ADVANCE 512Mb: x4, x8, x16 DDR SDRAM DOUBLE DATA RATE (DDR) SDRAM MT46V128M4 - 32 Meg x 4 x 4 banks MT46V64M8 - 16 Meg x 8 x 4 banks MT46V32M16 - 8 Meg x 16 x 4 banks For the latest data sheet revisions, please refer to the Micron Web site: www.micronsemi.com/datasheets/ddrsdramds.html FEATURES OPTIONS MARKING * Configuration 128 Meg x 4 (32 Meg x 4 x 4 banks) 128M4 64 Meg x 8 (16 Meg x 8 x 4 banks) 64M8 32 Meg x 16 (8 Meg x 16 x 4 banks) 32M16 * x16 IOL / IOH Drive Full Drive Only D1 Reduced Drive Only D2 Programmable full or reduced drive D3 * Plastic Package - OCPL 66-pin TSOP (standard 22.3mm length) T G 66-pin TSOP (extended 27mm length) TH (400 mil width, 0.65mm pin pitch) * Timing - Cycle Time 7.5ns @ CL = 2 (DDR266A+)1 -7 7.5ns @ CL = 2.5 (DDR266B)2 -75 -8 10ns @ CL = 2 (DDR200)3 * Self Refresh Standard none Low Power L 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 128 Meg x 4 Configuration 32 Meg x 4 x 4 banks Refresh Count Row Addressing BankAddressing Column Addressing TG Package x4 x8 x16 VDD VDD VDD NC DQ0 DQ0 VDDQ VDDQ VDDQ NC DQ1 NC DQ0 DQ1 DQ2 VSSQ VSSQ VssQ NC DQ3 NC NC DQ2 DQ4 VDDQ VDDQ VDDQ NC NC DQ5 DQ1 DQ3 DQ6 VSSQ VSSQ VssQ NC DQ7 NC NC NC NC VDDQ VDDQ VDDQ NC NC LDQS NC NC NC VDD VDD VDD DNU DNU DNU NC NC LDM WE# WE# WE# CAS# CAS# CAS# RAS# RAS# RAS# CS# CS# CS# NC NC NC BA0 BA0 BA0 BA1 BA1 BA1 A10/AP A10/AP A10/AP A0 A0 A0 A1 A1 A1 A2 A2 A2 A3 A3 A3 VDD VDD VDD TH Package PIN ASSIGNMENT (TOP VIEW) 66-Pin TSOP * VDD = +2.5V 0.2V, VDDQ = +2.5V 0.2V * Bidirectional data strobe (DQS) transmitted/ received with data, i.e., source-synchronous data capture (x16 has two - one per byte) * Internal, pipelined double-data-rate (DDR) architecture; two data accesses per clock cycle * Differential clock inputs (CK and CK#) * Commands entered on each positive CK edge * DQS edge-aligned with data for READs; centeraligned with data for WRITEs * DLL to align DQ and DQS transitions with CK * Four internal banks for concurrent operation * Data mask (DM) for masking write data (x16 has two - one per byte) * Programmable burst lengths: 2, 4, or 8 * Auto precharge option * Auto Refresh and Self Refresh Modes * Longer lead TSOP for improved reliability (OCPL) * 2.5V I/O (SSTL_2 compatible) 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 64 Meg x 8 x16 VSS DQ15 VSSQ DQ14 DQ13 VDDQ DQ12 DQ11 VSSQ DQ10 DQ9 VDDQ DQ8 NC VSSQ UDQS DNU VREF VSS UDM CK# CK CKE NC A12 A11 A9 A8 A7 A6 A5 A4 VSS x8 VSS DQ7 VSSQ NC DQ6 VDDQ NC DQ5 VSSQ NC DQ4 VDDQ NC NC VSSQ DQS DNU VREF VSS DM CK# CK CKE NC A12 A11 A9 A8 A7 A6 A5 A4 VSS x4 VSS NC VSSQ NC DQ3 VDDQ NC NC VSSQ NC DQ2 VDDQ NC NC VSSQ DQS DNU VREF VSS DM CK# CK CKE NC A12 A11 A9 A8 A7 A6 A5 A4 VSS 32 Meg x 16 16 Meg x 8 x 4 banks 8 Meg x 16 x 4 banks 8K 8K(A0-A12) 4 (BA0, BA1) 8K 8K(A0-A12) 4 (BA0, BA1) 8K 8K(A0-A12) 4 (BA0, BA1) 4K(A0-A9,A11,A12) 2K(A0-A9, A11) 1K(A0-A9) KEY TIMING PARAMETERS SPEED NOTE: 1. Supports PC2100 modules with 2-2-2 timing 2. Supports PC2100 modules with 2.5-3-3 timing 3. Supports PC1600 modules with 2-2-2 timing CLOCK RATE GRADE CL = 2** CL = 2.5** -7 -75 -8 133 MHz 100 MHz 100 MHz 143 MHz 133 MHz 125 MHz DATA-OUT ACCESS WINDOW* WINDOW 2.5ns 2.5ns 3.4ns 0.75ns 0.75ns 0.8ns DQS-DQ SKEW +0.5ns +0.5ns +0.6ns *Minimum clock rate @ CL = 2 (-7, -8) and CL = 2.5 (-75) **CL = CAS (Read) Latency 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 1 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. PRODUCTS AND SPECIFICATIONS DISCUSSED HEREIN ARE FOR EVALUATION AND REFERENCE PURPOSES ONLY AND ARE SUBJECT TO CHANGE BY MICRON WITHOUT NOTICE. PRODUCTS ARE ONLY WARRANTED BY MICRON TO MEET MICRON'S PRODUCTION DATA SHEET SPECIFICATIONS. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM 256Mb DDR SDRAM PART NUMBERS (Note: xx= 7, 75, or 8) PART NUMBER MT46V128M4TH-xx MT46V128M4TH-xxL CONFIGURATION 128 Meg x 4 128 Meg x 4 I/O DRIVE LEVEL Full Drive Full Drive REFRESH OPTION Standard Low Power PACKAGE 66-pin TSOP (27mm) 66-pin TSOP (27mm) MT46V64M8TH-xx MT46V64M8TH-xxL 64 Meg x 8 64 Meg x 8 Full Drive Full Drive Standard Low Power 66-pin TSOP (27mm) 66-pin TSOP (27mm) MT46V32M16D1TH-xx MT46V32M16D1TH-xxL MT46V32M16D2TH-xx MT46V32M16D2TH-xxL MT46V32M16D3TH-xx MT46V32M16D3TH-xxL 32 Meg x 16 32 Meg x 16 32 Meg x 16 32 Meg x 16 32 Meg x 16 32 Meg x 16 Full Drive Full Drive Reduced Drive Reduced Drive Programmable Drive Programmable Drive Standard Low Power Standard Low Power Standard Low Power 66-pin TSOP (27mm) 66-pin TSOP (27mm) 66-pin TSOP (27mm) 66-pin TSOP (27mm) 66-pin TSOP (27mm) 66-pin TSOP (27mm) GENERAL DESCRIPTION tration of an ACTIVE command, which is then followed by a READ or WRITE command. The address bits registered coincident with the ACTIVE command are used to select the bank and row to be accessed. The address bits registered coincident with the READ or WRITE command are used to select the bank and the starting column location for the burst access. The DDR SDRAM provides for programmable READ or WRITE burst lengths of 2, 4, or 8 locations. An auto precharge function may be enabled to provide a selftimed row precharge that is initiated at the end of the burst access. As with standard SDR SDRAMs, the pipelined, multibank architecture of DDR SDRAMs allows for concurrent operation, thereby providing high effective bandwidth by hiding row precharge and activation time. An auto refresh mode is provided, along with a power-saving power-down mode. All inputs are compatible with the JEDEC Standard for SSTL_2. All full drive strength outputs are SSTL_2, Class II compatible. The 512Mb DDR SDRAM is a high-speed CMOS, dynamic random-access memory containing 536,870,912 bits. It is internally configured as a quadbank DRAM. The 512Mb DDR SDRAM uses a double data rate architecture to achieve high-speed operation. The double data rate architecture is essentially a 2n-prefetch architecture with an interface designed to transfer two data words per clock cycle at the I/O pins. A single read or write access for the 512Mb DDR SDRAM effectively consists of a single 2n-bit wide, one-clock-cycle data transfer at the internal DRAM core and two corresponding n-bit wide, one-half-clock-cycle data transfers at the I/O pins. A bidirectional data strobe (DQS) is transmitted externally, along with data, for use in data capture at the receiver. DQS is a strobe transmitted by the DDR SDRAM during READs and by the memory controller during WRITEs. DQS is edge-aligned with data for READs and center-aligned with data for WRITEs. The x16 offering has two data strobes, one for the lower byte and one for the upper byte. The 512Mb DDR SDRAM operates from a differential clock (CK and CK#); the crossing of CK going HIGH and CK# going LOW will be referred to as the positive edge of CK. Commands (address and control signals) are registered at every positive edge of CK. Input data is registered on both edges of DQS, and output data is referenced to both edges of DQS, as well as to both edges of CK. Read and write accesses to the DDR SDRAM are burst oriented; accesses start at a selected location and continue for a programmed number of locations in a programmed sequence. Accesses begin with the regis- 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 NOTE: 1. The functionality and the timing specifications discussed in this data sheet are for the DLL-enabled mode of operation. 2. Throughout the data sheet, the various figures and text refer to DQs as "DQ." The DQ term is to be interpreted as any and all DQ collectively, unless specifically stated otherwise. Additionally, the x16 is divided in to two bytes--the lower byte and upper byte. For the lower byte (DQ0 through DQ7) DM refers to LDM and DQS refers to LDQS; and for the upper byte (DQ8 through DQ15) DM refers to UDM and DQS refers to UDQS. 2 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM TABLE OF CONTENTS Functional Block Diagram - 128 Meg x 4 ............. Functional Block Diagram - 64 Meg x 8 ............... Functional Block Diagram - 32 Meg x 16 ............. Pin Descriptions ...................................................... 4 5 6 7 Functional Description ......................................... Initialization ...................................................... Register Definition ............................................. Mode Register ............................................... Burst Length ............................................ Burst Type ................................................ Read Latency ........................................... Operating Mode ...................................... Extended Mode Register ............................... DLL Enable/Disable ................................. 9 9 9 9 9 10 11 11 12 12 Commands ............................................................ Truth Table 1 (Commands) ....................................... Truth Table 1A (DM Operation) ................................. Deselect .............................................................. No Operation (NOP) .......................................... Load Mode Register ........................................... Active ................................................................ Read ................................................................ Write ................................................................ Precharge ........................................................... Auto Precharge .................................................. Burst Terminate ................................................. Auto Refresh ...................................................... Self Refresh ......................................................... 13 13 13 14 14 14 14 14 14 14 14 14 15 15 Operation .............................................................. Bank/Row Activation ....................................... Reads ................................................................ Read Burst .................................................... Consecutive Read Bursts .............................. Nonconsecutive Read Bursts ....................... Random Read Accesses ................................ Terminating a Read Burst ............................ Read to Write ............................................... Read to Precharge ......................................... Writes ................................................................ Write Burst .................................................... Consecutive Write to Write ......................... Nonconsecutive Write to Write .................. 16 16 17 18 19 20 21 23 24 25 26 27 28 29 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 Random Writes ............................................ Write to Read - Uninterrupting .................. Write to Read - Interrupting ....................... Write to Read - Odd, Interrupting ............. Write to Precharge - Uninterrupting .......... Write to Precharge - Interrupting ............... Write to Precharge - Odd, Interrupting ...... Precharge ........................................................... Power-Down ..................................................... Truth Table 2 (CKE) ................................................. Truth Table 3 (Current State, Same Bank) ..................... Truth Table 4 (Current State, Different Bank) ................. 30 31 32 33 34 35 36 37 37 38 39 41 Operating Conditions Absolute Maximum Ratings .................................... DC Electrical and Operating Conditions ..................... AC Input Operating Conditions ............................. Capacitance - x4, x8 .............................................. IDD Specifications and Conditions - x4, x8 ........... Capacitance - x16 .................................................. IDD Specifications and Conditions - x16 ............... AC Electrical Characteristics (Timing Table) .......... Slew Rate Derating Table ....................................... Data Valid Window Derating ............................... 43 43 43 44 45 46 47 48 49 51 Voltage and Timing Waveforms Nominal Output Drive Curves ......................... Reduced Output Drive Curves (x16 only) ........ Output Timing - tDQSQ and tQH - x4, x8 ...... Output Timing - tDQSQ and tQH - x16 .......... Output Timing - tAC and tDQSCK ................. Input Timing ..................................................... Input Voltage .................................................... Initialize and Load Mode Registers .................. Power-Down Mode .......................................... Auto Refresh Mode ........................................... Self Refresh Mode ............................................. Reads Bank Read - Without Auto Precharge ........ Bank Read - With Auto Precharge .............. Writes Bank Write - Without Auto Precharge ....... Bank Write - With Auto Precharge ............. Write - DM Operation ................................ 66-pin TSOP (TH) dimensions ............................... 66-pin TSOP (TG) dimensions ............................... 3 54 55 56 57 58 58 59 60 61 62 63 64 65 66 67 68 69 70 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM FUNCTIONAL BLOCK DIAGRAM 128 Meg x 4 CKE CK# CK COMMAND DECODE CS# WE# CAS# RAS# CONTROL LOGIC BANK3 BANK2 BANK1 MODE REGISTERS REFRESH 13 COUNTER 13 ROWADDRESS MUX 13 13 BANK0 ROWADDRESS LATCH & DECODER 8192 CK BANK0 MEMORY ARRAY (8,192 x 2,048 x 8) DLL DATA 4 8 READ LATCH SENSE AMPLIFIERS 4 MUX DRVRS 4 1 DQS GENERATOR 8192 DQ0 DQ3, DM COL0 I/O GATING DM MASK LOGIC 2 A0-A12, BA0, BA1 15 ADDRESS REGISTER 2 1 DQS 1 MASK 2048 (x8) COLUMN DECODER 12 8 BANK CONTROL LOGIC COLUMNADDRESS COUNTER/ LATCH DQS INPUT REGISTERS 11 8 WRITE FIFO & DRIVERS ck out CK ck in 1 1 1 4 4 2 8 RCVRS 4 4 4 DATA 1 1 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 4 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM FUNCTIONAL BLOCK DIAGRAM 64 Meg x 8 CKE CK# CK COMMAND DECODE CS# WE# CAS# RAS# CONTROL LOGIC BANK3 BANK2 BANK1 MODE REGISTERS REFRESH 13 COUNTER 13 ROWADDRESS MUX 13 13 BANK0 ROWADDRESS LATCH & DECODER 8192 CK BANK0 MEMORY ARRAY (8192 x 1024 x 16) READ LATCH SENSE AMPLIFIERS 8 MUX DRVRS 8 I/O GATING DM MASK LOGIC A0-A12, BA0, BA1 15 ADDRESS REGISTER 2 16 1 DQS 1 MASK 1024 (x16) COLUMN DECODER 11 DQ0 DQ7, DM DQS INPUT REGISTERS BANK CONTROL LOGIC COLUMNADDRESS COUNTER/ LATCH 1 DQS GENERATOR 8192 2 DLL DATA 8 16 10 16 WRITE FIFO & DRIVERS ck out CK ck in 1 1 1 8 8 2 16 RCVRS 8 8 8 DATA 1 1 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 5 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM FUNCTIONAL BLOCK DIAGRAM 32 Meg x 16 CKE CK# CK COMMAND DECODE CS# WE# CAS# RAS# CONTROL LOGIC BANK3 BANK2 BANK1 REFRESH COUNTER 13 MODE REGISTERS ROWADDRESS MUX 13 13 13 BANK0 ROWADDRESS LATCH & DECODER 8192 CK BANK0 MEMORY ARRAY (8,192 x 512 x 32) READ LATCH SENSE AMPLIFIERS 16 MUX DRVRS 16 I/O GATING DM MASK LOGIC A0-A12, BA0, BA1 15 ADDRESS REGISTER 2 2 COLUMN DECODER COLUMNADDRESS COUNTER/ LATCH 9 WRITE FIFO & DRIVERS ck out CK ck in LDQS UDQS 2 MASK 32 DQ0 DQ15, LDM, UDM DQS INPUT REGISTERS 32 BANK CONTROL LOGIC 512 (x32) 10 2 DQS GENERATOR 8192 2 DLL DATA 16 32 2 2 2 16 16 4 32 RCVRS 16 16 16 DATA 2 1 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 6 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM PIN DESCRIPTIONS TSOP PIN NUMBERS SYMBOL TYPE 45, 46 CK, CK# Input Clock: CK and CK# are differential clock inputs. All address and control input signals are sampled on the crossing of the positive edge of CK and negative edge of CK#. Output data (DQs and DQS) is referenced to the crossings of CK and CK#. DESCRIPTION 44 CKE Input Clock Enable: CKE HIGH activates and CKE LOW deactivates the internal clock, input buffers and output drivers. Taking CKE LOW provides PRECHARGE POWER-DOWN and SELF REFRESH operations (all banks idle), or ACTIVE POWER-DOWN (row ACTIVE in any bank). CKE is synchronous for POWER-DOWN entry and exit, and for SELF REFRESH entry. CKE is asynchronous for SELF REFRESH exit and for disabling the outputs. CKE must be maintained HIGH throughout read and write accesses. Input buffers (excluding CK, CK# and CKE) are disabled during POWERDOWN. Input buffers (excluding CKE) are disabled during SELF REFRESH. CKE is an SSTL_2 input but will detect an LVCMOS LOW level after VDD is applied. 