LMS33460
LMS33460 3V Under Voltage Detector
Literature Number: SNVS158C
LMS33460
February 11, 2011
3V Under Voltage Detector
General Description
The LMS33460 is an under voltage detector with a 3.0V
threshold and extremely low power consumption. The
LMS33460 is specifically designed to accurately monitor pow-
er supplies. It is especially suited to battery powered systems
where low quiescent current and small size are required. This
IC generates an active output whenever the input voltage
drops below 3.0 Volts.
This part uses a precision on-chip voltage reference and a
comparator to measure the input voltage. Built in hysteresis
helps to prevent erratic operation in the presence of noise.
The UVD is available in the ultra-miniature SC70-5 package.
Features
Ultra low Power
3.0V detection
VIN Range: 0.8V to 7.0V
Open drain output
Ultra-small SC70-5 package
Extended Temperature range (−40°C to 85°C)
Ultra Low Quiescent current (1µA typ)
Applications
Low battery voltage detector
Power Fail Indicator
Processor Reset Generator
Battery Backup Control
Battery Operated Equipment
Hand-held Instruments
Typical Application
20020003
© 2011 National Semiconductor Corporation 200200 www.national.com
LMS33460 3V Under Voltage Detector
Connection Diagram
SC70-5
20020002
Top View
Ordering Information
Package Part Number Package Marking Transport Media NSC
Drawing
5-Pin SC70-5 LMS33460MG C33 1k Units Tape and Reel MAA05A
LMS33460MGX 3k Units Tape and Reel
For LMS33460 Ordering and Availability Information see: http://www.national.com/mpf/LM/LMS33460.html#Order
Block Diagram
20020001
www.national.com 2
LMS33460
Absolute Maximum Ratings (Note 1)
Input Voltage to GND 8.0V
Output Voltage to GND 8.0V
Output Continuous Output Current 30mA
Vapor Phase IR Convection Reflow 240°C
ESD Rating (Note 4)
Human Body Model 2500V
Machine Model 200V
TJMAX (Note 3)150°C
θJA (Note 3)478°C/W
Temperature Range
Operating Junction −40°C to +85°C
Storage Temperature Range −65°C to +150°C
Electrical Characteristics
Unless otherwise specified, all limits guaranteed for TJ = 25°C. Boldface limits apply at the temperature extremes.
Symbol Parameter Conditions Min Typ Max Units
VDET Detector Threshold VIN Falling 2.85 3.0 3.15 V
VHYS Detector Voltage Hysteresis VIN Rising 0.095 0.155 0.215 V
IIN Input Supply Current
VIN = 2.87V 1.0 2.2 µA
VIN = 4.7V 1.2 3.6 µA
VIN = 7.0V (Note 3)25 200 µA
VIN(MAX) Maximum Operating Voltage 7.0 V
VIN(MIN)
Minimum Operating Voltage
(Note 2) 0.7
1.0
1.1
1.3 V
IOUT(LOW) Output Current Low VOUT = 0.05V, VIN = 1.1V
VOUT = 0.50V, VIN = 1.5V
0.01
2
0.6
11 mA
tPDHL
Output Delay Time
Output Transition
High to Low
CL = 10pF, RL = 470k
130 200 µsec
ΔVDETTDetect Voltage Temperature
Coefficient ±120 PPM/°C
Note 1: Absolute maximum ratings indicate limits beyond which damage to the device may occur. Electrical specifications do not apply when operating the device
beyond its rated operating conditions.
Note 2: Temperature range specifications is guaranteed by design.
Note 3: Quiescent current will increase substantially above 5.5 volts, but is very low in the normal range below 5.5 volts.
Note 4: Human Body Model (HBM): 1.5k in series with 100pF; Machine Model (MM): 0 in series with 200pF.
3 www.national.com
LMS33460
Typical Characteristics (TA = 25°C, RL = 470 k and CL = 10 pF unless otherwise noted).
Detector Threshold vs. Temperature
20020005
Supply Current vs. Input Voltage
20020004
Propagation Delay Time (tPDHL) vs. Temperature
20020006
Propagation Delay Time (tPDLH) vs. Temperature
20020007
VOUT(LOW) vs. VIN
20020010
www.national.com 4
LMS33460
Application Circuit Information
The LMS33460 is a micro power under voltage sensing circuit
with an open drain output configuration, which requires a pull
resistor.
The LMS33460 features a voltage reference, a comparator
with precise thresholds and built in hysteresis to prevent er-
ratic reset operation.
20020008
FIGURE 1. Propagation Delay Timing Diagram
20020009
FIGURE 2. Propagation Delay Test Circuit
5 www.national.com
LMS33460
Physical Dimensions inches (millimeters) unless otherwise noted
5-Pin SC70-5
NSC Package Number MAA05A
www.national.com 6
LMS33460
Notes
7 www.national.com
LMS33460
Notes
LMS33460 3V Under Voltage Detector
For more National Semiconductor product information and proven design tools, visit the following Web sites at:
www.national.com
Products Design Support
Amplifiers www.national.com/amplifiers WEBENCH® Tools www.national.com/webench
Audio www.national.com/audio App Notes www.national.com/appnotes
Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns
Data Converters www.national.com/adc Samples www.national.com/samples
Interface www.national.com/interface Eval Boards www.national.com/evalboards
LVDS www.national.com/lvds Packaging www.national.com/packaging
Power Management www.national.com/power Green Compliance www.national.com/quality/green
Switching Regulators www.national.com/switchers Distributors www.national.com/contacts
LDOs www.national.com/ldo Quality and Reliability www.national.com/quality
LED Lighting www.national.com/led Feedback/Support www.national.com/feedback
Voltage References www.national.com/vref Design Made Easy www.national.com/easy
PowerWise® Solutions www.national.com/powerwise Applications & Markets www.national.com/solutions
Serial Digital Interface (SDI) www.national.com/sdi Mil/Aero www.national.com/milaero
Temperature Sensors www.national.com/tempsensors SolarMagic™ www.national.com/solarmagic
PLL/VCO www.national.com/wireless PowerWise® Design
University
www.national.com/training
THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION
(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY
OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO
SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,
IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS
DOCUMENT.
TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT
NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL
PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR
APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND
APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE
NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.
EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO
LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE
AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR
PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY
RIGHT.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and
whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected
to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform
can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.
National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other
brand or product names may be trademarks or registered trademarks of their respective holders.
Copyright© 2011 National Semiconductor Corporation
For the most current product information visit us at www.national.com
National Semiconductor
Americas Technical
Support Center
Email: support@nsc.com
Tel: 1-800-272-9959
National Semiconductor Europe
Technical Support Center
Email: europe.support@nsc.com
National Semiconductor Asia
Pacific Technical Support Center
Email: ap.support@nsc.com
National Semiconductor Japan
Technical Support Center
Email: jpn.feedback@nsc.com
www.national.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TIs terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TIs standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Audio www.ti.com/audio Communications and Telecom www.ti.com/communications
Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers
Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps
DLP®Products www.dlp.com Energy and Lighting www.ti.com/energy
DSP dsp.ti.com Industrial www.ti.com/industrial
Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical
Interface interface.ti.com Security www.ti.com/security
Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright ©2011, Texas Instruments Incorporated