M36P0R9070E0 512 Mbit (x16, Multiple Bank, Multi-Level, Burst) Flash memory 128 Mbit (Burst) PSRAM, 1.8V supply, Multi-Chip Package Feature summary Multi-Chip Package - 1 die of 512 Mbit (32Mb x 16, Multiple Bank, Multi-Level, Burst) Flash Memory - 1 die of 128Mbit (8Mb x16) PSRAM Supply voltage - VDDF = VCCP = VDDQ = 1.7 to 1.95V - VPPF = 9V for fast program Electronic signature - Manufacturer Code: 20h - Device Code: 8819 ECOPACK(R) package available FBGA TFBGA107 (ZAC) Flash memory Synchronous / Asynchronous Read - Synchronous Burst Read mode: 108MHz, 66MHz - Asynchronous Page Read mode - Random Access: 96ns Programming time - 4.2s typical Word program time using Buffer Enhanced Factory Program command Memory organization - Multiple bank memory array: 64 Mbit banks - Four Extended Flash Array (EFA) Blocks of 64 Kbits Dual operations - program/erase in one Bank while read in others - No delay between read and write operations Security - 2112-bit user programmable OTP Cells - 64-bit unique device number 100,000 program/erase cycles per block Common Flash Interface (CFI) November 2007 Block locking - All Blocks locked at power-up - Any combination of Blocks can be locked with zero latency - WPF for Block Lock-Down - Absolute Write Protection with VPPF = VSS PSRAM Access time: 70ns User-selectable operating modes - Asynchronous modes: Random Read, and Write, Page Read - Synchronous modes: NOR-Flash, Full Synchronous (Burst Read and Write) Asynchronous Page Read - Page Size: 4, 8 or 16 Words - Subsequent Read Within Page: 20ns Burst Read - Fixed Length (4, 8, 16 or 32 Words) or Continuous - Maximum Clock Frequency: 80MHz Low Power Consumption - Active Current: < 25mA - Standby Current: 200A - Deep Power-Down Current: 10A Low Power Features - Partial Array Self Refresh (PASR) - Deep Power-Down (DPD) Mode Rev 3 1/23 www.numonyx.com 1 Contents M36P0R9070E0 Contents 1 Summary description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2 Signal descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.1 Address inputs (A0-A24) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.2 Data input/output (DQ0-DQ15) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.3 Latch Enable (L) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.4 Clock (K) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.5 Wait (WAIT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.6 Flash Chip Enable input (EF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.7 Flash Output Enable inputs (GF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.8 Flash Write Enable (WF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.9 Flash Write Protect (WPF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.10 Flash Reset (RPF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.11 PSRAM Chip Enable input (EP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.12 PSRAM Write Enable (WP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.13 PSRAM Output Enable (GP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.14 PSRAM Upper Byte Enable (UBP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.15 PSRAM Lower Byte Enable (LBP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.16 PSRAM Configuration Register Enable (CRP) . . . . . . . . . . . . . . . . . . . . . 11 2.17 Deep Power-Down input (DPDF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2.18 VDDF Supply Voltages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2.19 VCCP Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2.20 VDDQ Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2.21 VPPF Program Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2.22 VSS Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 3 Functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 4 Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 5 DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2/23 M36P0R9070E0 Contents 6 Package mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 7 Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 8 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 3/23 List of tables M36P0R9070E0 List of tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 7. Table 8. 