DATA SH EET
Product specification
File under Integrated Circuits, IC06 December 1990
INTEGRATED CIRCUITS
74HC/HCT4051
8-channel analog
multiplexer/demultiplexer
For a complete data sheet, please also download:
•The IC06 74HC/HCT/HCU/HCMOS Logic Family Specifications
•The IC06 74HC/HCT/HCU/HCMOS Logic Package Information
•The IC06 74HC/HCT/HCU/HCMOS Logic Package Outlines
December 1990 2
Philips Semiconductors Product specification
8-channel analog
multiplexer/demultiplexer 74HC/HCT4051
FEATURES
•Wide analog input voltage range: ±5V.
•Low “ON” resistance:
80 Ω(typ.) at VCC −VEE = 4.5 V
70 Ω(typ.) at VCC −VEE = 6.0 V
60 Ω(typ.) at VCC −VEE = 9.0 V
•Logic level translation:
to enable 5 V logic to communicate with ±5 V analog
signals
•Typical “break before make” built in
•Output capability: non-standard
•ICC category: MSI
GENERAL DESCRIPTION
The 74HC/HCT4051 are high-speed Si-gate CMOS
devices and are pin compatible with the “4051” of the
“4000B” series. They are specified in compliance with
JEDEC standard no. 7A.
The 74HC/HCT4051 are 8-channel analog
multiplexers/demultiplexers with three digital select inputs
(S0 to S2), an active LOW enable input (E), eight
independent inputs/outputs (Y0 to Y7) and a common
input/output (Z).
With E LOW, one of the eight switches is selected (low
impedance ON-state) by S0 to S2. With E HIGH, all
switches are in the high impedance OFF-state,
independent of S0 to S2.
VCC and GND are the supply voltage pins for the digital
control inputs (S0 to S2, and E). The VCC to GND ranges
are 2.0 to 10.0 V for HC and 4.5 to 5.5 V for HCT. The
analog inputs/outputs (Y0 to Y7, and Z) can swing between
VCC as a positive limit and VEE as a negative limit.
VCC −VEE may not exceed 10.0 V.
For operation as a digital multiplexer/demultiplexer, VEE is
connected to GND (typically ground).
QUICK REFERENCE DATA
VEE = GND = 0 V; Tamb =25°C; tr=t
f= 6 ns
Notes
1. CPD is used to determine the dynamic power dissipation (PD in µW):
PD=C
PD ×VCC2×fi+∑{ (CL+C
S)×V
CC2×fo} where:
fi= input frequency in MHz
fo= output frequency in MHz
∑{(C
L+C
S
)×V
CC2×fo} = sum of outputs
CL= output load capacitance in pF
CS = max. switch capacitance in pF
VCC = supply voltage in V
2. For HC the condition is VI= GND to VCC
For HCT the condition is VI= GND to VCC −1.5 V
SYMBOL PARAMETER CONDITIONS TYPICAL UNIT
HC HCT
tPZH/ tPZL turn “ON” time CL= 15 pF; RL=1kΩ;
V
CC =5V
E to Vos 22 22 ns
Sn to Vos 20 24 ns
tPHZ/ tPLZ turn “OFF” time
E to Vos 18 16 ns
Sn to Vos 19 20 ns
CIinput capacitance 3.5 3.5 pF
CPD power dissipation capacitance per switch notes 1 and 2 25 25 pF
CSmax. switch capacitance
independent (Y) 5 5 pF
common (Z) 25 25 pF
December 1990 3
Philips Semiconductors Product specification
8-channel analog multiplexer/demultiplexer 74HC/HCT4051
ORDERING INFORMATION
See
“74HC/HCT/HCU/HCMOS Logic Package Information”
.
PIN DESCRIPTION
PIN NO. SYMBOL NAME AND FUNCTION
3 Z common input/output
6E enable input (active LOW)
7V
EE negative supply voltage
8 GND ground (0 V)
11, 10, 9 S0 to S2select inputs
13, 14, 15, 12, 1, 5, 2, 4 Y0 to Y7independent inputs/outputs
16 VCC positive supply voltage
Fig.1 Pin configuration. Fig.2 Logic symbol. Fig.3 IEC logic symbol.