24 CS# Input Chip Select: CS# enables (registered LOW) and disables (registered HIGH) the command decoder. All commands are masked when CS# is registered HIGH. CS# provides for external bank selection on systems with multiple banks. CS# is considered part of the command code. 23, 22, 21 RAS#, CAS#, WE# Input Command Inputs: RAS#, CAS#, and WE# (along with CS#) define the command being entered. 47 20, 47 DM LDM, UDM Input Input Data Mask: DM is an input mask signal for write data. Input data is masked when DM is sampled HIGH along with that input data during a WRITE access. DM is sampled on both edges of DQS. Although DM pins are input-only, the DM loading is designed to match that of DQ and DQS pins. For the x16 , LDM is DM for DQ0DQ7 and UDM is DM for DQ8-DQ15. Pin 20 is a NC on x4 and x8 26, 27 BA0, BA1 Input Bank Address Inputs: BA0 and BA1 define to which bank an ACTIVE, READ, WRITE, or PRECHARGE command is being applied. 29-32, 35-40, 28, 41, 42 A0-A12 Input Address Inputs: Provide the row address for ACTIVE commands, and the column address and auto precharge bit (A10) for READ/WRITE commands, to select one location out of the memory array in the respective bank. A10 sampled during a PRECHARGE command determines whether the PRECHARGE applies to one bank (A10 LOW, bank selected by BA0, BA1) or all banks (A10 HIGH). The address inputs also provide the op-code during a MODE REGISTER SET command. BA0 and BA1 define which mode register (mode register or extended mode register) is loaded during the LOAD MODE REGISTER command. 2, 4, 5, 7, 8, 10, 11, 13, 54, 56, 57, 59, 60, 62, 63, 65 DQ0-15 I/O Data Input/Output: Data bus for x16 (4, 7, 10, 13, 54, 57, 60, and 63 are NC for x8), (2, 4, 7, 8,10, 13, 54, 57, 59, 60, 63, and 65 for x4). (continued on next page) 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 7 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM PIN DESCRIPTIONS (continued) TSOP PIN NUMBERS 2, 5, 8, 11, 56, 59, 62, 65 5, 11, 56, 62 SYMBOL DQ0-7 DQ0-3 TYPE I/O I/O DESCRIPTION Data Input/Output: Data bus for x8 (2, 8, 59 and 65 are NC for x4). Data Input/Output: Data bus for x4. 51 16, 51 DQS LDQS, UDQS I/O Data Strobe: Output with read data, input with write data. DQS is edge-aligned with read data, centered in write data. It is used to capture data. For the x16 , LDQS is DQS for DQ0-DQ7 and UDQS is DQS for DQ8-DQ15. Pin 16 is NC on x4 and x8. 50 DNU - 3, 9, 15, 55, 61 VDDQ Supply Do Not Use: Must float to minimize noise. DQ Power Supply: +2.5V 0.2V. Isolated on the die for improved noise immunity. 6, 12, 52, 58, 64 VSSQ Supply DQ Ground. Isolated on the die for improved noise immunity. 1, 18, 33 VDD Supply Power Supply: +2.5V 0.2V. 34, 48, 66 VSS Supply Ground. 49 VREF Supply SSTL_2 reference voltage. 14, 17, 19, 25, 43, 53 NC - No Connect: These pins should be left unconnected. RESERVED NC PINS1 TSOP PIN NUMBERS 17 SYMBOL A13 TYPE I DESCRIPTION Address input for 1Gb devices. NOTE: 1. NC pins not listed may also be reserved for other uses now or in the future. This table simply defines specific NC pins deemed to be of importance. 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 8 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM FUNCTIONAL DESCRIPTION The 512Mb DDR SDRAM is a high-speed CMOS, dynamic random-access memory containing 536,870,912 bits. The 512Mb DDR SDRAM is internally configured as a quad-bank DRAM. The 512Mb DDR SDRAM uses a double data rate architecture to achieve high-speed operation. The double data rate architecture is essentially a 2n-prefetch architecture, with an interface designed to transfer two data words per clock cycle at the I/O pins. A single read or write access for the 512Mb DDR SDRAM consists of a single 2n-bit wide, one-clock-cycle data transfer at the internal DRAM core and two corresponding n-bit wide, one-half-clock-cycle data transfers at the I/O pins. Read and write accesses to the DDR SDRAM are burst oriented; accesses start at a selected location and continue for a programmed number of locations in a programmed sequence. Accesses begin with the registration of an ACTIVE command, which is then followed by a READ or WRITE command. The address bits registered coincident with the ACTIVE command are used to select the bank and row to be accessed (BA0, BA1 select the bank; A0-A12 select the row). The address bits registered coincident with the READ or WRITE command are used to select the starting column location for the burst access. Prior to normal operation, the DDR SDRAM must be initialized. The following sections provide detailed information covering device initialization, register definition, command descriptions and device operation. should be brought HIGH. Following the NOP command, a PRECHARGE ALL command should be applied. Next a LOAD MODE REGISTER command should be issued for the extended mode register (BA1 LOW and BA0 HIGH) to enable the DLL, followed by another LOAD MODE REGISTER command to the mode register (BA0/BA1 both LOW) to reset the DLL and to program the operating parameters. Two-hundred clock cycles are required between the DLL reset and any READ command. A PRECHARGE ALL command should then be applied, placing the device in the all banks idle state. Once in the idle state, two AUTO REFRESH cycles must be performed (tRFC must be satisfied.) Additionally, a LOAD MODE REGISTER command for the mode register with the reset DLL bit deactivated (i.e., to program operating parameters without resetting the DLL) is required. Following these requirements, the DDR SDRAM is ready for normal operation. Register Definition MODE REGISTER The mode register is used to define the specific mode of operation of the DDR SDRAM. This definition includes the selection of a burst length, a burst type, a CAS latency and an operating mode, as shown in Figure 1. The mode register is programmed via the MODE REGISTER SET command (with BA0 = 0 and BA1 = 0) and will retain the stored information until it is programmed again or the device loses power (except for bit A8, which is self-clearing). Reprogramming the mode register will not alter the contents of the memory, provided it is performed correctly. The mode register must be loaded (reloaded) when all banks are idle and no bursts are in progress, and the controller must wait the specified time before initiating the subsequent operation. Violating either of these requirements will result in unspecified operation. Mode register bits A0-A2 specify the burst length, A3 specifies the type of burst (sequential or interleaved), A4-A6 specify the CAS latency, and A7-A12 specify the operating mode. Initialization DDR SDRAMs must be powered up and initialized in a predefined manner. Operational procedures other than those specified may result in undefined operation. Power must first be applied to VDD and VDDQ simultaneously, and then to VREF (and to the system VTT). VTT must be applied after VDDQ to avoid device latch-up, which may cause permanent damage to the device. VREF can be applied any time after VDDQ but is expected to be nominally coincident with VTT. Except for CKE, inputs are not recognized as valid until after VREF is applied. CKE is an SSTL_2 input but will detect an LVCMOS LOW level after VDD is applied. Maintaining an LVCMOS LOW level on CKE during power-up is required to ensure that the DQ and DQS outputs will be in the High-Z state, where they will remain until driven in normal operation (by a read access). After all power supply and reference voltages are stable, and the clock is stable, the DDR SDRAM requires a 200s delay prior to applying an executable command. Once the 200s delay has been satisfied, a DESELECT or NOP command should be applied, and CKE 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 Burst Length Read and write accesses to the DDR SDRAM are burst oriented, with the burst length being programmable, as shown in Figure 1. The burst length determines the maximum number of column locations that can be accessed for a given READ or WRITE command. Burst lengths of 2, 4, or 8 locations are available for both the sequential and the interleaved burst types. 9 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM Reserved states should not be used, as unknown operation or incompatibility with future versions may result. When a READ or WRITE command is issued, a block of columns equal to the burst length is effectively selected. All accesses for that burst take place within this block, meaning that the burst will wrap within the block if a boundary is reached. The block is uniquely selected by A1-Ai when the burst length is set to two, by A2-Ai when the burst length is set to four and by A3-Ai when the burst length is set to eight (where Ai is the most significant column address bit for a given configuration). The remaining (least significant) address BA0 BA1 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 14 13 12 11 10 9 8 Operating Mode 0* 0* 6 5 4 3 2 1 0 CAS Latency BT Burst Length 7 bit(s) is (are) used to select the starting location within the block. The programmed burst length applies to both READ and WRITE bursts. Burst Type Accesses within a given burst may be programmed to be either sequential or interleaved; this is referred to as the burst type and is selected via bit M3. The ordering of accesses within a burst is determined by the burst length, the burst type and the starting column address, as shown in Table 1. Table 1 Burst Definition Address Bus Mode Register (Mx) Burst Length * M14 and M13 (BA0 and BA1) must be "0, 0" to select the base mode register (vs. the extended mode register). Burst Length M2 M1 M0 M3 = 0 M3 = 1 0 0 0 Reserved Reserved 0 0 1 2 2 0 1 0 4 4 0 1 1 8 8 1 0 0 Reserved Reserved 1 0 1 Reserved Reserved 1 1 0 Reserved Reserved 1 1 1 Reserved Reserved 4 Burst Type M3 0 Sequential 1 Interleaved 8 CAS Latency M6 M5 M4 0 0 0 Reserved 0 0 1 Reserved 0 1 0 2 0 1 1 Reserved 1 0 0 Reserved 1 0 1 Reserved 1 1 0 2.5 1 1 1 Reserved M12 M11 M10 M9 M8 M7 2 M6-M0 0 0 0 0 0 Valid Normal Operation 0 0 0 0 1 0 Valid Normal Operation/Reset DLL - - - - - - - All other states reserved Figure 1 Mode Register Definition 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 A0 0 1 A1 A0 0 0 0 1 1 0 1 1 A2 A1 A0 0 0 0 0 0 1 0 1 0 0 1 1 1 0 0 1 0 1 1 1 0 1 1 1 Order of Accesses Within a Burst Type = Sequential Type = Interleaved 0-1 1-0 0-1 1-0 0-1-2-3 1-2-3-0 2-3-0-1 3-0-1-2 0-1-2-3 1-0-3-2 2-3-0-1 3-2-1-0 0-1-2-3-4-5-6-7 1-2-3-4-5-6-7-0 2-3-4-5-6-7-0-1 3-4-5-6-7-0-1-2 4-5-6-7-0-1-2-3 5-6-7-0-1-2-3-4 6-7-0-1-2-3-4-5 7-0-1-2-3-4-5-6 0-1-2-3-4-5-6-7 1-0-3-2-5-4-7-6 2-3-0-1-6-7-4-5 3-2-1-0-7-6-5-4 4-5-6-7-0-1-2-3 5-4-7-6-1-0-3-2 6-7-4-5-2-3-0-1 7-6-5-4-3-2-1-0 NOTE: 1. For a burst length of two, A1-Ai select the twodata-element block; A0 selects the first access within the block. 2. For a burst length of four, A2-Ai select the fourdata-element block; A0-A1 select the first access within the block. 3. For a burst length of eight, A3-Ai select the eightdata-element block; A0-A2 select the first access within the block. 4. Whenever a boundary of the block is reached within a given sequence above, the following access wraps within the block. Operating Mode 0 Starting Column Address 10 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM Read Latency The READ latency is the delay, in clock cycles, between the registration of a READ command and the availability of the first bit of output data. The latency can be set to 2, or 2.5 clocks, as shown in Figure 2. If a READ command is registered at clock edge n, and the latency is m clocks, the data will be available nominally coincident with clock edge n + m. Table 2 indicates the operating frequencies at which each CAS latency setting can be used. Reserved states should not be used as unknown operation or incompatibility with future versions may result. T0 T1 T2 READ NOP NOP T2n T3 Table 2 CAS Latency (CL) ALLOWABLE OPERATING FREQUENCY (MHz) CK NOP CL = 2 DQS DQ CK# T0 T1 T2 READ NOP NOP T2n T3 T3n CK COMMAND CL = 2 CL = 2.5 -7 83 f 133 83 f 143 -75 83 f 100 83 f 133 -8 83 f 100 83 f 125 Operating Mode The normal operating mode is selected by issuing a MODE REGISTER SET command with bits A7-A12 each set to zero, and bits A0-A6 set to the desired values. A DLL reset is initiated by issuing a MODE REGISTER SET command with bits A7 and A9-A12 each set to zero, bit A8 set to one, and bits A0-A6 set to the desired values. Although not required by the Micron device, JEDEC specifications recommend when a LOAD MODE REGISTER command is issued to reset the DLL, it should always be followed by a LOAD MODE REGISTER command to select normal operating mode. All other combinations of values for A7-A12 are reserved for future use and/or test modes. Test modes and reserved states should not be used because unknown operation or incompatibility with future versions may result. T3n CK# COMMAND SPEED NOP CL = 2.5 DQS DQ Burst Length = 4 in the cases shown Shown with nominal tAC and nominal tDSDQ TRANSITIONING DATA DON'T CARE Figure 2 CAS Latency 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 11 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM EXTENDED MODE REGISTER The extended mode register controls functions beyond those controlled by the mode register; these additional functions are DLL enable/disable and output drive strength. These functions are controlled via the bits shown in Figure 3. The extended mode register is programmed via the LOAD MODE REGISTER command to the mode register (with BA0 = 1 and BA1 = 0) and will retain the stored information until it is programmed again or the device loses power. The enabling of the DLL should always be followed by a LOAD MODE REGISTER command to the mode register (BA0/BA1 both LOW) to reset the DLL. The extended mode register must be loaded when all banks are idle and no bursts are in progress, and the controller must wait the specified time before initiating any subsequent operation. Violating either of these requirements could result in unspecified operation. BA0 BA1 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 14 13 12 11 10 9 8 7 6 5 Operating Mode 11 01 4 3 2 1 0 Extended Mode Register (Ex) QFC DS DLL E0 DLL 0 Enable 1 Disable E12 E12 E11 E10 E9 E8 E7 E6 E5 E4 E3 E2, E1, E0 Drive Strength 0 Normal 1 Reduced E23 Output Drive Strength The normal drive strength for all outputs are specified to be SSTL2, Class II. The x16 supports an option for reduced drive. This option is intended for the support of the lighter load and/or point-to-point environments. The selection of the reduced drive strength will alter the DQs and DQSs from SSTL2, Class II drive strength to a reduced drive strength, which is approximately 54% of the SSTL2, Class II drive strength. Micron will support these x16 options: 1) Full drive strength only (not programmable), 2) Reduced drive strength only (not programable), and 3) Programmable full or reduced drive strength. Address Bus QFC Function 0 Disabled - Reserved Operating Mode 0 0 0 0 0 0 0 0 0 0 Valid Reserved - - - - - - - - - - - Reserved NOTE: 1. E14 and E13 (BA0 and BA1) must be "1, 0" to select the Extended Mode Register (vs. the base Mode Register). 