR NEUTRAL 0473391692
DEK 5 FS 1-50 0473560001
DEK 5 FS 101-150 0473560101
DEK 5 FS 151-200 0473560151
DEK 5 FS 201-250 0473560201
DEK 5 FS 251-300 0473560251
DEK 5 FS 301-350 0473560301
DEK 5 FS 351-400 0473560351
DEK 5 FS 401-450 0473560401
DEK 5 FS 451-500 0473560451
DEK 5 FS 501-550 0473560501
DEK 5 FS 51-100 0473560051
DEK 5 FS 551-600 0473560551
DEK 5 FS 601-650 0473560601
DEK 5 FS 651-700 0473560651
DEK 5 FS 701-750 0473560701
DEK 5 FS 751-800 0473560751
DEK 5 FS 801-850 0473560801
DEK 5 FS 851-900 0473560851
DEK 5 FS 901-950 0473560901
DEK 5 FS 951-999 0473560951
DEK 5 FSZ 1-10 0460660001
DEK 5 FSZ 11-20 0460660011
DEK 5 FSZ 18,20,...32 0582360018
DEK 5 FSZ 2,4,6...16 0582360002
DEK 5 FSZ 21-30 0460660021
DEK 5 FSZ 31-40 0460660031
DEK 5 FSZ 41-50 0460660041
DEK 5 FSZ 51-60 0460660051
DEK 5 FSZ 61-70 0460660061
DEK 5 FSZ 71-80 0460660071
DEK 5 FSZ 81-90 0460660081
DEK 5 FSZ 91-100 0460660091
DEK 5 FW 1,3,5,...99 1358460000
DEK 5 FW 1-50 0473460001
DEK 5 FW 10-500 0132660010
DEK 5 FW 101-150 0473460101
DEK 5 FW 151-200 0473460151
DEK 5 FW 2,4,...100 1358560000
DEK 5 FW 201-250 0473460201
DEK 5 FW 251-300 0473460251
DEK 5 FW 301-350 0473460301
DEK 5 FW 351-400 0473460351
DEK 5 FW 401-450 0473460401
DEK 5 FW 451-500 0473460451
DEK 5 FW 501-550 0473460501
DEK 5 FW 51-100 0473460051
DEK 5 FW 551-600 0473460551
DEK 5 FW 601-650 0473460601
DEK 5 FW 651-700 0473460651
DEK 5 FW 701-750 0473460701
DEK 5 FW 751-800 0473460751
DEK 5 FW 801-850 0473460801
DEK 5 FW 851-900 0473460851
DEK 5 FW 901-950 0473460901
DEK 5 FW 951-999 0473460951
DEK 5 FW U1-PE1 0133161114
DEK 5 FW U2-PE2 0133161115
DEK 5 FW U3-PE3 0133161116
DEK 5 FW U4-PE4 0133161117
DEK 5 FW U5-PE5 0133161118
DEK 5 FW U6-PE6 0133161119
DEK 5 FW U7-PE7 0133161120
DEK 5 FW U8-PE8 0133161121
DEK 5 FW U9-PE9 0133161122
DEK 5 FW X1-Z1 0133261150
DEK 5 FW X10-Z10 0133261159
DEK 5 FW X2-Z2 0133261151
DEK 5 FW X3-Z3 0133261152
DEK 5 FW X4-Z4 0133261153
DEK 5 FW X5-Z5 0133261154
Type/Print Order No.
DEK 5 FW X6-Z6 0133261155
DEK 5 FW X7-Z7 0133261156
DEK 5 FW X8-Z8 0133261157
DEK 5 FW X9-Z9 0133261158
DEK 5 FWZ 1-10 0523060001
DEK 5 FWZ 1-19 0235860000
DEK 5 FWZ 1-9 1572000000
DEK 5 FWZ 11-20 0523060011
DEK 5 FWZ 2-20 0236160000
DEK 5 FWZ 21-30 0523060021
DEK 5 FWZ 21-39 0235960000
DEK 5 FWZ 22-40 0236260000
DEK 5 FWZ 31-40 0523060031
DEK 5 FWZ 41-50 0523060041
DEK 5 FWZ 41-59 0236060000
DEK 5 FWZ 42-60 0236360000
DEK 5 FWZ 51-60 0523060051
DEK 5 FWZ 61-70 0523060061
DEK 5 FWZ 71-80 0523060071
DEK 5 FWZ 81-90 0523060081
DEK 5 FWZ 91-100 0523060091
DEK 5 FWZ L1-EIK 0354361203
DEK 5 FWZ L1-PE 0354361187
DEK 5 FWZ U,V,W,N,PE 0558360000
DEK 5 GE NEUTRAL 0473391687
DEK 5 GN NEUTRAL 0473391688
DEK 5 GR NEUTRAL 0473391691
DEK 5 GS A 0132961021
DEK 5 GS B 0132961022
DEK 5 GS C 0132961023
DEK 5 GS D 0132961024
DEK 5 GS E 0132961025
DEK 5 GS F 0132961026
DEK 5 GS G 0132961027
DEK 5 GS H 0132961028
DEK 5 GS I 0132961029
DEK 5 GS J 0132961030
DEK 5 GS K 0132961031
DEK 5 GS L 0132961032
DEK 5 GS M 0132961033
DEK 5 GS N 0132961034
DEK 5 GS O 0132961035
DEK 5 GS P 0132961036
DEK 5 GS PE 0157261187
DEK 5 GS Q 0132961037
DEK 5 GS R 0132961038
DEK 5 GS S 0132961039
DEK 5 GS T 0132961040
DEK 5 GS U 0132961041
DEK 5 GS V 0132961042
DEK 5 GS W 0132961043
DEK 5 GS X 0132961044
DEK 5 GS Y 0132961045
DEK 5 GS Z 0132961046
DEK 5 GS g 0157261202
DEK 5 GS h0157261203
DEK 5 GW 0576260000
DEK 5 GW 1 0522660001
DEK 5 GW 2 0522660002
DEK 5 GW 3 0522660003
DEK 5 GW 4 0522660004
DEK 5 GW 5 0522660005
DEK 5 GW 6 0522660006
DEK 5 GW 7 0522660007
DEK 5 GW 8 0522660008
DEK 5 GW 9 0522660009
DEK 5 GW 10 0522660010
DEK 5 GW 11 0522660011
DEK 5 GW 12 0522660012
DEK 5 GW 13 0522660013
DEK 5 GW 14 0522660014
DEK 5 GW 15 0522660015
Type/Print Order No.
DEK 5 GW 16 0522660016
DEK 5 GW 17 0522660017
DEK 5 GW 18 0522660018
DEK 5 GW 19 0522660019
DEK 5 GW 20 0522660020
DEK 5 GW 21 0522660021
DEK 5 GW 22 0522660022
DEK 5 GW 23 0522660023
DEK 5 GW 24 0522660024
DEK 5 GW 25 0522660025
DEK 5 GW 26 0522660026
DEK 5 GW 27 0522660027
DEK 5 GW 28 0522660028
DEK 5 GW 29 0522660029
DEK 5 GW 30 0522660030
DEK 5 GW 31 0522660031
DEK 5 GW 32 0522660032
DEK 5 GW 33 0522660033
DEK 5 GW 34 0522660034
DEK 5 GW 35 0522660035
DEK 5 GW 36 0522660036
DEK 5 GW 37 0522660037
DEK 5 GW 38 0522660038
DEK 5 GW 39 0522660039
DEK 5 GW 40 0522660040
DEK 5 GW 41 0522660041
DEK 5 GW 42 0522660042
DEK 5 GW 43 0522660043
DEK 5 GW 44 0522660044
DEK 5 GW 45 0522660045
DEK 5 GW 46 0522660046
DEK 5 GW 47 0522660047
DEK 5 GW 48 0522660048
DEK 5 GW 49 0522660049
DEK 5 GW 50 0522660050
DEK 5 GW 51 0522660051
DEK 5 GW 52 0522660052
DEK 5 GW 53 0522660053
DEK 5 GW 54 0522660054
DEK 5 GW 55 0522660055
DEK 5 GW 56 0522660056
DEK 5 GW 57 0522660057
DEK 5 GW 58 0522660058
DEK 5 GW 59 0522660059
DEK 5 GW 60 0522660060
DEK 5 GW 61 0522660061
DEK 5 GW 62 0522660062
DEK 5 GW 63 0522660063
DEK 5 GW 64 0522660064
DEK 5 GW 65 0522660065
DEK 5 GW 66 0522660066
DEK 5 GW 67 0522660067
DEK 5 GW 68 0522660068
DEK 5 GW 69 0522660069
DEK 5 GW 70 0522660070
DEK 5 GW 71 0522660071
DEK 5 GW 72 0522660072
DEK 5 GW 73 0522660073
DEK 5 GW 74 0522660074
DEK 5 GW 75 0522660075
DEK 5 GW 76 0522660076
DEK 5 GW 77 0522660077
DEK 5 GW 78 0522660078
DEK 5 GW 79 0522660079
DEK 5 GW 80 0522660080
DEK 5 GW 81 0522660081
DEK 5 GW 82 0522660082
DEK 5 GW 83 0522660083
DEK 5 GW 84 0522660084
DEK 5 GW 85 0522660085
DEK 5 GW 86 0522660086
DEK 5 GW 87 0522660087
Type/Print Order No.
DEK 5 GW 88 0522660088
DEK 5 GW 89 0522660089
DEK 5 GW 90 0522660090
DEK 5 GW 91 0522660091
DEK 5 GW 92 0522660092
DEK 5 GW 93 0522660093
DEK 5 GW 94 0522660094
DEK 5 GW 95 0522660095
DEK 5 GW 96 0522660096
DEK 5 GW 97 0522660097
DEK 5 GW 98 0522660098
DEK 5 GW 99 0522660099
DEK 5 GW 100 0522660100
DEK 5 GW 101 0522660101
DEK 5 GW 102 0522660102
DEK 5 GW 103 0522660103
DEK 5 GW 104 0522660104
DEK 5 GW 105 0522660105
DEK 5 GW 106 0522660106
DEK 5 GW 107 0522660107
DEK 5 GW 108 0522660108
DEK 5 GW 109 0522660109
DEK 5 GW 110 0522660110
DEK 5 GW 111 0522660111
DEK 5 GW 112 0522660112
DEK 5 GW 113 0522660113
DEK 5 GW 114 0522660114
DEK 5 GW 115 0522660115
DEK 5 GW 116 0522660116
DEK 5 GW 117 0522660117
DEK 5 GW 118 0522660118
DEK 5 GW 119 0522660119
DEK 5 GW 120 0522660120
DEK 5 GW 121 0522660121
DEK 5 GW 122 0522660122
DEK 5 GW 123 0522660123
DEK 5 GW 124 0522660124
DEK 5 GW 125 0522660125
DEK 5 GW 126 0522660126
DEK 5 GW 127 0522660127
DEK 5 GW 128 0522660128
DEK 5 GW 129 0522660129
DEK 5 GW 130 0522660130
DEK 5 GW 131 0522660131
DEK 5 GW 132 0522660132
DEK 5 GW 133 0522660133
DEK 5 GW 134 0522660134
DEK 5 GW 135 0522660135
DEK 5 GW 136 0522660136
DEK 5 GW 137 0522660137
DEK 5 GW 138 0522660138
DEK 5 GW 139 0522660139
DEK 5 GW 140 0522660140
DEK 5 GW 141 0522660141
DEK 5 GW 142 0522660142
DEK 5 GW 143 0522660143
DEK 5 GW 144 0522660144
DEK 5 GW 145 0522660145
DEK 5 GW 146 0522660146
DEK 5 GW 147 0522660147
DEK 5 GW 148 0522660148
DEK 5 GW 149 0522660149
DEK 5 GW 150 0522660150
DEK 5 GW 151 0522660151
DEK 5 GW 152 0522660152
DEK 5 GW 153 0522660153
DEK 5 GW 154 0522660154
DEK 5 GW 155 0522660155
DEK 5 GW 156 0522660156
DEK 5 GW 157 0522660157
DEK 5 GW 158 0522660158
DEK 5 GW 159 0522660159
Versions DEK
G.40
Accessories
G
Terminal markers – DEK standard printing
Type/Print Order No.
DEK 5 GW 160 0522660160
DEK 5 GW 161 0522660161
DEK 5 GW 162 0522660162
DEK 5 GW 163 0522660163
DEK 5 GW 164 0522660164
DEK 5 GW 165 0522660165
DEK 5 GW 166 0522660166
DEK 5 GW 167 0522660167
DEK 5 GW 168 0522660168
DEK 5 GW 169 0522660169
DEK 5 GW 170 0522660170
DEK 5 GW 171 0522660171
DEK 5 GW 172 0522660172
DEK 5 GW 173 0522660173
DEK 5 GW 174 0522660174
DEK 5 GW 175 0522660175
DEK 5 GW 176 0522660176
DEK 5 GW 177 0522660177
DEK 5 GW 178 0522660178
DEK 5 GW 179 0522660179
DEK 5 GW 180 0522660180
DEK 5 GW 181 0522660181
DEK 5 GW 182 0522660182
DEK 5 GW 183 0522660183
DEK 5 GW 184 0522660184
DEK 5 GW 185 0522660185
DEK 5 GW 186 0522660186
DEK 5 GW 187 0522660187
DEK 5 GW 188 0522660188
DEK 5 GW 189 0522660189
DEK 5 GW 190 0522660190
DEK 5 GW 191 0522660191
DEK 5 GW 192 0522660192
DEK 5 GW 193 0522660193
DEK 5 GW 194 0522660194
DEK 5 GW 195 0522660195
DEK 5 GW 196 0522660196
DEK 5 GW 197 0522660197
DEK 5 GW 198 0522660198
DEK 5 GW 199 0522660199
DEK 5 GW 200 0522660200
DEK 5 GW A 0522761021
DEK 5 GW a 0522861047
DEK 5 GW B 0522761022
DEK 5 GW b 0522861048
DEK 5 GW BL/SW - 0576291741
DEK 5 GW C 0522761023
DEK 5 GW c 0522861049
DEK 5 GW D 0522761024
DEK 5 GW d 0522861050
DEK 5 GW E 0522761025
DEK 5 GW e 0522861051
DEK 5 GW F 0522761026
DEK 5 GW f 0522861052
DEK 5 GW G 0522761027
DEK 5 GW g 0522861053
DEK 5 GW H 0522761028
DEK 5 GW h 0522861054
DEK 5 GW I 0522761029
DEK 5 GW i 0522861055
DEK 5 GW J 0522761030
DEK 5 GW j 0522861056
DEK 5 GW K 0522761031
DEK 5 GW k 0522861057
DEK 5 GW L 0522761032
DEK 5 GW l 0522861058
DEK 5 GW L1 0522361075
DEK 5 GW L2 0522361076
DEK 5 GW L3 0522361077
DEK 5 GW M 0522761033
DEK 5 GW m 0522861059
DEK 5 GW MP 0537261235
Type/Print Order No.
DEK 5 GW N 0522761034
DEK 5 GW n 0522861060
DEK 5 GW O 0522761035
DEK 5 GW o 0522861061
DEK 5 GW P 0522761036
DEK 5 GW p 0522861062
DEK 5 GW PE 0537261187
DEK 5 GW PEN 0537261188
DEK 5 GW Q 0522761037
DEK 5 GW q 0522861063
DEK 5 GW R 0522761038
DEK 5 GW r 0522861064
DEK 5 GW RT/SW + 0576291737
DEK 5 GW S 0522761039
DEK 5 GW s 0522861065
DEK 5 GW T 0522761040
DEK 5 GW t 0522861066
DEK 5 GW U 0522761041
DEK 5 GW u 0522861067
DEK 5 GW V 0522761042
DEK 5 GW v 0522861068
DEK 5 GW W 0522761043
DEK 5 GW w 0522861069
DEK 5 GW W-STROM 0576261215
DEK 5 GW X 0522761044
DEK 5 GW x 0522861070
DEK 5 GW Y 0522761045
DEK 5 GW y 0522861071
DEK 5 GW Z 0522761046
DEK 5 GW z 0522861072
DEK 5 GW + 0576261198
DEK 5 GW - 0576261199
DEK 5 GW g 0576261202
DEK 5 GW h 0576261203
DEK 5 NEUTRAL 0473360000
DEK 5 OR NEUTRAL 0473391690
DEK 5 RT NEUTRAL 0473391686
DEK 5 SW NEUTRAL 0473391694
DEK 5 VI NEUTRAL 0473391689
DEK 5/3,5 MC FS 1-10 1762320001
DEK 5/3,5 MC FS 101-110 1762320101
DEK 5/3,5 MC FS 11-20 1762320011
DEK 5/3,5 MC FS 111-120 1762320111
DEK 5/3,5 MC FS 121-130 1762320121
DEK 5/3,5 MC FS 131-140 1762320131
DEK 5/3,5 MC FS 141-150 1762320141
DEK 5/3,5 MC FS 21-30 1762320021
DEK 5/3,5 MC FS 31-40 1762320031
DEK 5/3,5 MC FS 41-50 1762320041
DEK 5/3,5 MC FS 51-60 1762320051
DEK 5/3,5 MC FS 61-70 1762320061
DEK 5/3,5 MC FS 71-80 1762320071
DEK 5/3,5 MC FS 81-90 1762320081
DEK 5/3,5 MC FS 91-100 1762320091
DEK 5/3,5 MC GW 0 1755281000
DEK 5/3,5 MC GW 1 1755280001
DEK 5/3,5 MC GW 2 1755280002
DEK 5/3,5 MC GW 3 1755280003
DEK 5/3,5 MC GW 4 1755280004
DEK 5/3,5 MC GW 5 1755280005
DEK 5/3,5 MC GW 6 1755280006
DEK 5/3,5 MC GW 7 1755280007
DEK 5/3,5 MC GW 8 1755280008
DEK 5/3,5 MC GW 9 1755280009
DEK 6 NEUTRAL 0468560000
DEK 6 BL NEUTRAL 0468591693
DEK 6 BR NEUTRAL 0468591692
DEK 6 FS 1-50 0468760001
DEK 6 FS 101-150 0468760101
DEK 6 FS 151-200 0468760151
Type/Print Order No.
DEK 6 FS 201-250 0468760201
DEK 6 FS 251-300 0468760251
DEK 6 FS 301-350 0468760301
DEK 6 FS 351-400 0468760351
DEK 6 FS 401-450 0468760401
DEK 6 FS 451-500 0468760451
DEK 6 FS 501-550 0468760501
DEK 6 FS 51-100 0468760051
DEK 6 FS 551-600 0468760551
DEK 6 FS 601-650 0468760601
DEK 6 FS 651-700 0468760651
DEK 6 FS 701-750 0468760701
DEK 6 FS 751-800 0468760751
DEK 6 FS 801-850 0468760801
DEK 6 FS 851-900 0468760851
DEK 6 FS 901-950 0468760901
DEK 6 FS 951-999 0468760951
DEK 6 FSZ 1-10 0133360001
DEK 6 FSZ 11-20 0133360011
DEK 6 FSZ 21-30 0133360021
DEK 6 FSZ 31-40 0133360031
DEK 6 FSZ 41-50 0133360041
DEK 6 FSZ 51-60 0133360051
DEK 6 FSZ 61-70 0133360061
DEK 6 FSZ 71-80 0133360071
DEK 6 FSZ 81-90 0133360081
DEK 6 FSZ 91-100 0133360091
DEK 6 FW 1,3,5...99 1358660000
DEK 6 FW 1-5 (10X) 0688660000
DEK 6 FW 1-50 0468660001
DEK 6 FW 101-150 0468660101
DEK 6 FW 151-200 0468660151
DEK 6 FW 2,4,...100 1358760000
DEK 6 FW 201-250 0468660201
DEK 6 FW 251-300 0468660251
DEK 6 FW 301-350 0468660301
DEK 6 FW 351-400 0468660351
DEK 6 FW 401-450 0468660401
DEK 6 FW 451-500 0468660451
DEK 6 FW 501-550 0468660501
DEK 6 FW 51-100 0468660051
DEK 6 FW 551-600 0468660551
DEK 6 FW 601-650 0468660601
DEK 6 FW 651-700 0468660651
DEK 6 FW 701-750 0468660701
DEK 6 FW 751-800 0468660751
DEK 6 FW 801-850 0468660801
DEK 6 FW 851-900 0468660851
DEK 6 FW 901-950 0468660901
DEK 6 FW 951-999 0468660951
DEK 6 FW L,N,PE 0632560000
DEK 6 FWZ 1-10 0518960001
DEK 6 FWZ 101-110 0518960101
DEK 6 FWZ 11-20 0518960011
DEK 6 FWZ 111-120 0518960111
DEK 6 FWZ 121-130 0518960121
DEK 6 FWZ 131-140 0518960131
DEK 6 FWZ 141-150 0518960141
DEK 6 FWZ 151-160 0518960151
DEK 6 FWZ 161-170 0518960161
DEK 6 FWZ 171-180 0518960171
DEK 6 FWZ 181-190 0518960181
DEK 6 FWZ 191-200 0518960191
DEK 6 FWZ 201-210 0518960201
DEK 6 FWZ 21-30 0518960021
DEK 6 FWZ 31-40 0518960031
DEK 6 FWZ 41-50 0518960041
DEK 6 FWZ 51-60 0518960051
DEK 6 FWZ 61-70 0518960061
DEK 6 FWZ 71-80 0518960071
DEK 6 FWZ 81-90 0518960081
DEK 6 FWZ 91-100 0518960091
Type/Print Order No.
