LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
DSingle-Supply Operation:
Input Voltage Range Extends to Ground,
and Output Swings to Ground While
Sinking Current
DInput Offset Voltage 300 µV Max at 25°C for
LT1014
DOffset Voltage Temperature Coefficient
2.5 µV/°C Max for LT1014
DInput Offset Current 1.5 nA Max at 25°C for
LT1014
DHigh Gain 1.2 V/µV Min (RL = 2 kΩ), 0.5 V/µV
Min (RL = 600 Ω) for LT1014
DLow Supply Current 2.2 mA Max at 25°C for
LT 1014
DLow Peak-to-Peak Noise Voltage
0.55 µV Typ
DLow Current Noise 0.07 pA/√Hz Typ
description
The LT1014, LT1014A, and LT1014D are quad
precision operational amplifiers with 14-pin
industry-standard configuration. They feature low
offset-voltage temperature coefficient, high gain,
low supply current, and low noise.
The LT1014, LT1014A, and LT1014D can be
operated with both dual ±15-V and single 5-V
power supplies. The common-mode input voltage
range includes ground, and the output voltage can
also swing to within a few milivolts of ground.
Crossover distortion is eliminated.
The LT1014C and LT1014D are characterized for
operation from 0°C to 70°C. The LT1014I and
LT1014DI are characterized for operation from
−40°C to 105°C. The LT1014M, LT1014AM and
LT1014DM are characterized for operation over
the full military temperature range of −55°C to
125°C.
Copyright 2009, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
1OUT
1IN−
1IN+
VCC+
2IN+
2IN−
2OUT
NC
4OUT
4IN−
4IN+
VCC−/GND
3IN+
3IN−
3OUT
NC
DW PACKAGE
(TOP VIEW)
1
2
3
4
5
6
7
14
13
12
11
10
9
8
1OUT
1IN−
1IN+
VCC+
2IN+
2IN−
2OUT
4OUT
4IN−
4IN+
VCC−
3IN+
3IN−
3OUT
3212019
910111213
4
5
6
7
8
18
17
16
15
14
4IN+
NC
VCC−/GND
NC
3IN+
1IN+
NC
VCC+
NC
2IN+
1IN−
1OUT
NC
3IN− 4IN−
2IN−
2OUT
NC
3OUT 4OUT
J OR N PACKAGE
(TOP VIEW)
FK PACKAGE
(TOP VIEW)
NC − No internal connection
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
2POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
AVAILABLE OPTIONS{
PACKAGED DEVICES}
TA
VIO max
AT 25°C
SMALL
OUTLINE
(DW)§
CHIP
CARRIER
(FK)
CERAMIC
DIP
(J)
PLASTIC
DIP
(N)
0°Cto70°C
300
µ
V — — — LT1014CN
0°C to 70°C
300
µV
800 µV LT1014DDW — —
LT1014CN
LT1014DN
40°C to 105°C
300
µ
V — — — LT1014IN
−40°C to 105°C
300
µV
800 µV LT1014DIDW — —
LT1014IN
LT1014DIN
180
µ
V — LT1014AMFK LT1014AMJ —
−55°C to 125°C
180
µV
300 µV
—
—
LT1014AMFK
LT1014MFK
LT1014AMJ
LT1014MJ
—
LT1014MN
55 C
to
125 C
300
µV
800 µV LT1014DMDW
LT1014MFK
—
LT1014MJ
—
LT1014MN
LT1014DMN
†For the most current package and ordering information, see the Package Option Addendum at the end
of this document, or see the TI web site at www.ti.com.
‡Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
§The DW package is available taped and reeled. Add the suffix R to the device type
(e.g., LT1014DDWR).
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
schematic (each amplifier)
VCC+
IN−
IN+
VCC−
Ωk9 Ωk9 Ωk1.6 Ωk1.6 Ωk1.6 Ω100 Ωk1 Ω800
Q5
Q6 Q13 Q16 Q14 Q15 Q32
Q30
Q25
Q35
Q36
Q41
Q39
Ω600
Q3
Q4
Q37
J1
Q33
Q26
Ωk3.9
Q27
Q38
Q28
Q2
Q22
Q1
Q21
Ω400
Ω400
Q12
Q11
Q9
75 pF
Q7
Q29
Q10
Q18
Q19
Q17
21 pF 2.5 pF
Ωk2.4
Ω18
Ωk14
OUT
Q40
Q8
Ωk5 Ωk5
10 pF
Ωk2
Ωk1.3
Q20
4 pF Q31
Q34
Q23
Q24
Ωk2
10 pF
Ωk2
Ω30
Ωk42
Component values are nominal.
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
4POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage (see Note 1): VCC+ 22 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VCC− −22 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Differential input voltage (see Note 2) ±30 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input voltage range, VI (any input) (see Note 1) VCC− − 5 V to VCC+
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Duration of short-circuit current at (or below) TA = 25°C (see Note 3) Unlimited. . . . . . . . . . . . . . . . . . . . . . . . .
Continuous total power dissipation See Dissipation Rating Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating free-air temperature range, TA: LT1014C, LT1014D −0°C to 70°C. . . . . . . . . . . . . . . . . . . . . . . . . . .
LT1014I, LT1014DI −40°C to 105°C. . . . . . . . . . . . . . . . . . . . . . . . . .
LT1014M, LT1014AM, LT1014DM −55°C to 125°C. . . . . . . . . . . . .
Case temperature for 60 seconds: FK package 260°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range, Tstg −65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
†Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between VCC+ and VCC−.