2. The reduced drive strength option is not supported on the x4 and x8 versions: and is only available on the D3 version of the x16 device. 3. The QFC# option is not supported. Figure 3 Extended Mode Register Definition DLL Enable/Disable The DLL must be enabled for normal operation. DLL enable is required during power-up initialization and upon returning to normal operation after having disabled the DLL for the purpose of debug or evaluation. (When the device exits self refresh mode, the DLL is enabled automatically.) Any time the DLL is enabled, 200 clock cycles must occur before a READ command can be issued. 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 12 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM COMMANDS Truth Table 1 provides a quick reference of available commands. This is followed by a verbal description of each command. Two additional Truth Tables appear following the Operation section; these tables provide current state/next state information. TRUTH TABLE 1 - COMMANDS (Note: 1) NAME (FUNCTION) CS# RAS# CAS# WE# ADDR NOTES DESELECT (NOP) H X X X X 9 NO OPERATION (NOP) L H H H X 9 ACTIVE (Select bank and activate row) L L H H Bank/Row 3 READ (Select bank and column, and start READ burst) L H L H Bank/Col 4 WRITE (Select bank and column, and start WRITE burst) L H L L Bank/Col 4 BURST TERMINATE L H H L X 8 PRECHARGE (Deactivate row in bank or banks) L L H L Code 5 AUTO REFRESH or SELF REFRESH (Enter self refresh mode) L L L H X 6, 7 LOAD MODE REGISTER L L L L Op-Code 2 TRUTH TABLE 1A - DM OPERATION (Note: 10) NAME (FUNCTION) DM DQs Write Enable L Valid Write Inhibit H X NOTES NOTE: 1. CKE is HIGH for all commands shown except SELF REFRESH. 2. BA0-BA1 select either the mode register or the extended mode register (BA0 = 0, BA1 = 0 select the mode register; BA0 = 1, BA1 = 0 select extended mode register; other combinations of BA0-BA1 are reserved). A0-A12 provide the opcode to be written to the selected mode register. 3. BA0-BA1 provide bank address and A0-A12 provide row address. 4. BA0-BA1 provide bank address; A0-Ai provide column address (where i = 9 for x16, 9,11 for x8, and 9, 11, 12 for x4); A10 HIGH enables the auto precharge feature (nonpersistent), and A10 LOW disables the auto precharge feature. 5. A10 LOW: BA0-BA1 determine which bank is precharged. A10 HIGH: all banks are precharged and BA0-BA1 are "Don't Care." 6. This command is AUTO REFRESH if CKE is HIGH, SELF REFRESH if CKE is LOW. 7. Internal refresh counter controls row addressing; all inputs and I/Os are "Don't Care" except for CKE. 8. Applies only to read bursts with auto precharge disabled; this command is undefined (and should not be used) for READ bursts with auto precharge enabled and for WRITE bursts. 9. DESELECT and NOP are functionally interchangeable. 10. Used to mask write data; provided coincident with the corresponding data. 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 13 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM DESELECT The DESELECT function (CS# HIGH) prevents new commands from being executed by the DDR SDRAM. The DDR SDRAM is effectively deselected. Operations already in progress are not affected. appearing on the DQs is written to the memory array subject to the DM input logic level appearing coincident with the data. If a given DM signal is registered LOW, the corresponding data will be written to memory; if the DM signal is registered HIGH, the corresponding data inputs will be ignored, and a WRITE will not be executed to that byte/column location. NO OPERATION (NOP) The NO OPERATION (NOP) command is used to instruct the selected DDR SDRAM to perform a NOP (CS# LOW). This prevents unwanted commands from being registered during idle or wait states. Operations already in progress are not affected. PRECHARGE The PRECHARGE command is used to deactivate the open row in a particular bank or the open row in all banks. The bank(s) will be available for a subsequent row access a specified time (tRP) after the PRECHARGE command is issued. Input A10 determines whether one or all banks are to be precharged, and in the case where only one bank is to be precharged, inputs BA0, BA1 select the bank. Otherwise BA0, BA1 are treated as "Don't Care." Once a bank has been precharged, it is in the idle state and must be activated prior to any READ or WRITE commands being issued to that bank. A PRECHARGE command will be treated as a NOP if there is no open row in that bank (idle state), or if the previously open row is already in the process of precharging. LOAD MODE REGISTER The mode registers are loaded via inputs A0-A12. See mode register descriptions in the Register Definition section. The LOAD MODE REGISTER command can only be issued when all banks are idle, and a subsequent executable command cannot be issued until tMRD is met. ACTIVE The ACTIVE command is used to open (or activate) a row in a particular bank for a subsequent access. The value on the BA0, BA1 inputs selects the bank, and the address provided on inputs A0-A12 selects the row. This row remains active (or open) for accesses until a PRECHARGE command is issued to that bank. A PRECHARGE command must be issued before opening a different row in the same bank. AUTO PRECHARGE Auto precharge is a feature which performs the same individual-bank precharge function described above, but without requiring an explicit command. This is accomplished by using A10 to enable auto precharge in conjunction with a specific READ or WRITE command. A precharge of the bank/row that is addressed with the READ or WRITE command is automatically performed upon completion of the READ or WRITE burst. Auto precharge is nonpersistent in that it is either enabled or disabled for each individual READ or WRITE command. Auto precharge ensures that the precharge is initiated at the earliest valid stage within a burst. This "earliest valid stage" is determined as if an explicit PRECHARGE command was issued at the earliest possible time, without violating tRAS (MIN), as described for each burst type in the Operation section of this data sheet. The user must not issue another command to the same bank until the precharge time (tRP) is completed. READ The READ command is used to initiate a burst read access to an active row. The value on the BA0, BA1 inputs selects the bank, and the address provided on inputs A0-Ai (where i = 9 for x16; 9, 11 for x8; or 9, 11, and 12 for x4) selects the starting column location. The value on input A10 determines whether or not auto precharge is used. If auto precharge is selected, the row being accessed will be precharged at the end of the READ burst; if auto precharge is not selected, the row will remain open for subsequent accesses. WRITE The WRITE command is used to initiate a burst write access to an active row. The value on the BA0, BA1 inputs selects the bank, and the address provided on inputs A0-Ai (where i = 9 for x16; 9 and 11 for x8; or 9, 11, and 12 for x4) selects the starting column location. The value on input A10 determines whether or not auto precharge is used. If auto precharge is selected, the row being accessed will be precharged at the end of the WRITE burst; if auto precharge is not selected, the row will remain open for subsequent accesses. Input data 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 BURST TERMINATE The BURST TERMINATE command is used to truncate READ bursts (with auto precharge disabled). The most recently registered READ command prior to the BURST TERMINATE command will be truncated, as shown in the Operation section of this data sheet. The open page which the READ burst was terminated from remains open. 14 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM AUTO REFRESH AUTO REFRESH is used during normal operation of the DDR SDRAM and is analogous to CAS#-BEFORE-RAS# (CBR) REFRESH in FPM/EDO DRAMs. This command is nonpersistent, so it must be issued each time a refresh is required. The addressing is generated by the internal refresh controller. This makes the address bits a "Don't Care" during an AUTO REFRESH command. The 512Mb DDR SDRAM requires AUTO REFRESH cycles at an average interval of 7.8125s (maximum). To allow for improved efficiency in scheduling and switching between tasks, some flexibility in the absolute refresh interval is provided. A maximum of eight AUTO REFRESH command can be posted to any given DDR SDRAM, meaning that the maximum absolute interval between any AUTO REFRESH command and the next AUTO REFRESH command is 9 x 7.8125s (70.3s). This maximum absolute interval is to allow future support for DLL updates internal to the DDR SDRAM to be restricted to AUTO REFRESH cycles, without allowing excessive drift in tAC between updates. Although not a JEDEC requirement, to provide for future functionality features, CKE must be active (High) 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 during the AUTO REFRESH period. The AUTO REFRESH period begins when the AUTO REFRESH command is registered and ends tRFC latter. SELF REFRESH The SELF REFRESH command can be used to retain data in the DDR SDRAM, even if the rest of the system is powered down. When in the self refresh mode, the DDR SDRAM retains data without external clocking. The SELF REFRESH command is initiated like an AUTO REFRESH command except CKE is disabled (LOW). The DLL is automatically disabled upon entering SELF REFRESH and is automatically enabled upon exiting SELF REFRESH (200 clock cycles must then occur before a READ command can be issued). Input signals except CKE are "Don't Care" during SELF REFRESH. The procedure for exiting self refresh requires a sequence of commands. First, CK must be stable prior to CKE going back HIGH. Once CKE is HIGH, the DDR SDRAM must have NOP commands issued for tXSNR because time is required for the completion of any internal refresh in progress. A simple algorithm for meeting both refresh and DLL requirements is to apply NOPs for 200 clock cycles before applying any other command. 15 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM Operations CK# BANK/ROW ACTIVATION Before any READ or WRITE commands can be issued to a bank within the DDR SDRAM, a row in that bank must be "opened." This is accomplished via the ACTIVE command, which selects both the bank and the row to be activated, as shown in Figure 4. After a row is opened with an ACTIVE command, a READ or WRITE command may be issued to that row, subject to the tRCD specification. tRCD (MIN) should be divided by the clock period and rounded up to the next whole number to determine the earliest clock edge after the ACTIVE command on which a READ or WRITE command can be entered. For example, a tRCD specification of 20ns with a 133 MHz clock (7.5ns period) results in 2.7 clocks rounded to 3. This is reflected in Figure 5, which covers any case where 2 < tRCD (MIN)/tCK 3. (Figure 5 also shows the same case for tRCD; the same procedure is used to convert other specification limits from time units to clock cycles). A subsequent ACTIVE command to a different row in the same bank can only be issued after the previous active row has been "closed" (precharged). The minimum time interval between successive ACTIVE commands to the same bank is defined by tRC. A subsequent ACTIVE command to another bank can be issued while the first bank is being accessed, which results in a reduction of total row-access overhead. The minimum time interval between successive ACTIVE commands to different banks is defined by tRRD. T0 T1 ACT NOP T2 CK CKE HIGH CS# RAS# CAS# WE# A0-A12 RA BA0,1 BA RA = Row Address BA = Bank Address Figure 4 Activating a Specific Row in a Specific Bank T3 T4 T5 T6 T7 NOP NOP RD/WR NOP CK# CK COMMAND A0-A12 BA0, BA1 NOP Row ACT Row Bank x Col Bank y Bank y tRCD tRRD DON'T CARE Figure 5 Example: Meeting tRCD (tRRD) MIN When 2 < tRCD (tRRD) MIN/tCK 3 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 16 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM READs READ bursts are initiated with a READ command, as shown in Figure 6. The starting column and bank addresses are provided with the READ command and auto precharge is either enabled or disabled for that burst access. If auto precharge is enabled, the row being accessed is precharged at the completion of the burst. For the generic READ commands used in the following illustrations, auto precharge is disabled. During READ bursts, the valid data-out element from the starting column address will be available following the CAS latency after the READ command. Each subsequent data-out element will be valid nominally at the next positive or negative clock edge (i.e., at the next crossing of CK and CK#). Figure 7 shows general timing for each possible CAS latency setting. DQS is driven by the DDR SDRAM along with output data. The initial LOW state on DQS is known as the read preamble; the LOW state coincident with the last data-out element is known as the read postamble. Upon completion of a burst, assuming no other commands have been initiated, the DQs will go High-Z. A detailed explanation of tDQSQ (valid dataout skew), tQH (data-out window hold), the valid data window are depicted in Figure 27. A detailed explanation of tDQSCK (DQS transition skew to CK) and tAC (data-out transition skew to CK) is depicted in Figure 28. Data from any READ burst may be concatenated with or truncated with data from a subsequent READ command. In either case, a continuous flow of data can be maintained. The first data element from the new burst follows either the last element of a completed burst or the last desired data element of a longer burst which is being truncated. The new READ command should be issued x cycles after the first READ command, where x equals the number of desired data element pairs (pairs are required by the 2n-prefetch architecture). This is shown in Figure 8. A READ command can be initiated on any clock cycle following a previous READ command. Nonconsecutive read data is shown for illustration in Figure 9. Full-speed random read accesses within a page (or pages) can be performed as shown in Figure 10. 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 CK# CK CKE HIGH CS# RAS# CAS# WE# x4: A0-A9, A11, A12 x8: A0-A9, A11 x16: A0-A9 CA x8: A12 x16: A11, A12 EN AP A10 DIS AP BA0,1 BA CA = Column Address BA = Bank Address EN AP = Enable Auto Precharge DIS AP = Disable Auto Precharge DON'T CARE Figure 6 READ Command 17 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM T0 T1 T2 READ NOP NOP T2n T3 T3n T4 T5 NOP NOP T4 T5 NOP NOP CK# CK COMMAND ADDRESS NOP Bank a, Col n CL = 2 DQS DO n DQ T0 T1 T2 READ NOP NOP T2n T3 T3n CK# CK COMMAND ADDRESS NOP Bank a, Col n CL = 2.5 DQS DO n DQ NOTE: 1. DO n = data-out from column n. DON'T CARE TRANSITIONING DATA 2. Burst length = 4. 3. Three subsequent elements of data-out appear in the programmed order following DO n. 4. Shown with nominal tAC, tDQSCK, and tDQSQ. Figure 7 READ Burst 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 18 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM T0 T1 T2 COMMAND READ NOP READ ADDRESS Bank, Col n T2n T3 T3n T4 T4n T5 T5n CK# CK NOP NOP NOP Bank, Col b CL = 2 DQS DO n DQ T0 T1 T2 COMMAND READ NOP READ ADDRESS Bank, Col n DO b T2n T3 T3n T4 T4n T5 T5n CK# CK NOP NOP NOP Bank, Col b CL = 2.5 DQS DO n DQ DO b DON'T CARE NOTE: 1. 2. 3. 4. 5. 