MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Serial I/O1 .................... 8-bit 1 (UART or Clock-synchronized) Serial I/O2 ...................................8-bit 1 (Clock-synchronized) PWM output .................................................................... 8-bit 1 A-D converter ............................................... 10-bit 8 channels D-A converter ................................................. 8-bit 2 channels LCD drive control circuit Bias ................................................................................... 1/2, 1/3 Duty ........................................................................... 1/2, 1/3, 1/4 Common output .......................................................................... 4 Segment output ........................................................................ 40 2 Clock generating circuits (connect to external ceramic resonator or quartz-crystal oscillator) Watchdog timer ............................................................ 14-bit 1 Power source voltage ................................................ 2.2 to 5.5 V Power dissipation In high-speed mode .......................................................... 40 mW (at 8 MHz oscillation frequency, at 5 V power source voltage) In low-speed mode ............................................................ 60 W (at 32 kHz oscillation frequency, at 3 V power source voltage) Operating temperature range ................................... - 20 to 85C DESCRIPTION The 3827 group is the 8-bit microcomputer based on the 740 family core technology. The 3827 group has the LCD drive control circuit, the A-D/D-A converter, the UART, and the PWM as additional functions. The various microcomputers in the 3827 group include variations of internal memory size and packaging. For details, refer to the section on part numbering. For details on availability of microcomputers in the 3827 group, refer to the section on group expansion. FEATURES Basic machine-language instructions ...................................... 71 The minimum instruction execution time ........................... 0.5 s (at 8MHz oscillation frequency) Memory size ROM ................................................................. 4 K to 60 K bytes RAM ................................................................. 192 to 2048 bytes Programmable input/output ports ............................................ 55 Output port ................................................................................. 8 Input port .................................................................................... 1 Interrupts ................................................. 17 sources, 16 vectors (includes key input interrupt) Timers ........................................................... 8-bit 3, 16-bit 2 APPLICATIONS Camera, wireless phone, etc. 51 53 52 54 56 55 58 57 59 62 61 60 65 64 63 66 68 67 69 71 70 73 72 75 74 77 76 78 80 81 50 82 49 83 48 84 47 85 46 86 45 87 44 88 43 42 89 M38277M8MXXXFP 90 41 RESET P70/INT0 P71 P72 P73 30 28 29 27 25 26 24 22 23 20 21 18 19 P16 P17 P20 P21 P22 P23 P24 P25 P26 P27 VSS XOUT XIN XCOUT XCIN C1 VL1 P67/AN7 P66/AN6 P65/AN5 P64/AN4 P63/SCLK22 /AN3 P62/SCLK21 /AN2 P61/SOUT2/AN1 P60/SIN2/AN0 P57/DA2 P56/DA1 P55/CNTR1 P54/CNTR0 P53/RTP1 P52/RTP0 P51/PWM1 P50/PWM0 P47/SRDY1 P46/SCLK1 P45/TXD P44/RXD P43//TOUT P42/INT2 P41/INT1 P40/ADT P77 P76 P75 P74 15 31 16 17 32 100 12 33 99 13 14 98 11 34 10 35 97 9 36 96 8 37 95 6 7 38 94 5 39 93 4 40 92 3 91 1 2 SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 SEG1 SEG0 VCC VREF AVSS COM3 COM2 COM1 COM0 VL3 VL2 C2 79 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17 P30/SEG18 P31/SEG19 P32/SEG20 P33/SEG21 P34/SEG22 P35/SEG23 P36/SEG24 P37/SEG25 P00/SEG26 P01/SEG27 P02/SEG28 P03/SEG29 P04/SEG30 P05/SEG31 P06/SEG32 P07/SEG33 P10/SEG34 P11/SEG35 P12/SEG36 P13/SEG37 P14/SEG38 P15/SEG39 PIN CONFIGURATION (TOP VIEW) Package type : 100P6S-A (100-pin plastic-molded QFP) Fig. 1 M38277M8MXXXFP pin configuration MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER 52 51 55 53 56 54 58 57 59 61 62 60 64 63 65 67 68 66 70 69 71 72 73 76 50 77 49 78 48 79 80 47 81 46 45 82 44 83 84 43 42 85 86 40 41 87 88 39 M38277M8MXXXGP 38 89 90 37 36 M38277M8MXXXHP 91 92 35 34 93 33 94 32 31 95 96 30 29 97 28 98 99 27 26 24 25 23 21 20 22 19 18 16 17 15 14 13 12 9 8 10 11 7 6 5 4 3 P14 /SEG38 P15 /SEG39 P16 P17 P20 P21 P22 P23 P24 P25 P26 P27 VSS XOUT XIN XCOUT XCIN RESET P70 /INT0 P71 P72 P73 P74 P75 P76 P67/AN7 P66/AN6 P65 /AN5 P64/AN4 P63/SCLK22 /AN3 P62/SCLK21 /AN2 P61 /SOUT2 /AN1 P60/SIN2 /AN0 P57/DA2 P56 /DA1 P55/CNTR 1 P54/CNTR0 P53/RTP 1 P52 /RTP0 P51/PWM1 P50 /PWM0 P47 /SRDY1 P46/SCLK1 P45/ TXD P44/R XD P43 //TOUT P42/INT 2 P41/INT1 P40/ADT P77 2 100 1 SEG12 SEG11 SEG10 SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 SEG1 SEG0 VCC VREF AVSS COM3 COM2 COM1 COM0 VL3 VL2 C2 C1 VL1 74 75 SEG13 SEG14 SEG15 SEG16 SEG17 P30 /SEG18 P31/SEG19 P32/SEG20 P33/SEG21 P34/SEG22 P35 /SEG23 P36/SEG24 P37/SEG25 P00 /SEG26 P01/SEG27 P02/SEG28 P03 /SEG29 P04/SEG30 P05/SEG31 P06/SEG32 P07/SEG33 P10 /SEG34 P11/SEG35 P12/SEG36 P13 /SEG37 PIN CONFIGURATION (TOP VIEW) Package type : GP........ 100P6Q-A (100-pin plastic-molded LQFP) Package type : HP ........ 100PFB-A (100-pin plastic-molded TQFP) Fig. 2 M38277M8MXXXGP/M38277M8MXXXHP pin configuration 2 Sub-clock output Sub-clock input XCIN XCOUT X COUT X CIN I/O port P7 P7(8) Watchdog timer Sub-clock output X COUT INT0 X CIN Sub-clock input SI/O2(8) I/O port P6 Reset P6(8) Main clock output X OUT Clock generating circuit X IN Main clock input VREF AVSS A-D converter (10) PCH C P U DA2 DA1 I/O port P5 P5(8) ADT CNTR0,CNTR1 PS PCL S Y X A PWM(8) I/O port P4 P4(8) SI/O1 (8) Timer 1(8) P3(8) Output port P3 TOUT Timer 3(8) Timer 2(8) Timer Y(16) Timer X(16) ROM VSS VCC RESET Data bus (0V) (5V) Reset input INT1,INT2 FUNCTIONAL BLOCK DIAGRAM I/O port P2 P2(8) D-A2 LCD display RAM (20 bytes) RAM P1(8) I/O port P1 D-A1 LCD drive control circuit I/O port P0 P0(8) SEG0 SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17 COM0 COM1 COM2 COM3 VL1 C1 C2 VL2 VL3 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Fig. 3 Functional block diagram 3 Key input/key-on wake-up interrupt Real time port function MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PIN DESCRIPTION Table 1 Pin description (1) Pin Name Function Function except a port function VCC, VSS Power source *Apply voltage of 2.2 V to 5.5 V to VCC, and 0 V to VSS . VREF Analog reference voltage *Reference voltage input pin for A-D converter and D-A converter. AVSS Analog power source *GND input pin for A-D converter and D-A converter. *Connect to VSS . RESET XIN Reset input *Reset input pin for active "L". Clock input *Input and output pins for the main clock generating circuit. XOUT Clock output *Connect a ceramic resonator or a quartz-crystal oscillator between the XIN and XOUT pins to set the oscillation frequency. *If an external clock is used, connect the clock source to the XIN pin and leave the XOUT pin open. VL1 -VL3 LCD power source *Input 0 VL1 VL2 VL3 VCC voltage. *Input 0 - VL3 voltage to LCD. C1, C2 Charge-pump capacitor pin *External capacitor pins for a voltage multiplier (3 times) of LCD contorl. COM0 -COM3 Common output *LCD common output pins. *COM2 and COM3 are not used at 1/2 duty ratio. SEG0 -SEG17 Segment output *LCD segment output pins. P00/SEG26 - P07/SEG33 I/O port P0 *8-bit output port. *CMOS compatible input level. *COM3 is not used at 1/3 duty ratio. *LCD segment output pins *CMOS 3-state output structure. *Pull-up control is enabled. *I/O direction register allows each port to be individually programmed as either input or output. P10/SEG34 - P15/SEG39 I/O port P1 *6-bit output port with same function as port P0. *CMOS compatible input level. *CMOS 3-state output structure. *Pull-up control is enabled. *I/O direction register allows each 6-bit pin to be programmed as either input or output. *2-bit I/O port. *CMOS compatible input level. P16 , P17 P20 - P2 7 I/O port P2 *CMOS 3-state output structure. *I/O direction register allows each pin to be individually programmed as either input or output. *Pull-up control is enabled. *8-bit I/O port with same function as port P0. *Key input (key-on wake-up) interrupt input pins *CMOS compatible input level. *CMOS 3-state output structure. *Pull-up control is enabled. P3 0/SEG 18 - P3 7/SEG 25 4 Output port P3 *8-bit output port with same function as port P0. *CMOS 3-state output structure. *Port output control is enabled. *LCD segment output pins MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Table 2 Pin description (2) Pin P40 /ADT Name I/O port P4 P41 /INT1 , P42 /INT2 P43//T OUT P44 /RXD, P45 /TXD, P46 /SCLK1 , P47 /SRDY1 P50 /PWM0, P51 /PWM1 Function Function except a port function *1-bit I/O port with same function as P1 6 and P17 . *CMOS compatible input level. *CMOS 3-state output structure. *A-D trigger input pin *Interrupt input pin *7-bit I/O port with same function as P1 6 and P17 . *CMOS compatible input level. *CMOS 3-state output structure. *Pull-up control is enabled. *Interrupt input pins * clock output pin *Timer 2 output pin *Serial I/O1 I/O pins I/O port P5 *8-bit I/O port with same function as P16 and P17. *PWM function pins *CMOS compatible input level. *CMOS 3-state output structure. *Pull-up control is enabled. P52 /RTP0 , P53 /RTP1 *Real time port function pins P54 /CNTR0 , P55 /CNTR1 *Timer X, Y function pins P56 /DA1, P57 /DA2 *D-A conversion output pins P6 0/AN0 /SIN2, I/O port P6 P6 1/AN1 /SOUT2, P6 2/AN2 /SCLK21, P6 3/AN3 /SCLK22 *8-bit I/O port with same function as P16 and P17. *CMOS compatible input level. *CMOS 3-state output structure. *A-D conversion input pins *Serial I/O2 I/O pins *Pull-up control is enabled. P64 /AN4- P67 /AN7 *A-D conversion input pins P70 /INT0 Input port P7 *1-bit I/O port. *CMOS compatible input level. P71 -P77 I/O port P7 *7-bit I/O port with same function as P1 6 and P17. *Interrupt input pin *CMOS compatible input level. *N-channel open-drain output structure. XCOUT Sub-clock output XCIN Sub-clock input *Sub-clock generating circuit I/O pins. (Connect a resonator. External clock cannot be used.) 5 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PART NUMBERING Product M3827 7 M 8 M XXX HP Package type FP : 100P6S-A package HP : 100PFB-A package GP : 100P6Q-A package FS : 100D0 package ROM number Omitted in some types. Normally, using hyphen When electrical characteristic, or division of quality identification code using alphanumeric character. - : Standard M : Low power source version ROM/PROM size 1 : 4096 bytes 2 : 8192 bytes 3 : 12288 bytes 4 : 16384 bytes 5 : 20480 bytes 6 : 24576 bytes 7 : 28672 bytes 8 : 32768 bytes 9 : 36864 bytes A : 40960 bytes B : 45056 bytes C : 49152 bytes D : 53248 bytes E : 57344 bytes F : 61440 bytes The first 128 bytes and the last 2 bytes of ROM are reserved areas ; they cannot be used. Memory type M : Mask ROM version E : EPROM or One Time PROM version RAM size 0 : 192 bytes 1 : 256 bytes 2 : 384 bytes 3 : 512 bytes 4 : 640 bytes 5 : 768 bytes 6 : 896 bytes 7 : 1024 bytes 8 : 1536 bytes 9 : 2048 bytes Fig. 4 Part numbering 6 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER GROUP EXPANSION Package Mitsubishi plans to expand the 3827 group as follows: 100PFB-A ................................0.4 mm-pitch plastic molded TQFP 100P6Q-A ................................ 0.5 mm-pitch plastic molded LQFP 100P6S-A ................................ 0.65 mm-pitch plastic molded QFP 100D0 ..................... Window type ceramic LCC (EPROM version) Memory Type Support for Mask ROM, One Time PROM, and EPROM versions Memory Size ROM/PROM size ................................................. 4 K to 60 K bytes RAM size ............................................................ 192 to 2048 bytes Memory Expansion Plan ROM size (bytes) Under development M38279EF 60K 56K 52K Planning M38278MCM 48K 44K 40K 36K Under development M38277M8M 32K 28K 24K 20K 16K 12K 8K 4K 192 256 384 512 640 768 1024 896 1152 1280 1408 1536 1664 1792 1920 2048 RAM size (bytes) Note: Products under development or planning: the development schedule and specifications may be revised without notice. Fig. 5 Memory expansion plan Currently supported products are listed below. Table 3 List of supported products Product M38277M8MXXXFP M38277M8MXXXHP M38277M8MXXXGP M38279EF-XXXFP M38279EFFP M38279EF-XXXHP M38279EFHP M38279EF-XXXGP M38279EFGP M38279EFFS As of May 1998 (P) ROM size (bytes) ROM size for User in ( ) RAM size (bytes) 32768 (32638) 1024 61440 (61310) 2048 Package 100P6S-A 100PFB-A 100P6Q-A 100P6S-A 100P6S-A 100PFB-A 100PFB-A 100P6Q-A 100P6Q-A 100D0 Remarks Mask ROM version Mask ROM version Mask ROM version One Time PROM version One Time PROM version (blank) One Time PROM version One Time PROM version (blank) One Time PROM version One Time PROM version (blank) EPROM version 7 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER [CPU Mode Register (CPUM)] 003B16 FUNCTIONAL DESCRIPTION Central Processing Unit (CPU) The CPU mode register contains the stack page selection bit and the internal system clock selection bit. The CPU mode register is allocated at address 003B16 . The 3827 group uses the standard 740 family instruction set. Refer to the table of 740 family addressing modes and machine instructions or the 740 Family Software Manual for details on the instruction set. Machine-resident 740 family instructions are as follows: The FST and SLW instruction cannot be used. The STP, WIT, MUL, and DIV instruction can be used. b7 b0 CPU mode register (CPUM (CM) : address 003B 16) Processor mode bits b1 b0 0 0 : Single-chip mode 0 1 : 1 0 : Not available 1 1 : Stack page selection bit 0 : 0 page 1 : 1 page Not used (returns "1" when read) (Do not write "0" to this bit.) Port XC switch bit 0 : Stop oscillating 1 : XCIN , XCOUT Main clock ( X IN -XOUT ) stop bit 0 : Oscillating 1 : Stopped Main clock division ratio selection bit 0 : XIN /2 (high-speed mode) 1 : XIN /8 (middle-speed mode) Internal system clock selection bit 0 : XIN -XOUT selected (middle-/high-speed mode) 1 : XCIN -XCOUT selected (low-speed mode) Fig. 6 Structure of CPU mode register 8 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER MEMORY Special Function Register (SFR) Area The Special Function Register area in the zero page contains control registers such as I/O ports and timers. Zero Page Access to this area with only 2 bytes is possible in the zero page addressing mode. Special Page RAM RAM is used for data storage and for stack area of subroutine calls and interrupts. Access to this area with only 2 bytes is possible in the special page addressing mode. ROM The first 128 bytes and the last 2 bytes of ROM are reserved for device testing and the rest is user area for storing programs. Interrupt Vector Area The interrupt vector area contains reset and interrupt vectors. RAM area 000016 RAM size (bytes) Address XXXX16 192 00FF 16 004016 256 013F 16 005416 384 01BF16 512 023F 16 640 02BF16 768 033F 16 896 03BF16 1024 043F 16 1536 063F 16 2048 083F 16 SFR area LCD display RAM area Zero page 010016 RAM XXXX16 Reserved area 084016 Not used ROM area ROM size (bytes) Address YYYY16 Address ZZZZ 16 4096 F000 16 F080 16 8192 E00016 E080 16 12288 D00016 D08016 16384 C00016 C08016 20480 B00016 B080 16 24576 A00016 A080 16 28672 900016 908016 32768 800016 808016 36864 700016 708016 40960 