December 1990 4
Philips Semiconductors Product specification
8-channel analog multiplexer/demultiplexer 74HC/HCT4051
Fig.4 Functional diagram.
APPLICATIONS
•Analog multiplexing and demultiplexing
•Digital multiplexing and demultiplexing
•Signal gating
FUNCTION TABLE
Notes
1. H = HIGH voltage level
L = LOW voltage level
X = don’t care
INPUTS channel
ON
ES
2S
1S
0
L
L
L
L
L
L
L
L
L
L
H
H
L
H
L
H
Y
0
−Z
Y
1
−Z
Y
2
−Z
Y
3
−Z
L
L
L
L
H
H
H
H
L
L
H
H
L
H
L
H
Y
4
−Z
Y
5
−Z
Y
6
−Z
Y
7
−Z
H X X X none
Fig.5 Schematic diagram (one switch).
December 1990 5
Philips Semiconductors Product specification
8-channel analog multiplexer/demultiplexer 74HC/HCT4051
RATINGS
Limiting values in accordance with the Absolute Maximum System (IEC 134)
Voltages are referenced to VEE = GND (ground=0V)
Note to ratings
1. To avoid drawing VCC current out of terminal Z, when switch current flows in terminals Yn, the voltage drop across
the bidirectional switch must not exceed 0.4 V. If the switch current flows into terminal Z, no VCC current will flow out
of terminals Yn. In this case there is no limit for the voltage drop across the switch, but the voltages at Yn and Z may
not exceed VCC or VEE.
RECOMMENDED OPERATING CONDITIONS
SYMBOL PARAMETER MIN. MAX. UNIT CONDITIONS
VCC DC supply voltage −0.5 +11.0 V
±IIK DC digital input diode current 20 mA for VI<−0.5 V or VI> VCC + 0.5 V
±ISK DC switch diode current 20 mA for VS<−0.5 V or VS> VCC + 0.5 V
±ISDC switch current 25 mA for −0.5 V < VS<V
CC + 0.5 V
±IEE DC VEE current 20 mA
±ICC; ±IGND DC VCC or GND current 50 mA
Tstg storage temperature range −65 +150 °C
Ptot power dissipation per package for temperature range: −40 to +125 °C
74HC/HCT
plastic DIL 750 mW above +70 °C: derate linearly with 12 mW/K
plastic mini-pack (SO) 500 mW above +70 °C: derate linearly with 8 mW/K
PSpower dissipation per switch 100 mW
SYMBOL PARAMETER 74HC 74HCT UNIT CONDITIONS
min. typ. max. min. typ. max.
VCC DC supply voltage VCC − GND 2.0 5.0 10.0 4.5 5.0 5.5 V see Figs 6 and 7
VCC DC supply voltage VCC − VEE 2.0 5.0 10.0 2.0 5.0 10.0 V see Figs 6 and 7
VIDC input voltage range GND VCC GND VCC V
VSDC switch voltage range VEE VCC VEE VCC V
Tamb operating ambient temperature
range −40 +85 −40 +85 °Csee DC and AC
CHARACTERISTICS
Tamb operating ambient temperature
range −40 +125 −40 +125 °C
tr, tfinput rise and fall times
6.0
1000
500
400
250
6.0 500 ns
VCC = 2.0 V
VCC = 4.5 V
VCC = 6.0 V
VCC = 10.0 V
December 1990 6
Philips Semiconductors Product specification
8-channel analog multiplexer/demultiplexer 74HC/HCT4051
Fig.6 Guaranteed operating area as a function of
the supply voltages for 74HC4051. Fig.7 Guaranteed operating area as a function of
the supply voltages for 74HCT4051.
DC CHARACTERISTICS FOR 74HC/HCT
For 74HC: VCC −GND or VCC −VEE = 2.0, 4.5, 6.0 and 9.0 V
For 74HCT: VCC −GND = 4.5 and 5.5 V; VCC −VEE = 2.0, 4.5, 6.0 and 9.0 V
Notes to DC characteristics
1. At supply voltages (VCC −VEE) approaching 2.0 V the analog switch ON-resistance becomes extremely non-linear.
Therefore it is recommended that these devices be used to transmit digital signals only, when using these supply
voltages.
