Product
Folder
Order
Now
Technical
Documents
Tools &
Software
Support &
Community
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM2576
,
LM2576HV
SNVS107E –JUNE 1999–REVISED JUNE 2020
LM2576xx Series SIMPLE SWITCHER
®
3-A Step-Down Voltage Regulator
1
1 Features
1• New product available: LMR33630 36-V, 3-A, 400-
kHz synchronous converter
• 3.3-V, 5-V, 12-V, 15-V, and adjustable output
versions
• Adjustable version output voltage range: 1.23 V to
37 V (57 V for HV version) ±4% maximum over
line and load conditions
• Specified 3-A output current
• Wide input voltage range: 40 V Up to 60 V for HV
version
• Requires only four external components
• 52-kHz Fixed-frequency internal oscillator
• TTL-shutdown capability, low-power standby
mode
• High efficiency
• Uses readily available standard inductors
• Thermal shutdown and current limit protection
• Create a Custom Design with WEBENCH Tools
2 Applications
•Motor drives
•Merchant network and server PSU
•Appliances
•Test and measurement equipment
3 Description
The LM2576 series of regulators are monolithic
integrated circuits that provide all the active functions
for a step-down (buck) switching regulator, capable of
driving 3-A load with excellent line and load
regulation. These devices are available in fixed output
voltages of 3.3 V, 5 V, 12 V, 15 V, and an adjustable
output version.
Requiring a minimum number of external
components, these regulators are simple to use and
include fault protection and a fixed-frequency
oscillator.
The LM2576 series offers a high-efficiency
replacement for popular three-terminal linear
regulators. It substantially reduces the size of the
heat sink, and in some cases no heat sink is
required.
A standard series of inductors optimized for use with
the LM2576 are available from several different
manufacturers. This feature greatly simplifies the
design of switch-mode power supplies.
Other features include a ±4% tolerance on output
voltage within specified input voltages and output
load conditions, and ±10% on the oscillator
frequency. External shutdown is included, featuring
50-μA (typical) standby current. The output switch
includes cycle-by-cycle current limiting, as well as
thermal shutdown for full protection under fault
conditions.
The new product, LMR33630, offers reduced BOM
cost, higher efficiency, and an 85% reduction in
solution size among many other features. See the
Device Comparison Table to compare specs. Start a
WEBENCH Design with LMR33630.
Device Information(1)
PART NUMBER PACKAGE BODY SIZE (NOM)
LM2576
LM2576HV TO-220 (5) 10.16 mm × 8.51 mm
DDPAK/TO-263 (5) 10.16 mm × 8.42 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Fixed Output Voltage Version Typical Application Diagram
2
LM2576
,
LM2576HV
SNVS107E –JUNE 1999–REVISED JUNE 2020
www.ti.com
Product Folder Links: LM2576 LM2576HV
Submit Documentation Feedback Copyright © 1999–2020, Texas Instruments Incorporated
Table of Contents
1 Features.................................................................. 1
2 Applications ........................................................... 1
3 Description............................................................. 1
4 Revision History..................................................... 2
5 Pin Configuration and Functions......................... 3
6 Specifications......................................................... 4
6.1 Absolute Maximum Ratings ..................................... 4
6.2 ESD Ratings.............................................................. 4
6.3 Recommended Operating Conditions....................... 4
6.4 Thermal Information.................................................. 4
6.5 Electrical Characteristics: 3.3 V................................ 5
6.6 Electrical Characteristics: 5 V................................... 5
6.7 Electrical Characteristics: 12 V................................. 5
6.8 Electrical Characteristics: 15 V................................. 6
6.9 Electrical Characteristics: Adjustable Output
Voltage....................................................................... 6
6.10 Electrical Characteristics: All Output Voltage
Versions..................................................................... 6
6.11 Typical Characteristics............................................ 8
7 Detailed Description............................................ 12
7.1 Overview................................................................. 12
7.2 Functional Block Diagram....................................... 12
7.3 Feature Description................................................. 12
7.4 Device Functional Modes........................................ 14
8 Application and Implementation ........................ 16
8.1 Application Information............................................ 16
8.2 Typical Applications ................................................ 20
9 Power Supply Recommendations...................... 25
10 Layout................................................................... 26
10.1 Layout Guidelines ................................................. 26
10.2 Layout Example .................................................... 27
10.3 Grounding ............................................................. 27
10.4 Heat Sink and Thermal Considerations................ 27
11 Device and Documentation Support ................. 29
11.1 Device Support .................................................... 29
11.2 Documentation Support ........................................ 30
11.3 Related Links ........................................................ 30
11.4 Support Resources ............................................... 30
11.5 Receiving Notification of Documentation Updates 30
11.6 Trademarks........................................................... 30
11.7 Electrostatic Discharge Caution............................ 30
11.8 Glossary................................................................ 31
12 Mechanical, Packaging, and Orderable
Information........................................................... 31
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision D (May 2016) to Revision E Page
• Added information about the LMR33630 ............................................................................................................................... 1
Changes from Revision C (April 2013) to Revision D Page
• Added ESD Ratings table, Feature Description section, Device Functional Modes,Application and Implementation
section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and
Mechanical, Packaging, and Orderable Information section.................................................................................................. 1
• Moved the thermal resistance data from the Electrical Characteristics: All Output Voltage Versions table to the
Thermal Information table....................................................................................................................................................... 4
Changes from Revision B (April 2013) to Revision C Page
• Changed layout of National Data Sheet to TI format ............................................................................................................. 3
3
LM2576
,
LM2576HV
www.ti.com
SNVS107E –JUNE 1999–REVISED JUNE 2020
Product Folder Links: LM2576 LM2576HV
Submit Documentation FeedbackCopyright © 1999–2020, Texas Instruments Incorporated
5 Pin Configuration and Functions
KC Package
5-Pin TO-220
Top View
KTT Package
5-PIN DDPAK/TO-263
Top View DDPAK/TO-263 (S) Package
5-Lead Surface-Mount Package
Top View
(1) I = INPUT, O = OUTPUT
Pin Functions
PIN I/O(1) DESCRIPTION
NO. NAME
1 VIN ISupply input pin to collector pin of high-side transistor. Connect to power supply and input
bypass capacitors CIN. Path from VIN pin to high-frequency bypass CIN and GND must be as
short as possible.
2 OUTPUT O Emitter pin of the power transistor. This is a switching node. Attach this pin to an inductor
and the cathode of the external diode.
3 GROUND — Ground pin. Path to CIN must be as short as possible.
4 FEEDBACK I Feedback sense input pin. Connect to the midpoint of feedback divider to set VOUT for ADJ
version or connect this pin directly to the output capacitor for a fixed output version.
5 ON/OFF I Enable input to the voltage regulator. High = OFF and low = ON. Connect to GND to enable
the voltage regulator. Do not leave this pin float.
— TAB — Connected to GND. Attached to heatsink for thermal relief for TO-220 package or put a
copper plane connected to this pin as a thermal relief for DDPAK package.
4
LM2576
,
LM2576HV
SNVS107E –JUNE 1999–REVISED JUNE 2020
www.ti.com
Product Folder Links: LM2576 LM2576HV
Submit Documentation Feedback Copyright © 1999–2020, Texas Instruments Incorporated
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) If Military/Aerospace specified devices are required, please contact the TI Sales Office/ Distributors for availability and specifications.
6 Specifications
6.1 Absolute Maximum Ratings
over the recommended operating junction temperature range of -40°C to 125°C (unless otherwise noted)(1)(2)
MIN MAX UNIT
Maximum supply voltage LM2576 45 V
LM2576HV 63
ON /OFF pin input voltage −0.3V ≤V≤+VIN V
Output voltage to ground (Steady-state) −1 V
Power dissipation Internally Limited
Maximum junction temperature, TJ150 °C
Storage temperature, Tstg −65 150 °C
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
6.2 ESD Ratings VALUE UNIT
V(ESD) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±2000 V
6.3 Recommended Operating Conditions
over the recommended operating junction temperature range of -40°C to 125°C (unless otherwise noted)
MIN MAX UNIT
Temperature LM2576, LM2576HV −40 125 °C
Supply voltage LM2576 40 V
LM2576HV 60
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953 and the Using New Thermal Metrics applications report, SBVA025.
(2) The package thermal impedance is calculated in accordance with JESD 51-7
(3) Thermal Resistances were simulated on a 4-layer, JEDEC board.
6.4 Thermal Information
THERMAL METRIC(1)(2)(3) LM2576, LM2576HV
UNITKTT (TO-263) KC (TO-220)
5 PINS 5 PINS
RθJA Junction-to-ambient thermal resistance 42.6 32.4 °C/W
RθJC(top) Junction-to-case (top) thermal resistance 43.3 41.2 °C/W
RθJB Junction-to-board thermal resistance 22.4 17.6 °C/W
ψJT Junction-to-top characterization parameter 10.7 7.8 °C/W
ψJB Junction-to-board characterization parameter 21.3 17 °C/W
RθJC(bot) Junction-to-case (bottom) thermal resistance 0.4 0.4 °C/W
5
LM2576
,
LM2576HV
www.ti.com
SNVS107E –JUNE 1999–REVISED JUNE 2020
Product Folder Links: LM2576 LM2576HV
Submit Documentation FeedbackCopyright © 1999–2020, Texas Instruments Incorporated
(1) External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance.
When the LM2576/LM2576HV is used as shown in Figure 26 and Figure 32, system performance is as shown in Electrical
Characteristics: All Output Voltage Versions.