600016 608016 45056 500016 508016 49152 400016 408016 53248 300016 308016 57344 200016 208016 61440 100016 108016 YYYY16 Reserved ROM area (128 bytes) ZZZZ 16 ROM FF0016 FFDC16 Interrupt vector area Special page FFFE16 Reserved ROM area FFFF 16 Fig. 7 Memory map diagram 9 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER 000016 Port P0 (P0) 000116 Port P0 direction register (P0D) 002016 Timer X (low) (TXL) 002116 Timer X (high) (TXH) 000216 Port P1 (P1) 000316 Port P1 output control register (P1D) 002216 Timer Y (low) (TYL) 002316 Timer Y (high) (TYH) 000416 Port P2 (P2) 000516 Port P2 direction register (P2D) 002416 Timer 1 (T1) 000616 Port P3 (P3) 000716 Port P3 output control register (P3C) 000816 Port P4 (P4) 000916 Port P4 direction register (P4D) 000A16 Port P5 (P5) 000B16 Port P5 direction register (P5D) 002716 Timer X mode register (TXM) 002816 Timer Y mode register (TYM) 002916 Timer 123 mode register (T123M) 002A16 TOUT / output control register (CKCON) 002B16 PWM control register (PWMCON) 000C16 Port P6 (P6) 000D16 Port P6 direction register (P6D) 002C16 PWM prescaler (PREPWM) 000E16 Port P7 (P7) 000F16 Port P7 direction register (P7D) 002E16 001016 003016 001116 003116 A-D control register (ADCON) 001216 003216 A-D control register (low-order) (ADL) 003316 A-D control register (high-order) (ADH) 001316 002D16 PWM register (PWM) 002F 16 001516 Key input control register (KIC) 003416 D-A1 conversion register (DA1) 003516 D-A2 conversion register (DA2) 001616 PULL register A (PULLA) 001716 PULL register B (PULLB) 003616 D-A control register (DACON) 003716 Watchdog timer control register (WDTCON) 001816 Transmit/Receive buffer register(TB/RB) 001916 Serial I/O1 status register (SIO1STS) 003816 Segment output enable register (SEG) 001416 001A16 Serial I/O1 control register (SIO1CON) 001B16 UART control register (UARTCON) 003916 LCD mode register (LM) 003A16 Interrupt edge selection register (INTEDGE) 003B16 CPU mode register (CPUM) 001C16 Baud rate generator (BRG) 001D16 Serial I/O2 control register (SIO2CON) 003C16 Interrupt request register 1(IREQ1) 003D16 Interrupt request register 2(IREQ2) 001E16 Reserved area 001F16 Serial I/O2 register (SIO2) 003E16 Interrupt control register 1(ICON1) 003F 16 Interrupt control register 2(ICON2) Fig. 8 Memory map of special function register (SFR) 10 002516 Timer 2 (T2) 002616 Timer 3 (T3) MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER I/O PORTS Direction Registers The I/O ports have direction registers which determine the input/ output direction of each individual pin. (P00-P07 and P10 -P15 use bit 0 of port P0, P1 direction registers respectively.) When "1" is written to that bit, that pin becomes an output pin. When "0" is written to the bit corresponding to a pin, that pin becomes an input pin. If data is read from a pin set to output, the value of the port output latch is read, not the value of the pin itself. Pins set to input are floating and the value of that pin can be read. If a pin set to input is written to, only the port output latch is written to and the pin remains floating. Port P3 Output Control Register Bit 0 of the port P3 output control register (address 000716) enables control of the output of ports P3 0 to P37. When the bit is set to "1", the port output function is valid. When resetting, bit 0 of the port P3 output control register is set to "0" (the port output function is invalid.) and ports P30 to P37 are pulled up. Pull-up Control By setting the PULL register A (address 001616 ) or the PULL register B (address 001716 ), ports P0 to P6 can control pull-up with a program. However, the contents of PULL register A and PULL register B do not affect ports programmed as the output ports. The PULL register A setting is invalid for pins set to segment output on the segment output enable register. b7 b0 PULL register A (PULLA : address 0016 16) P00 , P01 pull-up P02 ,P03 pull-up P04 -P07 pull-up P10 -P13 pull-up P14 ,P15 pull-up P16 ,P17 pull-up P20 -P23 pull-up P24 -P27 pull-up b7 b0 PULL register B (PULLB : address 0017 16) P41 -P43 pull-up P44 -P47 pull-up P50 -P53 pull-up P54 -P57 pull-up P60 -P63 pull-up P64 -P67 pull-up Not used (return "0" when read) 0 : No pull-up 1 : Pull-up Note : The contents of PULL register A and PULL register B do not affect ports programmed as the output port. Fig. 9 Structure of PULL register A and PULL register B 11 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Table 4 List of I/O port function (1) Pin Name P00 /SEG26 - P07 /SEG33 Por t P0 Input/output, byte unit CMOS compatible input level CMOS 3-state output LCD segment output PULL register A Segment output enable register P10 /SEG34 - P15 /SEG39 Por t P1 Input/output, 6-bit unit CMOS compatible input level CMOS 3-state output LCD segment output PULL register A Segment output enable register (1) (2) Input/output, individual bits CMOS compatible input level CMOS 3-state output PULL register A (4) Input/output, individual bits CMOS compatible input level CMOS 3-state output Key input (key-on wake-up) interrupt input PULL register A (4) P16 , P17 P20 -P27 Port P2 Input/Output I/O Format Non-Port Function Related SFRs Diagram No. (1) (2) Interrupt control register2 Key input control register P30 /SEG18 - P37 /SEG25 Por t P3 Output CMOS 3-state output LCD segment output PULL register A Segment output enable register P3 output enable register (3) P40 /ADT Por t P4 Input/output, individual bits CMOS compatible input level N-channel open-drain output A-D trigger input External interrupt input A-D control register Interrupt edge selection register (13) CMOS compatible input level CMOS 3-state output External interrupt input PULL register B Interrupt edge selection register (4) Timer output output PULL register B P41 /INT1 , P42 /INT2 P43//T OUT (12) Timer 123 mode register TOUT/ output control register Serial I/O1 function I/O P44 /RXD, P45 /TXD, P46 /SCLK1 , P47 /SRDY1 P50 /PWM0, P51 /PWM1 Port P5 Input/output, individual bits CMOS compatible input level CMOS 3-state output PWM output PULL register B Serial I/O1 control register Serial I/O1 status register UART control register PULL register B PWM control register (5) (6) (7) (8) (10) Real time port function output PULL register B Timer X mode register (9) P54 /CNTR0 Timer X function I/O PULL register B Timer X mode register (11) P55 /CNTR1 Timer Y function input PULL register B Timer Y mode register (14) P56 /DA1 DA1 output A-D VREF input PULL register B D-A control register A-D control register (15) P57 /DA2 DA2 output PULL register B D-A control register (15) P52 /RTP0 , P53 /RTP1 12 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Table 5 List of I/O port function (2) Pin P60 /SIN2/AN0 Name Por t P6 P61 /SOUT2/ AN 1 Input/Output Input/ output, individnal bits I/O Format CMOS compatible input level CMOS 3-state output Non-Port Function A-D conversion input Serial I/O2 function I/O Related SFRS Diagram No. A-D control register Serial I/O2 control register (17) (18) P62 /SCLK21/ AN 2 (19) P63 /SCLK22 / AN 3 (20) P64 /AN4- P67 /AN7 P70 /INT0 Por t P7 P71 -P77 Input CMOS compatible input level Input/ output, individnal bits CMOS compatible input level N-channel open-drain output COM0-COM3 Common Output LCD common output SEG 0-SEG17 Segment Output LCD segment output A-D conversion input A-D control register (16) External interrupt input Interrupt edge selection register (23) (13) LCD mode register (21) (22) Notes1: How to use double-function ports as function I/O ports, refer to the applicable sections. 2: Make sure that the input level at each pin is either 0 V or VCC during execution of the STP instruction. When an input level is at an intermediate potential, a current will flow VCC to V SS through the input-stage gate. 13 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER (1) Ports P01-P07, P11-P15 Pull-up VL2/VL3/VCC Segment/Port LCD drive timing Segment data Interface logic level shift circuit Port latch Data bus Segment Port direction register VL1/VSS Port Port/Segment Port direction register (2) Ports P00, P10 Pull-up VL2/VL3/VCC Segment/Port LCD drive timing Direction register Segment data Data bus Interface logic level shift circuit Port latch Segment Port/Segment Port direction register VL1/VSS Port (3) Port P3 Pull-up LCD drive timing VL2/VL3/VCC Segment/Port Interface logic level shift circuit Segment Segment data Data bus Port latch Port/Segment Output control (4) Ports P16, P17, P2, P41, P42 Pull-up control VL1/VSS Port (5) Port P44 Serial I/O1 enable bit Reception enable bit Direction register Data bus Port latch Except P16, P17 Fig. 10 Port block diagram (1) 14 Direction register Data bus Key input interrupt input INT1, INT2 interrupt input Pull-up control Port latch Serial I/O1 input MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER (6) Port P45 (7) Port P46 Pull-up control P45/TxD P-channel output disable bit Serial I/O1 enable bit Transmission enable bit Serial I/O1 clock selection bit Serial I/O1 enable bit Serial I/O1 mode selection bit Serial I/O1 enable bit Direction register Direction register Port latch Data bus Pull-up control Data bus Serial I/O1 output Port latch Serial I/O1 clock outupt Serial I/O1 clock input (8) Port P47 (9) Ports P52, P53 Serial I/O1 mode selection bit Serial I/O1 enable bit SRDY1 output enable bit Pull-up control Pull-up control Direction register Direction register Data bus Data bus Port latch Port latch Real time control bit Real time port data Serial I/O1 ready output (11) Port P54 (10) Ports P50,P51 Pull-up control Pull-up control Direction register Direction register Data bus Data bus Port latch Port latch Pulse output mode Timer output PWM function enable bit PWM output CNTR0 interrupt input Fig. 11 Port block diagram (2) 15 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER (13) Ports P40, P71-P77 (12) Port P43 Pull-up control Direction register Direction register Data bus Data bus Port latch TOUT/ output control Timer output TOUT/ selection bit output Port latch A-D trigger input Except P71 to P77 (15) Ports P56, P57 (14) Port P55 Pull-up control Pull-up control Direction register Direction register Data bus Data bus Port latch Port latch CNTR1 interrupt input Except P57 D-A conversion output D-A1, D-A2 output enable bit VREF input switch VREF input selection bit (17) Port P60 (16) Ports P64-P67 Pull-up control Pull-up control Direction register Direction register Data bus Port latch A-D conversion input Analog input pin selection bit Data bus Port latch Serial I/O2 input A-D conversion input Analog input pin selection bit Fig. 12 Port block diagram (3) 16 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER (18) Port P61 (19) Port P62 P61/SOUT2 P-channel output disable bit Serial I/O2 transmit completion signal Synchronous clock selection bit Serial I/O2 port selection bit Pull-up control Serial I/O2 port selection bit Synchronous clock output pin selection bit Direction register Data bus Pull-up control Synchronous clock selection bit Direction register Port latch Data bus Serial I/O2 output A-D conversion input Analog input pin selection bit Port latch Serial I/O2 clock output Serial I/O2 clock input A-D conversion input Analog input pin selection bit (20) Port P63 Pull-up control (21) COM0-COM3 Synchronous clock selection bit Serial I/O2 port selection bit Synchronous clock output pin selection bit VL3 Direction register Data bus VL2 Port latch The gate input signal of each transistor is controlled by the LCD duty ratio and the bias value. VL1 Serial I/O2 clock output VSS A-D conversion input Analog input pin selection bit (23) Port P70 (22) SEG0-SEG17 Direction register VL2/VL3 The voltage applied to the sources of P-channel and N-channel transistors is the controlled voltage by the bias value. Data bus Port latch VL1/VSS INT0 input Fig. 13 Port block diagram (4) 17 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER INTERRUPTS Interrupt Operation Interrupts occur by seventeen sources: seven external, nine internal, and one software. Upon acceptance of an interrupt the following operations are automatically performed: 1. The contents of the program counter and processor status register are automatically pushed onto the stack. 2. The interrupt disable flag is set and the corresponding interrupt request bit is cleared. 3. The interrupt jump destination address is read from the vector table into the program counter. Interrupt Control Each interrupt except the BRK instruction interrupt have both an interrupt request bit and an interrupt enable bit, and is controlled by the interrupt disable flag. An interrupt occurs if the corresponding interrupt request and enable bits are "1" and the interrupt disable flag is "0." Interrupt enable bits can be set or cleared by software. Interrupt request bits can be cleared by software, but cannot be set by software. The BRK instruction interrupt and reset cannot be disabled with any flag or bit. The I flag disables all interrupts except the BRK instruction interrupt and reset. If several interrupts requests occurs at the same time the interrupt with highest priority is accepted first. Notes When the active edge of an external interrupt (INT0-INT2, CNTR0 , CNTR1 ) is set or when switching interrupt sources of ADT/A-D conversion interrupt, the corresponding interrupt request bit may also be set. Therefore, take following sequence: (1) Disable the external interrupt which is selected. (2) Change the active edge in interrupt edge selection register (timer XY mode register when using CNTR0 , CNTR1) (3) Clear the set interrupt request bit to "0." (4) Enable the external interrupt which is selected. Table 6 Interrupt vector addresses and priority Interrupt Source Priority Vector Addresses (Note 1) High Low Interrupt Request Generating Conditions At reset At detection of either rising or falling edge of INT0 input At detection of either rising or falling edge of INT1 input Remarks Reset (Note 2) INT 0 1 2 FFFD 16 FFFB16 FFFC16 FFFA16 INT 1 3 FFF916 FFF816 Serial I/O1 reception 4 FFF716 FFF616 Serial I/O1 transmission 5 FFF516 FFF416 Timer X 6 FFF316 FFF216 Timer Y Timer 2 Timer 3 CNTR 0 7 8 9 10 FFF116 FFEF16 FFED16 FFEB 16 FFF016 FFEE16 FFEC16 FFEA16 CNTR 1 11 FFE916 FFE816 At detection of either rising or falling edge of CNTR1 input Timer 1 INT 2 12 13 FFE716 FFE516 FFE616 At timer 1 underflow FFE416 External interrupt (active edge selectable) Serial I/O2 14 FFE316 FFE216 At detection of either rising or falling edge of INT2 input At completion of serial I/O2 data transmission or reception Key input (Key-on wake-up) 15 FFE116 FFE016 At falling of conjunction of input level for port P2 (at input mode) ADT 16 FFDF 16 FFDE16 At falling of ADT input External interrupt (valid when an "L" level is applied) Valid when ADT interrupt is selected External interrupt (Valid at falling) A-D conversion BRK instruction At completion of serial I/O1 data reception At completion of serial I/O1 transmit shift or when transmission buffer is empty At timer X underflow At timer Y underflow At timer 2 underflow At timer 3 underflow At detection of either rising or falling edge of CNTR0 input At completion of A-D conversion 17 FFDD 16 FFDC16 At BRK instruction execution Notes1: Vector addresses contain interrupt jump destination addresses. 2: Reset function in the same way as an interrupt with the highest priority. 