HPR12K-00 - ARTESYN EMBEDDED POWER

Rev.06.09.10

HPR12K-00

1 of 6

313

process

yellow

3405

1797

1375

116

2607

652

242

2985

375

240

Embedded Power for

Business-Critical Continuity

Operating Instructions

1. General Install

Connecting the input power cable, output load cable and communication wire according

to the below figure.

HPR12K-00

AC INPUT AC INPUT AC INPUT AC INPUTMain DC Output

Aux. DC

Output

I2C/PMBus

Communication

Main DC Output

AC Line Input

2. General Settings

Unless otherwise specified, when the PSON# switch is de-asserted (48V o/p is disabled).

It is means Manual ON/OFF DIP switch SW1 should be default according to below table.

And It must be checked before shipping.

Power Supplies

Status

PSU 1# PSU 2# PSU 3# PSU 4#

CH 1 CH 2 CH 3 CH 4 CH 5 CH 6 CH 7 CH8

OFF Up Down Up Down Up Down Up Down

Note 1. The status Down means set to ON position. The status UP means set to OFF position.

Note 2. Programming Switch SW1 default settings:

PSON switches : OFF

PSKILL switches : ON

DIP switch SW1 setting as a default

Rev.06.09.10

HPR12K-00

2 of 6

313

process

yellow

3405

1797

1375

116

2607

652

242

2985

375

240

Embedded Power for

Business-Critical Continuity

Technical Reference Note

3.1 Manual ON/OFF Operation

3. ON/OFF Operation (PSON#)

The DIP switch SW1 used turn on or off the PSU by manually. The PSU in SLOT1 is turn on when the CH1 of DIP switch

SW1 turn on. The other PSU see Table 1.

Note : DIP switch CH2 should be set to ON as a default. Incase if CH2 is set to off, Power supply is slot 1 will not turn on

even if CH1 is set to ON position.

Power Supplies

Status

PSU 1# PSU 2# PSU 3# PSU 4#

CH 1 CH 2 CH 3 CH 4 CH 5 CH 6 CH 7 CH8

ON Down Down Down Down Down Down Down Down

OFF Up Down Up Down Up Down Up Down

Note. The status Down means set to ON position. The status UP means set to OFF position.

Table 1 PSON# Switch Characteristics

Figure 1: DIP Switch for ON/OFF Operation

Figure 2: The SLOTs define of Rack

Rev.06.09.10

HPR12K-00

3 of 6

Embedded Power for

Business-Critical Continuity

313

process

yellow

3405

1797

1375

116

2607

652

242

2985

375

240

3.2 Remote ON/OFF

The per PSON# signal is required to remotely turn on/off the power supply. PSON# is an active low signal that turns on

the +48VDC power rail. When this signal is not pulled low by the system, or left open, the +48VDC output turns off.

The 5Vsb output remains on. This signal is pulled to a standby voltage by a pull-up resistor internal to the power sup-

ply. The power supply fan(s) shall operate at the lowest speed.

Signal Type Accepts an open collector/drain input from the system.

Pulled-up to the 3V3sb located inside the power supply.

PSON# = Low ON

PSON# = Open OFF

MIN MAX

Logic level low (power supply ON) 0 V 0.4 V

Logic level high (power supply OFF) 2.40 V 3.40 V

Source current, Vpson = low 4 mA

Power up delay: T pson_on_delay 5msec 400msec

Refer to IPS of HPS3000-9 PN: 41966008950

Table 2 PSON# Signal Characteristics

4. PMBus Communication

The per power supplies can be communicated with computer by our GUI interface hardware and software.

Rev.06.09.10

HPR12K-00

4 of 6

Embedded Power for

Business-Critical Continuity

313

process

yellow

3405

1797

1375

116

2607

652

242

2985

375

240

5.1 Main Output Connection

5. Connector Define for I/O

No. Designation Identification Terminal Type

+48Vdc + MAIN OUTPUT Ring Lug, M6 screw

+48V_RTN - MAIN OUTPUT RETURN Ring Lug, M6 screw

Mating Terminal screw: SUPPLY TECHNOLOGIES 6040289-0010-EC-A

Table 3 Main Output Connection Definition

5.2 PMBus Communication Connection

Use output connector below table5 , Description named CN1.

