LM3249TLX-C/NOPB - Texas Instruments

LM124-N, LM224-N, LM2902-N, LM324-N

www.ti.com

SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004

LM124/LM224/LM324/LM2902 Low Power Quad Operational Amplifiers

Check for Samples: LM124-N,LM224-N,LM2902-N,LM324-N

1FEATURES

2• Internally frequency compensated for unity • Low input biasing current 45 nA

gain – (temperature compensated)

• Large DC voltage gain 100 dB • Low input offset voltage 2 mV

• Wide bandwidth (unity gain) 1 MHz – and offset current: 5 nA

– (temperature compensated) • Input common-mode voltage range includes

• Wide power supply range: ground

– Single supply 3V to 32V • Differential input voltage range equal to the

power supply voltage

– or dual supplies ±1.5V to ±16V • Large output voltage swing 0V to V+−1.5V

• Very low supply current drain (700

μA)—essentially independent of supply

voltage

DESCRIPTION

The LM124 series consists of four independent, high gain, internally frequency compensated operational

amplifiers which were designed specifically to operate from a single power supply over a wide range of voltages.

Operation from split power supplies is also possible and the low power supply current drain is independent of the

magnitude of the power supply voltage.

Application areas include transducer amplifiers, DC gain blocks and all the conventional op amp circuits which

now can be more easily implemented in single power supply systems. For example, the LM124 series can be

directly operated off of the standard +5V power supply voltage which is used in digital systems and will easily

provide the required interface electronics without requiring the additional ±15V power supplies.

UNIQUE CHARACTERISTICS

• In the linear mode the input common-mode voltage range includes ground and the output voltage can also

swing to ground, even though operated from only a single power supply voltage

• The unity gain cross frequency is temperature compensated

• The input bias current is also temperature compensated

ADVANTAGES

• Eliminates need for dual supplies

• Four internally compensated op amps in a single package

• Allows directly sensing near GND and VOUT also goes to GND

• Compatible with all forms of logic

• Power drain suitable for battery operation

1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

2All trademarks are the property of their respective owners.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

LM124-N, LM224-N, LM2902-N, LM324-N

SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004

www.ti.com

CONNECTION DIAGRAM

LM124A available per JM38510/11006

LM124 available per JM38510/11005

See STD Mil DWG 5962R99504 for Radiation Tolerant Device

Figure 1. Dual-In-Line Package Top View

SCHEMATIC DIAGRAM

(Each Amplifier)

These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam

during storage or handling to prevent electrostatic damage to the MOS gates.

Product Folder Links: LM124-N LM224-N LM2902-N LM324-N

LM124-N, LM224-N, LM2902-N, LM324-N

www.ti.com

SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004

ABSOLUTE MAXIMUM RATINGS(1)

LM124/LM224/LM324 LM2902

LM124A/LM224A/LM324A

Supply Voltage, V+32V 26V

Differential Input Voltage 32V 26V

Input Voltage −0.3V to +32V −0.3V to +26V

Input Current

(VIN <−0.3V) (2) 50 mA 50 mA

Power Dissipation (3)

Molded DIP 1130 mW 1130 mW

Cavity DIP 1260 mW 1260 mW

Small Outline Package 800 mW 800 mW

Output Short-Circuit to GND

(One Amplifier) (4)

V+≤15V and TA= 25°C Continuous Continuous

Operating Temperature Range −40°C to +85°C

LM324/LM324A 0°C to +70°C

LM224/LM224A −25°C to +85°C

LM124/LM124A −55°C to +125°C

Storage Temperature Range −65°C to +150°C −65°C to +150°C

Lead Temperature (Soldering, 10 seconds) 260°C 260°C

Soldering Information

Dual-In-Line Package

Soldering (10 seconds) 260°C 260°C

Small Outline Package

Vapor Phase (60 seconds) 215°C 215°C

Infrared (15 seconds) 220°C 220°C

See AN-450 “Surface Mounting Methods and Their Effect on Product Reliability” for other methods of soldering surface mount devices.

