LSI21320RB - LSI Logic Corporation

DB11-000045-01

May 2003

Quick Hardware Setup Guide

LSI Logic LSI21320-R

Host Bus Adapter

Thank you for purchasing the LSI21320-R Host Bus Adapter (HBA).

Please take a few minutes to read this Quick Hardware Setup

Guide before you install the LSI21320-R. If you need more

information about any topic covered in this guide, please refer to

the other documents on the accompanying LSI Logic Host Bus

Adapter compact disk (CD).

Contents of the LSI Logic Host Bus Adapter CD

The LSI Logic Host Bus Adapter CD contains utility programs,

device drivers for various operating systems, and the following

documentation:

•LSI Logic Ultra320 SCSI to PCI-X Storage Adapter User’s Guide

•LSI Logic Device Management User’s Guide

•LSI Logic Host Bus Adapter technical product briefs

•Information on SCSI cables

Technical Support

For assistance installing, conﬁguring, or running the LSI21320-R,

contact LSI Logic Technical Support:

Phone Support: 1-800-633-4545

Web Site: http://www.lsilogic.com

Storage Adapter Installation

Caution: Make a backup of your data before changing your system

conﬁguration.

These steps install the LSI21320-R. The following text provides an

explanation of each step.

Step 1: Unpack Storage Adapter

Unpack the LSI21320-R in a static-free environment. Remove the

LSI21320-R from the antistatic bag and inspect it for damage. If it

appears to be damaged, or if the LSI Logic Host Bus Adapter CD

is missing, contact LSI Logic or your OEM support representative.

Step 2: Prepare Computer

Turn off the computer and remove the power cord from the back of

the power supply. Remove the cover from the chassis. Be certain

to disconnect the computer from the power and from any networks

before installing the controller card.

Step 3: Install LSI21320-R

Install the LSI21320-R in a 3.3 V or 5 V PCI slot, as shown in

Figure 2. Press down gently, but ﬁrmly, to seat the card properly the

slot. The bottom edge of the controller card must be ﬂush with the

slot. Then attach the LSI21320-R to the computer chassis with the

bracket screw. The LSI Logic Ultra320 SCSI to PCI-X Storage

Adapter User’s Guide provides detailed instructions for installing

and conﬁguring the LSI21320-R.

Step 4: Connect the SCSI Devices to the LSI21320-R

Connect SCSI devices to the internal high-density 68-pin SCSI

connectors and/or the external high-density 68-pin SCSI

connectors. To achieve maximum data throughput, use only

Ultra320 SCSI devices. The LSI21320-R supports up to 15 Ultra320

SCSI devices per channel and a maximum SCSI bus cable length

of 12 m.

Disable SCSI termination on all the devices that are not located at

the end of the SCSI bus. Use only high-quality ribbon SCSI cables

for internal devices and high-quality round SCSI cables for external

devices. If you are connecting both SCSI disk drives and other

kinds of SCSI devices, LSI Logic recommends that you connect the

disk drives on one SCSI channel and the other devices on the other

channel. Figure 1 and the following table provide the location and

deﬁnition of the connectors on the LSI21320-R.

Figure 1 LSI21320-R Host Bus Adapter Board Drawing

Step Action

1 Unpack the LSI21320-R.

2 Turn off the computer, remove the power cord, and remove the cover.

3 Install the LSI21320-R in a PCI or PCI-X slot.

4 Connect the SCSI devices to the LSI21320-R.

5 Set the target IDs for the SCSI devices.

6 Set the SCSI termination.

7 Replace the computer cover and turn the power on.

8 Run the LSI Logic BIOS Conﬁguration Utility.

9 Install the operating system device driver.

Connector Deﬁnition

J1 PCI/PCI-X Connector

J2 External SCSI Channel A Connector

J3 Internal SCSI Channel B Connector

J1 - PCI/PCI-X

LSI53C1030

Channel A

Ultra320 SCSI LVD/SE

Channel B

Ultra320 SCSI LVD/SE

J6 for

Channels

A and B

Channel A

Ultra320 SCSI LVD/SE

Quick Hardware Setup Guide

DB11-000045-01, May 2003

LSI Logic, the LSI Logic logo design, Integrated Mirroring, and Integrated Striping are

trademarks or registered trademarks of LSI Logic Corporation. All other brand and prod-

uct names may be trademarks of their respective companies.

