MCC Features * * * * RMB2S THRU RMB4S omponents 20736 Marilla Street Chatsworth !"# $ % !"# 1/2 Amp Fast Recovery Glass Passivated Bridge Rectifier 200 to 400 Volts Surface Mount Package Glass Passivated Diode Construction Moisture Resistant Epoxy Case Fast Recovery, Low Switching Loss Maximum Ratings * * MBS-1 Operating Temperature: -55 to +150 Storage Temperature: -55 to +150 MCC Part Number Device Marking RMB2S RMB4S RB2S RB4S Maximum Recurrent Peak Reverse Voltage 100V 200V Maximum RMS Voltage 70V 140V Maximum DC Blocking Voltage 100V 200V Typical Thermal Resistance Per Leg Typical Junction Capacitance Maximum Reverse Recovery Time Rating For Fusing IFSM 0.5A (2) 0.8A 30A + F C A (1) IF(AV) D B E Electrical Characteristics @ 25 Unless Otherwise Specified Average Forward Current Peak Forward Surge Current Maximum Instantaneous Forward Voltage Maximum DC Reverse Current At Rated DC Blocking Voltage - TA = 30 Notch in case K 8.3ms, half sine M VF 1.25V IFM = 0.4A; TA = 25 J G H N L IR 5.0A 100A RJA RJA RJL 85/W(1) 70/W(2) 20/W(1) CJ 13pF trr 150ns 2 5.0A s It 2 TA = 25 TA = 125 PC board with 12mm2 copper pads Measured at 1.0MHz, VR=4.0V IF=0.5A, IR=1.0A, Irr=0.25A t<8.30ms (1) On glass epoxy P.C.B. mounted on 0.05 x 0.05"(1.3 x 1.3mm) pads (2) On aluminum substrate P.C.B. with an area of 0.8" x 0.8"(20 x 20mm) mounted on 0.05 x 0.05"(1.3x 1.3mm) solder pad K L M N .252 .017 .090 .004 .021 .058 .195 .110 .039 .008 INCHES .272 .029 .106 .008 .023 .062 .205 .114 .049 .014 MM 6.40 0.45 2.30 0.10 0.53 1.47 4.95 2.80 0.99 0.15 6.91 0.75 2.70 0.20 0.58 1.57 5.21 2.90 1.24 0.35 www.mccsemi.com Revision: 3 2003/04/30 MCC RMB2S thru RMB4S Fig. 2 - Maximum Non-Repetitive Peak Forward Surge Current 35 0.8 Peak Forward Surge Current (A) Average Forward Rectified Current (A) Fig. 1 - Maximum Forward Current Derating Curve 0.7 Aluminum Substrate 0.6 0.5 0.4 Glass Epoxy P.C.B. 0.3 0.2 0.1 25 20 f = 60Hz f = 50Hz 15 10 5.0 1.0 Cycle Resistive or Inductive Load 0 0 0 20 40 80 60 100 120 140 1 160 100 10 Ambient Temperature (C) Number of Cycles Fig. 3 - Typical Instantaneous Forward Characteristics Fig. 4 - Typical Reverse Leakage Characteristics Per Leg 100 Instantaneous Reverse Leakage Current (A) 10 Instantaneous Forward Current (A) TA = 40C Single Half Sine-Wave (JEDEC Method) 30 Pulse Width = 300 s 1% Duty Cycle TJ = 125C 10 1 TJ = 150C TJ = 25C 0.1 1 0.1 TJ = 25C 0.01 0.01 0.2 0.4 0.6 0.8 1.2 1.0 1.4 Instantaneous Forward Voltage (V) 0 20 40 60 80 100 Percent of Rated Peak Reverse Voltage (%) Fig. 5 - Typical Junction Capacitance Junction Capacitance (pF) 30 TJ = 25C f = 1.0 MHz Vsig = 50mVp-p 25 20 15 10 5.0 0 0.1 1 10 100 200 Reverse Voltage (V) www.mccsemi.com Revision: 3 2003/04/30