DEK 6 FWZ L1-h 0631961203
DEK 6 FWZ L1-PE 0631961187
DEK 6 FWZ R,S,T,N,g0631860000
DEK 6 GE NEUTRAL 0468591687
DEK 6 GN NEUTRAL 0468591688
DEK 6 GR NEUTRAL 0468591691
DEK 6 GW 0 0526961000
DEK 6 GW 1 0526960001
DEK 6 GW 2 0526960002
DEK 6 GW 3 0526960003
DEK 6 GW 4 0526960004
DEK 6 GW 5 0526960005
DEK 6 GW 6 0526960006
DEK 6 GW 7 0526960007
DEK 6 GW 8 0526960008
DEK 6 GW 9 0526960009
DEK 6 GW 10 0526960010
DEK 6 GW 11 0526960011
DEK 6 GW 12 0526960012
DEK 6 GW 13 0526960013
DEK 6 GW 14 0526960014
DEK 6 GW 15 0526960015
DEK 6 GW 16 0526960016
DEK 6 GW 17 0526960017
DEK 6 GW 18 0526960018
DEK 6 GW 19 0526960019
DEK 6 GW 20 0526960020
DEK 6 GW 21 0526960021
DEK 6 GW 22 0526960022
DEK 6 GW 23 0526960023
DEK 6 GW 24 0526960024
DEK 6 GW 25 0526960025
DEK 6 GW 26 0526960026
DEK 6 GW 27 0526960027
DEK 6 GW 28 0526960028
DEK 6 GW 29 0526960029
DEK 6 GW 30 0526960030
DEK 6 GW 31 0526960031
DEK 6 GW 32 0526960032
DEK 6 GW 33 0526960033
DEK 6 GW 34 0526960034
DEK 6 GW 35 0526960035
DEK 6 GW 36 0526960036
DEK 6 GW 37 0526960037
DEK 6 GW 38 0526960038
DEK 6 GW 39 0526960039
DEK 6 GW 40 0526960040
DEK 6 GW 41 0526960041
DEK 6 GW 42 0526960042
DEK 6 GW 43 0526960043
DEK 6 GW 44 0526960044
DEK 6 GW 45 0526960045
DEK 6 GW 46 0526960046
DEK 6 GW 47 0526960047
DEK 6 GW 48 0526960048
DEK 6 GW 49 0526960049
DEK 6 GW 50 0526960050
DEK 6 GW 51 0526960051
DEK 6 GW 52 0526960052
DEK 6 GW 53 0526960053
DEK 6 GW 54 0526960054
DEK 6 GW 55 0526960055
DEK 6 GW 56 0526960056
DEK 6 GW 57 0526960057
DEK 6 GW 58 0526960058
DEK 6 GW 59 0526960059
DEK 6 GW 60 0526960060
DEK 6 GW 61 0526960061
DEK 6 GW 62 0526960062
DEK 6 GW 63 0526960063
DEK 6 GW 64 0526960064
DEK 6 GW 65 0526960065
Versions DEK
G.41
Accessories
G
Terminal markers – DEK standard printing
Type/Print Order No.
DEK 6 GW 66 0526960066
DEK 6 GW 67 0526960067
DEK 6 GW 68 0526960068
DEK 6 GW 69 0526960069
DEK 6 GW 70 0526960070
DEK 6 GW 71 0526960071
DEK 6 GW 72 0526960072
DEK 6 GW 73 0526960073
DEK 6 GW 74 0526960074
DEK 6 GW 75 0526960075
DEK 6 GW 76 0526960076
DEK 6 GW 77 0526960077
DEK 6 GW 78 0526960078
DEK 6 GW 79 0526960079
DEK 6 GW 80 0526960080
DEK 6 GW 81 0526960081
DEK 6 GW 82 0526960082
DEK 6 GW 83 0526960083
DEK 6 GW 84 0526960084
DEK 6 GW 85 0526960085
DEK 6 GW 86 0526960086
DEK 6 GW 87 0526960087
DEK 6 GW 88 0526960088
DEK 6 GW 89 0526960089
DEK 6 GW 90 0526960090
DEK 6 GW 91 0526960091
DEK 6 GW 92 0526960092
DEK 6 GW 93 0526960093
DEK 6 GW 94 0526960094
DEK 6 GW 95 0526960095
DEK 6 GW 96 0526960096
DEK 6 GW 97 0526960097
DEK 6 GW 98 0526960098
DEK 6 GW 99 0526960099
DEK 6 GW 100 0526960100
DEK 6 GW 200 0526960200
DEK 6 GW BL/SW - 1318091741
DEK 6 GW PE 1318061187
DEK 6 GW RT/SW + 1318091737
DEK 6 GW + 1318061198
DEK 6 GW - 1318061199
DEK 6 GW g 1318061202
DEK 6 GW h 1318061203
DEK 6 NEUTRAL 0468560000
DEK 6 OR NEUTRAL 0468591690
DEK 6 RT NEUTRAL 0468591686
DEK 6 SW NEUTRAL 0468591694
DEK 6 VI NEUTRAL 0468591689
DEK 6,5 BL NEUTRAL 0468091693
DEK 6,5 FS 1-50 0468260001
DEK 6,5 FS 101-150 0468260101
DEK 6,5 FS 151-200 0468260151
DEK 6,5 FS 201-250 0468260201
DEK 6,5 FS 251-300 0468260251
DEK 6,5 FS 301-350 0468260301
DEK 6,5 FS 351-400 0468260351
DEK 6,5 FS 401-450 0468260401
DEK 6,5 FS 451-500 0468260451
DEK 6,5 FS 501-550 0468260501
DEK 6,5 FS 51-100 0468260051
DEK 6,5 FS 551-600 0468260551
DEK 6,5 FS 601-650 0468260601
DEK 6,5 FS 651-700 0468260651
DEK 6,5 FS 701-750 0468260701
DEK 6,5 FS 751-800 0468260751
DEK 6,5 FS 801-850 0468260801
DEK 6,5 FS 851-900 0468260851
DEK 6,5 FS 901-950 0468260901
DEK 6,5 FS 951-999 0468260951
DEK 6,5 FSZ 1-10 0407360001
DEK 6,5 FSZ 11-20 0407360011
Type/Print Order No.
DEK 6,5 FSZ 21-30 0407360021
DEK 6,5 FSZ 31-40 0407360031
DEK 6,5 FSZ 41-50 0407360041
DEK 6,5 FSZ 51-60 0407360051
DEK 6,5 FSZ 61-70 0407360061
DEK 6,5 FSZ 71-80 0407360071
DEK 6,5 FSZ 81-90 0407360081
DEK 6,5 FSZ 91-100 0407360091
DEK 6,5 FW 1-50 0468160001
DEK 6,5 FW 101-150 0468160101
DEK 6,5 FW 151-200 0468160151
DEK 6,5 FW 201-250 0468160201
DEK 6,5 FW 251-300 0468160251
DEK 6,5 FW 301-350 0468160301
DEK 6,5 FW 351-400 0468160351
DEK 6,5 FW 401-450 0468160401
DEK 6,5 FW 451-500 0468160451
DEK 6,5 FW 501-550 0468160501
DEK 6,5 FW 51-100 0468160051
DEK 6,5 FW 551-600 0468160551
DEK 6,5 FW 601-650 0468160601
DEK 6,5 FW 651-700 0468160651
DEK 6,5 FW 701-750 0468160701
DEK 6,5 FW 751-800 0468160751
DEK 6,5 FW 801-850 0468160801
DEK 6,5 FW 851-900 0468160851
DEK 6,5 FW 901-950 0468160901
DEK 6,5 FW 951-999 0468160951
DEK 6,5 FW L1- h0632161203
DEK 6,5 FW L1-PE 0632161187
DEK 6,5 FWZ 1-10 0519060001
DEK 6,5 FWZ 11-20 0519060011
DEK 6,5 FWZ 21-30 0519060021
DEK 6,5 FWZ 31-40 0519060031
DEK 6,5 FWZ 41-50 0519060041
DEK 6,5 FWZ 51-60 0519060051
DEK 6,5 FWZ 61-70 0519060061
DEK 6,5 FWZ 71-80 0519060071
DEK 6,5 FWZ 81-90 0519060081
DEK 6,5 FWZ 91-100 0519060091
DEK 6,5 FWZ R,S,T,N,ERD 0632060000
DEK 6,5 GE NEUTRAL 0468091687
DEK 6,5 GN NEUTRAL 0468091688
DEK 6,5 NEUTRAL 0468060000
DEK 6,5 OR NEUTRAL 0468091690
DEK 6,5 RT NEUTRAL 0468091686
DEK 6,5 SW NEUTRAL 0468091694
DEK 6,5 VI NEUTRAL 0468091689
DEK 8 BEDR./FARBIG 1289690000
DEK 8 FS 1-50 TAMPOPR. 1653350001
DEK 8 FS 1-50 TAMPOPR. 1653350001
DEK 8 FS 51-100 TAMPOP. 1653350051
DEK 8 FS 51-100 TAMPOP. 1653350051
DEK 8 FSZ 1-10 1289660001
DEK 8 FSZ 11-20 1289660011
DEK 8 FSZ 21-30 1289660021
DEK 8 FSZ 31-40 1289660031
DEK 8 FSZ 41-50 1289660041
DEK 8 FSZ 51-60 1289660051
DEK 8 FSZ 61-70 1289660061
DEK 8 FSZ 71-80 1289660071
DEK 8 FSZ 81-90 1289660081
DEK 8 FSZ 91-100 1289660091
DEK 8 FW 1-50 TAMPOPR. 1653340001
DEK 8 FW 1-50 TAMPOPR. 1653340001
DEK 8 FW 51-100 TAMPOP. 1653340051
DEK 8 FW 51-100 TAMPOP. 1653340051
DEK 8 FWZ 1-10 1276960001
DEK 8 FWZ 101-110 1276960101
DEK 8 FWZ 11-20 1276960011
DEK 8 FWZ 111-120 1276960111
Type/Print Order No.
DEK 8 FWZ 121-130 1276960121
DEK 8 FWZ 131-140 1276960131
DEK 8 FWZ 141-150 1276960141
DEK 8 FWZ 21-30 1276960021
DEK 8 FWZ 31-40 1276960031
DEK 8 FWZ 41-50 1276960041
DEK 8 FWZ 51-60 1276960051
DEK 8 FWZ 61-70 1276960061
DEK 8 FWZ 71-80 1276960071
DEK 8 FWZ 81-90 1276960081
DEK 8 FWZ 91-100 1276960091
DEK 8 GE NEUTRAL 1277091687
DEK 8 GN NEUTRAL 1277091688
DEK 8 NEUTRAL 1277060000
DEK 8 OR NEUTRAL 1277091690
DEK 8 RT NEUTRAL 1277091686
DEK 8 SONDERDR. FARBIG 1326690000
DEK 8 SONDERDR. WEIß 1326660000
DEK 8 VI NEUTRAL 1277091689
WS 8/5 Karte 1773360000
WS 10/5 Karte 1773370000
WS 12/5 Karte 1773380000
WS 12/5 FSZ 1 - 10 1773430001
WS 12/5 FSZ 11 - 20 1773430011
WS 12/5 FSZ 21 - 30 1773430021
WS 12/5 FSZ 31 - 40 1773430031
WS 12/5 FSZ 41 - 50 1773430041
WS 12/5 FWZ 1 - 10 1773330001
WS 12/5 FWZ 11 - 20 1773330011
WS 12/5 FWZ 21 - 30 1773330021
WS 12/5 FWZ 31 - 40 1773330031
WS 12/5 FWZ 41 - 50 1773330041
Versions DEK
G.42
Accessories
G
Terminal markers – Dekafix
The Dekafix marker in MultiCard format is the universal marker
for all kinds of connectors and also electronic modules from
the Weidmüller product range. The blank DEK marker is ideal
for flexible, fast printing in situ with our innovative labelling
systems SMark-Laser, PrintJet, MCP Plus Plotter or MC-
Mobilo. The system is particularly suitable for short sequences
of numbers and is also available with special printing.
• Instripsforfastinstallation
• Flexible,fastprintingonsiteduringinstallation
• ExcellentprintingqualitythankstotheWeidmüllerMultiCard
printers
• Availablein6widths
• CustomprintingwiththeMCLaseralsopossible
DEK MultiCard
Halogen
Technical data
Material Polyamide66,halogen-free
UL 94 flammability rating V2
Temperature range –40 °C to 100 °C
Printing black
Ordering data
Colour Availableinallcoloursoftheinternationalcolourcode;forMC
on request
● brown ● red ● orange
● yellow ● green ● blue
● violet ● grey white
Special printing Specify special printing and colours per diskette, Excel file or
using the M-Print® PRO software.
Minimum order quantity 1 pack
Notes on mounting Mount in strips when the marker pitch (width) corresponds to
the pitch of the terminals.
Forexample,DEK5mmpitchforterminalswith5mmpitch
suchastheWDU2.5.
Mount individual markers when the terminal pitch is larger than
the marker pitch (width).
Forexample,DEK6.5mountindividuallyonWDU6terminals.
G.43
Accessories
G
Terminal markers – Dekafix
Dekafix-theuniversalmarkerforSAKseries,
W-series,Z-series,P-seriesandI-seriesplus
WEICOSconnectorsandelectronicsdevices.
Clamping width: 3.5 mm Ordering data
DEK - blank Type Colour of material Length Qty. Order No.
DEK5/3,5MC white 5mm 500 1755270000
DEK - Custom printing Type Colour of material Length Qty. Order No.
DEK5/3,5MC white 5mm 100 1767730000
Clamping width: 5.0 mm
DEK - blank Type Colour of material Length Qty. Order No.
DEK5/5PlusMC white 5mm 1000 1854490000
DEK5/5PlusMCGE yellow 5mm 1000 1907520000
DEK5/5MC white 5mm 1000 1609801044
DEK5/5MCGE yellow 5mm 1000 1609801687
DEK5/5MCBL blue 5mm 1000 1609801693
DEK5/5MCGR grey 5mm 1000 1609801691
DEK5/5MCGN green 5mm 1000 1609801688
DEK5/5MCRT red 5mm 1000 1609801686
DEK5/30MC white 30mm 100 1951920000
DEK - Custom printing Type Colour of material Length Qty. Order No.
DEK5/5MC white 5mm 200 1609810000
DEK5/5PlusMC white 5mm 200 1854500000
DEK5/30MC white 30mm 20 1025680000
Clamping width: 6.0 mm
DEK - blank Type Colour of material Length Qty. Order No.
DEK5/6MC white 5mm 1000 1609820000
DEK5/6Plus MC white 5mm 100 1011320000
DEK - Custom printing Type Colour of material Length Qty. Order No.
DEK5/6MC white 5mm 200 1609830000
Clamping width: 6.5 mm
DEK - blank Type Colour of material Length Qty. Order No.
DEK5/6,5MC white 5mm 900 1609840000
DEK - Custom printing Type Colour of material Length Qty. Order No.
DEK5/6,5MC white 5mm 180 1609850000
Clamping width: 7.5 mm
DEK - blank Type Colour of material Length Qty. Order No.
DEK5/7,5MC white 5mm 320 1720620000
DEK - Custom printing Type Colour of material Length Qty. Order No.
DEK5/7,5MC white 5mm 320 1770490000
Clamping width: 8.0 mm
DEK - blank Type Colour of material Length Qty. Order No.
DEK5/8MC white 5mm 800 1856740000
DEK - Custom printing Type Colour of material Length Qty. Order No.
DEK5/8MC white 5mm 160 1856750000
G.44
Accessories
G
Terminal markers – Introduction – WS
WS markers are designed specifically for W series terminals.
Butthankstotheirsystemcompatibility,WSmarkerscan
alsobeusedwiththeIseries,ZseriesandPseries.The
generous size of these markers permit long characters strings
and multiple-line printing.
WS markers are ideal for labelling where long, individual
characterstringsarerequired.AndtheprovenMultiCard
format makes labelling possible with the SMark-Laser, PrintJet,
MCP Plus Plotter or MC-Mobilo as well.
• Mountinstripsorindividually
• MarkersintheprovenMultiCardformat
• ExcellentprintingqualitythankstotheWeidmüllerMultiCard
printers
WS
Halogen
Technical data
Material Polyamide66,halogen-free
UL 94 flammability rating V2
Temperature range –40 °C to 100 °C
Printing black
Ordering data
Colour Availableinallcoloursoftheinternationalcolourcode;forMC
on request
● brown ● red ● orange
● yellow ● green ● blue
● violet ● grey white
Special printing Specify special printing and colours per diskette, Excel file or
using the M-Print® PRO software.
Minimum order quantity 1 pack
Notes on mounting Mount in strips when the marker pitch (width) corresponds to
thepitchoftheterminals.Forexample,WS10/6=6mmpitch
forterminalswith6mmpitchsuchastheWDU4.
Mount individual markers when the terminal pitch is larger
thanthemarkerpitch(width).Forexample,WS12/6.5mount
individuallyonWDU6terminals.Weidmüllermarkerswith
5mmpitch(width)aresuitableforallwidthsofterminals.
G.45
Accessories
G
Terminal markers – Introduction – ZS
ZS
ZS markers – in the proven MultiCard format – were specially
developed for Z series terminals. They provide users with a
large labelling area. Their unique hinged form means that
cross-connectors, for example, are still readily accessible
without having to remove the marker. Markers can be clipped
on in strips to guarantee fast installation, but individual markers
are easily separated.
• Hingedlabellingarea
• Mountinstripsorindividually
• MarkersintheprovenMultiCardformat
• Flexible,fastprintingonsiteduringinstallation
Halogen
ZS
Technical data
Material Polyamide66,halogen-free
UL 94 flammability rating V2
Temperature range –40 °C to 100 °C
Printing black
Ordering data
Colour white
Notes on mounting heightxwidth(pitch),e.g.ZS10/5
10mmhigh,5mmwide=5mmpitch
Special printing Specify special printing and colours per diskette, Excel file or
using the M-Print® PRO software.
Suitable printing systems SMark-Laser, PrintJet, MCP Plus Plotter, MC-Mobilo
Minimum order quantity 1 pack
G.46
Accessories
G
Terminal markers – WS / ZS
WS markers are perfect for the connectors of the
W-series,I-series,P-seriesandZ-series.The
WS10/5and10/6Middle,arefittedwithacentre
footandcanbeusedfortheI-series.The
ZS markers are specially designed for the Z-series.
Clamping width: 3.5 mm Ordering data
WS - blank Type Colour of material Length Qty. Order No.
WS12/3,5MC white 12 mm 600 1778270000
WS - Custom printing Type Colour of material Length Qty. Order No.
WS12/3,5MC white 12 mm 120 1778280000
Clamping width: 5.0 mm
WS - blank Type Colour of material Length Qty. Order No.