2. For test circuit measuring RON see Fig.8.
SYMBOL PARAMETER
Tamb (°C)
UNIT
TEST CONDITIONS
74HC/HCT VCC
(V) VEE
(V) IS
(µA) Vis VI
+25 −40 to +85 −40 to +125
min. typ. max. min. max. min. max.
RON ON resistance (peak) −
100
90
70
−
180
160
130
−
225
200
165
−
270
240
195
Ω
Ω
Ω
Ω
2.0
4.5
6.0
4.5
0
0
0
−4.5
100
1000
1000
1000
VCC
to
VEE
VIH
or
VIL
RON ON resistance (rail) 150
80
70
60
−
140
120
105
−
175
150
130
−
210
180
160
Ω
Ω
Ω
Ω
2.0
4.5
6.0
4.5
0
0
0
−4.5
100
1000
1000
1000
VEE VIH
or
VIL
RON ON resistance (rail) 150
90
80
65
−
160
140
120
−
200
175
150
−
240
210
180
Ω
Ω
Ω
Ω
2.0
4.5
6.0
4.5
0
0
0
−4.5
100
1000
1000
1000
VCC VIH
or
VIL
∆RON maximum ∆ON
resistance between
any two channels
−
9
8
6
Ω
Ω
Ω
Ω
2.0
4.5
6.0
4.5
0
0
0
−4.5
VCC
to
VEE
VIH
or
VIL
December 1990 7
Philips Semiconductors Product specification
8-channel analog multiplexer/demultiplexer 74HC/HCT4051
DC CHARACTERISTICS FOR 74HC
Voltages are referenced to GND (ground = 0 V)
SYMBOL PARAMETER
Tamb (°C)
UNIT
TEST CONDITIONS
74HC VCC
(V) VEE
(V)
ViOTHER
+25 −40 to +85 −40 to +125
min. typ. max. min. max. min. max.
VIH HIGH level input
voltage 1.5
3.15
4.2
6.3
1.2
2.4
3.2
4.7
1.5
3.15
4.2
6.3
1.5
3.15
4.2
6.3
V 2.0
4.5
6.0
9.0
VIL LOW level input
voltage 0.8
2.1
2.8
4.3
0.5
1.35
1.8
2.7
0.5
1.35
1.8
2.7
0.5
1.35
1.8
2.7
V 2.0
4.5
6.0
9.0
±IIinput leakage
current 0.1
0.2 1.0
2.0 1.0
2.0 µA 6.0
10.0 0
0VCC
or
GND
± ISanalog switch
OFF-state current
per channel
0.1 1.0 1.0 µA 10.0 0 VIH
or
VIL
|VS|=
V
CC −VEE
Fig.10
± ISanalog switch
OFF-state current
all channels
0.4 4.0 4.0 µA 10.0 0 VIH
or
VIL
|VS|=
V
CC − VEE
Fig.10
±ISanalog switch
ON-state current 0.4 4.0 4.0 µA 10.0 0 VIH
or
VIL
|VS|=
V
CC −VEE
Fig.11
ICC quiescent supply
current 8.0
16.0 80.0
160.0 160.0
320.0 µA 6.0
10.0 0
0VCC
or
GND
Vis =VEE
or VCC;
Vos = VCC
or VEE
December 1990 8
Philips Semiconductors Product specification
8-channel analog multiplexer/demultiplexer 74HC/HCT4051
AC CHARACTERISTICS FOR 74HC
GND = 0 V; tr=t
f= 6 ns; CL=50pF
SYMBOL PARAMETER
Tamb (°C)
UNIT
TEST CONDITIONS
74HC VCC
(V) VEE
(V) OTHER
+25 −40 to +85 −40 to +125
min. typ. max. min. max. min. max.
