ADC0802 - National Semiconductor - Datasheet.Directory

TL/H/5671

ADC0801/ADC0802/ADC0803/ADC0804/ADC0805

8-Bit mP Compatible A/D Converters

December 1994

ADC0801/ADC0802/ADC0803/ADC0804/ADC0805

8-Bit mP Compatible A/D Converters

General Description

The ADC0801, ADC0802, ADC0803, ADC0804 and

ADC0805 are CMOS 8-bit successive approximation A/D

converters that use a differential potentiometric ladderÐ

similar to the 256R products. These converters are de-

signed to allow operation with the NSC800 and INS8080A

derivative control bus with TRI-STATEÉoutput latches di-

rectly driving the data bus. These A/Ds appear like memory

locations or I/O ports to the microprocessor and no inter-

facing logic is needed.

Differential analog voltage inputs allow increasing the com-

mon-mode rejection and offsetting the analog zero input

voltage value. In addition, the voltage reference input can

be adjusted to allow encoding any smaller analog voltage

span to the full 8 bits of resolution.

Features

YCompatible with 8080 mP derivativesÐno interfacing

logic needed - access time - 135 ns

YEasy interface to all microprocessors, or operates

‘‘stand alone’’

YDifferential analog voltage inputs

YLogic inputs and outputs meet both MOS and TTL volt-

age level specifications

YWorks with 2.5V (LM336) voltage reference

YOn-chip clock generator

Y0V to 5V analog input voltage range with single 5V

supply

YNo zero adjust required

Y0.3×standard width 20-pin DIP package

Y20-pin molded chip carrier or small outline package

YOperates ratiometrically or with 5 VDC, 2.5 VDC, or ana-

log span adjusted voltage reference

Key Specifications

YResolution 8 bits

YTotal error g(/4 LSB, g(/2 LSB and g1 LSB

YConversion time 100 ms

Typical Applications

TL/H/5671–1

8080 Interface

TL/H/5671–31

Error Specification (Includes Full-Scale,

Zero Error, and Non-Linearity)

Part Full- VREF/2e2.500 VDC VREF/2eNo Connection

Number Scale (No Adjustments) (No Adjustments)

Adjusted

ADC0801 g(/4 LSB

ADC0802 g(/2 LSB

ADC0803 g(/2 LSB

ADC0804 g1 LSB

ADC0805 g1 LSB

TRI-STATEÉis a registered trademark of National Semiconductor Corp.

Z-80Éis a registered trademark of Zilog Corp.

C1995 National Semiconductor Corporation RRD-B30M115/Printed in U. S. A.

Absolute Maximum Ratings (Notes1&2)

If Military/Aerospace specified devices are required,

please contact the National Semiconductor Sales

Office/Distributors for availability and specifications.

Supply Voltage (VCC) (Note 3) 6.5V

Voltage

Logic Control Inputs b0.3V to a18V

At Other Input and Outputs b0.3V to (VCCa0.3V)

Lead Temp. (Soldering, 10 seconds)

Dual-In-Line Package (plastic) 260§C

Dual-In-Line Package (ceramic) 300§C

Surface Mount Package

Vapor Phase (60 seconds) 215§C

Infrared (15 seconds) 220§C

Storage Temperature Range b65§Ctoa

150§C

Package Dissipation at TAe25§C 875 mW

ESD Susceptibility (Note 10) 800V

Operating Ratings (Notes1&2)

Temperature Range TMINsTAsTMAX

ADC0801/02LJ, ADC0802LJ/883 b55§CsTAsa125§C

ADC0801/02/03/04LCJ b40§CsTAsa85§C

ADC0801/02/03/05LCN b40§CsTAsa85§C

ADC0804LCN 0§CsTAsa70§C

ADC0802/03/04LCV 0§CsTAsa70§C

ADC0802/03/04LCWM 0§CsTAsa70§C

Range of VCC 4.5 VDC to 6.3 VDC

Electrical Characteristics

The following specifications apply for VCCe5V

DC,T

MINsTAsTMAX and fCLKe640 kHz unless otherwise specified.

Parameter Conditions Min Typ Max Units

ADC0801: Total Adjusted Error (Note 8) With Full-Scale Adj. g(/4 LSB

(See Section 2.5.2)

ADC0802: Total Unadjusted Error (Note 8) VREF/2e2.500 VDC g(/2 LSB

ADC0803: Total Adjusted Error (Note 8) With Full-Scale Adj. g(/2 LSB

(See Section 2.5.2)

ADC0804: Total Unadjusted Error (Note 8) VREF/2e2.500 VDC g1 LSB

ADC0805: Total Unadjusted Error (Note 8) VREF/2-No Connection g1 LSB

VREF/2 Input Resistance (Pin 9) ADC0801/02/03/05 2.5 8.0 kX

ADC0804 (Note 9) 0.75 1.1 kX

Analog Input Voltage Range (Note 4) V(a)orV(

) Gnd– 0.05 VCCa0.05 VDC

DC Common-Mode Error Over Analog Input Voltage g(/16 g(/8 LSB

Range

Power Supply Sensitivity VCCe5V

DC g10% Over g(/16 g(/8 LSB

Allowed VIN(a) and VIN(b)

Voltage Range (Note 4)

AC Electrical Characteristics

The following specifications apply for VCCe5V

DC and TAe25§C unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Units

TCConversion Time fCLKe640 kHz (Note 6) 103 114 ms

TCConversion Time (Note 5, 6) 66 73 1/fCLK

fCLK Clock Frequency VCCe5V, (Note 5) 100 640 1460 kHz

Clock Duty Cycle (Note 5) 40 60 %

CR Conversion Rate in Free-Running INTR tied to WR with 8770 9708 conv/s

Mode CSe0V

DC,f

CLKe640 kHz

tW(WR)L Width of WR Input (Start Pulse Width) CSe0V

DC (Note 7) 100 ns

tACC Access Time (Delay from Falling CLe100 pF 135 200 ns

Edge of RD to Output Data Valid)

t1H,t

0H TRI-STATE Control (Delay CLe10 pF, RLe10k 125 200 ns

from Rising Edge of RD to (See TRI-STATE Test

Hi-Z State) Circuits)

tWI,t

RI Delay from Falling Edge 300 450 ns

of WR or RD to Reset of INTR

CIN Input Capacitance of Logic 5 7.5 pF

Control Inputs

COUT TRI-STATE Output 5 7.5 pF

Capacitance (Data Buffers)

CONTROL INPUTS [Note: CLK IN (Pin 4) is the input of a Schmitt trigger circuit and is therefore specified separately]

VIN (1) Logical ‘‘1’’ Input Voltage VCCe5.25 VDC 2.0 15 VDC

(Except Pin 4 CLK IN)

AC Electrical Characteristics (Continued)

The following specifications apply for VCC e5VDC and TMIN sTAsTMAX, unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Units

CONTROL INPUTS [Note: CLK IN (Pin 4) is the input of a Schmitt trigger circuit and is therefore specified separately]

VIN (0) Logical ‘‘0’’ Input Voltage VCCe4.75 VDC 0.8 VDC

(Except Pin 4 CLK IN)

IIN (1) Logical ‘‘1’’ Input Current VINe5V

DC 0.005 1 mADC

(All Inputs)

IIN (0) Logical ‘‘0’’ Input Current VINe0V

DC b1b0.005 mADC

(All Inputs)

CLOCK IN AND CLOCK R

VTaCLK IN (Pin 4) Positive Going 2.7 3.1 3.5 VDC

Threshold Voltage

VTbCLK IN (Pin 4) Negative 1.5 1.8 2.1 VDC

Going Threshold Voltage

VHCLK IN (Pin 4) Hysteresis 0.6 1.3 2.0 VDC

(VTa)b(VTb)

VOUT (0) Logical ‘‘0’’ CLK R Output IOe360 mA 0.4 VDC

Voltage VCCe4.75 VDC

VOUT (1) Logical ‘‘1’’ CLK R Output IOeb360 mA 2.4 VDC

Voltage VCCe4.75 VDC

DATA OUTPUTS AND INTR

VOUT (0) Logical ‘‘0’’ Output Voltage

Data Outputs IOUTe1.6 mA, VCCe4.75 VDC 0.4 VDC

INTR Output IOUTe1.0 mA, VCCe4.75 VDC 0.4 VDC

VOUT (1) Logical ‘‘1’’ Output Voltage IOeb360 mA, VCCe4.75 VDC 2.4 VDC

VOUT (1) Logical ‘‘1’’ Output Voltage IOeb10 mA, VCCe4.75 VDC 4.5 VDC

IOUT TRI-STATE Disabled Output VOUTe0V

DC b3mADC

Leakage (All Data Buffers) VOUTe5V

DC 3mADC

ISOURCE VOUT Short to Gnd, TAe25§C 4.5 6 mADC

ISINK VOUT Short to VCC,T

25§C 9.0 16 mADC

POWER SUPPLY

ICC Supply Current (Includes fCLKe640 kHz,

Ladder Current) VREF/2eNC, TAe25§C

and CSe5V

ADC0801/02/03/04LCJ/05 1.1 1.8 mA

ADC0804LCN/LCV/LCWM 1.9 2.5 mA

Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating

the device beyond its specified operating conditions.