ESD Tolerance (5) 250V 250V

(1) Refer to RETS124AX for LM124A military specifications and refer to RETS124X for LM124 military specifications.

(2) This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of

the input PNP transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is

also lateral NPN parasitic transistor action on the IC chip. This transistor action can cause the output voltages of the op amps to go to

the V+voltage level (or to ground for a large overdrive) for the time duration that an input is driven negative. This is not destructive and

normal output states will re-establish when the input voltage, which was negative, again returns to a value greater than −0.3V (at 25°C).

(3) For operating at high temperatures, the LM324/LM324A/LM2902 must be derated based on a +125°C maximum junction temperature

and a thermal resistance of 88°C/W which applies for the device soldered in a printed circuit board, operating in a still air ambient. The

LM224/LM224A and LM124/LM124A can be derated based on a +150°C maximum junction temperature. The dissipation is the total of

all four amplifiers—use external resistors, where possible, to allow the amplifier to saturate of to reduce the power which is dissipated in

the integrated circuit.

(4) Short circuits from the output to V+can cause excessive heating and eventual destruction. When considering short circuits to ground,

the maximum output current is approximately 40 mA independent of the magnitude of V+. At values of supply voltage in excess of +15V,

continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. Destructive dissipation can result

from simultaneous shorts on all amplifiers.

(5) Human body model, 1.5 kΩin series with 100 pF.

Product Folder Links: LM124-N LM224-N LM2902-N LM324-N

LM124-N, LM224-N, LM2902-N, LM324-N

SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004

www.ti.com

ELECTRICAL CHARACTERISTICS

V+= +5.0V, (1), unless otherwise stated LM124A LM224A LM324A Unit

Parameter Conditions s

Min Typ Max Min Typ Max Min Typ Max

Input Offset Voltage (2)TA= 25°C 1 2 1 3 2 3 mV

Input Bias Current IIN(+) or IIN(−), VCM = 0V, 20 50 40 80 45 100 nA

(3) TA= 25°C

Input Offset Current IIN(+) or IIN(−), VCM = 0V, 2 10 2 15 5 30 nA

TA= 25°C

Input Common-Mode V+= 30V, (LM2902, V+= 26V), 0 V+−1 V+−1 V+−1

0 0 V

.5 .5 .5

Voltage Range (4) TA= 25°C

Supply Current Over Full Temperature Range

RL=∞On All Op Amps mA

V+= 30V (LM2902 V+= 26V) 1.5 3 1.5 3 1.5 3

V+= 5V 0.7 1.2 0.7 1.2 0.7 1.2

Large Signal V+= 15V, RL≥2kΩ, V/m

50 100 50 100 25 100 V

Voltage Gain (VO= 1V to 11V), TA= 25°C

Common-Mode DC, VCM = 0V to V+−1.5V, 70 85 70 85 65 85 dB

Rejection Ratio TA= 25°C

Power Supply V+= 5V to 30V

Rejection Ratio (LM2902, V+= 5V to 26V), 65 100 65 100 65 100 dB

TA= 25°C

Amplifier-to-Amplifier f = 1 kHz to 20 kHz, TA= 25°C −120 −120 −120 dB

Coupling (5) (Input Referred)

Output Current Source VIN+= 1V, VIN−= 0V, 20 40 20 40 20 40

V+= 15V, VO= 2V, TA= 25°C mA

Sink VIN−= 1V, VIN+= 0V, 10 20 10 20 10 20

V+= 15V, VO= 2V, TA= 25°C

VIN−= 1V, VIN+= 0V, 12 50 12 50 12 50 μA

V+= 15V, VO= 200 mV, TA= 25°C

Short Circuit to Ground (6)V+= 15V, TA= 25°C 40 60 40 60 40 60 mA

Input Offset Voltage (2) 4 4 5 mV

VOS Drift RS= 0Ω μV/°

7 20 7 20 7 30 C

Input Offset Current IIN(+) −IIN(−), VCM = 0V 30 30 75 nA

IOS Drift RS= 0ΩpA/°

10 200 10 200 10 300 C

(1) These specifications are limited to −55°C ≤TA≤+125°C for the LM124/LM124A. With the LM224/LM224A, all temperature

specifications are limited to −25°C ≤TA≤+85°C, the LM324/LM324A temperature specifications are limited to 0°C ≤TA≤+70°C, and

the LM2902 specifications are limited to −40°C ≤TA≤+85°C.

