SMQ-Series(Snap-in) ALUMINUM ELECTROLYTIC CAPACITORS LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS Inverter-use screw terminal, 85C RWF @Rated voltage range : 350 to 550Vdc @Endurance with ripple current : 85C 2000 hours longer life RWE ?SPECIFICATIONS Items Category Temperature Range Rated Voltage Range Capacitance Tolerance Leakage Current Dissipation Factor (tane) Low Temperature Characteristics Insulation Resistance Insulation Withstanding Voltage Endurance Shelf Life Characteristics -25 to +85C 350 to 550Vdc P20% (M) I=0.02CV or 5mA, whichever is smaller. Where, I : Max. leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (V) (at 20C, 120Hz) (at 20C after 5 minutes) 0.25 max. (at 20C, 120Hz) Rated Voltage (Vdc) 350 to 450V 500 & 550V C(-25C)/C(+20C) ]0.7 ]0.6 (at 120Hz) When measured between the terminals shorted each other and the mounting clamp on the insulating sleeve covering the case by using an insulation resistance meter of 500Vdc, the insulation resistance shall not be less than 100MO. When a voltage of 2000Vac is applied for 1 minute between the terminals shorted each other and the mounting clamp on the insulating sleeve covering the case, there shall not be electrical damage. The following specifications shall be satisfied when the capacitors are restored to 20C after subjected to DC voltage with the rated ripple current is applied for 2000 hours at 85C. Capacitance change [P20% of the initial value D.F. (tanE) [300% of the initial specified value Leakage current [The initial specified value The following specifications shall be satisfied when the capacitors are restored to 20C after exposing them for 500 hours at 85C without voltage applied. Capacitance change [P20% of the initial value D.F. (tanE) [300% of the initial specified value Leakage current [The initial specified value Capacitance change ?DIMENSIONS (Terminal Type=LGSN) [mm] @B Type of Mounting Clamp AP1 WP1 8 J GP1 fD 35 50 63.5 76 F35 to F63.5 : G=6 F76 & F89 : G=5 A 58 78 90 104.5 B 44 64 76 90 W 48 68 80 93.5 H 3.5 4.5 4.5 4.5 F 12.7 22.4 28.0 31.5 fD 50 63.5 76 89 4.5 KP1 EP1 6 30P5 360 3 45P5 H BP1 FP1 L+4max. FD+1.8max. Sleeve @C Type of Mounting Clamp E 32.5 38.1 44.5 50.8 K 37.0 43.5 50.0 56.5 F 22.4 28.0 31.5 31.5 J 14.0 14.0 14.0 16.0 <Screw specifications> Plus hexagon-headed screw: M5B0.8B10 Maximum screw tightening torque: 3.23Nm * The screw and the mounting clamp are separately supplied and not attached to the product. ?PART NUMBERING SYSTEM RWE 550 LGSN 820 M C C13 Case code Type of mounting clamp, if required Capacitance tolerance (P20%) Nominal capacitance in MF Screw terminal type Rated voltage in volts Series name (1/2) CAT. No. E1001D SMQ-Series(Snap-in) ALUMINUM ELECTROLYTIC CAPACITORS LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS Inverter-use screw terminal, 85C ?STANDARD RATINGS Vdc mF 350 400 450 500 550 A5 0.6 A8 1.0 A10 1.3 100 Case code 120 A5 270 A5 330 A5 390 1.6 1.7 1.9 A8 470 A8 1.2 A10 1.4 A12 1.6 A12 1.7 C7 1.7 A8 680 C7 1.8 2.7 A10 3.1 C9 A10 3.4 A12 3.5 C11 C7 3.9 2.9 820 1,000 A10 3.8 A12 3.9 1,200 A12 4.2 C7 4.2 1,500 C7 4.7 C9 6.3 D9 8.8 E9 12.0 D11 3,900 D13 8.8 10.3 2.5 C11 D11 2.7 3.0 2.9 C13 D13 3.1 3.5 C13 D9 3.4 3.4 D11 E9 4.5 4.6 E9 4.2 E11 5.0 C13 6.5 D13 5.2 E13 5.8 D9 7.2 E11 6.1 E15 7.0 D9 7.9 E15 7.7 D11 9.5 F15 9.3 E9 10.9 D11 D13 10.6 8.6 E9 10.0 E11 11.5 E11 12.6 E13 13.3 E15 15.7 F15 18.6 E11 12.6 E13 14.5 6,800 E13 15.9 E15 17.3 8,200 E15 19.0 F15 22.5 F15 12,000 2.5 7.2 5,600 10,000 5.6 2.1 5.7 D13 11.7 4.7 D9 C9 2,700 C13 C9 C11 C9 C13 1,800 2,200 2.4 A8 560 4,700 0.7 Rated ripple current (Arms) at 85C, 120Hz 180 3,300 A5 9.8 F15 10.1 20.5 ?CASE CODE L (mm) fD (mm) 35 50 63.5 76 89 75 C7 - 50 A5 - 80 A8 - 96 C9 D9 E9 - 100 A10 - 115 C11 D11 E11 - 120 A12 - 130 C13 D13 E13 - 155 E15 F15 ?RATED RIPPLE CURRENT MULTIPLIERS @Frequency Multipliers Frequency (Hz) Coefficient 50 0.8 120 1.0 300 1.1 1k 1.3 3k 1.4 Note : The endurance of capacitors is shorted with internal heating produced by ripple current at the rate of halving the lifetime with every 5 to 10C rise. When long life performance is required in actual use, the rms ripple current has to be reduced. Also, for the RWE series capacitors, using them at operating voltage less than their rated voltage can extend their lifetime. For the details, please contact a representative of Nippon Chemi-Con. (2/2) CAT. No. E1001D