Note 2: All voltages are measured with respect to Gnd, unless otherwise specified. The separate A Gnd point should always be wired to the D Gnd.

Note 3: A zener diode exists, internally, from VCC to Gnd and has a typical breakdown voltage of 7 VDC.

Note 4: For VIN(b)tVIN(a) the digital output code will be 0000 0000. Two on-chip diodes are tied to each analog input (see block diagram) which will forward

conduct for analog input voltages one diode drop below ground or one diode drop greater than the VCC supply. Be careful, during testing at low VCC levels (4.5V),

as high level analog inputs (5V) can cause this input diode to conduct–especially at elevated temperatures, and cause errors for analog inputs near full-scale. The

spec allows 50 mV forward bias of either diode. This means that as long as the analog VIN does not exceed the supply voltage by more than 50 mV, the output

code will be correct. To achieve an absolute 0 VDC to5V

DC input voltage range will therefore require a minimum supply voltage of 4.950 VDC over temperature

variations, initial tolerance and loading.

Note 5: Accuracy is guaranteed at fCLK e640 kHz. At higher clock frequencies accuracy can degrade. For lower clock frequencies, the duty cycle limits can be

extended so long as the minimum clock high time interval or minimum clock low time interval is no less than 275 ns.

Note 6: With an asynchronous start pulse, up to 8 clock periods may be required before the internal clock phases are proper to start the conversion process. The

start request is internally latched, see

Figure 2

and section 2.0.

Note 7: The CS input is assumed to bracket the WR strobe input and therefore timing is dependent on the WR pulse width. An arbitrarily wide pulse width will hold

the converter in a reset mode and the start of conversion is initiated by the low to high transition of the WR pulse (see timing diagrams).

Note 8: None of these A/Ds requires a zero adjust (see section 2.5.1). To obtain zero code at other analog input voltages see section 2.5 and

Figure 5

Note 9: The VREF/2 pin is the center point of a two-resistor divider connected from VCC to ground. In all versions of the ADC0801, ADC0802, ADC0803, and

ADC0805, and in the ADC0804LCJ, each resistor is typically 16 kX. In all versions of the ADC0804 except the ADC0804LCJ, each resistor is typically 2.2 kX.

Note 10: Human body model, 100 pF discharged through a 1.5 kXresistor.

Typical Performance Characteristics

Logic Input Threshold Voltage

vs. Supply Voltage

Delay From Falling Edge of

RD to Output Data Valid

vs. Load Capacitance

CLK IN Schmitt Trip Levels

vs. Supply Voltage

fCLK vs. Clock Capacitor

Full-Scale Error vs

Conversion Time

Effect of Unadjusted Offset Error

vs. VREF/2 Voltage

Output Current vs

Temperature

Power Supply Current

vs Temperature (Note 9)

Linearity Error at Low

VREF/2 Voltages

TL/H/5671–2

TRI-STATE Test Circuits and Waveforms

t1H t1H,C

10 pF

tre20 ns

t0H t0H,C

10 pF

tre20 ns TL/H/5671–3

Timing Diagrams (All timing is measured from the 50% voltage points)

Output Enable and Reset INTR

Note: Read strobe must occur 8 clock periods (8/fCLK) after assertion of interrupt to guarantee reset of INTR. TL/H/5671–4

Typical Applications (Continued)

6800 Interface Ratiometric with Full-Scale Adjust

Note: before using caps at VIN or VREF/2,

see section 2.3.2 Input Bypass Capacitors.

Absolute with a 2.500V Reference

*For low power, see also LM385-2.5

Absolute with a 5V Reference

Zero-Shift and Span Adjust: 2VsVINs5V Span Adjust: 0VsVINs3V

TL/H/5671–5

Typical Applications (Continued)

Directly Converting a Low-Level Signal

VREF/2e256 mV

AmP Interfaced Comparator

For: VIN(a)lVIN(b)

OutputeFFHEX

For: VIN(a)kVIN(b)

Outpute00HEX

1 mV Resolution with mP Controlled Range

VREF/2e128 mV

1 LSBe1mV

DACsVINs(VDACa256 mV)

Digitizing a Current Flow

TL/H/5671–6

Typical Applications (Continued)

Self-Clocking Multiple A/Ds

*Use a large R value

to reduce loading

at CLK R output.

External Clocking

100 kHzsfCLKs1460 kHz

Self-Clocking in Free-Running Mode

*After power-up, a momentary grounding

of the WR input is needed to guarantee operation.

mP Interface for Free-Running A/D

Operating with ‘‘Automotive’’ Ratiometric Transducers

*VIN(b)e0.15 VCC

15% of VCCsVXDRs85% of VCC

Ratiometric with VREF/2 Forced

TL/H/5671–7

Typical Applications (Continued)

mP Compatible Differential-Input Comparator with Pre-Set VOS (with or without Hysteresis)

*See

Figure 5

to select R value

DB7e‘‘1’’ for VIN(a)lVIN(b)a(VREF/2)

Omit circuitry within the dotted area if

hysteresis is not needed

Handling g10V Analog Inputs

*Beckman Instruments Ý694-3-R10K resistor array

Low-Cost, mP Interfaced, Temperature-to-Digital Converter

mP Interfaced Temperature-to-Digital Converter

*Circuit values shown are for 0§CsTAsa128§C

**Can calibrate each sensor to allow easy replacement, then

A/D can be calibrated with a pre-set input voltage.

TL/H/5671–8

Typical Applications (Continued)

Handling g5V Analog Inputs

TL/H/5671–33

*Beckman Instruments Ý694-3-R10K resistor array

Read-Only Interface

TL/H/5671–34

mP Interfaced Comparator with Hysteresis

TL/H/5671–35

Analog Self-Test for a System

TL/H/5671–36

Protecting the Input

TL/H/5671–9

A Low-Cost, 3-Decade Logarithmic Converter

TL/H/5671–37

*LM389 transistors

A, B, C, D eLM324A quad op amp

Diodes are 1N914

Typical Applications (Continued)

3-Decade Logarithmic A/D Converter

Noise Filtering the Analog Input

fCe20 Hz

Uses Chebyshev implementation for steeper roll-off

unity-gain, 2nd order, low-pass filter

Adding a separate filter for each channel increases

system response time if an analog multiplexer

is used

Multiplexing Differential Inputs

Output Buffers with A/D Data Enabled

*A/D output data is updated 1 CLK period

prior to assertion of INTR

Increasing Bus Drive and/or Reducing Time on Bus

*Allows output data to set-up at falling edge of CS

TL/H/5671–10

Typical Applications (Continued)

Sampling an AC Input Signal

Note 1: Oversample whenever possible [keep fs l2f(b60)]to eliminate input frequency folding

(aliasing) and to allow for the skirt response of the filter.

Note 2: Consider the amplitude errors which are introduced within the passband of the filter.

70% Power Savings by Clock Gating

(Complete shutdown takes &30 seconds.)

Power Savings by A/D and VREF Shutdown

TL/H/5671–11

*Use ADC0801, 02, 03 or 05 for lowest power consumption.

Note: Logic inputs can be driven to VCC with A/D supply at zero volts.

Buffer prevents data bus from overdriving output of A/D when in shutdown mode.

Functional Description

1.0 UNDERSTANDING A/D ERROR SPECS

A perfect A/D transfer characteristic (staircase waveform) is

shown in

Figure 1a

. The horizontal scale is analog input

voltage and the particular points labeled are in steps of 1

LSB (19.53 mV with 2.5V tied to the VREF/2 pin). The digital

output codes that correspond to these inputs are shown as

Db1, D, and Da1. For the perfect A/D, not only will center-

value (Ab1, A, Aa1,....)analog inputs produce the cor-

rect output ditigal codes, but also each riser (the transitions

between adjacent output codes) will be located g(/2 LSB

away from each center-value. As shown, the risers are ideal

and have no width. Correct digital output codes will be pro-

vided for a range of analog input voltages that extend g(/2

LSB from the ideal center-values. Each tread (the range of

analog input voltage that provides the same digital output

code) is therefore 1 LSB wide.

Figure 1b

shows a worst case error plot for the ADC0801.

All center-valued inputs are guaranteed to produce the cor-

rect output codes and the adjacent risers are guaranteed to

be no closer to the center-value points than g(/4 LSB. In

other words, if we apply an analog input equal to the center-

value g(/4 LSB,

we guarantee

that the A/D will produce the

correct digital code. The maximum range of the position of

the code transition is indicated by the horizontal arrow and it

is guaranteed to be no more than (/2 LSB.

The error curve of

Figure 1c

shows a worst case error plot

for the ADC0802. Here we guarantee that if we apply an

analog input equal to the LSB analog voltage center-value

the A/D will produce the correct digital code.

Next to each transfer function is shown the corresponding

error plot. Many people may be more familiar with error plots

than transfer functions. The analog input voltage to the A/D

is provided by either a linear ramp or by the discrete output

steps of a high resolution DAC. Notice that the error is con-

tinuously displayed and includes the quantization uncertain-

ty of the A/D. For example the error at point 1 of

Figure 1a

is a(/2 LSB because the digital code appeared (/2 LSB in

advance of the center-value of the tread. The error plots

always have a constant negative slope and the abrupt up-

side steps are always 1 LSB in magnitude.