4/23 Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Main operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Operating and AC measurement conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 M36P0R9070E0 List of figures List of figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 TFBGA connections (top view through package) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Functional block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 AC measurement I/O waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 AC measurement load circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 TFBGA107 8 x 11mm - 9 x 12 active ball array, 0.8mm pitch, package outline. . . . . . . . . 19 5/23 Summary description 1 M36P0R9070E0 Summary description The M36P0R9070E0 combines two memory devices in one Multi-Chip Package: 512-Mbit Multiple Bank Flash memory (the M58PR512J). 128 Mbit PSRAM (the M69KB128AB). The purpose of this document is to describe how the two memory components operate with respect to each other. It should be read in conjunction with the M58PRxxxJ and M69KB128AB datasheets, where all specifications required to operate the Flash memory and PSRAM components are fully detailed. The M58PR512J and M69KB128AB datasheets are available from www.numonyx.com. Recommended operating conditions do not allow more than one memory to be active at the same time. The memory is offered in a Stacked TFBGA107 package. It is supplied with all the bits erased (set to `1'). Figure 1. Logic diagram VDDF VDDQ VCCP VPPF 25 16 DQ0-DQ15 A0-A24 EF WAIT GF WF RPF WPF L M36P0R9070E0 K DPDF EP GP WP CRP UBP LBP VSS 6/23 AI10845 M36P0R9070E0 Summary description Table 1. A0-A24 Signal names (1) Address Inputs DQ0-DQ15 Common Data Input/Output VDDQ Common Flash and PSRAM Power Supply for I/O Buffers VPPF Flash Memory Optional Supply Voltage for Fast Program & Erase VDDF Flash Memory Power Supply VCCP PSRAM Power Supply VSS Ground L Latch Enable input K Burst Clock WAIT Wait Output NC Not Connected Internally DU Do Not Use as Internally Connected Flash Memory EF Chip Enable input GF Output Enable Input WF Write Enable input RPF Reset input WPF Write Protect input DPDF Deep Power-Down PSRAM EP Chip Enable Input GP Output Enable Input WP Write Enable Input CRP Configuration Register Enable Input UBP Upper Byte Enable Input LBP Lower Byte Enable Input 1. A23-A24 are Address Inputs for the Flash memory component only. 7/23 Summary description Figure 2. M36P0R9070E0 TFBGA connections (top view through package) 1 A 2 3 4 5 6 7 DU NC NC NC VCCP DPDF 8 9 VSS DU B DU A4 A18 A19 VSS VDDF NC A21 A11 C NC A5 LBP A23 VSS NC K A22 A12 D VSS A3 A17 A24 VPP WP EP A9 A13 E VSS A2 A7 NC WPF L A20 A10 A15 F NC A1 A6 UBP RPF WF A8 A14 A16 G VDDQ A0 DQ8 DQ2 DQ10 DQ5 DQ13 WAIT NC H VSS GP DQ0 DQ1 DQ3 DQ12 DQ14 DQ7 DU J DU NC GF DQ9 DQ11 DQ4 DQ6 DQ15 VDDQ K NC EF NC NC NC VCCP NC VDDQ CRP L DU VSS VSS VDDQ VDDF VSS VSS VSS VSS M DU NC DU DU DU DU DU DU DU AI11098b 8/23 M36P0R9070E0 2 Signal descriptions Signal descriptions See Figure 1., Logic diagram and Table 1., Signal names, for a brief overview of the signals connected to this device. 2.1 Address inputs (A0-A24) Addresses A0-A22 are common inputs for the Flash memory and PSRAM components. Addresses A23 and A24 are inputs for Flash memory components only. The Address Inputs select the cells in the memory array to access during Bus Read operations. During Bus Write operations they control the commands sent to the Command Interface of the internal state machine. The Flash memory is accessed through the Chip Enable signal (EF) and through the Write Enable signal (WF), while the PSRAM is accessed through the Chip Enable signal (EP) and the Write Enable signal (WP). EF Low, and EP must not be Low at the same time. 2.2 Data input/output (DQ0-DQ15) The Data I/O output the data stored at the selected address during a Bus Read operation or input a command or the data to be programmed during a Bus Write operation. For the PSRAM component, the upper Byte Data Inputs/Outputs (DQ8-DQ15) carry the data to or from the upper part of the selected address when Upper Byte Enable (UBP) is driven Low. The lower Byte Data Inputs/Outputs (DQ0-DQ7) carry the data to or from the lower part of the selected address when Lower Byte Enable (LBP) is driven Low. When both UBP and LBP are disabled, the Data Inputs/ Outputs are high impedance. 