tPHL/ tPLH propagation delay
Vis to Vos
14
5
4
4
60
12
10
8
75
15
13
10
90
18
15
12
ns 2.0
4.5
6.0
4.5
0
0
0
−4.5
RL=∞; CL=50pF
(see Fig.17)
tPZH/ tPZL turn “ON” time
E to Vos
72
29
21
18
345
69
59
51
430
86
73
64
520
104
88
77
ns 2.0
4.5
6.0
4.5
0
0
0
−4.5
RL=1kΩ;
C
L=50pF
(see Fig.18, 19 and
20)
tPZH/ tPZL turn “ON” time
Sn to Vos
66
28
19
16
345
69
59
51
430
86
73
64
520
104
88
77
ns 2.0
4.5
6.0
4.5
0
0
0
−4.5
RL=1kΩ;
C
L=50pF
(see Fig.18, 19 and
20)
tPHZ/ tPLZ turn “OFF” time
E to Vos
58
31
17
18
290
58
49
42
365
73
62
53
435
87
74
72
ns 2.0
4.5
6.0
4.5
0
0
0
−4.5
RL=1kΩ;
C
L=50pF
(see Fig.18, 19 and
20)
tPHZ/ tPLZ turn “OFF” time
Sn to Vos
61
25
18
18
290
58
49
42
365
73
62
53
435
87
74
72
ns 2.0
4.5
6.0
4.5
0
0
0
−4.5
RL=1kΩ;
C
L=50pF
(see Fig.18, 19 and
20)
December 1990 9
Philips Semiconductors Product specification
8-channel analog multiplexer/demultiplexer 74HC/HCT4051
DC CHARACTERISTICS FOR 74HCT
Voltages are referenced to GND (ground = 0)
Note to HCT types
1. The value of additional quiescent supply current (∆ ICC) for a unit load of 1 is given here.
To determine ∆ICC per input, multiply this value by the unit load coefficient shown in the table below.
SYMBOL PARAMETER
Tamb (°C)
UNIT
TEST CONDITIONS
74HCT VCC
(V) VEE
(V) ViOTHER+25 −40 to +85 −40 to +125
min. typ. max. min. max. min. max.
VIH HIGH level
input voltage 2.0 1.6 2.0 2.0 V 4.5
to
5.5
VIL LOW level
input voltage 1.2 0.8 0.8 0.8 V 4.5
to
5.5
±IIinput leakage
current 0.1 1.0 1.0 µA 5.5 0 VCC
or
GND
± ISanalog switch
OFF-state
current per
channel
0.1 1.0 1.0 µA 10.0 0 VIH
or
VIL
|VS|=
V
CC − VEE
(see Fig.10)
± ISanalog switch
OFF-state
current all
channels
0.4 4.0 4.0 µA 10.0 0 VIH
or
VIL
|VS|=
V
CC −VEE
(see Fig.10)
±ISanalog switch
ON-state
current
0.4 4.0 4.0 µA 10.0 0 VIH
or
VIL
|VS| =
VCC−VEE
(see Fig.11)
ICC quiescent
supply current 8.0
16.0 80.0
160.0 160.0
320.0 µA 5.5
5.0 0
−5.0 VCC
or
GND
Vis =VEE or
VCC;
Vos = VCC
or VEE
∆ICC additional
quiescent
supply current
per input pin
for unit load
coefficient is 1
(note 1)
100 360 450 490 µA 4.5
to
5.5
0V
CC
−2.1
V
other inputs
at VCC or
GND
INPUT UNIT LOAD COEFFICIENT
Sn
E0.50
0.50
December 1990 10
Philips Semiconductors Product specification
8-channel analog multiplexer/demultiplexer 74HC/HCT4051
AC CHARACTERISTICS FOR 74HCT
GND = 0 V; tr=t
f= 6 ns; CL=50pF
SYMBOL PARAMETER
Tamb (°C)
UNIT
TEST CONDITIONS
74HCT VCC
(V) VEE
(V) OTHER
+25 −40 to +85 −40 to +125
min. typ. max. min. max. min. max.