Transfer Function Error Plot

a) Accuracyeg0 LSB: A Perfect A/D

Transfer Function Error Plot

b) Accuracyeg(/4 LSB

Transfer Function Error Plot

c) Accuracyeg(/2 LSB TL/H/5671–12

FIGURE 1. Clarifying the Error Specs of an A/D Converter

Functional Description (Continued)

2.0 FUNCTIONAL DESCRIPTION

The ADC0801 series contains a circuit equivalent of the

256R network. Analog switches are sequenced by succes-

sive approximation logic to match the analog difference in-

put voltage [VIN(a)bVIN(b)]to a corresponding tap on

the R network. The most significant bit is tested first and

after 8 comparisons (64 clock cycles) a digital 8-bit binary

code (1111 1111 efull-scale) is transferred to an output

latch and then an interrupt is asserted (INTR makes a high-

to-low transition). A conversion in process can be interrupt-

ed by issuing a second start command. The device may be

operated in the free-running mode by connecting INTR to

the WR input with CSe0. To ensure start-up under all pos-

sible conditions, an external WR pulse is required during the

first power-up cycle.

On the high-to-low transition of the WR input the internal

SAR latches and the shift register stages are reset. As long

as the CS input and WR input remain low, the A/D will re-

main in a reset state.

Conversion will start from 1 to 8 clock

periods after at least one of these inputs makes a low-to-

high transition

A functional diagram of the A/D converter is shown in

Fig-

ure 2

. All of the package pinouts are shown and the major

logic control paths are drawn in heavier weight lines.

The converter is started by having CS and WR simulta-

neously low. This sets the start flip-flop (F/F) and the result-

ing ‘‘1’’ level resets the 8-bit shift register, resets the Inter-

rupt (INTR) F/F and inputs a ‘‘1’’ to the D flop, F/F1, which

is at the input end of the 8-bit shift register. Internal clock

signals then transfer this ‘‘1’’ to the Q output of F/F1. The

AND gate, G1, combines this ‘‘1’’ output with a clock signal

to provide a reset signal to the start F/F. If the set signal is

no longer present (either WR or CS is a ‘‘1’’) the start F/F is

reset and the 8-bit shift register then can have the ‘‘1’’

clocked in, which starts the conversion process. If the set

signal were to still be present, this reset pulse would have

no effect (both outputs of the start F/F would momentarily

be at a ‘‘1’’ level) and the 8-bit shift register would continue

to be held in the reset mode. This logic therefore allows for

wide CS and WR signals and the converter will start after at

least one of these signals returns high and the internal

clocks again provide a reset signal for the start F/F.

TL/H/5671–13

Note 1: CS shown twice for clarity.

Note 2: SAR eSuccessive Approximation Register.

FIGURE 2. Block Diagram

Functional Description (Continued)

After the ‘‘1’’ is clocked through the 8-bit shift register

(which completes the SAR search) it appears as the input to

the D-type latch, LATCH 1. As soon as this ‘‘1’’ is output

from the shift register, the AND gate, G2, causes the new

digital word to transfer to the TRI-STATE output latches.

When LATCH 1 is subsequently enabled, the Q output

makes a high-to-low transition which causes the INTR F/F

to set. An inverting buffer then supplies the INTR input sig-

nal.

Note that this SET control of the INTR F/F remains low for

8 of the external clock periods (as the internal clocks run at

(/8 of the frequency of the external clock). If the data output

is continuously enabled (CS and RD both held low), the

INTR output will still signal the end of conversion (by a high-

to-low transition), because the SET input can control the Q

output of the INTR F/F even though the RESET input is

constantly at a ‘‘1’’ level in this operating mode. This INTR

output will therefore stay low for the duration of the SET

signal, which is 8 periods of the external clock frequency

(assuming the A/D is not started during this interval).

When operating in the free-running or continuous conver-

sion mode (INTR pin tied to WR and CS wired lowÐsee

also section 2.8), the START F/F is SET by the high-to-low

transition of the INTR signal. This resets the SHIFT REGIS-

TER which causes the input to the D-type latch, LATCH 1,

to go low. As the latch enable input is still present, the Q

output will go high, which then allows the INTR F/F to be

RESET. This reduces the width of the resulting INTR output

pulse to only a few propagation delays (approximately 300

ns).

When data is to be read, the combination of both CS and

RD being low will cause the INTR F/F to be reset and the

TRI-STATE output latches will be enabled to provide the 8-

bit digital outputs.

2.1 Digital Control Inputs

The digital control inputs (CS,RD, and WR) meet standard

T2L logic voltage levels. These signals have been renamed

when compared to the standard A/D Start and Output En-

able labels. In addition, these inputs are active low to allow

an easy interface to microprocessor control busses. For

non-microprocessor based applications, the CS input (pin 1)

can be grounded and the standard A/D Start function is

obtained by an active low pulse applied at the WR input (pin

3) and the Output Enable function is caused by an active

low pulse at the RD input (pin 2).

2.2 Analog Differential Voltage Inputs and

Common-Mode Rejection

This A/D has additional applications flexibility due to the

analog differential voltage input. The VIN(b) input (pin 7)

can be used to automatically subtract a fixed voltage value

from the input reading (tare correction). This is also useful in

4 mA– 20 mA current loop conversion. In addition, common-

mode noise can be reduced by use of the differential input.

The time interval between sampling VIN(a) and VIN(b)is4-

(/2 clock periods. The maximum error voltage due to this

slight time difference between the input voltage samples is

given by:

DVe(MAX) e(VP)(2qf

cm)#4.5

fCLK J,

where:

DVeis the error voltage due to sampling delay

VPis the peak value of the common-mode voltage

fcm is the common-mode frequency

As an example, to keep this error to (/4 LSB (E5 mV) when

operating with a 60 Hz common-mode frequency, fcm, and

using a 640 kHz A/D clock, fCLK, would allow a peak value

of the common-mode voltage, VP, which is given by:

VPe[DVe(MAX) (fCLK)]

(2qfcm) (4.5)

VPe(5 c10b3) (640c103)

(6.28) (60) (4.5)

which gives

VPj1.9V.

The allowed range of analog input voltages usually places

more severe restrictions on input common-mode noise lev-

els.

An analog input voltage with a reduced span and a relatively

large zero offset can be handled easily by making use of the

differential input (see section 2.4 Reference Voltage).

2.3 Analog Inputs

2.3.1 Input Current

Normal Mode

Due to the internal switching action, displacement currents

will flow at the analog inputs. This is due to on-chip stray

capacitance to ground as shown in

Figure 3

TL/H/5671–14

rON of SW 1 and SW 2 j5kX

ON CSTRAY j5kXc12 pF e60 ns

FIGURE 3. Analog Input Impedance

Functional Description (Continued)

The voltage on this capacitance is switched and will result in

currents entering the VIN(a) input pin and leaving the

VIN(b) input which will depend on the analog differential

input voltage levels. These current transients occur at the

leading edge of the internal clocks. They rapidly decay and

do not cause errors

as the on-chip comparator is strobed at

the end of the clock period.

Fault Mode

If the voltage source applied to the VIN(a)orV

IN(b) pin

exceeds the allowed operating range of VCCa50 mV, large

input currents can flow through a parasitic diode to the VCC

pin. If these currents can exceed the 1 mA max allowed

spec, an external diode (1N914) should be added to bypass

this current to the VCC pin (with the current bypassed with

this diode, the voltage at the VIN(a) pin can exceed the

VCC voltage by the forward voltage of this diode).

2.3.2 Input Bypass Capacitors

Bypass capacitors at the inputs will average these charges

and cause a DC current to flow through the output resist-

ances of the analog signal sources. This charge pumping

action is worse for continuous conversions with the VIN(a)

input voltage at full-scale. For continuous conversions with

a 640 kHz clock frequency with the VIN(a) input at 5V, this

DC current is at a maximum of approximately 5 mA. There-

fore,

bypass capacitors should not be used at the analog

inputs or the V

REF

/2 pin

for high resistance sources (l1

kX). If input bypass capacitors are necessary for noise filter-

ing and high source resistance is desirable to minimize ca-

pacitor size, the detrimental effects of the voltage drop

across this input resistance, which is due to the average

value of the input current, can be eliminated with a full-scale

adjustment while the given source resistor and input bypass

capacitor are both in place. This is possible because the

average value of the input current is a precise linear func-

tion of the differential input voltage.

2.3.3 Input Source Resistance

Large values of source resistance where an input bypass

capacitor is not used,

will not cause errors

as the input cur-

rents settle out prior to the comparison time. If a low pass

filter is required in the system, use a low valued series resis-

tor (s1kX) for a passive RC section or add an op amp RC

active low pass filter. For low source resistance applica-

tions, (s1kX), a 0.1 mF bypass capacitor at the inputs will

prevent noise pickup due to series lead inductance of a long

wire. A 100Xseries resistor can be used to isolate this ca-

pacitorÐboth the R and C are placed outside the feedback

loopÐfrom the output of an op amp, if used.