2.3 Latch Enable (L) The Latch Enable pin is common to the Flash memory and PSRAM components. For details of how the Latch Enable signal behaves, please refer to the datasheets of the respective memory components: M69KB128AB for the PSRAM and M58PR512J for the Flash memory. 2.4 Clock (K) The Clock input pin is common to the Flash memory and PSRAM components. For details of how the Clock signal behaves, please refer to the datasheets of the respective memory components: M69KB128AB for the PSRAM and M58PR512J for the Flash memory. 9/23 Signal descriptions 2.5 M36P0R9070E0 Wait (WAIT) WAIT is an output pin common to the Flash memory and PSRAM components. However the WAIT signal does not behave in the same way for the PSRAM and the Flash memory. For details of how it behaves, please refer to the M69KB128AB datasheet for the PSRAM and to the M58PR512J datasheet for the Flash memory. 2.6 Flash Chip Enable input (EF) The Flash Chip Enable input activates the control logic, input buffers, decoders and sense amplifiers of the Flash memory component selected. When Chip Enable is Low, VIL, and Reset is High, VIH, the device is in active mode. When Chip Enable is at VIH the corresponding Flash memory are deselected, the outputs are high impedance and the power consumption is reduced to the standby level. It is not allowed to have EF at VIL and EP at VIL at the same time. Only one memory component can be enabled at a time. 2.7 Flash Output Enable inputs (GF) The Output Enable pins control the data outputs during Flash memory Bus Read operations. 2.8 Flash Write Enable (WF) The Write Enable controls the Bus Write operation of the Flash memory Command Interface. The data and address inputs are latched on the rising edge of Chip Enable or Write Enable whichever occurs first. 2.9 Flash Write Protect (WPF) Write Protect is an input that gives an additional hardware protection for each block. When Write Protect is Low, VIL, Lock-Down is enabled and the protection status of the LockedDown blocks cannot be changed. When Write Protect is at High, VIH, Lock-Down is disabled and the Locked-Down blocks can be locked or unlocked. (See the Lock Status Table in the M58PR512J datasheet). 10/23 M36P0R9070E0 2.10 Signal descriptions Flash Reset (RPF) The Reset input provides a hardware reset of the Flash memories. When Reset is at VIL, the memory is in Reset mode: the outputs are high impedance and the current consumption is reduced to the Reset Supply Current IDD2. Refer to the M58PRxxxJ datasheet, for the value of IDD2. After Reset all blocks are in the Locked state and the Configuration Register is reset. When Reset is at VIH, the device is in normal operation. Exiting Reset mode the device enters Asynchronous Read mode, but a negative transition of Chip Enable or Latch Enable is required to ensure valid data outputs. The Reset pin can be interfaced with 3V logic without any additional circuitry. It can be tied to VRPH (refer to the M58PRxxxJ datasheet). 2.11 PSRAM Chip Enable input (EP) The Chip Enable input activates the PSRAM when driven Low (asserted). When deasserted (VIH), the device is disabled, and goes automatically in low-power Standby mode or Deep Power-down mode. 2.12 PSRAM Write Enable (WP) Write Enable, WP, controls the Bus Write operation of the PSRAM. When asserted (VIL), the device is in Write mode and Write operations can be performed either to the configuration registers or to the memory array. 2.13 PSRAM Output Enable (GP) Output Enable, GP, provides a high speed tri-state control, allowing fast read/write cycles to be achieved with the common I/O data bus. 2.14 PSRAM Upper Byte Enable (UBP) The Upper Byte En-able, UBP, gates the data on the Upper Byte Data Inputs/Outputs (DQ8DQ15) to or from the upper part of the selected address during a Write or Read operation. 