2. Differential voltages are at the noninverting input with respect to the inverting input.
3. The output may be shorted to either supply.
DISSIPATION RATING TABLE
PACKAGE TA ≤ 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 105°C
POWER RATING
TA = 125°C
POWER RATING
DW 1025 mV 8.2 mW/°C656 mW 369 mW 205 mW
FK 1375 mV 11.0 mW/°C 880 mW 495 mW 275 mW
J1375 mV 11.0 mW/°C 880 mW 495 mW 275 mW
N1150 mV 9.2 mW/°C736 mW 414 mW 230 mW
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VCC± = ±15 V, VIC = 0 (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
T†
LT1014C LT1014D
UNIT
PARAMETER TEST CONDITIONS TA†
MIN TYP‡MAX MIN TYP‡MAX UNIT
V
Input offset voltage
R50 Ω
25°C 60 300 200 800
V
VIO Input offset voltage RS = 50 ΩFull range 550 1000 µV
aVIO
Temperature coeficient
of input offset voltage Full range 0.4 2.5 0.7 5 µV/°C
Long-term drift
of input offset voltage 25°C 0.5 0.5 µV/mo
I
Input offset current
25°C 0.15 1.5 0.15 1.5
nA
IIO Input offset current Full range 2.8 2.8 nA
I
Input bias current
25°C −12 −30 −12 −30
nA
IIB Input bias current Full range −38 −38 nA
V
ICR
Common-mode
input voltage range
25°C
−15
to
13.5
−15.3
to
13.8
−15
to
13.5
−15.3
to
13.8 V
VICR
input voltage range
Full range −15
to 13
−15
to 13
V
V
Maximum peak output
R2kΩ
25°C±12.5 ±14 ±12.5 ±14
V
VOM
Maximum
peak
output
voltage swing RL = 2 kΩFull range ±12 ±12 V
L i l diff ti l
VO = ±10 V, RL = 600 Ω25°C 0.5 2 0.5 2
AVD
Large-signal differential
voltage amplification
V±10 V
R2kΩ
25°C 1.2 8 1.2 8 V/µV
AVD
vo
lt
age amp
lifi
ca
ti
on VO = ±10 V, RL = 2 kΩFull range 0.7 0.7
V/µV
CMRR
Common-mode VIC = −15 V to 13.5 V 25°C 97 117 97 117
dB
CMRR
Common mode
rejection ratio VIC = −15 V to 13 V Full range 94 94 dB
k
Supply-voltage
rejection ratio
V±2Vto±18 V
25°C 100 117 100 117
dB
kSVR rejection ratio
(∆VCC/∆VIO)
VCC± = ±2 V to ±18 V
Full range 97 97
dB
Channel separation VO = ±10 V, RL = 2 kΩ25°C 120 137 120 137 dB
rid
Differential
input resistance 25°C 70 300 70 300 MΩ
ric
Common-mode
input resistance 25°C 4 4 GΩ
I
Suppl
y
current 25°C 0.35 0.55 0.35 0.55
mA
ICC
Supply
current
per amplifier Full range 0.6 0.6 mA
†Full range is 0°C to 70°C.
‡All typical values are at TA = 25°C.
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
6POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VCC± = 5 V, VCC− = 0, VO = 1.4 V, VIC = 0
(unless otherwise noted)
PARAMETER
TEST CONDITIONS
T†
LT1014C LT1014D
UNIT
PARAMETER TEST CONDITIONS TA†
MIN TYP MAX MIN TYP MAX UNIT
V
Input offset voltage
R50 Ω
25°C 90 450 250 950
V
VIO Input offset voltage RS = 50 ΩFull range 570 1200 µV
I
Input offset current
25°C 0.2 2 0.2 2
nA
IIO Input offset current Full range 6 6 nA
I
Input bias current
25°C −15 −50 −15 −50
nA
IIB Input bias current Full range −90 −90 nA
VI
C
RCommon-mode
input voltage range
25°C0
to 3.5
−0.3
to 3.8
0
to 3.5
−0.3
to 3.8 V
VICR
input voltage range Full range 0 to 3 0 to 3
V
Output low, No load 25°C 15 25 15 25
Output low, 25°C 5 10 5 10
mV
Mi k tt
Output
low
,
RL = 600 Ω to GND Full range 13 13 mV
VOM
Maximum peak output
voltage swing
Output low, Isink = 1 mA 25°C 220 350 220 350
VOM
vo
lt
age sw
i
ng
Output high, No load 25°C 4 4.4 4 4.4
Output hi
g
h, 25°C 3.4 4 3.4 4 V
Output
high
,
RL = 600 Ω to GND Full range 3.2 3.2
V
AVD
Large-signal differential
voltage amplification
VO = 5 mV to 4 V,
RL = 500 Ω25°C 1 1 V/µV
I
Suppl
y
current 25°C 0.3 0.5 0.3 0.5
mA
ICC
Supply
current
per amplifier Full range 0.55 0.55 mA
†Full range is 0°C to 70°C.
operating characteristics, VCC± = ±15 V, VIC = 0, TA = 25°C
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SR Slew rate 0.2 0.4 V/µs
V
Equivalent input noise voltage
f = 10 Hz 24
nV/√Hz
VnEquivalent input noise voltage f = 1 kHz 22 nV/√Hz
VN(PP) Peak-to-peak equivalent input noise voltage f = 0.1 Hz to 10 Hz 0.55 µV
InEquivalent input noise current f = 10 Hz 0.07 pA/√Hz
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VCC± = ±15 V, VIC = 0 (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
T†
LT1014I LT1014DI
UNIT
PARAMETER TEST CONDITIONS TA†
MIN TYP‡MAX MIN TYP‡MAX UNIT
V
Input offset voltage
R50 Ω
25°C 60 300 200 800
V
VIO Input offset voltage RS = 50 ΩFull range 550 1000 µV
aVIO
Temperature coeficient
of input offset voltage Full range 0.4 2.5 0.7 5 µV/°C
Long-term drift
of input offset voltage 25°C 0.5 0.5 µV/mo
I
Input offset current
25°C 0.15 1.5 0.15 1.5
nA
IIO Input offset current Full range 2.8 2.8 nA
I
Input bias current
25°C −12 −30 −12 −30
nA
IIB Input bias current Full range −38 −38 nA
V
ICR
Common-mode
input voltage range
25°C
−15
to
13.5
−15.3
to
13.8
−15
to
13.5
−15.3
to
13.8 V
VICR
input voltage range
Full range −15
to 13
−15
to 13
V
V
Maximum peak
R2kΩ
25°C±12.5 ±14 ±12.5 ±14
V
VOM
Maximum
peak
output voltage swing RL = 2 kΩFull range ±12 ±12 V
L i l diff ti l
VO = ±10 V, RL = 600 Ω25°C 0.5 2 0.5 2
AVD
Large-signal differential
voltage amplification
V±10 V
R2kΩ
25°C 1.2 8 1.2 8 V/µV
AVD
vo
lt
age amp
lifi
ca
ti
on VO = ±10 V, RL = 2 kΩFull range 0.7 0.7
V/µV
CMRR
Common-mode
V15Vto135V
25°C 97 117 97 117
dB
CMRR
Common mode
rejection ratio VIC = −15 V to 13.5 V Full range 94 94 dB
k
Supply-voltage
rejection ratio
V±2Vto±18 V
25°C 100 117 100 117
dB
kSVR rejection ratio
(∆VCC/∆VIO)
VCC± = ±2 V to ±18 V
Full range 97 97
dB
Channel separation VO = ±10 V, RL = 2 kΩ25°C 120 137 120 137 dB
rid
Differential
input resistance 25°C 70 300 70 300 MΩ
ric
Common-mode
input resistance 25°C 4 4 GΩ
I
Suppl
y
current 25°C 0.35 0.55 0.35 0.55
mA
ICC
Supply
current
per amplifier Full range 0.6 0.6 mA
†Full range is −40°C to 105°C.