6. TRANSITIONING DATA DO n (or b) = data-out from column n (or column b). Burst length = 4 or 8 (if 4, the bursts are concatenated; if 8, the second burst interrupts the first). Three subsequent elements of data-out appear in the programmed order following DO n. Three (or seven) subsequent elements of data-out appear in the programmed order following DO b. Shown with nominal tAC, tDQSCK, and tDQSQ. Example applies only when READ commands are issued to same device. Figure 8 Consecutive READ Bursts 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 19 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM T0 T1 T2 COMMAND READ NOP NOP ADDRESS Bank, Col n T2n T3 T3n T4 T5 NOP NOP T5n T6 CK# CK READ NOP Bank, Col b CL = 2 DQS DO n DQ T0 T1 T2 COMMAND READ NOP NOP ADDRESS Bank, Col n DO b T2n T3 T3n T4 T5 NOP NOP T5n T6 CK# CK READ NOP Bank, Col b CL = 2.5 DQS DO n DQ NOTE: 1. 2. 3. 4. 5. 6. DO b DON'T CARE TRANSITIONING DATA DO n (or b) = data-out from column n (or column b). Burst length = 4 or 8 (if 4, the bursts are concatenated; if 8, the second burst interrupts the first). Three subsequent elements of data-out appear in the programmed order following DO n. Three (or seven) subsequent elements of data-out appear in the programmed order following DO b. Shown with nominal tAC, tDQSCK, and tDQSQ. Example applies when READ commands are issued to different devices or nonconsecutive READs. Figure 9 Nonconsecutive READ Bursts 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 20 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM T0 T1 T2 T2n T3 T3n T4 COMMAND READ READ READ READ ADDRESS Bank, Col n Bank, Col x Bank, Col b Bank, Col g T4n T5 T5n CK# CK NOP NOP CL = 2 DQS DO n DQ DO n' T2n DO x T0 T1 T2 T3 COMMAND READ READ READ READ ADDRESS Bank, Col n Bank, Col x Bank, Col b Bank, Col g DO x' T3n DO b T4 DO b' T4n DO g T5 T5n CK# CK NOP NOP CL = 2.5 DQS DO n DQ DO n' DO x DON'T CARE NOTE: 1. 2. 3. 4. 5. DO x' DO b DO b' TRANSITIONING DATA DO n (or x or b or g) = data-out from column n (or column x or column b or column g). Burst length = 2 or 4 or 8 (if 4 or 8, the following burst interrupts the previous). n' or x' or b' or g' indicates the next data-out following DO n or DO x or DO b or DO g, respectively. READs are to an active row in any bank. Shown with nominal tAC, tDQSCK, and tDQSQ. Figure 10 Random READ Accesses 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 21 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM READs (continued) Data from any READ burst may be truncated with a BURST TERMINATE command, as shown in Figure 11. The BURST TERMINATE latency is equal to the READ (CAS) latency, i.e., the BURST TERMINATE command should be issued x cycles after the READ command, where x equals the number of desired data element pairs (pairs are required by the 2n-prefetch architecture). Data from any READ burst must be completed or truncated before a subsequent WRITE command can be issued. If truncation is necessary, the BURST TERMINATE command must be used, as shown in Figure 12. The tDQSS (MIN) case is shown; the tDQSS (MAX) case has a longer bus idle time. (tDQSS [MIN] and tDQSS [MAX] are defined in the section on WRITEs.) 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 A READ burst may be followed by, or truncated with, a PRECHARGE command to the same bank provided that auto precharge was not activated. The PRECHARGE command should be issued x cycles after the READ command, where x equals the number of desired data element pairs (pairs are required by the 2nprefetch architecture). This is shown in Figure 13. Following the PRECHARGE command, a subsequent command to the same bank cannot be issued until tRP is met. Note that part of the row precharge time is hidden during the access of the last data elements. 22 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM T0 T1 T2 T2n READ BST5 NOP T3 T4 T5 NOP NOP NOP T3 T4 T5 NOP NOP NOP CK# CK COMMAND ADDRESS Bank a, Col n CL = 2 DQS DO n DQ T0 T1 T2 T2n READ BST5 NOP CK# CK COMMAND ADDRESS Bank a, Col n CL = 2.5 DQS DO n DQ NOTE: 1. 2. 3. 4. 5. DO n = data-out from column n. DON'T CARE TRANSITIONING DATA Burst length = 4. Subsequent element of data-out appears in the programmed order following DO n. Shown with nominal tAC, tDQSCK, and tDQSQ. BST = BURST TERMINATE command, page remains open. Figure 11 Terminating a READ Burst 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 23 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM T0 T1 T2 T2n COMMAND READ BST7 NOP ADDRESS Bank, Col n T3 T4 T4n T5 T5n CK# CK WRITE NOP NOP T4 T5 Bank, Col b tDQSS (MIN) CL = 2 DQS DO n DQ DI b DM T0 T1 T2 T2n READ BST7 NOP T3 T5n CK# CK COMMAND ADDRESS NOP WRITE NOP Bank a, Col n tDQSS (MIN) CL = 2.5 DQS DO n DQ DI b DM NOTE: 1. DO n = data-out from column n. DON'T CARE TRANSITIONING DATA 2. DI b = data-in from column b. 3. Burst length = 4 in the cases shown (applies for bursts of 8 as well; if the burst length is 2, the BST command shown can be NOP). 4. One subsequent element of data-out appears in the programmed order following DO n. 5. Data-in elements are applied following DI b in the programmed order. 6. Shown with nominal tAC, tDQSCK, and tDQSQ. 7. BST = BURST TERMINATE command, page remains open. Figure 12 READ to WRITE 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 24 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM T0 T1 T2 T2n READ NOP PRE T3 T3n T4 T5 NOP ACT CK# CK COMMAND6 ADDRESS Bank a, Col n NOP Bank a, (a or all) Bank a, Row tRP CL = 2 DQS DO n DQ T0 T1 T2 READ NOP PRE T2n T3 T3n T4 T5 NOP ACT CK# CK COMMAND6 ADDRESS NOP Bank a, (a or all) Bank a, Col n Bank a, Row tRP CL = 2.5 DQS DO n DQ NOTE: 1. 2. 3. 4. 5. 6. DO n = data-out from column n. DON'T CARE TRANSITIONING DATA Burst length = 4, or an interrupted burst of 8. Three subsequent elements of data-out appear in the programmed order following DO n. Shown with nominal tAC, tDQSCK, and tDQSQ. READ to PRECHARGE equals two clocks, which allows two data pairs of data-out. PRE = PRECHARGE command; ACT = ACTIVE command. Figure 13 READ to PRECHARGE 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 25 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM WRITEs WRITE bursts are initiated with a WRITE command, as shown in Figure 14. The starting column and bank addresses are provided with the WRITE command, and auto precharge is either enabled or disabled for that access. If auto precharge is enabled, the row being accessed is precharged at the completion of the burst. For the generic WRITE commands used in the following illustrations, auto precharge is disabled. During WRITE bursts, the first valid data-in element will be registered on the first rising edge of DQS following the WRITE command, and subsequent data elements will be registered on successive edges of DQS. The LOW state on DQS between the WRITE command and the first rising edge is known as the write preamble; the LOW state on DQS following the last data-in element is known as the write postamble. The time between the WRITE command and the first corresponding rising edge of DQS (tDQSS) is specified with a relatively wide range (from 75 percent to 125 percent of one clock cycle). All of the WRITE diagrams show the nominal case, and where the two extreme cases (i.e., tDQSS [MIN] and tDQSS [MAX]) might not be intuitive, they have also been included. Figure 15 shows the nominal case and the extremes of tDQSS for a burst of 4. Upon completion of a burst, assuming no other commands have been initiated, the DQs will remain High-Z and any additional input data will be ignored. Data for any WRITE burst may be concatenated with or truncated with a subsequent WRITE command. In either case, a continuous flow of input data can be maintained. The new WRITE command can be issued on any positive edge of clock following the previous WRITE command. The first data element from the new burst is applied after either the last element of a completed burst or the last desired data element of a longer burst which is being truncated. The new WRITE command should be issued x cycles after the first WRITE command, where x equals the number of desired data element pairs (pairs are required by the 2n-prefetch architecture). Figure 16 shows concatenated bursts of 4. An example of nonconsecutive WRITEs is shown in Figure 17. Full-speed random write accesses within a page or pages can be performed as shown in Figure 18. Data for any WRITE burst may be followed by a subsequent READ command. To follow a WRITE without truncating the WRITE burst, tWTR should be met as shown in Figure 19. Data for any WRITE burst may be truncated by a subsequent READ command, as shown in Figure 20. Note that only the data-in pairs that are registered 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 CK# CK CKE HIGH CS# RAS# CAS# WE# x4: A0-A9, A11, A12 x8: A0-A9, A11 x16: A0-A9 CA x8: A12 x16:A11, A12 EN AP A10 DIS AP BA0,1 BA CA = Column Address BA = Bank Address EN AP = Enable Auto Precharge DIS AP = Disable Auto Precharge DON'T CARE Figure 14 WRITE Command prior to the tWTR period are written to the internal array, and any subsequent data-in should be masked with DM as shown in Figure 21. Data for any WRITE burst may be followed by a subsequent PRECHARGE command. To follow a WRITE without truncating the WRITE burst, tWR should be met as shown in Figure 22. Data for any WRITE burst may be truncated by a subsequent PRECHARGE command, as shown in Figures 23 and 24. Note that only the data-in pairs that are registered prior to the tWR period are written to the internal array, and any subsequent data-in should be masked with DM as shown in Figures 23 and 24. After the PRECHARGE command, a subsequent command to the same bank cannot be issued until tRP is met. 26 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM T0 T1 T2 COMMAND WRITE NOP NOP ADDRESS Bank a, Col b T2n T3 CK# CK NOP tDQSS (NOM) DQS tDQSS DI b DQ DM tDQSS (MIN) DQS DQ tDQSS DI b DM tDQSS (MAX) DQS DQ tDQSS DI b DM DON'T CARE TRANSITIONING DATA NOTE: 1. DI b = data-in for column b. 2. Three subsequent elements of data-in are applied in the programmed order following DI b. 3. An uninterrupted burst of 4 is shown. 4. A10 is LOW with the WRITE command (auto precharge is disabled). Figure 15 WRITE Burst 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 27 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM T0 T1 COMMAND WRITE NOP ADDRESS Bank, Col b T1n T2 T2n T3 T3n T4 T4n T5 CK# CK tDQSS (NOM) WRITE NOP NOP NOP Bank, Col n tDQSS DQS DI b DQ DI n DM DON'T CARE NOTE: 1. 2. 3. 4. 5. TRANSITIONING DATA DI b, etc. = data-in for column b, etc. Three subsequent elements of data-in are applied in the programmed order following DI b. Three subsequent elements of data-in are applied in the programmed order following DI n. An uninterrupted burst of 4 is shown. Each WRITE command may be to any bank. Figure 16 Consecutive WRITE to WRITE 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 28 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM T0 T1 COMMAND WRITE NOP ADDRESS Bank, Col b T1n T2 T2n T3 T4 T4n T5 T5n CK# CK tDQSS (NOM) NOP WRITE NOP NOP Bank, Col n tDQSS DQS DI n DI b DQ DM DON'T CARE NOTE: 1. 2. 3. 4. 5. TRANSITIONING DATA DI b, etc. = data-in for column b, etc. Three subsequent elements of data-in are applied in the programmed order following DI b. Three subsequent elements of data-in are applied in the programmed order following DI n. An uninterrupted burst of 4 is shown. Each WRITE command may be to any bank. FIGURE 17 Nonconsecutive WRITE to WRITE 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 29 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM T0 T1 T1n T2 T2n T3 T3n T4 COMMAND WRITE WRITE WRITE WRITE WRITE ADDRESS Bank, Col b Bank, Col x Bank, Col n Bank, Col a Bank, Col g T4n T5 T5n CK# CK NOP tDQSS (NOM) DQS DI b DQ DI b' DI x DI x' DI n DI n' DI a DI a' DI g DI g' DM DON'T CARE NOTE: 1. 2. 3. 4. TRANSITIONING DATA DI b, etc. = data-in for column b, etc. b', etc. = the next data-in following DI b, etc., according to the programmed burst order. Programmed burst length = 2, 4, or 8 in cases shown. Each WRITE command may be to any bank. Figure 18 Random WRITE Cycles 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 30 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM T0 T1 WRITE NOP T1n T2 T2n T3 T4 T5 T6 NOP READ NOP NOP T6n CK# CK COMMAND NOP tWTR Bank a, Col b ADDRESS tDQSS (NOM) Bank a, Col n tDQSS CL = 2 DQS DI b DQ DI n DM tDQSS (MIN) tDQSS CL = 2 DQS DI b DQ DI n DM tDQSS (MAX) tDQSS CL = 2 DQS DI b DQ DI n DM DON'T CARE TRANSITIONING DATA DI b = data-in for column b. Three subsequent elements of data-in are applied in the programmed order following DI b. An uninterrupted burst of 4 is shown. tWTR is referenced from the first positive CK edge after the last data-in pair. The READ and WRITE commands are to the same bank. However, the READ and WRITE commands may be to different devices, in which case tWTR is not required and the READ command could be applied earlier. 6. A10 is LOW with the WRITE command (auto precharge is disabled). NOTE: 1. 2. 3. 4. 5. Figure 19 WRITE to READ - Uninterrupting 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 31 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM T0 T1 WRITE NOP T1n T2 T2n T3 T4 T5 READ NOP NOP T5n T6 T6n CK# CK COMMAND NOP NOP tWTR Bank a, Col b ADDRESS tDQSS (NOM) Bank a, Col n tDQSS CL = 2 DQS DI b DQ DI n DM tDQSS (MIN) tDQSS CL = 2 DQS DI b DQ DI n DM tDQSS (MAX) tDQSS CL = 2 DQS DI b DQ DI n DM NOTE: 1. 2. 3. 4. 5. 6. 7. DON'T CARE TRANSITIONING DATA DI b = data-in for column b. An interrupted burst of 4 or 8 is shown; two data elements are written. One subsequent element of data-in is applied in the programmed order following DI b. tWTR is referenced from the first positive CK edge after the last data-in pair. A10 is LOW with the WRITE command (auto precharge is disabled). DQS is required at T2 and T2n (nominal case) to register DM. If the burst of 8 was used, DM would not be required at T3 -T4n because the READ command would mask the last two data elements. Figure 20 WRITE to READ - Interrupting 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 32 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM T0 T1 WRITE NOP T1n T2 T2n T3 T4 T5 READ NOP NOP T5n T6 T6n CK# CK COMMAND NOP NOP tWTR Bank a, Col b ADDRESS tDQSS (NOM) Bank a, Col n tDQSS CL = 2 DQS DI b DQ DI n DM tDQSS (MIN) tDQSS CL = 2 DQS DI b DQ DI n DM tDQSS (MAX) tDQSS CL = 2 DQS DI b DQ DI n DM NOTE: 1. 2. 3. 4. 5. 6. DON'T CARE TRANSITIONING DATA DI b = data-in for column b. An interrupted burst of 4 is shown; one data element is written. tWTR is referenced from the first positive CK edge after the last desired data-in pair (not the last two data elements). A10 is LOW with the WRITE command (auto precharge is disabled). DQS is required at T1n, T2, and T2n (nominal case) to register DM. If the burst of 8 was used, DM would not be required at T3 -T4n because the READ command would mask the last four data elements. Figure 21 WRITE to READ - Odd Number of Data, Interrupting 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 33 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM T0 T1 WRITE NOP T1n T2 T2n T3 T4 T5 NOP PRE7 T6 CK# CK COMMAND NOP NOP tWR ADDRESS tDQSS (NOM) Bank a, Col b NOP tRP Bank, (a or all) tDQSS DQS DQ DI b DM tDQSS (MIN) tDQSS DQS DI b DQ DM tDQSS (MAX) tDQSS DQS DQ DI b DM DON'T CARE TRANSITIONING DATA DI b = data-in for column b. Three subsequent elements of data-in are applied in the programmed order following DI b. An uninterrupted burst of 4 is shown. tWR is referenced from the first positive CK edge after the last data-in pair. The PRECHARGE and WRITE commands are to the same bank. However, the PRECHARGE and WRITE commands may be to different devices, in which case tWR is not required and the PRECHARGE command could be applied earlier. 6. A10 is LOW with the WRITE command (auto precharge is disabled). 7. PRE = PRECHARGE command. NOTE: 1. 2. 3. 4. 