IP140MA SERIES IP140M SERIES IP78M00A SERIES IP78M00 SERIES 0.5 AMP POSITIVE VOLTAGE REGULATOR ! 2 1 3 FEATURES Pin 1 - VIN Pin 2 - VOUT Case - Ground Pin 1 - VIN Pin 2 - Ground Pin 3 - VOUT H Package - TO-39 * OUTPUT CURRENT UP TO 0.5A * OUTPUT VOLTAGES OF 5, 12, 15V SMD 1 CERAMIC SURFACE MOUNT * 0.01% / V LINE REGULATION * 0.3% / A LOAD REGULATION GND 1 8 NC * THERMAL OVERLOAD PROTECTION NC 2 7 NC * SHORT CIRCUIT PROTECTION NC 3 6 VOUT * OUTPUT TRANSISTOR SOA PROTECTION V IN 4 5 NC * 1% VOLTAGE TOLERANCE (-A VERSIONS) 8 Pin J Package Order Information Part H-Pack Number (TO-39) IP78MxxAzz IP78Mxxzz IP140MAzz-xx IP140Mzz-xx Note: xx = Voltage Code (05, 12, 15) eg. IP78M05J J-Pack CERDIP SG-Pack SMD DESCRIPTION Temp. Range -55 to +150C " " " zz = Package Code (H, J, SG) IP140MAH-12 The IP140MA and IP78M00A series of voltage regulators are fixed output regulators intended for local, on-card voltage regulation. These devices are available in 5, 12, and 15 volt options and are capable of delivering in excess of 500mA over temperature. The A-suffix devices are fully specified at 0.5A, provide 0.01% / V line regulation, 0.3% / A load regulation, and 1% output voltage tolerance at room temperature. Protection features include safe operating area, current limiting and thermal shutdown. ABSOLUTE MAXIMUM RATINGS (TC = 25C unless otherwise stated) (for VO = 5, 12, 15V) 35V VI DC Input Voltage PD Power Dissipation RqJC RqJC Thermal Resistance Junction to Case - H Package Thermal Resistance Junction to Case - SG Package TBA C / W RqJA TJ Thermal Resistance Junction to Ambient - J Package 119C / W Operating Junction Temperature Range -55 to 150C Tstg Storage Temperature -65 to 150C Internally limited 1 20C / W Note 1. Although power dissipation is internally limited, these specifications are applicable for maximum power dissipation PMAX of 2W for the H-Package ,1.05W for the J-Package and 15W for the SG-Package. Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: sales@semelab.co.uk Website: http://www.semelab.co.uk Prelim.7/00 IP140MA SERIES IP140M SERIES IP78M00A SERIES IP78M00 SERIES ELECTRICAL CHARACTERISTICS Parameter Test Conditions IO = 100mA VO IP78M05A IP140MA-05 Min. Typ. Max. Output Voltage VIN = 10V 4.95 5 PD PMAX 4.85 IO = 200mA Load Regulation IQ Quiescent Current VIN = 10V TJ = -55 to 150C VIN = 10V IO = 350mA 10 25 3 10 50 5 50 50 mV 4 6 6 mA 0.1 0.5 TJ = -55 to 150C VIN = 10V TJ = -55 to 150C Change IO = 200mA VIN = 8V to 25V Voltage DVIN DVO Ripple Rejection Dropout Voltage VIN = 8V to 18V Short Circuit Current VIN = 35V Ipk Peak Output Current VIN = 10V Coefficient of VO IO = 100mA TJ = -55 to 150C 0.2 0.8 40 200 IO = 5mA 0.5 0.8 40 65 80 62 65 80 62 2 2.5 300 600 1.0 1.4 0.5 2.0 IO = 350mA Isc Average Temperature IO = 300mA 4 mV mA f = 10Hz to 100kHz f = 120Hz V 3 IO = 5mA to 500mA Quiescent Current Output Noise 5.25 50 VIN = 8V to 12V TJ = -55 to 150C VN 4.75 5.2 10 VIN = 8V to 25V IO = 5mA to 500mA DIQ 5.15 5 3 TJ = -55 to 150C IO = 500mA DVO 4.8 Units TJ = -55 to 150C VIN = 7V to 25V Line Regulation 5.05 IO = 5mA to 350mA VIN = 7.5V to 20V DVO IP78M05 IP140M-05 Min. Typ. Max. 0.7 0.7 200 mV dB 2.5 V 300 600 mA 1.0 1.6 A 0.5 mV C 1) All characteristics are measured with a capacitor across the input of 0.22mF and a capacitor across the output of 0.1mF. All characteristics except noise voltage and ripple rejection ratio are measured using pulse techniques (tp voltage changes due to changes in internal temperature must be taken into account separately. 