2.3.4 Noise

The leads to the analog inputs (pin 6 and 7) should be kept

as short as possible to minimize input noise coupling. Both

noise and undesired digital clock coupling to these inputs

can cause system errors. The source resistance for these

inputs should, in general, be kept below 5 kX. Larger values

of source resistance can cause undesired system noise

pickup. Input bypass capacitors, placed from the analog in-

puts to ground, will eliminate system noise pickup but can

create analog scale errors as these capacitors will average

the transient input switching currents of the A/D (see sec-

tion 2.3.1.). This scale error depends on both a large source

resistance and the use of an input bypass capacitor. This

error can be eliminated by doing a full-scale adjustment of

the A/D (adjust VREF/2 for a proper full-scale readingÐsee

section 2.5.2 on Full-Scale Adjustment) with the source re-

sistance and input bypass capacitor in place.

2.4 Reference Voltage

2.4.1 Span Adjust

For maximum applications flexibility, these A/Ds have been

designed to accommodatea5V

DC, 2.5 VDC or an adjusted

voltage reference. This has been achieved in the design of

the IC as shown in

Figure 4

TL/H/5671–15

FIGURE 4. The VREFERENCE Design on the IC

Notice that the reference voltage for the IC is either (/2 of

the voltage applied to the VCC supply pin, or is equal to the

voltage that is externally forced at the VREF/2 pin. This al-

lows for a ratiometric voltage reference using the VCC sup-

ply, a 5 VDC reference voltage can be used for the VCC

supply or a voltage less than 2.5 VDC can be applied to the

VREF/2 input for increased application flexibility. The inter-

nal gain to the VREF/2 input is 2, making the full-scale differ-

ential input voltage twice the voltage at pin 9.

An example of the use of an adjusted reference voltage is to

accommodate a reduced spanÐor dynamic voltage range

of the analog input voltage. If the analog input voltage were

to range from 0.5 VDC to 3.5 VDC, instead of 0V to 5 VDC,

the span would be 3V as shown in

Figure 5

. With 0.5 VDC

applied to the VIN(b) pin to absorb the offset, the reference

voltage can be made equal to (/2 of the 3V span or 1.5 VDC.

The A/D now will encode the VIN(a) signal from 0.5V to 3.5

V with the 0.5V input corresponding to zero and the 3.5 VDC

input corresponding to full-scale. The full 8 bits of resolution

are therefore applied over this reduced analog input voltage

range.

Functional Description (Continued)

*Add if VREF/2 s1V

DC with LM358

to draw 3 mA to ground.

TL/H/5671–16

a) Analog Input Signal Example b) Accommodating an Analog Input from

0.5V (Digital Out ee00HEX) to 3.5V

(Digital OuteFFHEX)

FIGURE 5. Adapting the A/D Analog Input Voltages to Match an Arbitrary Input Signal Range

2.4.2 Reference Accuracy Requirements

The converter can be operated in a ratiometric mode or an

absolute mode. In ratiometric converter applications, the

magnitude of the reference voltage is a factor in both the

output of the source transducer and the output of the A/D

converter and therefore cancels out in the final digital output

code. The ADC0805 is specified particularly for use in ratio-

metric applications with no adjustments required. In abso-

lute conversion applications, both the initial value and the

temperature stability of the reference voltage are important

factors in the accuracy of the A/D converter. For VREF/2

voltages of 2.4 VDC nominal value, initial errors of g10

mVDC will cause conversion errors of g1 LSB due to the

gain of 2 of the VREF/2 input. In reduced span applications,

the initial value and the stability of the VREF/2 input voltage

become even more important. For example, if the span is

reduced to 2.5V, the analog input LSB voltage value is cor-

respondingly reduced from 20 mV (5V span) to 10 mV and

1 LSB at the VREF/2 input becomes 5 mV. As can be seen,

this reduces the allowed initial tolerance of the reference

voltage and requires correspondingly less absolute change

with temperature variations. Note that spans smaller than

2.5V place even tighter requirements on the initial accuracy

and stability of the reference source.

In general, the magnitude of the reference voltage will re-

quire an initial adjustment. Errors due to an improper value

of reference voltage appear as full-scale errors in the A/D

transfer function. IC voltage regulators may be used for ref-

erences if the ambient temperature changes are not exces-

sive. The LM336B 2.5V IC reference diode (from National

Semiconductor) has a temperature stability of 1.8 mV typ

(6 mV max) over 0§CsTAsa70§C. Other temperature

range parts are also available.

2.5 Errors and Reference Voltage Adjustments

2.5.1 Zero Error

The zero of the A/D does not require adjustment. If the

minimum analog input voltage value, VIN(MIN), is not ground,

a zero offset can be done. The converter can be made to

output 0000 0000 digital code for this minimum input voltage

by biasing the A/D VIN(b) input at this VIN(MIN) value (see

Applications section). This utilizes the differential mode op-

eration of the A/D.

The zero error of the A/D converter relates to the location

of the first riser of the transfer function and can be mea-

sured by grounding the VIN (b) input and applying a small

magnitude positive voltage to the VIN (a) input. Zero error

is the difference between the actual DC input voltage that is

necessary to just cause an output digital code transition

from 0000 0000 to 0000 0001 and the ideal (/2 LSB value

((/2 LSB e9.8 mV for VREF/2e2.500 VDC).

2.5.2 Full-Scale

The full-scale adjustment can be made by applying a differ-

ential input voltage that is 1(/2 LSB less than the desired

analog full-scale voltage range and then adjusting the mag-

nitude of the VREF/2 input (pin 9 or the VCC supply if pin 9 is

not used) for a digital output code that is just changing from

1111 1110 to 1111 1111.

Functional Description (Continued)

2.5.3 Adjusting for an Arbitrary Analog Input Voltage

Range

If the analog zero voltage of the A/D is shifted away from

ground (for example, to accommodate an analog input sig-

nal that does not go to ground) this new zero reference

should be properly adjusted first. A VIN(a) voltage that

equals this desired zero reference plus (/2 LSB (where the

LSB is calculated for the desired analog span, 1 LSBeana-

log span/256) is applied to pin 6 and the zero reference

voltage at pin 7 should then be adjusted to just obtain the

00HEX to 01HEX code transition.

The full-scale adjustment should then be made (with the

proper VIN(b) voltage applied) by forcing a voltage to the

VIN(a) input which is given by:

VIN (a)fsadjeV

MAXb1.5 Ð(VMAX bVMIN)

256 (,

where:

VMAXeThe high end of the analog input range

and

VMINethe low end (the offset zero) of the analog range.

(Both are ground referenced.)

The VREF/2 (or VCC) voltage is then adjusted to provide a

code change from FEHEX to FFHEX. This completes the ad-

justment procedure.

2.6 Clocking Option

The clock for the A/D can be derived from the CPU clock or

an external RC can be added to provide self-clocking. The

CLK IN (pin 4) makes use of a Schmitt trigger as shown in

Figure 6

fCLKj1

1.1 RC

Rj10 kX

TL/H/5671–17

FIGURE 6. Self-Clocking the A/D

Heavy capacitive or DC loading of the clock R pin should be

avoided as this will disturb normal converter operation.

Loads less than 50 pF, such as driving up to 7 A/D convert-

er clock inputs from a single clock R pin of 1 converter, are

allowed. For larger clock line loading, a CMOS or low power

TTL buffer or PNP input logic should be used to minimize

the loading on the clock R pin (do not use a standard TTL

buffer).

2.7 Restart During a Conversion

If the A/D is restarted (CS and WR go low and return high)

during a conversion, the converter is reset and a new con-

version is started. The output data latch is not updated if the

conversion in process is not allowed to be completed, there-

fore the data of the previous conversion remains in this

latch. The INTR output simply remains at the ‘‘1’’ level.

2.8 Continuous Conversions

For operation in the free-running mode an initializing pulse

should be used, following power-up, to ensure circuit opera-

tion. In this application, the CS input is grounded and the

WR input is tied to the INTR output. This WR and INTR

node should be momentarily forced to logic low following a

power-up cycle to guarantee operation.

2.9 Driving the Data Bus

This MOS A/D, like MOS microprocessors and memories,

will require a bus driver when the total capacitance of the

data bus gets large. Other circuitry, which is tied to the data

bus, will add to the total capacitive loading, even in TRI-

STATE (high impedance mode). Backplane bussing also

greatly adds to the stray capacitance of the data bus.

There are some alternatives available to the designer to

handle this problem. Basically, the capacitive loading of the

data bus slows down the response time, even though DC

specifications are still met. For systems operating with a

relatively slow CPU clock frequency, more time is available

in which to establish proper logic levels on the bus and

therefore higher capacitive loads can be driven (see typical

characteristics curves).

At higher CPU clock frequencies time can be extended for

I/O reads (and/or writes) by inserting wait states (8080) or

using clock extending circuits (6800).

Finally, if time is short and capacitive loading is high, exter-

nal bus drivers must be used. These can be TRI-STATE

buffers (low power Schottky such as the DM74LS240 series

is recommended) or special higher drive current products

which are designed as bus drivers. High current bipolar bus

drivers with PNP inputs are recommended.