WS8/5MC white 8 mm 720 1640740000
WS8/5MCGE yellow 8 mm 720 1773521687
WS8/5MCRT red 8 mm 720 1773521686
WS8/5MCBL blue 8 mm 720 1773521693
WS8/5MCOR orange 8 mm 720 1773521690
WS8/5PLUSMC white 8 mm 600 1951870000
WS10/5MC white 10 mm 720 1635000000
WS10/5MCMiddle white 10 mm 720 1792000000
WS10/5MCGE yellow 10 mm 720 1773531687
WS10/5MCRT red 10 mm 720 1773531686
WS10/5MCBL blue 10 mm 720 1773531693
WS12/5MC white 12 mm 720 1609860000
WS12/5MCGE yellow 12 mm 720 1773541687
WS12/5MCRT red 12 mm 720 1773541686
WS12/5MCBL blue 12 mm 720 1773541693
WS12/5MCOR orange 12 mm 720 1773541690
WS12/5MCPLUS white 12 mm 600 1927510000
WS14/5MC white 14 mm 480 1768090000
WS15/5MC white 15mm 480 1609880000
WS15/5MCGE yellow 15mm 480 1773571687
WS - Custom printing Type Colour of material Length Qty. Order No.
WS8/5MC white 8 mm 144 1640750000
WS10/5MC white 10 mm 144 1635010000
WS10/5MCMiddle white 10 mm 144 1792010000
WS12/5MC white 12 mm 144 1609870000
WS12/5MCPLUS white 12 mm 60 1927520000
WS15/5MC white 15mm 96 1609890000
Clamping width: 6.0 mm
WS - blank Type Colour of material Length Qty. Order No.
WS8/6PLUSMC white 8 mm 600 1951880000
WS10/6MC white 10 mm 600 1828450000
WS10/6MCMiddle white 10 mm 600 1818400000
WS10/6MCMiddleGN green 10 mm 600 1917420000
WS10/6MCMiddleGE yellow 10 mm 600 1917430000
WS10/6MCMiddleRT red 10 mm 600 1917440000
WS10/6MCMiddleOR orange 10 mm 600 1917410000
WS12/6MC white 12 mm 600 1609900000
WS12/6MCGE yellow 12 mm 600 1773551687
WS12/6MCRT red 12 mm 600 1773551686
WS12/6MCBL blue 12 mm 600 1773551693
WS12/6MCOR orange 12 mm 600 1773551690
WS12/6MCBR brown 12 mm 600 1773551692
WS12/6MCVI violet 12 mm 600 1773551689
WS12/6MCPLUS white 12 mm 600 1927530000
G.47
Accessories
G
Terminal markers – WS / ZS
WS markers are perfect for the connectors of the
W-series,I-series,P-seriesandZ-series.WS10/5
and10/6Middlearefittedwithacentrefootand
canbeusedfortheI-series.TheZSmarkersare
specially designed for the Z-series.
Ordering data
WS - Custom printing Type Colour of material Length Qty. Order No.
WS10/6MC white 10 mm 120 1828460000
WS10/6MCMiddle white 10 mm 120 1818410000
WS12/6MC white 12 mm 120 1609910000
WS12/6MCPLUS white 12 mm 120 1927540000
Clamping width: 6.5 mm
WS - blank Type Colour of material Length Qty. Order No.
WS12/6,5MC white 12 mm 540 1609920000
WS12/6,5MCGE yellow 12 mm 540 1773561687
WS12/6,5MCRT red 12 mm 540 1773561686
WS12/6,5MCBL blue 12 mm 540 1773561693
WS12/6,5MCGN green 12 mm 540 1773561688
WS - Custom printing Type Colour of material Length Qty. Order No.
WS12/6,5MC white 12 mm 108 1609930000
Clamping width: 8.0 mm
WS - blank Type Colour of material Length Qty. Order No.
WS10/8MC white 10 mm 420 1905950000
WS12/8MC white 12 mm 420 1906000000
WS - Custom printing Type Colour of material Length Qty. Order No.
WS10/8MC white 10 mm 84 1906030000
WS12/8MC white 12 mm 84 1906010000
Clamping width: 12.0 / 15.0 mm
WS - blank Type Colour of material Length Qty. Order No.
WS10/12MC white 10 mm 300 1905970000
WS10/15MC white 10 mm 240 1854090000
WS - Custom printing Type Colour of material Length Qty. Order No.
WS10/12MC white 10 mm 60 1906060000
WS10/15MC white 10 mm 48 1854100000
Clamping width: 5.0 mm
ZS - blank Type Colour of material Length Qty. Order No.
ZS10/5MC white 10 mm 480 1610000000
ZS15/5MC white 15mm 480 1646630000
ZS - Custom printing Type Colour of material Length Qty. Order No.
ZS10/5MC white 10 mm 96 1610010000
ZS15/5MC white 15mm 96 1646640000
Clamping width: 6.0 mm
ZS - blank Type Colour of material Length Qty. Order No.
ZS12/6MC white 12 mm 400 1610020000
ZS - Custom printing Type Colour of material Length Qty. Order No.
ZS12/6MC white 12 mm 80 1610030000
G.48
Accessories
G
Terminal markers – Tag carrier
ThistagholderisspeciallyconceivedfortheIDK1.5Ntwo-tierterminaloftheI-series.Theflexiblehinge
mechanismallowscross-connectionstobeconnectedordisconnectedatlittleeffort.Itcanbefittedwith
fourDEK5tagsortwoWS10/5Middleconnectormarkers.
Snap Mark Ordering data
Type Length Width Qty. Order No.
Technical specification SnapMarkI 23mm 5mm 50 1805880000
Material Polyamide66
UL 94 flammability rating V2
Min. temperature, continuous -40 °C
Max. temperature, continuous 100 °C
Colour of material white
Accessories
Type Length Width Qty. Order No.
WS10/5MCMiddle 10 mm 5mm 720 1792000000
DEK5/5MC 5mm 5mm 1000 1609801044
TheBZTmarkercarrierenablesclearlabellingoftheZDU2.5/4/6andZDUAterminalrange.TheBZTis
equippedwiththeWS10/5connectormarker.TheZAversionensuresmaximumstabilityduetoblock
construction of the marker carrier.
BZT1 / BZT2 Ordering data
Type Length Width Qty. Order No.
Technical specification BZT1 8 mm 5mm 100 1805490000
Material Polyamide BZT1ZA 8 mm 5mm 100 1805520000
UL 94 flammability rating V2 BZT2 12 mm 5mm 100 1805480000
Min. temperature, continuous -40 °C BZT2ZA 12 mm 5mm 100 1805530000
Max. temperature, continuous 100 °C
Colour of material beige
Accessories
Type Length Width Qty. Order No.
WS10/5MC 10 mm 5mm 720 1635000000
G.49
Accessories
G
Terminal markers – Tag carrier
TheSCHT5&SCHT5SgroupmarkercarrierisclippeddirectlytotheTS32DINrail(G-rail)orthe
TS35DINrail(top-hatrail).Itisthereforepossibletoprovideterminalstriplabellingirrespectiveofthe
terminal and the type of terminal.
SCHT 5 / SCHT 5 S Ordering data
Type Length Width Qty. Order No.
Technical specification SCHT5 44,5mm 19.5mm 20 0292460000
Material Polyamide66 SCHT5S 44,5mm 9.5mm 20 1631930000
UL 94 flammability rating V2
Min. temperature, continuous -40 °C
Max. temperature, continuous 100 °C
Colour beige
Accessories
Type Length Width No. per sheet Qty. Order No.
ESO5white 40 mm 16.5mm 60 10 1607710000
ESO5yellow 40 mm 16.5mm 60 10 1631350000
ESO5Pwhite 40 mm 16.5mm 60 10 1670370000
ESO5Pyellow 40 mm 16.5mm 60 10 1670380000
ESO5Swhite 40 mm 7mm 140 10 1631920000
STR5F.SCHT5 40 mm 16.5mm 20 0294000000
STR5S.F.SCHT5S 40 mm 7mm 20 1631940000
TheSCHT7isahingedgroupmarkercarrierforinlaytagswhichstillallowseasyaccesstotheclamping
screw.ToequipwithESO7,4tagsofDEK5/5or2tagsofWS10/5Middle.
SCHT 7 Ordering data
Type Length Width Qty. Order No.
Technical specification SCHT7 39.3mm 8 mm 20 0517960000
Material Polyamide66
UL 94 flammability rating V2
Min. temperature, continuous -40 °C
Max. temperature, continuous 100 °C
Colour white
Accessories
Type Length Width No. per sheet Qty. Order No.
DEK5/5MC 5mm 5mm 1000 1609801044
ESO7white 27mm 6.3mm 240 10 1607720000
ESO7yellow 27mm 6.3mm 240 10 1634780000
ESO7Pwhite 27mm 6.3mm 240 10 1670390000
ESO7Pyellow 27mm 6.3mm 240 10 1670400000
STR7SCHT7 27mm 6.3mm 20 0515300000
WS10/5MCMiddle 10 mm 5mm 720 1792000000
G.50
Accessories
G
Terminal markers – Tag carrier
SCHT9/4andSCHT14/6arehingedgroupmarkercarriersforsingledekafixandWStags,allowing
easy access to the clamping screws.
WGBgroupmarkercarrierforsingledekafixandWStags.TheWGBalsocoversthecross-connection
channels.
BlankWADcoversforlabellingwithSTIpen,oraspecialprintingfortheW-series.Cross-connection
channelsarecovered.AlsoavailablewithlightningflashwarningsymboltoDIN30600.
SCHT 9/4 / SCHT 14/6 Ordering data
Type Length Width Qty. Order No.
Technical specification SCHT14/6 44.3mm 6mm 20 1269060000
Material Polyamide66 SCHT9/4 32mm 4 mm 20 1278460000
UL 94 flammability rating V2
Min. temperature, continuous -40 °C
Max. temperature, continuous 100 °C
Colour beige
Accessories
Type Length Width Qty. Order No.
DEK5/5MC 5mm 5mm 1000 1609801044
WS12/5MC 12 mm 5mm 720 1609860000
WGB 5 / WGB 8 / WAD Ordering data
Type Length Width Colour Qty. Order No.
Technical specification WGB5 33.5mm 5mm beige 50 1050760000
Material Polyamide66 WGB8 33.5mm 7.7mm beige 50 1050960000
UL 94 flammability rating V2 WAD5 33.5mm 5mm white 50 1056060000
Min. temperature, continuous -40 °C WAD5lightningflash 33.5mm 5mm yellow 501053460000
Max. temperature, continuous 100 °C WAD8 33.5mm 8 mm white 50 1056160000
WAD8lightningflash 33.5mm 8 mm yellow 50 1053560000
WAD12 36.2mm 12 mm white 50 1056260000
WAD12lightningflash 36.2mm 12 mm yellow 50 1055960000
WAD27 64mm 27mm white 10 1062960000
WAD27lightningflash 64mm 27mm yellow 10 1062860000
WAD – Custom printing
Type Length Width Colour Qty. Order No.
WAD5 33.5mm 5mm white 100 1790060000
WAD8 33.5mm 8 mm white 50 1667700000
Accessories – WGB 5 / WGB 8
Type Length Width Qty. Order No.
DEK5/5MC 5mm 5mm 1000 1609801044
DEK5/30MC 5mm 30mm 100 1951920000
WS12/5MC 12 mm 5mm 720 1609860000
G.51
Accessories
G
Terminal markers – Tag carrier
TheZGB15/ZGB30isahingedmarkercarrier.Thetagholdercanbefittedwiththedekafix5,
WS12/5connectormarkersorwiththepush-intagESO15/ESO7.
TheEM8/30endbracketmarkerissuitableforlabellingtheWEW35/2andZEW35/2endbracketsas
wellasmarkercarrierforW-seriesterminals.TheEM8/30canbefittedwiththeESO7andESO7P
inlay tags. The pocket guarantees that the labelling is well protected against environmental influences.
ZGB 15 / ZGB 30 Ordering data
Type Length Width Qty. Order No.
Technical specification ZGB15 15mm 7mm 20 1636530000
Material Polyamide66 ZGB30 32mm 7mm 20 1611930000
UL 94 flammability rating V2
Min. temperature, continuous -40 °C
Max. temperature, continuous 100 °C
Colour white
Accessories
Type Length Width No. per sheet Qty. Order No.
DEK5/5MC 5mm 5mm 1000 1609801044
ESO7white 27mm 6.3mm 240 10 1607720000
ESO7yellow 27mm 6.3mm 240 10 1634780000
ESO7Pwhite 27mm 6.3mm 240 10 1670390000
ESO7Pyellow 27mm 6.3mm 240 10 1670400000
ESO15white 15mm 6mm 120 1 1636510000
STR7SCHT7 27mm 6.3mm 20 0515300000
STR15ZGB15 15mm 6.3mm 20 1636520000
WS12/5MC 12 mm 5mm 720 1609860000
EM 8/30 Ordering data
Type Length Width Qty. Order No.
Technical specification EM8/30 30mm 8 mm 50 1806120000
Material Polypropylene
UL 94 flammability rating HB
Min. temperature, continuous -40 °C
Max. temperature, continuous 80 °C
Colour transparent
Accessories
Type Length Width No. per sheet Qty. Order No.
ESO7white 27mm 6.3mm 240 10 1607720000
ESO7yellow 27mm 6.3mm 240 10 1634780000
ESO7Pwhite 27mm 6.3mm 240 10 1670390000
ESO7Pyellow 27mm 6.3mm 240 10 1670400000
G.52
Accessories
G
Overview Printing systems
The Weidmüller labelling systems are the quick and efficient
way of producing markers for connectors, wires, cables and
devices, plus labels for general use. The M-Print® PRO soft-
ware enables users to mark electrical equipment quickly and
simply.Forprofessionalandfastdesign,printingandordering
ofyourmarkingrequirements.Borders,barcodes,graphics
or photos can all be easily integrated. The multitude of data
conversion routines presents you with fast and flexible options
for data integration. The Weidmüller SMark-Laser, PrintJet
PRO, MCP Plus and MC-Mobilo printers plus those of the
ThermoMark series can be used for printing.
The unique printing speed of the SMark-Laser makes it a
real winner. The PrintJet PRO is the reference model in
industrial marking for high-resolution printing and maximum
wipe and scratch resistance. The MCP Plus plotter provides
you with good flexibility because with its positioning frame
it can handle more than 120 different types of marker in the
MultiCard format. The MC-Mobilo is the ideal printer for
labelling on site without a PC and a mains power supply,
directly during installation work. The printers of the
ThermoMarkseriesareidealforprintinglabelsand/orshrink-
able sleeves in excellent quality.
Printing systems and software
Printer
Type of marker SMark-Laser PrintJet PRO MCP Plus plotter MC-Mobilo ThermoMark
Connector markers
DEK ●●●●
WS ● ● ● ● 1
ZS ●●●●
MF ●●●●
Cable and wire markers
SF ● ● ● 2 ● 2
SFX ●●●●
SFC ●●●●
TM-I ●●●●
TwinMark ●
Device markers
DMC ●●●●
ESG ●●●●
SM ●●●●
ClipCard ●●●●
Labels
THMMT ●
THMWriteOn ●
1ExceptWS15/5
2SF4to6onlywithcorrespondingpositioningframe
G.53
Accessories
G
The SMark-Laser is a laser printer for printing
on markers in the MultiCard format. The fast pro-
duction of large numbers of individually printed
markers is the special feature of this printer. The
automatic feed function of the SMark-Laser
increases productivity even further and ensures
that your markers are available without delay.
• Fastprintingspeed,4MultiCardsperminute
• Markerscanbeusedimmediately
• Fastoperationirrespectiveofthefilesize
• Goodflexibilitythankstoproductionofmarkers
in MultiCard format to meet users’ requirements
• Reducesstocksbecauseonlyblankmarkers
are required
• Printingofgraphicsandlogosaswell
• Optionalautomaticfeedforlargequantities
• CanbeusedtogetherwiththeWeidmüller
M-Print® PRO software
SMark-Laser
Print options
Technical data
Type SMark-Laser
Application Prints all MultiCards
Technology Laser printer
Printing speed 4 MultiCards per minute
Print quality 600dpi
Printer drivers WIN9.x,NT,2000/XP
Software M-Print® PRO
System requirements Windows®2000/XP/Vista
Feed Manual or with optional loader
Interfaces Centronics
Power supply AC230V/50Hz/16A
Ambientconditions 20°C–35°C
Dimensions:(LxWxH) 1000x430x380mm
Scope of supply Laser printer, power cable, printer drivers, manual,
interface cable, M-Print® PRO software
Ordering data SMark-Laser
Type Order No.
SMark-Laser 1767090000
Rack 1782880000
Special toner cartridge 1770070000
Printing systems – Laser printer
G.54
Accessories
G
Printing systems – Inkjet printer
The PrintJet PRO inkjet printer prints markers for
electric connectivity. These markers can be used
for clear equipment identification on devices,
cables and connectors. The labelling makes
servicing, maintenance and troubleshooting much
easier. Water-based ink is used for the black or
spot colour printing. The print is crystal clear and
resistant to environmental influences.
The PrintJet PRO prints plastic markers in
MultiCardformat.Incombinationwiththeuser-
friendly M-Print® PRO software and the attached
loader, the printer becomes an essential part of
the production.The inkjet process being used, the
subsequent fusing, as well as the printer cartridge
and ink have all been specially adapted by
Weidmüller for industrial use. The printer has
excellent long-term use capabilities, thanks to its
integrated loader.
• Top-quality,resistantprinting
• Spotcolourprint
• Perfectforconstantuse
• Integratedloaderfor20MultiCards
• Idealforlargequantities
• Thedisplayshowsallrelevantinformation
• Flexibleconnectionoptions,fromLANportsto
USBports
PrintJet PRO
Technical data
PrintJet PRO
Type PrintJet PRO
Application Prints MultiCard markers
Technology Inkjetprocess
Print quality 600/1.200dpi
Printer drivers Windows®2000/XP/VISTA
Print software M-Print® PRO
System requirements Windows®2000/XP/VISTA
Feed Integratedloader
Fusing Thermal fusing
Interface USB,LAN
Power supply AC230VorAC115V
Location Office conditions
Ambienttemperature 20°to35°C
Dimensions(LxWxH) 1060x500x310mm
Weight 33kg
Cartridge system Inkcartridge,CMYK(480.000characters,Arialfontsize6)
Scope of supply PrintJet printer, power cable, printer drivers, manuals (CD),
USBcable,M-Print® PRO software
Ordering data PrintJet PRO
Type Order No.
PrintJetPRO115V 1024050000
PrintJetPRO230V 1001180001
Accessories
PJPROTNTKINKSETBK Inktankstarterset,black 1027090000
PJPROTNTKINKSETCOL Inktankstarterset,colour 1027110000
PJPROTNTKINKK ● InktankBlack 1027040000
PJPROTNTKINKC ●InktankCyan 1027050000
PJPROTNTKINKM ●InktankMagenta 1027060000
PJPROTNTKINKY ●InktankYellow 1027070000
PJPROTNTKFL Inktankfluid 1027080000
InktankPrintJetII 1858920000
CleanUnitPrintJetII 1858950000
InktankPrintJet 1797460000
Clean Unit PrintJet 4062150000
Note:Availablestartingthirdquarter,2008
G.55
Accessories
G
Printing systems – Plotter
The plotter MCP Plus complements the
WeimüllerMultiCardconcept.Itissuitablefor
smaller quantities of markers and when only part
of a MultiCard is to be printed on. The special
positioning frame for five MultiCards increases
productivity by 20 % over comparable systems.
WiththepositioningframeforSlimFixmarkers
sizes4to6,printingonmorethan120MultiCard
types for terminals, cables, wires and equipment
is possible. Labels are printed with the MCP-Label
positioning frame. Suitable for use with the
Weidmüller M-Print® PRO software.
• 2positioningframesformorethan120
MultiCard types
• MultiCardseasilyfittedintotheframe
• EasytousewithpartlyusedMultiCards
• Automaticpenactivationfunction
• Safestorageoftheplotterpens
MCP Plus
Ordering data MCP Plus
Type Order No.
