Evaluation Board User Guide UG-261 One Technology Way * P.O. Box 9106 * Norwood, MA 02062-9106, U.S.A. * Tel: 781.329.4700 * Fax: 781.461.3113 * www.analog.com Evaluation Boards for the AD62x Series and the AD822x Series Instrumentation Amplifiers EVAL-INAMP-62RZ (SOIC or PDIP) 3 generic, easy-to-use evaluation boards Shipped with an assortment of Analog Devices, Inc., in-amps Solder in the in-amp to be tested Test pins already populated Decoupling capacitors already populated EVAL-INAMP-62RZ board Compatible with AD620, AD621, AD622, AD623, AD627, AD8223, and AD8225 in SOIC or PDIP EVAL-INAMP-82RZ board Compatible with AD8221, AD8226, AD8227, AD8228, AD8229, AD8421, AD8428, and AD8429 in SOIC package EVAL-INAMP-82RMZ board Compatible with AD8220, AD8221, AD8226, AD8227, AD8228, AD8236, and AD8421 in MSOP package The EVAL-INAMP-62RZ is designed for evaluation of instrumentation amplifiers in the legacy pinout. This board can be used to evaluate the AD620, AD621, AD622, AD623, AD627, AD8223, and AD8225 instrumentation amplifiers. In addition to the basic in-amp connection, circuit options enable the user to adjust the offset voltage, apply an output reference, or provide shield drivers with user-supplied components. The board is shipped with an assortment of instrumentation amplifier ICs in the legacy SOIC pinout, typically AD620, AD621, AD622, AD623, AD8223, and AD8225. The board also has an alternative footprint for a through-hole, 8-lead PDIP. 09753-001 FEATURES The EVAL-INAMP-82RZ is designed for evaluation of instrumentation amplifiers in the high performance pinout. This board can be used to evaluate the AD8221, AD8226, AD8227, AD8228, AD8229, AD8421, AD8428, and AD8429 in SOIC packages. The board is shipped with an assortment of instrumentation amplifier ICs in the high performance SOIC pinout, typically AD8221, AD8226, AD8421, AD8428, and AD8429. The evaluation board is arranged so that users can easily solder on the gain resistor. The in-amp reference pin can be connected to ground through a solder short or connected to the user's source through the test pin. A small prototyping area allows interfacing to another part in an SOIC package. Users can add their own SMA or SMB connector to interface the evaluation board with complementary tools, such as an analog-to-digital converter (ADC) evaluation board, available from Analog Devices. Figure 1. GENERAL DESCRIPTION This user guide describes three generic evaluation boards that can be used to evaluate many of Analog Devices instrumentation amplifiers. For information on the performance of a specific instrumentation amplifier, see the data sheet for that instrumentation amplifier. PLEASE SEE THE LAST PAGE FOR AN IMPORTANT WARNING AND LEGAL TERMS AND CONDITIONS. EVAL-INAMP-82RZ (SOIC) EVAL-INAMP-82RMZ (MSOP) The EVAL-INAMP-82RMZ board is exactly the same as the EVAL-INAMP-82RZ board, except that is designed for the MSOP pinout. This board can be used to evaluate the AD8220, AD8221, AD8226, AD8227, AD8228, AD8236, and AD8421 in MSOP packages. The EVAL-INAMP-82RMZ board ships with an assortment of in-amp ICs in the high performance MSOP pinout, typically AD8220, AD8221, AD8226, AD8228, and AD8421. Rev. C | Page 1 of 8 UG-261 Evaluation Board User Guide TABLE OF CONTENTS Features .............................................................................................. 1 Guard Drivers ................................................................................5 General Description ......................................................................... 1 Component Locations ..................................................................5 Revision History ............................................................................... 2 User Options ..................................................................................6 EVAL-INAMP-62RZ Details ........................................................... 3 Quick Start for the EVAL-INAMP-62RZ Board .......................... 4 Quick Start for the EVAL-INAMP-82RZ and EVAL-INAMP82RMZ Boards ...................................................................................7 Circuit Options ............................................................................. 