(2) VO≃1.4V, RS= 0Ωwith V+from 5V to 30V; and over the full input common-mode range (0V to V+−1.5V) for LM2902, V+from 5V to

26V.

(3) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the

state of the output so no loading change exists on the input lines.

(4) The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25°C). The

upper end of the common-mode voltage range is V+−1.5V (at 25°C), but either or both inputs can go to +32V without damage (+26V

for LM2902), independent of the magnitude of V+.

(5) Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This

typically can be detected as this type of capacitance increases at higher frequencies.

(6) Short circuits from the output to V+can cause excessive heating and eventual destruction. When considering short circuits to ground,

the maximum output current is approximately 40 mA independent of the magnitude of V+. At values of supply voltage in excess of +15V,

continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. Destructive dissipation can result

from simultaneous shorts on all amplifiers.

Product Folder Links: LM124-N LM224-N LM2902-N LM324-N

LM124-N, LM224-N, LM2902-N, LM324-N

www.ti.com

SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004

ELECTRICAL CHARACTERISTICS (continued)

V+= +5.0V, (1), unless otherwise stated LM124A LM224A LM324A Unit

Parameter Conditions s

Min Typ Max Min Typ Max Min Typ Max

Input Bias Current IIN(+) or IIN(−)40 100 40 100 40 200 nA

Input Common-Mode V+= +30V 0 V+−2 0 V+−2 0 V+−2 V

Voltage Range (4) (LM2902, V+= 26V)

Large Signal V+= +15V (VOSwing = 1V to 11V)

Voltage Gain RL≥2 kΩ25 25 15 V/m

Output Voltage VOH V+= 30V RL= 2 kΩ26 26 26 V

Swing (LM2902, V+= 26V) RL= 10 kΩ27 28 27 28 27 28

VOL V+= 5V, RL= 10 kΩ5 20 5 20 5 20 mV

Output Current Source VO= 2V VIN+= +1V, 10 20 10 20 10 20

VIN−= 0V, mA

V+= 15V

Sink VIN−= +1V, 10 15 5 8 5 8

VIN+= 0V,

V+= 15V

Product Folder Links: LM124-N LM224-N LM2902-N LM324-N

LM124-N, LM224-N, LM2902-N, LM324-N

SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004

www.ti.com

ELECTRICAL CHARACTERISTICS

V+= +5.0V, (1), unless otherwise stated LM124/LM224 LM324 LM2902 Unit

Parameter Conditions s

Min Typ Max Min Typ Max Min Typ Max

Input Offset Voltage (2)TA= 25°C 2 5 2 7 2 7 mV

Input Bias Current IIN(+) or IIN(−), VCM = 0V, 45 150 45 250 45 250 nA

(3) TA= 25°C

Input Offset Current IIN(+) or IIN(−), VCM = 0V, 3 30 5 50 5 50 nA

TA= 25°C

Input Common-Mode V+= 30V, (LM2902, V+= 26V), 0 V+−1 V+−1 V+−1

0 0 V

.5 .5 .5

Voltage Range (4) TA= 25°C

Supply Current Over Full Temperature Range

RL=∞On All Op Amps mA

V+= 30V (LM2902 V+= 26V) 1.5 3 1.5 3 1.5 3

V+= 5V 0.7 1.2 0.7 1.2 0.7 1.2

Large Signal V+= 15V, RL≥2kΩ, V/m

50 100 25 100 25 100 V

Voltage Gain (VO= 1V to 11V), TA= 25°C

Common-Mode DC, VCM = 0V to V+−1.5V, 70 85 65 85 50 70 dB

Rejection Ratio TA= 25°C

Power Supply V+= 5V to 30V

Rejection Ratio (LM2902, V+= 5V to 26V), 65 100 65 100 50 100 dB

TA= 25°C

Amplifier-to-Amplifier f = 1 kHz to 20 kHz, TA= 25°C −120 −120 −120 dB

Coupling (5) (Input Referred)