MCP Plus plotter set 1925000000
Note:
Technical data
Type Plotter
Application printing of MultiCard markers and labels
Technology plotting technique
Print software M-Print® PRO
System requirements Windows®2000/XP/Vista
Interface Parallel Centronics
Power supply 230/115VAC
Feed manual
Location office conditions
Ambienttemperature 10°C-35°C
Dimensions(LxWxH) 660x440x125mm
Weight approx. 8 kg
Scope of supply MCPPluswithCentronicscable,USBcable,powerpack
(100-240VAC/50-60Hz),EuroandUSplugs,MultiCard
positioningframe,0.25mmplotterpen,M-Print® PRO
software and manual
G.56
Accessories
G
Printing systems – MCP Plus
TheSTI-SfelttippenissuitableforlabellingblankWeidmüllermarkingproducts.Itcanbeusedfor
handwrittenlabelsor,inconjunctionwiththeSTI-Sadapter,foraplotterprintout.Ablack,waterproofink
is used.
MCP positioning frames Ordering data
Type for Qty. Order No.
Technical specification MCPAP MultiCards 1 1924360000
MCPAPSF4-6 SlimFixsizes4to6 11924310000
MCPAPLabels Labels 1 1924370000
MCP plotter pens
Type for Qty. Order No.
Technical specification Plotter Pen 0.18 Reusable pen 1 1768570000
PlotterPen0.25 Reusable pen 1 1768540000
PlotterPen0.25P-Ink Disposable pen 8 ml 1 1920640000
PlotterPen0.35 Reusable pen 1 1768550000
PlotterPen0.35P-Ink Disposable pen 8 ml 1 1920650000
PlotterPen0.50 Reusable pen 1 1768560000
PlotterPen0.50P-Ink Disposable pen 8 ml 1 1005710000
PlotterPen0.70 Reusable pen 1 1011440000
PlotterPen0.70P-Ink Disposable pen 8 ml 1 1011450000
MCP ink
Type Contents Qty. Order No.
Technical specification P-Ink 22 ml 1 1924340000
Ink2000 25ml 11772120000
MCP miscellaneous
Type Contents Qty. Order No.
Technical specification MCP adhesive strips 1 1924320000
P cleaner 22 ml 1 1924330000
MCP cover 1 1924350000
Cleaner Clean 2000 25ml 11772130000
Cleaning beaker 1 1288300000
InlayforMCPPlus 11935130000
MCP software
Type Qty. Order No.
Technical specification M-PRINTPRO 11905490000
Accessories - STI pen Ordering data
Type Qty. Order No.
Technical specification AdapteraluminiumSTIpen 11762440000
STIpenSW 10 0508401694
G.57
Accessories
G
Printing systems – Plotter
The MC-Mobilo allows users to work directly at
place. There is no need for a PC and no need for
a power supply so electrical equipment can be
labelled anywhere, anytime. The rechargeable
batteryprovidespowerforupto3hours.The
universal inlay enables up to 120 different marker
types of the MultiCard range to be processed.
MC-Mobilo
Ordering data MC-Mobilo
MC-Mobilo Qty. Order No.
MC-Mobilo110/220V 11741260001
MC-Mobilo Accessories
Printkit(Ink2000,Clean2000,Plotter-Pen0,25) 11686920000
FrameinlaySF4-6 11802180000
Accessories Plotter IP220/MC-Mobilo
P-Ink 11924340000
Ink200025ml 11772120000
P cleaner 1 1924330000
CleanerClean200025ml 11772130000
Plotter pen 0.18 1 1768570000
Plotterpen0.25 11768540000
Plotterpen0.25P-Ink 11920640000
Plotterpen0.35 11768550000
Plotterpen0.35P-Ink 11920650000
Plotterpen0.50 11768560000
Plotterpen0.50P-Ink 1 1005710000
Plotterpen0.70 1 1011440000
Plotterpen0.70P-Ink 1 1011450000
Accessories – STI pen
AdapteraluminiumSTIpen 11762440000
STIpenSW 10 0508401694
Technical data
Type Plotter
Application Printing of MultiCard markers
Technology Plotting technique
Print software WM-Print
Interface RS232
Power supply AC230/AC115V
Feed manual
Location can be used anywhere
Ambienttemperature 15–30°C
Dimensions(LxWxH) 380x190x68mm
Weight 3kg
Scope of supply MC-Mobilo, universal power unit, including adapters (EURO,
UK,USA),datacassette,operatinginstructions,PowerPack,
PC connecting cable, WM-Print, universal MultiCard mounting
frame,0.25mmplotterpen,carrycase
G.58
Accessories
G
Printing systems – Software
Print and ordering software for markers and
labels
M-Print® PRO is a professional software for
printing and ordering Weidmüller markers and
labels under Windows®. This software helps you
to optimise your processes for marking electrical
equipment.Youcandesign,printandorderyour
marking materials effortlessly, professionally and
quickly: texts, frames, lines, graphics, barcodes,
serial numbers and photos.
M-Print® PRO Label Designer
Technical data
Here is an overview of the main functions
Integratedproductcatalogueforalllabelsandmarkers,includingimagesandlinkstotherelevantwebpagesandproductdatasheets
Markers and labels can be designed in as many levels as required
Customformattingofindividualtextcharacters(RTF)
Perform copy-and-paste functions with texts and their formats
SupportsUNICODEforforeign-languagetexts,suchasRussian,Chinese,Polish,etc.
Enter data on labels or worksheet
Permanent print preview: see how the printout will look during the design phase
Alphanumericcountsandsequences
Extensive range of image formats (*.bmp, *.wmf, *.png, *.ico, *.jpeg, *.tif, *.gif)
Imagelibraryincludingalltheimportantsymbolsusedinelectricalengineering
Assignproducttospecificprinter;forexample,ESG9/20toPrintJet,LaserMarktolaserprinter,etc.
Outputdevicessupported:PrintJetI+II,SMark-Laser,ThermoCard,THMaswellasstandardprinterswithWindowsdrivers,plotterMCPPlus
Optimum and rapid adjustment of the output devices
OnlineupdateserviceviatheInternet
InterfacetoRailDesigner®
Importassistanttocreateyourownimportfilterfornumerousfileformats(*.txt,*.asc,*.mak,*.wei,*.tmf,etc.)
ImportsdatafromCAEsystems
Operating systems supported
WINDOWS®2000/XP/Vista
System requirements
RAM >64MB
Processor >PentiumPIIIorcomparablemodel
Graphics >800x600pixelswith256colours
optimum:1024x768with16-bitHighColour
Harddrive >90MBfreestorage
Miscellaneous mouse, keyboard, CD-ROM drive (to install the software)
M-Print® PRO is available in two editions:
M-Print® PRO Standard Edition for professional printing results with all of Weidmüller’s marking materials
M-Print®PROAdvancedEditionforprofessionalprintingresultswithallofWeidmüller’smarking
materials plus labels to customer specification
Ordering data M-Print® PRO
Type Order No.
M-Print® PRO 1905490000
M-Print® PRO advanced 1905500000
G.59
Accessories
G
G.60
Accessories
G
Tools
Cutter
• Cuttingformationfordifferentcablesizes
increasesthequalityofthecutsforsmaller
cross-sections.
Cuttingtoolthatdoesnotdamagetheconductor;
forcuttingcopperandaluminiumcableswitha
diameterofupto8mm.
• Notsuitableforsteelwires,steel-armoured
cables,aluminiumalloysandhard-drawn
copperconductors!
Cuttingtoolthatdoesnotdamagetheconductor;
forcuttingcopperandaluminiumcableswitha
diameterofupto12mm.
• Notsuitableforsteelwires,steel-armoured
cables,aluminiumalloysandhard-drawn
copperconductors!
KT8
16/6
16/6
16/6
8
16/6
8
16
8
165/65/25
180
Toolclosed
Type Qty. Order No.
KT8 1 9002650000
Type Qty. Order No.
Technical data
Max. cutting performance copper cable
Solid(max.conductorcross-section) mm2/AWG
Stranded(max.conductorcross-section) mm2/AWG
Flexible(max.conductorcross-section) mm2/AWG
Flexible,Stranded(max.diameter) mm
Sectorline
Max. cutting performance aluminium cable
Stranded(max.conductorcross-section) mm2/AWG
Stranded(max.diameter) mm
Solid mm2
Data-/ telephone-/ control cable
O.D.max. mm
Tool data
Length/width/height mm
Weight g
Information
Ordering data
Version
Information
Accessories
Information
KT12
16/6
25/3
35/2
12
25/6
8
25
12
215/66/28
300
Toolclosed
Type Qty. Order No.
KT12 1 9002660000
Type Qty. Order No.
KT 8
Notching tool
KT 12
Notching tool
G.61
Accessories
G
Tools
Toolforpunchingoutthecross-connection
windowsoftheWeidmüllerW-Series,
Test-disconnectterminalWTR2.5,
FuseterminalWSI6.
Cutterfornon-pinchcuttingofWeidmüller
Z-seriescross-connections.
ToolfortrimmingpolesfromWQV2.5toWQV35
crossconnectionsusedinWeidmuellerW-Series
terminals.
Technical data
Length 167mm
Weight 227g
Ordering data
Type Qty. Order No.
WAW1 1 9004500000
WAW 1
Notching tool
WAW 2
Notching tool
KT ZQV
Cutter
Technical data
Length 205mm
Weight 338g
Ordering data
Type Qty. Order No.
WAW2 1 9004510000
Technical data
Length 215mm
Weight 300g
Ordering data
Type Qty. Order No.
KTZQV 1 9002170000
G.62
Accessories
G
Tools
Mountingrailcuttingandpunchingtoolfor:
• TS35/7.5mmtoEN50022(s=1.0mm)
• TS35/15mmtoEN50022(s=1.5mm)
• TS32mmtoEN50035(s=1.5mm)
• TS15/5.5mmtoEN50045(s=1.0mm)
• Coppergroundingrail10mmx3mm
Punching
Cross-andlengthwisepunches(elongatedhole
12x6.4mm)
(s=materialdensityofthemountingrail)
Technical data
Width 205mm
Length 270mm
Height 200mm
Weight 19000g
Ordering data
Type Qty. Order No.
TSLD 1 9918700000
TSLD
Terminal rail cutting and punching tool
G.63
Accessories
G
Tools
Cable cutter
• Easyhandling
• Minimalhandforcerequired
• Releaseoptionineverycuttingposition
KT 45 R
300/600
400/800
45
3x70SM
400/800
45
3x70SE
45
290/40/85
740
Toolclosed
Type Qty. Order No.
KT45R 1 9202040000
Thedimensionsofthecablecutterrefertothedeliverycondition,i.e.the
pointofthehingedbladeparalleltothexedblade.
Type Qty. Order No.
SparehingedbladeKT45R 19204270000
Technical data
Max. cutting capacity copper cable
Solid(max.conductorcross-section) mm2/kcmil
Stranded(max.conductorcross-section) mm2/kcmil
Flexible(max.conductorcross-section) mm2/kcmil
Flexible,Stranded(max.diameter) mm
Sectorconductor
Max. cutting capacity aluminium cable
Stranded(max.conductorcross-section) mm2/kcmil
Stranded(max.diameter) mm
Sectorconductor mm2
Data-/ telephone-/ control cable
O.D.max. mm
Tool data
Length/width/height mm
Weight g
Information
Ordering data
Version
Information
Accessories
Information
KT 45 R
G.64
Accessories
G
Tools
Sheathing stripper
• SheathingstripperforPVCcables
• SheathingstripperforPVC-insulatedround
cable
• Insulationcanbestrippedfromanypointalong
thecable
• Alsoverywellsuitedforstrippingcablesin
cableducts
• Hingedbladeforcircumferentialandlongi-
tudinalcuts
• Handletipswithintegratedcutterforopening
slitinsulation
AM 16
PVCroundcable
6…17.3
0.8-2.5
53
60
Type Qty. Order No.
AM16 1 9204190000
Type Qty. Order No.
Spareblade 19204260000
Technical data
Max. stripping performance
Cablemodel
Conductorcross-section mm2
Conductordiameter mm
Max.strippinglength mm
Adjustabledepthofcut mm
Cutting performance
Max.cuttingperformance mm2
Tool data
Length mm
Weight g
Information
Ordering data
Version
Information
Accessories
Information
AM 16
G.65
Accessories
G
Tools
Stripping and cutting tools
• ForexibleandmassiveconductorswithPVC-
insulation
• Strippinglengthadjustablewithshoulder
• automaticopeningoftheclampingjawsafter
stripping
• nosplicingofthesingleconductor
• adjustabletodifferentinsulationthicknesses
• cablewithdoubleinsulationintwoprocessing
stepswithoutspecialadjustment
• Blade-devicefreefromoatandself-adjustable
• longdurability
• optimisedergonomicallydesign
Strippingandcuttingtoolforexibleconductors
withPVC-insulation
of0.08...6mm2(~AWG28...10)
• Nodamagingoftheconductorduetospecial,
self-adjustablestrippingblades
• Processingofmulti-conductors,withthinat
ribboncablesevenmultipleconductorsinone
operation
Strippingandcuttingtoolforexibleandmassive
conductorswithPVC-insulation
of6...16mm2(~AWG10...6)
• Cuttingofexibleandmassiveconductorsup
to6mm2(AWG10)
• Nodamagingoftheconductorduetospecial
bladeforms
stripax®
exible&solidconductorswithPVCinsulation
0.08…6
20
6
190
155
Type Qty. Order No.
STRIPAX 1 9005000000
Type Qty. Order No.
Cleaningbrush 59005450000
Sparestrippingblades 1 9054030000
Technical data
Max. stripping performance
Cablemodel
Conductorcross-section mm2
Conductordiameter mm
Max.strippinglength mm
Adjustabledepthofcut mm
Cutting performance
Max.cuttingperformance mm2
Tool data
Length mm
Weight g
Information
Ordering data
Version
Information
Accessories
Information
stripax®stripax® 16
stripax® 16
exible&solidconductorswithPVCinsulation
6…16
20
6
190
155
Type Qty. Order No.
STRIPAX16 1 9005610000
Type Qty. Order No.
Cleaningbrush 59005450000
Sparestrippingblades 1 9054080000
G.66
Accessories
G
Tools
Crimping and cutting tool for wire end
ferrules
• Cutting
• Stripping
• Crimping
• Conductorentrysideways
• WireendferrulesacoordingtoDIN46228-4
• Ratchetforprecisecrimping
• Efficientoperation:
Changeoftoolsnotnecessary,therefore
significantsavingoftime
• automatictransportofwireendferrules
•
Onlywireendferrulesinstripsof50piecesmay
beusedwiththistool.Theuseofwireend
ferrulesonreelscanleadtodamage.
Technical data
Description of contact
Typeofcontact
Crimpingrange mm2
Crimpingrange1(withmultiplecrimpingpositions) mm2
Crimpingrange2(withmultiplecrimpingpositions) mm2
Crimpingrange3(withmultiplecrimpingpositions) mm2
Plugwidth mm
Tool data
Length mm
Weight g
Information
Ordering data
Version
Information
Accessories
Information
stripax® plus 2.5
Cutting, stripping and crimping tool for wire
end ferrules
Cutting,strippingandcrimpingtoolforlinkedwire
endferrulesonstripwith0.5...2.5mm2
(~AWG20...14)fromWeidmüller
• Easyhandlingofwireendferrules
• Automaticfeedingofwireendferrules
stripax® plus 2.5
Stripofwireendferrules
0.5...2.5
0.5...0.75
1...1.5
2.5
210
260
OnlyWeidmüllerwireendferrulesonstripsà50piecesmaybeused.
Theusageofwireendferrulessuppliedbythemetremaycausefailures.
Type Qty. Order No.
stripaxplus2,5 1 9020000000
Sparecutter(orderno.:9050340000)
G.67
Accessories
G
Tools
Crimping tools for wire end ferrules
• Ratchetforprecisecrimping
• Releasemechanismincaseofincorrect
operation
• Entryforwireendferruleontheside
Technical data
Description of contact
Typeofcontact
Crimpingrange mm2
Crimpingrange1(withmultiplecrimpingpositions) mm2
Crimpingrange2(withmultiplecrimpingpositions) mm2
Crimpingrange3(withmultiplecrimpingpositions) mm2
Crimpingrange4(withmultiplecrimpingpositions) mm2
Crimpingrange5(withmultiplecrimpingpositions) mm2
Tool data
Length mm
Weight g
Information
Ordering data
Version
Information
Accessories
Information
PZ 4
Crimping tool for wire end ferrules from
0.5...4 mm2
Crimpingtoolforwireendferrules(toDIN46228
part1and4)withandwithoutplasticcollarand
twinwireendferrulesof0.5...2.5mm2
• Onlyonecrimpingstationforthewholecross-
section
PZ 4
Wireendferruleswith/withoutplasticcollar
0.5...4
200
448
Type Qty. Order No.
PZ4 1 9012500000
PZ 6/5
Crimping tool for wire end ferrules from
0.25...6 mm2
Crimpingtoolforwireendferrules(toDIN46228
pt.1and4)withandwithoutplasticcollarof
0.25...6mm2(~AWG24...10)andtwinwireend
ferrulesof0.5...4.0mm2
• CrimpaccordingtoEuro-NormEN60947-1
• Fivecrimpingstationscorrespondingtothe
conductorcross-section
• ApprovalaccordingtoVG95211(military
designationVG95236T14B002)
PZ 6/5
Wireendferruleswith/withoutplasticcollar
0.25...6
0.25...0.5
0.75...1.5
2.5
4
6
200
423
Type Qty. Order No.
PZ6/5 1 9011460000
G.68
Accessories
G
Tools
Crimping tools for wire end ferrules
• Ratchetforprecisecrimping
• Releasemechanismincaseofincorrect
operation
Technical data
Description of contact
Typeofcontact
Crimpingrange mm2
Crimpingrange1(withmultiplecrimpingpositions) mm2
Crimpingrange2(withmultiplecrimpingpositions) mm2
Crimpingrange3(withmultiplecrimpingpositions) mm2
Plugwidth mm
Tool data
Length mm
Weight g
Information
Ordering data
Version
Information
Accessories
Information
PZ 3
Crimping tool for wire end ferrules from
0.5...6 mm2
Crimpingtoolforwireendferrulesof0.5...6mm2
withandwithoutplasticcollaraccordingto
DIN46228part1and4(~AWG20...10)and
twin-wireendferrulesof0.5...4mm2
• Onlyonedieforthewholecross-section
• Wireendferruleinsertionfromthefront
PZ 3
Wireendferruleswith/withoutplasticcollar
0.5...6
200
426
Type Qty. Order No.
PZ3 1 0567300000
PZ 6 roto
Crimping tool for wire end ferrules from
0.14...6 mm2
Crimpingtoolforwireendferrulesof0.14...6mm2
withandwithoutplasticcollartoDIN46228part1
and4(~AWG26...10)andtwin-wireendferrules
of0,5...4mm2
• Onlyonedieforthewholecross-section
• Pivoteddieforwireendferrule-insertion
• Wireendferruleinsertionfromthefrontorfrom
theside
PZ 6 roto
Wireendferruleswith/withoutplasticcollar
0.14...6
200
428
Type Qty. Order No.
PZ6roto 1 9014350000
G.69
Accessories
G
Tools
Crimping tools for wire end ferrules
• Ratchetforprecisecrimping
• Releasemechanismincaseofincorrect
operation
• Entryforwireendferruleontheside
Technical data
Description of contact
Typeofcontact
Crimpingrange mm2
Crimpingrange1(withmultiplecrimpingpositions) mm2
Crimpingrange2(withmultiplecrimpingpositions) mm2
Crimpingrange3(withmultiplecrimpingpositions) mm2
Plugwidth mm
Tool data
Length mm
Weight g
Information
Ordering data
Version
Information
Accessories
Information
PZ 16
Crimping tool for wire end ferrules from
6...16 mm2
Crimpingtoolforwireendferrules(toDIN46228
part1and4)withandwithoutplasticcollarfrom
6...16mm2(~AWG10...6)
• Threecrimpingstationscorrespondingtothe
conductorcross-sections
• CrimpaccordingtoEuro-NormEN60947-1
• ApprovalaccordingtoVG95211(military
designationVG95236T14B002)
PZ 16
Wireendferruleswith/withoutplasticcollar
6...16
6
10
16
200
418
Type Qty. Order No.