tPHL/ tPLH propagation
delay Vis to Vos
5
412
815
10 18
12 ns 4.5
4.5 0
−4.5 RL=∞; CL=50pF
(see Fig.17)
tPZH/ tPZL turn “ON” time
E to Vos
26
16 55
39 69
49 83
59 ns 4.5
4.5 0
−4.5 RL=1kΩ; CL=50pF
(see Fig.18, 19 and 20)
tPZH/ tPZL turn “ON” time
Sn to Vos
28
16 55
39 69
49 83
59 ns 4.5
4.5 0
−4.5 RL=1kΩ; CL=50pF
(see Fig.18, 19 and 20)
tPHZ/ tPLZ turn “OFF”
time E to Vos
19
16 45
32 56
40 68
48 ns 4.5
4.5 0
−4.5 RL=1kΩ; CL=50pF
(see Fig.18, 19 and 20)
tPHZ/ tPLZ turn “OFF”
time Sn to Vos
23
16 45
32 56
40 68
48 ns 4.5
4.5 0
−4.5 RL=1kΩ; CL=50pF
(see Fig.18, 19 and 20)
Fig.8 Test circuit for measuring RON.Fig.9 Typical RON as a function of input voltage Vis
for Vis = 0 to VCC − VEE.
December 1990 11
Philips Semiconductors Product specification
8-channel analog multiplexer/demultiplexer 74HC/HCT4051
Fig.10 Test circuit for measuring OFF-state current.
Fig.11 Test circuit for measuring ON-state current.
December 1990 12
Philips Semiconductors Product specification
8-channel analog multiplexer/demultiplexer 74HC/HCT4051
ADDITIONAL AC CHARACTERISTICS FOR 74HC/HCT
Recommended conditions and typical values
GND = 0 V; Tamb =25°C
Notes to AC characteristics
1. Adjust input voltage Vis to 0 dBm level (0 dBm = 1 mW into 600 Ω).
2. Adjust input voltage Vis to 0 dBm level at Vos for 1 MHz (0 dBm = 1 mW into 50 Ω).
General note
Vis is the input voltage at a Yn or Z terminal, whichever is assigned as an input.
Vos is the output voltage at a Yn or Z terminal, whichever is assigned as an output.
SYMBOL PARAMETER typ. UNIT VCC
(V) VEE
(V) Vis(p−p)
(V) CONDITIONS
sine-wave distortion
f = 1 kHz 0.04
0.02 %
%2.25
4.5 −2.25
−4.5 4.0
8.0 RL=10kΩ; CL=50pF
(see Fig.14)
sine-wave distortion
f = 10 kHz 0.12
0.06 %
%2.25
4.5 −2.25
−4.5 4.0
8.0 RL=10kΩ; CL=50pF
(see Fig.14)
switch “OFF” signal
feed-through −50
−50 dB
dB 2.25
4.5 −2.25
−4.5 note 1 RL= 600 Ω; CL=50pF
(see Figs 12 and 15)
V(p−p)
crosstalk voltage between
control and any switch
(peak-to-peak value)
110
220 mV
mV 4.5
4.5 0
−4.5
RL= 600 Ω; CL= 50 pF;
f = 1 MHz (E or Sn,
square-wave between
VCC and GND,
tr=t
f= 6 ns)
(see Fig.16)
fmax minimum frequency
response (−3dB) 170
180 MHz
MHz 2.25
4.5 −2.25
−4.5 note 2 RL=50Ω;C
L= 10 pF
(see Fig.13 and 14)
CSmaximum switch capacitance
independent (Y)
common (Z) 5
25 pF
pF
Fig.12 Typical switch “OFF” signal feed-through as a function of frequency.
Test conditions:
VCC = 4.5 V; GND = 0 V; VEE =−4.5 V;
RL=50Ω; Rsource =1kΩ
December 1990 13
Philips Semiconductors Product specification
8-channel analog multiplexer/demultiplexer 74HC/HCT4051
Test conditions:
VCC = 4.5 V; GND = 0 V; VEE =−4.5 V;
RL=50Ω; Rsource =1kΩ
Fig.13 Typical frequency response.
Fig.14 Test circuit for measuring sine-wave
distortion and minimum frequency response. Fig.15 Test circuit for measuring switch “OFF”
signal feed-through.