Output Current Source VIN+= 1V, VIN−= 0V, 20 40 20 40 20 40

V+= 15V, VO= 2V, TA= 25°C mA

Sink VIN−= 1V, VIN+= 0V, 10 20 10 20 10 20

V+= 15V, VO= 2V, TA= 25°C

VIN−= 1V, VIN+= 0V, 12 50 12 50 12 50 μA

V+= 15V, VO= 200 mV, TA= 25°C

Short Circuit to Ground (6)V+= 15V, TA= 25°C 40 60 40 60 40 60 mA

Input Offset Voltage (2) 7 9 10 mV

VOS Drift RS= 0Ω μV/°

7 7 7 C

Input Offset Current IIN(+) −IIN(−), VCM = 0V 100 150 45 200 nA

IOS Drift RS= 0ΩpA/°

10 10 10 C

(1) These specifications are limited to −55°C ≤TA≤+125°C for the LM124/LM124A. With the LM224/LM224A, all temperature

specifications are limited to −25°C ≤TA≤+85°C, the LM324/LM324A temperature specifications are limited to 0°C ≤TA≤+70°C, and

the LM2902 specifications are limited to −40°C ≤TA≤+85°C.

(2) VO≃1.4V, RS= 0Ωwith V+from 5V to 30V; and over the full input common-mode range (0V to V+−1.5V) for LM2902, V+from 5V to

26V.

(3) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the

state of the output so no loading change exists on the input lines.

(4) The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25°C). The

upper end of the common-mode voltage range is V+−1.5V (at 25°C), but either or both inputs can go to +32V without damage (+26V

for LM2902), independent of the magnitude of V+.

(5) Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This

typically can be detected as this type of capacitance increases at higher frequencies.

(6) Short circuits from the output to V+can cause excessive heating and eventual destruction. When considering short circuits to ground,

the maximum output current is approximately 40 mA independent of the magnitude of V+. At values of supply voltage in excess of +15V,

continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. Destructive dissipation can result

from simultaneous shorts on all amplifiers.

Product Folder Links: LM124-N LM224-N LM2902-N LM324-N

LM124-N, LM224-N, LM2902-N, LM324-N

www.ti.com

SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004

ELECTRICAL CHARACTERISTICS (continued)

V+= +5.0V, (1), unless otherwise stated LM124/LM224 LM324 LM2902 Unit

Parameter Conditions s

Min Typ Max Min Typ Max Min Typ Max

Input Bias Current IIN(+) or IIN(−)40 300 40 500 40 500 nA

Input Common-Mode V+= +30V 0 V+−2 0 V+−2 0 V+−2 V

Voltage Range (4) (LM2902, V+= 26V)

Large Signal V+= +15V (VOSwing = 1V to 11V)

Voltage Gain RL≥2 kΩ25 15 15 V/m

Output Voltage VOH V+= 30V RL= 2 kΩ26 26 22 V

Swing (LM2902, V+= 26V) RL= 10 kΩ27 28 27 28 23 24

VOL V+= 5V, RL= 10 kΩ5 20 5 20 5 100 mV

Output Current Source VO= 2V VIN+= +1V, 10 20 10 20 10 20

VIN−= 0V, mA

V+= 15V

Sink VIN−= +1V, 5 8 5 8 5 8

VIN+= 0V,

V+= 15V

Product Folder Links: LM124-N LM224-N LM2902-N LM324-N

LM124-N, LM224-N, LM2902-N, LM324-N

SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004

www.ti.com

TYPICAL PERFORMANCE CHARACTERISTICS

Input Voltage Range Input Current

Supply Current Voltage Gain

Open Loop Frequency Common Mode Rejection

Response Ratio

Voltage Follower Pulse Voltage Follower Pulse

Response Response (Small Signal)