2.10 Power Supplies

Noise spikes on the VCC supply line can cause conversion

errors as the comparator will respond to this noise. A low

inductance tantalum filter capacitor should be used close to

the converter VCC pin and values of 1 mF or greater are

recommended. If an unregulated voltage is available in the

system, a separate LM340LAZ-5.0, TO-92, 5V voltage regu-

lator for the converter (and other analog circuitry) will greatly

reduce digital noise on the VCC supply.

2.11 Wiring and Hook-Up Precautions

Standard digital wire wrap sockets are not satisfactory for

breadboarding this A/D converter. Sockets on PC boards

can be used and all logic signal wires and leads should be

grouped and kept as far away as possible from the analog

signal leads. Exposed leads to the analog inputs can cause

undesired digital noise and hum pickup, therefore shielded

leads may be necessary in many applications.

Functional Description (Continued)

A single point analog ground that is separate from the logic

ground points should be used. The power supply bypass

capacitor and the self-clocking capacitor (if used) should

both be returned to digital ground. Any VREF/2 bypass ca-

pacitors, analog input filter capacitors, or input signal shield-

ing should be returned to the analog ground point. A test for

proper grounding is to measure the zero error of the A/D

converter. Zero errors in excess of (/4 LSB can usually be

traced to improper board layout and wiring (see section

2.5.1 for measuring the zero error).

3.0 TESTING THE A/D CONVERTER

There are many degrees of complexity associated with test-

ing an A/D converter. One of the simplest tests is to apply a

known analog input voltage to the converter and use LEDs

to display the resulting digital output code as shown in

Fig-

ure 7

For ease of testing, the VREF/2 (pin 9) should be supplied

with 2.560 VDC andaV

CC supply voltage of 5.12 VDC

should be used. This provides an LSB value of 20 mV.

If a full-scale adjustment is to be made, an analog input

voltage of 5.090 VDC (5.120– 1(/2 LSB) should be applied to

the VIN(a) pin with the VIN(b) pin grounded. The value of

the VREF/2 input voltage should then be adjusted until the

digital output code is just changing from 1111 1110 to 1111

1111. This value of VREF/2 should then be used for all the

tests.

The digital output LED display can be decoded by dividing

the 8 bits into 2 hex characters, the 4 most significant (MS)

and the 4 least significant (LS). Table I shows the fractional

binary equivalent of these two 4-bit groups. By adding the

voltages obtained from the ‘‘VMS’’ and ‘‘VLS’’ columns in

Table I, the nominal value of the digital display (when

TL/H/5671–18

FIGURE 7. Basic A/D Tester

VREF/2 e2.560V) can be determined. For example, for an

output LED display of 1011 0110 or B6 (in hex), the voltage

values from the table are 3.520 a0.120 or 3.640 VDC.

These voltage values represent the center-values of a per-

fect A/D converter. The effects of quantization error have to

be accounted for in the interpretation of the test results.

For a higher speed test system, or to obtain plotted data, a

digital-to-analog converter is needed for the test set-up. An

accurate 10-bit DAC can serve as the precision voltage

source for the A/D. Errors of the A/D under test can be

expressed as either analog voltages or differences in 2 digi-

tal words.

A basic A/D tester that uses a DAC and provides the error

as an analog output voltage is shown in

Figure 8

.The2op

amps can be eliminated if a lab DVM with a numerical sub-

traction feature is available to read the difference voltage,

‘‘A– C’’, directly. The analog input voltage can be supplied

by a low frequency ramp generator and an X-Y plotter can

be used to provide analog error (Y axis) versus analog input

(X axis).

For operation with a microprocessor or a computer-based

test system, it is more convenient to present the errors digi-

tally. This can be done with the circuit of

Figure 9

, where the

output code transitions can be detected as the 10-bit DAC is

incremented. This provides (/4 LSB steps for the 8-bit A/D

under test. If the results of this test are automatically plotted

with the analog input on the X axis and the error (in LSB’s)

as the Y axis, a useful transfer function of the A/D under

test results. For acceptance testing, the plot is not neces-

sary and the testing speed can be increased by establishing

internal limits on the allowed error for each code.

4.0 MICROPROCESSOR INTERFACING

To dicuss the interface with 8080A and 6800 microproces-

sors, a common sample subroutine structure is used. The

microprocessor starts the A/D, reads and stores the results

of 16 successive conversions, then returns to the user’s

program. The 16 data bytes are stored in 16 successive

memory locations. All Data and Addresses will be given in

hexadecimal form. Software and hardware details are pro-

vided separately for each type of microprocessor.

4.1 Interfacing 8080 Microprocessor Derivatives (8048,

8085)

This converter has been designed to directly interface with

derivatives of the 8080 microprocessor. The A/D can be

mapped into memory space (using standard memory ad-

dress decoding for CS and the MEMR and MEMW strobes)

or it can be controlled as an I/O device by using the I/O R

and I/O W strobes and decoding the address bits A0

A7 (or address bits A8

A15 as they will contain the

same 8-bit address information) to obtain the CS input. Us-

ing the I/O space provides 256 additional addresses and

may allow a simpler 8-bit address decoder but the data can

only be input to the accumulator. To make use of the addi-

tional memory reference instructions, the A/D should be

mapped into memory space. An example of an A/D in I/O

space is shown in

Figure 10

Functional Description (Continued)

FIGURE 8. A/D Tester with Analog Error Output

TL/H/5671–19

FIGURE 9. Basic ‘‘Digital’’ A/D Tester

TABLE I. DECODING THE DIGITAL OUTPUT LEDs

OUTPUT VOLTAGE

FRACTIONAL BINARY VALUE FOR CENTER VALUES

HEX BINARY WITH

VREF/2e2.560 VDC

MS GROUP LS GROUP VMS GROUP*VLS GROUP*

F 1 1 1 1 15/16 15/256 4.800 0.300

E 1 1 1 0 7/8 7/128 4.480 0.280

D 1 1 0 1 13/16 13/256 4.160 0.260

C 1 1 0 0 3/4 3/64 3.840 0.240

B 1 0 1 1 11/16 11/256 3.520 0.220

A 1 0 1 0 5/8 5/128 3.200 0.200

9 1 0 0 1 9/16 9/256 2/880 0.180

8 1 0 0 0 1/2 1/32 2/560 0.160

7 0 1 1 1 7/16 7/256 2.240 0.140

6 0 1 1 0 3/8 3/128 1.920 0.120

5 0 1 0 1 5/16 2/256 1.600 0.100

4 0 1 0 0 1/4 1/64 1/280 0.080

3 0 0 1 1 3/16 3/256 0.960 0.060

2 0 0 1 0 1/8 1/128 0.640 0.040

1 0 0 0 1 1/16 1/256 0.320 0.020

00000 00

*Display OutputeVMS Group aVLS Group

Functional Description (Continued)

TL/H/5671–20

Note 1: *Pin numbers for the DP8228 system controller, others are INS8080A.

Note 2: Pin 23 of the INS8228 must be tied to a12V througha1kXresistor to generate the RST 7

instruction when an interrupt is acknowledged as required by the accompanying sample program.

FIGURE 10. ADC0801– INS8080A CPU Interface

SAMPLE PROGRAM FOR

FIGURE 10

ADC0801– INS8080A CPU INTERFACE

0038 C3 00 03 RST 7: JMP LD DATA

## #

0100 21 00 02 START: LXI H 0200H ; HL pair will point to

; data storage locations

0103 31 00 04 RETURN: LXI SP 0400H ; Initialize stack pointer (Note 1)

0106 7D MOV A, L ; Test #of bytes entered

0107 FE OF CPI OF H ; If #416. JMP to

0109 CA 13 01 JZ CONT ; user program

010C D3 E0 OUT E0 H ; Start A/D

010E FB EI ; Enable interrupt

010F 00 LOOP: NOP ; Loop until end of

0110 C3 OF 01 JMP LOOP ; conversion

0113 #CONT: #

### #

(User program to #

process data) #

### #

0300 DB E0 LD DATA: IN E0 H ; Load data into accumulator

0302 77 MOV M, A ; Store data

0303 23 INX H ; Increment storage pointer

0304 C3 03 01 JMP RETURN

Note 1: The stack pointer must be dimensioned because a RST 7 instruction pushes the PC onto the stack.

Note 2: All address used were arbitrarily chosen.

Functional Description (Continued)

The standard control bus signals of the 8080 CS,RDand

WR) can be directly wired to the digital control inputs of the

A/D and the bus timing requirements are met to allow both

starting the converter and outputting the data onto the data

bus. A bus driver should be used for larger microprocessor

systems where the data bus leaves the PC board and/or

must drive capacitive loads larger than 100 pF.

4.1.1 Sample 8080A CPU Interfacing Circuitry and

Program

The following sample program and associated hardware

shown in

Figure 10

may be used to input data from the

converter to the INS8080A CPU chip set (comprised of the

INS8080A microprocessor, the INS8228 system controller

and the INS8224 clock generator). For simplicity, the A/D is

controlled as an I/O device, specifically an 8-bit bi-direction-

al port located at an arbitrarily chosen port address, E0. The

TRI-STATE output capability of the A/D eliminates the need

for a peripheral interface device, however address decoding

is still required to generate the appropriate CS for the con-

verter.