‡All typical values are at TA = 25°C.
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
8POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VCC+ = 5 V, VCC− = 0, VO = 1.4 V, VIC = 0
(unless otherwise noted)
PARAMETER
TEST CONDITIONS
T†
LT1014I LT1014DI
UNIT
PARAMETER TEST CONDITIONS TA†
MIN TYP MAX MIN TYP MAX UNIT
V
Input offset voltage
R50 Ω
25°C 90 450 250 950
V
VIO Input offset voltage RS = 50 ΩFull range 570 1200 µV
I
Input offset current
25°C 0.2 2 0.2 2
nA
IIO Input offset current Full range 6 6 nA
I
Input bias current
25°C −15 −50 −15 −50
nA
IIB Input bias current Full range −90 −90 nA
VI
C
RCommon-mode
input voltage range
25°C0
to 3.5
−0.3
to 3.8
0
to 3.5
−0.3
to 3.8 V
VICR
input voltage range Full range 0 to 3 0 to 3
V
Output low, No load 25°C 15 25 15 25
Output low, 25°C 5 10 5 10
mV
Mi k
Output
low
,
RL = 600 Ω to GND Full range 13 13 mV
VOM
Maximum peak
output voltage swing
Output low, Isink = 1 mA 25°C 220 350 220 350
VOM
ou
t
pu
t
vo
lt
age sw
i
ng
Output high, No load 25°C 4 4.4 4 4.4
Output hi
g
h, 25°C 3.4 4 3.4 4 V
Output
high
,
RL = 600 Ω to GND Full range 3.2 3.2
V
AVD
Large-signal differential
voltage amplification
VO = 5 mV to 4 V,
RL = 500 Ω25°C 1 1 V/µV
I
Suppl
y
current 25°C 0.3 0.5 0.3 0.5
mA
ICC
Supply
current
per amplifier Full range 0.55 0.55 mA
†Full range is −40°C to 105°C.
operating characteristics, VCC+ = ±15 V, VIC = 0, TA = 25°C
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SR Slew rate 0.2 0.4 V/µs
V
Equivalent input noise voltage
f = 10 Hz 24
nV/√H
VnEquivalent input noise voltage f = 1 kHz 22 nV/√Hz
VN(PP) Peak-to-peak equivalent input noise voltage f = 0.1 Hz to 10 Hz 0.55 µV
InEquivalent input noise current f = 10 Hz 0.07 pA/√Hz
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VCC± = ±15 V, VIC = 0 (unless otherwise
noted)
PARAMETER
TEST
T†
LT1014M LT1014AM LT1014DM
UNIT
PARAMETER
TEST
CONDITIONS TA†
MIN TYP‡MAX MIN TYP‡MAX MIN TYP‡MAX UNIT
V
Input offset
R50 Ω
25°C 60 300 60 180 200 800
V
VIO
Input
offset
voltage RS = 50 ΩFull range 550 350 1000 µV
aVIO
Temperature
coefficient of
input offset
voltage
Full range 0.5 2.5 0.5 2 0.5 2.5 µV/°C
Long-term drift
of input offset
voltage
25°C 0.5 0.5 0.5 µV/mo
I
Input offset 25°C 0.15 1.5 0.15 0.8 0.15 1.5
nA
IIO
Input
offset
current Full range 5 2.8 5 nA
I
Input bias 25°C −12 −30 −12 −20 −12 −30
nA
IIB
Input
bias
current Full range −45 −30 −45 nA
V
ICR
Common-mode
in
p
ut volta
g
e
25°C
−15
to
13.5
−15.3
to
13.8
−15
to
13.5
−15.3
to
13.8
−15
to
13.5
−15.3
to
13.8 V
VICR
input
voltage
range Full range −14.9
to 13
−14.9
to 13
−14.9
to 13
V
V
Maximum peak
output voltage
R2kΩ
25°C±12.5 ±14 ±13 ±14 ±12.5 ±14
V
VOM output voltage
swing
RL = 2 kΩ
Full range ±11.5 ±12 ±11.5
V
A
Large-signal
differential
VO = ±10 V,
RL = 600 Ω25°C 0.5 2 0.8 2.2 0.5 2
V/ V
AVD
differential
voltage V
O
= ±10 V, 25°C 1.2 8 1.5 8 1.2 8 V/µV
voltage
amplification
VO
=
±10
V
,
RL = 2 kΩFull range 0.25 0.4 0.25
CMRR
Common-mode
VIC = −15 V to
13.5 V 25°C 97 117 100 117 97 117
dB
CMRR
Common mode
rejection ratio VIC = −14.9 V
to 13 V Full range 94 96 94
dB
k
Supply-voltage
rejection ratio
V
CC
± = ±2 V to 25°C 100 117 103 117 100 117
dB
kSVR rejection ratio
(∆VCC/∆VIO)
VCC±
=
±2
V
to
±18 V Full range 97 100 97
dB
Channel
separation
VO = ±10 V,
RL = 2 kΩ25°C 120 137 123 137 120 137 dB
rid
Differential input
resistance 25°C 70 300 100 300 70 300 MΩ
ric
Common-mode
input resistance 25°C 4 4 4 GΩ
I
Suppl
y
current 25°C 0.35 0.55 0.35 0.50 0.35 0.55
mA
ICC
Supply
current
per amplifier Full range 0.7 0.6 0.7 mA
†Full range is −55°C to 125°C.