10ms, d 5%). Output 2) Test Conditions unless otherwise stated: TJ = 25C PMAX = 2W for H Package (TO-39) PMAX = 1.05W for J Package (CERDIP) PMAX = 15W for SG Package (SMD1) Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: sales@semelab.co.uk Website: http://www.semelab.co.uk Prelim.7/00 IP140MA SERIES IP140M SERIES IP78M00A SERIES IP78M00 SERIES ELECTRICAL CHARACTERISTICS Parameter IP78M12 IP140M-12 Min. Typ. Max. VIN = 19V 11.88 12.12 11.50 VIN = 14.8V to 27V 11.64 12.36 11.40 Test Conditions IO = 100mA VO IP78M12A IP140MA-12 Min. Typ. Max. Output Voltage 12 12 12.50 IO = 5mA to 350mA PD PMAX Units 12.60 V TJ = -55 to 150C IO = 200mA DVO IQ Quiescent Current IO = 5mA to 500mA VIN = 19V TJ = -55 to 150C VIN = 19V IO = 350mA Quiescent Current VIN = 19V TJ = -55 to 150C Change IO = 200mA VIN = 14.8V to 30V Output Noise Voltage DVIN DVO Ripple Rejection Dropout Voltage f = 120Hz VIN = 15V to 25V 4 18 120 10 60 120 mV 4 6 6 mA 0.1 0.5 IO = 300mA IO = 100mA TJ = -55 to 150C 0.2 0.8 75 480 Ipk Peak Output Current VIN = 19V IO = 5mA 4 mV 0.5 0.8 75 58 72 55 58 72 55 2 2.5 300 600 1.0 1.4 1.2 4.8 IO = 350mA Short Circuit Current VIN = 35V Coefficient of VO 30 mA f = 10Hz to 100kHz Isc Average Temperature 18 TJ = -55 to 150C TJ = -55 to 150C VN 4 VIN = 16V to 22V IO = 5mA to 500mA DIQ 60 TJ = -55 to 150C IO = 500mA Load Regulation 18 VIN = 16V to 30V Line Regulation DVO 4 VIN = 14.5V to 30V 0.7 0.7 480 mV dB 2.5 V 300 600 mA 1.0 1.6 A 1.2 mV C 1) All characteristics are measured with a capacitor across the input of 0.22mF and a capacitor across the output of 0.1mF. All characteristics except noise voltage and ripple rejection ratio are measured using pulse techniques (tp voltage changes due to changes in internal temperature must be taken into account separately. 10ms, d 5%). Output 2) Test Conditions unless otherwise stated: TJ = 25C PMAX = 2W for H Package (TO-39) PMAX = 1.05W for J Package (CERDIP) PMAX = 15W for SG Package (SMD1) Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: sales@semelab.co.uk Website: http://www.semelab.co.uk Prelim.7/00 IP140MA SERIES IP140M SERIES IP78M00A SERIES IP78M00 SERIES ELECTRICAL CHARACTERISTICS Parameter Test Conditions IO = 100mA VO Output Voltage VIN = 23V IP78M15A IP140MA-15 Min. Typ. Max. IP78M15 IP140M-15 Min. Typ. Max. 14.85 15.15 14.40 15.45 14.25 15 PD PMAX 14.55 IO = 200mA DVO Load Regulation IQ Quiescent Current 22 60 4 22 30 4 22 150 12 75 150 mV 4 6 6 mA 0.1 0.5 VIN = 20V to 30V VIN = 20V to 26V IO = 5mA to 500mA VIN = 23V TJ = -55 to 150C VIN = 23V IO = 350mA TJ = -55 to 150C IO = 5mA to 500mA DIQ Quiescent Current VIN = 23V TJ = -55 to 150C Change IO = 200mA VIN = 18V to 30V Output Noise Voltage DVIN DVO Ripple Rejection Dropout Voltage f = 10Hz to 100kHz f = 120Hz IO = 300mA VIN = 18.5V to IO = 100mA 28.5V TJ = -55 to 150C Short Circuit Current VIN = 35V Ipk Peak Output Current VIN = 23V Average Temperature Coefficient of VO 0.2 0.8 90 600 IO = 5mA 0.5 0.8 90 57 70 54 57 70 54 2 2.5 300 600 1.0 1.4 1.5 6.0 IO = 350mA Isc 4 mV mA TJ = -55 to 150C VN V 4 TJ = -55 to 150C IO = 500mA 15.75 TJ = -55 to 150C VIN = 17.5V to 30V Line Regulation 15.60 IO = 5mA to 350mA VIN = 18V to 30V DVO 15 Units 0.7 0.7 600 mV dB 2.5 V 300 600 mA 1.0 1.6 A 1.5 mV C 1) All characteristics are measured with a capacitor across the input of 0.22mF and a capacitor across the output of 0.1mF. All characteristics except noise voltage and ripple rejection ratio are measured using pulse techniques (tp voltage changes due to changes in internal temperature must be taken into account separately. 10ms, d 5%). Output 2) Test Conditions unless otherwise stated: TJ = 25C PMAX = 2W for H Package (TO-39) PMAX = 1.05W for J Package (CERDIP) PMAX = 15W for SG Package (SMD1) Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: sales@semelab.co.uk Website: http://www.semelab.co.uk Prelim.7/00