Large Signal Frequency Output Characteristics

Response Current Sourcing

Product Folder Links: LM124-N LM224-N LM2902-N LM324-N

LM124-N, LM224-N, LM2902-N, LM324-N

www.ti.com

SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004

TYPICAL PERFORMANCE CHARACTERISTICS (continued)

Output Characteristics

Current Sinking Current Limiting

Input Current (LM2902 only) Voltage Gain (LM2902 only)

APPLICATION HINTS

The LM124 series are op amps which operate with only a single power supply voltage, have true-differential

inputs, and remain in the linear mode with an input common-mode voltage of 0 VDC. These amplifiers operate

over a wide range of power supply voltage with little change in performance characteristics. At 25°C amplifier

operation is possible down to a minimum supply voltage of 2.3 VDC.

The pinouts of the package have been designed to simplify PC board layouts. Inverting inputs are adjacent to

outputs for all of the amplifiers and the outputs have also been placed at the corners of the package (pins 1, 7, 8,

and 14).

Precautions should be taken to insure that the power supply for the integrated circuit never becomes reversed in

polarity or that the unit is not inadvertently installed backwards in a test socket as an unlimited current surge

through the resulting forward diode within the IC could cause fusing of the internal conductors and result in a

destroyed unit.

Large differential input voltages can be easily accommodated and, as input differential voltage protection diodes

are not needed, no large input currents result from large differential input voltages. The differential input voltage

may be larger than V+without damaging the device. Protection should be provided to prevent the input voltages

from going negative more than −0.3 VDC (at 25°C). An input clamp diode with a resistor to the IC input terminal

can be used.

To reduce the power supply drain, the amplifiers have a class A output stage for small signal levels which

converts to class B in a large signal mode. This allows the amplifiers to both source and sink large output

currents. Therefore both NPN and PNP external current boost transistors can be used to extend the power

capability of the basic amplifiers. The output voltage needs to raise approximately 1 diode drop above ground to

bias the on-chip vertical PNP transistor for output current sinking applications.

For ac applications, where the load is capacitively coupled to the output of the amplifier, a resistor should be

used, from the output of the amplifier to ground to increase the class A bias current and prevent crossover

distortion.

Where the load is directly coupled, as in dc applications, there is no crossover distortion.

Capacitive loads which are applied directly to the output of the amplifier reduce the loop stability margin. Values

of 50 pF can be accommodated using the worst-case non-inverting unity gain connection. Large closed loop

gains or resistive isolation should be used if larger load capacitance must be driven by the amplifier.

Product Folder Links: LM124-N LM224-N LM2902-N LM324-N

LM124-N, LM224-N, LM2902-N, LM324-N

SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004

www.ti.com

The bias network of the LM124 establishes a drain current which is independent of the magnitude of the power

supply voltage over the range of from 3 VDC to 30 VDC.

Output short circuits either to ground or to the positive power supply should be of short time duration. Units can

be destroyed, not as a result of the short circuit current causing metal fusing, but rather due to the large increase

in IC chip dissipation which will cause eventual failure due to excessive junction temperatures. Putting direct

short-circuits on more than one amplifier at a time will increase the total IC power dissipation to destructive

levels, if not properly protected with external dissipation limiting resistors in series with the output leads of the

amplifiers. The larger value of output source current which is available at 25°C provides a larger output current

capability at elevated temperatures (see typical performance characteristics) than a standard IC op amp.

The circuits presented in the section on typical applications emphasize operation on only a single power supply

voltage. If complementary power supplies are available, all of the standard op amp circuits can be used. In

general, introducing a pseudo-ground (a bias voltage reference of V+/2) will allow operation above and below this

value in single power supply systems. Many application circuits are shown which take advantage of the wide

input common-mode voltage range which includes ground. In most cases, input biasing is not required and input

voltages which range to ground can easily be accommodated.