‡All typical values are at TA = 25°C.
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
10 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, VCC+ = 5 V, VCC− = 0, VO = 1.4 V, VIC = 0
(unless otherwise noted)
PARAMETER
TEST
T†
LT1014M LT1014AM LT1014DM
UNIT
PARAMETER
TEST
CONDITIONS TA†
MIN TYP MAX MIN TYP MAX MIN TYP MAX UNIT
R50Ω
25°C 90 450 90 280 250 950
VIO
Input RS = 50ΩFull range 400 1500 400 960 800 2000
µV
V
IO
Input
offset voltage RS = 50Ω,
VIC = 0.1 V 125°C 200 750 200 480 560 1200
µ
V
I
Input 25°C 0.2 2 0.2 1.3 0.2 2
IIO
Input
offset current Full range 10 7 10
nA
I
Input 25°C −15 −50 −15 −35 −15 −50 nA
IIB
Input
bias current Full range −120 −90 −120
V
Common-
mode input
25°C0
to 3.5
−0.3
to 3.8
0
to 3.5
−0.3
to 3.8
0
to 3.5
−0.3
to 3.8
V
VICR mode input
voltage range Full range 0.1
to 3
0.1
to 3
0.1
to 3
V
Output low,
No load 25°C 15 25 15 25 15 25
Output low,
R600Ωto
25°C 5 10 5 10 5 10
mV
RL = 600Ω to
GND Full range 18 15 18
mV
VOM Maximum
peak output
voltage swing
Output low,
Isink = 1 mA 25°C 220 350 220 350 220 350
voltage swing Output high,
No load 25°C 4 4.4 4 4.4 4 4.4
Output high, 25°C 3.4 4 3.4 4 3.4 4 V
RL = 600Ω to
GND Full range 3.1 3.2 3.1
V
AVD
Large-signal
differential
voltage
amplification
VO = 5 mV to 4 V,
RL = 500Ω25°C 1 1 1 V/µV
I
Suppl
y
current 25°C 0.3 0.5 0.3 0.45 0.3 0.5
mA
ICC
Supply
current
per amplifier Full range 0.65 0.55 0.65 mA
†Full range is −55°C to 125°C.
operating characteristics, VCC±= ±15 V, VIC = 0, TA = 25°C
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SR Slew rate 0.2 0.4 V/µs
V
Equivalent input noise voltage
f = 10 Hz 24
nV/√H
VnEquivalent input noise voltage f = 1 kHz 22 nV/√Hz
VN(PP) Peak-to-peak equivalent input noise voltage f = 0.1 Hz to 10 Hz 0.55 µV
InEquivalent input noise current f = 10 Hz 0.07 pA/√Hz
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
11
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
VIO Input offset voltage vs Balanced source resistance 1
VIO Input offset voltage vs Free-air temperature 2
∆VIO Warm-Up Change in input offset voltage vs Elapsed time 3
IIO Input offset current vs Free-air temperature 4
IIB Input bias current vs Free-air temperature 5
VIC Common-mode input voltage vs Input bias current 6
A
Differential voltage amplification
vs Load resistance 7, 8
AVD Differential voltage amplification vs Frequency 9, 10
Channel separation vs Frequency 11
Output saturation voltage vs Free-air temperature 12
CMRR Common-mode rejection ratio vs Frequency 13
kSVR Supply-voltage rejection ratio vs Frequency 14
ICC Supply current vs Free-air temperature 15
IOS Short-circuit output current vs Elapsed time 16
VnEquivalent input noise voltage vs Frequency 17
InEquivalent input noise current vs Frequency 17
VN(PP) Peak-to-peak input noise voltage vs Time 18
Pulse response (small signal) vs Time 19, 21
Pulse response (large signal) vs Time 20, 22, 23
Phase shift vs Frequency 9
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
12 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS†
Figure 1
Rs − Source Resistance − Ω
LT1014
INPUT OFFSET VOLTAGE
vs
BALANCED SOURCE RESISTANCE
− Input Offset Voltage − mV
1 k
0.01
0.1
1
10
−
+
TA = 25°C
VCC±= 5 V
VCC− = 0
VIO
VCC± = ±15 V
RS
RS
3 k 10 k 30 k 100 k 300 k 1 M 3 M 10 M
Figure 2
TA − Free-Air Temperature − °C
INPUT OFFSET VOLTAGE
OF REPRESENTATIVE UNITS
vs
FREE-AIR TEMPERATURE
VCC± = ±15 V
Vµ− Input Offset Voltage −VIO
250
200
150
100
50
0
−50
−100
−150
−200
−250
−50 −25 0 25 50 75 100 125
3
2
1
00123
− Change in Input Offset Votlage −
4
t − Time After Power-On − min
WARM-UP CHANGE IN INPUT OFFSET VOLTAGE
vs
ELAPSED TIME
5
45
N Package
VCC± = ±15 V
TA = 25°C
∆VIO
J Package
Vµ
Figure 3
0.2
0
INPUT OFFSET CURRENT
vs
FREE-AIR TEMPERATURE
1
0.4
0.6
0.8
VIC = 0
VCC± = ±2.5 V
TA − Free-Air Temperature − °C
VCC+ = 5 V, VCC− = 0
−50 −25 0 25 50 75 100 125
− Input Offset Current − nAIIO
VCC± = ±15 V
Figure 4
†Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
13
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS†
Figure 5
TA − Free-Air Temperature − °C
INPUT BIAS CURRENT
vs
FREE-AIR TEMPERATURE
VIC = 0
VCC+= 5 V, VCC− = 0
VCC± = ±2.5 V
VCC± = ±15 V
− Input Bias Current − nAIIB
−30
−25
−20
−15
−10
−5
0
−50 −25 0 25 50 75 100 125
Figure 6
IIB − Input Bias Current − nA
COMMON-MODE INPUT VOLTAGE
vs
INPUT BIAS CURRENT
TA = 25°C
VCC± = ±15 V
(Left Scale) VCC+ = 5 V
VCC− = 0
(Right Scale)
− Common-Mode Input Voltage − VVIC
15
10
5
0
−5
−10