It is important to note that in systems where the A/D con-

verter is 1-of-8 or less I/O mapped devices, no address

decoding circuitry is necessary. Each of the 8 address bits

(A0 to A7) can be directly used as CS inputsÐone for each

I/O device.

4.1.2 INS8048 Interface

The INS8048 interface technique with the ADC0801 series

(see

Figure 11

) is simpler than the 8080A CPU interface.

There are 24 I/O lines and three test input lines in the 8048.

With these extra I/O lines available, one of the I/O lines (bit

0 of port 1) is used as the chip select signal to the A/D, thus

eliminating the use of an external address decoder. Bus

control signals RD,WRand INT of the 8048 are tied directly

to the A/D. The 16 converted data words are stored at on-

chip RAM locations from 20 to 2F (Hex). The RD and WR

signals are generated by reading from and writing into a

dummy address, respectively. A sample interface program

is shown below.

TL/H/5671–21

FIGURE 11. INS8048 Interface

SAMPLE PROGRAM FOR

FIGURE 11

INS8048 INTERFACE

04 10 JMP 10H : Program starts at addr 10

ORG 3H

04 50 JMP 50H ; Interrupt jump vector

ORG 10H ; Main program

99 FE ANL P1, #0FEH ; Chip select

81 MOVX A, @R1 ; Read in the 1st data

; to reset the intr

89 01 START: ORL P1, Ý1 ; Set port pin high

B8 20 MOV R0, #20H ; Data address

B9 FF MOV R1, #0FFH ; Dummy address

BA 10 MOV R2, #10H ; Counter for 16 bytes

23 FF AGAIN: MOV A, #0FFH ; Set ACC for intr loop

99 FE ANL P1, #0FEH ; Send CS (bit 0 of P1)

91 MOVX @R1, A ; Send WR out

05 EN I ; Enable interrupt

96 21 LOOP: JNZ LOOP ; Wait for interrupt

EA 1B DJNZ R2, AGAIN ; If 16 bytes are read

00 NOP ; go to user’s program

00 NOP

ORG 50H

81 INDATA: MOVX A, @R1 ; Input data, CS still low

A0 MOV @R0, A ; Store in memory

18 INC R0 ; Increment storage counter

89 01 ORL P1, #1 ; Reset CS signal

27 CLR A ; Clear ACC to get out of

93 RETR ; the interrupt loop

Functional Description (Continued)

4.2 Interfacing the Z-80

The Z-80 control bus is slightly different from that of the

8080. General RD and WR strobes are provided and sepa-

rate memory request, MREQ, and I/O request, IORQ, sig-

nals are used which have to be combined with the general-

ized strobes to provide the equivalent 8080 signals. An ad-

vantage of operating the A/D in I/O space with the Z-80 is

that the CPU will automatically insert one wait state (the RD

and WR strobes are extended one clock period) to allow

more time for the I/O devices to respond. Logic to map the

A/D in I/O space is shown in

Figure 13

TL/H/5671–23

FIGURE 13. Mapping the A/D as an I/O Device

for Use with the Z-80 CPU

Additional I/O advantages exist as software DMA routines

are available and use can be made of the output data trans-

fer which exists on the upper 8 address lines (A8 to A15)

during I/O input instructions. For example, MUX channel

selection for the A/D can be accomplished with this operat-

ing mode.

4.3 Interfacing 6800 Microprocessor Derivatives

(6502, etc.)

The control bus for the 6800 microprocessor derivatives

does not use the RD and WR strobe signals. Instead it em-

ploys a single R/W line and additional timing, if needed, can

be derived fom the w2 clock. All I/O devices are memory

mapped in the 6800 system, and a special signal, VMA,

indicates that the current address is valid.

Figure 14

shows

an interface schematic where the A/D is memory mapped in

the 6800 system. For simplicity, the CS decoding is shown

using (/2 DM8092. Note that in many 6800 systems, an al-

ready decoded 4/5 line is brought out to the common bus at

pin 21. This can be tied directly to the CS pin of the A/D,

provided that no other devices are addressed at HX ADDR:

4XXX or 5XXX.

The following subroutine performs essentially the same

function as in the case of the 8080A interface and it can be

called from anywhere in the user’s program.

Figure 15

the ADC0801 series is interfaced to the M6800

microprocessor through (the arbitrarily chosen) Port B of the

MC6820 or MC6821 Peripheral Interface Adapter, (PIA).

Here the CS pin of the A/D is grounded since the PIA is

already memory mapped in the M6800 system and no CS

decoding is necessary. Also notice that the A/D output data

lines are connected to the microprocessor bus under pro-

gram control through the PIA and therefore the A/D RD pin

can be grounded.

A sample interface program equivalent to the previous one

is shown below

Figure 15

. The PIA Data and Control Regis-

ters of Port B are located at HEX addresses 8006 and 8007,

respectively.

5.0 GENERAL APPLICATIONS

The following applications show some interesting uses for

the A/D. The fact that one particular microprocessor is used

is not meant to be restrictive. Each of these application cir-

cuits would have its counterpart using any microprocessor

that is desired.

5.1 Multiple ADC0801 Series to MC6800 CPU Interface

To transfer analog data from several channels to a single

microprocessor system, a multiple converter scheme pre-

sents several advantages over the conventional multiplexer

single-converter approach. With the ADC0801 series, the

differential inputs allow individual span adjustment for each

channel. Furthermore, all analog input channels are sensed

simultaneously, which essentially divides the microproces-

sor’s total system servicing time by the number of channels,

since all conversions occur simultaneously. This scheme is

shown in

Figure 16

TL/H/5671–24

Note 1: Numbers in parentheses refer to MC6800 CPU pin out.

FIGURE 14. ADC0801-MC6800 CPU Interface

Note 2: Number or letters in brackets refer to standard M6800 system common bus code.

Functional Description (Continued)

SAMPLE PROGRAM FOR

FIGURE 14

ADC0801-MC6800 CPU INTERFACE

0010 DF 36 DATAIN STX TEMP2 ; Save contents of X

0012 CE 00 2C LDX #$002C ; Upon IRQ low CPU

0015 FF FF F8 STX $FFF8 ; jumps to 002C

0018 B7 50 00 STAA $5000 ; Start ADC0801

001B 0E CLI

001C 3E CONVRT WAI ; Wait for interrupt

001D DE 34 LDX TEMP1

001F 8C 02 0F CPX #$020F ; Is final data stored?

0022 27 14 BEQ ENDP

0024 B7 50 00 STAA $5000 ; Restarts ADC0801

0027 08 INX

0028 DF 34 STX TEMP1

002A 20 F0 BRA CONVRT

002C DE 34 INTRPT LDX TEMP1

002E B6 50 00 LDAA $5000 ; Read data

0031 A7 00 STAA X ; Store it at X

0033 3B RTI

0034 02 00 TEMP1 FDB $0200 ; Starting address for

; data storage

0036 00 00 TEMP2 FDB $0000

0038 CE 02 00 ENDP LDX #$0200 ; Reinitialize TEMP1

003B DF 34 STX TEMP1

003D DE 36 LDX TEMP2

003F 39 RTS ; Return from subroutine

; To user’s program

Note 1: In order for the microprocessor to service subroutines and interrupts, the stack pointer must be dimensioned in the user’s program.

TL/H/5671–25

FIGURE 15. ADC0801– MC6820 PIA Interface

Functional Description (Continued)

SAMPLE PROGRAM FOR

FIGURE 15

ADC0801– MC6820 PIA INTERFACE

0010 CE 00 38 DATAIN LDX #$0038 ; Upon IRQ low CPU

0013 FF FF F8 STX $FFF8 ; jumps to 0038

0016 B6 80 06 LDAA PIAORB ; Clear possible IRQ flags

0019 4F CLRA

001A B7 80 07 STAA PIACRB

001D B7 80 06 STAA PIAORB ; Set Port B as input

0020 0E CLI

0021 C6 34 LDAB #$34

0023 86 3D LDAA #$3D

0025 F7 80 07 CONVRT STAB PIACRB ; Starts ADC0801

0028 B7 80 07 STAA PIACRB

002B 3E WAI ; Wait for interrupt

002C DE 40 LDX TEMP1

002E 8C 02 0F CPX #$020F ; Is final data stored?

0031 27 0F BEQ ENDP

0033 08 INX

0034 DF 40 STX TEMP1

0036 20 ED BRA CONVRT

0038 DE 40 INTRPT LDX TEMP1

003A B6 80 06 LDAA PIAORB ; Read data in

003D A7 00 STAA X ; Store it at X

003F 3B RTI

0040 02 00 TEMP1 FDB $0200 ; Starting address for

; data storage

0042 CE 02 00 ENDP LDX #$0200 ; Reinitialize TEMP1

0045 DF 40 STX TEMP1

0047 39 RTS ; Return from subroutine

PIAORB EQU $8006 ; To user’s program

PIACRB EQU $8007

The following schematic and sample subroutine (DATA IN)

may be used to interface (up to) 8 ADC0801’s directly to the

MC6800 CPU. This scheme can easily be extended to allow

the interface of more converters. In this configuration the

converters are (arbitrarily) located at HEX address 5000 in

the MC6800 memory space. To save components, the

clock signal is derived from just one RC pair on the first

converter. This output drives the other A/Ds.