TYPICAL SINGLE-SUPPLY APPLICATIONS

(V+= 5.0 VDC)

*R not needed due to temperature independent IIN

Figure 2. Non-Inverting DC Gain (0V Input = 0V Output)

Where: V0= V1+ V2−V3−V4

(V1+ V2)≥(V3+ V4) to keep VO> 0 VDC

Figure 3. DC Summing Amplifier

(VIN'S ≥0 VDC and VO≥VDC)

Product Folder Links: LM124-N LM224-N LM2902-N LM324-N

LM124-N, LM224-N, LM2902-N, LM324-N

www.ti.com

SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004

(V+= 5.0 VDC)

V0= 0 VDC for VIN = 0 VDC

AV= 10

Figure 4. Power Amplifier

Figure 5. LED Driver

fo= 1 kHz

Q = 50

AV= 100 (40 dB)

Figure 6. “BI-QUAD” RC Active Bandpass Filter

Product Folder Links: LM124-N LM224-N LM2902-N LM324-N

LM124-N, LM224-N, LM2902-N, LM324-N

SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004

www.ti.com

(V+= 5.0 VDC)

Figure 7. Fixed Current Sources

Figure 8. Lamp Driver

*(Increase R1 for ILsmall)

Figure 9. Current Monitor

Product Folder Links: LM124-N LM224-N LM2902-N LM324-N

LM124-N, LM224-N, LM2902-N, LM324-N

www.ti.com

SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004

(V+= 5.0 VDC)

Figure 10. Driving TTL

Figure 11. Voltage Follower

Figure 12.

Figure 13. Pulse Generator

Figure 14. Squarewave Oscillator

Product Folder Links: LM124-N LM224-N LM2902-N LM324-N

LM124-N, LM224-N, LM2902-N, LM324-N

SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004

www.ti.com

(V+= 5.0 VDC)

Figure 15. Pulse Generator

IO= 1 amp/volt VIN

(Increase REfor Iosmall)

Figure 16. High Compliance Current Sink

Figure 17. Low Drift Peak Detector

Product Folder Links: LM124-N LM224-N LM2902-N LM324-N

LM124-N, LM224-N, LM2902-N, LM324-N

www.ti.com

SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004

(V+= 5.0 VDC)

Figure 18. Comparator with Hysteresis

VO= VR

Figure 19. Ground Referencing a Differential Input Signal

*Wide control voltage range: 0 VDC ≤VC≤2 (V+−1.5 VDC)

Figure 20. Voltage Controlled Oscillator Circuit

Figure 21. Photo Voltaic-Cell Amplifier

Product Folder Links: LM124-N LM224-N LM2902-N LM324-N

LM124-N, LM224-N, LM2902-N, LM324-N

SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004

www.ti.com

(V+= 5.0 VDC)

Figure 22. AC Coupled Inverting Amplifier

Figure 23. AC Coupled Non-Inverting Amplifier

Product Folder Links: LM124-N LM224-N LM2902-N LM324-N

LM124-N, LM224-N, LM2902-N, LM324-N

www.ti.com

SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004

(V+= 5.0 VDC)

fO= 1 kHz

Q = 1

AV= 2

Figure 24. DC Coupled Low-Pass RC Active Filter

Figure 25. High Input Z, DC Differential Amplifier

Product Folder Links: LM124-N LM224-N LM2902-N LM324-N

LM124-N, LM224-N, LM2902-N, LM324-N

SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004

www.ti.com

(V+= 5.0 VDC)

Figure 26. High Input Z Adjustable-Gain DC Instrumentation Amplifier

Figure 27. Using Symmetrical Amplifiers to Reduce Input Current (General Concept)

Product Folder Links: LM124-N LM224-N LM2902-N LM324-N

LM124-N, LM224-N, LM2902-N, LM324-N

www.ti.com

SNOSC16B –MAY 2004–REVISED SEPTEMBER 2004

(V+= 5.0 VDC)