PZ16 1 9012600000
PZ ZH 16
Crimping tool for twin wire end ferrules,
6...16 mm2
Crimpingtoolfortwinwireendferrules(to
DIN46228pt.4)withplasticcollarfrom6...16mm2
(~AWG10...6)
• Threecrimpingstationscorrespondingtothe
conductorcross-sections
PZ ZH 16
Twinwireendferrules
6...16
6
10
16
260
700
Type Qty. Order No.
PZZH16 1 9013600000
G.70
Accessories
G
Tools
Crimping tools for wire end ferrules
• Ratchetforprecisecrimping
• Releasemechanismincaseofincorrect
operation
Technical data
Description of contact
Typeofcontact
Crimpingrange mm2
Crimpingrange1(withmultiplecrimpingpositions) mm2
Crimpingrange2(withmultiplecrimpingpositions) mm2
Crimpingrange3(withmultiplecrimpingpositions) mm2
Plugwidth mm
Tool data
Length mm
Weight g
Information
Ordering data
Version
Information
Accessories
Information
PZ 50
Crimping tool for wire end ferrules with 25, 35
and 50 mm2
Crimpingtoolforwireendferrulesof25,35and
50mm2withandwithoutplasticcollarto
DIN46228part1and4(~AWG3...1)
• Threecrimpingstationscorrespondingtothe
conductorcross-sections
• CrimpaccordingtoEuro-NormEN60947-1
• ApprovalaccordingtoVG95211(military
designationVG95236T14B002)
PZ 50
Wireendferruleswith/withoutplasticcollar
25...50
25
35
50
260
700
Type Qty. Order No.
PZ50 1 9006450000
G.71
Accessories
G
Tools
Rechargeable torque screwdriver
Technical data
Screwdriver
Motor
Idlingspeed
Max.torque
Chuck
Length
Weight
Battery
Type
Weight
Charger
Input
Output
Chargingtime
Weight
Ordering data
Accessories
DMS 3
DMS 3 rechargeable torque screwdriver
• One-handoperationunderallworking
conditions
•Switchableforwardandreverse
•Twospeeds:200and400rpm
•Precisetorquesettingsfrom
approx.0.2...3Nmin6steps
•Consistentperformanceduringbattery
discharge
•Gripswingseasilyfromrodtopistolform
•Takes1/4"bitsheldball-bearingclamping
mechanism(formE6.3)
•Safetylockpreventsinadvertentoperation
•Easychangeoverfrombatterydrivetomanual
operationupto15Nm
2.4VDC
200/400min-1
3.0Nm
1/4"E6.3DIN3126
239mm
400g
2Ni-Cdbatterieseach1.2V
122g
230VAC,50Hz,50mA
2.9VAC,1.4A,4.1VA
1hour
700g
Type Qty. Order No.
DMS3 1 9007440000
Screwdriverincl.battery
Type Qty. Order No.
Sparebattery 1 9007450000
Charger 1 9007460000
DMS 3 Set
Type Qty. Order No.
DMS3set1(screwdriverincl.battery,
1 9007470000
charger,bits,plasticcarryingcase)*
DMS3set2(asset1 1 9007480000
with1additionalbattery)
*)refertofigure
G.72
Accessories
G
Tools
Electric torque screwdriver
Technical data
Ratedvoltage
Frequency
Ratedpower
Currentconsumption
rpmofspindle insearchgear
inworkingmode
Torques
Level1(M2.5)
Level2(M3)
Level3(M3.5)
Level4(M4)
Weightincl.supplycable
Weight
NoiseleveltoDIN45634
ProtectionclassIItoDIN57740
DIN/VDE0740T.1andT.2
EMCtoECdirective89/336/EWG
CEmark
Ordering data
Standard equipment
Accessories
BalancerforhanginguptheDMS2
DMS 2 Set
• Torqueadjustableinfourstepsfor
standardscrewsM2.5toM4
•Selectableelectricpowercut-offupon
reachingapreselectedtorque
•Highrepetitionaccuracy
•Start-upinlowgearandswitchoverto
operatingrpmiscontrolledviathepressure
onthescrewhead
•Switchableforwardandreverse
•Fatigue-freeworkingduetoergonomicdesign
andlowweight
•Idealdesignforone-handoperationunderall
workingconditionsandatdifferentworking
locations
•Lownoise
•Lowenergyconsumption
230V
60Hz
45W
0.2A
350min-1
700min-1
0.5±0.1Nm
0.7±0.15Nm
1.2±0.2Nm
1.7±0.25Nm
0.990kg
0.820kg
58db(A)
Type Qty. Order No.
DMS2with1/4"drive 1 0664600000
FormE6.3DIN3126withhang-upclipand4bitsforslottedscrews(Length:50mm)
Bladedimensions0.5x3/0.6x3.5/0.8x4/1.0x5.5
Type Qty. Order No.
BAL2(balancerforhanginguptheDMS2) 1 0181800000
G.73
Accessories
G
Tools
Combined cutting and
screw driving tool
thatdoesnotdamagetheedge;forcuttingof
coppercableswithadiameterofupto1.5mm2
solidand2.5mm2flexible.
Technical data
Maximum cutting capacity
Copper cable:
Solidcable(conductorcross-section) mm2
Flexiblecable(conductorcross-section) mm2
Tool data
Lengthxwidthxheight mm
Weight g
Ordering data
swifty®
swifty®
• Cablecuttingtooltomountonnon-insulated
screwdriverswithabladediameterof3.5mm
•Minimummanualforcerequired
•Automaticopeningofthecutter
•Ergonomicallydesignedgrip
swifty®set
• Efficientoperation:
•Onlyonetoolforcable-processing
inIDC-technology
•Suitableforscrewandtensionclamps
•Readilyavailablepocketsize
•Forright-handedandleft-handeduse
•One-handoperation
swifty®set
1.5
2.5
35/18/40
20
Type Qty. Order No.
swifty®(withoutscrewdriver) 1 9006020000
Type Qty. Order No.
swifty®set(withscrewdriver)
1 9006060000
Screwdriver 1 9008330000
(SD0.63.5x100)
G.74
Accessories
G
VDE insulated screwdriver
VDE insulated screwdriver sets, for working on live parts up to 1000 V
AC and 1500 V DC, DIN EN 60900, IEC 900. safety tested GS, every one
tested. Blade made from fully hardend, high-alloy chromium-vanadium-
molybdenum steel, gunmetal finish.
Type Size / SW A B C Order No.
SDI S
VDE insulated slot-head screwdriver, SDI DIN 7437, ISO 2380/2,
output to DIN 5264, ISO 2380/1, SoftFinish grip
SDI 0.4 x 2.5 x 75 0.4 2.5 80 9008370000
SDI 0.5 x 3.0 x 100 0.5 3.0 100 9008380000
SDI 0.6 x 3.5 x 100 0.6 3.5 100 9008390000
0.8 x 4.0 x 100 0.8 4.0 100 9008400000
SDI 1.0 x 4.5 x 125 1.0 4.5 125 9008910000
SDI 1.0 x 5.5 x 125 1.0 5.5 125 9008410000
SDI 1.2 x 6.5 x 150 1.2 6.5 125 9025870000
SDI 1.6 x 8.0 x 175 1.6 8.0 175 9008430000
SDI 0.4 x 2.0 x 60 0.4 2.0 60 9205690000
SDI 1.0 x 4.5 x 175 1.0 4.5 175 9205700000
SDI 1.0 x 5.5 x 175 1.0 5.5 175 9205710000
SDIK PH
VDE insulated crosshead screwdriver, for Phillips screws, SDIK PH
DIN 7438, ISO 8764/2-PH, output to ISO 8764-PH, SoftFinish grip
SDIK PH0 0 60 9008560000
SDIK PH1 1 80 9008570000
SDIK PH2 2 100 9008580000
SDIK PH3 3 150 9008590000
SDIK PZ
VDE insulated crosshead screwdriver type Pozidriv SDIK PZ
DIN 7438, ISO 8764/2-PZ, output to ISO 8764-PZ, SoftFinish grip
SDIK PZ1 1 80 9008900000
SDIK PZ2 2 100 9008890000
SDIT
VDE insulated Torx®-screwdriver, SDIT SoftFinish grip SDI T8 8 60 9201940000
SDI T10 10 80 9009640000
SDI T15 15 80 9009650000
SDI T20 20 80 9009660000
SDI T25 25 80 9009670000
SDI T30 30 100 9009680000
SDI T35 40 150 9009690000
SKI
VDE insulated hexagon socket wrench, SKI SoftFinish grip SKI 5.0 x 125 5 125 9009000000
SKI 5.5 x 125 5.5 125 9008990000
SKI 6.0 x 125 6 125 9008980000
SKI 7.0 x 125 7 125 9008970000
SKI 8.0 x 125 8 125 9008960000
SKI 9.0 x 125 9 125 9008950000
SKI 10.0 x 125 10 125 9008940000
SKI 11.0 x 125 11 125 9008930000
SKI 13.0 x 125 13 125 9008920000
Information
Tools
G.75
Accessories
G
Uninsulated screwdriver
Weidmüller SoftFinish screwdriver for general uses, blade made from
fully hardened, high-alloy chromium-vanadium-molybdenum steel, matt
chrome finish.
Type Size / SW A B C Order No.
SDI S
Slotted screwdriver with round blade SD DIN 5265, ISO 2380/2, output
to DIN 5264, ISO 2380/1, ChromTop tip, SoftFinish grip
SD 0.4 x 2.0 x 60 0.4 2.0 60 9037160000
SD 0.4 x 2.5 x 75 0.4 2.5 75 9009030000
SD 0.5 x 3.0 x 80 0.5 3.0 80 9008320000
SD 0.6 x 3.5 x 100 0.6 3.5 100 9008330000
SD 0.6 x 3.5 x 200 0.6 3.5 200 9010110000
SD 0.8 x 4.0 x 100 0.8 4.0 100 9008340000
SD 1.2 x 6.5 x 150 1.2 6.5 150 9009010000
SD 0.8 x 4.5 x 125 0.8 4.5 125 9009020000
SD 1.0 x 5.5 x 150 1.0 5.5 150 9008350000
SDK PH
Crosshead screwdriver, Phillips, SDK PH DIN 5262, ISO 8764/2-PH,
ouput to ISO 8764-PH, ChromTop tip, SoftFinish grip
SDK PH0 0 60 9008470000
SDK PH1 1 80 9008480000
SDK PH2 2 100 9008490000
SDK PH3 3 150 9008500000
SDK PZ
Crosshead screwdriver, Pozidriv, SDK PZ DIN 5262, ISO 8764/2-PZ,
ouput to ISO 8764/1-PZ, ChromTop tip, SoftFinish grip
SDK PZ0 0 60 9008520000
SDK PZ1 1 80 9008530000
SDK PZ2 2 100 9008540000
SDK PZ3 3 150 9008550000
SD TH
Torx® TH screwdriver with hole in tip of blade (tamper-tesistant), SD
TH for screwing Torx® and Torx®-TH security screws (pin in centre of
Torx recess), ChromTop tip, SoftFinish grip
SD TH8 8 60 9009190000
SD TH10 10 80 9009180000
SD TH15 15 80 9009170000
SD TH20 20 100 9009160000
SD TH25 25 100 9009150000
SD TH30 30 115 9009140000
SK
Hexagon socket wrench SK DIN 3125, ouput to DIN 3125, SoftFinish
grip
SK 5.5 x 125 5.5 125 9009120000
SK 6.0 x 125 6 125 9009110000
SK 7.0 x 125 7 125 9009100000
SK 8.0 x 125 8 125 9009090000
SK 9.0 x 125 9 125 9009080000
SK 10.0 x 125 10 125 9009070000
SK 11.0 x 125 11 125 9009060000
SK 12.0 x 125 12 125 9009050000
SK 13.0 x 125 13 125 9009040000
Information
Tools
.
G.76
Accessories
G
Tools
Wrench set Weidmüller
Allen key made from fully hardened, high-alloy chromium-vanadium-
steel, to DIN ISO 2936 L (DIN 911), surface high-quality refined.
Type Size / SW A B C Order No.
SK WSD S
9-piece offset screwdriver set in Prostar holder, with MagicRing: holds
standard screws (size 3 and larger) in any position thanks to spring steel ring,
with ball point: for working at angles up to 25°.
1.5
2
2.5
3
4
5
6
8
10
SK WSD-S 1.5-10.0 9008850000
SK S
7-piece Allen key set 2
2.5
3
4
5
8
6
SKS 2.0-8.0 9008860000
SK S
7-piece Allen key set with MagicRing and ball point: holds standard
screws (size 3 and larger) in any position thanks to spring steel ring, with ball
point: for working at angles up to 25°.
2
2.5
3
4
5
6
8
SKS 2.0-8.0 MR 9008870000
TH S
8-piece Torx®-TH screwdriver set
with hole in the blade point (tamper-proof), for screwing Torx® and Torx®-TH
tamper-proof screws (centre pin in profile)
9
10
15
20
25
27
30
40
TH-S 9-40 9008880000
Information
G.77
Accessories
G
Tools
DMS manual / DMSI manual
Torque screwdrivers with insulation up to 1000 V (VDE)
• DMSImanual
The “DMSI manual” with integral window torque scale combined
with a Weidmüller 1000 V insulated (VDE) interchangeable blade
ensures controlled tightening of screws plus reliability in electri-
cal applications.
Every 1000 V insulated handle (VDE) and blade (VDE) is tested
and provides the necessary safety up to 1000 V AC/1500 V DC.
Torque screwdrivers
• DMSmanual
This is a versatile tool suitable for a variety of jobs, with integral
scale for easy reading of the torque value plus a Weidmüller
interchangeable blade.
Each model is available with two torque ranges:
• 0.5to1.7Nm
• 2.0to8.0Nm
• settingtoolincluded
Advantages:
• Compactandespeciallylightweightdesign
• Torquesetwithspecialtool(included)toensuretherightset-
ting
• Ergonomichandlesizetomatchthetorquerange
• EverytoolcheckedandgivenanIDNo.,100%qualitycontrol
with verification and product reference
• Audible,unmistakableclickuponreachingthetorque,no
unnecessary effort
• Interchangeableblademadefromhigh-qualitywear-resistant
tool steel
• Alltoolscomplywiththeaccuracystipulationsof:
ENISO6798,BSEN26789,ASMEB107.14M
• Operatingaccuracy:±6%ofsetscalevalue
Setting tool
Scale
G.78
Accessories
G
Tools
Uninsulated torque screwdriver
Type Size / SW A B C Order No.
DMS manual
Torque-screwdriver
EN ISO 6798, BS EN 26789, ASME B107.14M
DMSMANUELL0.5-1.7 0.5 - 1.7Nm 9918370000
DMSMANUELL2.0-8.0 2.0 - 8.0Nm 9918380000
WK K S
Interchangeable blades for torque-screwdriver
output according to DIN 5264, ISO 2380/1
WK S 0.4 x 2.5 max. 0.6Nm 0.4 2.5 175 9918520000
WK S 0.5 x 3.0 max. 0.6Nm 0.5 3.0 175 9918530000
WK S 0.6 x 3.5 max. 1.1Nm 0.6 3.5 175 9918540000
WK S 0.8 x 4.0 max. 2.5Nm 0.8 4.0 175 9918550000
WK S 1.0 x 5.5 max. 3.8Nm 1.0 5.5 175 9918560000
WK K PZ
Interchangeable blades for torque-screwdriver
output according to DIN 5260-PZ, ISO 8764/1-PZ
WK K PZ0 max. 0.9Nm 175 9918600000
WK K PZ1 max. 3.8Nm 175 9918610000
WK K PZ2 max. 5.5Nm 175 9918620000
WK K PH
Interchangeable blades for torque-screwdriver
output according to DIN 5260-PH, ISO 8764/1-PH
WK K PH0 max. 0.9Nm 175 9918570000
WK K PH1 max. 3.8Nm 175 9918580000
WK K PH2 max. 5.5Nm 175 9918590000
Information
G.79
Accessories
G
Tools
VDE insulated torque screwdriver
VDE insulated torque screwdriver Weidmüller SoftFinish electric for
work on live parts up to 1000 Vac and 1500 Vdc, DIN EN 60900,
IEC 900. GS symbol, every one tested.
Type Size / SW A B C Order No.
DMSI manual
VDE insulated torque-screwdriver
EN ISO 6798, BS EN 26789, ASME B107.14M
DMSIMANUELL0.5-1.7 0.5 - 1.7Nm 9918390000
DMSIMANUELL2.0-8.0 2.0 - 8.0Nm 9918400000
WK SI
VDE insulated interchangeable blades for VDE insulated torque-
screwdriver
output according to DIN 5264, ISO 2380/1
WK SI 0.4 x 2.5 max. 0.6Nm 0.4 2.5 175 9918410000
WK SI 0.5 x 3.0 max. 0.6Nm 0.5 3.0 175 9918420000
WK SI 0.6 x 3.5 max. 1.1Nm 0.6 3.5 175 9918430000
WK SI 0.8 x 4.0 max. 2.5Nm 0.8 4.0 175 9918440000
WK SI 1.0 x 5.5 max. 3.8Nm 1.0 5.5 175 9918450000
WK IK PH
VDE insulated interchangeable blades for VDE insulated torque-
screwdriver
output according to DIN 5260-PH, ISO 8764/1-PH
WK IK PH0 max. 0.9Nm 175 9918460000
WK IK PH1 max. 3.8Nm 175 9918470000
WK IK PH2 max. 5.5Nm 175 9918480000
WK IK PZ
VDE insulated interchangeable blades for VDE insulated torque-
screwdriver
output according to DIN 5260-PZ, ISO 8764/1-PZ
WK IK PZ0 max. 0.9Nm 175 9918490000
WK IK PZ1 max. 3.8Nm 175 9918500000
WK IK PZ2 max. 5.5Nm 175 9918510000
Information
G.80
Accessories
G
Tools
Technical data
Ordering data
Type Qty. Order No.
IS 4 1 0485100000
IS 6 1 0407900000
IS 8 1 0235000000
Technical data
Ordering data
Type Qty. Order No.
IS 2 KG 1 1806630000
IS 3 KG 1 1806650000
IS 4 KG 1 1806660000
Technical data
Ordering data
Type Blade Order No.
BITE6.3Z 0.8 x 4.0 x 39 9025590000
BITE6.3Z 0.6 x 3.5 x 39 9025570000
SDIZ 0.8 x 4.0 9008460000
SDIZ 0.3 x 3.5 9008450000
IS 2 KG; IS 3 KG; IS 4 KG
Hexagon screwdriver
IS 4, IS 6, IS 8
Allen key
BIT E6.3Z, SDIZ
for fixing sockets
Hexagon screwdriver with cross-grip made from
high-quality plastics
• Surfacenickel-plated
• Madefromhardenedchromium-vanadiumsteel
• AccordingtoDIN6911
• DesignedforscrewstoDIN6912
Bitsandscrewdriverswithshoulderedbladesfor
fixing sockets to the Weidmüller range of modular
terminals.
• Nodamagetowallsaroundcontacts
• Madefromhardenedchrome-vanadiumsteel
• SuitableforallWeidmüllersockets
• BitholdersavailableforE6.3
• DIN3126forbitsandDINEN60900,IEC900
for screwdrivers
Allen key, with spigot
• Surfacenickel-plated
• Madefromhardenedchromium-vanadiumsteel
• AccordingtoDIN6911
• DesignedforscrewstoDIN6912
G.81
Accessories
G
Tools
Crimping tools for ferrules
PZ 1.5 stripax® PZ 3 PZ 4 PZ 6 PZ 6 HEX PZ 6/5 PZ 16 PZ 50
plus 2.5 roto
Order No.
