LM193, LM293, LM293A, LM393 LM393A, LM2903, LM2903Q DUAL DIFFERENTIAL COMPARATORS SLCS005K - JUNE 1976 - REVISED JUNE 2002 D D D D D D D D LM193 . . . D OR JG PACKAGE LM293 . . . D OR P PACKAGE LM293A . . . D PACKAGE LM393, LM393A . . . D, P, PS, OR PW PACKAGE LM2903 . . . D, P, PS, OR PW PACKAGE LM2903Q . . . D OR P PACKAGE (TOP VIEW) 1OUT 1IN- 1IN+ GND 1 8 2 7 3 6 4 5 VCC 2OUT 2IN- 2IN+ LM193 . . . FK PACKAGE (TOP VIEW) NC 1OUT NC VCC NC D Single Supply or Dual Supplies Wide Range of Supply Voltage . . . 2 V to 36 V Low Supply-Current Drain Independent of Supply Voltage . . . 0.4 mA Typ Per Comparator Low Input Bias Current . . . 25 nA Typ Low Input Offset Current . . . 3 nA Typ (LM193) Low Input Offset Voltage . . . 2 mV Typ Common-Mode Input Voltage Range Includes Ground Differential Input Voltage Range Equal to Maximum-Rated Supply Voltage . . . 36 V Low Output Saturation Voltage Output Compatible With TTL, MOS, and CMOS LM2903Q Available in Q-Temp Automotive - High-Reliability Automotive Applications - Configuration Control/Print Support - Qualification to Automotive Standards NC 1IN- NC 1IN+ NC 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 NC 2OUT NC 2IN- NC NC GND NC 2IN+ NC D D description These devices consist of two independent voltage NC - No internal connection comparators that are designed to operate from a single power supply over a wide range of voltages. Operation from dual supplies also is possible as long as the difference between the two supplies is 2 V to 36 V, and VCC is at least 1.5 V more positive than the input common-mode voltage. Current drain is independent of the supply voltage. The outputs can be connected to other open-collector outputs to achieve wired-AND relationships. The LM193 is characterized for operation from -55C to 125C. The LM293 and LM293A are characterized for operation from -25C to 85C. The LM393 and LM393A are characterized for operation from 0C to 70C. The LM2903 is characterized for operation from -40C to 125C. The LM2903Q is tested from -40C to 125C and is manufactured to demanding automotive requirements. symbol (each comparator) IN+ IN- OUT Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2002, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. On all other products, production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 LM193, LM293, LM293A, LM393 LM393A, LM2903, LM2903Q DUAL DIFFERENTIAL COMPARATORS SLCS005K - JUNE 1976 - REVISED JUNE 2002 AVAILABLE OPTIONS PACKAGE VIO(max) AT 25C TA CERAMIC DIP (JG) LM393D -- -- LM393PS -- -- LM393AD -- -- LM393APS -- -- 5 mV LM293D -- -- 2 mV LM293AD -- -- LM2903D -- -- LM2903PS -- -- -- -- -- -- LM2903QP -- LM193FK LM193JG -- -- 0C to 70C 2 mV -25C 25C to 85C -40C to 125C 7 mV -55C to 125C 5 mV LM2903QD LM193D PLASTIC DIP (P) PLASTIC THIN SHRINK SMALL OUTLINE (PW) CHIP CARRIER (FK) 5 mV SMALL OUTLINE (D, PS) LM393P LM393PW -- -- LM393AP -- LM393APW -- LM293P -- -- -- LM2903P LM2903PW The D package also is available taped and reeled. Add the suffix R (e.g., LM393DR). The PS and PW packages are only available taped and reeled. schematic (each comparator) VCC 80-A Current Regulator 10 A 60 A 10 A IN+ 80 A COMPONENT COUNT OUT IN- GND Current values shown are nominal. 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 Epi-FET Diodes Resistors Transistors 1 2 2 30 LM193, LM293, LM293A, LM393 LM393A, LM2903, LM2903Q DUAL DIFFERENTIAL COMPARATORS SLCS005K - JUNE 1976 - REVISED JUNE 2002 absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 V Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 V Input voltage range, VI (either input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to 36 V Output voltage, VO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 V Output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA Duration of output short-circuit to ground (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unlimited Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Package thermal impedance, JA (see Note 4): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97C/W P package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85C/W PS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149C/W Case temperature for 60 seconds: FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D, P, PS, or PW package . . . . . . . . 260C Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: JG package . . . . . . . . . . . . . . . . . . . . 