2.15 PSRAM Lower Byte Enable (LBP) The Lower Byte Enable, LBP, gates the data on the Lower Byte Data Inputs/Outputs (DQ0DQ7) to or from the lower part of the selected address during a Write or Read operation. If both LBP and UBP are disabled (High) during an operation, the device will disable the data bus from receiving or transmitting data. Although the device will seem to be deselected, it remains in an active mode as long as EP remains Low. 2.16 PSRAM Configuration Register Enable (CRP) When this signal is driven High, VIH, Write operations load either the value of the Refresh Configuration Register (RCR) or the Bus configuration register (BCR). 11/23 Signal descriptions 2.17 M36P0R9070E0 Deep Power-Down input (DPDF) The Deep Power-Down input is used to place the device in a Deep Power-Down mode.When the device is in Deep Power-Down mode, the memory cannot be modified and data is protected. For further details on how the Deep Power-Down input signal works, please refer to the M58PR512J datasheet. 2.18 VDDF Supply Voltages VDDF provides the power supply to the internal cores of the Flash memory. It is the main power supply for all Flash memory operations (Read, Program and Erase). 2.19 VCCP Supply Voltage VCCP provides the power supply to the internal core of the PSRAM device. It is the main power supply for all PSRAM operations. 2.20 VDDQ Supply Voltage VDDQ provides the power supply for the Flash memory and PSRAM I/O pins. This allows all Outputs to be powered independently of the Flash memory and SRAM core power supplies, VDDF and VCCP. 2.21 VPPF Program Supply Voltage VPPF is both a control input and a power supply pin for the Flash memory. The two functions are selected by the voltage range applied to the pin. If VPPF is kept in a low voltage range (0V to VDDQ) VPPF is seen as a control input. In this case a voltage lower than VPPLK gives an absolute protection against Program or Erase, while VPPF > VPP1 enables these functions (see the M58PRxxxJ datasheet for the relevant values). VPPF is only sampled at the beginning of a Program or Erase; a change in its value after the operation has started does not have any effect and Program or Erase operations continue. If VPPF is in the range of VPPH it acts as a power supply pin. In this condition VPPF must be stable until the Program/Erase algorithm is completed. 12/23 M36P0R9070E0 2.22 Signal descriptions VSS Ground VSS is the common ground reference for all voltage measurements in the Flash (core and I/O Buffers) and PSRAM chips. It must be connected to the system ground. Note: Each Flash memory device in a system should have their supply voltage (VDDF) and the program supply voltage VPPF decoupled with a 0.1F ceramic capacitor close to the pin (high frequency, inherently low inductance capacitors should be as close as possible to the package). See Figure 5., AC measurement load circuit. The PCB track widths should be sufficient to carry the required VPPF program and erase currents. 13/23 Functional description 3 M36P0R9070E0 Functional description The PSRAM and Flash memory components have separate power supplies but share the same grounds. They are distinguished by two Chip Enable inputs: EF for Flash and EP for the PSRAM. Recommended operating conditions do not allow more than one device to be active at a time. The most common example is a simultaneous read operations on the Flash memory and the PSRAM which would result in a data bus contention. Therefore it is recommended to put the other devices in the high impedance state when reading the selected device. Figure 3. Functional block diagram VDDF VPPF EF GF A23-A24 DPDF WF RPF WPF 512 Mbit Flash Memory A0-A22 DQ0-DQ15 WAIT L K VCCP EP GP VSS V DDQ 128Mbit PSRAM WP CRP UBP LBP Ai11731 14/23 M36P0R9070E0 Table 2. Main operating modes(1) Flash memory Operation EF GF WF RPF DPDF WAIT (2) (3) L Bus Read VIL VIL VIH VIH de-a(4) VIL(5) Bus Write (4) VIL VIH VIL VIH de-a (5) Address Latch VIL X VIH VIH de-a(4) VIL Output Disable VIL VIH VIH VIH de-a(4) Hi-Z Standby Reset Deep PowerDown VIH X X X VIH A0A17 DQ0- DQ8EP WP GP UBP LBP CRP A19 A18 A20- DQ7 DQ15 A22 Data Output Data Input PSRAM must be disabled VIL Data Output or Hi-Z(6) X Hi-Z Hi-Z de-a(4) Hi-Z X (4) X X VIL de-a Hi-Z X VIH X X VIH a(7) Hi-Z X Any PSRAM