6.5 Electrical Characteristics: 3.3 V
Specifications are for TJ= 25°C (unless otherwise noted).
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SYSTEM PARAMETERS TEST CIRCUIT Figure 26 and Figure 32(1)
VOUT
Output Voltage VIN = 12 V, ILOAD = 0.5 A
Circuit of Figure 26 and Figure 32 3.234 3.3 3.366 V
Output Voltage: LM2576 6 V ≤VIN ≤40 V, 0.5 A ≤
ILOAD ≤3 A
Circuit of Figure 26 and
Figure 32
TJ= 25°C 3.168 3.3 3.432
V
Applies over full
operating
temperature range 3.135 3.465
Output Voltage: LM2576HV 6 V ≤VIN ≤60 V, 0.5 A ≤
ILOAD ≤3 A
Circuit of Figure 26 and
Figure 32
TJ= 25°C 3.168 3.3 3.45
V
Applies over full
operating
temperature range 3.135 3.482
ηEfficiency VIN = 12 V, ILOAD = 3 A 75%
(1) External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance.
When the LM2576/LM2576HV is used as shown in Figure 26 and Figure 32, system performance is as shown in Electrical
Characteristics: All Output Voltage Versions.
6.6 Electrical Characteristics: 5 V
Specifications are for TJ= 25°C for the Figure 26 and Figure 32 (unless otherwise noted).
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SYSTEM PARAMETERS TEST CIRCUIT Figure 26 and Figure 32(1)
VOUT Output Voltage VIN = 12 V, ILOAD = 0.5 A
Circuit of Figure 26 and Figure 32 4.9 5 5.1 V
VOUT Output Voltage
LM2576
0.5 A ≤ILOAD ≤3 A,
8 V ≤VIN ≤40 V
Circuit of Figure 26 and
Figure 32
TJ= 25°C 4.8 5 5.2
V
Applies over full
operating
temperature range 4.75 5.25
VOUT Output Voltage
LM2576HV
0.5 A ≤ILOAD ≤3 A,
8 V ≤VIN ≤60 V
Circuit of Figure 26 and
Figure 32
TJ= 25°C 4.8 5 4.75
V
Applies over full
operating
temperature range 5.225 5.275
ηEfficiency VIN = 12 V, ILOAD = 3 A 77%
(1) External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance.
When the LM2576/LM2576HV is used as shown in Figure 26 and Figure 32, system performance is as shown in Electrical
Characteristics: All Output Voltage Versions.
6.7 Electrical Characteristics: 12 V
Specifications are for TJ= 25°C (unless otherwise noted).
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SYSTEM PARAMETERS TEST CIRCUIT Figure 26 and Figure 32(1)
VOUT Output Voltage VIN = 25 V, ILOAD = 0.5 A
Circuit of Figure 26 and Figure 32 11.76 12 12.24 V
VOUT Output Voltage
LM2576
0.5 A ≤ILOAD ≤3 A,
15 V ≤VIN ≤40 V
Circuit of Figure 26 and
Figure 32 and
TJ= 25°C 11.52 12 12.48
V
Applies over full
operating
temperature range 11.4 12.6
VOUT Output Voltage
LM2576HV
0.5 A ≤ILOAD ≤3 A,
15 V ≤VIN ≤60 V
Circuit of Figure 26 and
Figure 32
TJ= 25°C 11.52 12 12.54
V
Applies over full
operating
temperature range 11.4 12.66
ηEfficiency VIN = 15 V, ILOAD = 3 A 88%
6
LM2576
,
LM2576HV
SNVS107E –JUNE 1999–REVISED JUNE 2020
www.ti.com
Product Folder Links: LM2576 LM2576HV
Submit Documentation Feedback Copyright © 1999–2020, Texas Instruments Incorporated
(1) External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance.
When the LM2576/LM2576HV is used as shown in Figure 26 and Figure 32, system performance is as shown in Electrical
Characteristics: All Output Voltage Versions.
6.8 Electrical Characteristics: 15 V
over operating free-air temperature range (unless otherwise noted).
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SYSTEM PARAMETERS TEST CIRCUIT Figure 26 and Figure 32(1)
VOUT Output Voltage VIN = 25 V, ILOAD = 0.5 A
Circuit of Figure 26 and Figure 32 14.7 15 15.3 V
VOUT Output Voltage
LM2576
0.5 A ≤ILOAD ≤3 A,
18 V ≤VIN ≤40 V
Circuit of Figure 26 and
Figure 32
TJ= 25°C 14.4 15 15.6
V
Applies over full
operating
temperature range 14.25 15.75
VOUT Output Voltage
LM2576HV
0.5 A ≤ILOAD ≤3 A,
18 V ≤VIN ≤60 V
Circuit of Figure 26 and
Figure 32
TJ= 25°C 14.4 15 14.25
V
Applies over full
operating
temperature range 15.68 15.83
ηEfficiency VIN = 18 V, ILOAD = 3 A 88%
(1) External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance.
When the LM2576/LM2576HV is used as shown in Figure 26 and Figure 32, system performance is as shown in Electrical
Characteristics: All Output Voltage Versions.
6.9 Electrical Characteristics: Adjustable Output Voltage
over operating free-air temperature range (unless otherwise noted).
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SYSTEM PARAMETERS TEST CIRCUIT Figure 26 and Figure 32(1)
VOUT Feedback voltage VIN = 12 V, ILOAD = 0.5 A
VOUT = 5 V,
Circuit of Figure 26 and Figure 32 1.217 1.23 1.243 V
VOUT Feedback Voltage
LM2576
0.5 A ≤ILOAD ≤3 A,
8 V ≤VIN ≤40 V
VOUT = 5 V, Circuit of
Figure 26 and Figure 32
TJ= 25°C 1.193 1.23 1.267
V
Applies over full
operating
temperature range 1.18 1.28
VOUT Feedback Voltage
LM2576HV
0.5 A ≤ILOAD ≤3 A,
8 V ≤VIN ≤60 V
VOUT = 5 V, Circuit of
Figure 26 and Figure 32
TJ= 25°C 1.193 1.23 1.273
V
Applies over full
operating
temperature range 1.18 1.286
ηEfficiency VIN = 12 V, ILOAD = 3 A, VOUT = 5 V 77%
(1) All limits specified at room temperature (25°C) unless otherwise noted. All room temperature limits are 100% production tested. All limits
at temperature extremes are specified through correlation using standard Statistical Quality Control (SQC) methods.
(2) External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance.
When the LM2576/LM2576HV is used as shown in Figure 26 and Figure 32, system performance is as shown in Electrical
Characteristics: All Output Voltage Versions.
(3) The oscillator frequency reduces to approximately 11 kHz in the event of an output short or an overload which causes the regulated
output voltage to drop approximately 40% from the nominal output voltage. This self protection feature lowers the average power
dissipation of the IC by lowering the minimum duty cycle from 5% down to approximately 2%.
6.10 Electrical Characteristics: All Output Voltage Versions
over operating free-air temperature range (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP(1) MAX UNIT
SYSTEM PARAMETERS TEST CIRCUIT Figure 26 and Figure 32(2)
IbFeedback Bias Current VOUT = 5 V (Adjustable
Version Only)
TJ= 25°C 100 50
nA
Applies over full
operating
temperature range 500
fOOscillator Frequency(3) TJ= 25°C 47 52 58 kHz
Applies over full operating temperature range 42 63
7
LM2576
,
LM2576HV
www.ti.com
SNVS107E –JUNE 1999–REVISED JUNE 2020
Product Folder Links: LM2576 LM2576HV
Submit Documentation FeedbackCopyright © 1999–2020, Texas Instruments Incorporated
Electrical Characteristics: All Output Voltage Versions (continued)
over operating free-air temperature range (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP(1) MAX UNIT
(4) Output pin sourcing current. No diode, inductor or capacitor connected to output.
(5) Feedback pin removed from output and connected to 0V.
(6) Feedback pin removed from output and connected to +12 V for the Adjustable, 3.3-V, and 5-V versions, and +25 V for the 12-V and 15-
V versions, to force the output transistor OFF.
(7) VIN = 40 V (60 V for high voltage version).