Figure 28. Bridge Current Amplifier

fO= 1 kHz

Q = 25

Figure 29. Bandpass Active Filter

Product Folder Links: LM124-N LM224-N LM2902-N LM324-N

PACKAGE OPTION ADDENDUM

www.ti.com 12-Nov-2012

Addendum-Page 1

PACKAGING INFORMATION

Orderable Device Status

(1)

Package Type Package

Drawing Pins Package Qty Eco Plan

(2)

Lead/Ball Finish MSL Peak Temp

(3)

Samples

(Requires Login)

LM124AJ/PB ACTIVE CDIP J 14 25 TBD A42 SNPB Level-1-NA-UNLIM

LM124J/PB ACTIVE CDIP J 14 25 TBD A42 SNPB Level-1-NA-UNLIM

LM224J ACTIVE CDIP J 14 25 TBD A42 SNPB Level-1-NA-UNLIM

LM2902M ACTIVE SOIC D 14 55 TBD CU SNPB Level-1-235C-UNLIM

LM2902M/NOPB ACTIVE SOIC D 14 55 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM

LM2902MT ACTIVE TSSOP PW 14 94 TBD CU SNPB Level-1-260C-UNLIM

LM2902MT/NOPB ACTIVE TSSOP PW 14 94 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM

LM2902MTX ACTIVE TSSOP PW 14 2500 TBD CU SNPB Level-1-260C-UNLIM

LM2902MTX/NOPB ACTIVE TSSOP PW 14 2500 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM

LM2902MX ACTIVE SOIC D 14 2500 TBD CU SNPB Level-1-235C-UNLIM

LM2902MX/NOPB ACTIVE SOIC D 14 2500 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM

LM2902N/NOPB ACTIVE PDIP NFF 14 25 Green (RoHS

& no Sb/Br) CU SN Level-1-NA-UNLIM

LM2902N/PB ACTIVE PDIP NFF 14 25 TBD CU SNPB Level-1-NA-UNLIM

LM324AM ACTIVE SOIC D 14 55 TBD CU SNPB Level-1-235C-UNLIM

LM324AM/NOPB ACTIVE SOIC D 14 55 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM

LM324AMX ACTIVE SOIC D 14 2500 TBD CU SNPB Level-1-235C-UNLIM

LM324AMX/NOPB ACTIVE SOIC D 14 2500 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM

LM324AN/NOPB ACTIVE PDIP NFF 14 25 Green (RoHS

& no Sb/Br) CU SN Level-1-NA-UNLIM

LM324AN/PB ACTIVE PDIP NFF 14 25 TBD Call TI Level-1-NA-UNLIM

LM324J ACTIVE CDIP J 14 25 TBD A42 SNPB Level-1-NA-UNLIM

LM324M ACTIVE SOIC D 14 55 TBD CU SNPB Level-1-235C-UNLIM

LM324M/NOPB ACTIVE SOIC D 14 55 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM

LM324MT ACTIVE TSSOP PW 14 94 TBD CU SNPB Level-1-260C-UNLIM

PACKAGE OPTION ADDENDUM

www.ti.com 12-Nov-2012

Addendum-Page 2

Orderable Device Status

(1)

Package Type Package

Drawing Pins Package Qty Eco Plan

(2)

Lead/Ball Finish MSL Peak Temp

(3)

Samples

(Requires Login)

LM324MT/NOPB ACTIVE TSSOP PW 14 94 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM

LM324MTX ACTIVE TSSOP PW 14 2500 TBD CU SNPB Level-1-260C-UNLIM

LM324MTX/NOPB ACTIVE TSSOP PW 14 2500 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM

LM324MX ACTIVE SOIC D 14 2500 TBD CU SNPB Level-1-235C-UNLIM

LM324MX/NOPB ACTIVE SOIC D 14 2500 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM

LM324N/NOPB ACTIVE PDIP NFF 14 25 Green (RoHS

& no Sb/Br) Call TI Level-1-NA-UNLIM

LM324N/PB ACTIVE PDIP NFF 14 25 TBD Call TI Level-1-NA-UNLIM

MLM324P ACTIVE PDIP NFF 14 25 TBD Call TI Level-1-NA-UNLIM

(1) The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability

information and additional product content details.