Fig.16 Test circuit for measuring crosstalk between control and any switch.
The crosstalk is defined as follows (oscilloscope output):
December 1990 14
Philips Semiconductors Product specification
8-channel analog multiplexer/demultiplexer 74HC/HCT4051
AC WAVEFORMS
Fig.17 Waveforms showing the input (Vis) to output (Vos) propagation delays.
(1) HC : VM= 50%; VI= GND to VCC.
HCT: VM= 1.3 V; VI= GND to 3 V.
Fig.18 Waveforms showing the turn-ON and turn-OFF times.
December 1990 15
Philips Semiconductors Product specification
8-channel analog multiplexer/demultiplexer 74HC/HCT4051
TEST CIRCUIT AND WAVEFORMS
Fig.19 Test circuit for measuring AC performance.
Conditions
TEST SWITCH Vis
tPZH
tPZL
tPHZ
tPLZ
others
VEE
VCC
VEE
VCC
open
VCC
VEE
VCC
VEE
pulse
FAMILY AMPLITUDE VM
tr; tf
fmax;
PULSE WIDTH OTHER
74HC
74HCT VCC
3.0 V 50%
1.3 V <2ns
<2ns 6ns
6ns
C
L= load capacitance including jig and probe capacitance (see AC CHARACTERISTICS for values).
RT= termination resistance should be equal to the output impedance ZO of the pulse generator.
tr=t
f= 6 ns; when measuring fmax, there is no constraint to tr, tf with 50% duty factor.
Fig.20 Input pulse definitions.
Conditions
TEST SWITCH Vis
tPZH
tPZL
tPHZ
tPLZ
others
VEE
VCC
VEE
VCC
open
VCC
VEE
VCC
VEE
pulse
FAMILY AMPLITUDE VM
tr; tf
fmax;
PULSE WIDTH OTHER
74HC
74HCT VCC
3.0 V 50%
1.3 V <2ns
<2ns 6ns
6ns
C
L= load capacitance including jig and probe capacitance (see AC CHARACTERISTICS for values).
RT= termination resistance should be equal to the output impedance ZO of the pulse generator.
tr=t
f= 6 ns; when measuring fmax, there is no constraint to tr, tf with 50% duty factor.
December 1990 16
Philips Semiconductors Product specification
8-channel analog multiplexer/demultiplexer 74HC/HCT4051
PACKAGE OUTLINES
See
“74HC/HCT/HCU/HCMOS Logic Package Outlines”
.
Philips Semiconductors - PIP - 74HC/HCT4051; 8-channel analog multiplexer/demultiplexer
Philips Semiconductors Home
Product
catalog
Buy
online
MySemiconductors
Contact
Products
•MultiMarket
Semiconductors
•Product Selector
•Catalog by
Function
•Catalog by
System
•Cross-reference
•Packages
•End of Life
information
•Distributors Go
Here!
•Models
•SoC solutions
Product Information
74HC/HCT4051; 8-
channel analog
multiplexer/demultiplexer
Information as of 2003-04-22
My.Semiconductors.COM.
Your personal service from
Philips Semiconductors.
Please register now !
Stay informed
Use right mouse button to
download datasheet
Download datasheet
General description Features Applications Datasheet
Block diagram Buy online Support & tools Email/translate
Products & packages Parametrics Similar products
top
General description
The 74HC/HCT4051 are high-speed Si-gate CMOS devices and are pin compatible with the '4051' of the '4000B' series. They
are specified in compliance with JEDEC standard no. 7A.
The 74HC/HCT4051 are 8-channel analog multiplexers/demultiplexers with three digital select inputs (S0 to S2), an active LOW enable input (E), eight
independent inputs/outputs (Y0 to Y7) and a common input/output (Z).
With E LOW, one of the eight switches is selected (low impedance ON-state) by S0 to S2. With E HIGH, all switches are in the high impedance OFF-state, independent of S0 to S2.