9005990000 9020000000 0567300000 9012500000 9014350000 9013650000 9011460000 9012600000 9006450000
Ferrule mm2
H 0.25 l l l l
H 0.34 l l l l
H 0.5 ll1lllll
H 0.75 ll1lllll
H 1.0 ll1lllll
H 1.5 ll1lllll
H 2.5 l1lllll
H 4.0 lllll
H 6.0 l l l l l
H 10.0 l
H 16.0 l
H 25.0 l
H 35.0 l
H 50.0 l
l1 = ferrules in strip form only
Tools
Tools for insulated cable lugs
Tool Type of contact
Order No. 0.5 - 1.5 1.5 - 2.5 4.0 - 6.0
CTI 6 9006120000 l l l
CTI 6 S 9006210000 l l l
HTI 15 9014400000 l l
Station red blue yellow
Twin wire end ferrules are to be crimped according to the following table:
Tool Ferrules
Order No. H 0.5 H 0.75 H 1.0 H 1.5 H 2.5 H 4.0 H 6.0 H 10.0 H 16.0
PZ 1.5 9005990000 l l
PZ 3 0567300000 lllll
PZ 4 9012500000 lllll
PZ 6 roto 9014350000 llllll
PZ 6/5 9011460000 lllll
Station 1.5 mm21.5 mm22.5 mm22.5 mm24 mm26 mm2
PZ ZH 16 9013600000 l l l
G.82
Accessories
G
Wire end ferrules with plastic collar
Weidmüller colour code Ordering data
packed loose Type ø mm2AWG L1 L2 D1 D2 S1 S2
Stripping length
Colour Qty. Order No.
H0.25/10 0.25 24 10.0 6.0 0.8 1.8 0.15 0.25 8.0 l light blue 500 9025740000
H0.25/12 0.25 24 12.0 8.0 0.8 1.8 0.15 0.25 10.0 l light blue 500 9025760000
H0.34/10 0.34 22 10.0 6.0 0.8 2.0 0.15 0.25 8.0 l turquoise 500 9025750000
H0.34/12 0.34 22 12.0 8.0 0.8 2.0 0.15 0.25 10.0 l turquoise 500 9025770000
H0.5/12 0.50 20 12.0 6.0 1.0 2.6 0.15 0.25 8.0 l orange 500 0409500000
H0.5/14 0.50 20 14.0 8.0 1.0 2.6 0.15 0.25 10.0 l orange 500 0690700000
H0.5/16 0.50 20 16.0 10.0 1.0 2.6 0.15 0.25 12.0 l orange 500 9025870000
H0.75/12 0.75 18 12.0 6.0 1.2 2.8 0.15 0.25 8.0 m white 500 0409600000
H0.75/14 0.75 18 14.0 8.0 1.2 2.8 0.15 0.25 10.0 m white 500 0462900000
H0.75/16 0.75 18 16.0 10.0 1.2 2.8 0.15 0.25 12.0 m white 500 9025860000
H0.75/18 0.75 18 18.0 12.0 1.2 2.8 0.15 0.25 14.0 m white 500 9025910000
H1.0/12 1.00 17 12.0 6.0 1.4 3.0 0.15 0.25 8.0 l yellow 500 0409700000
H1.0/14 1.00 17 14.0 8.0 1.4 3.0 0.15 0.25 10.0 l yellow 500 0463000000
H1.0/16 1.00 17 16.0 10.0 1.4 3.0 0.15 0.25 12.0 l yellow 500 9025950000
H1.0/18 1.00 17 18.0 12.0 1.4 3.0 0.15 0.25 15.0 l yellow 500 9025930000
H1.5/14 1.50 16 14.0 8.0 1.7 3.5 0.15 0.25 10.0 l red 500 0463100000
H1.5/16 1.50 16 16.0 10.0 1.7 3.5 0.15 0.25 12.0 l red 500 0635100000
H1.5/24 1.50 16 24.0 18.0 1.7 3.5 0.15 0.25 20.0 l red 500 0565600000
H2.5/14D 2.50 14 14.0 8.0 2.2 4.2 0.15 0.25 10.0 l blue 500 9019160000
H2.5/18D 2.50 14 18.0 12.0 2.2 4.2 0.15 0.25 14.0 l blue 500 9019170000
H2.5/24D 2.50 14 24.0 18.0 2.2 4.2 0.15 0.25 20.0 l blue 500 9019180000
H4.0/17D 4.00 12 17.0 10.0 2.8 4.8 0.2 0.3 12.0 l grey 500 9019190000
H4.0/20D 4.00 12 20.0 12.0 2.8 4.8 0.2 0.3 14.0 l grey 500 9019200000
H4.0/26D 4.00 12 26.0 18.0 2.8 4.8 0.2 0.3 20.0 l grey 100 9019210000
H6.0/20 6.00 10 20.0 12.0 3.5 6.3 0.2 0.3 14.0 l black 100 0533500000
H6.0/26 6.00 10 26.0 18.0 3.5 6.3 0.2 0.3 20.0 l black 100 0565700000
H10.0/22 10.00 7 22.0 12.0 4.5 7.6 0.2 0.4 15.0 l ivory 100 0534200000
H10.0/28 10.00 7 28.0 18.0 4.5 7.6 0.2 0.4 21.0 l ivory 100 0565800000
H16.0/24 16.00 6 24.0 12.0 5.8 8.8 0.2 0.4 15.0 l green 100 0565900000
H16.0/28 16.00 6 28.0 18.0 5.8 8.8 0.2 0.4 21.0 l green 100 0566000000
H25.0/30 25.00 3 30.0 16.0 7.3 11.2 0.2 0.4 18.0 l brown 50 0317000000
H25.0/36 25.00 3 36.0 22.0 7.3 11.2 0.2 0.4 24.0 l brown 50 0317100000
H35.0/30 35.00 2 30.0 16.0 8.3 12.7 0.2 0.4 19.0 l beige 50 0317200000
H35.0/39 35.00 2 39.0 25.0 8.3 12.7 0.2 0.4 28.0 l beige 50 0317300000
H50.0/36 50.00 1 36.0 20.0 10.3 15.0 0.3 0.5 26.0 l olive green 50 0444200000
H70.0/40 70.00 2/0 37.0 20.0 12.7 16.0 0.35 0.6 26.0 l yellow 25 9028200000
H95.0/44 95.00 3/0 44.0 25.0 14.7 18.0 0.35 0.6 31.0 l red 25 9028210000
H120.0/50 120.00 4/0 50.0 30.0 16.5 21.0 0.5 0.7 36.0 l blue 25 9028220000
H150.0/54 150.00 300 MCM 54.0 32.0 18.5 23.5 0.5 0.75 38.0 l yellow 25 9028230000
Weidmüller colour code Ordering data
Iin multipack bag Type ø mm2AWG L1 L2 D1 D2 S1 S2
Stripping length
Colour Qty. Order No.
H0.14/10 0.14 26 10.0 6.0 0.6 1.5 0.15 0.25 8.0 l grey 500 9005180000
H0.14/12 0.14 26 12.0 8.0 0.6 1.5 0.15 0.25 10.0 l grey 500 9028240000
H0.25/10 0.25 24 10.0 6.0 0.8 1.8 0.15 0.25 8.0 l light blue 500 9026050000
H0.25/12 0.25 24 12.0 8.0 0.8 1.8 0.15 0.25 10.0 l light blue 500 9025780000
H0.34/10 0.34 22 10.0 6.0 0.8 2.0 0.15 0.25 8.0 l turquoise 500 9026030000
H0.34/12 0.34 22 12.0 8.0 0.8 2.0 0.15 0.25 10.0 l turquoise 500 9025790000
H0.5/10 0.50 20 10.0 6.0 1.0 2.6 0.15 0.25 8.0 l orange 500 9028260000
H0.5/14 0.50 20 14.0 8.0 1.0 2.6 0.15 0.25 10.0 l orange 500 9026060000
H0.5/16 0.50 20 16.0 10.0 1.0 2.6 0.15 0.25 12.0 l orange 500 9028270000
H0.75/12 0.75 18 12.0 6.0 1.2 2.8 0.15 0.25 8.0 m white 500 9028280000
H0.75/14 0.75 18 14.0 8.0 1.2 2.8 0.15 0.25 10.0 m white 500 9026070000
H0.75/16 0.75 18 16.0 10.0 1.2 2.8 0.15 0.25 12.0 m white 500 9028290000
H0.75/18 0.75 18 18.0 12.0 1.2 2.8 0.15 0.25 14.0 m white 500 9028300000
H1.0/12 1.00 17 12.0 6.0 1.4 3.0 0.15 0.25 8.0 l yellow 500 9028310000
H1.0/14 1.00 17 14.0 8.0 1.4 3.0 0.15 0.25 10.0 l yellow 500 9026080000
H1.0/16 1.00 17 16.0 10.0 1.4 3.0 0.15 0.25 12.0 l yellow 500 9028320000
H1.0/18 1.00 17 18.0 12.0 1.4 3.0 0.15 0.25 15.0 l yellow 500 9028340000
H1.5/14 1.50 16 14.0 8.0 1.7 3.5 0.15 0.25 10.0 l red 500 9026090000
H1.5/16 1.50 16 16.0 10.0 1.7 3.5 0.15 0.25 12.0 l red 500 9028350000
H2.5/14 2.50 14 14.0 8.0 2.2 4.2 0.15 0.25 10.0 l blue 500 9026100000
H4.0/17 4.00 12 17.0 10.0 2.8 4.8 0.2 0.3 12.0 l grey 250 9026010000
L2
L1
ø D1
S1
ø D2
S2
• Polypropylene conical cable entry
• Heat-resistant up to 105 °C
• Cable entry made from a not readily flammable material on request
For conductors from 0.14 to 150 mm2 (AWG 26-300MCM)
Tin-plated copper
Dimensional tolerances to DIN 46228 part 4
G.83
Accessories
G
Wire end ferrules with plastic collar
Weidmüller colour code Ordering data
Strip of wire end ferrules Type ø mm2AWG L1 L2 D1 D2 S1 S2
Stripping length
Colour Qty. Order No.
H0.5/14 0.50 20 14.0 8.0 1.0 2.6 0.15 0.25 10.0 l orange 500 9004270000
H0.75/14 0.75 18 14.0 8.0 1.2 2.8 0.15 0.25 10.0 m white 500 9004290000
H1.0/14 1.00 17 14.0 8.0 1.4 3.0 0.15 0.25 10.0 l yellow 500 9004320000
H1.5/14 1.50 16 14.0 8.0 1.7 3.2 0.15 0.25 10.0 l red 500 9004340000
H2.5/14D 2.50 14 14.0 8.0 2.2 4.0 0.15 0.25 11.0 l blue 500 9004360000
Weidmüller colour code Ordering data
Reel of wire end ferrules Type ø mm2AWG L1 L2 D1 D2 S1 S2
Stripping length
Colour Qty. Order No.
H0.34/12 0.34 22 12.0 8.0 0.8 2.0 0.15 0.25 10.0 l turquoise 5000 9004390000
H0.5/14 0.50 20 14.0 8.0 1.0 2.6 0.15 0.25 10.0 l orange 5000 9005810000
H0.75/14 0.75 18 14.0 8.0 1.2 2.8 0.15 0.25 10.0 m white 5000 9005820000
H1.0/14 1.00 17 14.0 8.0 1.4 3.0 0.15 0.25 11.0 l yellow 5000 9005830000
H1.5/14 1.50 16 14.0 8.0 1.7 3.2 0.15 0.25 10.0 l red 5000 9005840000
H2.5/14D 2.50 14 14.0 8.0 2.2 4.0 0.15 0.25 11.0 l blue 3000 9005850000
L2
L1
ø D1
S1
ø D2
S2
• Polypropylene conical cable entry
• Heat-resistant up to 105 °C
• Cable entry made from a not readily flammable material on request
For conductors from 0.5 to 2.5 mm2 (AWG 22-14)
Tin-plated copper
Dimensional tolerances to DIN 46228 part 4
G.84
Accessories
G
Wire end ferrules with plastic collar
DIN colour code Ordering data
packed loose Type ø mm2AWG L1 L2 D1 D2 S1 S2
Stripping length
Colour VG* Qty. Order No.
H0.5/12D 0.50 20 12.0 6.0 1.0 2.6 0.15 0.25 8.0 m white T 20A 001 A 500 9019000000
H0.5/14D 0.50 20 14.0 8.0 1.0 2.6 0.15 0.25 10.0 m white T 20A 002 A 500 9019010000
H0.5/16D 0.50 20 16.0 10.0 1.0 2.6 0.15 0.25 12.0 m white T 20A 003 A 500 9019020000
H0.75/12D 0.75 18 12.0 6.0 1.2 2.8 0.15 0.25 8.0 l grey T 20A 004 A 500 9019030000
H0.75/14D 0.75 18 14.0 8.0 1.2 2.8 0.15 0.25 10.0 l grey T 20A 005 A 500 9019040000
H0.75/16D 0.75 18 16.0 10.0 1.2 2.8 0.15 0.25 12.0 l grey T 20A 006 A 500 9019050000
H0.75/18D 0.75 18 18.0 12.0 1.2 2.8 0.15 0.25 14.0 l grey T 20A 007 A 500 9019060000
H1.0/12D 1.00 17 12.0 6.0 1.4 3.0 0.15 0.25 8.0 l red T 20A 008 A 500 9019070000
H1.0/14D 1.00 17 14.0 8.0 1.4 3.0 0.15 0.25 10.0 l red T 20A 009 A 500 9019080000
H1.0/16D 1.00 17 16.0 10.0 1.4 3.0 0.15 0.25 12.0 l red T 20A 010 A 500 9019100000
H1.0/18D 1.00 17 18.0 12.0 1.4 3.0 0.15 0.25 15.0 l red T 20A 011 A 500 9019110000
H1.5/14D 1.50 16 14.0 8.0 1.7 3.5 0.15 0.25 10.0 l black T 20A 012 A 500 9019120000
H1.5/16D 1.50 16 16.0 10.0 1.7 3.5 0.15 0.25 12.0 l black T 20A 013 A 500 9019130000
H1.5/18D 1.50 16 18.0 12.0 1.7 3.5 0.15 0.25 15.0 l black T 20A 014 A 500 9019140000
H1.5/24D 1.50 16 24.0 18.0 1.7 3.5 0.15 0.25 20.0 l black T 20A 015 A 500 9019150000
H2.5/14D 2.50 14 14.0 8.0 2.2 4.2 0.15 0.25 10.0 l blue T 20A 016 A 500 9019160000
H2.5/18D 2.50 14 18.0 12.0 2.2 4.2 0.15 0.25 14.0 l blue T 20A 017 A 500 9019170000
H2.5/24D 2.50 14 24.0 18.0 2.2 4.2 0.15 0.25 20.0 l blue T 20A 018 A 500 9019180000
H4.0/17D 4.00 12 17.0 10.0 2.8 4.8 0.2 0.3 12.0 l grey T 20A 019 A 500 9019190000
H4.0/20D 4.00 12 20.0 12.0 2.8 4.8 0.2 0.3 14.0 l grey T 20A 020 A 500 9019200000
H4.0/26D 4.00 12 26.0 18.0 2.8 4.8 0.2 0.3 20.0 l grey T 20A 021 A 100 9019210000
H6.0/20D 6.00 10 20.0 12.0 3.5 6.3 0.2 0.3 14.0 l yellow T 20A 022 A 100 9019220000
H6.0/26D 6.00 10 26.0 18.0 3.5 6.3 0.2 0.3 20.0 l yellow T 20A 023 A 100 9019230000
H10.0/22D 10.00 7 22.0 12.0 4.5 7.6 0.2 0.4 15.0 l red T 20A 024 A 100 9019240000
H10.0/28D 10.00 7 28.0 18.0 4.5 7.6 0.2 0.4 21.0 l red T 20A 025 A 100 9019250000
H16.0/24D 16.00 6 24.0 12.0 5.8 8.8 0.2 0.4 15.0 l blue T 20A 026 A 100 9019260000
H16.0/28D 16.00 6 28.0 18.0 5.8 8.8 0.2 0.4 21.0 l blue T 20A 027 A 100 9019270000
H25.0/30D 25.00 3 30.0 16.0 7.3 11.2 0.2 0.4 18.0 l yellow T 20A 028 A 50 9019280000
H25.0/36D 25.00 3 36.0 22.0 7.3 11.2 0.2 0.4 24.0 l yellow T 20A 030 A 50 9019300000
H35.0/30D 35.00 2 30.0 18.0 8.3 12.7 0.2 0.4 21.0 l red T 20A 032 A 50 9019320000
H35.0/30D 35.00 2 30.0 16.0 8.3 12.7 0.2 0.4 19.0 l red T 20A 031 A 50 9019310000
H35.0/39D 35.00 2 39.0 25.0 8.3 12.7 0.2 0.4 28.0 l red T 20A 033 A 50 9019330000
H50.0/36D 50.00 1 36.0 20.0 10.3 15.0 0.3 0.5 26.0 l blue T 20A 034 A 50 9019340000
H50.0/40D 50.00 1 40.0 25.0 10.3 15.0 0.3 0.5 31.0 l blue T 20A 035 A 50 9019350000
DIN colour code Ordering data
Iin multipack bag Type ø mm2AWG L1 L2 D1 D2 S1 S2
Stripping length
Colour VG* Qty. Order No.
H0.5/14D 0.50 20 14.0 8.0 1.0 2.6 0.15 0.25 10.0 m white T 20A 002 A 500 9019400000
H0.75/14D 0.75 18 14.0 8.0 1.2 2.8 0.15 0.25 10.0 l grey T 20A 005 A 500 9019410000
H1.0/14D 1.00 17 14.0 8.0 1.4 3.0 0.15 0.25 10.0 l red T 20A 009 A 500 9019420000
H1.5/14D 1.50 16 14.0 8.0 1.7 3.5 0.15 0.25 10.0 l black T 20A 012 A 500 9019430000
H1.5/24D 1.50 16 24.0 18.0 1.7 3.5 0.15 0.25 20.0 l black T 20A 015 A 500 9004140000
H2.5/14 2.50 14 14.0 8.0 2.2 4.2 0.15 0.25 10.0 l blue 500 9026100000
H4.0/17 4.00 12 17.0 10.0 2.8 4.8 0.2 0.3 12.0 l grey 250 9026010000
DIN colour code Ordering data
Strip of wire end ferrules Type ø mm2AWG L1 L2 D1 D2 S1 S2
Stripping length
Colour Qty. Order No.
H0.5/14D 0.50 20 14.0 8.0 1.0 2.6 0.15 0.25 10.0 m white T 20A 002 A 500 9004280000
H0.75/14D 0.75 18 14.0 8.0 1.2 2.8 0.15 0.25 10.0 l grey T 20A 005 A 500 9004300000
H1.0/14D 1.00 17 14.0 8.0 1.4 3.0 0.15 0.25 10.0 l red T 20A 009 A 500 9004330000
H1.5/14D 1.50 16 14.0 8.0 1.7 3.2 0.15 0.25 10.0 l black T 20A 012 A 500 9004350000
H2.5/14D 2.50 14 14.0 8.0 2.2 4.0 0.15 0.25 11.0 l blue T 20A 016 A 500 9004360000
L2
L1
ø D1
S1
ø D2
S2
• Polypropylene conical cable entry
• Heat-resistant up to 105 °C
• Cable entry made from a not readily flammable material on request
For conductors from 0.5 to 50 mm2 (AWG 20-1)
Tin-plated copper
Dimensional tolerances to DIN 46228 part 4
G.85
Accessories
G
Wire end ferrules with plastic collar
DIN colour code Ordering data
Reel of wire end ferrules Type ø mm2AWG L1 L2 D1 D2 S1 S2
Stripping length
Colour VG* Qty. Order No.
H0.5/14D 0.50 20 14.0 8.0 1.0 2.6 0.15 0.25 10.0 m white 5000 9005860000
H0.75/14 0.75 18 14.0 8.0 1.2 2.8 0.15 0.25 10.0 l grey 5000 9005870000
H1.0/14D 1.00 17 14.0 8.0 1.4 3.0 0.15 0.25 11.0 l red 5000 9005880000
H1.5/14D 1.50 16 14.0 8.0 1.7 3.2 0.15 0.25 10.0 l black 5000 9005890000
H2.5/14D 2.50 14 14.0 8.0 2.2 4.0 0.15 0.25 11.0 l blue 3000 9005850000
L2
L1
ø D1
S1
ø D2
S2
• Polypropylene conical cable entry
• Heat-resistant up to 105 °C
• Cable entry made from a not readily flammable material on request
For conductors from 0.5 to 2.5 mm2 (AWG 20-14)
Tin-plated copper
Dimensional tolerances to DIN 46228 part 4
G.86
Accessories
G
Wire end ferrules with plastic collar
other colour code Ordering data
packed loose Type ø mm2AWG L1 L2 D1 D2 S1 S2
Stripping length
Colour Qty. Order No.