TBD: The Pb-Free/Green conversion plan has not been defined.

Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that

lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.

Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between

the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.

Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight

in homogeneous material)

(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information

provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and

continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.

TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

PACKAGE OPTION ADDENDUM

www.ti.com 12-Nov-2012

Addendum-Page 3

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package

Type Package

Drawing Pins SPQ Reel

Diameter

(mm)

Reel

Width

W1 (mm)

(mm) B0

(mm) K0

(mm) P1

(mm) W

(mm) Pin1

Quadrant

LM2902MTX TSSOP PW 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1

LM2902MTX/NOPB TSSOP PW 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1

LM2902MX SOIC D 14 2500 330.0 16.4 6.5 9.35 2.3 8.0 16.0 Q1

LM2902MX/NOPB SOIC D 14 2500 330.0 16.4 6.5 9.35 2.3 8.0 16.0 Q1

LM324AMX SOIC D 14 2500 330.0 16.4 6.5 9.35 2.3 8.0 16.0 Q1

LM324AMX/NOPB SOIC D 14 2500 330.0 16.4 6.5 9.35 2.3 8.0 16.0 Q1

LM324MTX TSSOP PW 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1

LM324MTX/NOPB TSSOP PW 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1

LM324MX SOIC D 14 2500 330.0 16.4 6.5 9.35 2.3 8.0 16.0 Q1

LM324MX/NOPB SOIC D 14 2500 330.0 16.4 6.5 9.35 2.3 8.0 16.0 Q1

PACKAGE MATERIALS INFORMATION

www.ti.com 15-Nov-2012

Pack Materials-Page 1

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)

LM2902MTX TSSOP PW 14 2500 349.0 337.0 45.0

LM2902MTX/NOPB TSSOP PW 14 2500 349.0 337.0 45.0

LM2902MX SOIC D 14 2500 349.0 337.0 45.0

LM2902MX/NOPB SOIC D 14 2500 349.0 337.0 45.0

LM324AMX SOIC D 14 2500 349.0 337.0 45.0

LM324AMX/NOPB SOIC D 14 2500 349.0 337.0 45.0

LM324MTX TSSOP PW 14 2500 349.0 337.0 45.0

LM324MTX/NOPB TSSOP PW 14 2500 349.0 337.0 45.0

LM324MX SOIC D 14 2500 349.0 337.0 45.0

LM324MX/NOPB SOIC D 14 2500 349.0 337.0 45.0

PACKAGE MATERIALS INFORMATION

www.ti.com 15-Nov-2012

Pack Materials-Page 2

MECHANICAL DATA

N0014A

www.ti.com

N14A (Rev G)

NFF0014A

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other

changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest

issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and

complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale

supplied at the time of order acknowledgment.

TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms

and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary

to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily

performed.

TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and

applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or

other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information

published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or

endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the

third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration

and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered

documentation. Information of third parties may be subject to additional restrictions.

Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service

voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.

TI is not responsible or liable for any such statements.

Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements

concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support

that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which

anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause

harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use

of any TI components in safety-critical applications.

In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to

help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and

requirements. Nonetheless, such components are subject to these terms.

No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties

have executed a special agreement specifically governing such use.

Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in

military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components

which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and

regulatory requirements in connection with such use.

TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of

non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.

Products Applications

Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive

Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications

Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers

DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps

DSP dsp.ti.com Energy and Lighting www.ti.com/energy

Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial

Interface interface.ti.com Medical www.ti.com/medical

Logic logic.ti.com Security www.ti.com/security

Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense

Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video

RFID www.ti-rfid.com

OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com

Wireless Connectivity www.ti.com/wirelessconnectivity

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Texas Instruments:

LM3249TLE-C/NOPB LM3249TLX-C/NOPB