−15
0 −5 −10 −15 −20 −25 −30
5
3
4
2
1
0
−1
− Common-Mode Input Voltage − VVIC
Figure 7
RL − Load Resistance − Ω
DIFFERENTIAL VOLTAGE AMPLIFICATION
vs
LOAD RESISTANCE
VCC± = ±15 V
VO = ±10 V
TA = −55°C
TA = 25°C
TA = 125°C
Vµ− Differential Voltage Amplivication − V/AVD
100 400 1 k 4 k 10 k
10
4
1
0.4
0.1
Figure 8
DIFFERENTIAL VOLTAGE AMPLIFICATION
vs
LOAD RESISTANCE
VCC+ = 5 V, VCC− = 0
VO = 20 mV to 3.5 V
TA = −55°C
TA = 25°C
TA = 125°C
Vµ− Differential Voltage Amplivication − V/AVD
RL − Load Resistance − Ω
100 400 1 k 4 k 10 k
10
4
1
0.4
0.1
†Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
14 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS†
Figure 9
f − Frequency − MHz
DIFFERENTIAL VOLTAGE AMPLIFICATION
AND PHASE SHIFT
vs
FREQUENCY
AVD
VCC+ = 5 V
VCC− = 0
VCC± = ±15 V
VIC = 0
CL = 100 pF
TA = 25°C
VCC+ = 5 V
VCC− = 0
φ
VCC± = ±15 V
− Differential Voltage Amplivication − dBAVD
− Phase Shift
20
10
0
−10
0.01 0.3 1 3 10
80°
100°100°
120°
140°
160°
180°
200°
220°
240°
Figure 10
DIFFERENTIAL VOLTAGE AMPLIFICATION
vs
FREQUENCY
VCC + = 5 V
VCC − = 0 VCC± = ±15 V
CL = 100 pF
TA = 25°C
− Differential Voltage Amplivication − dBAVD
f − Frequency − Hz
0.01 0.1 1 k 100 k 10 M1 10 100 10 k 1 M
0
−20
20
40
60
80
100
120
140
Figure 11
120
100
80
6010 100 1 k 10 k
Channel Separation − dB
140
f − Frequency − Hz
CHANNEL SEPARATION
vs
FREQUENCY
160
100 k 1 M
Limited by
Thermal
Interaction RL = 100 Ω
RL = 1 kΩ
Limited by
Pin-to-Pin
Capacitance
VCC± = ±15 V
VI(PP) = 20 V to 5 kHz
RL = 2 kΩ
TA = 25°C
Figure 12
Output Saturation Voltage − V
OUTPUT SATURATION VOLTAGE
vs
FREE-AIR TEMPERATURE
TA − Free-Air Temperature − °C
VCC+ = 5 V to 30 V
VCC− = 0
Isink = 10 mA
Isink = 1 mA
Isink = 100 µA
Isink = 10 µA
Isink = 0
Isink = 5 mA
10
1
0.1
0.01
−50 −25 0 25 50 75 100 125
†Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
15
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS†
Figure 13
60
40
20
0
10 100 1 k 10 k
CMRR − Common-Mode Rejection Ratio − dB
80
100
f − Frequency − Hz
COMMON-MODE REJECTION RATIO
vs
FREQUENCY
120
100 k 1 M
VCC+ = 5 V
VCC− = 0
VCC± = ±15 V
TA = 25°C
Figure 14
0.1 1 10 100 1 k
SUPPLY-VOLTAGE REJECTION RATIO
vs
FREQUENCY
10 k 100 k 1 M
0
20
40
60
80
100
120
140
f − Frequency − Hz
Negative
Supply
Positive
Supply
VCC± = ± 15 V
TA = 25°C
− Supply-Voltage Rejection Ratio − dBKSVR
Figure 15
− Supply Current Per Amplifier −
TA − Free-Air Temperature − °C
SUPPLY CURRENT
vs
FREE-AIR TEMPERATURE
0 25 50 75 100 125
260
300
340
380
420
460
VCC+ = 5 V
VCC− = 0
VCC± = ±15 V
−25−50
AµICC
Figure 16
01
0
10
t − Time − min
SHORT-CIRCUIT OUTPUT CURRENT
vs
ELAPSED TIME
20
23
30
40
TA = 25°C
TA = 125°C
TA = 25°C
TA = −55°C
TA = 125°C
VCC± = ±15 V
TA = −55°C
−10
−20
−30
−40
− Short-Circuit Output Current − mAIOS
†Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
16 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 17
100
1000
300
110
f − Frequency − Hz
EQUIVALENT INPUT NOISE VOLTAGE
AND EQUIVALENT INPUT NOISE CURRENT
vs
FREQUENCY
30
10 100
VCC± = ±2 V to ±18 V
TA = 25°C
In
Vn
100
1000
300
30
10
1 k
1/f Corner = 2 Hz
− Equivalent Input Noise Current − InfA/ Hz
− Equivalent Input Noise Voltage −VnfA/ Hz
Figure 18
1200
800
400
00246
1600
t − Time − s
PEAK-TO-PEAK INPUT NOISE VOLTAGE
OVER A 10-SECOND PERIOD
vs
TIME
2000
810
VCC± = ±2 V to ±18 V
f = 0.1 Hz to 10 Hz
TA = 25°C
− Noise Voltage − nVVN(PP)
Figure 19
t − Time − µs
0
46810
60
80
12 14
40
20
20
VCC± = ±15 V
AV = 1
TA = 25°C
VOLTAGE-FOLLOWER SMALL-SIGNAL
PULSE RESPONSE
vs
TIME
−20
−40
−60
−80
− Output Voltage − mVVO
Figure 20
2
0102030
3
5
VOLTAGE-FOLLOWER LARGE-SIGNAL
PULSE RESPONSE
vs
TIME
6
40 50 60 70
4
t − Time − µs
VCC+ = 5 V
VCC− = 0
VI = 0 to 4 V
RL = 0
AV = 1
TA = 25°C
1
0
−1
−2
− Output Voltage − VVO
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
17
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 21
t − Time − µs
60
40
0
0204060
80
120
VOLTAGE-FOLLOWER SMALL-SIGNAL
PULSE RESPONSE
vs
TIME
140
80 100 120 140
20
100
160 VCC+ = 5 V
VCC− = 0
VI = 0 to 100 mV
RL = 600 Ω to GND
AV = 1
TA = 25°C
−20
− Output Voltage − mVVO
VOLTAGE-FOLLOWER LARGE-SIGNAL
PULSE RESPONSE
vs
TIME
Figure 22
t − Time − µs
2
1
0102030
3
5
6
40 50 60 70
0
4
VCC+ = 5 V
VCC− = 0
VI = 0 to 4 V
RL = 4.7 kΩ to 5 V
AV = 1
TA = 25°C
−1
−2
− Output Voltage − mVVO
t − Time − µs
2
1
0102030
3
5
6
40 50 60 70
0
4
VCC+ = 5 V
VCC− = 0
VI = 0 to 4 V
RL = 0
AV = 1
TA = 25°C
VOLTAGE-FOLLOWER LARGE-SIGNAL
PULSE RESPONSE
vs
TIME
−1
−2