300C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65C to 150C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values, except differential voltages, are with respect to GND. 2. Differential voltages are at IN+ with respect to IN-. 3. Short circuits from outputs to VCC can cause excessive heating and eventual destruction. 4. The package thermal impedance is calculated in accordance with JESD 51-7. DISSIPATION RATING TABLE PACKAGE TA 25C POWER RATING DERATING FACTOR DERATE ABOVE TA TA = 70C POWER RATING TA = 85C POWER RATING TA = 125C POWER RATING FK 900 mW 11.0 mW/C 68C 880 mW 715 mW 275 mW JG 900 mW 8.4 mW/C 43C 672 mW 546 mW 210 mW POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 3 LM193, LM293, LM293A, LM393 LM393A, LM2903, LM2903Q DUAL DIFFERENTIAL COMPARATORS SLCS005K - JUNE 1976 - REVISED JUNE 2002 electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted) PARAMETER MIN VCC = 5 V to 30 V, VO = 1 1.4 4V V, VIC = VIC(min) VIO Input offset voltage IIO Input offset current VO = 1 1.4 4V IIB Input bias current 4V VO = 1 1.4 AVD Large-signal differential-voltage amplification IOH High-level g output current VOL 25C TYP MAX 2 5 UNIT TYP MAX 2 5 9 25C 3 9 25 5 100 25C -25 Full range VCC = 15 V, VO = 1.4 V to 11.4 V, RL 15 k to VCC VOH = 5 V, VID = 1 V MIN mV Full range Full range Common-mode VICR input voltage range LM293 LM393 LM193 TA TEST CONDITIONS -100 -25 -300 0 to VCC-1.5 0 to VCC-1.5 Full range 0 to VCC-2 0 to VCC-2 25C 50 25C VOH = 30 V, VID = 1 V Low-level output voltage IOL = 4 mA mA, VID = -1 1V IOL Low-level output current VOL = 1.5 V, VID = -1 V 25C ICC Supply current RL = VCC = 5 V VCC = 30 V 25C 50 0.1 Full range 25C 150 200 0.1 400 150 700 6 Full range 1 2.5 nA V/mV 50 nA 1 A 400 700 6 0.8 nA V 1 Full range -250 -400 25C 200 50 250 mV mA 0.8 1 2.5 mA Full range (MIN or MAX) for LM193 is -55C to 125C, for LM293 is 25C to 85C, and for LM393 is 0C to 70C. All characteristics are measured with zero common-mode input voltage, unless otherwise specified. The voltage at either input or common-mode should not be allowed to go negative by more than 0.3 V. The upper end of the common-mode voltage range is VCC+ - 1.5 V, but either or both inputs can go to 30 V without damage. 4 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 LM193, LM293, LM293A, LM393 LM393A, LM2903, LM2903Q DUAL DIFFERENTIAL COMPARATORS SLCS005K - JUNE 1976 - REVISED JUNE 2002 electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted) PARAMETER LM293A LM393A TA TEST CONDITIONS MIN VCC = 5 V to 30 V, VO = 1 1.4 4V V, VIC = VIC(min) VIO Input offset voltage IIO Input offset current VO = 1 1.4 4V IIB Input bias current 4V VO = 1 1.4 Large-signal differential-voltage amplification IOH High-level g output current VOL TYP MAX 1 2 25C MIN UNIT TYP MAX 2 7 mV Full range 4 25C 5 Full range 15 50 5 150 25C -25 Full range Common-mode VICR input voltage range AVD LM2903 LM2903Q -250 -25 -400 0 to VCC-1.5 0 to VCC-1.5 Full range 0 to VCC-2 0 to VCC-2 25C 50 25C VOH = 30 V, VID = 1 V Low-level output voltage IOL = 4 mA mA, VID = -1 1V IOL Low-level output current VOL = 1.5 V, VID = -1 V 25C ICC Supply current RL = VCC = 5 V VCC = 30 V 25C 200 0.1 Full range 25 50 25C 150 100 0.1 400 150 700 6 Full range 1 nA V/mV 50 nA 1 A 400 700 6 0.8 nA V 1 Full range -250 -500 25C VCC = 15 V, VO = 1.4 V to 11.4 V, RL 15 k to VCC VOH = 5 V, VID = 1 V 50 200 mV mA 0.8 2.5 1 2.5 mA Full range (MIN or MAX) for LM293A is 25C to 85C, for LM393A is 0C to 70C, and for LM2903 and LM2903Q is -40C to 125C. All characteristics are measured with zero common-mode input voltage, unless otherwise specified. The voltage at either input or common-mode should not be allowed to go negative by more than 0.3 V. The upper end of the common-mode voltage range is VCC+ - 1.5 V, but either or both inputs can go to 30 V without damage. switching characteristics, VCC = 5 V, TA = 25C PARAMETER TEST CONDITIONS LM193 LM293, LM293A LM393, LM393A LM2903, LM2903Q UNIT TYP Response time RL connected to 5 V through g 5.1 k, CL = 15 pF, See Note 5 100-mV input step with 5-mV overdrive 1.3 TTL-level input step 0.3 s CL includes probe and jig capacitance. NOTE 5: The response time specified is the interval between the input step function and the instant when the output crosses 1.4 V. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 5 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2002, Texas Instruments Incorporated