VSAT Saturation Voltage IOUT = 3 A (4)
TJ= 25°C 1.4 1.8
V
Applies over full
operating
temperature range 2
DC Max Duty Cycle (ON)(5) 93% 98%
ICL Current Limit(4)(3) TJ= 25°C 4.2 5.8 6.9 A
Applies over full operating temperature range 3.5 7.5
ILOutput Leakage Current Output = 0 V
Output = −1 V
Output = −1 V (6)(7) 2 7.5 30 mA
IQQuiescent Current(6) 5 10 mA
ISTBY Standby Quiescent
Current ON /OFF Pin = 5 V (OFF) 50 200 μA
ON /OFF CONTROL TEST CIRCUIT Figure 26 and Figure 32
VIH
ON /OFF Pin
Logic Input Level
VOUT = 0 V TJ= 25°C 2.2 1.4
V
Applies over full
operating
temperature range 2.4
VIL
VOUT = Nominal Output
Voltage TJ= 25°C 1.2 1
V
Applies over full
operating
temperature range 0.8
IIH ON /OFF Pin Input
Current ON /OFF Pin = 5 V (OFF) 12 30 μA
IIL ON /OFF Pin = 0 V (ON) 0 10 μA
8
LM2576
,
LM2576HV
SNVS107E –JUNE 1999–REVISED JUNE 2020
www.ti.com
Product Folder Links: LM2576 LM2576HV
Submit Documentation Feedback Copyright © 1999–2020, Texas Instruments Incorporated
6.11 Typical Characteristics
(Circuit of Figure 26 and Figure 32)
Figure 1. Normalized Output Voltage Figure 2. Line Regulation
Figure 3. Dropout Voltage Figure 4. Current Limit
Figure 5. Quiescent Current Figure 6. Standby Quiescent Current
9
LM2576
,
LM2576HV
www.ti.com
SNVS107E –JUNE 1999–REVISED JUNE 2020
Product Folder Links: LM2576 LM2576HV
Submit Documentation FeedbackCopyright © 1999–2020, Texas Instruments Incorporated
Typical Characteristics (continued)
(Circuit of Figure 26 and Figure 32)
Figure 7. Oscillator Frequency Figure 8. Switch Saturation Voltage
Figure 9. Efficiency Figure 10. Minimum Operating Voltage
Figure 11. Quiescent Current versus Duty Cycle Figure 12. Feedback Voltage versus Duty Cycle
10
LM2576
,
LM2576HV
SNVS107E –JUNE 1999–REVISED JUNE 2020
www.ti.com
Product Folder Links: LM2576 LM2576HV
Submit Documentation Feedback Copyright © 1999–2020, Texas Instruments Incorporated
Typical Characteristics (continued)
(Circuit of Figure 26 and Figure 32)
Figure 13. Minimum Operating Voltage Figure 14. Quiescent Current versus Duty Cycle
Figure 15. Feedback Voltage versus Duty Cycle Figure 16. Feedback Pin Current
If the DDPAK/TO-263 package is used, the thermal resistance can be
reduced by increasing the PCB copper area thermally connected to
the package. Using 0.5 square inches of copper area, θJA is 50°C/W,
with 1 square inch of copper area, θJA is 37°C/W, and with 1.6 or
more square inches of copper area, θJA is 32°C/W.
Figure 17. Maximum Power Dissipation (DDPAK/TO-263)
VOUT = 15 V
A: Output Pin Voltage, 50 V/div
B: Output Pin Current, 2 A/div
C: Inductor Current, 2 A/div
D: Output Ripple Voltage, 50 mV/div,
AC-Coupled
Horizontal Time Base: 5 μs/div
Figure 18. Switching Waveforms
R1
1 k
+
±
1.23 V
BAND-GAP
REFERENCE
52 kHZ
OSCILLATOR
+
±
RESET THERMAL
SHUTDOWN
CURRENT
LIMIT
Driver
R2
4
1Internal
Rgulator ON/OFF 5
2
3
D1 COUT
+
CIN
+
regulated
DC Input
VIN
Feedback
VOUT
OUTPUT L1
GND
3 Amp
Switch
Comparator
Fixed Gain
Error Amp
ON/OFF
L
O
A
D
12
LM2576
,
LM2576HV
SNVS107E –JUNE 1999–REVISED JUNE 2020
www.ti.com
Product Folder Links: LM2576 LM2576HV
Submit Documentation Feedback Copyright © 1999–2020, Texas Instruments Incorporated
7 Detailed Description
7.1 Overview
The LM2576 SIMPLE SWITCHER regulator is an easy-to-use, non-synchronous step-down DC-DC converter
with a wide input voltage range from 40 V to up to 60 V for the HV version. It is capable of delivering up to 3-A
DC load current with excellent line and load regulation. These devices are available in fixed output voltages of
3.3 V, 5 V, 12 V, 15 V, and an adjustable output version. The family requires few external components, and the
pin arrangement was designed for simple, optimal PCB layout.
7.2 Functional Block Diagram
3.3 V R2 = 1.7 k
5 V, R2 = 3.1 k
12 V, R2 = 8.84 k
15 V, R2 = 11.3 k
For ADJ. Version
R1 = Open, R2 = 0 Ω
Patent Pending
7.3 Feature Description
7.3.1 Undervoltage Lockout
In some applications, it is desirable to keep the regulator off until the input voltage reaches a certain threshold.
Figure 20 shows an undervoltage lockout circuit that accomplishes this task, while Figure 21 shows the same
circuit applied to a buck-boost configuration. These circuits keep the regulator off until the input voltage reaches
a predetermined level.
VTH ≈VZ1 + 2VBE(Q1) (1)
R1
20 k 20 k
R2
10 k
Q1
+
CIN
+VIN LM2576-XX
3
+VIN
1
5ON/OFF
Z1
-VOUT
GND
R1
20 k 20 k
R2
10 k
Q1
+
CIN
+VIN LM2576-XX
GND3
+VIN
1
5ON/OFF
Z1
13
LM2576
,
LM2576HV
www.ti.com
SNVS107E –JUNE 1999–REVISED JUNE 2020
Product Folder Links: LM2576 LM2576HV
Submit Documentation FeedbackCopyright © 1999–2020, Texas Instruments Incorporated
Feature Description (continued)
Complete circuit not shown.
Figure 20. Undervoltage Lockout for Buck Circuit
Complete circuit not shown (see Figure 24).
Figure 21. Undervoltage Lockout
for Buck-Boost Circuit
7.3.2 Delayed Start-Up
The ON/OFF pin can be used to provide a delayed start-up feature as shown in Figure 22. With an input voltage
of 20 V and for the part values shown, the circuit provides approximately 10 ms of delay time before the circuit
begins switching. Increasing the RC time constant can provide longer delay times, but excessively large RC time
constants can cause problems with input voltages that are high in 60-Hz or 120-Hz ripple, by coupling the ripple
into the ON/OFF pin.
7.3.3 Adjustable Output, Low-Ripple Power Supply
Figure 23 shows a 3-A power supply that features an adjustable output voltage. An additional LC filter that
reduces the output ripple by a factor of 10 or more is included in this circuit.
LM2576HV-ADJ
5
+VIN
1
3GND
100 …F
+
CIN
ON/OFF
2000 …F
COUT
+
D1
1N5822
R2
50 k
R1
1.21 k
100 …F
C1+
Output
Voltage
+1.2 to 50 V
@3A
Output L1
150 µH
2
Feedback
4
20 µH
55 V
Unregulated
DC Input
optional output ripple filter
47 K
+
+VIN LM2576-XX
3
+VIN
1
5ON/OFF GND
0.1 …F
RD
100 …F
+
CIN
CD
14
LM2576
,
LM2576HV
SNVS107E –JUNE 1999–REVISED JUNE 2020
www.ti.com
Product Folder Links: LM2576 LM2576HV
Submit Documentation Feedback Copyright © 1999–2020, Texas Instruments Incorporated
Feature Description (continued)
Complete circuit not shown.
Figure 22. Delayed Start-Up
Figure 23. 1.2-V to 55-V Adjustable 3-A Power Supply With Low Output Ripple
7.4 Device Functional Modes
7.4.1 Shutdown Mode
The ON/OFF pin provides electrical ON and OFF control for the LM2576. When the voltage of this pin is higher
than 1.4 V, the device is in shutdown mode. The typical standby current in this mode is 50 μA.
7.4.2 Active Mode
When the voltage of the ON/OFF pin is below 1.2 V, the device starts switching, and the output voltage rises until
it reaches the normal regulation voltage.
7.4.3 Current Limit
The LM2576 device has current limiting to prevent the switch current from exceeding safe values during an
accidental overload on the output. This current limit value can be found in the Electrical Characteristics: All
Output Voltage Versions under the heading of ICL.
15
LM2576
,
LM2576HV
www.ti.com
SNVS107E –JUNE 1999–REVISED JUNE 2020
Product Folder Links: LM2576 LM2576HV
Submit Documentation FeedbackCopyright © 1999–2020, Texas Instruments Incorporated
Device Functional Modes (continued)
The LM2576 uses cycle-by-cycle peak current limit for overload protection. This helps prevent damage to the
device and external components. The regulator operates in current limit mode whenever the inductor current
exceeds the value of ICL given in the Electrical Characteristics: All Output Voltage Versions. This occurs if the
load current is greater than 3 A or the converter is starting up. Keep in mind that the maximum available load
current depends on the input voltage, output voltage, and inductor value. The regulator also incorporates short-
circuit protection to prevent inductor current run-away. When the voltage on the FB pin (ADJ) falls below about
0.58 V, the switching frequency is dropped to about 11 kHz. This allows the inductor current to ramp down
sufficiently during the switch OFF-time to prevent saturation.
16
LM2576
,
LM2576HV
SNVS107E –JUNE 1999–REVISED JUNE 2020
www.ti.com
Product Folder Links: LM2576 LM2576HV
Submit Documentation Feedback Copyright © 1999–2020, Texas Instruments Incorporated
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
8.1.1 Input Capacitor (CIN)
To maintain stability, the regulator input pin must be bypassed with at least a 100-μF electrolytic capacitor. The
leads of the capacitor must be kept short and placed near the regulator.
If the operating temperature range includes temperatures below −25°C, the input capacitor value may need to be
larger. With most electrolytic capacitors, the capacitance value decreases and the ESR increases with lower
temperatures and age. Paralleling a ceramic or solid tantalum capacitor increases the regulator stability at cold
temperatures. For maximum capacitor operating lifetime, the RMS ripple current rating of the capacitor must be
greater than:
(2)
8.1.2 Inductor Selection
All switching regulators have two basic modes of operation: continuous and discontinuous. The difference
between the two types relates to the inductor current, whether it is flowing continuously, or if it drops to zero for a
period of time in the normal switching cycle. Each mode has distinctive operating characteristics, which can
affect the regulator performance and requirements.
The LM2576 (or any of the SIMPLE SWITCHER family) can be used for both continuous and discontinuous
modes of operation.