18 Non-maskable External interrupt (active edge selectable) External interrupt (active edge selectable) Valid when serial I/O1 is selected Valid when serial I/O1 is selected External interrupt (active edge selectable) External interrupt (active edge selectable) Valid when serial I/O2 is selected Valid when A-D interrupt is selected Non-maskable software interrupt MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Interrupt request bit Interrupt enable bit Interrupt disable flag (I) Interrupt request BRK instruction Reset Fig. 14 Interrupt control b7 b0 Interrupt edge selection register (INTEDGE : address 003A 16) INT0 interrupt edge selection bit INT1 interrupt edge selection bit INT2 interrupt edge selection bit INT3 interrupt edge selection bit Not used (return "0" when read) b7 b0 0 : Falling edge active 1 : Rising edge active Interrupt request register 1 (IREQ1 : address 003C 16) b7 b0 INT0 interrupt request bit INT1 interrupt request bit Serial I/O1 receive interrupt request bit Serial I/O1 transmit interrupt request bit Timer X interrupt request bit Timer Y interrupt request bit Timer 2 interrupt request bit Timer 3 interrupt request bit Interrupt request register 2 (IREQ2 : address 003D 16) CNTR0 interrupt request bit CNTR1 interrupt request bit Timer 1 interrupt request bit INT2 interrupt request bit Serial I/O2 interrupt request bit Key input interrupt request bit ADT/AD conversion interrupt request bit Not used (returns "0" when read) 0 : No interrupt request issued 1 : Interrupt request issued b7 b0 Interrupt control register 1 (ICON1 : address 003E 16) INT0 interrupt enable bit INT1 interrupt enable bit Serial I/O receive interrupt enable bit Serial I/O transmit interrupt enable bit Timer X interrupt enable bit Timer Y interrupt enable bit Timer 2 interrupt enable bit Timer 3 interrupt enable bit b7 b0 Interrupt control register 2 (ICON2 : address 003F 16 ) CNTR0 interrupt enable bit CNTR1 interrupt enable bit Timer 1 interrupt enable bit INT2 interrupt enable bit Serial I/O2 interrupt enable bit Key input interrupt enable bit ADT/AD conversion interrupt enable bit Not used (returns "0" when read) (Do not write "1" to this bit.) 0 : Interrupts disabled 1 : Interrupts enabled Fig. 15 Structure of interrupt-related registers 19 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Key Input Interrupt (Key-on wake-up) A Key-on wake up interrupt request is generated by applying "L" level to any pin of port P2 that have been set to input mode. In other words, it is generated when AND of input level goes from "1" to "0". An example of using a key input interrupt is shown in Figure 16, where an interrupt request is generated by pressing one of the keys consisted as an active-low key matrix which inputs to ports P20-P23. Port PXx "L" level output Port P27 output Port P26 output Port P25 output Port P24 output Port P23 input Port P22 input Port P21 input Port P20 input PULLA register Key input control register = "1" Bit 2 = "1" Port P27 direction register = "1" Port P27 latch Key input interrupt request Key input control register = "1" Port P26 direction register = "1" Port P26 latch Key input control register = "1" Port P25 direction register = "1" Port P25 latch Key input control register = "1" Port P24 direction register = "1" Port P24 latch Key input control register = "1" Port P23 direction register = "0" Port P23 latch Port P2 input reading circuit Key input control register = "1" Port P22 direction register = "0" Port P22 latch Key input control register = "1" Port P21 direction register = "0" Port P21 latch Key input control register = "1" Port P20 direction register = "0" Port P20 latch P-channel transistor for pull-up CMOS output buffer Fig. 16 Connection example when using key input interrupt and port P2 block diagram 20 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER responding to that timer is set to "1". Read and write operation on 16-bit timer must be performed for both high and low-order bytes. When reading a 16-bit timer, read the high-order byte first. When writing to a 16-bit timer, write the low-order byte first. The 16-bit timer cannot perform the correct operation when reading during the write operation, or when writing during the read operation. TIMERS The 3827 group has five timers: timer X, timer Y, timer 1, timer 2, and timer 3. Timer X and timer Y are 16-bit timers, and timer 1, timer 2, and timer 3 are 8-bit timers. All timers are down count timers. When the timer reaches "0016", an underflow occurs at the next count pulse and the corresponding timer latch is reloaded into the timer and the count is continued. When a timer underflows, the interrupt request bit cor- Real time port control bit "1" Data bus Q D P52 data for real time port Latch "0" P52 latch Real time port control bit "1" Q D P53 data for real time port P52 P52 direction register P53 Real time port control bit "0" Latch "0" P53 direction register P53 latch Timer X mode register write signal "1" f(X IN )/16 (f(XIN )/16 in low-speed mode ) P54/CNTR0 Timer X stop control bit Timer X operating mode bits "00","01","11" CNTR0 active edge switch bit "0" "10" "1" Pulse width measurement mode CNTR0 active edge switch bit "0" "1" P54 direction register Timer X write control bit Timer X (low) latch (8) Timer X (high) latch (8) Timer X (low) (8) Timer X (high) (8) CNTR0 interrupt request Pulse output mode QS Timer Y operating mode bit "00","01","10" T Q Pulse width HL continuously measurement mode P54 latch Period measurement mode Falling edge detection f(XIN )/16 (f(XCIN)16 in = XCIN divided by 2) P55 /CNTR1 Timer Y stop control bit "00","01","11" Timer Y (low) latch (8) Timer Y (high) latch (8) Timer Y (low) (8) Timer Y (high) (8) "10" Timer Y operating mode bit "1" f(XIN )/16 (f(XCIN )/16 in = XCIN divided by 2) Timer 1 count source selection bit "0" Timer 1 latch (8) Timer 2 count source selection bit Timer 2 latch (8) "0" Timer 1 (8) XCIN CNTR1 interrupt request "11" Rising edge detection Pulse output mode CNTR1 active edge switch bit "0" Timer X interrupt request "1" Timer 2 (8) "1" Timer 2 write control bit Timer Y interrupt request Timer 1 interrupt request Timer 2 interrupt request f(XIN)/16 (f(XCIN )16 in =XCIN divided by 2) TOUT output TOUT output active edge control bit TOUT output switch bit control bit "0" QS P43 //TOUT T "1" P43 latch Q P43 direction register f(X IN )/16(f(XCIN )/16 in low-speed mode ) "0" Timer 3 latch (8) Timer 3 (8) "1" Timer 3 count source selection bit Timer 3 interrupt request Fig. 17 Timer block diagram 21 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Timer X Timer X is a 16-bit timer that can be selected in one of four modes and can be controlled the timer X write and the real time port by setting the timer X mode register. (1) Timer Mode The timer counts f(XIN)/16 (or f(X CIN)/16 in low-speed mode). (2) Pulse Output Mode Each time the timer underflows, a signal output from the CNTR0 pin is inverted. Except for this, the operation in pulse output mode is the same as in timer mode. When using a timer in this mode, set the port shared with the CNTR0 pin to input. Note on CNTR 0 interrupt active edge selection CNTR0 interrupt active edge depends on the CNTR0 active edge switch bit. Real time port control While the real time port function is valid, data for the real time port are output from ports P5 2 and P53 each time the timer X underflows. (However, if the real time port control bit is changed from "0" to "1", data are output without the timer X.) When the data for the real time port is changed while the real time port function is valid, the changed data are output at the next underflow of timer X. Before using this function, set the corresponding port direction registers to output mode. (3) Event Counter Mode The timer counts signals input through the CNTR0 pin. Except for this, the operation in event counter mode is the same as in timer mode. When using a timer in this mode, set the port shared with the CNTR 0 pin to input. (4) Pulse Width Measurement Mode The count source is f(XIN)/16 (or f(XCIN)/16 in low-speed mode). If CNTR0 active edge switch bit is "0", the timer counts while the input signal of CNTR0 pin is at "H". If it is "1", the timer counts while the input signal of CNTR0 pin is at "L". When using a timer in this mode, set the port shared with tha CNTR0 pin to input. Timer X write control If the timer X write control bit is "0", when the value is written in the address of timer X, the value is loaded in the timer X and the latch at the same time. If the timer X write control bit is "1", when the value is written in the address of timer X, the value is loaded only in the latch. The value in the latch is loaded in timer X after timer X underflows. If the value is written in latch only, unexpected value may be set in the high-order counter when the writing in high-order latch and the underflow of timer X are performed at the same timing. b7 b0 Timer X mode register (TXM : address 0027 16) Timer X write control bit 0 : Write value in latch and counter 1 : Write value in latch only Real time port control bit 0 : Real time port function invalid 1 : Real time port function valid P52 data for real time port P53 data for real time port Timer X operating mode bits b5 b4 0 0 : Timer mode 0 1 : Pulse output mode 1 0 : Event counter mode 1 1 : Pulse width measurement mode CNTR0 active edge switch bit 0 : Count at rising edge in event counter mode Start from "H" output in pulse output mode Measure "H" pulse width in pulse width measurement mode Falling edge active for CNTR 0 interrupt 1 : Count at falling edge in event counter mode Start from "L" output in pulse output mode Measure "L" pulse width in pulse width measurement mode Rising edge active for CNTR 0 interrupt Timer X stop control bit 0 : Count start 1 : Count stop Fig. 18 Structure of timer X mode register 22 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Timer Y Timer Y is a 16-bit timer that can be selected in one of four modes. (1) Timer Mode The timer counts f(XIN)/16 (or f(X CIN)/16 in low-speed mode). (2) Period Measurement Mode CNTR 1 interrupt request is generated at rising/falling edge of CNTR1 pin input signal. Simultaneously, the value in timer Y latch is reloaded in timer Y and timer Y continues counting down. Except for the above-mentioned, the operation in period measurement mode is the same as in timer mode. The timer value just before the reloading at rising/falling of CNTR1 pin input signal is retained until the timer Y is read once after the reload. The rising/falling timing of CNTR 1 pin input signal is found by CNTR1 interrupt. When using a timer in this mode, set the por t shared with the CNTR 1 pin to input. (3) Event Counter Mode The timer counts signals input through the CNTR1 pin. Except for this, the operation in event counter mode is the same as in timer mode. When using a timer in this mode, set the port shared with the CNTR 1 pin to input. b7 b0 Timer Y mode register (TYM : address 0028 16) Not used (return "0" when read) Timer Y operating mode bits b5 b4 0 0 : Timer mode 0 1 : Period measurement mode 1 0 : Event counter mode 1 1 : Pulse width HL continuously measurement mode CNTR1 active edge switch bit 0 : Count at rising edge in event counter mode Measure the falling edge to falling edge period in period measurement mode Falling edge active for CNTR 1 interrupt 1 : Count at falling edge in event counter mode Measure the rising edge period in period measurement mode Rising edge active for CNTR 1 interrupt Timer Y stop control bit 0 : Count start 1 : Count stop Fig. 19 Structure of timer Y mode register (4) Pulse Width HL Continuously Measurement Mode CNTR1 interrupt request is generated at both rising and falling edges of CNTR1 pin input signal. Except for this, the operation in pulse width HL continuously measurement mode is the same as in period measurement mode. When using a timer in this mode, set the port shared with the CNTR1 pin to input. Note on CNTR1 interrupt active edge selection CNTR 1 interrupt active edge depends on the CNTR1 active edge switch bit. However, in pulse width HL continuously measurement mode, CNTR 1 interrupt request is generated at both rising and falling edges of CNTR1 pin input signal regardless of the setting of CNTR1 active edge switch bit. 23 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Timer 1, Timer 2, Timer 3 Timer 1, timer 2, and timer 3 are 8-bit timers. The count source for each timer can be selected by timer 123 mode register. The timer latch value is not affected by a change of the count source. However, because changing the count source may cause an inadvertent count down of the timer. Therefore, rewrite the value of timer whenever the count source is changed. Timer 2 write control If the timer 2 write control bit is "0", when the value is written in the address of timer 2, the value is loaded in the timer 2 and the latch at the same time. If the timer 2 write control bit is "1", when the value is written in the address of timer 2, the value is loaded only in the latch. The value in the latch is loaded in timer 2 after timer 2 underflows. Timer 2 output control When the timer 2 (TOUT) is output enabled, an inversion signal from the TOUT pin is output each time timer 2 underflows. In this case, set the port shared with the TOUT pin to the output. Notes on timer 1 to timer 3 When the count source of timer 1 to 3 is changed, the timer counting value may be changed large because a thin pulse is generated in count input of timer . If timer 1 output is selected as the count source of timer 2 or timer 3, when timer 1 is written, the counting value of timer 2 or timer 3 may be changed large because a thin pulse is generated in timer 1 output. Therefore, set the value of timer in the order of timer 1, timer 2 and timer 3 after the count source selection of timer 1 to 3. 24 b7 b0 Timer 123 mode register (T123M :address 0029 16) TOUT output active edge switch bit 0 : Start at "H" output 1 : Start at "L" output TOUT / output control bit 0 : T OUT / output disabled 1 : T OUT / output enabled Timer 2 write control bit 0 : Write data in latch and counter 1 : Write data in latch only Timer 2 count source selection bit 0 : Timer 1 output 1 : f(XIN )/16 (or f(XCIN )/16 in low-speed mode) Timer 3 count source selection bit 0 : Timer 1 output 1 : f(XIN )/16 (or f(XCIN )/16 in low-speed mode) Timer 1 count source selection bit 0 : f(XIN )/16 (or f(XCIN )/16 in low-speed mode) 1 : f(XCIN ) Not used (return "0" when read) Note : Internal clock is XCIN /2 in the low-speed mode. Fig. 20 Structure of timer 123 mode register MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER (1) Clock Synchronous Serial I/O Mode SERIAL I/O Serial I/O1 Serial I/O1 can be used as either clock synchronous or asynchronous (UART) serial I/O. A dedicated timer (baud rate generator) is also provided for baud rate generation. Clock synchronous serial I/O1 can be selected by setting the mode selection bit of the serial I/O1 control register to "1". For clock synchronous serial I/O1, the transmitter and the receiver must use the same clock. If an internal clock is used, transfer is started by a write signal to the transmit/receive buffer registers. Data bus Serial I/O1 control register Address 0018 16 Receive buffer register Receive shift register P44/RXD Address 001A16 Receive buffer full flag (RBF) Receive interrupt request (RI) Shift clock Clock control circuit P46/SCLK Serial I/O1 clock selection bit Frequency division ratio 1/(n+1) Baud rate generator 1/4 Address 001C 16 BRG count source selection bit f(XIN ) (f(XCIN ) in low-speed mode) 1/4 P47/SRDY1 F/F Clock control circuit Falling-edge detector Transmit shift register shift completion flag (TSC) Transmit interrupt source selection bit Transmit interrupt request (TI) Shift clock P45 /TXD Transmit shift register Transmit buffer register Address 0018 16 Transmit buffer empty flag (TBE) Address 0019 16 Serial I/O1 status register Data bus Fig. 21 Block diagram of clock synchronous serial I/O1 Transfer shift clock (1/2 to 1/2048 of the internal clock, or an external clock) Serial output T XD D0 D1 D2 D3 D4 D5 D6 D7 Serial input R XD D0 D1 D2 D3 D4 D5 D6 D7 Receive enable signal S RDY1 Write signal to receive/transmit buffer register (address 0018 16) TBE = 0 TBE = 1 TSC = 0 RBF = 1 TSC = 1 Overrun error (OE) detection Notes 1 : The transmit interrupt (TI) can be selected to occur either when the transmit buffer register has emptied (TBE=1) or after the transmit shift operation has ended (TSC=1), by setting the transmit interrupt source selection bit (TIC) of the serial I/O1 control register. 