VCC and GND are the supply voltage pins for the digital control inputs (S0 to S2, and E). The VCC to GND ranges are 2.0 to 10.0 V for HC and 4.5 to 5.5 V for HCT. The analog inputs/outputs (Y0 to Y7, and Z) can swing between VCC as a positive limit and VEE as a negative limit.
VCC - VEE may not exceed 10.0 V.
For operation as a digital multiplexer/demultiplexer, VEE is connected to GND (typically ground).
file:///G|/imaging/BITTING/CPL/20030424/04232003_9/PHGL/_HTML04232003/74HC4051N.html (1 of 5) [Apr-29-2003 2:21:25 PM]
Philips Semiconductors - PIP - 74HC/HCT4051; 8-channel analog multiplexer/demultiplexer
top
Features
● Wide analog input voltage range: ± 5 V.
● Low 'ON' resistance:
80 Ω (typ.) at VCC - VEE = 4.5 V
70 Ω (typ.) at VCC - VEE = 6.0 V
60 Ω (typ.) at VCC - VEE = 9.0 V
● Logic level translation: to enable 5 V logic to communicate with ± 5 V analog signals
● Typical 'break before make' built in
● Output capability: non-standard
● ICC category: MSI
top
Datasheet
Type number Title Publication
release date Datasheet status Page
count File
size
(kB)
Datasheet
74HC/HCT4051 8-channel analog
multiplexer/demultiplexer 12/1/1990 Product
specification 16 118
Download
PDF
File
Download
Additional datasheet info
To complete the device datasheet with package and family information, also download the following PDF files. The "Logic
Package Information" document is required to determine in which package(s) this device is available.
Document Description
1
Download
PDF
File
HCT_FAMILY_SPECIFICATIONS HC/T Family Specifications, The IC06 74HC/HCT/HCMOS Logic Family
Specifications
2
Download
PDF
File
HCT_PACKAGE_INFO HC/T Package Info, The IC06 74HC/HCT/HCMOS Logic Package Information
3
Download
PDF
File
HCT_PACKAGE_OUTLINES HC/T Package Outlines, The IC06 74HC/HCT/HCMOS Logic Package
Outlines
file:///G|/imaging/BITTING/CPL/20030424/04232003_9/PHGL/_HTML04232003/74HC4051N.html (2 of 5) [Apr-29-2003 2:21:25 PM]
Philips Semiconductors - PIP - 74HC/HCT4051; 8-channel analog multiplexer/demultiplexer
top
Parametrics
Type number Package Description Propagation
Delay(ns) Voltage No.
of
Pins
Power
Dissipation
Considerations
Logic
Switching
Levels
Output
Drive
Capability
74HC4051D SOT109
(SO16) 8-Channel Analog
Multiplexer/Demultiplexer 10~15 5 Volts
+16 Low Power or
Battery
Applications CMOS Low
74HC4051DB SOT338-1
(SSOP16) 8-Channel Analog
Multiplexer/Demultiplexer 10~15 5 Volts
+16 Low Power or
Battery
Applications CMOS Low
74HC4051N SOT38-1
(DIP16) 8-Channel Analog
Multiplexer/Demultiplexer 10~15 5 Volts
+16 Low Power or
Battery
Applications CMOS Low
74HC4051PW SOT403-1
(TSSOP16) 8-Channel Analog
Multiplexer/Demultiplexer 10~15 5 Volts
+16 Low Power or
Battery
Applications CMOS Low
74HCT4051D SOT109
(SO16)
8-Channel Analog
Multiplexer/Demultiplexer;
TTL Enabled 10~15 5 Volts
+16 Low Power or
Battery
Applications TTL Low
74HCT4051DB SOT338-1
(SSOP16)
8-Channel Analog
Multiplexer/Demultiplexer;
TTL Enabled 10~15 5 Volts
+16 Low Power or
Battery
Applications TTL Low
74HCT4051N SOT38-1
(DIP16)
8-Channel Analog
Multiplexer/Demultiplexer;
TTL Enabled 10~15 5 Volts
+16 Low Power or
Battery
Applications TTL Low
file:///G|/imaging/BITTING/CPL/20030424/04232003_9/PHGL/_HTML04232003/74HC4051N.html (3 of 5) [Apr-29-2003 2:21:25 PM]
Philips Semiconductors - PIP - 74HC/HCT4051; 8-channel analog multiplexer/demultiplexer
top
Products, packages, availability and ordering