All the converters are started simultaneously with a STORE

instruction at HEX address 5000. Note that any other HEX

address of the form 5XXX will be decoded by the circuit,

pulling all the CS inputs low. This can easily be avoided by

using a more definitive address decoding scheme. All the

interrupts are ORed together to insure that all A/Ds have

completed their conversion before the microprocessor is in-

terrupted.

The subroutine, DATA IN, may be called from anywhere in

the user’s program. Once called, this routine initializes the

CPU, starts all the converters simultaneously and waits for

the interrupt signal. Upon receiving the interrupt, it reads the

converters (from HEX addresses 5000 through 5007) and

stores the data successively at (arbitrarily chosen) HEX ad-

dresses 0200 to 0207, before returning to the user’s pro-

gram. All CPU registers then recover the original data they

had before servicing DATA IN.

5.2 Auto-Zeroed Differential Transducer Amplifier

and A/D Converter

The differential inputs of the ADC0801 series eliminate the

need to perform a differential to single ended conversion for

a differential transducer. Thus, one op amp can be eliminat-

ed since the differential to single ended conversion is pro-

vided by the differential input of the ADC0801 series. In gen-

eral, a transducer preamp is required to take advantage of

the full A/D converter input dynamic range.

Functional Description (Continued)

TL/H/5671–26

Note 1: Numbers in parentheses refer to MC6800 CPU pin out.

Note 2: Numbers of letters in brackets refer to standard M6800 system common bus code.

FIGURE 16. Interfacing Multiple A/Ds in an MC6800 System

SAMPLE PROGRAM FOR

FIGURE 16

INTERFACING MULTIPLE A/Ds IN AN MC6800 SYSTEM

ADDRESS HEX CODE MNEMONICS COMMENTS

0010 DF 44 DATAIN STX TEMP ; Save Contents of X

0012 CE 00 2A LDX #$002A ; Upon IRQ LOW CPU

0015 FF FF F8 STX $FFF8 ; Jumps to 002A

0018 B7 50 00 STAA $5000 ; Starts all A/D’s

001B 0E CLI

001C 3E WAI ; Wait for interrupt

001D CE 50 00 LDX #$5000

0020 DF 40 STX INDEX1 ; Reset both INDEX

0022 CE 02 00 LDX #$0200 ; 1 and 2 to starting

0025 DF 42 STX INDEX2 ; addresses

0027 DE 44 LDX TEMP

0029 39 RTS ; Return from subroutine

002A DE 40 INTRPT LDX INDEX1 ; INDEX1

002C A6 00 LDAA X ; Read data in from A/D at X

002E 08 INX ; Increment X by one

002F DF 40 STX INDEX1 ; X

INDEX1

0031 DE 42 LDX INDEX2 ; INDEX2

Functional Description (Continued)

SAMPLE PROGRAM FOR

FIGURE 16

INTERFACING MULTIPLE A/Ds IN AN MC6800 SYSTEM

ADDRESS HEX CODE MNEMONICS COMMENTS

0033 A7 00 STAA X ; Store data at X

0035 8C 02 07 CPX #$0207 ; Have all A/D’s been read?

0038 27 05 BEQ RETURN ; Yes: branch to RETURN

003A 08 INX ; No: increment X by one

003B DF 42 STX INDEX2 ; X

INDEX2

003D 20 EB BRA INTRPT ; Branch to 002A

003F 3B RETURN RTI

0040 50 00 INDEX1 FDB $5000 ; Starting address for A/D

0042 02 00 INDEX2 FDB $0200 ; Starting address for data storage

0044 00 00 TEMP FDB $0000

Note 1: In order for the microprocessor to service subroutines and interrupts, the stack pointer must be dimensioned in the user’s program.

For amplification of DC input signals, a major system error is

the input offset voltage of the amplifiers used for the

preamp.

Figure 17

is a gain of 100 differential preamp

whose offset voltage errors will be cancelled by a zeroing

subroutine which is performed by the INS8080A microproc-

essor system. The total allowable input offset voltage error

for this preamp is only 50 mV for (/4 LSB error. This would

obviously require very precise amplifiers. The expression for

the differential output voltage of the preamp is:

VOe[VIN(a)bVIN(b)]Ð1a2R2

R1 (a

X ä YXä Y

SIGNAL GAIN

(VOS2bVOS1bVOS3gIXRX)#1a2R2

R1 J

X ä YX ä Y

DC ERROR TERM GAIN

where IXis the current through resistor RX. All of the offset

error terms can be cancelled by making gIXRXeVOS1 a

VOS3 bVOS2. This is the principle of this auto-zeroing

scheme.

The INS8080A uses the 3 I/O ports of an INS8255 Pro-

gramable Peripheral Interface (PPI) to control the auto zero-

ing and input data from the ADC0801 as shown in

Figure 18

The PPI is programmed for basic I/O operation (mode 0)

with Port A being an input port and Ports B and C being

output ports. Two bits of Port C are used to alternately open

or close the 2 switches at the input of the preamp. Switch

SW1 is closed to force the preamp’s differential input to be

zero during the zeroing subroutine and then opened and

SW2 is then closed for conversion of the actual differential

input signal. Using 2 switches in this manner eliminates con-

cern for the ON resistance of the switches as they must

conduct only the input bias current of the input amplifiers.

Output Port B is used as a successive approximation regis-

ter by the 8080 and the binary scaled resistors in series with

each output bit create a D/A converter. During the zeroing

subroutine, the voltage at Vxincreases or decreases as re-

quired to make the differential output voltage equal to zero.

This is accomplished by ensuring that the voltage at the

output of A1 is approximately 2.5V so that a logic ‘‘1’’ (5V)

on any output of Port B will source current into node VXthus

raising the voltage at VXand making the output differential

more negative. Conversely, a logic ‘‘0’’ (0V) will pull current

out of node VXand decrease the voltage, causing the differ-

ential output to become more positive. For the resistor val-

ues shown, VXcan move g12 mV with a resolution of 50

mV, which will null the offset error term to (/4 LSB of full-

scale for the ADC0801. It is important that the voltage levels

that drive the auto-zero resistors be constant. Also, for sym-

metry, a logic swing of 0V to 5V is convenient. To achieve

this, a CMOS buffer is used for the logic output signals of

Port B and this CMOS package is powered with a stable 5V

source. Buffer amplifier A1 is necessary so that it can

source or sink the D/A output current.

Functional Description (Continued)

Note 1: R2 e49.5 R1

Note 2: Switches are LMC13334 CMOS analog switches.

Note 3: The 9 resistors used in the auto-zero section can be g5% tolerance.

FIGURE 17. Gain of 100 Differential Transducer Preamp

TL/H/5671–27

FIGURE 18. Microprocessor Interface Circuitry for Differential Preamp

A flow chart for the zeroing subroutine is shown in

Figure

. It must be noted that the ADC0801 series will output an

all zero code when it converts a negative input [VIN(b)t

VIN(a)]. Also, a logic inversion exists as all of the I/O ports

are buffered with inverting gates.

Basically, if the data read is zero, the differential output volt-

age is negative, so a bit in Port B is cleared to pull VXmore

negative which will make the output more positive for the

next conversion. If the data read is not zero, the output volt-

age is positive so a bit in Port B is set to make VXmore

positive and the output more negative. This continues for 8

approximations and the differential output eventually con-

verges to within 5 mV of zero.

The actual program is given in

Figure 20

. All addresses

used are compatible with the BLC 80/10 microcomputer

system. In particular:

Port A and the ADC0801 are at port address E4

Port B is at port address E5

Port C is at port address E6

PPI control word port is at port address E7

Program Counter automatically goes to ADDR:3C3D upon

acknowledgement of an interrupt from the ADC0801

5.3 Multiple A/D Converters in a Z-80 Interrupt

Driven Mode

In data acquisition systems where more than one A/D con-

verter (or other peripheral device) will be interrupting pro-

gram execution of a microprocessor, there is obviously a

need for the CPU to determine which device requires servic-

ing.

Figure 21

and the accompanying software is a method

of determining which of 7 ADC0801 converters has com-

pleted a conversion (INTR asserted) and is requesting an

interrupt. This circuit allows starting the A/D converters in

any sequence, but will input and store valid data from the

converters with a priority sequence of A/D 1 being read first,

A/D 2 second, etc., through A/D 7 which would have the

lowest priority for data being read. Only the converters

whose INT is asserted will be read.

The key to decoding circuitry is the DM74LS373, 8-bit D

type flip-flop. When the Z-80 acknowledges the interrupt,

the program is vectored to a data input Z-80 subroutine.

This subroutine will read a peripheral status word from the

DM74LS373 which contains the logic state of the INTR out-

puts of all the converters. Each converter which initiates an

interrupt will place a logic ‘‘0’’ in a unique bit position in the

status word and the subroutine will determine the identity of

the converter and execute a data read. An identifier word

(which indicates which A/D the data came from) is stored in

the next sequential memory location above the location of

the data so the program can keep track of the identity of the

data entered.