H0.25/10T 0.25 24 10.0 6.0 0.8 1.8 0.15 0.25 8.0 l yellow 500 9021010000
H0.25/12T 0.25 24 12.0 8.0 0.8 1.8 0.15 0.25 10.0 l yellow 500 9021020000
H0.5/12D 0.50 20 12.0 6.0 1.0 2.6 0.15 0.25 8.0 m white 500 9019000000
H0.5/14D 0.50 20 14.0 8.0 1.0 2.6 0.15 0.25 10.0 m white 500 9019010000
H0.5/16D 0.50 20 16.0 10.0 1.0 2.6 0.15 0.25 12.0 m white 500 9019020000
H0.75/12T 0.75 18 12.0 6.0 1.2 2.8 0.15 0.25 8.0 l light blue 500 9021030000
H0.75/14 0.75 18 14.0 8.0 1.2 2.8 0.15 0.25 10.0 l light blue 500 9021040000
H0.75/16T 0.75 18 16.0 10.0 1.2 2.8 0.15 0.25 12.0 l light blue 500 9021050000
H0.75/18T 0.75 18 18.0 12.0 1.2 2.8 0.15 0.25 14.0 l light blue 500 9021060000
H1.0/12D 1.00 17 12.0 6.0 1.4 3.0 0.15 0.25 8.0 l red 500 9019070000
H1.0/14D 1.00 17 14.0 8.0 1.4 3.0 0.15 0.25 10.0 l red 500 9019080000
H1.0/16D 1.00 17 16.0 10.0 1.4 3.0 0.15 0.25 12.0 l red 500 9019100000
H1.0/18D 1.00 17 18.0 12.0 1.4 3.0 0.15 0.25 15.0 l red 500 9019110000
H1.5/14D 1.50 16 14.0 8.0 1.7 3.5 0.15 0.25 10.0 l black 500 9019120000
H1.5/16D 1.50 16 16.0 10.0 1.7 3.5 0.15 0.25 12.0 l black 500 9019130000
H1.5/18D 1.50 16 18.0 12.0 1.7 3.5 0.15 0.25 15.0 l black 500 9019140000
H1.5/24D 1.50 16 24.0 18.0 1.7 3.5 0.15 0.25 20.0 l black 500 9019150000
H2.5/14T 2.50 14 14.0 8.0 2.2 4.2 0.15 0.25 10.0 l grey 500 9021070000
H2.5/18T 2.50 14 18.0 12.0 2.2 4.2 0.15 0.25 14.0 l grey 500 9021080000
H2.5/24T 2.50 14 24.0 18.0 2.2 4.2 0.15 0.25 20.0 l grey 500 9021090000
H4.0/17T 4.00 12 17.0 10.0 2.8 4.8 0.2 0.3 12.0 l orange 500 9021100000
H4.0/20T 4.00 12 20.0 12.0 2.8 4.8 0.2 0.3 14.0 l orange 500 9021110000
H4.0/26T 4.00 12 26.0 18.0 2.8 4.8 0.2 0.3 20.0 l orange 100 9021120000
H6.0/20T 6.00 10 20.0 12.0 3.5 6.3 0.2 0.3 14.0 l green 100 9021130000
H6.0/26T 6.00 10 26.0 18.0 3.5 6.3 0.2 0.3 20.0 l green 100 9021140000
H10.0/22T 10.00 7 22.0 12.0 4.5 7.6 0.2 0.4 15.0 l brown 100 9021150000
H10.0/28T 10.00 7 28.0 18.0 4.5 7.6 0.2 0.4 21.0 l brown 100 9021160000
H16.0/24T 16.00 6 24.0 12.0 5.8 8.8 0.2 0.4 15.0 m white 100 9021170000
H16.0/28T 16.00 6 28.0 18.0 5.8 8.8 0.2 0.4 21.0 m white 100 9021180000
H25.0/30T 25.00 3 30.0 16.0 7.3 11.2 0.2 0.4 18.0 l black 50 9021190000
H25.0/36T 25.00 3 36.0 22.0 7.3 11.2 0.2 0.4 24.0 l black 50 9021200000
other colour code Ordering data
Iin multipack bag Type ø mm2AWG L1 L2 D1 D2 S1 S2
Stripping length
Colour Qty. Order No.
H0.14/10T 0.14 26 10.0 6.0 0.6 1.5 0.15 0.25 8.0 l brown 500 9028250000
H0.25/10T 0.25 24 10.0 6.0 0.8 1.8 0.15 0.25 8.0 l yellow 500 9021210000
H0.25/12T 0.25 24 12.0 8.0 0.8 1.8 0.15 0.25 10.0 l yellow 500 9021220000
H0.5/14D 0.50 20 14.0 8.0 1.0 2.6 0.15 0.25 10.0 m white 500 9019400000
H0.75/14T 0.75 18 14.0 8.0 1.2 2.8 0.15 0.25 10.0 l light blue 500 9021230000
H1.0/14D 1.00 17 14.0 8.0 1.4 3.0 0.15 0.25 10.0 l red 500 9019420000
H1.5/14D 1.50 16 14.0 8.0 1.7 3.5 0.15 0.25 10.0 l black 500 9019430000
H1.5/24D 1.50 16 24.0 18.0 1.7 3.5 0.15 0.25 20.0 l black 500 9004140000
H2.5/14T 2.50 14 14.0 8.0 2.2 4.2 0.15 0.25 10.0 l grey 500 9021240000
H4.0/17T 4.00 12 17.0 10.0 2.8 4.8 0.2 0.3 12.0 l orange 250 9021250000
other colour code Ordering data
Strip of wire end ferrules Type ø mm2AWG L1 L2 D1 D2 S1 S2
Stripping length
Colour Qty. Order No.
H0.5/14D 0.50 20 14.0 8.0 1.0 2.6 0.15 0.25 10.0 m white 500 9004280000
H0.75/14T 0.75 18 14.0 8.0 1.2 2.8 0.15 0.25 10.0 l light blue 500 9004310000
H1.0/14D 1.00 17 14.0 8.0 1.4 3.0 0.15 0.25 10.0 l red 500 9004330000
H1.5/14D 1.50 16 14.0 8.0 1.7 3.2 0.15 0.25 10.0 l black 500 9004350000
H2.5/14T 2.50 14 14.0 8.0 2.2 4.0 0.15 0.25 11.0 l grey 500 9004370000
L2
L1
ø D1
S1
ø D2
S2
• Polypropylene conical cable entry
• Heat-resistant up to 105 °C
• Cable entry made from a not readily flammable material on request
For conductors from 0.14 to 25 mm2 (AWG 26-3)
Tin-plated copper
Dimensional tolerances to DIN 46228 part 4
G.87
Accessories
G
Wire end ferrules with plastic collar
other colour code Ordering data
Reel of wire end ferrules Type ø mm2AWG L1 L2 D1 D2 S1 S2
Stripping length
Colour Qty. Order No.
H0.5/14D 0.50 20 14.0 8.0 1.0 2.6 0.15 0.25 10.0 m white 5000 9005860000
H0.75/14T 0.75 18 14.0 8.0 1.2 2.8 0.15 0.25 10.0 l light blue 5000 9005900000
H1.0/14D 1.00 17 14.0 8.0 1.4 3.0 0.15 0.25 11.0 l red 5000 9005880000
H1.5/14D 1.50 16 14.0 8.0 1.7 3.2 0.15 0.25 10.0 l black 5000 9005890000
H2.5/14T 2.50 14 14.0 8.0 2.2 4.0 0.15 0.25 11.0 l grey 3000 9005910000
L2
L1
ø D1
S1
ø D2
S2
• Polypropylene conical cable entry
• Heat-resistant up to 105 °C
• Cable entry made from a not readily flammable material on request
For conductors from 0.5 to 2.5 mm2 (AWG 20-14)
Tin-plated copper
Dimensional tolerances to DIN 46228 part 4
G.88
Accessories
G
Twin-wire end ferrules with plastic collar
Weidmüller colour code Ordering data
packed loose Type ø mm2AWG L1 L2 D1 D2 S1 S2
Stripping length
Colour Qty. Order No.
H0.5/15 0.50 20 15.0 8.0 1.4 0.15 0.3 11.0 l orange 500 9037200000
H0.5/16.5 0.50 20 16.0 10.0 1.4 0.15 0.3 13.0 l orange 500 9037210000
H0.5/18.5 0.50 20 19.0 12.0 1.4 0.15 0.3 15.0 l orange 500 9037220000
H0.75/15 0.75 18 15.0 8.0 1.7 0.15 0.3 11.0 m white 500 9037230000
H0.75/17 0.75 18 17.0 10.0 1.7 0.15 0.3 13.0 m white 500 9037240000
H0.75/19S 0.75 18 19.0 12.0 1.4 0.15 0.3 21.0 m white 500 9202820000
H0.75/24.5 0.75 18 24.0 18.0 1.7 0.15 0.3 21.0 m white 500 9037250000
H1.0/15 1.00 17 15.0 8.0 2.0 0.15 0.3 12.0 l yellow 500 9037260000
H1.0/15S 1.00 17 16.0 8.0 2.2 0.15 0.3 12.0 l yellow 500 9018690000
H1.0/20 1.00 17 19.0 12.0 2.0 0.15 0.3 16.0 l yellow 500 9037270000
H1.0/25.6 1.00 17 25.0 18.0 2.0 0.15 0.3 22.0 l yellow 500 9037280000
H1.5/16 1.50 16 16.0 8.2 2.2 0.15 0.3 11.0 l red 500 9037290000
H1.5/20 1.50 16 20.0 12.0 2.2 0.15 0.3 15.0 l red 500 9037300000
H1.5/25.6 1.50 16 26.0 18.0 2.2 0.15 0.3 21.0 l red 100 9037310000
H2.5/18.5D 2.50 14 19.0 10.0 2.8 0.15 0.4 13.0 l blue 500 9037500000
H2.5/20.5D 2.50 14 21.0 12.0 2.8 0.15 0.4 15.0 l blue 100 9037510000
H2.5/26.5D 2.50 14 27.0 18.0 2.8 0.15 0.4 21.0 l blue 100 9037520000
H4.0/22D 4.00 12 22.0 12.0 3.5 0.2 0.5 15.0 l grey 100 9037530000
H4.0/28D 4.00 12 28.0 18.0 3.5 0.2 0.5 21.0 l grey 100 9037540000
H6.0/25 6.00 10 25.0 12.0 4.5 0.2 0.5 20.0 l black 100 9037320000
H6.0/29 6.00 10 29.0 18.0 4.5 0.2 0.5 24.0 l black 100 9037330000
H10.0/24S 10.00 7 24.0 12.0 6.5 0.2 0.5 17.0 l ivory 100 9018860000
H10.0/26 10.00 7 24.0 12.0 5.8 0.2 0.5 17.0 l ivory 100 9037340000
H10.0/30 10.00 7 30.0 18.0 5.8 0.2 0.5 23.0 l ivory 100 9037350000
H10.0/30S 10.00 7 30.0 18.0 6.5 0.2 0.5 23.0 l ivory 100 9018870000
H16.0/29 16.00 6 29.0 16.0 8.3 0.3 0.6 20.0 l green 50 9037360000
H16.0/38 16.00 6 38.0 25.0 8.3 0.3 0.6 29.0 l green 50 9037370000
Weidmüller colour code Ordering data
Iin multipack bag Type ø mm2AWG L1 L2 D1 D2 S1 S2
Stripping length
Colour Qty. Order No.
H0.5/15 0.50 20 15.0 8.0 1.4 0.15 0.3 11.0 l orange 500 9004440000
H0.75/15 0.75 18 15.0 8.0 1.7 0.15 0.3 11.0 m white 500 9018510000
H0.75/17 0.75 18 17.0 10.0 1.7 0.15 0.3 13.0 m white 500 9004900000
H1.0/15 1.00 17 15.0 8.0 2.0 0.15 0.3 12.0 l yellow 500 9018530000
H1.0/15S 1.00 17 16.0 8.0 2.2 0.15 0.3 12.0 l yellow 500 9018650000
H1.0/20 1.00 17 19.0 12.0 2.0 0.15 0.3 16.0 l yellow 500 9004910000
H1.5/16 1.50 16 16.0 8.2 2.2 0.15 0.3 11.0 l red 500 9004410000
H1.5/20 1.50 16 20.0 12.0 2.2 0.15 0.3 15.0 l red 500 9004920000
H2.5/18.5D 2.50 14 19.0 10.0 2.8 0.15 0.4 13.0 l blue 250 9004430000
H2.5/20.5D 2.50 14 21.0 12.0 2.8 0.15 0.4 15.0 l blue 250 9004740000
H4.0/22D 4.00 12 22.0 12.0 3.5 0.2 0.5 15.0 l grey 100 9004730000
H6.0/25 6.00 10 25.0 12.0 4.5 0.2 0.5 20.0 l black 100 9004930000
H10.0/26 10.00 7 24.0 12.0 5.8 0.2 0.5 17.0 l ivory 100 9004940000
L2
L1
D1
S2
S1
B
A
• Polypropylene conical cable entry
• Heat-resistant up to 105 °C
• Cable entry made from a not readily flammable material on request
For conductors from 2 x 0,5-2 x 16 mm2 (2 x AWG 20-2 x AWG 6)
Tin-plated copper
Dimensional tolerances to DIN 46228 part 4
G.89
Accessories
G
Twin-wire end ferrules with plastic collar
DIN colour code Ordering data
packed loose Type ø mm2AWG L1 L2 D1 D2 S1 S2
Stripping length
Colour Qty. Order No.
H0.5/15D 0.50 20 15.0 8.0 1.4 0.15 0.3 11.0 m white 500 9037380000
H0.5/16.5D 0.50 20 16.0 10.0 1.4 0.15 0.3 13.0 m white 500 9037390000
H0.5/18.4D 0.50 20 19.0 12.0 1.4 0.15 0.3 15.0 m white 500 9037400000
H0.75/15D 0.75 18 15.0 8.0 1.7 0.15 0.3 11.0 l grey 500 9037410000
H0.75/17D 0.75 18 17.0 10.0 1.7 0.15 0.3 13.0 l grey 500 9037420000
H0.75/19DS 0.75 18 19.0 12.0 1.4 0.15 0.3 21.0 l grey 500 9202830000
H0.75/24.5D 0.75 18 24.0 18.0 1.7 0.15 0.3 21.0 l grey 500 9037430000
H1.0/15D 1.00 17 16.0 8.0 2.2 0.15 0.3 12.0 l red 500 9037440000
H1.0/20D 1.00 17 19.0 12.0 2.0 0.15 0.3 16.0 l red 500 9037450000
H1.0/25.6D 1.00 17 25.0 18.0 2.0 0.15 0.3 22.0 l red 500 9037460000
H1.5/16D 1.50 16 16.0 8.0 2.2 0.15 0.3 11.0 l black 500 9037470000
H1.5/20D 1.50 16 20.0 12.0 2.2 0.15 0.3 15.0 l black 500 9037480000
H1.5/25.6D 1.50 16 26.0 18.0 2.2 0.15 0.3 21.0 l black 100 9037490000
H2.5/18.5D 2.50 14 19.0 10.0 2.8 0.15 0.4 13.0 l blue 500 9037500000
H2.5/20.5D 2.50 14 21.0 12.0 2.8 0.15 0.4 15.0 l blue 100 9037510000
H2.5/26.5D 2.50 14 27.0 18.0 2.8 0.15 0.4 21.0 l blue 100 9037520000
H4.0/22D 4.00 12 22.0 12.0 3.5 0.2 0.5 15.0 l grey 100 9037530000
H4.0/28D 4.00 12 28.0 18.0 3.5 0.2 0.5 21.0 l grey 100 9037540000
H6.0/25D 6.00 10 25.0 12.0 4.5 0.2 0.5 20.0 l yellow 100 9037550000
H6.0/29D 6.00 10 29.0 18.0 4.5 0.2 0.5 24.0 l yellow 100 9037560000
H10.0/24DS 10.00 7 24.0 12.0 6.5 0.2 0.5 17.0 l red 100 9018880000
H10.0/26D 10.00 7 24.0 12.0 5.8 0.2 0.5 17.0 l red 100 9037570000
H10.0/30D 10.00 7 30.0 18.0 5.8 0.2 0.5 23.0 l red 100 9037580000
H10.0/30DS 10.00 7 30.0 18.0 6.5 0.2 0.5 23.0 l red 100 9018890000
H16.0/29D 16.00 6 29.0 16.0 8.3 0.3 0.6 20.0 l blue 50 9037590000
H16.0/38D 16.00 6 38.0 25.0 8.3 0.3 0.6 29.0 l blue 50 9037600000
DIN colour code Ordering data
Iin multipack bag Type ø mm2AWG L1 L2 D1 D2 S1 S2
Stripping length
Colour Qty. Order No.
H0.5/15D 0.50 20 15.0 8.0 1.4 0.15 0.3 11.0 m white 500 9004780000
H0.75/15D 0.75 18 15.0 8.0 1.7 0.15 0.3 11.0 l grey 500 9018520000
H0.75/17D 0.75 18 17.0 10.0 1.7 0.15 0.3 13.0 l grey 500 9004770000
H1.0/15D 1.00 17 16.0 8.0 2.2 0.15 0.3 12.0 l red 500 9018540000
H1.0/20D 1.00 17 19.0 12.0 2.0 0.15 0.3 16.0 l red 500 9004760000
H1.5/16D 1.50 16 16.0 8.0 2.2 0.15 0.3 11.0 l black 500 9004420000
H1.5/20D 1.50 16 20.0 12.0 2.2 0.15 0.3 15.0 l black 500 9004750000
H2.5/18.5D 2.50 14 19.0 10.0 2.8 0.15 0.4 13.0 l blue 250 9004430000
H2.5/20.5D 2.50 14 21.0 12.0 2.8 0.15 0.4 15.0 l blue 250 9004740000
H4.0/22D 4.00 12 22.0 12.0 3.5 0.2 0.5 15.0 l grey 100 9004730000
H6.0/25D 6.00 10 25.0 12.0 4.5 0.2 0.5 20.0 l yellow 100 9004720000
H10.0/26D 10.00 7 24.0 12.0 5.8 0.2 0.5 17.0 l red 100 9004710000
L2
L1
D1
S2
S1
B
A
• Polypropylene conical cable entry
• Heat-resistant up to 105 °C
• Cable entry made from a not readily flammable material on request
For conductors from 2 x 0,5-2 x 16 mm2 (2 x AWG 20-2 x AWG 6)
Tin-plated copper
Dimensional tolerances to DIN 46228 part 4
G.90
Accessories
G
Twin-wire end ferrules with plastic collar
other colour code Ordering data
packed loose Type ø mm2AWG L1 L2 D1 D2 S1 S2
Stripping length
Colour Qty. Order No.