mode is allowed Hi-Z Hi-Z Word Read VIL VIL VIL VIL Valid Output Output Valid Valid Lower Byte Read VIH VIL VIH VIL VIL Valid Output High-Z Valid Upper Byte Read VIL VIL VIH VIL Valid High-Z Output Valid Word Write X VIL VIL VIL Valid Input Valid Input Valid VIL X VIH VIL VIL Valid Input Invalid Valid X VIL VIH VIL Valid Lower Byte Write PSRAM Functional description The Flash memory must Low- VIL be disabled Z VIL Upper Byte Write Invalid Input Valid Read CR (CR Controlled Method) VIH VIL VIL VIL Program CR (CR Controlled)(9) VIH X X X No Operation X X X X VIL X X X X VIH X X X X X X X X High-Z VIH X X X X VIL X X X High-Z Deep PowerDown(10) VIH Any Flash memory mode is allowed Hi-Z Standby X 00(RCR)1 0(BCR)X1 (DIDR)(8) X 00(RCR) BCR/ 10(BCR) RCR (8) Data BCR/RCR/ DIDR Content High-Z 1. X = Don't care, de-a = de-asserted, a = asserted, CR = Configuration Register. 2. The DPDF signal polarity depends on the value of the ECR14 bit. 3. In the Flash memory the WAIT signal polarity is configured using the Set Configuration Register command. 4. If ECR15 is set to '0', the Flash memory cannot enter the Deep Power-Down mode, even if DPDF is asserted. 5. In the Flash memory L can be tied to VIH if the valid address has been previously latched. 6. Depends on GF. 7. ECR15 has to be set to `1' for the Flash memory to enter Deep Power-Down. 8. A18 and A19 are used to select the BCR, RCR or DIDR registers. 9. BCR and RCR only. 10. Bit 4 of the Refresh Configuration Register must be set to `0', bit 4 (BCR4) of the Bus Configuration Register must be set to `0', and E has to be maintained High, VIH, during Deep Power-Down mode. 15/23 Maximum rating 4 M36P0R9070E0 Maximum rating Stressing the device above the rating listed in the Absolute Maximum Ratings table may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the Numonyx SURE Program and other relevant quality documents. Table 3. Absolute maximum ratings Value Symbol Unit Min Max Ambient Operating Temperature -30 85 C TBIAS Temperature Under Bias -30 85 C TSTG Storage Temperature -55 125 C VIO Input or Output Voltage -0.2 2.45 V VDD Supply Voltage -0.2 2.45 V Input/Output Supply Voltage -0.2 2.45 V Program Voltage -1.0 11.5 V Output Short Circuit Current 100 mA Time for VPP at VPPH 100 hours TA VDDQ VPP IO tVPPH 16/23 Parameter M36P0R9070E0 5 DC and AC parameters DC and AC parameters This section summarizes the operating measurement conditions, and the DC and AC characteristics of the device. The parameters in the DC and AC characteristics Tables that follow, are derived from tests performed under the Measurement Conditions summarized in Table 4., Operating and AC measurement conditions. Designers should check that the operating conditions in their circuit match the operating conditions when relying on the quoted parameters. Table 4. Operating and AC measurement conditions Flash memory PSRAM Parameter Unit Min Max Min Max VCCP Supply Voltage - - 1.7 1.95 V VDDF Supply Voltage 1.7 1.95 - - V VDDQ Supply Voltage 1.7 1.95 1.7 1.95 V VPPF Supply Voltage (Factory environment) 8.5 9.5 - - V VPPF Supply Voltage (Application environment) -0.4 VDDQ +0.4 - - V Ambient Operating Temperature -30 85 -30 85 C Load Capacitance (CL) 30 30 pF Impedance Output (Z0) 50 Output Circuit Protection Resistance (R) 50 Input Rise and Fall Times 3 Input Pulse Voltages Input and Output Timing Ref. Voltages Figure 4. 2 ns 0 to VDDQ 0 to VDDQ V VDDQ/2 VDDQ/2 V AC measurement I/O waveform VDDQ VDDQ/2 0V AI06161 17/23 DC and AC parameters Figure 5. M36P0R9070E0 AC measurement load circuit VCCQ/2 R DEVICE UNDER TEST OUT Z0 CL AI06162a Table 5. Capacitance(1) Symbol Parameter Test Condition CIN Input Capacitance COUT Output Capacitance Min Max Unit VIN = 0V 14 pF VOUT = 0V 14 pF 1. Sampled only, not 100% tested. Please refer to the M58PRxxxJ and M69KB128AB datasheets for further DC and AC characteristic values and illustrations. 18/23 M36P0R9070E0 6 Package mechanical Package mechanical In order to meet environmental requirements, Numonyx offers these devices in ECOPACK(R) packages. These packages have a Lead-free second-level interconnect. The category of Second-Level Interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. Figure 6. TFBGA107 8 x 11mm - 9 x 12 active ball array, 0.8mm pitch, package outline D D1 FD e ddd SE E E1 BALL "B1" FE A e b A2 A1 BGA-Z85 1. Drawing is not to scale. 