4 Reference ........................................................................................7 Load Resistor................................................................................. 4 Output .............................................................................................7 CMRR Performance ..................................................................... 4 REVISION HISTORY 6/12--Rev. B to Rev. C Changes to Features Section, EVAL-INAMP-62RZ (SOIC or PDIP) Section, EVAL-INAMP-82RZ (SOIC) Section, and EVAL-INAMP-82RMZ (MSOP) Section ...................................... 1 Changes to Quick Start for the EVAL-INAMP-82RZ and EVAL-INAMP-82RMZ Boards Section ........................................ 7 3/11--Rev. A to Rev. B Changed Format to User Guide ................................... Throughout Changes to Document Title ............................................................ 1 Changes to Features Section............................................................ 1 Deleted Applications Section .......................................................... 1 Changes to General Description Section ...................................... 1 Added CMRR Performance Section .............................................. 4 Added Component Locations Section ........................................... 5 11/08--Rev. 0 to Rev. A Combined AD623-EVALZ Data Sheet and AD623-EVAL Data Sheet ............................................................................ Universal Added AD8220/AD8221-EVALZ .............................. Throughout Changed AD623-EVALZ to AD620 Series-EVALZ........ Throughout Changes to General Description .....................................................1 Added EVAL-INAMP-62RZ Details Section .................................3 Added Quick Start for the EVAL-INAMP-62RZ Boards Section.....4 Changes to Gain Adjustment Section .............................................4 Added Table 1 and Table 2; Renumbered Sequentially ................4 Changed Appendix Heading to User Options ...............................6 Added Quick Start for the EVAL-INAMP-82RZ Section and EVAL-INAMP-82RMZ Boards Section .........................................7 Changes to Ordering Guide .............................................................8 12/07--Revision 0: AD623-EVALZ Initial Version 6/03--Revision 0: AD623-EVAL Initial Version Rev. C | Page 2 of 8 Evaluation Board User Guide UG-261 EVAL-INAMP-62RZ DETAILS GND2 REMOVE W3 AND W4 FOR AC COUPLING. R2 100 +IN W3 +VS C1, 0.1F +VAUX R3 100k 1 C6 0.1F 8 1 W1 +GUARD W9 3 A2 2 W8 8 R52 R62 W10 5 7 W2 4 W5 A2 6 W15 AD708J C5 0.1F -VAUX C4 0.1F A3 3 AD708J -GUARD COMPONENTS IN SHADED AREAS ARE USER SUPPLIED. RG + 7 +RG OUTPUT -RG REF 5 2 4 - 6 OUTPUT 1 R5 100k 1 C2 0.1F C3, 0.1F W14 R8 W12 EXT_REF +VAUX W13 W11 R4 100 W7 +VS + C12 W4 NOTES 1INSTALL FOR AC COUPLING ONLY. 2TO USE GUARD DRIVER, INSTALL R5 AND R6 INSTEAD OF RG. R5 AND R6 = 0.5RG. +VAUX OP177 CS2 J500 240A OFFSET ADJ. R1 7 3 100k A1 2 R9 5.9k, 1% -VS -IN GND1 C10 0.1F 6 4 R10 5.9k, 1% C9 0.1F -VAUX OP177 10F 25V C7 0.1F CS2 J500 240A C8 0.1F GND W6 -VS C11 10F 25V 09753-002 + -VAUX -VAUX Figure 2. EVAL-INAMP-62RZ (AD62x Series) Schematic Diagram Rev. C | Page 3 of 8 UG-261 Evaluation Board User Guide QUICK START FOR THE EVAL-INAMP-62RZ BOARD CIRCUIT OPTIONS Table 3. AD623 Gain Resistor Values Single-Supply Operation The gain of the AD621 is pin selectable where G = 1 (default) or G = 100 (strap Pin 1 and Pin 8). In contrast, the gain of the AD620, AD622, and AD623 devices is resistor dependent (the resistor is connected between the RG pins). Without a resistor, the gain is unity. Table 1 to Table 3 provide calculated gains for each device. See the individual product data sheet for the gain equations. Desired Gain 2 5 10 20 33 40 50 65 100 200 500 1000 Table 1. AD620 Gain Resistor Values External Reference or Offset Adjustment A jumper is provided to select between single or dual power supplies. The evaluation board is shipped with W14 in the dualsupply position. To convert to single supply, place W14 in the position marked with a ground symbol. Gain Adjustment 1% Standard