2 : If data is written to the transmit buffer register when TSC=0, the transmit clock is generated continuously and serial data is output continuously from the T XD pin. 3 : The receive interrupt (RI) is set when the receive buffer full flag (RBF) becomes "1" . Fig. 22 Operation of clock synchronous serial I/O1 function 25 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER ter, but the two buffers have the same address in memory. Since the shift register cannot be written to or read from directly, transmit data is written to the transmit buffer, and receive data is read from the receive buffer. The transmit buffer can also hold the next data to be transmitted, and the receive buffer register can hold a character while the next character is being received. (2) Asynchronous Serial I/O (UART) Mode Clock asynchronous serial I/O mode (UART) can be selected by clearing the serial I/O mode selection bit of the serial I/O1 control register to "0". Eight serial data transfer formats can be selected, and the transfer formats used by a transmitter and receiver must be identical. The transmit and receive shift registers each have a buffer regis- Data bus Address 0018 16 P44 /RXD Serial I/O1 control register Receive buffer register OE Character length selection bit 7 bits STdetector Receive shift register Address 001A 16 Receive buffer full flag (RBF) Receive interrupt request (RI) 1/16 8 bits UART control register Address 001B 16 SP detector PE FE Clock control circuit Serial I/O synchronous clock selection bit P46 /SCLK BRG count source selection bit f(XIN ) (f(XCIN) in low-speed mode) 1/4 Frequency division ratio 1/(n+1) Baud rate generator Address 001C 16 ST/SP/PA generator Transmit shift register shift completion flag (TSC) 1/16 P45 /TXD Transmit shift register Transmit interrupt source selection bit Transmit interrupt request (TI) Character length selection bit Transmit buffer register Address 0018 16 Transmit buffer empty flag (TBE) Serial I/O status register Address 0019 16 Data bus Fig. 23 Block diagram of UART serial I/O1 Transmit or receive clock Transmit buffer write signal TBE=0 TSC=0 TBE=1 Serial output T XD TBE=0 TSC=1 TBE=1 ST D0 D1 SP ST D0 1 start bit 7 or 8 data bits 1 or 0 parity bit 1 or 2 stop bit (s) Receive buffer read signal Generated RBF=0 RBF=1 Serial input R XD ST D0 D1 D1 SP ST D0 D1 SP at 2nd bit in 2-stop-bit mode RBF=1 SP Notes 1 : Error flag detection occurs at the same time that the RBF flag becomes "1" (at 1st stop bit, during reception). 2 : The transmit interrupt (TI) can be selected to occur when either the TBE or TSC flag becomes "1" by the setting of the transmit interrupt source selection bit (TIC) of the serial I/O1 control register. 3 : The receive interrupt (RI) is set when the RBF flag becomes "1". 4 : After data is written to the transmit buffer register when TSC=1, 0.5 to 1.5 cycles of the data shift cycle is necessary until changing to TSC=0. Fig. 24 Operation of UART serial I/O1 function 26 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER [Transmit Buffer/Receive Buffer Register (TB/RB)] 001816 The transmit buffer register and the receive buffer register are located at the same address. The transmit buffer register is write-only and the receive buffer register is read-only. If a character bit length is 7 bits, the MSB of data stored in the receive buffer register is "0". [Serial I/O1 Status Register (SIO1STS)] 001916 The read-only serial I/O1 status register consists of seven flags (bits 0 to 6) which indicate the operating status of the serial I/O function and various errors. Three of the flags (bits 4 to 6) are valid only in UART mode. The receive buffer full flag (bit 1) is cleared to "0" when the receive buffer is read. If there is an error, it is detected at the same time that data is transferred from the receive shift register to the receive buffer register, and the receive buffer full flag is set. A write to the serial I/O1 status register clears all the error flags OE, PE, FE, and SE. Writing "0" to the serial I/O1 enable bit (SIOE) also clears all the status flags, including the error flags. All bits of the serial I/O1 status register are initialized to "0" at reset, but if the transmit enable bit (bit 4) of the serial I/O1 control register has been set to "1", the transmit shift register shift completion flag (bit 2) and the transmit buffer empty flag (bit 0) become "1". [Serial I/O1 Control Register (SIO1CON)] 001A16 The serial I/O1 control register contains eight control bits for the serial I/O1 function. [UART Control Register (UARTCON) ]001B 16 This is a 5 bit register containing four control bits, which are valid when UART is selected and set the data format of an data receiver/transfer, and one control bit, which is always valid and sets the output structure of the P4 5/TXD pin. [Baud Rate Generator(BRG)] 0016 16 The baud rate generator determines the baud rate for serial transfer. The baud rate generator divides the frequency of the count source by 1/(n + 1), where n is the value written to the baud rate generator. 27 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER b7 b0 Serial I/O1 status register (SIO1STS : address 0019 16) Transmit buffer empty flag (TBE) 0: Buffer full 1: Buffer empty b0 Serial I/O1 control register (SIO1CON : address 001A 16) BRG count source selection bit (CSS) 0: f(XIN) (f(XCIN ) in low-speed mode) 1: f(XIN)/4 (f(X CIN)/4 in low-speed mode) Transmit shift register shift completion flag (TSC) 0: Transmit shift in progress 1: Transmit shift completed Overrun error flag (OE) 0: No error 1: Overrun error SRDY1 output enable bit (SRDY) 0: P47 pin operates as ordinary I/O pin. 1: P47 pin operates as S RDY1 output pin. Parity error flag (PE) 0: No error 1: Parity error Transmit interrupt source selection bit (TIC) 0: Interrupt when transmit buffer has emptied 1: Interrupt when transmit shift operation is completed Framing error flag (FE) 0: No error 1: Framing error Transmit enable bit (TE) 0: Transmit disabled 1: Transmit enabled Summing error flag (SE) 0: OE U PE U FE =0 1: OE U PE U FE =1 Receive enable bit (RE) 0: Receive disabled 1: Receive enabled Not used (returns "1" when read) Serial I/O1 mode selection bit (SIOM) 0: Asynchronous serial I/O (UART) 1: Clock synchronous serial I/O UART control register (UARTCON : address 001B 16) Character length selection bit (CHAS) 0: 8 bits 1: 7 bits Parity enable bit (PARE) 0: Parity checking disabled 1: Parity checking enabled Parity selection bit (PARS) 0: Even parity 1: Odd parity Stop bit length selection bit (STPS) 0: 1 stop bit 1: 2 stop bits P45 /TXD P-channel output disable bit (POFF) 0: CMOS output (in output mode) 1: N-channel open-drain output (in output mode) Not used (return "1" when read) Fig. 25 Structure of serial I/O1 control registers 28 b0 Serial I/O1 synchronous clock selection bit (SCS) 0: BRG output divided by 4 when clock synchronous serial I/O is selected. BRG output divided by 16 when UART is selected. 1: External clock input when clock synchronous serial I/O is selected. External clock input divided by 16 when UART is selected. Receive buffer full flag (RBF) 0: Buffer empty 1: Buffer full b7 b7 Serial I/O1 enable bit (SIOE) 0: Serial I/O1 disabled (pins P44 -P47 operate as ordinary I/O pins) 1: Serial I/O1 enabled (pins P44 -P47 operate as serial I/O pins) MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Serial I/O2 b7 b0 The serial I/O2 function can be used only for clock synchronous serial I/O. For clock synchronous serial I/O2 the transmitter and the receiver must use the same clock. When the internal clock is used, transfer is started by a write signal to the serial I/O2 register. When an internal clock is selected as the synchronous clock of the serial I/O2, either P6 2 or P63 can be selected as an output pin of the synchronous clock. In this case, the pin that is not selected as an output pin of the synchronous clock functions as a port. Serial I/O2 control register (SIO2CON : address 001D16) Internal synchronous clock select bits b2 b1 b0 0 0 0: f(XIN)/8 (f(XCIN)/8 in low-speed mode) 0 0 1: f(XIN)/16 (f(XCIN)/16 in low-speed mode) 0 1 0: f(XIN)/32 (f(XCIN)/32 in low-speed mode) 0 1 1: f(XIN)/64 (f(XCIN)/64 in low-speed mode) 1 0 0: 1 0 1: Do not set 1 1 0: f(XIN)/128 (f(XCIN)/128 in low-speed mode) 1 1 1: f(XIN)/256 (f(XCIN)/256 in low-speed mode) Serial I/O2 port selection bit 0: I/O port 1: SOUT2,SCLK21/SCLK22 signal output [Serial I/O2 Control Register (SIO2CON)] 001D16 P61/SOUT2 P-channel output disable bit 0: CMOS output (in output mode) 1: N-channel open-drain output (in output mode) The serial I/O2 control register contains 8 bits which control various serial I/O2 functions. Transfer direction selection bit 0: LSB first 1: MSB first Synchronous clock selection bit 0: External clock 1: Internal clock Synchronous clock output pin selection bit 0: SCLK21 1: SCLK22 Fig. 26 Structure of serial I/O2 control register 1/8 Divider 1/16 f(XIN) (f(XCIN) in low-speed mode) Internal synchronous clock select bits 1/32 Data bus 1/64 1/128 1/256 P63 latch (Note) P63/SCLK22 Synchronous clock selection bit "1" SCLK2 Synchronous circuit "0" External clock P62 latch "0" P62/SCLK21 (Note) "1" Serial I/O counter 2 (3) Serial I/O2 interrupt request P61 latch "0" P61/SOUT2 "1" Serial I/O2 port selection bit P60/SIN2 Serial I/O shift register 2 (8) Note: It is selected by the synchronous clock selection bit, the synchronous clock output pin selection bit, and the serial I/O port selection bit. Fig. 27 Block diagram of serial I/O2 function 29 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Transfer clock (Note 1) Serial I/O2 register write signal (Note 2) Serial I/O2 output S OUT2 D0 D1 D2 D3 D4 D5 D6 D7 Serial I/O2 input S IN2 Serial I/O2 interrupt request bit set Notes 1: When the internal clock is selected as the transfer clock, the divide ratio can be selected by setting bits 0 to 2 of the serial I/O2 control register. 2: When the internal clock is selected as the transfer clock, the S OUT2 pin goes to high impedance after transfer completion. When the external clock is selected as the transfer clock, a content of the serial I/O shift register is continued to shift during inputting a transfer clock. The S OUT2 pin does not go to high impedance after transfer completion. Fig. 28 Timing of serial I/O2 function 30 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PULSE WIDTH MODULATION (PWM) PWM Operation The 3827 group has a PWM function with an 8-bit resolution, based on a signal that is the clock input XIN or that clock input divided by 2. When at least either bit 1 (PWM 0 output enable bit) or bit 2 (PWM1 output enable bit) of the PWM control register is set to "1", operation starts by initializing the PWM output circuit, and pulses are output starting at an "H". When one PWM output is enabled and that the other PWM output is enabled, PWM output which is enabled to output later starts pulse output from halfway. When the PWM register or PWM prescaler is updated during PWM output, the pulses will change in the cycle after the one in which the change was made. Data Setting The PWM output pin also functions as ports P50 and P51 . Set the PWM period by the PWM prescaler, and set the period during which the output pulse is an "H" by the PWM register. If PWM count source is f(XIN) and the value in the PWM prescaler is n and the value in the PWM register is m (where n = 0 to 255 and m = 0 to 255) : PWM period = 255 (n+1)/f(XIN) = 51 (n+1) s (when XIN = 5 MHz) Output pulse "H" period = PWM period m/255 = 0.2 (n+1) m s (when XIN = 5 MHz) 51 m (n+1) 255 s PWM output T = [51 (n+1)] s m: Contents of PWM register n : Contents of PWM prescaler T : PWM cycle (when f(X IN ) = 5 MHz) Fig. 29 Timing of PWM cycle Data bus PWM prescaler pre-latch PWM register pre-latch PWM1 enable bit Transfer control circuit PWM prescaler latch PWM register latch PWM prescaler PWM circuit Count source selection bit Port P56 "0" XIN 1/2 "1" PWM 0 enable bit Fig. 30 Block diagram of PWM function 31 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER b0 b7 PWM control register (PWMCON : address 002B16) Count source selection bit 0 : f(XIN) 1 : f(XIN)/2 PWM0 function enable bit 0 : PWM0 disabled 1 : PWM0 enabled PWM1 function enable bit 0 : PWM1 disabled 1 : PWM1 enabled Not used (return "0" when read) Fig. 31 Structure of PWM control register A PWM (internal) C B stop stop T T T2 Port PWM 0 output PWM 1 output Port Port Port PWM register write signal (Changes from "A" to "B" during "H" period) PWM prescaler write signal (Changes from "T" to "T2" during PWM period) PWM 0 function enable bit PWM 1 function enable bit When the contents of the PWM register or PWM prescaler have changed, the PWM output will change from the next period after the change. Fig. 32 PWM output timing when PWM register or PWM prescaler is changed 32 B = C T2 T MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER A-D CONVERTER [A-D Conversion Register (AD)] 003516 b7 b0 A-D control register (ADCON : address 0031 16 ) The A-D conversion register is a read-only register that contains the result of an A-D conversion. During A-D conversion, do not read this register. Analog input pin selection bits 0 0 0 : P60 /SIN2 /AN0 0 0 1 : P61 /SOUT2 /AN1 0 1 0 : P62 /SCLK21 /AN2 0 1 1 : P63 /SCLK22 /AN3 1 0 0 : P64 /AN4 1 0 1 : P65 /AN5 1 1 0 : P66 /AN6 1 1 1 : P67 /AN7 AD conversion completion bit 0 : Conversion in progress 1 : Conversion completed VREF input switch bit 0 : OFF 1 : ON AD external trigger valid bit 0 : A-D external trigger invalid 1 : A-D external trigger valid Interrupt source selection bit 0 : Interrupt request at A-D conversion completed 1 : Interrupt request at ADT input rising or falling Reference voltage input selection bit 0 : V REF 1 : P5 6 /DA1 [A-D Control Register (ADCON)] 0034 16 The A-D control register controls the A-D conversion process. Bits 0 to 2 are analog input pin selection bits. Bit 3 is an A-D conversion completion bit and "0" during A-D conversion, then changes to "1" when the A-D conversion is completed. Writing "0" to this bit starts the A-D conversion. Bit 4 controls the transistor which breaks the through current of the resistor ladder. When bit 5, which is the AD external trigger valid bit, is set to "1", A-D conversion is started even by a rising edge or falling edge of an ADT input. Set ports which share with ADT pins to input when using an A-D external trigger. [Comparison Voltage Generator] The comparison voltage generator divides the voltage between AVSS and VREF, and outputs the divided voltages. 