The inductor value selection guides in Figure 27 through Figure 31 are designed for buck regulator designs of
the continuous inductor current type. When using inductor values shown in the inductor selection guide, the
peak-to-peak inductor ripple current is approximately 20% to 30% of the maximum DC current. With relatively
heavy load currents, the circuit operates in the continuous mode (inductor current always flowing), but under light
load conditions, the circuit is forced to the discontinuous mode (inductor current falls to zero for a period of time).
This discontinuous mode of operation is perfectly acceptable. For light loads (less than approximately 300 mA), it
can be desirable to operate the regulator in the discontinuous mode, primarily because of the lower inductor
values required for the discontinuous mode.
The selection guide chooses inductor values suitable for continuous mode operation, but if the inductor value
chosen is prohibitively high, the designer must investigate the possibility of discontinuous operation.
Inductors are available in different styles such as pot core, toriod, E-frame, bobbin core, and so forth, as well as
different core materials, such as ferrites and powdered iron. The bobbin core is the least expensive type and
consists of wire wrapped on a ferrite rod core. This type of construction makes for an inexpensive inductor;
however, because the magnetic flux is not completely contained within the core, the bobbin core generates more
electromagnetic interference (EMI). This EMI can cause problems in sensitive circuits or can give incorrect scope
readings because of induced voltages in the scope probe.
The inductors listed in the selection chart include ferrite pot core construction for AIE, powdered iron toroid for
Pulse Engineering, and ferrite bobbin core for Renco.
17
LM2576
,
LM2576HV
www.ti.com
SNVS107E –JUNE 1999–REVISED JUNE 2020
Product Folder Links: LM2576 LM2576HV
Submit Documentation FeedbackCopyright © 1999–2020, Texas Instruments Incorporated
Application Information (continued)
An inductor must not operate beyond its maximum-rated current because it can saturate. When an inductor
begins to saturate, the inductance decreases rapidly, and the inductor begins to look mainly resistive (the DC
resistance of the winding), causing the switch current to rise very rapidly. Different inductor types have different
saturation characteristics, and this must be considered when selecting an inductor.
The inductor manufacturer's data sheets include current and energy limits to avoid inductor saturation.
8.1.3 Inductor Ripple Current
When the switcher is operating in continuous mode, the inductor current waveform ranges from a triangular to a
sawtooth type of waveform (depending on the input voltage). For a given input voltage and output voltage, the
peak-to-peak amplitude of this inductor current waveform remains constant. As the load current rises or falls, the
entire sawtooth current waveform also rises or falls. The average DC value of this waveform is equal to the DC
load current (in the buck regulator configuration).
If the load current drops to a low enough level, the bottom of the sawtooth current waveform reaches zero, and
the switcher changes to a discontinuous mode of operation. This is a perfectly acceptable mode of operation.
Any buck switching regulator (no matter how large the inductor value is) is forced to run discontinuous if the load
current is light enough.
8.1.4 Output Capacitor
An output capacitor is required to filter the output voltage and is needed for loop stability. The capacitor must be
placed near the LM2576 using short PCB traces. Standard aluminum electrolytics are usually adequate, but TI
recommends low ESR types for low output ripple voltage and good stability. The ESR of a capacitor depends on
many factors, including: the value, the voltage rating, physical size, and the type of construction. In general, low
value or low voltage (less than 12 V) electrolytic capacitors usually have higher ESR numbers.
The amount of output ripple voltage is primarily a function of the ESR (Equivalent Series Resistance) of the
output capacitor and the amplitude of the inductor ripple current (ΔIIND). See the Inductor Ripple Current section.
The lower capacitor values (220 μF to 1000 μF) allows typically 50 mV to 150 mV of output ripple voltage, while
larger-value capacitors reduces the ripple to approximately 20 mV to 50 mV.
Output Ripple Voltage = (ΔIIND)(ESR of COUT) (3)
To further reduce the output ripple voltage, several standard electrolytic capacitors can be paralleled or a higher-
grade capacitor can be used. Such capacitors are often called high-frequency,low-inductance, or low-ESR.
These reduces the output ripple to 10 mV or 20 mV. However, when operating in the continuous mode, reducing
the ESR below 0.03 Ωcan cause instability in the regulator.
Tantalum capacitors can have a very low ESR, and must be carefully evaluated if it is the only output capacitor.
Because of their good low temperature characteristics, a tantalum can be used in parallel with aluminum
electrolytics, with the tantalum making up 10% or 20% of the total capacitance.
The ripple current rating of the capacitor at 52 kHz must be at least 50% higher than the peak-to-peak inductor
ripple current.
8.1.5 Catch Diode
Buck regulators require a diode to provide a return path for the inductor current when the switch is off. This diode
must be placed close to the LM2576 using short leads and short printed-circuit traces.
Because of their fast switching speed and low forward voltage drop, Schottky diodes provide the best efficiency,
especially in low output voltage switching regulators (less than 5 V). Fast-recovery, high-efficiency, or ultra-fast
recovery diodes are also suitable, but some types with an abrupt turnoff characteristic can cause instability and
EMI problems. A fast-recovery diode with soft recovery characteristics is a better choice. Standard 60-Hz diodes
(for example, 1N4001 or 1N5400, and so forth) are also not suitable. See Table 3 for a Schottky and soft fast-
recovery diode selection guide.
18
LM2576
,
LM2576HV
SNVS107E –JUNE 1999–REVISED JUNE 2020
www.ti.com
Product Folder Links: LM2576 LM2576HV
Submit Documentation Feedback Copyright © 1999–2020, Texas Instruments Incorporated
Application Information (continued)
8.1.6 Output Voltage Ripple and Transients
The output voltage of a switching power supply contains a sawtooth ripple voltage at the switcher frequency,
typically about 1% of the output voltage, and can also contain short voltage spikes at the peaks of the sawtooth
waveform.
The output ripple voltage is due mainly to the inductor sawtooth ripple current multiplied by the ESR of the output
capacitor (see the Inductor Selection section).
The voltage spikes are present because of the fast switching action of the output switch, and the parasitic
inductance of the output filter capacitor. To minimize these voltage spikes, special low inductance capacitors can
be used, and their lead lengths must be kept short. Wiring inductance, stray capacitance, and the scope probe
used to evaluate these transients all contribute to the amplitude of these spikes.
An additional small LC filter (20 μH and 100 μF) can be added to the output (as shown in Figure 23) to further
reduce the amount of output ripple and transients. A 10× reduction in output ripple voltage and transients is
possible with this filter.
8.1.7 Feedback Connection
The LM2576 (fixed voltage versions) feedback pin must be wired to the output voltage point of the switching
power supply. When using the adjustable version, physically locate both output voltage programming resistors
near the LM2576 to avoid picking up unwanted noise. Avoid using resistors greater than 100 kΩbecause of the
increased chance of noise pickup.
8.1.8 ON/OFF INPUT
For normal operation, the ON/OFF pin must be grounded or driven with a low-level TTL voltage (typically below
1.6 V). To put the regulator into standby mode, drive this pin with a high-level TTL or CMOS signal. The ON/OFF
pin can be safely pulled up to +VIN without a resistor in series with it. The ON/OFF pin must not be left open.
8.1.9 Inverting Regulator
Figure 24 shows a LM2576-12 in a buck-boost configuration to generate a negative 12-V output from a positive
input voltage. This circuit bootstraps the ground pin of the regulator to the negative output voltage, then by
grounding the feedback pin, the regulator senses the inverted output voltage and regulates it to −12 V.
For an input voltage of 12 V or more, the maximum available output current in this configuration is approximately
700 mA. At lighter loads, the minimum input voltage required drops to approximately 4.7 V.
The switch currents in this buck-boost configuration are higher than in the standard buck-mode design, thus
lowering the available output current. Also, the start-up input current of the buck-boost converter is higher than
the standard buck-mode regulator, and which can overload an input power source with a current limit less than
5 A. Using a delayed turnon or an undervoltage lockout circuit (described in the Negative Boost Regulator
section) allows the input voltage to rise to a high enough level before the switcher would be allowed to turn on.
Because of the structural differences between the buck and the buck-boost regulator topologies, the buck
regulator design procedure section cannot be used to select the inductor or the output capacitor. The
recommended range of inductor values for the buck-boost design is between 68 μH and 220 μH, and the output
capacitor values must be larger than what is normally required for buck designs. Low-input voltages or high-
output currents require a large value output capacitor (in the thousands of micro Farads).
The peak inductor current, which is the same as the peak switch current, can be calculated in Equation 4:
where
• fosc = 52 kHz (4)
Under normal continuous inductor current operating conditions, the minimum VIN represents the worst case.
Select an inductor that is rated for the peak current anticipated.
LM2576-12
2
4
1
3 5
+1N5820
+COUT
2200 PF
Feedback
Output
VIN
CIN
100 PF
GND
100 PH
VOUT = -12 V
-VIN
-5 V to -12 V
LOW ESR
ON/OFF
LM2576HV-ADJ
5
+VIN
1
3GND
100 …F
+CIN
ON/OFF
2200 …F
COUT
+
D1
1N5822
Output L1
68 µH
2
Feedback
4
+12 To +45 V
Unregulated
DC Input
-12 @ 0.7 A
REGULATED
DC INPUT
19
LM2576
,
LM2576HV
www.ti.com
SNVS107E –JUNE 1999–REVISED JUNE 2020
Product Folder Links: LM2576 LM2576HV
Submit Documentation FeedbackCopyright © 1999–2020, Texas Instruments Incorporated
Application Information (continued)
Figure 24. Inverting Buck-Boost Develops −12 V
Also, the maximum voltage appearing across the regulator is the absolute sum of the input and output voltage.