− Output Voltage − VVO
Figure 23
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
18 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
single-supply operation
The LT1014 is fully specified for single-supply operation (VCC− = 0). The common-mode input voltage range
includes ground, and the output swings within a few millivolts of ground.
Furthermore, the LT1014 has specific circuitry that addresses the difficulties of single-supply operation, both
at the input and at the output. At the input, the driving signal can fall below 0 V, either inadvertently or on a
transient basis. If the input is more than a few hundred millivolts below ground, the LT1014 is designed to deal
with the following two problems that can occur:
1. On many other operational amplifiers, when the input is more than a diode drop below ground, unlimited
current flows from the substrate (VCC− terminal) to the input, which can destroy the unit. On the LT1014,
the 400-Ω resistors in series with the input (see schematic) protect the device even when the input is 5 V
below ground.
2. When the input is more than 400 mV below ground (at TA = 25°C), the input stage of similar type operational
amplifiers saturates, and phase reversal occurs at the output. This can cause lockup in servo systems.
Because of unique phase-reversal protection circuitry (Q21, Q22, Q27, and Q28), the LT1014 outputs do
not reverse, even when the inputs are at −1.5 V (see Figure 24).
However, this phase-reversal protection circuitry does not function when the other operational amplifier on the
LT1014 is driven hard into negative saturation at the output. Phase-reversal protection does not work on an
amplifier:
DWhen 4’s output is in negative saturation (the outputs of 2 and 3 have no effect)
DWhen 3’s output is in negative saturation (the outputs of 1 and 4 have no effect)
DWhen 2’s output is in negative saturation (the outputs of 1 and 4 have no effect)
DWhen 1’s output is in negative saturation (the outputs of 2 and 3 have no effect)
At the output, other single-supply designs either cannot swing to within 600 mV of ground or cannot sink more
than a few microproamperes while swinging to ground. The all-npn output stage of the LT1014 maintains its low
output resistance and high gain characteristics until the output is saturated. In dual-supply operations, the output
stage is free of crossover distortion.
(a) VI(PP) = −1.5 V to 4.5 V (b) Output Phase Reversal
Exhibited by LM358
(c) No Phase Reversal
Exhibited by LT1014
− Input Voltage − VVI(PP)
− Output Voltage − VVO
− Output Voltage − VVO
5
4
3
2
1
0
−1
−2
5
4
3
2
1
0
−1
5
4
3
2
1
0
−1
Figure 24. Voltage-Follower Response
With Input Exceeding the Negative Common-Mode Input Voltage Range
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
19
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
comparator applications
The single-supply operation of the LT1014 can be used as a precision comparator with TTL-compatible output.
In systems using both operational amplifiers and comparators, the LT1014 can perform multiple duties (see
Figures 25 and 26).
Figure 25. Low-to-High-Level Output Response
for Various Input Overdrives
100 mV
10 mV 5 mV 2 mV
Differential
Input Voltage
t − Time − µs
Overdrive
VCC+ = 5 V
VCC− = 0
TA = 25°C
− Output Voltage − VVO
5
4
3
2
1
0
0 50 100 150 200 250 300 350 400 450
Figure 26. High-to-Low-Level Output Response
for Various Input Overdrives
2 mV5 mV
100 mV
Overdrive
10 mV
Differential
Input Voltage
t − Time − µs
VCC+ = 5 V
VCC− = 0
TA = 25°C
− Output Voltage − VVO
5
4
3
2
1
0
0 50 100 150 200 250 300 350 400 450
low-supply operation
The minimum supply voltage for proper operation of the LT1014 is 3.4 V (three Ni-Cad batteries). Typical supply
current at this voltage is 290 µA; therefore, power dissipation is only 1 mW per amplifier.
offset voltage and noise testing
Figure 30 shows the test circuit for measuring input offset voltage and its temperature coefficient. This circuit
with supply voltages increased to ±20 V is also used as the burn-in configuration.
The peak-to-peak equivalent input noise voltage of the LT1014 is measured using the test circuit shown in
Figure 27. The frequency response of the noise tester indicates that the 0.1-Hz corner is defined by only one
zero. The test time to measure 0.1-Hz to 10-Hz noise should not exceed 10 seconds, as this time limit acts as
an additional zero to eliminate noise contribution from the frequency band below 0.1 Hz.