8-bit read (Read only address 0032 16.) b7 [Channel Selector] The channel selector selects one of the input ports P6 7/AN7-P6 0/ AN 0, and inputs it to the comparator. (Address 0032 16) b0 b9 b8 b7 b6 b5 b4 b3 b2 10-bit read (Read address 0033 16 first.) b7 [Comparator and Control Circuit] The comparator and control circuit compares an analog input voltage with the comparison voltage and stores the result in the A-D conversion register. When an A-D conversion is completed, the control circuit sets the AD conversion completion bit and the AD interrupt request bit to "1". Note that the comparator is constructed linked to a capacitor, so set f(XIN) to at least 500 kHz during A-D conversion. Use a clock divided the main clock XIN as the internal clock . b0 (Address 003316 ) b9 b8 b7 (Address 0032 16) b0 b7 b6 b5 b4 b3 b2 b1 b0 Note: High-order 6 bits of address 0033 16 becomes "0" at reading. Fig. 33 Structure of A-D control register Data bus b0 b7 A-D control register P40/ADT 3 A-D control register P61/SOUT2/AN1 P62/SCLK21 /AN2 P63/SCLK22 /AN3 P64/AN4 P65/AN5 P66/AN6 Channel selector P60/SIN2/AN0 ADT/A-D interrupt request (H) Comparater A-D conversion register (L) A-D conversion register 10 Resistor ladder P67/AN7 AVSS VREF P56/DA 1 Fig. 34 A-D converter block diagram 33 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER D-A CONVERTER The 3827 group has an on-chip D-A converter with 8-bit resolution and 2 channels (DAi (i=1, 2)). The D-A converter is performed by setting the value in the D-A conversion register. The result of D-A converter is output from DAi pin. When using the D-A converter, the corresponding port direction register bit (P5 6 /DA1, P5 7/DA 2) should be set to "0" (input status). The output analog voltage V is determined by the value n (base 10) in the D-A conversion register as follows: b7 b0 D-A control register (DACON : address 0036 16) DA1 output enable bit/DA 1 V REF ON/OFF switch DA2 output enable bit/DA 2 V REF ON/OFF switch Not used (return "0" when read) V=VREF n/256 (n=0 to 255) Where VREF is the reference voltage. 0 : Output disabled/OFF 1 : Output enabled/ON At reset, the D-A conversion registers are cleared to "0016", the DAi output enable bits are cleared to "0", and DAi pin goes to high impedance state. The DA output is not buffered, so connect an external buffer when driving a low-impedance load. Fig. 35 Structure of D-A control register Data bus D-A1 conversion register (0034 16) D-A2 conversion register (0035 16) D-A i conversion register (8) DA i output enable bit R-2R resistor ladder Fig. 36 Block diagram of D-A converter VREF Internal: D-A output External: V REF Reference voltage input select switch Resistor ladder VREF input ON/OFF switch D-A1 output (P56) A-D conversion register (10 bits) D-A1 output enable switch D-A1 VREF ON/OFF switch R-2R resistor ladder D-A1 conversion register (8 bits) D-A2 output enable switch D-A2 V REF ON/OFF switch D-A2 output R-2R resistor ladder (P5 7) Fig. 37 A-D converter, D-A converter block diagram 34 D-A2 conversion register (8 bits) P56/DA 1 P57/DA 2 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER LCD DRIVE CONTROL CIRCUIT The 3827 group has the built-in Liquid Crystal Display (LCD) drive control circuit consisting of the following. LCD display RAM Segment output enable register LCD mode register Voltage multiplier Selector Timing controller Common driver Segment driver Bias control circuit A maximum of 40 segment output pins and 4 common output pins can be used. b7 Up to 160 pixels can be controlled for LCD display. When the LCD enable bit is set to "1" after data is set in the LCD mode register, the segment output enable register and the LCD display RAM, the LCD drive control circuit starts reading the display data automatically, performs the bias control and the duty ratio control, and displays the data on the LCD panel. Table 7 Maximum number of display pixels at each duty ratio Duty ratio 2 3 4 Maximum number of display pixel 80 dots or 8 segment LCD 10 digits 120 dots or 8 segment LCD 15 digits 160 dots or 8 segment LCD 20 digits b0 Segment output enable register (SEG : address 0038 16) Segment output enable bit 0 0 : Output ports P3 0 -P35 1 : Segment output SEG 18-SEG23 Segment output enable bit 1 0 : Output ports P3 6 , P37 1 : Segment output SEG 24,SEG25 Segment output enable bit 2 0 : I/O ports P0 0-P05 1 : Segment output SEG 26-SEG31 Segment output enable bit 3 0 : I/O ports P0 6,P07 1 : Segment output SEG 32,SEG33 Segment output enable bit 4 0 : I/O port P1 0 1 : Segment output SEG 34 Segment output enable bit 5 0 : I/O ports P1 1-P15 1 : Segment output SEG 35-SEG39 LCD output enable bit 0 : Disable 1 : Enable Not used (return "0" when read) (Do not write "1" to this bit) b7 b0 LCD mode register (LM : address 0039 16) Duty ratio selection bits 0 0 : Not used 0 1 : 2 duty (use COM 0 , COM1 ) 1 0 : 3 duty (use COM 0 -COM2 ) 1 1 : 4 duty (use COM 0 -COM3 ) Bias control bit 0 : 1/3 bias 1 : 1/2 bias LCD enable bit 0 : LCD OFF 1 : LCD ON Voltage multiplier control bit 0 : Voltage multiplier disabled 1 : Voltage multiplier enabled LCD circuit divider division ratio selection bits 0 0 : 1 division of clock input 0 1 : 2 division of clock input 1 0 : 4 division of clock input 1 1 : 8 division of clock input LCDCK count source selection bit (Note) 0 : f(XCIN )/32 1 : f(XIN )/8192 (f(X CIN)/8192 in low-speed mode) Note : LCDCK is a clock for a LCD timing controller. Fig. 38 Structure of LCD mode register 35 36 Fig. 39 Block diagram of LCD controller/driver Level shift Level shift SEG0 SEG1 SEG2 SEG3 Segment Segment Segment Segment driver driver driver driver Level shift P30 /SEG18 Level shift Bias control VCC Common driver Level Shift Common driver Level Shift Common driver Level Shift COM0 COM1 COM2 COM3 Common driver Level Shift 2 Timing controller 2 LCD circuit divider division ratio selection bits Duty ratio selection bits LCD enable bit LCD output enable bit Bias control bit VSS VL1 VL2 VL3 C1 C2 Voltage multiplier control bit LCD display RAM P14/SEG38 P15/SEG39 Segment Segment driver driver Level shift Selector Selector Selector Selector Selector Selector Level shift Address 0053 16 Address 004116 Address 0040 16 Data bus LCDCK LCD divider "1" f(X IN)/8192 (f(XCIN )/8192 in low-speed mode) LCDCK count source selection bit "0" f(XCIN )/32 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER VOLTAGE MULTIPLIER (3 TIMES) Bias Control and Applied Voltage to LCD Power Input Pins The voltage multiplier performs threefold boosting. This circuit inputs a reference voltage for boosting from LCD power input pin VL1. (However, when using a 1/2 bias, connect V L1 and V L2 and apply voltage by external resistor division.) Set each bit of the segment output enable register and the LCD mode register in the following order for operating the voltage multiplier. 1. Set the segment output enable bits (bits 0 to 5) of the segment output enable register to "0" or "1." 2. Set the duty ratio selection bits (bits 0 and 1), the bias control bit (bit 2), the LCD circuit divider division ratio selection bits (bits 5 and 6), and the LCDCK count source selection bit (bit 7) of the LCD mode register to "0" or "1." 3. Set the LCD output enable bit (bit 6) of the segment output enable register to "1." 4. Set the voltage multiplier control bit (bit 4) of the LCD mode register to "1." When voltage is input to the VL1 pin during operating the voltage multiplier, voltage that is twice as large as VL1 occurs at the VL2 pin, and voltage that is three times as large as VL1 occurs at the VL3 pin. When using the voltage multiplier, apply 1.3 V Voltage 2.3 V to the VL1 pin. When not using the voltage multiplier,apply proper voltage to the LCD power input pins (VL1 -VL3 ). Then set the LCD output enable bit to "1." When the LCD output enable bit is set to "0," the VCC voltage is applied to the VL3 pin inside of this microcomputer. The voltage multiplier control bit (bit 4 of the LCD mode register) controls the voltage multiplier. To the LCD power input pins (VL1-VL3 ), apply the voltage shown in Table 8 according to the bias value. Select a bias value by the bias control bit (bit 2 of the LCD mode register). Table 8 Bias control and applied voltage to V L1-VL3 Bias value 1/3 bias 1/2 bias Voltage value VL3 =VLCD VL2 =2/3 VLCD VL1 =1/3 VLCD VL3 =VLCD VL2 =VL1 =1/2 VLCD Note 1: V LCD is the maximum value of supplied voltage for the LCD panel. Contrast control VCC VL3 Contrast control VCC VL3 VL3 R1 VL2 VL2 C2 C2 R4 VL2 Open C2 Open C1 Open R2 C1 C1 VL1 VL1 Open VL1 R3 R5 PXX R1=R2=R3 1/3 bias when using the voltage multiplier 1/3 bias when not using the voltage multiplier R4=R5 1/2 bias Fig. 40 Example of circuit at each bias 37 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Common Pin and Duty Ratio Control ment/output port pins are pulled up to the VCC (=V L3) voltage in the high impedance condition. The segment/I/O port pins are set to input ports, and V CC (=VL3 ) is applied to them by pull-up resistor. The common pins (COM 0-COM 3) to be used are determined by duty ratio. Select duty ratio by the duty ratio selection bits (bits 0 and 1 of the LCD mode register). When releasing from reset, the VCC (VL3) voltage is output from the common pins. LCD Display RAM Address 004016 to 005316 is the designated RAM for the LCD display. When "1" are written to these addresses, the corresponding segments of the LCD display panel are turned on. Table 9 Duty ratio control and common pins used Duty ratio Duty ratio selection bit LCD Drive Timing Common pins used Bit 1 Bit 0 2 0 1 COM0, COM1 (Note 1) 3 1 COM0-COM2 (Note 2) 4 1 0 1 The LCDCK timing frequency (LCD drive timing) is generated internally and the frame frequency can be determined with the following equation; COM0-COM3 (frequency of count source for LCDCK) (divider division ratio for LCD) Notes1: COM2 and COM3 are open. 2: COM3 is open. f(LCDCK) = Segment Signal Output Pin Frame frequency = f(LCDCK) (duty ratio) 3 0 Segment signal output pins are classified into the segment-only pins (SEG 0 -SEG 17 ), the segment/output port pins (SEG 18- SEG25 ), and the segment/I/O port pins (SEG 26-SEG 39). Segment signals are output according to the bit data of the LCD RAM corresponding to the duty ratio. After reset release, a VCC (=V L3) voltage is output to the segment-only pins and the seg- Bit 7 6 5 4 2 1 address 004016 SEG1 SEG0 004116 SEG3 SEG2 004216 SEG5 SEG4 004316 SEG7 SEG6 004416 SEG9 SEG8 004516 SEG11 SEG10 004616 SEG13 SEG12 004716 SEG15 SEG14 004816 SEG17 SEG16 004916 SEG19 SEG18 004A16 SEG21 SEG20 004B16 SEG23 SEG22 004C16 SEG25 SEG24 004D16 SEG27 SEG26 004E16 SEG29 SEG28 004F16 SEG31 SEG30 005016 SEG33 SEG32 005116 SEG35 SEG34 005216 SEG37 SEG36 005316 SEG39 SEG38 COM3 COM 2 COM 1 COM 0 COM 3 COM 2 COM 1 COM0 Fig. 41 LCD display RAM map 38 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Internal signal LCDCK timing 1/4 duty Voltage level VL3 VL2=VL1 VSS COM0 COM1 COM2 COM3 VL3 VSS SEG0 OFF COM3 ON COM2 COM1 OFF COM0 COM3 ON COM2 COM1 COM0 1/3 duty VL3 VL2=VL1 VSS COM0 COM1 COM2 VL3 VSS SEG0 ON COM0 OFF COM2 ON COM1 OFF COM0 COM2 ON COM1 OFF COM0 COM2 1/2 duty VL3 VL2=VL1 VSS COM0 COM1 VL3 VSS SEG0 ON COM1 OFF COM0 ON COM1 OFF COM0 ON COM1 OFF COM0 ON COM1 OFF COM0 Fig. 42 LCD drive waveform (1/2 bias) 39 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Internal signal LCDCK timing 1/4 duty Voltage level VL3 VL2 VL1 VSS COM0 COM1 COM2 COM3 VL3 SEG0 VSS OFF COM3 ON COM2 COM1 OFF COM0 COM3 ON COM2 COM1 COM0 1/3 duty VL3 VL2 VL1 VSS COM0 COM1 COM2 VL3 SEG0 VSS ON COM0 OFF COM2 ON COM1 OFF COM0 COM2 ON COM1 OFF COM0 COM2 1/2 duty VL3 VL2 VL1 VSS COM0 COM1 VL3 SEG0 VSS ON COM1 OFF COM0 Fig. 43 LCD drive waveform (1/3 bias) 40 ON COM1 OFF COM0 ON COM1 OFF COM0 ON COM1 OFF COM0 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER value of high-order 6-bit counter value of STP instruction disable bit value of count source selection bit. WATCHDOG TIMER The watchdog timer gives a mean of returning to the reset status when a program cannot run on a normal loop (for example, because of a software runaway). The watchdog timer consists of an 8-bit watchdog timer L and a 6bit watchdog timer H. At reset or writing to the watchdog timer control register (address 0037 16), the watchdog timer is set to "3FFF 16." When any data is not written to the watchdog timer control register (address 003716 ) after reset, the watchdog timer is in stop state. The watchdog timer starts to count down from "3FFF16 " by writing an optional value into the watchdog timer control register (address 0037 16) and an internal reset occurs at an underflow. Accordingly, programming is usually performed so that writing to the watchdog timer control register (address 003716) may be started before an underflow. The watchdog timer does not function when an optional value have not written to the watchdog timer control register (address 003716 ). When address 003716 is read, the following values are read: Data bus "FF16" is set when watchdog timer is written to. XCIN "1" Internal system clock selection bit "0" When bit 6 of the watchdog timer control register (address 003716 ) is set to "0," the STP instruction is valid. The STP instruction is disabled by rewriting this bit to "1." At this time, if the STP instruction is executed, it is processed as an undefined instruction, so that a reset occurs inside. This bit cannot be rewritten to "0" by programming. This bit is "0" immediately after reset. The count source of the watchdog timer becomes the system clock divided by 8. The detection time in this case is set to 8.19 s at XCIN = 32 kHz and 65.536 ms at XIN = 4 MHz. However, count source of high-order 6-bit timer can be connected to a signal divided system clock by 8 directly by writing the bit 7 of the watchdog timer control register (address 003716) to "1." The detection time in this case is set to 32 ms at XCIN = 32 kHz and 256 s at XIN = 4 MHz. There is no difference in the detection time between the middle-speed mode and the high-speed mode. Watchdog timer Watchdog timer count source selection bit "0" L (8) 1/16 Watchdog timer "1" H (6) "3F16" is set when watchdog timer is written to. XIN Undefined instruction Reset STP instruction disable bit STP instruction RESETIN Reset circuit Internal reset Reset release time wait Fig. 44 Block diagram of watchdog timer b7 b0 Watchdog timer register (address 003716) WDTCON Watchdog timer H (for read-out of high-order 6 bit) "3FFF16" is set to the watchdog timer by writing values to this address. STP instruction disable bit 0 STP instruction enabled 1 : STP instruction disabled Watchdog timer H count source selection bit 0 : Internal system clock/2048 (f(XIN)/4096) 1 : Internal system clock/8 (f(XIN)/16) Fig. 45 Structure of watchdog timer control register f(XIN) Internal reset signal 2ms (f(XIN) = 4MHZ) Watchdog timer detection Fig. 46 Timing of reset output 41 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER TOUT/ CLOCK OUTPUT FUNCTION The internal system clock or timer 2 divided by 2 (TOUT output) can be output from port P43 by setting the TOUT/ output control bit (bit 1) of the timer 123 mode register and the TOUT/ output control register. Set bit 3 of the port P4 direction register to "1" when outputting the clock. b7 b0 TOUT / output control register (CKOUT : address 002A 16) TOUT / output control bit 0 : clock output 1 : TOUT output Not used (return "0" when read) b7 b0 Timer 123 mode register (T123M : address 0029 16) TOUT output active edge switch bit 0 : Start on "H" output 1 : Start on "L" output TOUT / output control bit 0 : TOUT / output disable 1 : TOUT / output enable Timer 2 write control bit 0 : Write data in latch and timer 1 : Write data in latch only Timer 2 count source selection bit 0 : Timer 1 output 1 : f(XIN )/16 (or f(XCIN )/16 in low-speed mode ) Timer 3 count source selection bit 0 : Timer 1 output 1 : f(XIN )/16 (or f(XCIN )/16 in low-speed mode ) Timer 1 count source selection bit 0 : f(XIN )/16 (or f(XCIN )/16 in low-speed mode ) 1 : f(XCIN ) Not used (return "0" when read) : Internal clock is f(XCIN)/2 in low-speed mode. Fig. 47 Structure of TOUT / output-related register 42 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER RESET CIRCUIT Poweron To reset the microcomputer, RESET pin should be held at an "L" level for 2 s or more. Then the RESET pin is returned to an "H" level (the power source voltage should be between VCC(min.) and 5.5 V, and the oscillation should be stable), reset is released. After the reset is completed, the program starts from the address contained in address FFFD 16 (high-order byte) and address FFFC 16 (low-order byte). Make sure that the reset input voltage is less than 0.2 V CC for V CC of VCC (min.). RESET (Note) Power source voltage 0V VCC Reset input voltage 0V 0.2VCC Note : Reset release voltage ; VCC=VCC(min.) RESET VCC Power source voltage detection circuit Fig. 48 Reset Circuit Example XIN RESET Internal reset Reset address from vector table Address ? ? ? Data ? FFFC ADL FFFD ADH, ADL ADH SYNC XIN : about 8200 cycles Notes 1: The frequency relation of f(X IN) and f() is f(XIN) = 8 * f(). 