5. Figure 22 WRITE to PRECHARGE - Uninterrupting 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 34 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM T0 T1 WRITE NOP T1n T2 T2n T3 T4 T5 NOP PRE9 NOP T6 CK# CK COMMAND NOP tWR ADDRESS tDQSS (NOM) Bank a, Col b NOP tRP Bank, (a or all) tDQSS DQS DI b DQ DM tDQSS (MIN) tDQSS DQS DI b DQ DM tDQSS (MAX) tDQSS DQS DQ DI b DM DON'T CARE TRANSITIONING DATA DI b = data-in for column b. Subsequent element of data-in is applied in the programmed order following DI b. An interrupted burst of 4 is shown; two data elements are written. tWR is referenced from the first positive CK edge after the last data-in pair. The PRECHARGE and WRITE commands are to the same bank. A10 is LOW with the WRITE command (auto precharge is disabled). DQS is required at T2 and T2n (nominal case) to register DM. If the burst of 8 was used, DM would be required at T3 and T3n and not at T4 and T4n because the PRECHARGE command would mask the last two data elements. 9. PRE = PRECHARGE command. NOTE: 1. 2. 3. 4. 5. 6. 7. 8. Figure 23 WRITE to Precharge - Interrupting 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 35 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM T0 T1 WRITE NOP T1n T2 T2n T3 T4 T5 NOP PRE9 NOP T6 CK# CK COMMAND NOP tWR ADDRESS tDQSS (NOM) Bank a, Col b NOP tRP Bank, (a or all) tDQSS DQS DI b DQ DM tDQSS (MIN) tDQSS DQS DI b DQ DM tDQSS (MAX) tDQSS DQS DQ DI b DM DON'T CARE TRANSITIONING DATA NOTE: 1. 2. 3. 4. 5. 6. 7. 8. DI b = data-in for column b. Subsequent element of data-in is applied in the programmed order following DI b. An interrupted burst of 4 is shown; one data element is written. tWR is referenced from the first positive CK edge after the last data-in pair. The PRECHARGE and WRITE commands are to the same bank. A10 is LOW with the WRITE command (auto precharge is disabled). DQS is required at T1n, T2 and T2n (nominal case) to register DM. If the burst of 8 was used, DM would be required at T3 and T3n and not at T4 and T4n because the PRECHARGE command would mask the last two data elements. 9. PRE = PRECHARGE command. Figure 24 WRITE to PRECHARGE Odd Number of Data, Interrupting 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 36 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM PRECHARGE The PRECHARGE command (Figure 25) is used to deactivate the open row in a particular bank or the open row in all banks. The bank(s) will be available for a subsequent row access some specified time (tRP) after the PRECHARGE command is issued. Input A10 deter- mines whether one or all banks are to be precharged, and in the case where only one bank is to be precharged, inputs BA0, BA1 select the bank. When all banks are to be precharged, inputs BA0, BA1 are treated as "Don't Care." Once a bank has been precharged, it is in the idle state and must be activated prior to any READ or WRITE commands being issued to that bank. CK# POWER-DOWN (CKE NOT ACTIVE) Unlike SDR SDRAMs, DDR SDRAMs require CKE to be active at all times an access is in progress: from the issuing of a READ or WRITE command until completion of the burst. Thus a clock suspend is not supported. For READs, a burst completion is defined when the Read Postamble is satisfied; For WRITEs, a burst completion is defined when the Write Postamble is satisfied. Power-down (Figure 26) is entered when CKE is registered LOW. If power-down occurs when all banks are idle, this mode is referred to as precharge powerdown; if power-down occurs when there is a row active in any bank, this mode is referred to as active powerdown. Entering power-down deactivates the input and output buffers, excluding CK, CK#, and CKE. For maximum power savings, the DLL is frozen. Exiting power-down requires the device to be at the same. voltage and frequency as when it entered power-down. However, power-down duration is limited by the refresh requirements of the device (tREFC). While in power-down, CKE LOW and a stable clock signal must be maintained at the inputs of the DDR SDRAM, while all other input signals are "Don't Care." The power-down state is synchronously exited when CKE is registered HIGH (in conjunction with a NOP or DESELECT command). A valid executable command may be applied one clock cycle later. CK CKE HIGH CS# RAS# CAS# WE# A0-A9, A11, A12 ALL BANKS A10 ONE BANK BA0,1 BA BA = Bank Address (if A10 is LOW; otherwise "Don't Care") DON'T CARE Figure 25 PRECHARGE Command T0 T1 CK# T2 ( ( Ta0 CK Ta2 tIS tIS CKE COMMAND Ta1 )) (( )) (( )) VALID No READ/WRITE access in progress NOP (( )) (( )) Enter power-down mode NOP VALID Exit power-down mode DON'T CARE Figure 26 Power-Down 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 37 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM TRUTH TABLE 2 - CKE (Notes: 1-4) CKEn-1 CKEn L L H H NOTE: 1. 2. 3. 4. 5. L H L CURRENT STATE COMMAND n Power-Down X Maintain Power-Down Self Refresh X Maintain Self Refresh Power-Down DESELECT or NOP Exit Power-Down Self Refresh DESELECT or NOP Exit Self Refresh All Banks Idle DESELECT or NOP Precharge Power-Down Entry Bank(s) Active DESELECT or NOP Active Power-Down Entry All Banks Idle AUTO REFRESH H ACTION n NOTES 5 Self Refresh Entry See Truth Table 3 CKEn is the logic state of CKE at clock edge n; CKEn-1 was the state of CKE at the previous clock edge. Current state is the state of the DDR SDRAM immediately prior to clock edge n. COMMANDn is the command registered at clock edge n, and ACTIONn is a result of COMMANDn. All states and sequences not shown are illegal or reserved. DESELECT or NOP commands should be issued on any clock edges occurring during the tXSR period. A minimum of 200 clock cycles is needed before applying a READ command for the DLL to lock. 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 38 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM TRUTH TABLE 3 - CURRENT STATE BANK n - COMMAND TO BANK n (Notes: 1-6; notes appear below and on next page) CURRENT STATE CS# RAS# CAS# WE# Any Idle Row Active COMMAND/ACTION NOTES H X X X DESELECT (NOP/continue previous operation) L H H H NO OPERATION (NOP/continue previous operation) L L H H ACTIVE (select and activate row) L L L H AUTO REFRESH 7 L L L L LOAD MODE REGISTER 7 L H L H READ (select column and start READ burst) 10 L H L L WRITE (select column and start WRITE burst) 10 L L H L PRECHARGE (deactivate row in bank or banks) 8 Read L H L H READ (select column and start new READ burst) (Auto- L H L L WRITE (select column and start WRITE burst) Precharge L L H L PRECHARGE (truncate READ burst, start PRECHARGE) 8 Disabled) L H H L BURST TERMINATE 9 Write L H L H READ (select column and start READ burst) (Auto- L H L L WRITE (select column and start new WRITE burst) Precharge L L H L PRECHARGE (truncate WRITE burst, start PRECHARGE) 10 10, 12 10, 11 10 8, 11 Disabled) NOTE: 1. This table applies when CKEn-1 was HIGH and CKEn is HIGH (see Truth Table 2) and after tXSNR has been met (if the previous state was self refresh). 2. This table is bank-specific, except where noted (i.e., the current state is for a specific bank and the commands shown are those allowed to be issued to that bank when in that state). Exceptions are covered in the notes below. 3. Current state definitions: Idle: The bank has been precharged, and tRP has been met. Row Active: A row in the bank has been activated, and tRCD has been met. No data bursts/accesses and no register accesses are in progress. Read: A READ burst has been initiated, with auto precharge disabled, and has not yet terminated or been terminated. Write: A WRITE burst has been initiated, with auto precharge disabled, and has not yet terminated or been terminated. 4. The following states must not be interrupted by a command issued to the same bank. COMMAND INHIBIT or NOP commands, or allowable commands to the other bank should be issued on any clock edge occurring during these states. Allowable commands to the other bank are determined by its current state and Truth Table 3, and according to Truth Table 4. Precharging: Starts with registration of a PRECHARGE command and ends when tRP is met. Once tRP is met, the bank will be in the idle state. Row Activating: Starts with registration of an ACTIVE command and ends when tRCD is met. Once tRCD is met, the bank will be in the "row active" state. Read w/AutoPrecharge Enabled: Starts with registration of a READ command with auto precharge enabled and ends when tRP has been met. Once tRP is met, the bank will be in the idle state. Write w/AutoPrecharge Enabled: Starts with registration of a WRITE command with auto precharge enabled and ends when tRP has been met. Once tRP is met, the bank will be in the idle state. 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 39 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM NOTE (continued): 5. The following states must not be interrupted by any executable command; COMMAND INHIBIT or NOP commands must be applied on each positive clock edge during these states. Refreshing: Starts with registration of an AUTO REFRESH command and ends when tRC is met. Once tRC is met, the DDR SDRAM will be in the all banks idle state. Accessing Mode Register: Starts with registration of a LOAD MODE REGISTER command and ends when tMRD has been met. Once tMRD is met, the DDR SDRAM will be in the all banks idle state. Precharging All: Starts with registration of a PRECHARGE ALL command and ends when tRP is met. Once tRP is met, all banks will be in the idle state. 6. All states and sequences not shown are illegal or reserved. 7. Not bank-specific; requires that all banks are idle, and bursts are not in progress. 8. May or may not be bank-specific; if multiple banks are to be precharged, each must be in a valid state for precharging. 9. Not bank-specific; BURST TERMINATE affects the most recent READ burst, regardless of bank. 10. READs or WRITEs listed in the Command/Action column include READs or WRITEs with auto precharge enabled and READs or WRITEs with auto precharge disabled. 11. Requires appropriate DM masking. 12. A WRITE command may be applied after the completion of the READ burst; otherwise, a BURST TERMINATE must be used to end the READ burst prior to asserting a WRITE command. 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 40 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM TRUTH TABLE 4 - CURRENT STATE BANK n - COMMAND TO BANK m (Notes: 1-6; notes appear below and on next page) CURRENT STATE Any CS# RAS# CAS# WE# COMMAND/ACTION NOTES H X X X DESELECT (NOP/continue previous operation) L H H H NO OPERATION (NOP/continue previous operation) Idle X X X X Any Command Otherwise Allowed to Bank m Row L L H H ACTIVE (select and activate row) Activating, L H L H READ (select column and start READ burst) 7 Active, or L H L L WRITE (select column and start WRITE burst) 7 Precharging L L H L PRECHARGE Read L L H H ACTIVE (select and activate row) (Auto- L H L H READ (select column and start new READ burst) Precharge L H L L WRITE (select column and start WRITE burst) Disabled) L L H L PRECHARGE Write L L H H ACTIVE (select and activate row) 7 7, 9 (Auto- L H L H READ (select column and start READ burst) Precharge L H L L WRITE (select column and start new WRITE burst) 7, 8 Disabled) L L H L PRECHARGE Read L L H H ACTIVE (select and activate row) (With Auto- L H L H READ (select column and start new READ burst) Precharge) L H L L WRITE (select column and start WRITE burst) L L H L PRECHARGE Write L L H H ACTIVE (select and activate row) (With Auto- L H L H READ (select column and start READ burst) 7, 3a Precharge) L H L L WRITE (select column and start new WRITE burst) 7, 3a L L H L PRECHARGE 7 7, 3a 7, 9, 3a NOTE: 1. This table applies when CKEn-1 was HIGH and CKEn is HIGH (see Truth Table 2) and after tXSNR has been met (if the previous state was self refresh). 2. This table describes alternate bank operation, except where noted (i.e., the current state is for bank n and the commands shown are those allowed to be issued to bank m, assuming that bank m is in such a state that the given command is allowable). Exceptions are covered in the notes below. (Notes continued on next page) 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 41 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM NOTE (continued): 3.Current state definitions: Idle: The bank has been precharged, and tRP has been met. Row Active: A row in the bank has been activated, and tRCD has been met. No data bursts/accesses and no register accesses are in progress. Read: A READ burst has been initiated, with auto precharge disabled, and has not yet terminated or been terminated. Write: A WRITE burst has been initiated, with auto precharge disabled, and has not yet terminated or been terminated. Read with Auto Precharge Enabled: See following text - 3a Write with Auto Precharge Enabled: See following text - 3a 3a. The read with auto precharge enabled or write with auto precharge enabled states can each be broken into two parts: the access period and the precharge period. For read with auto precharge, the precharge period is defined as if the same burst was executed with auto precharge disabled and then followed with the earliest possible PRECHARGE command that still accesses all of the data in the burst. For write with auto precharge, the precharge period begins when tWR ends, with tWR measured as if auto precharge was disabled. The access period starts with registration of the command and ends where the precharge period (or tRP) begins. During the precharge period of the read with auto precharge enabled or write with auto precharge enabled states, ACTIVE, PRECHARGE, READ and WRITE commands to the other bank may be applied; during the access period, only ACTIVE and PRECHARGE commands to the other bank may be applied. In either case, all other related limitations apply (e.g., contention between read data and write data must be avoided). This means concurrent auto precharge is not supported. 4. AUTO REFRESH and LOAD MODE REGISTER commands may only be issued when all banks are idle. 5. A BURST TERMINATE command cannot be issued to another bank; it applies to the bank represented by the current state only. 6. All states and sequences not shown are illegal or reserved. 7. READs or WRITEs listed in the Command/Action column include READs or WRITEs with auto precharge enabled and READs or WRITEs with auto precharge disabled. 8. Requires appropriate DM masking. 9. A WRITE command may be applied after the completion of the READ burst; otherwise, a BURST TERMINATE must be used to end the READ burst prior to asserting a WRITE command. 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 42 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM ABSOLUTE MAXIMUM RATINGS* *Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. VDD Supply Voltage Relative to VSS ........ -1V to +3.6V VDDQ Supply Voltage Relative to VSS ..... -1V to +3.6V VREF and Inputs Voltage Relative to VSS ... -1V to +3.6V I/O Pins Voltage Relative to VSS .. -0.5V to VDDQ +0.5V Operating Temperature, TA (ambient) .. 0C to +70C Storage Temperature (plastic) ........... -55C to +150C Power Dissipation ................................................... 1W Short Circuit Output Current ............................ 