Type number North American
type number Ordering code
(12NC) Marking/Packing
Download
PDF
File
Discretes packing
info
Package Device status Buy online
74HC4051D 74HC4051D 9337 148 20652 Standard Marking *
Bulk Pack, CECC SOT109
(SO16) Full production
order this
product
online
-
74HC4051D-T 9337 148 20653 Standard Marking *
Reel Pack, SMD,
13", CECC
SOT109
(SO16) Full production
order this
product
online
-
74HC4051DB 74HC4051DB 9351 738 10112 Standard Marking *
Bulk Pack SOT338-1
(SSOP16) Full production
order this
product
online
-
74HC4051DB-T 9351 738 10118 Standard Marking *
Reel Pack, SMD,
13"
SOT338-1
(SSOP16) Full production
order this
product
online
-
74HC4051N 74HC4051N 9336 697 40652 Standard Marking *
Bulk Pack, CECC SOT38-1
(DIP16) Full production
order this
product
online
-
74HC4051PW 74HC4051PW 9351 874 80112 Standard Marking *
Bulk Pack SOT403-1
(TSSOP16) Full production
order this
product
online
-
74HC4051PW-T 9351 874 80118 Standard Marking *
Reel Pack, SMD,
13"
SOT403-1
(TSSOP16) Full production
order this
product
online
-
74HCT4051D 74HCT4051D 9337 153 00112 Standard Marking *
Bulk Pack SOT109
(SO16) Full production
order this
product
online
-
74HCT4051D-T 9337 153 00118 Standard Marking *
Reel Pack, SMD,
13"
SOT109
(SO16) Full production
order this
product
online
-
74HCT4051DB 74HCT4051DB 9351 738 00112 Standard Marking *
Bulk Pack SOT338-1
(SSOP16) Full production
order this
product
online
-
74HCT4051DB-
T 9351 738 00118 Standard Marking *
Reel Pack, SMD,
13"
SOT338-1
(SSOP16) Full production
order this
product
online
-
74HCT4051N 74HCT4051N 9336 703 70112 Standard Marking *
Bulk Pack SOT38-1
(DIP16) Full production
order this
product
-
file:///G|/imaging/BITTING/CPL/20030424/04232003_9/PHGL/_HTML04232003/74HC4051N.html (4 of 5) [Apr-29-2003 2:21:25 PM]
Philips Semiconductors - PIP - 74HC/HCT4051; 8-channel analog multiplexer/demultiplexer
online
74HCT4051PW 9352 704 18112 Standard Marking *
Bulk Pack SOT403 Full production -
9352 704 18118 Standard Marking *
Reel Pack, SMD,
13" SOT403 Full production -
top
Similar products
Products
similar
to
74HC/HCT4051
74HC/HCT4051 links to the similar products page containing an overview of products that are similar in function or
related to the type number(s) as listed on this page. The similar products page includes products from the same catalog tree(s),
relevant selection guides and products from the same functional category.
top
Support & tools
Download
PDF
File
HC/T Family Specifications, The IC06 74HC/HCT/HCMOS Logic Family Specifications(date 01-Mar-98)
Download
PDF
File
HC/T User Guide(date 01-Nov-97)
top
Email/translate this product information
● Email this product information.
● Translate this product information page from English to:
The English language is the official language used at the semiconductors.philips.com website and webpages. All translations
on this website are created through the use of Google Language Tools and are provided for convenience purposes only. No
rights can be derived from any translation on this website.
About this Web Site
| Copyright © 2003 Koninklijke Philips N.V. All rights reserved. | Privacy Policy |
| Koninklijke Philips N.V. | Access to and use of this Web Site is subject to the following Terms of Use. |
file:///G|/imaging/BITTING/CPL/20030424/04232003_9/PHGL/_HTML04232003/74HC4051N.html (5 of 5) [Apr-29-2003 2:21:25 PM]
French
Translate