An input noise-voltage test is recommended when measuring the noise of a large number of units. A 10-Hz input
noise-voltage measurement correlates well with a 0.1-Hz peak-to-peak noise reading because both results are
determined by the white noise and the location of the 1/f corner frequency.
Noise current is measured by the circuit and formula shown in Figure 28. The noise of the source resistors is
subtracted.
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
20 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
10 Ω
100 kΩ
0.1 µF
2 kΩ
4.7 µF
AVD = 50,000
24.3 kΩ
100 kΩ
0.1 µF
4.3 kΩ
2.2 µF
110 kΩ
22 µF
Oscilloscope
Rin = 1 MΩ
NOTE A: All capacitor values are for nonpolarized capacitors only.
LT1014
+
−LT1001
+
−
Figure 27. 0.1-Hz to 10-Hz Peak-to-Peak Noise Test Circuit
10 kΩ
10 Mن
100 ΩVnIn+ƪVno2*(820 nV)2ƫ1ń2
40 MW 100
†Metal-film resistor
10 Mن
10 Mن10 MنLT1014
+
−
Figure 28. Noise-Current Test Circuit and Formula
15 V
−15 V
VO = 1000 VIO
100 Ω
(see Note A)
50 Ω
(see Note A)
LT1014
+
−
50 Ω
(see Note A)
NOTE A: Resistors must have low thermoelectric potential.
Figure 29. Test Circuit for VIO and αVIO
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
21
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
5 V
100 pF
2 kΩ
Q4
2N2222
Q3
2N2905
5 V
68 Ω
4.3 kΩ
LT1004
1.2 V
4 kن
10 kن
1 kΩ
4-mA
Trim
IN
0 to 4 V
4-mA to 20-mA OUT
To Load
2.2 kΩ Max
100 Ω†
10 Ω†
10 kن
20-mA
Trim
80 Ω†
100 kΩ
5 V
0.33 µF
10 kΩ820 ΩQ2
2N2905
SN74HC04 (6)
820 Ω
Q1
2N2905
1N4002 (4)
10 µF
10 µF
T1‡
0.002 µF
1/4
LT1014
1/4
LT1014
†1% film resistor. Match 10-kΩ resistors 0.05%.
‡T1 = PICO-31080
+
±
+
±
+
+
10 kΩ10 kΩ
Figure 30. 5-V Powered, 4-mA to 20-mA Current-Loop Transmitter With 12-Bit Accuracy
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
22 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
To
Inverter
Driver
5 V
100 kΩ
10 kن
68 kن
4.3 kΩ
5 V
LT1004
1.2 V
4 kن
2 kΩ
4-mA
Trim
IN
0 to 4 V
1 kΩ
20-mA
Trim
301 Ω†
0.1 ΩT1
10 µF
4-mA to 20-mA OUT
Fully Floating
1N4002 (4)
†1% film resistor
+
−
1/4
LT1014
1/4
LT1014
+
−
+
Figure 31. Fully Floating Modification to 4-mA to 20-mA Current-Loop Transmitter With 8-Bit Accuracy
IN+
IN−
5 V
OUT A
R2
R1
1 µF1 µF
1/2 LTC1043
NOTE A: VIO = 150 µV, AVD = (R1/R2) + 1, CMRR = 120 dB, VICR = 0 to 5 V
1/4
LT1014
+
−
6
18 15
5
6
8
4
7
2
3
IN+
IN−
OUT B
R2
R1
1 µF1 µF
1/2 LTC1043
1/4
LT1014
+
−
7
13 14
3
2
1
11
12
5
8
0.01 µF
Figure 32. 5-V Single-Supply Dual Instrumentation Amplifier
LT1014, LT1014A, LT1014D
QUAD PRECISION OPERATIONAL AMPLIFIERS
SLOS039D − JULY 1989 − REVISED AUGUST 2009
23
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
To Input
Cable Shields
RG (2 kΩ Typ)
200 kΩ
10 kΩ
10 kن
10 kن
OUT
20 kΩ
20 kΩ
200 kن
5 V
IN−
IN+
1 µF
‡
††
1% film resistor. Match 10-kΩ resistors 0.05%.
‡For high source impedances, use 2N2222 as diodes (with collector connected to base).
NOTE A: AVD = (400,000/RG) + 1
LT1014
+
−
LT1014
−
+
LT1014
−
+
LT1014
−
+
5 V
‡
10 kΩ
10 kن
5 V
10 kن
2
3
6
5
‡
‡
1
7
10
9
13
12
14
8
4
11
Figure 33. 5-V Powered Precision Instrumentation Amplifier
PACKAGE OPTION ADDENDUM
www.ti.com 24-Aug-2018
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
5962-89677012A ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-
89677012A
LT1014
AMFKB
5962-8967701CA ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type -55 to 125 5962-8967701CA
LT1014AMJB
5962-89677022A ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-
89677022A
LT1014MFKB
5962-8967702CA ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type -55 to 125 5962-8967702CA
LT1014MJB
LT1014AMFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type 5962-
89677012A
LT1014
AMFKB
LT1014AMJ ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type LT1014AMJ
LT1014AMJB ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type 5962-8967701CA
LT1014AMJB
LT1014CN ACTIVE PDIP N 14 25 Green (RoHS
& no Sb/Br) CU NIPDAU N / A for Pkg Type 0 to 70 LT1014CN
LT1014CNE4 ACTIVE PDIP N 14 25 Green (RoHS
& no Sb/Br) CU NIPDAU N / A for Pkg Type 0 to 70 LT1014CN
LT1014DDW ACTIVE SOIC DW 16 40 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 LT1014D
LT1014DDWE4 ACTIVE SOIC DW 16 40 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 LT1014D
LT1014DDWG4 ACTIVE SOIC DW 16 40 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 LT1014D
LT1014DDWR ACTIVE SOIC DW 16 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 LT1014D
LT1014DDWRE4 ACTIVE SOIC DW 16 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 LT1014D
LT1014DIDW ACTIVE SOIC DW 16 40 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 105 LT1014DI
PACKAGE OPTION ADDENDUM
www.ti.com 24-Aug-2018
Addendum-Page 2
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LT1014DIDWG4 ACTIVE SOIC DW 16 40 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 105 LT1014DI