50mA DC ELECTRICAL CHARACTERISTICS AND OPERATING CONDITIONS (Notes: 1-5, 16; notes appear on pages 50-53) (0C TA +70C; VDD = +2.5V 0.2V, VDDQ = +2.5V 0.2V) PARAMETER/CONDITION Supply Voltage I/O Supply Voltage SYMBOL MIN MAX VDD 2.3 2.7 UNITS NOTES V 41 VDDQ 2.3 2.7 V 41, 44 V 6, 44 V 7, 44 I/O Reference Voltage VREF I/O Termination Voltage (system) VTT VREF - 0.04 Input High (Logic 1) Voltage VIH(DC) VREF + 0.15 VDD + 0.3 V 28 Input Low (Logic 0) Voltage VIL(DC) -0.3 VREF - 0.15 V 28 Clock Input Voltage Level; CK and CK# VIN -0.3 VDDQ + 0.3 V Clock Input Differential Voltage; CK and CK# VID 0.36 VDDQ + 0.6 V 8 Clock Input Crossing Point Voltage; CK and CK# VIX 1.15 1.35 V 9 II -2 2 A IOZ -5 5 A OUTPUT LEVELS: Full drive option - x4, x8, x16 High Current (VOUT = VDDQ-0.373V, minimum VREF, minimum VTT) Low Current (VOUT = 0.373V, maximum VREF, maximum VTT) IOH IOL -16.8 16.8 - - mA mA 37, 39 OUTPUT LEVELS: Reduced drive option - x16 only High Current (VOUT = VDDQ-0.763V, minimum VREF, minimum VTT) Low Current (VOUT = 0.763V, maximum VREF, maximum VTT) IOHR IOLR -9 9 - - mA mA 38, 39 INPUT LEAKAGE CURRENT Any input 0V VIN VDD, VREF pin 0V VIN 1.35V (All other pins not under test = 0V) OUTPUT LEAKAGE CURRENT (DQs are disabled; 0V VOUT VDDQ) 0.49 x VDDQ 0.51 x VDDQ VREF + 0.04 AC INPUT OPERATING CONDITIONS (Notes: 1-5, 14, 16; notes appear on pages 50-53) (0C TA +70C; VDD = +2.5V 0.2V, VDDQ = +2.5V 0.2V) PARAMETER/CONDITION SYMBOL MIN Input High (Logic 1) Voltage VIH(AC) Input Low (Logic 0) Voltage VIL(AC) Clock Input Differential Voltage; CK and CK# VID(AC) Clock Input Crossing Point Voltage; CK and CK# VIX(AC) I/O Reference Voltage VREF(AC) 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 43 MAX UNITS NOTES VREF + 0.310 - V 14, 28, 40 - VREF - 0.310 V 14, 28, 40 0.7 VDDQ + 0.6 V 8 V 9 V 6 0.5 x VDDQ - 0.2 0.5 x VDDQ + 0.2 0.49 x VDDQ 0.51 x VDDQ Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM CAPACITANCE (x4, x8) (Note: 13; notes appear on pages 50-53) PARAMETER SYMBOL MIN MAX UNITS NOTES Delta Input/Output Capacitance: DQs, DQS, DM DCIO - 0.50 pF 24 Delta Input Capacitance: Command and Address DCI1 - 0.50 pF 29 Delta Input Capacitance: CK, CK# DCI2 - 0.25 pF 29 Input/Output Capacitance: DQs, DQS, DM CIO 4.0 5.0 pF Input Capacitance: Command and Address CI1 2.0 3.0 pF Input Capacitance: CK, CK# CI2 2.0 3.0 pF Input Capacitance: CKE CI3 2.0 3.0 pF 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 44 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM IDD SPECIFICATIONS AND CONDITIONS (x4, x8) (Notes: 1-5, 10, 12, 14; notes appear on pages 50-53) (0C TA +70C; VDDQ = +2.5V 0.2V, VDD = +2.5V 0.2V) MAX PARAMETER/CONDITION SYMBOL -7 -75 -8 UNITS NOTES OPERATING CURRENT: One bank; Active-Precharge; tRC = tRC(MIN); tCK = tCK(MIN); DQ, DM, and DQS inputs changing once per clock cyle; Address and control inputs changing once every two clock cycles; IDD0 TBD TBD TBD mA 22, 48 OPERATING CURRENT: One bank; Active-Read-Precharge; Burst = 2; tRC = tRC(MIN); tCK = tCK(MIN); IOUT = 0mA; Address and control inputs changing once per clock cycle IDD1 TBD TBD TBD mA 22, 48 PRECHARGE POWER-DOWN STANDBY CURRENT: All banks idle; Power-down mode; tCK = tCK(MIN); CKE = LOW; IDD2P 3 3 3 mA 23, 32 50 IDLE STANDBY CURRENT: CS# = HIGH; All banks idle; tCK = tCK(MIN); CKE = HIGH; Address and other control inputs changing once per clock cycle. VIN = VREF for DQ, DQS, and DM IDD2F 35 35 30 mA 51 ACTIVE POWER-DOWN STANDBY CURRENT: One bank active; Power-down mode; tCK = tCK(MIN); CKE = LOW IDD3P 3 3 3 mA 50 23, 32 ACTIVE STANDBY CURRENT: CS# = HIGH; CKE = HIGH; One bank; Active-Precharge; tRC = tRAS(MAX); tCK = tCK(MIN); DQ, DM, and DQS inputs changing twice per clock cycle; Address and other control inputs changing once per clock cycle IDD3N 35 35 30 mA 22 OPERATING CURRENT: Burst = 2; Reads; Continuous burst; One bank active; Address and control inputs changing once per clock cycle; tCK = tCK(MIN); IOUT = 0mA IDD4R TBD TBD TBD mA 22, 48 OPERATING CURRENT: Burst = 2; Writes; Continuous burst; One bank active; Address and control inputs changing once per clock cycle; tCK = tCK(MIN); DQ, DM, and DQS inputs changing twice per clock cycle IDD4W TBD TBD TBD mA 22 tRC = tRFC(MIN) IDD5 TBD TBD TBD mA 22,50 tRC = 7.8125s IDD6 6 6 6 mA 27,50 Standard Low power (L) IDD7 IDD7 TBD TBD TBD TBD TBD TBD mA mA 11 11 OPERATING CURRENT: Four bank interleaving READs (BL=4) with auto precharge, tRC = tRC(MIN); tCK = tRC(MIN); Address and control inputs change only during Active READ, or WRITE commands. IDD8 TBD TBD TBD mA 22, 49 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. AUTO REFRESH CURRENT SELF REFRESH CURRENT: CKE 0.2V 45 ADVANCE 512Mb: x4, x8, x16 DDR SDRAM CAPACITANCE (x16) (Note: 13; notes appear on pages 50-53) PARAMETER SYMBOL MIN MAX UNITS NOTES Delta Input/Output Capacitance: DQ0-DQ7, LDQS, LDM DCIOL - 0.50 pF 24 Delta Input/Output Capacitance: DQ8-DQ15, UDQS, UDM DCIOU - 0.50 pF 24 Delta Input Capacitance: Command and Address DCI1 - 0.50 pF 29 Delta Input Capacitance: CK, CK# DCI2 - 0.25 pF 29 Input/Output Capacitance: DQs, LDQS, UDQS, LDM, UDM CIO 4.0 5.0 pF Input Capacitance: Command and Address CI1 2.0 3.0 pF Input Capacitance: CK, CK# CI2 2.0 3.0 pF Input Capacitance: CKE CI3 2.0 3.0 pF 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 46 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM IDD SPECIFICATIONS AND CONDITIONS (x16) (Notes: 1-5, 10, 12, 14; notes appear on pages 50-53) (0C TA +70C; VDDQ = +2.5V 0.2V, VDD = +2.5V 0.2V) MAX PARAMETER/CONDITION SYMBOL -7 -75 -8 UNITS NOTES OPERATING CURRENT: One bank; Active-Precharge; = tCK = tCK(MIN); DQ, DM, and DQS inputs changing once per clock cyle; Address and control inputs changing once every two clock cycles; IDD0 TBD TBD TBD mA 22, 48 OPERATING CURRENT: One bank; Active-Read-Precharge; Burst = 2; tRC = tRC(MIN); tCK = tCK(MIN); IOUT = 0mA; Address and control inputs changing once per clock cycle IDD1 TBD TBD TBD mA 22, 48 PRECHARGE POWER-DOWN STANDBY CURRENT: All banks idle; Power-down mode; tCK = tCK(MIN); CKE = LOW; IDD2P 3 3 3 mA 23, 32 50 IDLE STANDBY CURRENT: CS# = HIGH; All banks idle; tCK = tCK(MIN); CKE = HIGH; Address and other control inputs changing once per clock cycle. VIN = VREF for DQ, DQS, and DM IDD2F 40 40 35 mA 51 ACTIVE POWER-DOWN STANDBY CURRENT: One bank active; Power-down mode; tCK = tCK(MIN); CKE = LOW IDD3P 3 3 3 mA 50 23, 32 ACTIVE STANDBY CURRENT: CS# = HIGH; CKE = HIGH; One bank; Active-Precharge; tRC = tRAS(MAX); tCK = tCK(MIN); DQ, DM, and DQS inputs changing twice per clock cycle; Address and other control inputs changing once per clock cycle IDD3N 35 35 30 mA 22 OPERATING CURRENT: Burst = 2; Reads; Continuous burst; One bank active; Address and control inputs changing once per clock cycle; tCK = tCK(MIN); IOUT = 0mA IDD4R TBD TBD TBD mA 22, 48 OPERATING CURRENT: Burst = 2; Writes; Continuous burst; One bank active; Address and control inputs changing once per clock cycle; tCK = tCK(MIN); DQ, DM, and DQS inputs changing twice per clock cycle IDD4W TBD TBD TBD mA 22 tRC tRC(MIN); tRC = tRFC(MIN) IDD5 TBD TBD TBD mA 22,50 tRC = 7.8125s IDD6 6 6 6 mA 27,50 Standard Low power (L) IDD7 IDD7 TBD TBD TBD TBD TBD TBD mA mA 11 11 OPERATING CURRENT: Four bank interleaving READs (BL=4) with auto precharge with , tRC = tRC(MIN); tCK = tRC(MIN); Address and control inputs change only during Active READ, or WRITE commands. IDD8 TBD TBD TBD mA 22, 49 AUTO REFRESH CURRENT SELF REFRESH CURRENT: CKE 0.2V 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 47 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM ELECTRICAL CHARACTERISTICS AND RECOMMENDED AC OPERATING CONDITIONS (Notes: 1-5, 14-17, 33; notes appear on pages 50-53) (0C TA +70C; VDDQ = +2.5V 0.2V, VDD = +2.5V 0.2V) AC CHARACTERISTICS PARAMETER SYMBOL MIN MAX MIN -75 MAX Access window of DQs from CK/CK# tAC -0.75 +0.75 -0.75 CK high-level width tCH 0.45 0.55 0.45 CK low-level width tCL 0.45 0.55 0.45 0.55 tCK(2.5) 7 12 7.5 12 tCK(2) 7.5 12 10 12 tDH 0.5 Clock cycle time -7 CL = 2.5 CL = 2 DQ and DM input hold time relative to DQS -8 MIN MAX UNITS NOTES +0.75 -0.8 +0.8 ns 0.55 0.45 0.55 tCK 30 0.45 0.55 tCK 30 8 12 ns 52 10 12 ns 52 0.5 0.6 ns 26, 31 DQ and DM input setup time relative to DQS tDS 0.5 0.5 0.6 ns 26, 31 DQ and DM input pulse width (for each input) tDIPW 1.75 1.75 2 ns 31 tDQSCK -0.75 tDQSH 0.35 0.35 0.35 tCK DQS input low pulse width tDQSL 0.35 0.35 0.35 tCK DQS-DQ skew, DQS to last DQ valid, per group, per access tDQSQ Access window of DQS from CK/CK# DQS input high pulse width +0.75 -0.75 0.5 +0.75 -0.8 0.5 +0.8 0.6 ns ns 25, 26 0.8 ns 36 1.25 tCK DQS-DQ skew, first DQS to last DQ valid, per access tDQSQA Write command to first DQS latching transition tDQSS 0.75 DQS falling edge to CK rising - setup time tDSS 0.2 0.2 0.2 tCK DQS falling edge from CK rising - hold time tDSH 0.2 0.2 0.2 tCK Half clock period tHP tCH,tCL tCH,tCL tCH,tCL ns 34 Data-out high-impedance window from CK/CK# tHZ -0.75 +0.75 -0.75 +0.75 -0.8 +0.8 ns 18 Data-out low-impedance window from CK/CK# tLZ -0.75 +0.75 -0.75 +0.75 -0.8 +0.8 ns 18 Address and control input hold time (fast slew rate) tIH F .90 .90 1.1 ns 14 Address and control input setup time (fast slew rate) t IS F .90 .90 1.1 ns 14 Address and control input hold time (slow slew rate) tIH S 1 1 1.1 ns 14 Address and control input setup time (slow slew rate) tIH S 1 1 1.1 ns 14 Address and control input pulse width tIPW 2.2 2.2 2.5 ns LOAD MODE REGISTER command cycle time tMRD 15 15 16 ns DQ-DQS hold, DQS to first DQ to go non-valid, per access 0.7 tQH - 0.7 1.25 tHP tQHS 0.75 - 1.25 tHP tQHS 0.75 - tHP tQHS ns Data hold skew factor tQHS ACTIVE to PRECHARGE command tRAS ACTIVE to READ with Auto precharge command tRAP 15 20 20 ns tRC 60 65 70 ns AUTO REFRESH command period tRFC 67 75 80 ns ACTIVE to READ or WRITE delay tRCD 15 20 20 ns tRP 15 20 20 ns ACTIVE to ACTIVE/AUTO REFRESH command period PRECHARGE command period 0.75 45 120,000 0.75 45 120,000 50 1 ns 120,000 ns DQS read preamble tRPRE 0.9 1.1 0.9 1.1 0.9 1.1 tCK DQS read postamble tRPST 0.4 0.6 0.4 0.6 0.4 0.6 tCK ACTIVE bank a to ACTIVE bank b command tRRD 2 2 2 25, 26, 34 35 50 42 tCK (continued on following page) 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 48 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM ELECTRICAL CHARACTERISTICS AND RECOMMENDED AC OPERATING CONDITIONS (Notes: 1-5, 14-17, 33; notes appear on pages 50-53) (0C TA +70C; VDDQ = +2.5V 0.2V, VDD = +2.5V 0.2V) AC CHARACTERISTICS - Continued PARAMETER DQS write preamble -7 SYMBOL tWPRE MIN 0.25 MAX MIN 0.25 0.6 0.4 -75 MAX -8 MIN 0.25 MAX UNITS NOTES tCK tWPRES 0 DQS write postamble tWPST 0.4 Write recovery time tWR 15 15 15 ns tWTR 1 1 1 tCK DQS write preamble setup time Internal WRITE to READ command delay Data valid output window (DVW) 0 tQH - tDQSQ na REFRESH to REFRESH command interval tREFC Average periodic refresh interval tREFI Terminating voltage delay to VDD tVTD tQH 70.3 7.8 0 0 0.6 0.4 0.6 ns 20, 21 tCK 19 - tDQSQ tQH - tDQSQ ns 25 70.3 70.3 s 23 s 23 7.8 0 7.8 0 ns Exit SELF REFRESH to non-READ command tXSNR 75 75 80 ns Exit SELF REFRESH to READ command tXSRD 200 200 200 tCK SLEW RATE DERATING VALUES (Note: 14; notes appear on pages 50-53) (0C TA +70C; VDDQ = +2.5V 0.2V, VDD = +2.5V 0.2V) ADDRESS / COMMAND tIS tIH 0.500V / ns 1 1 ns -7, -75 0.400V / ns 1.05 1 ns -7, -75 0.300V / ns 1.10 1 ns -7, -75 0.200V / ns 1.15 1 ns -8 0.500V / ns 1.1 1.1 ns -8 0.400V / ns 1.15 1.1 ns -8 0.300V / ns 1.20 1.1 ns -8 0.200V / ns 1.25 1.1 ns SPEED SLEW RATE -7, -75 UNITS SLEW RATE DERATING VALUES (Note: 31; notes appear on pages 50-53) (0C TA +70C; VDDQ = +2.5V 0.2V, VDD = +2.5V 0.2V) Data, DM, DQS SPEED SLEW RATE tDS tDH UNITS -7, -75 0.500V / ns 0.50 0.50 ns -7, -75 0.400V / ns 0.55 0.55 ns -7, -75 0.300V / ns 0.60 0.60 ns -7, -75 0.200V / ns 0.65 0.65 ns -8 0.500V / ns 0.60 0.60 ns -8 0.400V / ns 0.65 0.65 ns -8 0.300V / ns 0.70 0.70 ns -8 0.200V / ns 0.75 0.75 ns 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 49 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM NOTES 1. 2. 3. 12. IDD specifications are tested after the device is properly initialized, and is averaged at the defined cycle rate. 13. This parameter is sampled. VDD = +2.5V 0.2V, VDDQ = +2.5V 0.2V, VREF = VSS, f = 100 MHz, TA = 25C, VOUT(DC) = VDDQ/2, VOUT (peak to peak) = 0.2V. DM input is grouped with I/O pins, reflecting the fact that they are matched in loading. 14. Command/Address input slew rate = 0.5V/ns. For -7 and -75 with slew rates 1V/ns and faster, tIS and tIH are reduced to 900ps. If the slew rate is less than 0.5V/ns, timing must be derated: tIS has an additional 50ps per each 100mV/ns reduction in slew rate from the 500mV/ns. tIH has 0ps added, that is, it remains constant. If the slew rate exceeds 4.5V/ns, functionality is uncertain. 15. The CK/CK# input reference level (for timing referenced to CK/CK#) is the point at which CK and CK# cross; the input reference level for signals other than CK/CK# is VREF. 16. Inputs are not recognized as valid until VREF stabilizes. Exception: during the period before VREF stabilizes, CKE 0.3 x VDDQ is recognized as LOW. 17. The output timing reference level, as measured at the timing reference point indicated in Note 3, is VTT. 18. tHZ and tLZ transitions occur in the same access time windows as valid data transitions. These parameters are not referenced to a specific voltage level, but specify when the device output is no longer driving (HZ) or begins driving (LZ). 19. The maximum limit for this parameter is not a device limit. The device will operate with a greater value for this parameter, but system performance (bus turnaround) will degrade accordingly. 20. This is not a device limit. The device will operate with a negative value, but system performance could be degraded due to bus turnaround. 21. It is recommended that DQS be valid (HIGH or LOW) on or before the WRITE command. The case shown (DQS going from High-Z to logic LOW) applies when no WRITEs were previously in progress on the bus. If a previous WRITE was in progress, DQS could be HIGH during this time, depending on tDQSS. 22. MIN (tRC or tRFC) for IDD measurements is the smallest multiple of tCK that meets the minimum absolute value for the respective parameter. tRAS(MAX) for IDD measurements is the largest multiple of tCK that meets the maximum absolute value for tRAS. All voltages referenced to VSS. Tests for AC timing, IDD, and electrical AC and DC characteristics may be conducted at nominal reference/supply voltage levels, but the related specifications and device operation are guaranteed for the full voltage range specified. Outputs measured with equivalent load: VTT Output (VOUT) 50 Reference Point 30pF 4. AC timing and IDD tests may use a VIL-to-VIH swing of up to 1.5V in the test environment, but input timing is still referenced to VREF (or to the crossing point for CK/CK#), and parameter specifications are guaranteed for the specified AC input levels under normal use conditions. The minimum slew rate for the input signals used to test the device is 1V/ns in the range between VIL(AC) and VIH(AC). 5. The AC and DC input level specifications are as defined in the SSTL_2 Standard (i.e., the receiver will effectively switch as a result of the signal crossing the AC input level, and will remain in that state as long as the signal does not ring back above [below] the DC input LOW [HIGH] level). 6. VREF is expected to equal VDDQ/2 of the transmitting device and to track variations in the DC level of the same. Peak-to-peak noise (noncommon mode) on VREF may not exceed 2 percent of the DC value. Thus, from VDDQ/2, VREF is allowed 25mV for DC error and an additional 25mV for AC noise. 7. VTT is not applied directly to the device. VTT is a system supply for signal termination resistors, is expected to be set equal to VREF and must track variations in the DC level of VREF. 8. VID is the magnitude of the difference between the input level on CK and the input level on CK#. 9. The value of VIX is expected to equal VDDQ/2 of the transmitting device and must track variations in the DC level of the same. 10. IDD is dependent on output loading and cycle rates. Specified values are obtained with minimum cycle time at CL = 2 for -7 and -8, CL = 2.5 for -75 with the outputs open. 11. Enables on-chip refresh and address counters. 