2: The question marks (?) indicate an undefined state that depends on the previous state. Fig. 49 Reset Sequence 43 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Address Register contents Address 000116 0016 (28) A-D control register 003116 0816 (2) Port P1 direction register 000316 0016 003216 XX16 (3) Port P2 direction register 000516 0016 003316 XX16 (4) Port P3 output control register 000716 0016 (29) A-D conversion register (low-order) (30) A-D conversion register (high-order) (31) D-A1 conversion register 003416 0016 (5) Port P4 direction register 000916 0016 (32) D-A2 conversion register 003516 0016 (6) Port P5 direction register 000B16 0016 (33) D-A control register 003616 0016 (7) Port P6 direction register 000D16 0016 (34) Watchdog timer control register 003716 0 0 1 1 1 1 1 1 (8) Port P7 direction register 000F16 0016 (35) Segment output enable register 003816 0016 (9) Key input control register 001516 0016 (36) LCD mode register 003916 0016 (10) PULL register A 001616 3F16 (37) Interrupt edge selection register 003A16 0016 (11) PULL register B 001716 0016 (38) CPU mode register 003B16 0 1 0 0 1 0 0 0 (12) Serial I/O1 status register 001916 1 0 0 0 0 0 0 0 (39) Interrupt request register 1 003C16 0016 (13) Serial I/O1 control register 001A16 (40) Interrupt request register 2 003D16 0016 (14) UART control register 001B16 1 1 1 0 0 0 0 0 (41) Interrupt control register 1 003E16 0016 (15) Serial I/O2 control register 001D16 0016 (42) Interrupt control register 2 003F16 0016 (16) Timer X (low-order) 002016 FF16 (43) Processor status register (17) Timer X (high-order) 002116 FF16 (44) Program counter (18) Timer Y (low-order) 002216 FF16 (19) Timer Y (high-order) 002316 FF16 (45) Watchdog timer (high-order) 3F16 (20) Timer 1 002416 FF16 (46) Watchdog timer (low-order) FF16 (21) Timer 2 002516 0116 (22) Timer 3 002616 FF16 (23) Timer X mode register 002716 0016 (24) Timer Y mode register 002816 0016 (25) Timer 123 mode register 002916 0016 (26) TOUT/ output control register 002A16 0016 (27) PWM control register 002B16 0016 0016 (PS) 1 (PCH) Contents of address FFFD 16 (PCL) Contents of address FFFC 16 Note: The contents of all other register and RAM are undefined after reset, so they must be initialized by software. : Undefined Fig. 50 Initial status at reset 44 Register contents (1) Port P0 direction register MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER CLOCK GENERATING CIRCUIT The 3827 group has two built-in oscillation circuits. An oscillation circuit can be formed by connecting a resonator between XIN and XOUT (XCIN and X COUT). Use the circuit constants in accordance with the resonator manufacturer's recommended values. No external resistor is needed between XIN and XOUT since a feed-back resistor exists on-chip. However, an external feed-back resistor is needed between XCIN and XCOUT. To supply a clock signal externally, input it to the XIN pin and make the XOUT pin open. The sub-clock XCIN-X COUT oscillation circuit cannot directly input clocks that are externally generated. Accordingly, be sure to cause an external resonator to oscillate. Immediately after poweron, only the XIN oscillation circuit starts oscillating, and XCIN and X COUT pins go to high impedance state. Oscillation Control (1) Stop Mode Frequency Control (1) Middle-speed Mode If the STP instruction is executed, the internal clock stops at an "H" level, and X IN and X CIN oscillators stop. The value set to the timer latch 1 and the timer latch 2 is loaded automatically to the timer 1 and the timer 2. Thus, a value generated time for stabilizing oscillation should be set to the timer 1 latch and the timer 2 latch (low-order 8 bits for the timer 1, high-order 8 bits for the timer 2) before executing the STP instruction. Either X IN or X CIN divided by 16 is input to timer 1 as count source, and the output of timer 1 is connected to timer 2. The bits of the timer 123 mode register except bit 4 are cleared to "0," Set the timer 1 and timer 2 interrupt enable bits to disabled ("0") before executing the STP instruction. Oscillator restarts at reset or when an external interrupt is received, but the internal clock is not supplied to the CPU until timer 2 underflows..This allows timer for the clock circuit oscillation to stabilize. The internal clock is the frequency of XIN divided by 8. After reset, this mode is selected. (2) Wait Mode (2) High-speed Mode The internal clock is half the frequency of XIN . (3) Low-speed Mode The internal clock is half the frequency of XCIN. A low-power consumption operation can be realized by stopping the main clock X IN in this mode. To stop the main clock, set bit 5 of the CPU mode register to "1". When the main clock XIN is restarted, set enough time for oscillation to stabilize by programming. Note: If you switch the mode between middle/high-speed and lowspeed, stabilize both X IN and X CIN oscillations. The sufficient time is required for the sub-clock to stabilize, especially immediately after poweron and at returning from stop mode. When switching the mode between middle/highspeed and low-speed, set the frequency on condition that f(XIN)>3f(XCIN ). If the WIT instruction is executed, the internal clock stops at an "H" level. The states of XIN and XCIN are the same as the state before the executing the WIT instruction. The internal clock restarts at reset or when an interrupt is received. Since the oscillator does not stop, normal operation can be started immediately after the clock is restar ted. XCIN XCOUT Rf XIN Rd CCOUT CCIN XOUT CIN COUT Fig. 51 Ceramic resonator circuit XCIN Rf CCIN XCOUT XIN XOUT Open Rd CCOUT External oscillation circuit VCC VSS Fig. 52 External clock input circuit 45 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER XCOUT XCIN XIN XOUT Low-speed mode "0" 1/2 "1" Middle-/High-speed mode Timer 2 count source selection bit Timer 1 count source selection bit Internal system clock selection bit (Note) "1" Timer 1 1/2 1/4 "0" "0" Timer 2 "1" Main clock division ratio selection bit Middle-speed mode "1" Main clock stop bit Q S S R STP instruction WIT instruction Q R Reset Interrupt disable flag I Interrupt request Note: When selecting the X C oscillation, set the port X C switch bit to "1" . Fig. 53 Clock generating circuit block diagram 46 Timing (Internal clock) "0" High-speed mode or Low-speed mode Q S R STP instruction MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Reset " "0 CM " "1 M6 C " "1 " "0 CM7=0(8 MHz selected) CM6=0(High-speed) CM5=0(8 MHz oscillating) CM4=0(32 kHz stopped) C "0 M4 " CM "1 " 6 "1 " "0 " Middle-speed mode (f() =1 MHz) CM 6 "1" "0" CM 6 "1" "0" High-speed mode (f() =4 MHz) CM7=0(8 MHz selected) CM6=0(High-speed) CM5=0(8 MHz oscillating) CM4=1(32 kHz oscillating) CM7 "1" CM 7 "1" "0" "0" CM7=0(8 MHz selected) CM6=1(Middle-speed) CM5=0(8 MHz oscillating) CM4=1(32 kHz oscillating) "0" CM7=1(32 kHz selected) CM6=1(Middle-speed) CM5=0(8 MHz oscillating) CM4=1(32 kHz oscillating) " CM 5 "1" 5 Low-power dissipation mode (f() =16 kHz) CM7=1(32 kHz selected) CM6=1(Middle-speed) CM5=1(8 MHz stopped) CM4=1(32 kHz oscillating) Low-speed mode (f() =16 kHz) CM " "1 M6 C " "1 "0 0" " "1 " CM7=1(32 kHz selected) CM6=0(High-speed) CM5=0(8 MHz oscillating) CM4=1(32 kHz oscillating) C "0 M5 " CM 6 "1 " "0 " CM 6 "1" "0" Low-speed mode (f() =16 kHz) "0" CM5 "1" CM4 "1" 4 High-speed mode (f() =4 MHz) "0" "0" "0" CM7=0(8 MHz selected) CM6=1(Middle-speed) CM5=0(8 MHz oscillating) CM4=0(32 kHz stopped) CM4 "1" CM 6 "1" Middle-speed mode (f() =1 MHz) Low-power dissipation mode (f() =16 kHz) CM7=1(32 kHz selected) CM6=0(High-speed) CM5=1(8 MHz stopped) CM4=1(32 kHz oscillating) b7 b4 CPU mode register (CPUM : address 003B 16) CM 4 : Port Xc switch bit 0: I/O port function 1: X CIN -XCOUT oscillating function CM 5 : Main clock (XIN -XOUT ) stop bit 0: Oscillating 1: Stopped CM 6 : Main clock division ratio selection bit 0: f(X IN)/2 (high-speed mode) 1: f(X IN)/8 (middle-speed mode) CM 7 : Internal system clock selection bit 0: X IN -XOUT selected (middle-/high-speed mode) 1: X CIN -XCOUT selected (low-speed mode) Notes 1 : Switch the mode by the allows shown between the mode blocks. (Do not switch between the mode directly without an allow.) 2 : The all modes can be switched to the stop mode or the wait mode and returned to the source mode when the stop mode or the wait mode is ended. 3 : Timer and LCD operate in the wait mode. 4 : When the stop mode is ended, wait time can be set by connecting timer 1 and timer 2 in middle-/high-speed mode. 5 : When the stop mode is ended, wait time can be set by connecting timer 1 and timer 2 in low-speed mode. 6 : Wait until oscillation stabilizes after oscillating the main clock X IN before the switching from the low-speed mode to middle-/high-speed mode. 7 : The example assumes that 8 MHz is being applied to the X IN pin and 32 kHz to the X CIN pin. indicates the internal clock. Fig. 54 State transitions of system clock 47 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER NOTES ON PROGRAMMING Processor Status Register The contents of the processor status register (PS) after a reset are undefined, except for the interrupt disable flag (I) which is "1". After a reset, initialize flags which affect program execution. In particular, it is essential to initialize the index X mode (T) and the decimal mode (D) flags because of their effect on calculations. Interrupt The contents of the interrupt request bits do not change immediately after they have been written. After writing to an interrupt request register, execute at least one instruction before performing a BBC or BBS instruction. Decimal Calculations * To calculate in decimal notation, set the decimal mode flag (D) to "1", then execute an ADC or SBC instruction. After executing an ADC or SBC instruction, execute at least one instruction before executing a SEC, CLC, or CLD instruction. * In decimal mode, the values of the negative (N), overflow (V), and zero (Z) flags are invalid. Timers If a value n (between 0 and 255) is written to a timer latch, the frequency division ratio is 1/(n + 1). Multiplication and Division Instructions The index mode (T) and the decimal mode (D) flags do not affect the MUL and DIV instruction. The execution of these instructions does not change the contents of the processor status register. Ports The contents of the port direction registers cannot be read. The following cannot be used: * The data transfer instruction (LDA, etc.) * The operation instruction when the index X mode flag (T) is "1" * The addressing mode which uses the value of a direction register as an index * The bit-test instruction (BBC or BBS, etc.) to a direction register * The read-modify-write instruction (ROR, CLB, or SEB, etc.) to a direction register Use instructions such as LDM and STA, etc., to set the port direction registers. 48 Serial I/O In clock synchronous serial I/O, if the receive side is using an external clock and it is to output the SRDY signal, set the transmit enable bit, the receive enable bit, and the SRDY output enable bit to "1". Serial I/O1 continues to output the final bit from the TXD pin after transmission is completed. In serial I/O2, the SOUT2 pin goes to high impedance state after transmission is completed. A-D Converter The comparator uses internal capacitors whose charge will be lost if the clock frequency is too low. Make sure that f(XIN ) is at least 500 kHz during an A-D conversion. Do not execute the STP or WIT instruction during an A-D conversion. Instruction Execution Time The instruction execution time is obtained by multiplying the frequency of the internal clock by the number of cycles needed to execute an instruction. The number of cycles required to execute an instruction is shown in the list of machine instructions. The frequency of the internal clock is half of the X IN frequency. MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER DATA REQUIRED FOR MASK ORDERS ROM PROGRAMMING METHOD The following are necessary when ordering a mask ROM production: (1) Mask ROM Order Confirmation Form (2) Mark Specification Form (3) Data to be written to ROM, in EPROM form (three identical copies) The built-in PROM of the blank One Time PROM version and builtin EPROM version can be read or programmed with a general-purpose PROM programmer using a special programming adapter. Set the address of PROM programmer in the user ROM area. DATA REQUIRED FOR ROM WRITING ORDERS The following are necessary when ordering a ROM writing: (1) ROM Writing Confirmation Form (2) Mark Specification Form (3) Data to be written to ROM, in EPROM form (three identical copies) Table 10 Special programming adapter Package Name of Programming Adapter 100PFB-A Under development (PCA4738H-100A) 100P6Q-A PCA4738G-100A 100P6S-A PCA4738F-100A 100D0 PCA4738L-100A The PROM of the blank One Time PROM version is not tested or screened in the assembly process and following processes. To ensure proper operation after programming, the procedure shown in Figure 55 is recommended to verify programming. Programming with PROM programmer Screening (Caution) (150C for 40 hours) Verification with PROM programmer Functional check in target device Caution : The screening temperature is far higher than the storage temperature. Never expose to 150 C exceeding 100 hours. Fig. 55 Programming and testing of One Time PROM version 49 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER ELECTRICAL CHARACTERISTICS ABSOLUTE MAXIMUM RATINGS Table 11 Absolute maximum ratings Symbol VCC VI VI VI VI VI VI VI VI VO Parameter Power source voltage Input voltage P00-P07 , P10-P17, P20 -P27, P41-P47 , P50-P57, P60 -P67 Input voltage P40, P7 1-P77 Input voltage P70 Input voltage VL1 Input voltage VL2 Input voltage VL3 Input voltage C1, C2 Input voltage RESET, X IN Output voltage C 1, C2 VO Output voltage P0 0-P07, P10-P15 , P30-P37 VO VO VO VO VO Pd Topr Tstg Output voltage P16, P17 , P20-P27, P41 -P47, P50-P57 , P60-P67, P80, P8 1 Output voltage P4 0, P71-P77 Output voltage VL3 Output voltage VL2, SEG 0-SEG17 Output voltage X OUT Power dissipation Operating temperature Storage temperature Conditions All voltages are based on VSS . Output transistors are cut off. At output port At segment output Ta = 25C Ratings -0.3 to 7.0 Unit V -0.3 to VCC +0.3 V -0.3 to 7.0 -0.3 to VCC +0.3 -0.3 to VL2 VL1 to VL3 VL2 to 7.0 -0.3 to 7.0 -0.3 to VCC +0.3 -0.3 to 7.0 -0.3 to VCC -0.3 to VL3 V V V V V V V V V V -0.3 to VCC +0.3 V -0.3 to 7.0 -0.3 to 7.0 -0.3 to VL3 -0.3 to VCC +0.3 300 -20 to 85 -40 to 125 V V V V mW C C RECOMMENDED OPERATING CONDITIONS Table 12 Recommended operating conditions (V CC = 2.5 to 5.5 V, Ta = -20 to 85C, unless otherwise noted) Symbol Parameter High-speed mode f(X IN) = 8 MHz Middle-speed mode f(XIN) = 8 MHz Low-speed mode VCC Power source voltage VSS VREF AVSS VIA Power source voltage A-D, D-A conversion reference voltage Analog power source voltage Analog input voltage AN 0-AN 7 "H" input voltage P00-P07 , P56, P6 1, "H" input voltage P20-P27 , P62, P6 3, RESET "H" input voltage XIN "H" input voltage "L" input voltage P00-P07 , P56, P6 1, "L" input voltage P20-P27 , P62, P6 3, "L" input voltage RESET "L" input voltage XIN VIH VIH VIH VIH VIL VIL VIL VIL 50 Min. 4.0 2.2 2.2 Limits Typ. 5.0 5.0 5.0 0 Max. 5.5 5.5 5.5 AVSS VCC 0.7 VCC VCC V 0.8 VCC VCC V 0.8 VCC 0.8 VCC VCC VCC V V 0 0.3 VCC V 0 0.2 VCC V 0 0 0.2 VCC 0.2 VCC V V VCC+0.3 0 P10-P17, P40 , P43, P45 , P47, P50-P53 , P64-P67, P7 1-P77 P41, P42, P4 4, P46, P54 , P55, P57 , P60, P70 V V V V V 2.7 P10-P17, P40 , P43, P45 , P47, P50-P53 , P64-P67, P7 1-P77 P41, P42, P4 4, P46, P54 , P55, P57 , P60, P70 Unit MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Table 13 Recommended operating conditions (VCC = 2.2 to 5.5 V, Ta = -20 to 85C, unless otherwise noted) Symbol Parameter I OH(peak) I OH(peak) I OL(peak) I OL(peak) I OL(peak) I OH(avg) I OH(avg) I OL(avg) I OL(avg) I OL(avg) I OH(peak) "H" total peak output current "H" total peak output current "L" total peak output current "L" total peak output current "L" total peak output current "H" total average output current "H" total average output current "L" total average output current "L" total average output current "L" total average output current "H" peak output current I OH(peak) "H" peak output current I OL(peak) "L" peak output current I OL(peak) "L" peak output current I OL(peak) I OH(avg) I OH(avg) I OL(avg) "L" peak output current "H" average output current "H" average output current "L" average output current I OL(avg) "L" average output current I OL(avg) "L" average output current P00-P07, P1 0-P17, P20-P27 , P30-P37 (Note 1) P41-P47, P5 0-P57, P60-P67 (Note 1) P00-P07, P1 0-P17, P20-P27 , P30-P37 (Note 1) P41-P47, P5 0-P57, P60-P67 (Note 1) P40, P71 -P77 (Note 1) P00-P07, P1 0-P17, P20-P27 , P30-P37 (Note 1) P41-P47, P5 0-P57, P60-P67 (Note 1) P00-P07, P1 0-P17, P20-P27 , P30-P37 (Note 1) P41-P47, P5 0-P57, P60-P67 (Note 1) P40, P71 -P77 (Note 1) P00-P07, P1 0-P15, P30-P37 (Note 2) P16, P17 , P20-P27, P41 -P47, P50-P57, P6 0-P67 (Note 2) P00-P07, P1 0-P15, P30-P37 (Note 2) P16, P17 , P20-P27, P41 -P47, P50-P57, P6 0-P67 (Note 2) P40, P71 -P77 (Note 2) P00-P07, P1 0-P15, P30-P37 (Note 3) P16, P17 , P20-P27, P41 -P47, P50-P57, P6 0-P67 P00-P07, P1 0-P15, P30-P37 (Note 3) P16, P17 , P20-P27, P41 -P47, P50-P57, P6 0-P67 (Note 3) P40, P71 -P77 (Note 3) Min. Limits Typ. Max. Unit -20 -20 20 20 80 -10 -10 10 10 40 -1.0 mA mA mA mA mA mA mA mA mA mA mA -5.0 mA 5.0 mA 10 mA 20 -0.5 -2.5 2.5 mA mA mA mA 5.0 mA 10 mA Notes1: The total output current is the sum of all the currents flowing through all the applicable ports. The total average current is an average value measured over 100 ms. The total peak current is the peak value of all the currents. 2: The peak output current is the peak current flowing in each port. 3: The average output current is an average value measured over 100 ms. 51 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Table 14 Recommended operating conditions (Mask ROM version) (VCC = 2.2 to 5.5 V, Ta = -20 to 85C, unless otherwise noted) Symbol f(CNTR 0) f(CNTR 1) Parameter Input frequency for timers X and Y (duty cycle 50%) f(XIN ) Main clock input oscillation frequency (Note 1) f(XCIN ) Sub-clock input oscillation frequency (Notes 1, 2) Test conditions Min. Limits Typ. (4.0 V VCC 5.5 V) Max. 4.0 Unit MHz (10VCC -4)/9 MHz (2.2 V VCC 4.0 V) High-speed mode (4.0 V VCC 5.5 V) High-speed mode (2.2 V VCC 4.0 V) Middle-speed mode 8.0 MHz (20VCC -8)/9 MHz 8.0 MHz 32.768 50 kHz Notes1: When the oscillation frequency has a duty cycle of 50%. 2: When using the microcomputer in low-speed mode, make sure that the sub-clock input oscillation frequency on condition that f(XCIN ) < f(XIN )/3. Table 15 Recommended operating conditions (PROM version) (V CC = 2.5 to 5.5 V, Ta = -20 to 85C, unless otherwise noted) Symbol f(CNTR 0) f(CNTR 1) Parameter Input frequency for timers X and Y (duty cycle 50%) f(XIN ) Main clock input oscillation frequency (Note 1) f(XCIN ) Sub-clock input oscillation frequency (Notes 1, 2) Test conditions (4.0 V VCC 5.5 V) (2.5 V VCC 4.0 V) High-speed mode (4.0 V VCC 5.5 V) High-speed mode (2.5 V VCC 4.0 V) Middle-speed mode Min. Limits Typ. Max. 4.0 Unit MHz (2VCC) -4 MHz 8.0 MHz (4VCC) -8 MHz 8.0 MHz 32.768 50 kHz Notes1: When the oscillation frequency has a duty cycle of 50%. 2: When using the microcomputer in low-speed mode, make sure that the sub-clock input oscillation frequency on condition that f(XCIN ) < f(XIN )/3. 52 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Table 16 Electrical characteristics (VCC =4.0 to 5.5 V, Ta = -20 to 85C, unless otherwise noted) Symbol Parameter VOH "H" output voltage P00-P07, P10-P15 , P30-P37 VOH "H" output voltage P16, P17, P20 -P27, P41-P47 , P50-P57, P60-P67 (Note 1) VOL VOL VOL VT+ - VT- VT+ - VT- VT+ - VT- I IH "L" output voltage P00-P07, P10-P15 , P30-P37 "L" output voltage P16, P17, P20 -P27, P41-P47 , P50-P57, P60-P67 "L" output voltage P40, P71-P77 IOH = -1 mA IOH = -0.25 mA VCC = 2.2 V IOH = -5 mA IOH = -1.5 mA IOH = -1.25 mA VCC = 2.2 V IOL = 5 mA IOL = 1.5 mA IOL = 1.25 mA VCC = 2.2 V IOL = 10 mA IOL = 3.0 mA IOL = 2.5 mA VCC = 2.2 V I OL = 10 mA I OL = 5 mA VCC = 2.2 V Limits Min. VCC-2.0 "H" input current "H" input current I IL "L" input current P00 -P07, P10-P17, P2 0-P27,P4 0-P47, P50 -P57, P60-P67, P7 0-P77 RESET XIN I IL I IL I IL "L" input current "L" input current "L" input current P70 RESET XIN I LOAD Output load current P30-P37 Output leak current P30-P37 VI = VCC VI = VCC VI = VSS Pull-ups "off" VCC = 5 V, VI = VSS Pull-ups "on" VCC = 2.2 V, VI = VSS Pull-ups "on" VI = VSS VI = VSS VCC = 5.0 V, VO = VCC, Pull-ups "on" Output transistors "off" VCC = 2.2 V, VO = VCC, Pull-ups "on" Output transistors "off" VO = VCC, Pull-ups "off" Output transistors "off" VO = VSS, Pull-ups "off" Output transistors "off" Typ. Max. Unit V VCC-0.8 V VCC-2.0 VCC-0.5 V V VCC-0.8 V Hysteresis INT0-INT 2, ADT, CNTR0, CNTR1, P20-P27 Hysteresis SCLK, RXD Hysteresis RESET "H" input current P00-P07, P10-P17 , P20-P27, P40 -P47, VI = VCC P50-P57, P60-P67 , P70-P77 I IH I IH I LEAK Test conditions 2.0 0.5 V V 0.8 V 2.0 0.5 V V 0.8 V 0.5 V 0.3 V 0.5 V 0.5 0.5 V V 5.0 A 5.0 A A -5.0 A 4.0 -60.0 -120.0 -240.0 A -5.0 -20.0 -40.0 A -5.0 -5.0 A A A -4.0 -60.0 -120.0 -240.0 A -5.0 -20.0 -40.0 A 5.0 A -5.0 A 53 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Table 17 Electrical characteristics (VCC =2.2 to 5.5 V, Ta = -20 to 85C, unless otherwise noted) Symbol VRAM Parameter RAM retention voltage Test conditions Min. 2.0 At clock stop mode * High-speed mode, VCC = 5 V Limits Typ. Max. 5.5 Unit V f(XIN) = 8 MHz f(XCIN) = 32.768 kHz Output transistors "off" A-D conver ter in operating * High-speed mode, VCC = 5 V 6.4 13 mA 1.6 3.2 mA 35 70 A 20 40 A 15.0 22.0 A 4.5 9.0 A 0.1 1.0 f(XIN) = 8 MHz (in WIT state) f(XCIN) = 32.768 kHz Output transistors "off" A-D conver ter in operating * Low-speed mode, VCC = 5 V, Ta 55C f(XIN) = stopped I CC Power source current f(XCIN) = 32.768 kHz Output transistors "off" * Low-speed mode, VCC = 5 V, Ta = 25C f(XIN) = stopped f(XCIN) = 32.768 kHz (in WIT state) Output transistors "off" * Low-speed mode, VCC = 3 V, Ta 55C f(XIN) = stopped f(XCIN) = 32.768 kHz Output transistors "off" * Low-speed mode, VCC = 3 V, Ta 25C f(XIN) = stopped f(XCIN) = 32.768 kHz (in WIT state) Output transistors "off" All oscillation stopped (in STP state) Output transistors "off" VL1 Power source voltage I L1 Power source current (V L1) (Note) When using voltage multiplier VL1 = 1.8 V VL1 < 1.3 V Note: When the voltage multiplier control bit of the LCD mode register (bit 4 at address 003916) is "1". 54 Ta = 25 C Ta = 85 C A 10.0 1.3 1.8 3.0 10.0 2.3 6.0 50.0 V A MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Table 18 A-D converter characteristics (VCC = 2.2 to 5.5 V, VSS = 0 V, Ta = -20 to 85C, 4 MHz f(XIN) 8 MHz, in middle/high-speed mode unless otherwise noted) Symbol - Parameter Test conditions Resolution Absolute accuracy (excluding quantization error) VCC VREF = 4 V VCC VREF = 2.7 V t CONV Conversion time f(XIN) = 4 MHz RLADDER I VREF IIA Ladder resistor Reference power source input current Analog port input current VREF = 5 V - Min. Limits Typ. 10 2.5 4.0 31 (Note) 30.5 50 Max. 35 150 0.5 200 5.0 Unit Bits LSB LSB s k A A Note: When an internal trigger is used in middle-speed mode, it is 34 s. Table 19 D-A converter characteristics (VCC = 2.2 to 5.5 V, VCC = VREF, VSS = AVSS = 0 V, Ta = -20 to 85C, in middle/high-speed mode unless otherwise noted) Symbol - - t su RO I VREF Parameter Test conditions Min. Limits Typ. Resolution Absolute accuracy Setting time Output resistor Reference power source input current VCC = VREF = 5 V VCC = VREF = 2.7 V 1 (Note) 3 2.5 Max. 8 1.0 2.0 4 6.0 Unit Bits % % s k mA Note: Using one D-A converter, with the value in the D-A conversion register of the other D-A converter being "00 16", and excluding currents flowing through the A-D resistance ladder. 55 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Table 20 Timing requirements 1 (V CC = 4.0 to 5.5 V, VSS = 0 V, Ta = -20 to 85C, unless otherwise noted) Symbol t w(RESET) t c(X IN) t wH(XIN) t wL(XIN) t c(CNTR) t wH(CNTR) t wL(CNTR) t wH(INT) t wL(INT) t c(S CLK1) t wH(SCLK1) t wL(SCLK1) t su(RXD-SCLK1) t h(SCLK1 -RX D) t c(S CLK2) t wH(SCLK2) t wL (SCLK2 ) t su(SIN2-SCLK2) t h(SCLK2 -SIN2) Parameter Reset input "L" pulse width Main clock input cycle time (X IN input) Main clock input "H" pulse width Main clock input "L" pulse width CNTR0, CNTR1 input cycle time CNTR0, CNTR1 input "H" pulse width CNTR0, CNTR1 input "L" pulse width INT0 to INT2 input "H" pulse width INT0 to INT2 input "L" pulse width Serial I/O1 clock input cycle time (Note) Serial I/O1 clock input "H" pulse width (Note) Serial I/O1 clock input "L" pulse width (Note) Serial I/O1 input set up time Serial I/O1 input hold time Serial I/O2 clock input cycle time (Note) Serial I/O2 clock input "H" pulse width (Note) Serial I/O2 clock input "L" pulse width (Note) Serial I/O2 input set up time Serial I/O2 input hold time Min. 2 125 45 40 250 105 105 80 80 800 370 370 220 100 1000 400 400 200 200 Limits Typ. Max. Unit s ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns Note: When bit 6 of address 001A 16 is "1". Divide this value by four when bit 6 of address 001A 16 is "0". Table 21 Timing requirements 2 (VCC = 2.2 to 4.0 V, VSS = 0 V, Ta = -20 to 85C, unless otherwise noted) Symbol t w(RESET) t c(XIN) t wH(XIN) t wL(XIN) t c(CNTR) t wH(CNTR) t wL(CNTR) t wH(INT) t wL(INT) t c(SCLK1 ) t wH(SCLK1 ) t wL(SCLK1) t su(RXD-SCLK1) t h(SCLK1 -RX D) t c(S CLK2) t wH(SCLK2) t wL(SCLK2) tsu(S IN2-S CLK2) t h(SCLK2 -SIN2 ) Parameter Reset input "L" pulse width Main clock input cycle time (X IN input) Main clock input "H" pulse width Main clock input "L" pulse width CNTR0, CNTR1 input cycle time CNTR0, CNTR1 input "H" pulse width CNTR0, CNTR1 input "L" pulse width INT0 to INT2 input "H" pulse width INT0 to INT2 input "L" pulse width Serial I/O1 clock input cycle time (Note) Serial I/O1 clock input "H" pulse width (Note) Serial I/O1 clock input "L" pulse width (Note) Serial I/O1 input set up time Serial I/O1 input hold time Serial I/O2 clock input cycle time (Note) Serial I/O2 clock input "H" pulse width (Note) Serial I/O2 clock input "L" pulse width (Note) Serial I/O2 input set up time Serial I/O2 input hold time Note: When bit 6 of address 001A 16 is "1". Divide this value by four when bit 6 of address 001A 16 is "0". 56 Limits Min. Typ. 2 125 45 40 900/(V CC-0.4) t c(CNTR)/2-20 t c(CNTR)/2-20 230 230 2000 950 950 400 200 2000 950 950 400 300 Max. Unit s ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Table 22 Switching characteristics 1 (VCC = 4.0 to 5.5 V, VSS = 0 V, Ta = -20 to 85C, unless otherwise noted) Symbol t wH(SCLK1) t wL(SCLK1) t d(SCLK1 -TX D) t v(S CLK1-TX D) t r(SCLK1 ) t f(SCLK1) t wH(SCLK2) t wL(SCLK2) t d(SCLK2-SOUT2 ) t v(SCLK2-S OUT2) t f(SCLK2) t r(CMOS) t f(CMOS) Parameter Serial I/O1 clock output "H" pulse width Serial I/O1 clock output "L" pulse width Serial I/O1 output delay time (Note 1) Serial I/O1 output valid time (Note 1) Serial I/O1 clock output rising time Serial I/O1 clock output falling time Serial I/O2 clock output "H" pulse width Serial I/O2 clock output "L" pulse width Serial I/O2 output delay time Serial I/O2 output valid time Serial I/O2 clock output falling time CMOS output rising time (Note 2) CMOS output falling time (Note 2) Limits Min. tC (S CLK1)/2-30 tC (S CLK1)/2-30 Typ. Max. 140 -30 30 30 tC (SCLK2)/2-160 tC (SCLK2)/2-160 0.2 tC (S CLK2) 0 10 10 40 30 30 Unit ns ns ns ns ns ns ns ns ns ns ns ns ns Notes1: When the P45/TX D P-channel output disable bit of the UART control register (bit 4 of address 001B16) is "0". 2: XOUT and X COUT pins are excluded. Table 23 Switching characteristics 2 (VCC = 2.2 to 4.0 V, VSS = 0 V, Ta = -20 to 85C, unless otherwise noted) Symbol t wH(SCLK1) twL(S CLK1) t d(SCLK1 -TX D) t v(S CLK1-TX D) t r(SCLK1 ) t f(SCLK1) t wH(SCLK2) t wL(SCLK2) t d(SCLK2-SOUT2 ) t v(SCLK2-S OUT2) t f(SCLK2) t r(CMOS) t f(CMOS) Parameter Serial I/O1 clock output "H" pulse width Serial I/O1 clock output "L" pulse width Serial I/O1 output delay time (Note 1) Serial I/O1 output valid time (Note 1) Serial I/O1 clock output rising time Serial I/O1 clock output falling time Serial I/O2 clock output "H" pulse width Serial I/O2 clock output "L" pulse width Serial I/O2 output delay time Serial I/O2 output valid time Serial I/O2 clock output falling time CMOS output rising time (Note 2) CMOS output falling time (Note 2) Min. tC (S CLK1)/2-50 tC (S CLK1)/2-50 Limits Typ. Max. 350 -30 50 50 tC (SCLK2)/2-240 tC (SCLK2)/2-240 0.2 tC (S CLK2) 0 20 20 50 50 50 Unit ns ns ns ns ns ns ns ns ns ns ns ns ns Notes1: When the P45/TX D P-channel output disable bit of the UART control register (bit 4 of address 001B16) is "0". 2: XOUT and X COUT pins are excluded. 