LT1014DIDWR ACTIVE SOIC DW 16 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 105 LT1014DI
LT1014DIN ACTIVE PDIP N 14 25 Green (RoHS
& no Sb/Br) CU NIPDAU N / A for Pkg Type -40 to 105 LT1014DIN
LT1014DINE4 ACTIVE PDIP N 14 25 Green (RoHS
& no Sb/Br) CU NIPDAU N / A for Pkg Type -40 to 105 LT1014DIN
LT1014DMDW ACTIVE SOIC DW 16 40 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 LT1014DM
LT1014DMDWG4 ACTIVE SOIC DW 16 40 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -55 to 125 LT1014DM
LT1014DN ACTIVE PDIP N 14 25 Green (RoHS
& no Sb/Br) CU NIPDAU N / A for Pkg Type 0 to 70 LT1014DN
LT1014MFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 5962-
89677022A
LT1014MFKB
LT1014MJ ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type -55 to 125 LT1014MJ
LT1014MJB ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type 5962-8967702CA
LT1014MJB
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
PACKAGE OPTION ADDENDUM
www.ti.com 24-Aug-2018
Addendum-Page 3
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF LT1014D :
•Enhanced Product: LT1014D-EP
NOTE: Qualified Version Definitions:
•Enhanced Product - Supports Defense, Aerospace and Medical Applications
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LT1014DDWR SOIC DW 16 2000 330.0 16.4 10.75 10.7 2.7 12.0 16.0 Q1
LT1014DIDWR SOIC DW 16 2000 330.0 16.4 10.75 10.7 2.7 12.0 16.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 14-Jul-2012
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LT1014DDWR SOIC DW 16 2000 367.0 367.0 38.0
LT1014DIDWR SOIC DW 16 2000 367.0 367.0 38.0
PACKAGE MATERIALS INFORMATION
www.ti.com 14-Jul-2012
Pack Materials-Page 2
www.ti.com
PACKAGE OUTLINE
C
14X .008-.014
[0.2-0.36]
TYP
-15
0
AT GAGE PLANE
-.314.308 -7.977.83[ ]
14X -.026.014 -0.660.36[ ]
14X -.065.045 -1.651.15[ ]
.2 MAX TYP
[5.08] .13 MIN TYP
[3.3]
TYP-.060.015 -1.520.38[ ]
4X .005 MIN
[0.13]
12X .100
[2.54]
.015 GAGE PLANE
[0.38]
A
-.785.754 -19.9419.15[ ]
B -.283.245 -7.196.22[ ]
CDIP - 5.08 mm max heightJ0014A
CERAMIC DUAL IN LINE PACKAGE
4214771/A 05/2017
NOTES:
1. All controlling linear dimensions are in inches. Dimensions in brackets are in millimeters. Any dimension in brackets or parenthesis are for
reference only. Dimensioning and tolerancing per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This package is hermitically sealed with a ceramic lid using glass frit.
4. Index point is provided on cap for terminal identification only and on press ceramic glass frit seal only.
5. Falls within MIL-STD-1835 and GDIP1-T14.
78
14
1
PIN 1 ID
(OPTIONAL)
SCALE 0.900
SEATING PLANE
.010 [0.25] C A B
www.ti.com
EXAMPLE BOARD LAYOUT
ALL AROUND
[0.05] MAX.002
.002 MAX
[0.05]
ALL AROUND
SOLDER MASK
OPENING
METAL
(.063)
[1.6]
(R.002 ) TYP
[0.05]
14X ( .039)
[1]
( .063)
[1.6]
12X (.100 )
[2.54]
(.300 ) TYP
[7.62]
CDIP - 5.08 mm max heightJ0014A
CERAMIC DUAL IN LINE PACKAGE
4214771/A 05/2017
LAND PATTERN EXAMPLE
NON-SOLDER MASK DEFINED
SCALE: 5X
SEE DETAIL A SEE DETAIL B
SYMM
SYMM
1
78
14
DETAIL A
SCALE: 15X
SOLDER MASK
OPENING
METAL
DETAIL B
13X, SCALE: 15X
GENERIC PACKAGE VIEW
Images above are just a representation of the package family, actual package may vary.
Refer to the product data sheet for package details.
DW 16 SOIC - 2.65 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
4040000-2/H
www.ti.com
PACKAGE OUTLINE
C
TYP
10.63
9.97
2.65 MAX
14X 1.27
16X 0.51
0.31
2X
8.89
TYP
0.33
0.10
0 - 8 0.3
0.1
(1.4)
0.25
GAGE PLANE
1.27
0.40
A
NOTE 3
10.5
10.1
BNOTE 4
7.6
7.4
4220721/A 07/2016
SOIC - 2.65 mm max heightDW0016A
SOIC
NOTES:
1. All linear dimensions are in millimeters. Dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0.15 mm, per side.
4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm, per side.
5. Reference JEDEC registration MS-013.
116
0.25 C A B
9
8
PIN 1 ID
AREA
SEATING PLANE
0.1 C
SEE DETAIL A
DETAIL A
TYPICAL
SCALE 1.500
www.ti.com
EXAMPLE BOARD LAYOUT
0.07 MAX
ALL AROUND 0.07 MIN
ALL AROUND
(9.3)
14X (1.27)
R0.05 TYP
16X (2)
16X (0.6)
4220721/A 07/2016
SOIC - 2.65 mm max heightDW0016A
SOIC
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
METAL SOLDER MASK
OPENING
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
OPENING
SOLDER MASK METAL
SOLDER MASK
DEFINED
LAND PATTERN EXAMPLE
SCALE:7X
SYMM
1
89
16
SEE
DETAILS
SYMM
www.ti.com
EXAMPLE STENCIL DESIGN
R0.05 TYP
16X (2)
16X (0.6)
14X (1.27)
(9.3)
4220721/A 07/2016
SOIC - 2.65 mm max heightDW0016A
SOIC
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
SCALE:7X
SYMM
SYMM
1
89
16
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-
compliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2018, Texas Instruments Incorporated