Self Connector Mating Connector

Landwin 2051P1000T Housing: Landwin 2050S1000

(Astec P/N: 13866002800) Pins: Landwin 2053T011P

Table 4 PMBus Output Connector

Figure 3: Connector CN1

Signal Name Description Pin Qty. Pin Number (s)

SCL Serial Clock Signal 1 4

SDA Serial Data Signal 1 2

Ishare Load Share Bus 1 7

5Vsb 5Vsb External Bus 1 1

Sys_GND Secondary Return 1 3

Unused 5 5, 6, 8, 9, 10

Table 5 Output Connection Definitions for PMBus

5.3 5V Stand-By Auxiliary Output CN2

Self Connector Mating Connector

Tyco: 1-794528-1 Tyco: 794657-6

(Astec P/N: 13870012770)

Table 6 PMBus Output Connector

Figure 4: Connector CN2

Signal Name Description Pin Qty. Pin Number (s)

Stby_Rtn_Sense Return sense for Stby ground 1 1

5Vsb 5Vsb External Bus 22, 3

Sys_GND Standby GND 25, 6

Unused 1 4

Table 7 Output Connection Definitions foe 5V Standby

Rev.06.09.10

HPR12K-00

5 of 6

Embedded Power for

Business-Critical Continuity

313

process

yellow

3405

1797

1375

116

2607

652

242

2985

375

240

5.4 Signal Output Connector CN3

Self Connector Mating Connector

Molex: 52986-2679 Tyco: 2-5175677-4

(Astec P/N: 13870011610)

Table 8 Signal Output Connector

Figure 5: Connector CN3

Signal Name Description Pin Qty. Pin Number (s)

SYS_GND Standby GND 21, 14

UNIT1_PRESENT# Power supply present for Unit 1 1 2

UNIT2_PRESENT# Power supply present for Unit 2 1 3

UNIT3_PRESENT# Power supply present for Unit 3 1 4

UNIT4_PRESENT# Power supply present for Unit 4 1 5

UNIT1_DCOK/PWOK# Power OK output for Unit 1 1 6

UNIT2_DCOK/PWOK# Power OK output for Unit 2 1 7

UNIT3_DCOK/PWOK# Power OK output for Unit 3 1 8

UNIT4_DCOK/PWOK# Power OK output for Unit 4 1 9

UNIT1_ACOK# AC input present for Unit 1 1 10

UNIT2_ACOK# AC input present for Unit 2 1 11

UNIT3_ACOK# AC input present for Unit 3 1 12

UNIT4_ACOK# AC input present for Unit 4 1 13

UNIT1_PSON# Power enable input for Unit 1 1 15

UNIT2_PSON# Power enable input for Unit 2 1 16

UNIT3_PSON# Power enable input for Unit 3 1 17

UNIT4_PSON# Power enable input for Unit 4 1 18

UNIT1_PSKILL Minimize arching damage to the power pins 1 19

UNIT2_PSKILL Minimize arching damage to the power pins 1 20

UNIT3_PSKILL Minimize arching damage to the power pins 1 21

UNIT4_PSKILL Minimize arching damage to the power pins 1 22

UNIT1_#ALERT Warning signal 1 23

UNIT2_#ALERT Warning signal 1 24

UNIT3_#ALERT Warning signal 1 25

UNIT4_#ALERT Warning signal 1 26

Table 7 Output Connection Definitions foe 5V Standby

Rev.06.09.10

HPR12K-00

6 of 6

Americas

5810 Van Allen Way

Carlsbad, CA 92008

USA

Telephone: +1 760 930 4600

Facsimile: +1 760 930 0698

Europe (UK)

Waterfront Business Park

Merry Hill, Dudley

West Midlands, DY5 1LX

United Kingdom

Telephone: +44 (0) 1384 842 211

Facsimile: +44 (0) 1384 843 355

Asia (HK)

14/F, Lu Plaza

2 Wing Yip Street

Kwun Tong, Kowloon

Hong Kong

Telephone: +852 2176 3333

Facsimile: +852 2176 3888

For global contact, visit:

www.Emerson.com/EmbeddedPower

techsupport.embeddedpower

@emerson.com

While every precaution has been taken to ensure

accuracy and completeness in this literature, Emerson

Network Power assumes no responsibility, and disclaims

all liability for damages resulting from use of this

information or for any errors or omissions.

Emerson Network Power and the Emerson

Network Power logo are trademarks and

service marks of Emerson Electric Co.

EmersonNetworkPower.com

Embedded Computing

Embedded Power

Monitoring

Outside Plant

Power Switching & Controls

Precision Cooling

Racks & Integrated Cabinets

Services

Surge Protection

Emerson Network Power.

The global leader in enabling

business-critical continuity.

AC Power

Connectivity

DC Power

313

process

yellow

3405

1797

1375

116

2607

652

242

2985

375

240

Embedded Power for

Business-Critical Continuity

5.5 Input Connection Definition

For Functional Test (NHR – initial testing), the following connection applies.

No. Designation Identification Terminal Type

L VINP Input Voltage Positive Ring Lug, #12 screw

N VINN Input Voltage Negative Ring Lug, #12 screw

E MGND Module Ground (chassis) Mounting Hardware

Table 10 Input Connection Definition

Figure 6: Input Connector

Self Connector Mating Connector

Bussman: A207403R46 Molex: 19073-0222 or Equivalent

(Astec P/N: 15000300070)

Table 11 Input Connection and Mating Terminal