57 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER Measurement output pin 1 k 100 pF Measurement output pin CMOS output 100 pF N-channel open-drain output (Note) Note : When bit 4 of the UART control register (address 001B 16) is "1". (N-channel open-drain output mode) Fig. 56 Circuit for measuring output switching characteristics 58 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER tC (CNTR) tWL (CNTR) tWH (CNTR) CNTR0, CNTR1 0.8VCC INT0-INT3 0.8VCC 0.2VCC tWL (INT) tWH (INT) 0.2VCC tW (RESET) RESET 0.8VCC 0.2VCC tC (XIN) tWL (XIN) tWH (XIN) 0.8VCC XIN tC (SCLK) tr tf SCLK 0.2VCC tWL (SCLK) tWH (SCLK) 0.8VCC 0.2VCC tsu (RXD-SCLK) th (SCLK-RXD) 0.8VCC 0.2VCC RX D td (SCLK-TXD) tv (SCLK-TXD) TXD Fig. 57 Timing diagram 59 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER MASK ROM ORDER CONFIRMATION FORM GZZ-SH52-92B<85A0> 740 FAMILY MASK ROM CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M38277M8MXXXFP/GP/HP MITSUBISHI ELECTRIC Receipt Mask ROM number Date: Section head Supervisor signature signature Customer TEL ( Company name Date issued ) Date: Issuance signature Note : Please fill in all items marked . Submitted by Supervisor 1. Confirmation Specify the name of the product being ordered and the type of EPROMs submitted. Three EPROMs are required for each pattern. If at least two of the three sets of EPROMs submitted contain identical data, we will produce masks based on this data. We shall assume the responsibility for errors only if the mask ROM data on the products we produce differs from this data. Thus, extreme care must be taken to verify the data in the submitted EPROMs. Product name: M38277M8MXXXFP M38277M8MXXXGP Checksum code for entire EPROM M38277M8MXXXHP (hexadecimal notation) EPROM type (indicate the type used) 27512 EPROM address 000016 000F16 001016 Product name ASCII code : `M38277M8M' In the address space of the microcomputer, the internal ROM area is from address 808016 to FFFD 16. The reset vector is stored in addresses FFFC16 and FFFD16. 807F 16 808016 Data ROM 32K-130 bytes FFFD 16 FFFE 16 FFFF16 (1) Set the data in the unused area (the shaded area of the diagram) to "FF16". (2) The ASCII codes of the product name "M38277M8M" must be entered in addresses 000016 to 000816 . And set data "FF16 " in addresses 000916 to 000F 16. The ASCII codes and addresses are listed to the right in hesadecimal notation. (1/2) 60 Address 000016 000116 000216 000316 000416 000516 000616 000716 `M' = 4D16 `3' = 3316 `8' = 3816 `2' = 3216 `7' = 3716 `7' = 3716 `M' = 4D16 `8' = 3816 Address 000816 000916 000A16 000B16 000C16 000D16 000E16 000F16 ` M ' =4D16 FF16 FF16 FF16 FF16 FF16 FF16 FF16 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER GZZ-SH52-92B<85A0> Mask ROM number 740 FAMILY MASK ROM CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M38277M8MXXXFP/GP/HP MITSUBISHI ELECTRIC We recommend the use of the following pseudo-command to set the start address of the assembier source program because ASCII codes of the product name are written to addresses 000016 to 000816 of EPROM. EPROM type 27512 The pseudo-command *=$0000 .BYTE `M38277M8M' Note: If the name of the product written to the EPROMs does not match the name of the mask ROM confirmation form, the ROM will not be processed. 2. Mark specification Mark specification must be submitted using the correct form for the package being ordered. Fill out the appropriate mark specification form (100P6S for M38277M8MXXXFP, 100P6Q for M38277M8MXXXGP, 100PFB for M38277M8MXXXHP) and attach it to the mask ROM confirmation form. 3. Usage conditions Please answer the following questions about usage for use in our product inspection : (1) How will you use the XIN-XOUT oscillator? Ceramic resonator Quartz crystal External clock input At what frequency? Other ( ) f(XIN) = MHz (2) How will you use the XCIN-XCOUT oscillator? Ceramic resonator Other ( At what frequency? Quartz crystal ) f(XCIN) = MHz 4. Comments (2/2) 61 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER ROM PROGRAMMING CONFIRMATION FORM GZZ-SH51-93B<85A0> ROM number SINGLE-CHIP MICROCOMPUTER M38279EF-XXXFP/GP/HP MITSUBISHI ELECTRIC Receipt 740 FAMILY ROM PROGRAMMING CONFIRMATION FORM Date: Section head Supervisor signature signature Customer TEL ( Company name Date issued ) Date: Issuance signature Note : Please fill in all items marked . Submitted by Supervisor 1. Confirmation Specify the name of the product being ordered and the type of EPROMs submitted. Three EPROMs are required for each pattern. If at least two of the three sets of EPROMs submitted contain identical data, we will produce ROM programming based on this data. We shall assume the responsibility for errors only if the programming data on the products we produce differs from this data. Thus, extreme care must be taken to verify the data in the submitted EPROMs. Product name: M38279EF-XXXFP M38279EF-XXXGP Checksum code for entire EPROM M38279EF-XXXHP (hexadecimal notation) EPROM type (indicate the type used) 27512 EPROM address 000016 000F16 001016 107F 16 108016 Product name ASCII code : `M38279EF-' In the address space of the microcomputer, the internal ROM area is from address 108016 to FFFD 16. The reset vector is stored in addresses FFFC16 and FFFD16 . Data ROM 60K-130 bytes FFFD16 FFFE16 FFFF16 (1) Set the data in the unused area (the shaded area of the diagram) to "FF16". (2) The ASCII codes of the product name "M38279EF-" must be entered in addresses 0000 16 to 0008 16. And set data "FF16 " in addresses 000916 to 000F16. The ASCII codes and addresses are listed to the right in hesadecimal notation. (1/2) 62 Address 000016 000116 000216 000316 000416 000516 000616 000716 `M' = 4D16 `3' = 3316 `8' = 3816 `2' = 3216 `7' = 3716 `9' = 3916 `E' = 4516 `F' = 4616 Address 000816 000916 000A16 000B16 000C16 000D16 000E16 000F16 ` - ' =2D16 FF16 FF16 FF16 FF16 FF16 FF16 FF16 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER GZZ-SH51-93B<85A0> ROM number 740 FAMILY ROM PROGRAMMING CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M38279EF-XXXFP/GP/HP MITSUBISHI ELECTRIC We recommend the use of the following pseudo-command to set the start address of the assembier source program because ASCII codes of the product name are written to addresses 0000 16 to 000816 of EPROM. EPROM type 27512 The pseudo-command *=$0000 .BYTE `M38279EF-' Note: If the name of the product written to the EPROMs does not match the name of the ROM programming confirmation form, the ROM will not be processed. 2. Mark specification Mark specification must be submitted using the correct form for the package being ordered. Fill out the appropriate mark specification form (100P6S for M38279EF-XXXFP, 100P6Q for M38279EF-XXXGP, 100PFB for M38279EF-XXXHP) and attach it to the ROM programming confirmation form. 3. Usage conditions Please answer the following questions about usage for use in our product inspection : (1) How will you use the XIN-XOUT oscillator? Ceramic resonator Quartz crystal External clock input At what frequency? Other ( ) f(XIN) = MHz (2) How will you use the XCIN-XCOUT oscillator? Ceramic resonator Other ( At what frequency? Quartz crystal ) f(XCIN) = MHz 4. Comments (2/2) 63 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER 100P6S-A Plastic 100pin 1420mm body QFP EIAJ Package Code QFP100-P-1420-0.65 Weight(g) 1.58 Lead Material Alloy 42 MD e JEDEC Code - 100 ME HD D b2 81 1 80 I2 E HE Recommended Mount Pad 30 Symbol A A1 A2 b c D E e HD HE L L1 y 51 31 50 A c A2 L1 F b A1 e b2 I2 MD ME L Detail F y 100P6Q-A Dimension in Millimeters Min Nom Max - - 3.05 0.1 0.2 0 2.8 - - 0.25 0.3 0.4 0.13 0.15 0.2 13.8 14.0 14.2 19.8 20.0 20.2 0.65 - - 16.5 16.8 17.1 22.5 22.8 23.1 0.4 0.6 0.8 1.4 - - 0.1 - - 0 10 - 0.35 - - - - 1.3 - - 14.6 - - 20.6 Plastic 100pin 1414mm body LQFP EIAJ Package Code LQFP100-P-1414-0.50 Weight(g) Lead Material Cu Alloy MD e JEDEC Code - b2 ME HD D 76 100 I2 75 1 Symbol HE E Recommended Mount Pad 51 25 50 26 A L1 F b y A1 c A2 e L Detail F 64 A A1 A2 b c D E e HD HE L L1 y b2 I2 MD ME Dimension in Millimeters Min Nom Max - - 1.7 0.1 0.2 0 1.4 - - 0.13 0.18 0.28 0.105 0.125 0.175 13.9 14.0 14.1 13.9 14.0 14.1 0.5 - - 15.8 16.0 16.2 15.8 16.0 16.2 0.3 0.5 0.7 1.0 - - 0.1 - - 0 10 - 0.225 - - - - 1.0 - - 14.4 - - 14.4 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER 100PFB-A Plastic 100pin 1212mm body TQFP EIAJ Package Code TQFP100-P-1212-0.40 Weight(g) Lead Material Cu Alloy MD e JEDEC Code - HD Under Development ME D 76 b2 100 1 75 l2 25 HE E Recommended Mount Pad Symbol A A1 A2 b c D E e HD HE L L1 y 51 26 50 A L1 e A1 c A2 F y b b2 I2 MD ME L Detail F 100D0 Dimension in Millimeters Min Nom Max - - 1.2 0.1 0.15 0.05 1.0 - - 0.13 0.18 0.23 0.105 0.125 0.175 11.9 12.0 12.1 11.9 12.0 12.1 0.4 - - 13.8 14.0 14.2 13.8 14.0 14.2 0.4 0.5 0.6 1.0 - - 0.08 - - 0 8 - 0.225 - - 1.0 - - 12.4 - - - - 12.4 Glass seal 100pin QFN EIAJ Package Code - JEDEC Code - Weight(g) 18.850.15 5.0MAX 21.00.13 3.5TYP 0.65TYP 0.45TYP 80 51 81 INDEX 0.35TYP 0.65TYP 12.350.15 1.075TYP 15.60.13 0.65TYP 50 31 100 30 1.075TYP 1 65 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER 100P6S (100-PIN QFP) MARK SPECIFICATION FORM Mitsubishi IC catalog name Please choose one of the marking types below (A, B, C), and enter the Mitsubishi catalog name and the special mark (if needed). A. Standard Mitsubishi Mark 80 51 81 50 Mitsubishi IC catalog name Mitsubishi lot number (6-digit or 7-digit) 31 100 1 30 B. Customer's Parts Number + Mitsubishi catalog name 80 51 81 50 31 100 1 30 Customer's Parts Number Note : The fonts and size of characters are standard Mitsubishi type. Mitsubishi IC catalog name Note1 : The mark field should be written right aligned. 2 : The fonts and size of characters are standard Mitsubishi type. 3 : Customer's Parts Number can be up to 14 characters : Only 0 ~ 9, A ~ Z, +, -, /, (, ), &, , (periods), (commas) are usable. 4 : If the Mitsubishi logo is not required, check the box below. Mitsubishi logo is not required . , C. Special Mark Required 80 51 81 50 100 31 1 Note1 : If the Special Mark is to be Printed, indicate the desired layout of the mark in the left figure. The layout will be duplicated as close as possible. Mitsubishi lot number (6-digit or 7-digit) and Mask ROM number (3-digit) are always marked. 2 : If the customer's trade mark logo must be used in the Special Mark, check the box below. Please submit a clean original of the logo. For the new special character fonts a clean font original (ideally logo drawing) must be submitted. 30 Special logo required 66 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER 100P6Q (100-PIN LQFP) MARK SPECIFICATION FORM Mitsubishi IC catalog name Please choose one of the marking types below (A, B, C), and enter the Mitsubishi catalog name and the special mark (if needed). A. Standard Mitsubishi Mark 75 51 76 50 Mitsubishi IC catalog name Mitsubishi IC catalog name Mitsubishi lot number (6-digit or 7-digit) 100 26 1 25 B. Customer's Parts Number + Mitsubishi catalog name 75 51 76 50 Mitsubishi lot number (6-digit or 7-digit) 100 26 1 25 Customer's Parts Number Note : The fonts and size of characters are standard Mitsubishi type. Mitsubishi IC catalog name Note1 : The mark field should be written right aligned. 2 : The fonts and size of characters are standard Mitsubishi type. 3 : Customer's Parts Number can be up to 12 characters : Only 0 ~ 9, A ~ Z, +, -, /, (, ), &, , (periods), (commas) are usable. 4 : If the Mitsubishi logo is not required, check the box below. Mitsubishi logo is not required . , C. Special Mark Required 75 51 76 50 100 26 Note1 : If the Special Mark is to be Printed, indicate the desired layout of the mark in the left figure. The layout will be duplicated as close as possible. Mitsubishi lot number (6-digit or 7-digit) and Mask ROM number (3-digit) are always marked. 2 : If the customer's trade mark logo must be used in the Special Mark, check the box below. Please submit a clean original of the logo. For the new special character fonts a clean font original (ideally logo drawing) must be submitted. Special logo required 1 25 67 MITSUBISHI MICROCOMPUTERS 3827 Group SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER 100PFB (100-PIN TQFP) MARK SPECIFICATION FORM Mitsubishi IC catalog name Please choose one of the marking types below (A, B, C), and enter the Mitsubishi catalog name and the special mark (if needed). A. Standard Mitsubishi Mark 75 51 50 76 Mitsubishi IC catalog name Mitsubishi IC catalog name Mitsubishi lot number (6-digit or 7-digit) 100 26 1 25 B. Customer's Parts Number + Mitsubishi catalog name 75 51 50 76 Mitsubishi lot number (6-digit or 7-digit) 100 26 1 Customer's Parts Number Note : The fonts and size of characters are standard Mitsubishi type. Mitsubishi IC catalog name Note1 : The mark field should be written right aligned. 2 : The fonts and size of characters are standard Mitsubishi type. 3 : Customer's Parts Number can be up to 10 characters : Only 0 ~ 9, A ~ Z, +, -, /, (, ), &, , (periods), (commas) are usable. 4 : If the Mitsubishi logo is not required, check the box below. Mitsubishi logo is not required . , 25 5 : The allocation of Mitsubishi IC catalog name and Mitsubishi Product number depend on the Mitsubishi IC catalog name's characters, and requiring Mitsubishi logo or not. C. Special Mark Required 75 51 76 50 100 26 Note1 : If the Special Mark is to be Printed, indicate the desired layout of the mark in the left figure. The layout will be duplicated as close as possible. Mitsubishi lot number (6-digit or 7-digit) and Mask ROM number (3-digit) are always marked. 2 : If the customer's trade mark logo must be used in the Special Mark, check the box below. Please submit a clean original of the logo. For the new special character fonts a clean font original (ideally logo drawing) must be submitted. Special logo required 1 68 25 Keep safety first in your circuit designs! * Mitsubishi Electric Corporation puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of non-flammable material or (iii) prevention against any malfunction or mishap. * These materials are intended as a reference to assist our customers in the selection of the Mitsubishi semiconductor product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Mitsubishi Electric Corporation or a third party. Mitsubishi Electric Corporation assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data, diagrams, charts or circuit application examples contained in these materials. All information contained in these materials, including product data, diagrams and charts, represent information on products at the time of publication of these materials, and are subject to change by Mitsubishi Electric Corporation without notice due to product improvements or other reasons. It is therefore recommended that customers contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor for the latest product information before purchasing a product listed herein. Mitsubishi Electric Corporation semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. The prior written approval of Mitsubishi Electric Corporation is necessary to reprint or reproduce in whole or in part these materials. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. Please contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor for further details on these materials or the products contained therein. Notes regarding these materials * * * * * * (c) 1998 MITSUBISHI ELECTRIC CORP. New publication, effective Jun. 1998. Specifications subject to change without notice. REVISION DESCRIPTION LIST Rev. No. 1.0 3827 GROUP DATA SHEET Revision Description First Edition Rev. date 980602 (1/1)