19/23 Package mechanical Table 6. M36P0R9070E0 Stacked TFBGA107 8 x 11mm - 9 x 12 active ball array, 0.8mm pitch, package mechanical data millimeters inches Symbol Typ Min A Typ Min 1.20 A1 Max 0.047 0.20 0.008 A2 0.85 0.033 b 0.35 0.30 0.40 0.014 0.012 0.016 D 8.00 7.90 8.10 0.315 0.311 0.319 D1 6.40 0.252 ddd 20/23 Max 0.10 10.90 11.10 0.004 E 11.00 0.433 E1 8.80 0.346 e 0.80 0.031 FD 0.80 0.031 FE 1.10 0.043 SE 0.40 0.016 0.429 0.437 M36P0R9070E0 7 Part numbering Part numbering Table 7. Ordering information scheme M36 P Example: Device Type M36 = Multi-Chip Package (Multiple Flash + PSRAM) 0 R 9 0 7 0 E 0 ZAC E Flash 1 Architecture P = Multi-Level, Multiple Bank, Large Buffer Flash 2 Architecture 0 = No Die Operating Voltage R = VDDF = VCCP = VDDQ = 1.7 to 1.95V Flash 1 Density 9 = 512 Mbits Flash 2 Density 0 = No Die RAM 1 Density 7 = 128 Mbits RAM 0 Density 0 = No Die Parameter Blocks Location E = Even Block Flash Memory Configuration Product Version 0 = 90nm Flash technology, 96ns speed; PSRAM Package ZAC= stacked TFBGA107 C stacked footprint. Option Blank = Standard Packing E = ECOPACK(R) Package, Standard packing F = ECOPACK(R) Package, Tape & Reel packing Note: Devices are shipped from the factory with the memory content bits erased to '1'. For a list of available options (Speed, Package, etc.) or for further information on any aspect of this device, please contact the Numonyx Sales Office nearest to you. 21/23 Revision history 8 M36P0R9070E0 Revision history Table 8. 22/23 Document revision history Date Revision Changes 28-Nov-2005 1 Initial release. 13-Jul-2006 2 Document status promoted from Preliminary data to full Datasheet. Document updated to latest version of M58PRxxxJ datasheet, DC characteristics tables removed (for values refer to M58PRxxxJ and M69KB128AB datasheets). PSRAM part replaced by M69KB128AB. H9 ball is DU in Figure 2: TFBGA connections (top view through package). TSTG min and VPP max modified in Table 3: Absolute maximum ratings. Table 2: Main operating modes modified. PSRAM value for Input Rise and Fall Times filled in in Table 4: Operating and AC measurement conditions. 30-Nov-2007 3 Applied Numonyx branding. M36P0R9070E0 Please Read Carefully: INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH NUMONYXTM PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN NUMONYX'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NUMONYX ASSUMES NO LIABILITY WHATSOEVER, AND NUMONYX DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF NUMONYX PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. Numonyx products are not intended for use in medical, life saving, life sustaining, critical control or safety systems, or in nuclear facility applications. Numonyx may make changes to specifications and product descriptions at any time, without notice. Numonyx, B.V. may have patents or pending patent applications, trademarks, copyrights, or other intellectual property rights that relate to the presented subject matter. The furnishing of documents and other materials and information does not provide any license, express or implied, by estoppel or otherwise, to any such patents, trademarks, copyrights, or other intellectual property rights. Designers must not rely on the absence or characteristics of any features or instructions marked "reserved" or "undefined." Numonyx reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them. Contact your local Numonyx sales office or your distributor to obtain the latest specifications and before placing your product order. Copies of documents which have an order number and are referenced in this document, or other Numonyx literature may be obtained by visiting Numonyx's website at http://www.numonyx.com. Numonyx StrataFlash is a trademark or registered trademark of Numonyx or its subsidiaries in the United States and other countries. *Other names and brands may be claimed as the property of others. Copyright (c) 11/5/7, Numonyx, B.V., All Rights Reserved. 23/23