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 50 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM NOTES (continued) 27. This limit is actually a nominal value and does not result in a fail value. CKE is HIGH during REFRESH command period (tRFC [MIN]) else CKE is LOW (i.e., during standby). 28. To maintain a valid level, the transitioning edge of the input must: a) Sustain a constant slew rate from the current AC level through to the target AC level, VIL(AC) or VIH(AC). b) Reach at least the target AC level. c) After the AC target level is reached, continue to maintain at least the target DC level, VIL(DC) or VIH(DC). 29. The Input capacitance per pin group will not differ by more than this maximum amount for any given device. 30. CK and CK# input slew rate must be 1V/ns. 31. DQ and DM input slew rates must not deviate from DQS by more than 10%. If the DQ/DM/ DQS slew rate is less than 0.5V/ns, timing must be derated: 50ps must be added to tDS and tDH for each 100mv/ns reduction in slew rate. If slew rate exceeds 4V/ns, functionality is uncertain. 23. The refresh period 64ms. This equates to an average refresh rate of 7.8125s. However, an AUTO REFRESH command must be asserted at least once every 70.3s; burst refreshing or posting by the DRAM controller greater than eight refresh cycles is not allowed. 24. The I/O capacitance per DQS and DQ byte/ group will not differ by more than this maximum amount for any given device. 25. The valid data window is derived by achieving other specifications - tHP (tCK/2), tDQSQ, and tQH (tHP - tQHS). The data valid window derates directly porportional with the clock duty cycle and a practical data valid window can be derived. The clock is allowed a maximum duty cycle variation of 45/55. Functionality is uncertain when operating beyond a 45/55 ratio. The data valid window derating curves are provided below for duty cycles ranging between 50/50 and 45/55. 26. Referenced to each output group: x4 = DQS with DQ0-DQ3; x8 = DQS with DQ0-DQ7; x16 = LDQS with DQ0-DQ7; and UDQS with DQ8DQ15. DERATING DATA VALID WINDOW (tQH - tDQSQ) 3.8 3.750 3.700 3.6 3.650 3.600 3.550 3.400 3.500 3.350 3.4 3.300 3.450 3.400 3.250 3.200 ns 3.300 3.250 3.050 3.000 t -7, -75 @ tCK = 7.5ns t -8 @ tCK = 8ns 2.950 2.900 t -7 @ tCK = 7ns 2.8 2.6 3.100 t -7,-75 @ tCK = 10ns t -8 @ tCK = 10ns 3.0 3.350 3.150 3.2 2.500 2.463 2.425 2.388 2.4 2.350 2.313 2.275 2.238 2.200 2.2 2.163 2.125 2.0 1.8 50/50 49.5/50.5 49/51 48.5/52.5 48/52 47.5/53.5 47/53 46.5/54.5 46/54 45.5/55.5 45/55 Clock Duty Cycle 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 51 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM NOTES (continued) 32. VDD must not vary more than 4% if CKE is not active while any bank is active. 33. The clock is allowed up to 150ps of jitter. Each timing parameter is allowed to vary by the same amount. 34. tHPmin is the lesser of tCL minimum and tCH minimum actually applied to the device CK and CK/ inputs, collectively during bank active. 35. READs and WRITEs with autoprecharge are not allowed to be issued until tRAS(MIN) can be satisfied prior to the internal precharge command being issued. 36. Applies to x16 only. First DQS (LDQS or UDQS) to transition to last DQ (DQ0-DQ15) to transition valid. Initial JEDEC specifications suggested this to be same as tDQSQ. 37.Normal Output Drive Curves: a) The full variation in driver pull-down current from minimum to maximum process, temperature and voltage will lie within the outer bounding lines of the V-I curve of Figure A. b) The variation in driver pull-down current within nominal limits of voltage and temperature is expected, but not guaranteed, to lie within the inner bounding lines of the V-I curve of Figure A. c) The full variation in driver pull-up current from minimum to maximum process, temperature and voltage will lie within the outer bounding lines of the V-I curve of Figure B. d) The variation in driver pull-up current within nominal limits of voltage and temperature is expected, but not guaranteed, to lie within the inner bounding lines of the V-I curve of Figure B. e) The full variation in the ratio of the maximum to minimum pull-up and pull-down current should be between .71 and 1.4, for device drain-to-source voltages from 0.1V to 1.0 Volt, and at the same voltage and temperature. f) The full variation in the ratio of the nominal pull-up to pull-down current should be unity 10%, for device drain-to-source voltages from 0.1V to 1.0 volt. Figure A Pull-Down Characteristics 160 Figure B Pull-Up Characteristics 0 -20 140 -40 120 -60 IOUT (mA) IOUT (mA) 100 80 60 -80 -100 -120 -140 40 -160 20 -180 0 0.0 0.5 1.0 1.5 2.0 -200 2.5 0.0 VOUT (V) 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 0.5 1.0 1.5 2.0 2.5 VDDQ - VOUT (V) 52 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM NOTES (continued) VIL undershoot: VIL(MIN) = -1.5V for a pulse width 3ns and the pulse width can not be greater than 1/3 of the cycle rate. 41. VDD and VDDQ must track each other. 42. Note 42 is not used. 43. Note 43 is not used. 44. During initialization, VDDQ, VTT, and VREF must be equal to or less than VDD + 0.3V. Alternatively, VTT may be 1.35V maximum during power up, even if VDD/VDDQ are 0 volts, provided a minimum of 42 ohms of series resistance is used between the VTT supply and the input pin. 45. Note 45 is not used. 46. Note 46 is not used. 47. Note 47 is not used. 48. Random addressing changing 50% of data changing at every transfer. 49. Random addressing changing 100% of data changing at every transfer. 50. CKE must be active (high) during the entire time a refresh command is executed. That is, from the time the AUTO REFRESH command is registered, CKE must be active at each rising clock edge, until tREF later. 51. IDD2N specifies the DQ, DQS, and DM to be driven to a valid high or low logic level. IDD2Q is similar to IDD2F except IDD2Q specifies the address and control inputs to remain stable. Although IDD2F, IDD2N, and IDD2Q are similar, IDD2F is "worst case." 52. Whenever the operating frequency is altered, not including jitter, the DLL is required to be reset, and followed by 200 clock cycles. 38.Reduced Output Drive Curves: a) The full variation in driver pull-down current from minimum to maximum process, temperature and voltage will lie within the outer bounding lines of the V-I curve of Figure C. b) The variation in driver pull-down current within nominal limits of voltage and temperature is expected, but not guaranteed, to lie within the inner bounding lines of the V-I curve of Figure C. c) The full variation in driver pull-up current from minimum to maximum process, temperature and voltage will lie within the outer bounding lines of the V-I curve of Figure D. d) The variation in driver pull-up current within nominal limits of voltage and temperature is expected, but not guaranteed, to lie within the inner bounding lines of the V-I curve of Figure D. e) The full variation in the ratio of the maximum to minimum pull-up and pull-down current should be between .71 and 1.4 for device drain-to-source voltages from 0.1V to 1.0 Volt, and at the same voltage and temperature. f) The full variation in the ratio of the nominal pull-up to pull-down current should be unity 10%, for device drain-to-source voltages from 0.1V to 1.0 Volt. 39. The voltage levels used are derived from the refernced test load. In practice, the voltage levels obtained from a properly terminated bus will provide significantly different voltage values. 40. VIH overshoot: VIH(MAX) = VDDQ+1.5V for a pulse width 3ns and the pulse width can not be greater than 1/3 of the cycle rate. Figure C Pull-Down Characteristics 80 Figure D Pull-Up Characteristics 0 -5 70 -10 60 -15 IOUT (mA) IOUT (mA) 50 40 30 -20 -25 -30 -35 20 -40 10 -45 0 0.0 0.5 1.0 1.5 2.0 -50 2.5 0.0 VOUT (V) 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 0.2 0.4 0.6 0.8 1.0 VDDQ - VOUT (V) 53 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM NORMAL OUTPUT DRIVE CHARACTERISTICS VOLTAGE (V) 0.1 PULL-DOWN CURRENT (mA) PULL-UP CURRENT (mA) NOMINAL NOMINAL NOMINAL NOMINAL LOW HIGH MINIMUM MAXIMUM LOW HIGH MINIMUM MAXIMUM 6.0 6.8 4.6 9.6 -6.1 -7.6 -4.6 -10.0 0.2 0.3 0.4 0.5 0.6 12.2 18.1 24.1 29.8 34.6 13.5 20.1 26.6 33.0 39.1 9.2 13.8 18.4 23.0 27.7 18.2 26.0 33.9 41.8 49.4 -12.2 -18.1 -24.0 -29.8 -34.3 -14.5 -21.2 -27.7 -34.1 -40.5 -9.2 -13.8 -18.4 -23.0 -27.7 -20.0 -29.8 -38.8 -46.8 -54.4 0.7 0.8 0.9 1.0 39.4 43.7 47.5 51.3 44.2 49.8 55.2 60.3 32.2 36.8 39.6 42.6 56.8 63.2 69.9 76.3 -38.1 -41.1 -43.8 -46.0 -46.9 -53.1 -59.4 -65.5 -32.2 -36.0 -38.2 -38.7 -61.8 -69.5 -77.3 -85.2 1.1 1.2 54.1 56.2 65.2 69.9 44.8 46.2 82.5 88.3 -47.8 -49.2 -71.6 -77.6 -39.0 -39.2 -93.0 -100.6 1.3 1.4 1.5 57.9 59.3 60.1 74.2 78.4 82.3 47.1 47.4 47.7 93.8 99.1 103.8 -50.0 -50.5 -50.7 -83.6 -89.7 -95.5 -39.4 -39.6 -39.9 -108.1 -115.5 -123.0 1.6 1.7 60.5 61.0 85.9 89.1 48.0 48.4 108.4 112.1 -51.0 -51.1 -101.3 -107.1 -40.1 -40.2 -130.4 -136.7 1.8 1.9 2.0 61.5 62.0 62.5 92.2 95.3 97.2 48.9 49.1 49.4 115.9 119.6 123.3 -51.3 -51.5 -51.6 -112.4 -118.7 -124.0 -40.3 -40.4 -40.5 -144.2 -150.5 -156.9 2.1 2.2 62.8 63.3 99.1 100.9 49.6 49.8 126.5 129.5 -51.8 -52.0 -129.3 -134.6 -40.6 -40.7 -163.2 -169.6 2.3 2.4 2.5 2.6 63.8 64.1 64.6 64.8 101.9 102.8 103.8 104.6 49.9 50.0 50.2 50.4 132.4 135.0 137.3 139.2 -52.2 -52.3 -52.5 -52.7 -139.9 -145.2 -150.5 -155.3 -40.8 -40.9 -41.0 -41.1 -176.0 -181.3 -187.6 -192.9 2.7 65.0 105.4 50.5 140.8 -52.8 -160.1 -41.2 -198.2 NOTE: The above characteristics are specified under best, worst, and nominal process variation/conditions. 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 54 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM REDUCED OUTPUT DRIVE CHARACTERISTICS PULL-DOWN CURRENT (mA) PULL-UP CURRENT (mA) VOLTAGE NOMINAL NOMINAL NOMINAL NOMINAL (V) LOW HIGH MINIMUM MAXIMUM LOW HIGH MINIMUM MAXIMUM 0.1 3.4 3.8 2.6 5.0 -3.5 -4.3 -2.6 -5.0 0.2 0.3 0.4 0.5 6.9 10.3 13.6 16.9 7.6 11.4 15.1 18.7 5.2 7.8 10.4 13.0 9.9 14.6 19.2 23.6 -6.9 -10.3 -13.6 -16.9 -7.8 -12.0 -15.7 -19.3 -5.2 -7.8 -10.4 -13.0 -9.9 -14.6 -19.2 -23.6 0.6 19.9 22.1 15.7 28.0 -19.4 -22.9 -15.7 -28.0 0.7 0.8 22.3 24.7 25.0 28.2 18.2 20.8 32.2 35.8 -21.5 -23.3 -26.5 -30.1 -18.2 -20.4 -32.2 -35.8 0.9 1.0 26.9 29.0 31.3 34.1 22.4 24.1 39.5 43.2 -24.8 -26.0 -33.6 -37.1 -21.6 -21.9 -39.5 -43.2 1.1 1.2 30.6 31.8 36.9 39.5 25.4 26.2 46.7 50.0 -27.1 -27.8 -40.3 -43.1 -22.1 -22.2 -46.7 -50.0 1.3 1.4 1.5 32.8 33.5 34.0 42.0 44.4 46.6 26.6 26.8 27.0 53.1 56.1 58.7 -28.3 -28.6 -28.7 -45.8 -48.4 -50.7 -22.3 -22.4 -22.6 -53.1 -56.1 -58.7 1.6 1.7 34.3 34.5 48.6 50.5 27.2 27.4 61.4 63.5 -28.9 -28.9 -52.9 -55.0 -22.7 -22.7 -61.4 -63.5 1.8 1.9 2.0 34.8 35.1 35.4 52.2 53.9 55.0 27.7 27.8 28.0 65.6 67.7 69.8 -29.0 -29.2 -29.2 -56.8 -58.7 -60.0 -22.8 -22.9 -22.9 -65.6 -67.7 -69.8 2.1 2.2 35.6 35.8 56.1 57.1 28.1 28.2 71.6 73.3 -29.3 -29.5 -61.2 -62.4 -23.0 -23.0 -71.6 -73.3 2.3 2.4 2.5 36.1 36.3 36.5 57.7 58.2 58.7 28.3 28.3 28.4 74.9 76.4 77.7 -29.5 -29.6 -29.7 -63.1 -63.8 -64.4 -23.1 -23.2 -23.2 -74.9 -76.4 -77.7 2.6 2.7 36.7 36.8 59.2 59.6 28.5 28.6 78.8 79.7 -29.8 -29.9 -65.1 -65.8 -23.3 -23.3 -78.8 -79.7 NOTE: The above characteristics are specified under best, worst, and nominal process variation/conditions. 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 55 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM T1 T2 T2n T3 T3n T4 CK# CK tHP5 tHP5 tHP5 tHP5 tDQSQ3 tDQSQ3 tQH4 tQH4 tHP5 tHP5 tDQSQ3 tDQSQ3 DQS1 QFC# DQ (Last data valid) DQ2 DQ2 DQ2 DQ2 DQ2 DQ2 DQ (First data no longer valid) tQH4 tQH4 DQ (Last data valid) T2 T2n T3 T3n DQ (First data no longer valid) T2 T2n T3 T3n All DQs and DQS, collectively6 T2 T2n T3 T3n Data Valid window Data Valid window Data Valid window Data Valid window Earliest signal transition Latest signal transition NOTE: 1. DQs transitioning after DQS transition define tDQSQ window. DQS transitions at T2 and at T2n are an "early DQS," at T3 is a "nominal DQS," and at T3n is a "late DQS" 2. For a x4, only two DQs apply. 3. tDQSQ is derived at each DQS clock edge and is not cumulative over time and begins with DQS transition and ends with the last valid transition of DQs . 4. tQH is derived from tHP : tQH = tHP - tQHS. 5. tHP is the lesser of tCL or tCH clock transition collectively when a bank is active. 6. The data valid window is derived for each DQS transitions and is defined as tQH minus tDQSQ. Figure 27 x4, x8 Data Output Timing - tDQSQ, tQH and Data Valid Window 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 56 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM CK# CK T1 T2 tHP5 T2n tHP5 T3 tHP5 tHP5 tDQSQ3 tDQSQ3 tQH4 tQH4 T3n tHP5 T4 tHP5 tDQSQ3 tDQSQ3 LDQS1 tQH4 Lower Byte DQ (Last data valid)2 DQ2 DQ2 DQ2 DQ2 DQ2 DQ2 DQ (First data no longer valid)2 tQH4 DQ (Last data valid)2 T2 T2n T3 T3n DQ (First data no longer valid)2 T2 T2n T3 T3n DQ0 - DQ7 and LDQS, collectively6 T2 T2n T3 T3n Data Valid window Data Valid window Data Valid window Data Valid window tDQSQ3 tDQSQ3 tDQSQ3 tDQSQ3 UDQS1 tQH4 tDQSQA tQH4 tQH4 T2 T2n DQ (First data no longer valid)7 T2 T2n DQ8 - DQ15 and UDQS, collectively6 T2 T2n Data Valid window Data Valid window DQ (Last data valid)7 NOTE: 1. DQs transitioning after DQS transition define tDQSQ window. LDQS defines the lower byte and UDQS defines the upper byte. 2. DQ0, DQ1, DQ2, DQ3, DQ4, DQ5, DQ6, or DQ7. 3. tDQSQ is derived at each DQS clock edge and is not cumulative over time and begins with DQS transition and ends with the last valid transition of DQs . Upper Byte DQ (Last data valid)7 DQ7 DQ7 DQ7 DQ7 DQ7 DQ7 DQ (First data no longer valid)7 tQH4 T3 T3 T3 T3n T3n T3n Data Valid Data Valid window window 4. tQH is derived from tHP: tQH = tHP - tQHS. 5. tHP is the lesser of tCL or tCH clock transition collectively when a bank is active. 6. The data valid window is derived for each DQS transition and is tQH minus tDQSQ. 7. DQ8, DQ9, DQ10, D11, DQ12, DQ13, DQ14, or DQ15. Figure 27 A x16 Data Output Timing - tDQSQ, tQH and Data Valid Window 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 57 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM T07 T1 T2 T3 T2n T3n T4 T4n T5 T5n T6 CK# CK tLZ(MAX) tDQSCK1(MAX) tHZ(MAX) tDQSCK1(MIN) tHZ(MIN) tDQSCK1(MAX) tDQSCK1(MIN) tLZ(MIN) tRPST tRPRE DQS, or LDQS/UDQS2 DQ (Last data valid) T2 T2n T3 T3n T4 T4n T5 T5n DQ (First data valid) T2 T2n T3 T3n T4 T4n T5 T5n All DQs collectively3 T2 T2n T3 T3n T4 T4n T5 T5n tLZ(MIN) NOTE: 1. 2. 3. 4. 5. 6. 7. tLZ(MAX) tAC4(MAX) tAC4(MIN) tHZ(MIN) tHZ(MAX) tDQSCK is the DQS output window relative to CK and is the"long term" component of DQS skew. DQs transitioning after DQS transition define tDQSQ window. All DQs must transition by tDQSQ after DQS transitions, regardless of tAC. tAC is the DQ output window relative to CK, and is the"long term" component of DQ skew. tLZ(MIN), tAC(MIN), and tHZ(MIN) are the first valid signal transition. tLZ(MAX), tAC(MAX), and tHZ(MAX) are the latest valid signal transition. READ command with CL = 2 issued at T0. Figure 28 Data Output Timing - tAC and tDQSCK T03 T1 T1n T2 T2n T3 CK# CK tDQSS tDSH1 tDSS2 tDSH1 tDSS2 DQS tDQSL tDQSH tWPST tWPRES tWPRE DI b DQ DM tDS tDH TRANSITIONING DATA NOTE: 1. tDSH(MIN) generally occurs during tDQSS(MIN). 2. tDSS(MIN) generally occurs during tDQSS(MAX). DON'T CARE 3. WRITE command issued at T0. 