For a −12-V output, the maximum input voltage for the LM2576 is +28 V, or +48 V for the LM2576HV.
8.1.10 Negative Boost Regulator
Another variation on the buck-boost topology is the negative boost configuration. The circuit in Figure 25 accepts
an input voltage ranging from −5 V to −12 V and provides a regulated −12-V output. Input voltages greater than
−12 V causes the output to rise above −12 V, but does not damage the regulator.
Typical Load Current
400 mA for VIN =−5.2 V
750 mA for VIN =−7 V
Heat sink may be required.
Figure 25. Negative Boost
Because of the boosting function of this type of regulator, the switch current is relatively high, especially at low
input voltages. Output load current limitations are a result of the maximum current rating of the switch. Also,
boost regulators cannot provide current-limiting load protection in the event of a shorted load, so some other
means (such as a fuse) can be necessary.
LM2576HV-
Fixed Output
100 …F
COUT
1000 µF
L
O
A
D
+
L1
100 µH
+
CIN
VIN
UNREGULATED
DC INPUT
+VIN
1
GND 3 ON/OFF 5
2
D1
MBR360
VOUT
Feedback
Output
4
20
LM2576
,
LM2576HV
SNVS107E –JUNE 1999–REVISED JUNE 2020
www.ti.com
Product Folder Links: LM2576 LM2576HV
Submit Documentation Feedback Copyright © 1999–2020, Texas Instruments Incorporated
8.2 Typical Applications
8.2.1 Fixed Output Voltage Version
CIN — 100-μF, 75-V, Aluminum Electrolytic
COUT — 1000-μF, 25-V, Aluminum Electrolytic
D1— Schottky, MBR360
L1— 100 μH, Pulse Eng. PE-92108
R1— 2 k, 0.1%
R2— 6.12 k, 0.1%
Figure 26. Fixed Output Voltage Versions
8.2.1.1 Design Requirements
Table 1 lists the design parameters of this example.
Table 1. Design Parameters
DESIGN PARAMETER EXAMPLE VALUE
Regulated Output Voltage
(3.3 V, 5 V, 12 V, or 15 V), VOUT 5 V
Maximum Input Voltage, VIN(Max) 15 V
Maximum Load Current,
ILOAD(Max) 3 A
8.2.1.2 Detailed Design Procedure
8.2.1.2.1 Custom Design with WEBENCH Tools
Click here to create a custom design using the WEBENCH®Power Designer.
1. Start by entering your VIN, VOUT and IOUT requirements.
2. Optimize your design for key parameters like efficiency, footprint and cost using the optimizer dial and
compare this design with other possible solutions from Texas Instruments.
3. WEBENCH Power Designer provides you with a customized schematic along with a list of materials with real
time pricing and component availability.
4. In most cases, you will also be able to:
– Run electrical simulations to see important waveforms and circuit performance,
– Run thermal simulations to understand the thermal performance of your board,
– Export your customized schematic and layout into popular CAD formats,
– Print PDF reports for the design, and share your design with colleagues.
8.2.1.2.2 Inductor Selection (L1)
1. Select the correct Inductor value selection guide from Figure 27,Figure 28,Figure 29,orFigure 30. (Output
21
LM2576
,
LM2576HV
www.ti.com
SNVS107E –JUNE 1999–REVISED JUNE 2020
Product Folder Links: LM2576 LM2576HV
Submit Documentation FeedbackCopyright © 1999–2020, Texas Instruments Incorporated
voltages of 3.3 V, 5 V, 12 V, or 15 V, respectively). For other output voltages, see the design procedure for
the adjustable version. Use the selection guide shown in Figure 28.
2. From the inductor value selection guide, identify the inductance region intersected by VIN(Max) and
ILOAD(Max), and note the inductor code for that region. From the selection guide, the inductance area
intersected by the 15-V line and 3-A line is L100.
3. Identify the inductor value from the inductor code, and select an appropriate inductor from the table shown in
Figure 27. Part numbers are listed for three inductor manufacturers. The inductor chosen must be rated for
operation at the LM2576 switching frequency (52 kHz) and for a current rating of 1.15 × ILOAD. For additional
inductor information, see the Inductor Selection section. Inductor value required is 100 μH from the table in
Figure 27. Choose AIE 415-0930, Pulse Engineering PE92108, or Renco RL2444.
8.2.1.2.3 Output Capacitor Selection (COUT)
1. The value of the output capacitor together with the inductor defines the dominate pole-pair of the switching
regulator loop. For stable operation and an acceptable output ripple voltage, (approximately 1% of the output
voltage) TI recommends a value between 100 μF and 470 μF. COUT = 680-μF to 2000-μF standard aluminum
electrolytic was chosen.
2. The voltage rating of the capacitor must be at least 1.5 times greater than the output voltage. For a 5-V
regulator, a rating of at least 8 V is appropriate, and a 10-V or 15-V rating is recommended. Capacitor
voltage rating = 20 V. Higher voltage electrolytic capacitors generally have lower ESR numbers, and for this
reason, it can be necessary to select a capacitor rated for a higher voltage than would normally be needed.
8.2.1.2.4 Catch Diode Selection (D1)
1. The catch-diode current rating must be at least 1.2 times greater than the maximum load current. Also, if the
power supply design must withstand a continuous output short, the diode must have a current rating equal to
the maximum current limit of the LM2576. The most stressful condition for this diode is an overload or
shorted output condition. For this example, a 3-A current rating is adequate.
2. The reverse voltage rating of the diode must be at least 1.25 times the maximum input voltage. Use a 20-V
1N5823 or SR302 Schottky diode, or any of the suggested fast-recovery diodes shown in Table 3.
8.2.1.2.5 Input Capacitor (CIN)
An aluminum or tantalum electrolytic bypass capacitor located close to the regulator is needed for stable
operation. A 100-μF, 25-V aluminum electrolytic capacitor located near the input and ground pins provides
sufficient bypassing.
8.2.2 Application Curves
Figure 27. LM2576(HV)-3.3 Figure 28. LM2576(HV)-5.0
LM2576HV-
ADJ
100 …F
COUT
1000 µF
L
O
A
D
+
L1
100 µH
+
CIN
7 V ± 60 V
UNREGULATED
DC INPUT
+VIN
1
GND 3 ON/OFF 5
2
D1
MBR360
Feedback
Output
4
R1
R2
VOUT
5 V
22
LM2576
,
LM2576HV
SNVS107E –JUNE 1999–REVISED JUNE 2020
www.ti.com
Product Folder Links: LM2576 LM2576HV
Submit Documentation Feedback Copyright © 1999–2020, Texas Instruments Incorporated
Figure 29. LM2576(HV)-12 Figure 30. LM2576(HV)-15
Figure 31. LM2576(HV)-ADJ
8.2.3 Adjusted Output Voltage Version
where
VREF = 1.23 V, R1 between 1 k and 5 k
Figure 32. Adjustable Output Voltage Version
10 1000
E T 25 10 115 V V
25 52
u u u u
OUT
IN OUT
IN
V1000
E T V V V V
V F in kHz
u u u
23
LM2576
,
LM2576HV
www.ti.com
SNVS107E –JUNE 1999–REVISED JUNE 2020
Product Folder Links: LM2576 LM2576HV
Submit Documentation FeedbackCopyright © 1999–2020, Texas Instruments Incorporated
8.2.3.1 Design Requirements
Table 2 lists the design parameters of this example.
Table 2. Design Parameters
DESIGN PARAMETER EXAMPLE VALUE
Regulated Output Voltage, VOUT 10 V
Maximum Input Voltage, VIN(Max) 25 V
Maximum Load Current,
ILOAD(Max) 3 A
Switching Frequency, F Fixed at 52 kHz
8.2.3.2 Detailed Design Procedure
8.2.3.2.1 Programming Output Voltage
Select R1 and R2, as shown in Figure 32.
Use Equation 5 to select the appropriate resistor values.
(5)
R1can be between 1 k and 5 k. (For best temperature coefficient and stability with time, use 1% metal film
resistors)
(6)
(7)
R2= 1 k (8.13 −1) = 7.13 k, closest 1% value is 7.15 k
8.2.3.2.2 Inductor Selection (L1)
1. Calculate the inductor Volt • microsecond constant, E × T (V × μs), from Equation 8:
(8)
2. Calculate E × T (V × μs):
(9)
3. Use the E • T value from the previous formula and match it with the E × T number on the vertical axis of the
inductor value selection guide shown in Figure 31.
E × T = 115 V × μs (10)
4. On the horizontal axis, select the maximum load current.
ILOAD(Max) = 3 A (11)
5. Identify the inductance region intersected by the E × T value and the maximum load current value. Note the
inductor code for that region. Inductance Region = H150
6. Identify the inductor value from the inductor code, and select an appropriate inductor from the table shown in
Table 4. Part numbers are listed for three inductor manufacturers. The inductor chosen must be rated for
operation at the LM2576 switching frequency (52 kHz) and for a current rating of 1.15 × ILOAD. For additional
inductor information, see the Inductor Selection section. Inductor Value = 150 μH. Choose from AIE part
#415-0936, Pulse Engineering part #PE-531115, or Renco part #RL2445.