H0.5/15 0.50 20 15.0 8.0 1.4 0.15 0.3 11.0 l orange 500 9037200000
H0.5/16.5 0.50 20 16.0 10.0 1.4 0.15 0.3 13.0 l orange 500 9037210000
H0.5/18.5 0.50 20 19.0 12.0 1.4 0.15 0.3 15.0 l orange 500 9037220000
H0.75/15T 0.75 18 15.0 8.0 1.7 0.15 0.3 11.0 l light blue 500 9037610000
H0.75/17T 0.75 18 17.0 10.0 1.7 0.15 0.3 13.0 l light blue 500 9037620000
H0.75/19TS 0.75 18 19.0 12.0 1.4 0.15 0.3 21.0 l light blue 500 9202840000
H0.75/24.5T 0.75 18 24.0 18.0 1.7 0.15 0.3 21.0 l light blue 500 9037630000
H1.0/15D 1.00 17 16.0 8.0 2.2 0.15 0.3 12.0 l red 500 9037440000
H1.0/20D 1.00 17 19.0 12.0 2.0 0.15 0.3 16.0 l red 500 9037450000
H1.0/25.6D 1.00 17 25.0 18.0 2.0 0.15 0.3 22.0 l red 500 9037460000
H1.5/16D 1.50 16 16.0 8.0 2.2 0.15 0.3 11.0 l black 500 9037470000
H1.5/20D 1.50 16 20.0 12.0 2.2 0.15 0.3 15.0 l black 500 9037480000
H1.5/25.6D 1.50 16 26.0 18.0 2.2 0.15 0.3 21.0 l black 100 9037490000
H2.5/18.5T 2.50 14 19.0 10.0 2.8 0.15 0.4 13.0 l grey 500 9037640000
H2.5/20.5T 2.50 14 21.0 12.0 2.8 0.15 0.4 15.0 l grey 100 9037650000
H2.5/26.5T 2.50 14 27.0 18.0 2.8 0.15 0.4 21.0 l grey 100 9037660000
H4.0/22T 4.00 12 22.0 12.0 3.5 0.2 0.5 15.0 l orange 100 9037670000
H4.0/28T 4.00 12 28.0 18.0 3.5 0.2 0.5 21.0 l orange 100 9037680000
H6.0/25T 6.00 10 25.0 12.0 4.5 0.2 0.5 20.0 l green 100 9037690000
H6.0/29T 6.00 10 29.0 18.0 4.5 0.2 0.5 24.0 l green 100 9037700000
H10.0/26T 10.00 7 24.0 12.0 5.8 0.2 0.5 17.0 l brown 100 9037710000
H10.0/30T 10.00 7 30.0 18.0 5.8 0.2 0.5 23.0 l brown 100 9037720000
H16.0/19T 16.00 6 29.0 16.0 8.3 0.3 0.6 20.0 m white 50 9037730000
H16.0/38T 16.00 6 38.0 25.0 8.3 0.3 0.6 29.0 m white 50 9037740000
other colour code Ordering data
Iin multipack bag Type ø mm2AWG L1 L2 D1 D2 S1 S2
Stripping length
Colour Qty. Order No.
H0.75/17T 0.75 18 17.0 10.0 1.7 0.15 0.3 13.0 l light blue 500 9005140000
H1.0/15D 1.00 17 16.0 8.0 2.2 0.15 0.3 12.0 l red 500 9018540000
H1.0/20D 1.00 17 19.0 12.0 2.0 0.15 0.3 16.0 l red 500 9004760000
H1.5/16D 1.50 16 16.0 8.0 2.2 0.15 0.3 11.0 l black 500 9004420000
H1.5/20D 1.50 16 20.0 12.0 2.2 0.15 0.3 15.0 l black 500 9004750000
H2.5/18.5T 2.50 14 19.0 10.0 2.8 0.15 0.4 13.0 l grey 250 9018580000
H2.5/20.5 2.50 14 21.0 12.0 2.8 0.15 0.4 15.0 l grey 250 9005150000
H4.0/22T 4.00 12 22.0 12.0 3.5 0.2 0.5 15.0 l orange 100 9018590000
H6.0/25T 6.00 10 25.0 12.0 4.5 0.2 0.5 20.0 l green 100 9005160000
H10.0/26T 10.00 7 24.0 12.0 5.8 0.2 0.5 17.0 l brown 100 9005170000
• Polypropylene conical cable entry
• Heat-resistant up to 105 °C
• Cable entry made from a not readily flammable material on request
For conductors from 2 x 0,5-2 x 16 mm2 (2 x AWG 20-2 x AWG 6)
Tin-plated copper
Dimensional tolerances to DIN 46228 part 4
L2
L1
D1
S2
S1
B
A
G.91
Accessories
G
Wire end ferrules for short-circuit and earth-fault-proof cables
Weidmüller colour code Ordering data
packed loose Type ø mm2AWG L1 L2 D1 D2 S1 S2
Stripping length
Colour Qty. Order No.
H1.5/24 XS 1.50 16 24.0 18.0 1.8 6.8 0.15 0.3 20.0 l black 100 9202870000
H2.5/24 XS 2.50 14 24.0 18.0 2.3 7.6 0.15 0.3 20.0 l blue 100 9202880000
Weidmüller colour code Ordering data
Iin multipack bag Type ø mm2AWG L1 L2 D1 D2 S1 S2
Stripping length
Colour Qty. Order No.
H1.5/17.5X 1.50 16 17.5 8.0 1.8 6.8 0.15 0.3 13.0 l black 100 9006590000
H1.5/19.5X 1.50 16 19.5 10.0 1.8 6.8 0.15 0.3 15.0 l black 100 9006630000
H2.5/17.5X 2.50 14 17.5 8.0 2.3 7.6 0.15 0.3 14.0 l blue 100 9006670000
H2.5/21.5X 2.50 14 21.5 12.0 2.3 7.6 0.15 0.3 17.0 l blue 100 9006710000
H4.0/19.5X 4.00 12 19.5 10.0 2.9 7.8 0.2 0.3 14.0 l grey 100 9006750000
H6.0/23.0X 6.00 10 23.0 12.0 3.6 8.1 0.2 0.3 17.0 l yellow 100 9006790000
H10.0/24.5X 10.00 7 24.0 12.0 4.6 9.6 0.2 0.3 17.0 l red 100 9006830000
H16.0/25.5X 16.00 6 25.5 12.0 6.0 11.9 0.2 0.3 26.0 l blue 100 9006870000
L2
L1
ø D1
S1
ø D2
S2
• Polypropylene conical cable entry
• Heat-resistant up to 105 °C
• Cable entry made from a not readily flammable material on request
For conductors from 1.5 to 16 mm2 (AWG 16-6)
Tin-plated copper
Dimensional tolerances to DIN 46228 part 4
G.92
Accessories
G
Wire end ferrules with plastic collar, special sizes
Weidmüller colour code Ordering data
packed loose Type ø mm2AWG L1 L2 D1 D2 S1 S2
Stripping length
Colour Qty. Order No.
H0.5/14S 0.50 20 14.0 8.0 1.0 2.9 0.15 0.25 10.0 l orange 500 9004560000
H0.5/14S 0.50 20 14.0 8.0 1.0 2.9 0.15 0.25 10.0 m white 500 9004590000
H0.5/16DS 0.50 20 16.0 10.0 1.0 2.9 0.15 0.25 12.0 m white 500 9202910000
H0.5/16S 0.50 20 16.0 10.0 1.0 2.9 0.15 0.25 12.0 l orange 500 9202900000
H0.75/14S 0.75 18 14.0 8.0 1.2 3.4 0.15 0.25 10.0 m white 500 9025960000
H0.75/14TS 0.75 18 14.0 8.0 1.2 3.4 0.15 0.25 10.0 l light blue 500 9018550000
H1.0/14S 1.00 17 14.0 8.0 1.4 3.5 0.15 0.25 10.0 l yellow 500 9025970000
H1.0/14S 1.00 17 14.0 8.0 1.4 3.5 0.15 0.25 10.0 l red 500 9018560000
H1.5/12S 1.50 16 12.0 6.0 1.7 3.5 0.15 0.25 8.0 l red 500 9025690000
H1.5/14S 1.50 16 14.0 8.0 1.7 3.9 0.15 0.25 10.0 l red 500 9025980000
H1.5/14S 1.50 16 14.0 8.0 1.7 3.9 0.15 0.25 10.0 l black 500 9025240000
H2.5/12DS 2.50 14 12.0 6.0 2.2 4.2 0.15 0.25 8.0 l blue 500 9028490000
H2.5/12TS 2.50 14 12.0 6.0 2.2 4.2 0.15 0.25 8.0 l grey 500 9036200000
H2.5/14S 2.50 14 14.0 8.0 2.2 4.0 0.15 0.25 10.0 l blue 500 1333100000
H2.5/14TS 2.50 14 14.0 8.0 2.2 4.0 0.15 0.25 10.0 l grey 500 9426770000
H2.5/16DS 2.50 14 16.0 10.0 2.2 4.2 0.15 0.25 13.0 l blue 500 9036220000
Weidmüller colour code Ordering data
Iin multipack bag Type ø mm2AWG L1 L2 D1 D2 S1 S2
Stripping length
Colour Qty. Order No.
H0.75/14S 0.75 18 14.0 8.0 1.2 3.4 0.15 0.25 10.0 m white 500 9025700000
H1.0/14S 1.00 17 14.0 8.0 1.4 3.5 0.15 0.25 10.0 l yellow 500 9025710000
H1.5/14DS 1.50 16 14.0 8.0 1.7 3.9 0.15 0.25 10.0 l black 500 9028360000
H1.5/14S 1.50 16 14.0 8.0 1.7 3.9 0.15 0.25 10.0 l red 500 9025720000
L2
L1
ø D1
S1
ø D2
S2
• Polypropylene conical cable entry
• Heat-resistant up to 105 °C
• Cable entry made from a not readily flammable material on request
For conductors from 0.5 to 2.5 mm2 (AWG 20-14)
Tin-plated copper
Dimensional tolerances to DIN 46228 part 4
G.93
Accessories
G
Wire end ferrules without plastic collar
without plastic collar Ordering data
packed loose Type ø mm2AWG L1 L2 D1 D2 S1 S2
Stripping length
Colour Qty. Order No.
H0.25/5 0.25 24 5.0 0.7 1.6 5.0 1000 9018910000
H0.5/10 0.50 20 10.0 1.0 2.1 10.0 1000 9004050000
H0.5/6 0.50 20 6.0 1.0 2.1 6.0 1000 0282600000
H0.75/10 0.75 18 10.0 1.2 2.3 10.0 1000 0542500000
H0.75/6 0.75 18 6.0 1.2 2.3 6.0 1000 0282700000
H1.0/10 1.00 17 10.0 1.4 2.5 10.0 1000 0282800000
H1.0/6 1.00 17 6.0 1.4 2.5 6.0 1000 0372600000
H1.5/7 1.50 16 7.0 1.7 2.8 7.0 1000 0372700000
H1.5/10 1.50 16 10.0 1.7 2.8 10.0 1000 0186500000
H1.5/12 1.50 16 12.0 1.7 2.8 12.0 1000 9004060000
H1.5/18 1.50 16 18.0 1.7 2.8 18.0 1000 9004070000
H2.5/7 2.50 14 7.0 2.2 3.4 7.0 1000 0373000000
H2.5/10 2.50 14 10.0 2.2 3.4 10.0 1000 9004080000
H2.5/12 2.50 14 12.0 2.2 3.4 12.0 1000 0186100000
H2.5/18 2.50 14 18.0 2.2 3.4 18.0 1000 9004090000
H4.0/9 4.00 12 9.0 2.8 4.0 9.0 500 0373100000
H4.0/15 4.00 12 15.0 2.8 4.0 15.0 500 9004100000
H4.0/12 4.00 12 12.0 2.8 4.0 12.0 1000 0244100000
H4.0/18 4.00 12 18.0 2.8 4.0 18.0 500 9004110000
H6.0/10 6.00 10 10.0 3.5 4.7 10.0 500 9004120000
H6.0/12 6.00 10 12.0 3.5 4.7 12.0 500 0191900000
H6.0/15 6.00 10 15.0 3.5 4.7 15.0 500 0124700000
H6.0/18 6.00 10 18.0 3.5 4.7 18.0 500 9004130000
H10.0/12 10.00 7 12.0 4.5 5.8 12.0 500 0282900000
H10.0/15 10.00 7 15.0 4.5 5.8 15.0 500 0124800000
H10.0/18 10.00 7 18.0 4.5 5.8 18.0 500 0379300000
H16.0/12 16.00 6 12.0 5.8 7.5 12.0 500 0492500000
H16.0/15 16.00 6 15.0 5.8 7.5 15.0 500 0124300000
H16.0/18 16.00 6 18.0 5.8 7.5 18.0 100 0375200000
H16.0/25 16.00 6 25.0 5.8 7.5 25.0 100 9004150000
H16.0/32 16.00 6 32.0 5.8 7.5 32.0 100 9004160000
H25.0/15 25.00 3 15.0 7.3 9.5 15.0 250 0124400000
H25.0/18 25.00 3 18.0 7.3 9.5 18.0 100 0375300000
H25.0/25 25.00 3 25.0 7.3 9.5 25.0 250 9004170000
H25.0/32 25.00 3 32.0 7.3 9.5 32.0 100 9004180000
H35.0/18 35.00 2 18.0 8.3 11.0 18.0 100 0368900000
H35.0/25 35.00 2 25.0 8.3 11.0 25.0 100 9004190000
H35.0/30 35.00 2 30.0 8.3 11.0 30.0 100 9451000000
H35.0/32 35.00 2 32.0 8.3 11.0 32.0 100 9004200000
H50.0/18 50.00 1 18.0 10.3 13.0 18.0 100 9004210000
H50.0/25 50.00 1 25.0 10.3 13.0 25.0 100 9025880000
H50.0/32 50.00 1 32.0 10.3 13.0 32.0 100 9004220000
H70.0/25 70.00 2/0 25.0 12.5 15.0 25.0 50 9004230000
H70.0/32 70.00 2/0 32.0 12.5 15.0 32.0 50 9004240000
H95.0/25 95.00 3/0 25.0 14.5 17.0 25.0 50 9004250000
H95.0/32 95.00 3/0 32.0 14.5 17.0 32.0 50 9004260000
H120.0/32 120.00 4/0 32.0 16.5 19.0 32.0 25 9036240000
H150.0/32 150.00 300 MCM 32.0 18.5 21.0 32.0 25 9036250000
H185.0/32 185.00 350 MCM 32.0 20.0 23.5 32.0 25 9036260000
For conductors 0.25-185 mm2 (AWG 24-350MCM)
Material: tin-plated copper
Dimensional tolerances to DIN 46228 part 1
G.94
Accessories
G
Insulated cable connectors, PVC, with conical cable entry
Ring cable connector Ordering data
Type Cross-section, mm2Colour Dimensions Qty. Order No.
LIR 1.5M3 V 0.5 - 1.5 l M 3 100 9200070000
LIR 1.5M3.5 V 0.5 - 1.5 l M 3.5 100 9200080000
LIR 1.5M4 V 0.5 - 1.5 l M 4 100 9200090000
LIR 1.5M5 V 0.5 - 1.5 l M 5 100 9200100000
LIR 1.5M6 V 0.5 - 1.5 l M 6 100 9200110000
LIR 1.5M8 V 0.5 - 1.5 l M 8 100 9200120000
LIR 2.5M3 V 1.5 - 2.5 l M 3 100 9200150000
LIR 2.5M3.5 V 1.5 - 2.6 l M 3.5 100 9200160000
LIR 2.5M4 V 1.5 - 2.7 l M 4 100 9200170000
LIR 2.5M5 V 1.5 - 2.8 l M 5 100 9200180000
LIR 2.5M6 V 1.5 - 2.9 l M 6 100 9200190000
LIR 2.5M8 V 1.5 - 2.1 l M 8 100 9200200000
LIR 2.5M10 V 1.5 - 2.5 l M 10 100 9200210000
LIR 6.0M4 V 4 - 6 l M 4 100 9200230000
LIR 6M5 V 4 - 6 l M 5 100 9200240000
LIR 6M6 V 4 - 6 l M 6 100 9200250000
LIR 6M8 V 4 - 6 l M 8 100 9200260000
LIR 6.0M10 V 4 - 6 l M 10 100 9200270000
Fork-type cable connector Ordering data
Type Cross-section, mm2Colour Dimensions Qty. Order No.
LIS 1.5M3 V 0.5 - 1.5 l M 3 100 9200290000
LIS 1.5M3.5 V 0.5 - 1.5 l M 3.5 100 9200300000
LIS 1.5M4 V 0.5 - 1.5 l M 4 100 9200310000
LIS 1.5M5 V 0.5 - 1.5 l M 5 100 9200320000
LIS 1.5M6 V 0.5 - 1.5 l M 6 100 9200330000
LIS 2.5M3 V 1.5 - 2.5 l M 3 100 9200350000
LIS 2.5M3.5 V 1.5 - 2.5 l M 3.5 100 9200360000
LIS 2.5M4 V 1.5 - 2.5 l M 4 100 9200370000
LIS 2.5M5 V 1.5 - 2.5 l M 5 100 9200380000
LIS 2.5M6 V 1.5 - 2.5 l M 6 100 9200390000
LIS 6.0M4 V 4 - 6 l M 4 100 9200410000
LIS 6.0M5 V 4 - 6 l M 5 100 9200420000
LIS 6.0M6 V 4 - 6 l M 6 100 9200430000
LIS 6.0M8 V 4 - 6 l M 8 100 9200440000
LIS 6.0M10 V 4 - 6 l M 10 100 9200450000
Pin-type cable connector Ordering data
Type Cross-section, mm2Colour Dimensions Qty. Order No.
LIP 1.5R12 V 0.5 - 1.5 l 12.0 100 9200460000
LIP 2.5R12 V 1.5 - 2.5 l 12.0 100 9200470000
LIP 6.0R14 V 4 - 6 l 14.0 100 9200480000
Hook-type cable connector Ordering data
to ESI 50-18 part 2 Type Cross-section. mm2Colour L1 L2 L3 Qty. Order No.
HB 1-17 0.25 - 1.5 l27.2 16.75 4.6 100 9036290000
HB 1-13 1.0 - 2.5 l27.2 16.75 3.0 100 9036300000
L1
L2
B
G.95
Accessories
G
Insulated cable connectors, PVC, with conical cable entry
Butt connector Ordering data
Type Cross-section, mm2Colour Dimensions Qty. Order No.
LIB 1.5B25 VF 0.5 - 1.5 l24.5 100 9200490000
LIB 2.5B25 VF 1.5 - 2.5 l24.5 100 9200500000
LIB 6.0B26 VF 4 - 6 l26.0 100 9200510000
Flat blade receptacles Ordering data
with copper sleeve Type Cross-section, mm2Colour Dimensions Qty. Order No.
LIF 1.5F288 R 0.5 - 1.5 l 2.8 x 0.8 mm 100 9200520000
LIF 1.5F488 R 0.5 - 1.5 l 4.8 x 0.8 mm 100 9200530000
LIF 1.5F638 R 0.5 - 1.5 l 6.3 x 0.8 mm 100 9200540000
LIF 2.5F488 R 1.5 - 2.5 l 4.8 x 0.8 mm 100 9200550000
LIF 2.5F638 R 1.5 - 2.5 l 6.3 x 0.8 mm 100 9200560000
LIF 6.0F638 R 4 - 6 l 6.3 x 0.8 mm 100 9200570000
Flat blade connector Ordering data
with copper sleeve Type Cross-section, mm2Colour Dimensions Qty. Order No.
LIF 1.5M638 R 0.5 - 1.5 l 6.3 x 0.8 mm 100 9200580000
LIF 2.5M638 R 1.5 - 2.5 l 6.3 x 0.8 mm 100 9200590000
LIF 6.0M638 R 4 - 6 l 6.3 x 0.8 mm 100 9200600000
Flat blade receptacles. piggy-back Ordering data
with copper sleeve Type Cross-section, mm2Colour Dimensions Qty. Order No.
LIF 1.5T638 R 0.5 - 1.5 l 6.3 x 0.8 mm 100 9200610000
LIF 2.5T638 R 1.5 - 2.5 l 6.3 x 0.8 mm 100 9200620000
LIF 6.0T638 R 4 - 6 l 6.3 x 0.8 mm 100 9200630000
Flat blade receptacles. full insulation Ordering data
with copper sleeve Type Cross-section, mm2Colour Dimensions Qty. Order No.
LIF 1.5F638 RF 0.5 - 1.5 l 6.3 x 0.8 mm 100 9200640000
LIF 2.5F638 RF 1.5 - 2.5 l 6.3 x 0.8 mm 100 9200650000
LIF 6.0F638 RF 4 - 6 l 6.3 x 0.8 mm 100 9200660000
G.96
Accessories
G
Round plug Ordering data
with copper sleeve Type Cross-section, mm2Colour Dimensions Qty. Order No.
LID 1.5M4 R 0.5 - 1.5 lØ 4 mm 100 9200670000
LID 2.5M5 R 1.5 - 2.5 lØ 5 mm 100 9200680000
LID 6.0M5 R 4 - 6 lØ 5 mm 100 9200690000
Sockets for round plugs Ordering data
with copper sleeve Type Cross-section, mm2Colour Dimensions Qty. Order No.
LID 1.5F4 RF 0.5 - 1.5 l Ø 4 mm 100 9200700000
LID 2.5F5 RF 1.5 - 2.5 l Ø 5 mm 100 9200710000
LID 6.0F5 RF 4 - 6 l Ø 5 mm 100 9200720000
Insulated cable connectors, PVC, with conical cable entry