You can ﬁnd a list of LSI Logic Corporation’s U.S. distributors, international distributors,

sales ofﬁces, and design resource centers on the LSI Logic web site at:

http://www.lsilogic.com/contacts/index.html

LSI Logic Corporation reserves the right to make changes to any products and services

herein at any time without notice. LSI Logic does not assume any responsibility or liabil-

ity arising out of the application or use of any product or service described herein,

except as expressly agreed to in writing by LSI Logic; nor does the purchase, lease, or

use of a product or service from LSI Logic convey a license under any patent rights,

copyrights, trademark rights, or any other of the intellectual property rights of LSI Logic

or of third parties.

Step 5: Set Target IDs for SCSI Devices

Each connected SCSI device must have a unique Target ID (TID),

ranging from 0 to 15 for 16-bit devices. The LSI21320-R uses

TID 7, which is the highest priority TID. Verify that no two SCSI

devices on the same channel use the same TID; change the TIDs

as needed. See the SCSI device documentation for instructions

concerning changing the SCSI device’s TID.

Figure 2 Inserting the Host Bus Adapter Board

Step 6: Set SCSI Termination

The SCSI bus, which consists of the SCSI bus cables and SCSI

devices, is an electrical transmission line that must be terminated

properly to minimize signal reﬂections and prevent data loss.

Enable SCSI termination at each end of each SCSI bus (channel)

and only at the ends of the SCSI bus. In Figure 3, internal SCSI

devices connect to one channel. The LSI21320-R automatically

terminates its end of the SCSI bus if only internal devices or only

external devices connect to that channel. The LSI21320-R

automatically disables termination if both internal and external

devices connect to that channel, because the LSI21320-R is then

in the “middle” of the SCSI bus.

Figure 3 SCSI Termination for Internal SCSI Devices

For a disk array, set the SCSI bus termination so that removing or

adding a SCSI device does not disturb termination. To do this,

connect the LSI21320-R to one end of the SCSI cable and connect

a SCSI terminator module at the other end of the cable. Attach

SCSI devices to the connectors between the two ends and disable

termination on them. Figure 4 shows an external drive enclosure

with seven SCSI drives. Termination is enabled at the end of the

cable nearest the “last” SCSI drive, which is assigned TID 6.

Figure 4 SCSI Termination in a SCSI Disk Array

Some disk enclosures handle termination for the SCSI devices

within the enclosure. Refer to the enclosure documentation for

more information.

Step 7: Power Up the Computer

Replace the computer cover and connect the power cords. Turn on

the power to all the devices. Be sure the SCSI devices power up

before or at the same time as the computer. Otherwise, the

computer might not recognize the SCSI devices.

Step 8: Run the BIOS Conﬁguration Utility

During boot, the following message appears:

Press <Ctrl-C> to start the LSI Logic Configuration Utility

When this message appears, press <Ctrl-C> to run the LSI Logic

BIOS Conﬁguration Utility. The Fusion-MPT Device Management

User’s Guide provides instructions for using the LSI Logic BIOS

Conﬁguration Utility.

Step 9: Install the Operating System Driver

LSI Logic provides device drivers for the following operating

systems:

•MS-DOS version 6.xx or later

•Microsoft Windows NT 4.0, Windows 2000, Windows XP, and

Windows Server 2003

•Novell NetWare 5.1 and 6.0

•Red Hat Linux 7.2 and 7.3

Integrated RAID

The LSI21320-R supports integrated RAID, which includes

Integrated Mirroring™ (IM) and Integrated Striping™ (IS). IM

enables mirroring of two to six drives in a disk array. IS enables

data striping across up to six drives.

J4 Internal SCSI Channel A Connector

J6 LED for SCSI Channel A and SCSI Channel B1

1. If the LED does not light during SCSI bus activity, disconnect the LED cable,

rotate it 180 degrees, and re-connect the LED cable to J6.

Connector Deﬁnition

32-Bit Slots

64-Bit Slots

Bracket Screw

Termination on Controller

Enabled SCSI Devices

(Termination Disabled on Both)

SCSI

Terminator

TID 0

TID 1

TID 2

TID 3

TID 4

TID 5

TID 6

External

SCSI Drives

Termination

Enabled

LSI21320-R

TID 7

LSI53C1030