TL/H/5671–28

FIGURE 19. Flow Chart for Auto-Zero Routine

3D00 3E90 MVI 90

3D02 D3E7 Out Control Port ; Program PPI

3D04 2601 MVI H 01 Auto-Zero Subroutine

3D06 7C MOV A,H

3D07 D3E6 OUT C ; Close SW1 open SW2

3D09 0680 MVI B 80 ; Initialize SAR bit pointer

3D0B 3E7F MVI A 7F ; Initialize SAR code

3D0D 4F MOV C,A Return

3D0E D3E5 OUT B ; Port B 4SAR code

3D10 31AA3D LXI SP 3DAA Start ; Dimension stack pointer

3D13 D3E4 OUT A ; Start A/D

3D15 FB IE

3D16 00 NOP Loop ; Loop until INT asserted

3D17 C3163D JMP Loop

3D1A 7A MOV A,D Auto-Zero

3D1B C600 ADI 00

3D1D CA2D3D JZ Set C ; Test A/D output data for zero

3D20 78 MOV A,B Shift B

3D21 F600 ORI 00 ; Clear carry

3D23 1F RAR ; Shift ‘1‘ in B right one place

3D24 FE00 CPI 00 ; Is B zero? If yes last

3D26 CA373D JZ Done ; approximation has been made

3D29 47 MOV B,A

3D2A C3333D JMP New C

3D2D 79 MOV A,C Set C

3D2E B0 ORA B ; Set bit in C that is in same

3D2F 4F MOV C,A ; position as ‘1‘ in B

3D30 C3203D JMP Shift B

3D33 A9 XRA C New C ; Clear bit in C that is in

3D34 C30D3D JMP Return ; same position as ‘1‘ in B

3D37 47 MOV B,A Done ; then output new SAR code.

3D38 7C MOV A,H ; Open SW1, close SW2 then

3D39 EE03 XRI 03 ; proceed with program. Preamp

3D3B D3E6 OUT C ; is now zeroed.

3D3D #Normal

Program for processing

proper data values

3C3D DBE4 IN A Read A/D Subroutine ; Read A/D data

3C3F EEFF XRI FF ; Invert data

3C41 57 MOV D,A

3C42 78 MOV A,B ; Is B Reg 40? If not stay

3C43 E6FF ANI FF ; in auto zero subroutine

3C45 C21A3D JNZ Auto-Zero

3C48 C33D3D JMP Normal

Note: All numerical values are hexadecimal representations.

FIGURE 20. Software for Auto-Zeroed Differential A/D

5.3 Multiple A/D Converters in a Z-80ÉInterrupt Driven

Mode (Continued)

The following notes apply:

1) It is assumed that the CPU automatically performs a RST

7 instruction when a valid interrupt is acknowledged (CPU

is in interrupt mode 1). Hence, the subroutine starting ad-

dress of X0038.

2) The address bus from the Z-80 and the data bus to the Z-

80 are assumed to be inverted by bus drivers.

3) A/D data and identifying words will be stored in sequen-

tial memory locations starting at the arbitrarily chosen ad-

dress X 3E00.

4) The stack pointer must be dimensioned in the main pro-

gram as the RST 7 instruction automatically pushes the

PC onto the stack and the subroutine uses an additional

6 stack addresses.

5) The peripherals of concern are mapped into I/O space

with the following port assignments:

HEX PORT ADDRESS PERIPHERAL

00 MM74C374 8-bit flip-flop

01 A/D 1

02 A/D 2

03 A/D 3

04 A/D 4

05 A/D 5

06 A/D 6

07 A/D 7

This port address also serves as the A/D identifying word in

the program.

TL/H/5671–29

FIGURE 21. Multiple A/Ds with Z-80 Type Microprocessor

INTERRUPT SERVICING SUBROUTINE

SOURCE

LOC OBJ CODE STATEMENT COMMENT

0038 E5 PUSH HL ; Save contents of all registers affected by

0039 C5 PUSH BC ; this subroutine.

003A F5 PUSH AF ; Assumed INT mode 1 earlier set.

003B 21 00 3E LD (HL),X3E00 ; Initialize memory pointer where data will be stored.

003E 0E 01 LD C, X01 ; C register will be port ADDR of A/D converters.

0040 D300 OUT X00, A ; Load peripheral status word into 8-bit latch.

0042 DB00 IN A, X00 ; Load status word into accumulator.

0044 47 LD B,A ; Save the status word.

0045 79 TEST LD A,C ; Test to see if the status of all A/D’s have

0046 FE 08 CP, X08 ; been checked. If so, exit subroutine

0048 CA 60 00 JPZ, DONE

004B 78 LD A,B ; Test a single bit in status word by looking for

004C 1F RRA ; a ‘1‘ to be rotated into the CARRY (an INT

004D 47 LD B,A ; is loaded as a ‘1‘). If CARRY is set then load

004E DA 5500 JPC, LOAD ; contents of A/D at port ADDR in C register.

0051 0C NEXT INC C ; If CARRY is not set, increment C register to point

0052 C3 4500 JP,TEST ; to next A/D, then test next bit in status word.

0055 ED 78 LOAD IN A, (C) ; Read data from interrupting A/D and invert

0057 EE FF XOR FF ; the data.

0059 77 LD (HL),A ; Store the data

005A 2C INC L

005B 71 LD (HL),C ; Store A/D identifier (A/D port ADDR).

005C 2C INC L

005D C3 51 00 JP,NEXT ; Test next bit in status word.

0060 F1 DONE POP AF ; Re-establish all registers as they were

0061 C1 POP BC ; before the interrupt.

0062 E1 POP HL

0063 C9 RET ; Return to original program

Ordering Information

TEMP RANGE 0§CTO70

CTO70

40§CTOa

85§C

g(/4 Bit ADC0801LCN

Adjusted

ERROR g(/2 Bit ADC0802LCWM ADC0802LCV ADC0802LCN

Unadjusted

g(/2 Bit ADC0803LCWM ADC0803LCV ADC0803LCN

Adjusted

g1Bit ADC0804LCWM ADC0804LCV ADC0804LCN ADC0805LCN

Unadjusted

PACKAGE OUTLINE M20BÐSmall Outline V20AÐChip Carrier N20AÐMolded DIP

TEMP RANGE b40§CTOa

85§Cb55§CTOa

125§C

g(/4 Bit Adjusted ADC0801LCJ ADC0801LJ

ERROR g(/2 Bit Unadjusted ADC0802LCJ ADC0802LJ,

g(/2 Bit Adjusted ADC0803LCJ ADC0802LJ/883

g1Bit Unadjusted ADC0804LCJ

PACKAGE OUTLINE J20AÐCavity DIP J20AÐCavity DIP

Connection Diagrams

ADC080X

Dual-In-Line and Small Outline (SO) Packages

TL/H/5671–30

ADC080X

Molded Chip Carrier (PCC) Package

TL/H/5671–32

See Ordering Information

Physical Dimensions inches (millimeters)

Dual-In-Line Package (J)

Order Number ADC0801LJ, ADC0802LJ, ADC0801LCJ,

ADC0802LCJ, ADC0803LCJ or ADC0804LCJ

ADC0802LJ/883 or 5962-9096601MRA

NS Package Number J20A

SO Package (M)

Order Number ADC0802LCWM, ADC0803LCWM or ADC0804LCWM

NS Package Number M20B

Physical Dimensions inches (millimeters) (Continued)

Molded Dual-In-Line Package (N)

Order Number ADC0801LCN, ADC0802LCN,

ADC0803LCN, ADC0804LCN or ADC0805LCN

NS Package Number N20A

ADC0801/ADC0802/ADC0803/ADC0804/ADC0805

8-Bit mP Compatible A/D Converters

Physical Dimensions inches (millimeters) (Continued)

Molded Chip Carrier Package (V)

Order Number ADC0802LCV, ADC0803LCV or ADC0804LCV

NS Package Number V20A

LIFE SUPPORT POLICY

NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT

DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL

SEMICONDUCTOR CORPORATION. As used herein:

1. Life support devices or systems are devices or 2. A critical component is any component of a life

systems which, (a) are intended for surgical implant support device or system whose failure to perform can

into the body, or (b) support or sustain life, and whose be reasonably expected to cause the failure of the life

failure to perform, when properly used in accordance support device or system, or to affect its safety or

with instructions for use provided in the labeling, can effectiveness.

be reasonably expected to result in a significant injury

to the user.

National Semiconductor National Semiconductor National Semiconductor National Semiconductor

Corporation Europe Hong Kong Ltd. Japan Ltd.

1111 West Bardin Road Fax: (

49) 0-180-530 85 86 13th Floor, Straight Block, Tel: 81-043-299-2309

Arlington, TX 76017 Email: cnjwge

tevm2.nsc.com Ocean Centre, 5 Canton Rd. Fax: 81-043-299-2408

Tel: 1(800) 272-9959 Deutsch Tel: (

49) 0-180-530 85 85 Tsimshatsui, Kowloon

Fax: 1(800) 737-7018 English Tel: (

49) 0-180-532 78 32 Hong Kong

Fran3ais Tel: (

49) 0-180-532 93 58 Tel: (852) 2737-1600

Italiano Tel: (

49) 0-180-534 16 80 Fax: (852) 2736-9960

National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.