8.2.3.2.3 Output Capacitor Selection (COUT)
1. The value of the output capacitor together with the inductor defines the dominate pole-pair of the switching
regulator loop. For stable operation, the capacitor must satisfy :
25
COUT 13,300 22.2 )
10 150
t
u
IN Max
OUT
OUT
V
C 13,300 )
V L +
tu
24
LM2576
,
LM2576HV
SNVS107E –JUNE 1999–REVISED JUNE 2020
www.ti.com
Product Folder Links: LM2576 LM2576HV
Submit Documentation Feedback Copyright © 1999–2020, Texas Instruments Incorporated
yields capacitor values between 10 μF and 2200 μF that satisfies the loop requirements for stable operation.
To achieve an acceptable output ripple voltage, (approximately 1% of the output voltage) and transient
response, the output capacitor may need to be several times larger than yields.
However, for acceptable output ripple voltage select:
COUT ≥680 μF
COUT = 680-μF electrolytic capacitor
2. The voltage rating of the capacitor must be at last 1.5 times greater than the output voltage. For a 10-V
regulator, a rating of at least 15 V or more is recommended. Higher voltage electrolytic capacitors generally
have lower ESR numbers, and for this reason, it can be necessary to select a capacitor rate for a higher
voltage than would normally be needed.
8.2.3.2.4 Catch Diode Selection (D1)
1. The catch-diode current rating must be at least 1.2 times greater than the maximum load current. Also, if the
power supply design must withstand a continuous output short, the diode must have a current rating equal to
the maximum current limit of the LM2576. The most stressful condition for this diode is an overload or
shorted output. See Table 3. For this example, a 3.3-A current rating is adequate.
2. The reverse voltage rating of the diode must be at least 1.25 times the maximum input voltage. Use a 30-V
31DQ03 Schottky diode, or any of the suggested fast-recovery diodes in Table 3.
8.2.3.2.5 Input Capacitor (CIN)
An aluminum or tantalum electrolytic bypass capacitor located close to the regulator is needed for stable
operation. A 100-μF aluminum electrolytic capacitor located near the input and ground pins provides sufficient
bypassing.
Table 3. Diode Selection Guide
VRSCHOTTKY FAST RECOVERY
3 A 4 A to 6 A 3 A 4 A to 6 A
20 V 1N5820 1N5823
The following
diodes are all
rated to 100-V
31DF1
HER302
The following
diodes are all
rated to 100-V
50WF10
MUR410
HER602
MBR320P
SR302
30 V
1N5821
50WQ03
1N5824
MBR330
31DQ03
SR303
40 V
1N5822 MBR340
50WQ04
1N5825
MBR340
31DQ04
SR304
50 V MBR350 50WQ0531DQ05
SR305
60 V MBR360 50WR06
50SQ060
DQ06
SR306
25
LM2576
,
LM2576HV
www.ti.com
SNVS107E –JUNE 1999–REVISED JUNE 2020
Product Folder Links: LM2576 LM2576HV
Submit Documentation FeedbackCopyright © 1999–2020, Texas Instruments Incorporated
(1) Schott Corporation, (612) 475-1173, 1000 Parkers Lake Road, Wayzata, MN 55391.
(2) Pulse Engineering, (619) 674-8100, P.O. Box 12235, San Diego, CA 92112.
(3) Renco Electronics Incorporated, (516) 586-5566, 60 Jeffryn Blvd. East, Deer Park, NY 11729.
Table 4. Inductor Selection by Manufacturer's Part Number
INDUCTOR CODE INDUCTOR VALUE SCHOTT(1) PULSE ENG.(2) RENCO(3)
L47 47 μH 671 26980 PE-53112 RL2442
L68 68 μH 671 26990 PE-92114 RL2443
L100 100 μH 671 27000 PE-92108 RL2444
L150 150 μH 671 27010 PE-53113 RL1954
L220 220 μH 671 27020 PE-52626 RL1953
L330 330 μH 671 27030 PE-52627 RL1952
L470 470 μH 671 27040 PE-53114 RL1951
L680 680 μH 671 27050 PE-52629 RL1950
H150 150 μH 671 27060 PE-53115 RL2445
H220 220 μH 671 27070 PE-53116 RL2446
H330 330 μH 671 27080 PE-53117 RL2447
H470 470 μH 671 27090 PE-53118 RL1961
H680 680 μH 671 27100 PE-53119 RL1960
H1000 1000 μH 671 27110 PE-53120 RL1959
H1500 1500 μH 671 27120 PE-53121 RL1958
H2200 2200 μH 671 27130 PE-53122 RL2448
9 Power Supply Recommendations
As in any switching regulator, layout is very important. Rapidly switching currents associated with wiring
inductance generate voltage transients which can cause problems. For minimal inductance and ground loops, the
length of the leads indicated by heavy lines must be kept as short as possible. Single-point grounding (as
indicated) or ground plane construction must be used for best results. When using the adjustable version,
physically locate the programming resistors near the regulator, to keep the sensitive feedback wiring short.
26
LM2576
,
LM2576HV
SNVS107E –JUNE 1999–REVISED JUNE 2020
www.ti.com
Product Folder Links: LM2576 LM2576HV
Submit Documentation Feedback Copyright © 1999–2020, Texas Instruments Incorporated
10 Layout
10.1 Layout Guidelines
Board layout is critical for the proper operation of switching power supplies. First, the ground plane area must be
sufficient for thermal dissipation purposes. Second, appropriate guidelines must be followed to reduce the effects
of switching noise. Switch mode converters are very fast switching devices. In such cases, the rapid increase of
input current combined with the parasitic trace inductance generates unwanted L di/dt noise spikes. The
magnitude of this noise tends to increase as the output current increases. This noise can turn into
electromagnetic interference (EMI) and can also cause problems in device performance. Therefore, take care in
layout to minimize the effect of this switching noise. The most important layout rule is to keep the AC current
loops as small as possible. Figure 33 shows the current flow in a buck converter. The top schematic shows a
dotted line which represents the current flow during the top-switch ON-state. The middle schematic shows the
current flow during the top-switch OFF-state. The bottom schematic shows the currents referred to as AC
currents. These AC currents are the most critical because they are changing in a very short time period. The
dotted lines of the bottom schematic are the traces to keep as short and wide as possible. This also yields a
small loop area reducing the loop inductance. To avoid functional problems due to layout, review the PCB layout
example. Best results are achieved if the placement of the LM2576 device, the bypass capacitor, the Schottky
diode, RFBB, RFBT, and the inductor are placed as shown in Figure 34. TI also recommends using 2-oz copper
boards or heavier to help thermal dissipation and to reduce the parasitic inductances of board traces. See the
AN-1229 SIMPLE SWITCHER® PCB Layout Guidelines Application Report for more information.
Figure 33. Current Flow in Buck Application
27
LM2576
,
LM2576HV
www.ti.com
SNVS107E –JUNE 1999–REVISED JUNE 2020
Product Folder Links: LM2576 LM2576HV
Submit Documentation FeedbackCopyright © 1999–2020, Texas Instruments Incorporated
10.2 Layout Example
Figure 34. LM2576xx Layout Example
10.3 Grounding
To maintain output voltage stability, the power ground connections must be low-impedance (see Figure 26 and
Figure 32). For the 5-lead TO-220 and DDPAK/TO-263 style package, both the tab and pin 3 are ground and
either connection can be used, as they are both part of the same copper lead frame.
10.4 Heat Sink and Thermal Considerations
In many cases, only a small heat sink is required to keep the LM2576 junction temperature within the allowed
operating range. For each application, to determine whether or not a heat sink is required, the following must be
identified:
1. Maximum ambient temperature (in the application)
2. Maximum regulator power dissipation (in application)
3. Maximum allowed junction temperature (125°C for the LM2576). For a safe, conservative design, a
temperature approximately 15°C cooler than the maximum temperatures must be selected.
4. LM2576 package thermal resistances θJA and θJC.
Total power dissipated by the LM2576 can be estimated in Equation 12:
PD= (VIN)(IQ) + (VO/VIN)(ILOAD)(VSAT)
where
• IQ(quiescent current) and VSAT can be found in the Typical Characteristics
• VIN is the applied minimum input voltage
• VOis the regulated output voltage
28
LM2576
,
LM2576HV
SNVS107E –JUNE 1999–REVISED JUNE 2020
www.ti.com
Product Folder Links: LM2576 LM2576HV
Submit Documentation Feedback Copyright © 1999–2020, Texas Instruments Incorporated
Heat Sink and Thermal Considerations (continued)
• ILOAD is the load current (12)
The dynamic losses during turnon and turnoff are negligible if a Schottky type catch diode is used.
When no heat sink is used, the junction temperature rise can be determined by Equation 13:
ΔTJ= (PD)(θJA) (13)
To arrive at the actual operating junction temperature, add the junction temperature rise to the maximum ambient
temperature.
TJ=ΔTJ+ TA(14)
If the actual operating junction temperature is greater than the selected safe operating junction temperature
determined in step 3, then a heat sink is required.
When using a heat sink, the junction temperature rise can be determined by Equation 15:
ΔTJ= (PD)(θJC +θinterface +θHeat sink) (15)
The operating junction temperature is:
TJ= TA+ΔTJ(16)
As in Equation 16, if the actual operating junction temperature is greater than the selected safe operating
junction temperature, then a larger heat sink is required (one that has a lower thermal resistance).
29
LM2576
,
LM2576HV
www.ti.com
SNVS107E –JUNE 1999–REVISED JUNE 2020
Product Folder Links: LM2576 LM2576HV
Submit Documentation FeedbackCopyright © 1999–2020, Texas Instruments Incorporated
11 Device and Documentation Support
11.1 Device Support
11.1.1 Device Nomenclature
11.1.1.1 Definition of Terms
BUCK REGULATOR A switching regulator topology in which a higher voltage is converted to a lower voltage.