4. For x16, LDQS controls the lower byte and UDQS controls the upper byte. Figure 29 Data Input Timing 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 58 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM VDDQ (2.3V minimum) 1 VOH(MIN) (1.670V for SSTL2 termination) System Noise Margin (Power/Ground, Crosstalk, Signal Integrity Attenuation) 1.560V VIHAC 1.400V VIHDC 1.300V 1.275V 1.250V 1.225V 1.200V VREF +AC Noise VREF +DC Error VREF -DC Error VREF -AC Noise 1.100V VILDC VILAC 0.940V VINAC - Provides margin between VOL (MAX) and VILAC VOL (MAX) (0.83V2 for SSTL2 termination) Receiver NOTE: 1. VOH (MIN) with test load is 1.927V 2. VOL (MAX) with test load is 0.373V 3. Numbers in diagram reflect nomimal values utilizing circuit below. VSSQ Transmitter VTT 25 25 Reference Point Figure 30 Input Voltage Waveform 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 59 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM INITIALIZE AND LOAD MODE REGISTERS VDD VDDQ tVTD1 VTT1 VREF T1 T0 (( )) (( )) CK# CK tCH tCL (( )) tIS Tb0 Tc0 Td0 Te0 (( )) (( )) (( )) (( )) (( )) (( )) (( )) (( )) (( )) (( )) (( )) (( )) (( )) (( )) (( )) (( )) (( )) (( )) (( )) (( )) tIH (( )) (( )) 6 (( )) (( )) DM (( )) (( )) (( )) (( )) A0-A9, A11, A12 (( )) (( )) (( )) (( )) A10 (( )) (( )) COMMAND Ta0 (( )) (( )) tIH tIS LVCMOS CKE LOW LEVEL T2 (( )) (( )) NOP PRE tCK LMR tIS tIH AR (( )) (( )) (( )) (( )) AR (( )) (( )) (( )) (( )) (( )) (( )) (( )) (( )) ACT5 (( )) (( )) CODE (( )) (( )) (( )) (( )) (( )) (( )) (( )) (( )) RA (( )) (( )) CODE ( ( ALL BANKS )) (( )) (( )) (( )) (( )) (( )) (( )) (( )) RA (( )) (( )) BA0 = L, BA1 = L (( )) (( )) (( )) (( )) (( )) (( )) (( )) (( )) BA tIH CODE tIS (( )) (( )) (( )) (( )) PRE tIH CODE tIS (( )) (( )) (( )) (( )) LMR (( )) (( )) tIS ALL BANKS (( )) (( )) tIS tIH tIH BA0, BA1 (( )) (( )) DQS (( )) High-Z (( )) (( )) (( )) (( )) (( )) (( )) DQ (( )) High-Z (( )) (( )) (( )) (( )) (( )) (( )) BA0 = H, BA1 = L T = 200s tRP tMRD Load Extended Mode Register Power-up: VDD and CK stable tMRD tRP tRFC tRFC5 200 cycles of CK3 Load Mode Register2 DON'T CARE NOTE: 1. VTT is not applied directly to the device; however, tVTD should be greater than or equal to zero to avoid device latch-up. VDDQ, VDDQ, VTT and VREF must be equal to or less than VDD + 0.3V. Alternatively, VTT may be 1.35V maximum during power up, even if VDD/VDDQ are 0 volts, provided a minimum of 42 ohms of series resistance is used between the VTT supply and the input pin. 2. Although not required by the Micron device, JEDEC specifies resetting the DLL with A8 = H. 3. tMRD is required before any command can be applied, and 200 cycles of CK are required before a READ command can be issued. 4. The two AUTO REFRESH commands at Tc0 and Td0 may be applied after the LOAD MODE REGISTER (LMR) command at Ta0. 5. Although not required by the Micron device, JEDEC specifies issuing another LMR command (A8 = L) prior to activating any bank. 6. PRE = PRECHARGE command, LMR = LOAD MODE REGISTER command, AR = AUTO REFRESH command, ACT = ACTIVE command, RA = Row Address, Bank Address TIMING PARAMETERS -7 -75 -8 -7 SYMBOL tCH MIN 0.45 MAX 0.55 MIN 0.45 MAX 0.55 MIN 0.45 MAX 0.55 UNITS tCK tCL 0.45 7 0.55 12 0.45 7.5 0.55 12 0.45 8 0.55 12 tCK ns tRFC 7.5 1 12 10 1 2 10 1.1 12 ns ns tRP tCK (2.5) tCK (2) tIH 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 SYMBOL tIS tMRD tVTD 60 MIN 1 MAX MIN 1 -75 MAX -8 MIN 1.1 MAX UNITS ns 15 67 15 75 16 80 ns ns 15 0 20 0 20 0 ns ns Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM POWER-DOWN MODE T0 T1 T2 CK# CK tCK tIS tCH tCL (( )) tIH VALID1 tIS ADDR Ta2 tIS CKE COMMAND Ta1 tIS tIH tIS Ta0 (( )) (( )) (( )) (( )) NOP tIH NOP VALID (( )) (( )) VALID DQS (( )) (( )) DQ (( )) (( )) DM (( )) (( )) VALID tREFC Enter 2 Power-Down Mode Exit Power-Down Mode DON'T CARE NOTE: 1. If this command is a PRECHARGE (or if the device is already in the idle state), then the power-down mode shown is precharge power-down. If this command is an ACTIVE (or if at least one row is already active), then the power-down mode shown is active power-down. 2. No column accesses are allowed to be in progress at the time power-down is entered. TIMING PARAMETERS -7 -75 -8 -7 SYMBOL tCH MIN 0.45 MAX 0.55 MIN 0.45 MAX 0.55 MIN 0.45 MAX 0.55 UNITS tCK tCL 0.45 7 0.55 12 0.45 7.5 0.55 12 0.45 8 0.55 12 tCK tIH ns tIS tCK (2.5) 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 SYMBOL tCK (2) 61 MIN 7.5 1 1 -75 MAX 12 MIN 10 1 1 MAX 12 -8 MIN 10 1.1 1.1 MAX 12 UNITS ns ns ns Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM AUTO REFRESH MODE T0 T2 T1 T4 T3 CK# CK tIS tCK tIH tCH CKE tIH NOP 2 NOP2 PRE Ta1 (( )) (( )) VALID tIS COMMAND1 tCL Ta0 (( )) (( )) NOP2 AR (( )) (( )) NOP2 AR5 Tb0 (( )) (( )) (( )) (( )) VALID (( )) (( )) NOP2 Tb1 Tb2 NOP2 ACT (( )) (( )) (( )) (( )) RA (( )) (( )) (( )) (( )) RA (( )) (( )) (( )) (( )) BA DQS4 (( )) (( )) (( )) (( )) DQ4 (( )) (( )) (( )) (( )) DM4 (( )) (( )) (( )) (( )) A0-A9, A11, A121 ALL BANKS A101 ONE BANK tIS BA0, BA11 tIH Bank(s)3 tRP tRFC5 tRFC DON'T CARE NOTE: 1. PRE = PRECHARGE, ACT = ACTIVE, AR = AUTO REFRESH, RA = Row Address, BA = Bank Address. 2. NOP commands are shown for ease of illustration; other valid commands may be possible at these times. CKE must be active during clock positive transitions. 3. "Don't Care" if A10 is HIGH at this point; A10 must be HIGH if more than one bank is active (i.e., must precharge all active banks). 4. DM, DQ, and DQS signals are all "Don't Care"/High-Z for operations shown. 5. The second AUTO REFRESH is not required and is only shown as an example of two back-to-back AUTO REFRESH commands. TIMING PARAMETERS -7 SYMBOL tCH tCL tCK (2.5) tCK (2) -75 -8 -7 MIN 0.45 0.45 MAX 0.55 0.55 MIN 0.45 0.45 MAX 0.55 0.55 MIN 0.45 0.45 MAX 0.55 0.55 UNITS tCK tCK 7 7.5 12 12 7.5 10 12 12 8 10 12 12 ns ns 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 SYMBOL tIH tIS tRFC tRP 62 MIN 1 1 67 15 -75 MAX MIN 1 1 75 20 MAX -8 MIN 1.1 1.1 80 20 MAX UNITS ns ns ns ns Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM SELF REFRESH MODE T0 T1 CK1 tCH tIS tCL COMMAND4 Ta1 tCK t IS tIS tIH CKE1 tIS Ta01 (( )) (( )) CK# NOP (( )) (( )) AR Tb0 (( )) (( )) (( )) tIH (( )) (( )) NOP (( )) (( )) ADDR (( )) (( )) (( )) (( )) DQS (( )) (( )) (( )) (( )) DQ (( )) (( )) (( )) (( )) DM (( )) (( )) (( )) (( )) VALID tIS tIH VALID tXSNR/ tRP2 tXSRD3 Enter Self Refresh Mode Exit Self Refresh Mode DON'T CARE NOTE: 1. Clock must be stable before exiting self refresh mode. That is, the clock must be cycling within specifications by Ta0. 2. Device must be in the all banks idle state prior to entering self refresh mode. 3. tXSNR is required before any non-READ command can be applied, and tXSRD (200 cycles of CK) is required before a READ command can be applied. 4. AR = AUTO REFRESH command. TIMING PARAMETERS -7 SYMBOL tCH MIN 0.45 MAX 0.55 MIN 0.45 tCL 0.45 7 0.55 12 0.45 7.5 7.5 1 12 10 1 tCK (2.5) tCK (2) tIH 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 -75 MAX 0.55 -8 -7 -75 MAX -8 MIN 0.45 MAX 0.55 UNITS tCK 0.55 12 0.45 8 0.55 12 tCK ns tXSNR 15 75 20 75 20 80 ns ns 12 10 1.1 12 ns ns tXSRD 200 200 200 tCK SYMBOL tIS tRP 63 MIN 1 MAX MIN 1 MIN 1.1 MAX UNITS ns Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM BANK READ - WITHOUT AUTO PRECHARGE CK# T1 T0 T2 T3 T4 T5 T5n T6 T6n T7 T8 NOP6 ACT CK tIS tIH tIS tIH tCK tCH tCL CKE COMMAND5 NOP6 NOP6 ACT tIS x4: A0-A9, A11, A12 x8: A0-A11 x16: A0-A9 RA x8: A12 x16: A11, A12 RA READ2 PRE7 NOP6 NOP6 tIH Col n RA RA tIS tIH ALL BANKS A10 RA RA 3 ONE BANK tIS BA0, BA1 tIH Bank x Bank x4 Bank x tRCD Bank x CL = 2 tRP tRAS7 tRC DM tDQSCK(MIN) Case 1: tAC(MIN) and tDQSCK(MIN) tRPST tRPRE DQS tLZ(MIN) DO n DQ1 tLZ(MIN) tAC(MIN) tHZ(MIN) tDQSCK(MAX) Case 2: tAC(MAX) and tDQSCK(MAX) tRPST tRPRE DQS tLZ(MAX) DO n DQ1 tLZ(MAX) NOTE: 1. 2. 3. 4. 5. 6. 7. 8. tAC(MAX) tHZ(MAX) DO n = data-out from column n; subsequent elements are provided in the programmed order. Burst length = 4 in the case shown. Disable auto precharge. "Don't Care" if A10 is HIGH at T5. PRE = PRECHARGE, ACT = ACTIVE, RA = Row Address, BA = Bank Address. NOP commands are shown for ease of illustration; other commands may be valid at these times. The PRECHARGE command can only be applied at T5 if tRAS minimum is met. Refer to figure 27, 27A, and 28 for detailed DQS and DQ timing. 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 64 TRANSITIONING DATA DON'T CARE Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM BANK READ - WITH AUTO PRECHARGE CK# T1 T0 T2 T3 T4 T5 T5n T6 T6n T7 T8 NOP5 ACT CK tIS tIH tIS tIH tCK tCH tCL CKE COMMAND4 NOP5 NOP5 ACT tIS x4: A0-A9, A11,A12 x8: A0-A9, A11 x16: A0-A9 RA x8: A12 x16: A11, A12 RA A10 RA NOP5 NOP5 READ2,6 NOP5 tIH Col n RA RA 3 IS BA0, BA1 tIS RA tIH IH Bank x Bank x tRCD, tRAP6 Bank x CL = 2 tRP tRAS tRC DM Case 1: tAC(MIN) and tDQSCK(MIN) tDQSCK(MIN) tRPST tRPRE DQS tLZ(MIN) DO n DQ1 tLZ(MIN) Case 2: tAC(MAX) and tDQSCK(MAX) tAC(MIN) tHZ(MIN) tDQSCK(MAX) tRPST tRPRE DQS tLZ(MAX) DO n DQ1 tLZ(MAX) NOTE: 1. 2. 3. 4. 5. 6. 7. tAC(MAX) tHZ(MAX) DO n = data-out from column n; subsequent elements are provided in the programmed order. Burst length = 4 in the case shown. Enable auto precharge. ACT = ACTIVE, RA = Row Address, BA = Bank Address. NOP commands are shown for ease of illustration; other commands may be valid at these times. The READ command can only be applied at T3 if tRAP is satisfied at T3 Refer to figure 27, 27A, and 28 for detailed DQS and DQ timing. 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 65 TRANSITIONING DATA DON'T CARE Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM BANK WRITE - WITHOUT AUTO PRECHARGE T1 T0 CK# T2 CK tIS tIH tIS tIH T3 tCK tCH T4 T4n T5 T5n T6 T7 T8 NOP6 NOP6 PRE tCL CKE COMMAND5 NOP6 NOP6 ACT tIS WRITE2 tIH x4: A0-A9, A11, A12 x8: A0-A9, A11 x16: A0-A9 RA x8: A12 x16: A11, A12 RA Col n tIS A10 RA tIS BA0, BA1 NOP6 NOP6 tIH ALL BANKS 3 ONE BANK tIH Bank x Bank x4 Bank x tWR tRCD tRP tRAS tDQSS(NOM) DQS tDQSL tWPRES tWPRE tDQSH tWPST DI b DQ1 DM tDS NOTE: 1. 2. 3. 4. 5. 6. 7. 8. tDH DI n = data-out from column n; subsequent elements are provided in the programmed order. Burst length = 4 in the case shown. Disable auto precharge. "Don't Care" if A10 is HIGH at T8. PRE = PRECHARGE, ACT = ACTIVE, RA = Row Address, BA = Bank Address. NOP commands are shown for ease of illustration; other commands may be valid at these times. tDSH is applicable during tDQSS(MIN) and is referenced from CK T4 or T5. tDSS is applicable during tDQSS(MAX) and is referenced from CK T5 or T6. TRANSITIONING DATA DON'T CARE TIMING PARAMETERS -7 SYMBOL MIN MAX MIN tCH 0.45 0.45 0.55 0.55 0.45 0.45 7 7.5 12 12 7.5 10 tCL tCK (2.5) tCK (2) tDH tDS tDQSH tDQSL tDQSS tDSS -75 MAX -8 -7 MIN MAX UNITS 0.55 0.55 0.45 0.45 0.55 0.55 tCK 12 12 8 10 12 12 ns ns SYMBOL tDSH tIH tCK tIS tRAS MIN 0.2 1 1 45 0.5 0.5 0.35 0.5 0.5 0.35 0.6 0.6 0.35 ns ns tCK tRCD 0.35 0.75 0.35 0.75 0.35 0.75 tCK tWPRES tCK tWPST 0 0.4 tCK tWR 15 1.25 0.2 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 0.2 1.25 0.2 1.25 tRP tWPRE 66 -75 MAX 120,000 15 15 0.25 MIN 0.2 1 1 45 -8 MAX 120,000 20 20 0.25 0.6 0 0.4 15 MIN 0.2 1.1 1.1 50 MAX 120,000 20 20 0.25 0.6 0 0.4 15 UNITS tCK ns ns ns ns ns tCK ns 0.6 tCK ns Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM BANK WRITE - WITH AUTO PRECHARGE T1 T0 CK# T2 CK tIS tIH tIS tIH T3 tCK tCH T4 T4n T5 T5n T6 T7 NOP5 NOP5 T8 tCL CKE COMMAND4 NOP5 NOP5 ACT tIS NOP5 NOP5 WRITE2 NOP5 tIH x4: A0-A9, A11 x8: A0-A9 x16: A0-A8 RA x4: A12 x8: A11, A12 x16: A9, A11, A12 RA Col n 3 A10 RA tIS BA0, BA1 tIS tIH tIH Bank x Bank x tWR tRCD tRP tRAS tDQSS(NOM) DQS tWPRES tWPRE tDQSL tDQSH tWPST DI b DQ1 DM tDS NOTE: 1. 2. 3. 4. 5. 6. 7. tDH DI n = data-out from column n; subsequent elements are provided in the programmed order. Burst length = 4 in the case shown. Enable auto precharge. ACT = ACTIVE, RA = Row Address, BA = Bank Address. NOP commands are shown for ease of illustration; other commands may be valid at these times. tDSH is applicable during tDQSS(MIN) and is referenced from CK T4 or T5. tDSS is applicable during tDQSS(MAX) and is referenced from CK T5 or T6. TRANSITIONING DATA DON'T CARE TIMING PARAMETERS -7 SYMBOL MIN MAX MIN tCH 0.45 0.45 0.55 0.55 0.45 0.45 7 7.5 0.5 12 12 7.5 10 0.5 tCL tCK (2.5) tCK (2) tDH tDS tDQSH tDQSL tDQSS tDSS 0.5 0.35 0.35 0.75 -75 MAX 0.2 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 0.35 0.75 0.2 -7 MAX UNITS 0.55 0.55 0.45 0.45 0.55 0.55 tCK 12 12 8 10 0.6 12 12 ns ns ns tIS ns tRP 0.5 0.35 1.25 -8 MIN 0.6 0.35 1.25 0.35 0.75 0.2 1.25 SYMBOL tDSH tIH tCK tRAS tRCD MIN 0.2 1 1 45 15 120,000 15 0.25 tCK tWPRE tCK tWPRES tCK tWPST 0 0.4 tCK tWR 15 67 -75 MAX MIN 0.2 1 1 45 20 -8 MAX 120,000 20 0.25 0.6 0 0.4 15 MIN 0.2 1.1 1.1 50 20 MAX 120,000 20 0.25 0.6 0 0.4 15 UNITS tCK ns ns ns ns ns tCK ns 0.6 tCK ns Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM WRITE - DM OPERATION T1 T0 CK# T2 CK tIS tIH tIS tIH T3 tCK tCH T4 T4n T5 T5n T6 T7 T8 NOP6 NOP6 PRE tCL CKE COMMAND5 NOP6 tIS WRITE2 NOP6 ACT tIH x4: A0-A9, A11 x8: A0-A9 x16: A0-A8 RA x4: A12 x8: A11, A12 x16: A9, A11, A12 RA A10 RA Col n tIS tIS BA0, BA1 NOP6 NOP6 tIH ALL BANKS 3 ONE BANK tIH Bank x Bank x4 Bank x tWR tRCD tRP tRAS tDQSS(NOM) DQS tDQSL tWPRES tWPRE tDQSH tWPST DI b DQ1 DM tDS NOTE: 1. 2. 3. 4. 5. 6. 7. 8. tDH DI n = data-out from column n; subsequent elements are provided in the programmed order. Burst length = 4 in the case shown. Disable auto precharge. "Don't Care" if A10 is HIGH at T8. PRE = PRECHARGE, ACT = ACTIVE, RA = Row Address, BA = Bank Address. NOP commands are shown for ease of illustration; other commands may be valid at these times. tDSH is applicable during tDQSS(MIN) and is referenced from CK T4 or T5. tDSS is applicable during tDQSS(MAX) and is referenced from CK T5 or T6. TRANSITIONING DATA DON'T CARE TIMING PARAMETERS -7 SYMBOL tCH tCL tCK (2.5) tCK (2) tDH tDS tDQSH tDQSL tDQSS tDSS -75 -8 -7 MIN 0.45 0.45 MAX 0.55 0.55 MIN 0.45 0.45 MAX 0.55 0.55 MIN 0.45 0.45 MAX 0.55 0.55 UNITS tCK tCK 7 7.5 12 12 7.5 10 12 12 8 10 12 12 ns ns tIS tRCD SYMBOL tDSH tIH tRAS 0.5 0.5 0.5 0.5 0.6 0.6 ns ns 0.35 0.35 0.35 0.35 0.35 0.35 tCK tWPRE tCK tWPRES tCK tWPST tCK tWR 0.75 0.2 1.25 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 0.75 0.2 1.25 0.75 0.2 1.25 tRP 68 MIN 0.2 1 1 45 -75 MAX 120,000 MIN 0.2 1 1 45 -8 MAX 120,000 MIN 0.2 1.1 1.1 50 MAX 120,000 UNITS tCK ns ns ns 15 15 20 20 20 20 ns ns 0.25 0 0.25 0 0.25 0 tCK 0.4 15 0.6 0.4 15 0.6 0.4 15 ns 0.6 tCK ns Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM (TH) OPTION 66-PIN PLASTIC TSOP (400 MIL) 27.00 0.08 0.65 TYP SEE DETAIL A 3.10 0.32 0.075 TYP 11.76 0.10 10.16 0.08 PIN #1 ID 0.15 +0.03 -0.02 GAGE PLANE 0.25 0.10 1.20 MAX 0.10 +0.10 -0.05 0.80 TYP 0.50 0.10 DETAIL A NOTE: MAX or typical here noted. MIN 2. Package width and length do not include mold protrusion; allowable mold protrusion is 0.25mm per side. 1. All dimensions in millimeters 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 69 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc. ADVANCE 512Mb: x4, x8, x16 DDR SDRAM (TG) OPTION 66-PIN PLASTIC TSOP (400 MIL) SEE DETAIL A 22.22 0.08 0.71 0.65 TYP 0.10 (2X) 0.32 .075 TYP 11.76 0.10 10.16 0.08 +0.03 0.15 -0.02 PIN #1 ID GAGE PLANE 0.10 0.25 +0.10 -0.05 0.10 0.80 TYP 1.20 MAX 0.50 0.10 DETAIL A NOTE: MAX or typical here noted. MIN 2. Package width and length do not include mold protrusion; allowable mold protrusion is 0.25mm per side. 1. All dimensions in millimeters 8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-3900 E-mail: prodmktg@micronsemi.com, Internet: http://www.micronsemi.com, Customer Comment Line: 800-932-4992 Micron is a registered trademark of Micron Technology, Inc. 512Mb: x4, x8, x16 DDR SDRAM 512Mx4x8x16DDR_A.p65 - Rev. A; Pub 10/00 70 Micron Technology, Inc., reserves the right to change products or specifications without notice. (c)2000, Micron Technology, Inc.