Also known as a step-down switching regulator.
BUCK-BOOST REGULATOR A switching regulator topology in which a positive voltage is converted to a
negative voltage without a transformer.
DUTY CYCLE (D) Ratio of the output switch's on-time to the oscillator period.
(17)
CATCH DIODE OR CURRENT STEERING DIODE The diode which provides a return path for the load current
when the LM2576 switch is OFF.
EFFICIENCY (η)The proportion of input power actually delivered to the load.
(18)
CAPACITOR EQUIVALENT SERIES RESISTANCE (ESR) The purely resistive component of a real capacitor's
impedance (see Figure 35). It causes power loss resulting in capacitor heating, which directly
affects the capacitor's operating lifetime. When used as a switching regulator output filter, higher
ESR values result in higher output ripple voltages.
Figure 35. Simple Model of a Real Capacitor
Most standard aluminum electrolytic capacitors in the 100 μF–1000 μF range have 0.5Ωto
0.1ΩESR. Higher-grade capacitors (low-ESR, high-frequency, or low-inductance) in the 100
μF to 1000 μF range generally have ESR of less than 0.15Ω.
EQUIVALENT SERIES INDUCTANCE (ESL) The pure inductance component of a capacitor (see Figure 35).
The amount of inductance is determined to a large extent on the capacitor's construction. In a buck
regulator, this unwanted inductance causes voltage spikes to appear on the output.
OUTPUT RIPPLE VOLTAGE The AC component of the switching regulator's output voltage. It is usually
dominated by the output capacitor's ESR multiplied by the inductor's ripple current (ΔIIND). The
peak-to-peak value of this sawtooth ripple current can be determined by reading Inductor Ripple
Current.
CAPACITOR RIPPLE CURRENT RMS value of the maximum allowable alternating current at which a capacitor
can be operated continuously at a specified temperature.
STANDBY QUIESCENT CURRENT (ISTBY)Supply current required by the LM2576 when in the standby mode
(ON /OFF pin is driven to TTL-high voltage, thus turning the output switch OFF).
INDUCTOR RIPPLE CURRENT (ΔIIND)The peak-to-peak value of the inductor current waveform, typically a
sawtooth waveform when the regulator is operating in the continuous mode (vs. discontinuous
mode).
CONTINUOUS/DISCONTINUOUS MODE OPERATION Relates to the inductor current. In the continuous mode,
the inductor current is always flowing and never drops to zero, vs. the discontinuous mode, where
the inductor current drops to zero for a period of time in the normal switching cycle.
INDUCTOR SATURATION The condition which exists when an inductor cannot hold any more magnetic flux.
30
LM2576
,
LM2576HV
SNVS107E –JUNE 1999–REVISED JUNE 2020
www.ti.com
Product Folder Links: LM2576 LM2576HV
Submit Documentation Feedback Copyright © 1999–2020, Texas Instruments Incorporated
Device Support (continued)
When an inductor saturates, the inductor appears less inductive and the resistive component
dominates. Inductor current is then limited only by the DC resistance of the wire and the available
source current.
OPERATING VOLT MICROSECOND CONSTANT (E•Top)The product (in VoIt•μs) of the voltage applied to the
inductor and the time the voltage is applied. This E•Top constant is a measure of the energy
handling capability of an inductor and is dependent upon the type of core, the core area, the
number of turns, and the duty cycle.
11.1.2 Development Support
11.1.2.1 Custom Design with WEBENCH Tools
Create a Custom Design with WEBENCH Tools
11.2 Documentation Support
11.2.1 Related Documentation
For related documentation, see the following:
Texas Instruments, AN-1229 SIMPLE SWITCHER® PCB Layout Guidelines
11.3 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 5. Related Links
PARTS PRODUCT FOLDER SAMPLE & BUY TECHNICAL
DOCUMENTS TOOLS &
SOFTWARE SUPPORT &
COMMUNITY
LM2576 Click here Click here Click here Click here Click here
LM2576HV Click here Click here Click here Click here Click here
11.4 Support Resources
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do
not necessarily reflect TI's views; see TI's Terms of Use.
11.5 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
11.6 Trademarks
E2E is a trademark of Texas Instruments.
SIMPLE SWITCHER, WEBENCH are registered trademarks of Texas Instruments.
All other trademarks are the property of their respective owners.
11.7 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
31
LM2576
,
LM2576HV
www.ti.com
SNVS107E –JUNE 1999–REVISED JUNE 2020
Product Folder Links: LM2576 LM2576HV
Submit Documentation FeedbackCopyright © 1999–2020, Texas Instruments Incorporated
11.8 Glossary
SLYZ022 —TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
PACKAGE OPTION ADDENDUM
www.ti.com 9-Jun-2020
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM2576HVS-12 NRND DDPAK/
TO-263 KTT 5 45 TBD Call TI Call TI -40 to 125 LM2576
HVS-12 P+
LM2576HVS-12/NOPB ACTIVE DDPAK/
TO-263 KTT 5 45 Green (RoHS
& no Sb/Br) SN Level-3-245C-168 HR -40 to 125 LM2576
HVS-12 P+
LM2576HVS-3.3/NOPB ACTIVE DDPAK/
TO-263 KTT 5 45 Green (RoHS
& no Sb/Br) SN Level-3-245C-168 HR -40 to 125 LM2576
HVS-3.3 P+
LM2576HVS-5.0 NRND DDPAK/
TO-263 KTT 5 45 TBD Call TI Call TI -40 to 125 LM2576
HVS-5.0 P+
LM2576HVS-5.0/NOPB ACTIVE DDPAK/
TO-263 KTT 5 45 Green (RoHS
& no Sb/Br) SN Level-3-245C-168 HR -40 to 125 LM2576
HVS-5.0 P+
LM2576HVS-ADJ NRND DDPAK/
TO-263 KTT 5 45 TBD Call TI Call TI -40 to 125 LM2576
HVS-ADJ P+
LM2576HVS-ADJ/NOPB ACTIVE DDPAK/
TO-263 KTT 5 45 Green (RoHS
& no Sb/Br) SN Level-3-245C-168 HR -40 to 125 LM2576
HVS-ADJ P+
LM2576HVSX-12 NRND DDPAK/
TO-263 KTT 5 500 TBD Call TI Call TI -40 to 125 LM2576
HVS-12 P+
LM2576HVSX-12/NOPB ACTIVE DDPAK/
TO-263 KTT 5 500 Green (RoHS
& no Sb/Br) SN Level-3-245C-168 HR -40 to 125 LM2576
HVS-12 P+
LM2576HVSX-3.3/NOPB ACTIVE DDPAK/
TO-263 KTT 5 500 Green (RoHS
& no Sb/Br) SN Level-3-245C-168 HR -40 to 125 LM2576
HVS-3.3 P+
LM2576HVSX-5.0 NRND DDPAK/
TO-263 KTT 5 500 TBD Call TI Call TI -40 to 125 LM2576
HVS-5.0 P+
LM2576HVSX-5.0/NOPB ACTIVE DDPAK/
TO-263 KTT 5 500 Green (RoHS
& no Sb/Br) SN Level-3-245C-168 HR -40 to 125 LM2576
HVS-5.0 P+
LM2576HVSX-ADJ NRND DDPAK/
TO-263 KTT 5 500 TBD Call TI Call TI -40 to 125 LM2576
HVS-ADJ P+
LM2576HVSX-ADJ/NOPB ACTIVE DDPAK/
TO-263 KTT 5 500 Green (RoHS
& no Sb/Br) SN Level-3-245C-168 HR -40 to 125 LM2576
HVS-ADJ P+
LM2576HVT-12 NRND TO-220 KC 5 45 TBD Call TI Call TI -40 to 125 LM2576HVT
-12 P+
LM2576HVT-12/LF03 ACTIVE TO-220 NDH 5 45 Green (RoHS
& no Sb/Br) SN Level-1-NA-UNLIM LM2576HVT
-12 P+
LM2576HVT-12/NOPB ACTIVE TO-220 KC 5 45 Green (RoHS
& no Sb/Br) SN Level-1-NA-UNLIM -40 to 125 LM2576HVT
-12 P+
PACKAGE OPTION ADDENDUM
www.ti.com 9-Jun-2020
Addendum-Page 2
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM2576HVT-15/LB03 NRND TO-220 NDH 5 45 TBD Call TI Call TI LM2576HVT
-15 P+
LM2576HVT-15/LF03 ACTIVE TO-220 NDH 5 45 Green (RoHS
& no Sb/Br) SN Level-1-NA-UNLIM LM2576HVT
-15 P+
LM2576HVT-15/NOPB ACTIVE TO-220 KC 5 45 Green (RoHS
& no Sb/Br) SN Level-1-NA-UNLIM -40 to 125 LM2576HVT
-15 P+
LM2576HVT-5.0 NRND TO-220 KC 5 45 TBD Call TI Call TI -40 to 125 LM2576HVT
-5.0 P+
LM2576HVT-5.0/LB03 NRND TO-220 NDH 5 45 TBD Call TI Call TI LM2576HVT
-5.0 P+
LM2576HVT-5.0/LF02 ACTIVE TO-220 NEB 5 45 Green (RoHS
& no Sb/Br) SN Level-1-NA-UNLIM LM2576HVT
-5.0 P+
LM2576HVT-5.0/LF03 ACTIVE TO-220 NDH 5 45 Green (RoHS
& no Sb/Br) SN Level-1-NA-UNLIM LM2576HVT
-5.0 P+
LM2576HVT-5.0/NOPB ACTIVE TO-220 KC 5 45 Green (RoHS
& no Sb/Br) SN Level-1-NA-UNLIM -40 to 125 LM2576HVT
-5.0 P+
LM2576HVT-ADJ NRND TO-220 KC 5 45 TBD Call TI Call TI -40 to 125 LM2576HVT
-ADJ P+
LM2576HVT-ADJ/LB03 NRND TO-220 NDH 5 45 TBD Call TI Call TI LM2576HVT
-ADJ P+
LM2576HVT-ADJ/LF03 ACTIVE TO-220 NDH 5 45 Green (RoHS
& no Sb/Br) SN Level-1-NA-UNLIM LM2576HVT
-ADJ P+
LM2576HVT-ADJ/NOPB ACTIVE TO-220 KC 5 45 Green (RoHS
& no Sb/Br) SN Level-1-NA-UNLIM -40 to 125 LM2576HVT
-ADJ P+
LM2576S-12 NRND DDPAK/
TO-263 KTT 5 45 TBD Call TI Call TI -40 to 125 LM2576S
-12 P+
LM2576S-12/NOPB ACTIVE DDPAK/
TO-263 KTT 5 45 Green (RoHS
& no Sb/Br) SN Level-3-245C-168 HR -40 to 125 LM2576S
-12 P+
LM2576S-3.3/NOPB ACTIVE DDPAK/
TO-263 KTT 5 45 Green (RoHS
& no Sb/Br) SN Level-3-245C-168 HR -40 to 125 LM2576S
-3.3 P+
LM2576S-5.0 NRND DDPAK/
TO-263 KTT 5 45 TBD Call TI Call TI -40 to 125 LM2576S
-5.0 P+
LM2576S-5.0/NOPB ACTIVE DDPAK/
TO-263 KTT 5 45 Green (RoHS
& no Sb/Br) SN Level-3-245C-168 HR -40 to 125 LM2576S
-5.0 P+
LM2576S-ADJ/NOPB ACTIVE DDPAK/
TO-263 KTT 5 45 Green (RoHS
& no Sb/Br) SN Level-3-245C-168 HR -40 to 125 LM2576S
-ADJ P+
PACKAGE OPTION ADDENDUM
www.ti.com 9-Jun-2020
Addendum-Page 3
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM2576SX-3.3/NOPB ACTIVE DDPAK/
TO-263 KTT 5 500 Green (RoHS
& no Sb/Br) SN Level-3-245C-168 HR -40 to 125 LM2576S
-3.3 P+
LM2576SX-5.0/NOPB ACTIVE DDPAK/
TO-263 KTT 5 500 Green (RoHS
& no Sb/Br) SN Level-3-245C-168 HR -40 to 125 LM2576S
-5.0 P+
LM2576SX-ADJ/NOPB ACTIVE DDPAK/
TO-263 KTT 5 500 Green (RoHS
& no Sb/Br) SN Level-3-245C-168 HR -40 to 125 LM2576S
-ADJ P+
LM2576T-12 NRND TO-220 KC 5 45 TBD Call TI Call TI -40 to 125 LM2576T
-12 P+
LM2576T-12/LB03 NRND TO-220 NDH 5 45 TBD Call TI Call TI LM2576T
-12 P+
LM2576T-12/LF03 ACTIVE TO-220 NDH 5 45 Green (RoHS
& no Sb/Br) SN Level-1-NA-UNLIM LM2576T
-12 P+
LM2576T-12/NOPB ACTIVE TO-220 KC 5 45 Green (RoHS
& no Sb/Br) SN Level-1-NA-UNLIM -40 to 125 LM2576T
-12 P+
LM2576T-15/LF03 ACTIVE TO-220 NDH 5 45 Green (RoHS
& no Sb/Br) SN Level-1-NA-UNLIM LM2576T
-15 P+
LM2576T-15/NOPB ACTIVE TO-220 KC 5 45 Green (RoHS
& no Sb/Br) SN Level-1-NA-UNLIM -40 to 125 LM2576T
-15 P+
LM2576T-3.3/LF03 ACTIVE TO-220 NDH 5 45 Green (RoHS
& no Sb/Br) SN Level-1-NA-UNLIM LM2576T
-3.3 P+
LM2576T-3.3/NOPB ACTIVE TO-220 KC 5 45 Green (RoHS
& no Sb/Br) SN Level-1-NA-UNLIM -40 to 125 LM2576T
-3.3 P+
LM2576T-5.0 NRND TO-220 KC 5 45 TBD Call TI Call TI -40 to 125 LM2576T
-5.0 P+
LM2576T-5.0/LB03 NRND TO-220 NDH 5 45 TBD Call TI Call TI LM2576T
-5.0 P+
LM2576T-5.0/LF02 ACTIVE TO-220 NEB 5 45 Green (RoHS
& no Sb/Br) SN Level-1-NA-UNLIM LM2576T
-5.0 P+
LM2576T-5.0/LF03 ACTIVE TO-220 NDH 5 45 Green (RoHS
& no Sb/Br) SN Level-1-NA-UNLIM LM2576T
-5.0 P+
LM2576T-5.0/NOPB ACTIVE TO-220 KC 5 45 Green (RoHS
& no Sb/Br) SN Level-1-NA-UNLIM -40 to 125 LM2576T
-5.0 P+
LM2576T-ADJ NRND TO-220 KC 5 45 TBD Call TI Call TI -40 to 125 LM2576T
-ADJ P+
LM2576T-ADJ/LB03 NRND TO-220 NDH 5 45 TBD Call TI Call TI LM2576T
-ADJ P+
PACKAGE OPTION ADDENDUM
www.ti.com 9-Jun-2020
Addendum-Page 4
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM2576T-ADJ/LF02 ACTIVE TO-220 NEB 5 45 Green (RoHS
& no Sb/Br) SN Level-1-NA-UNLIM LM2576T
-ADJ P+
LM2576T-ADJ/LF03 ACTIVE TO-220 NDH 5 45 Green (RoHS
& no Sb/Br) SN Level-1-NA-UNLIM LM2576T
-ADJ P+
LM2576T-ADJ/NOPB ACTIVE TO-220 KC 5 45 Green (RoHS
& no Sb/Br) SN Level-1-NA-UNLIM -40 to 125 LM2576T
-ADJ P+
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
PACKAGE OPTION ADDENDUM
www.ti.com 9-Jun-2020
Addendum-Page 5
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LM2576HVSX-12 DDPAK/
TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2
LM2576HVSX-12/NOPB DDPAK/
TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2
LM2576HVSX-3.3/NOPB DDPAK/
TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2
LM2576HVSX-5.0 DDPAK/
TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2
LM2576HVSX-5.0/NOPB DDPAK/
TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2
LM2576HVSX-ADJ DDPAK/
TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2
LM2576HVSX-ADJ/NOPB DDPAK/
TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2
LM2576SX-3.3/NOPB DDPAK/
TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2
LM2576SX-5.0/NOPB DDPAK/
TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2
LM2576SX-ADJ/NOPB DDPAK/
TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2
PACKAGE MATERIALS INFORMATION
www.ti.com 30-Mar-2020
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM2576HVSX-12 DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0
LM2576HVSX-12/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0
LM2576HVSX-3.3/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0
LM2576HVSX-5.0 DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0
LM2576HVSX-5.0/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0
LM2576HVSX-ADJ DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0
LM2576HVSX-ADJ/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0
LM2576SX-3.3/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0
LM2576SX-5.0/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0
LM2576SX-ADJ/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0
PACKAGE MATERIALS INFORMATION
www.ti.com 30-Mar-2020
Pack Materials-Page 2
www.ti.com
PACKAGE OUTLINE
C
B
9.25
7.67
6.86
5.69
3.05
2.54
14.73
12.29
5X 1.02
0.64
4X 1.7
8.89
6.86
12.88
10.08
(6.275)
4.83
4.06 1.40
1.14
3.05
2.03
0.61
0.30
-3.963.71
6.8
2X (R1)
OPTIONAL
16.51
MAX
A
10.67
9.65
(4.25)
4215009/A 01/2017
TO-220 - 16.51 mm max heightKC0005A
TO-220
NOTES:
1. All controlling linear dimensions are in inches. Dimensions in brackets are in millimeters. Any dimension in brackets or parenthesis are for
reference only. Dimensioning and tolerancing per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. Shape may vary per different assembly sites.
0.25 C A B
PIN 1 ID
(OPTIONAL)
15
OPTIONAL
CHAMFER
SCALE 0.850
NOTE 3
15
AAAA
www.ti.com
EXAMPLE BOARD LAYOUT
0.07 MAX
ALL AROUND
0.07 MAX
ALL AROUND (1.45)
(2)
(R0.05) TYP
4X (1.45)
4X (2)
5X ( 1.2) (1.7) TYP
(6.8)
FULL R
TYP
TO-220 - 16.51 mm max heightKC0005A
TO-220
4215009/A 01/2017
LAND PATTERN
NON-SOLDER MASK DEFINED
SCALE:12X
PKG
PKG
METAL
TYP
SOLDER MASK
OPENING, TYP
15
MECHANICAL DATA
NDH0005D
www.ti.com
MECHANICAL DATA
KTT0005B
www.ti.com
BOTTOM SIDE OF PACKAGE
TS5B (Rev D)
MECHANICAL DATA
NEB0005B
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2020, Texas Instruments Incorporated