Value of RG () 49.9 k 12.4 k 5.49 k 2.61 k 1.00 k 499 249 100 49.9 Calculated Gain 1.990 4.984 9.998 19.93 50.40 100.0 199.4 495.0 991.0 0.1% Standard Value of RG () 49.3 k 12.4 k 5.49 k 2.61 k 1.01 k 499 249 98.8 49.3 Calculated Gain 2.002 4.984 9.998 19.93 49.91 100.0 199.4 501.0 1003.0 Table 2. AD622 Gain Resistor Values Desired Gain 2 5 10 20 33 40 50 65 100 200 500 1000 1% Standard Value of RG () 51.1 k 12.7 k 5.62 k 2.67 k 1.58 k 1.3 k 1.02 k 787 511 255 102 51.1 Calculated Gain 1.988 4.976 9.986 19.91 32.96 39.85 50.50 65.17 99.83 199.0 496.1 989.3 1% Standard Value of RG () 100 k 24.9 k 11 k 5.23 k 3.09 k 2.55 k 2.05 k 1.58 k 1.02 k 499 200 100 Calculated Gain 2 5.02 10.09 20.12 33.36 40.21 49.78 64.29 99.04 201.4 501 1001 When shipped, the reference of the EVAL-INAMP-62RZ board is connected to ground. Certain single-supply applications (for example, an ADC connected to the output of the in-amp) require a symmetrical output voltage centered on a nonzero value. The reference can be equal to half the supply, or an application-specific voltage can be provided by an ADC. The user can install a jumper at W13 and connect an external reference to the EXT_REF pin. To maintain proper operation of the in-amp, the reference should be provided by a voltage source. Similarly, a provision is made for an offset adjustment of 1.12 V by installing the parts listed in Table 6. Although the A2 and A3 ICs can be used with a single or dual power supply connection, A1 requires a dual supply. To enable the offset feature, install a shunt in Position W11. To adjust the offset of the in-amp, ground both inputs and measure the output voltage. Adjust Potentiometer R1 for 0 V. LOAD RESISTOR Although not required for normal operation, a load resistor can be inserted at Position R8. CMRR PERFORMANCE The AD621 CMRR performance degrades at gains of 100 when using this board due to the high performance of the AD621. Rev. C | Page 4 of 8 Evaluation Board User Guide UG-261 GUARD DRIVERS COMPONENT LOCATIONS When interference from sources such as power lines must be reduced to levels below those provided by standard shielded cables, guard drivers may be effective. A guard equalizes the ac potential between the in-amp input and the cable shield of the line, effectively reducing the low frequency interference voltage. Figure 3 shows the component layout and the location of connections for the EVAL-INAMP-62RZ board. A2 in Figure 3 is a dual op amp AD708 driving the shield(s) of the input cable(s) from the gain resistor pins of the in-amp. The voltages at these pins are equal to the input voltages plus 0.6 V (see the device data sheet). POWER The EVAL-INAMP-62RZ provides single and differential guards. Differential guards drive the shields with essentially the same signals as the inputs, whereas the single guard can be used for dual conductor cables. In this mode, the +GUARD drives the shield at 1/2(VIN DIFF) + 0.6 V. OUTPUT INPUT Using a Single Guard When using the AD620, AD622, and AD623 for gains greater than 1, install Resistors R6 and R11 (which are each half the calculated resistance of RG) and Jumpers W1, W2, and W10. For a gain of 1, either Position R6 or Position R11 can be shorted to enable the guard driver input. Connect the shield to +GUARD. On the header pins that do not bear the ground symbol, insert a shunt across Position W1. The guard drivers can be assembled using the components listed in Table 6. Rev. C | Page 5 of 8 09753-003 To activate the guard drivers, +VAUX and -VAUX must be connected. For shielded cables at both inputs, install the W1, W2, W5, and W8 jumpers. Figure 3. Component Location for the EVAL-INAMP-62 UG-261 Evaluation Board User Guide USER OPTIONS Table 4. Jumpers Jumper W1 W2 W3 W4 W5 W6 W7 W8 W9 W10 W11 W12 W13 W14 W15 Function +GUARD select -GUARD select +Input coupling -Input coupling Guard driver -IN -VS to - VAUX +VS to + VAUX Guard driver +IN Guard driver +IN Guard driver +IN Reference input Reference input Reference input In-amp -VS source Guard driver -IN Description Allows the shield of the positive input cable to be connected to the guard driver or ground. Allows the shield of the negative input cable to be connected to the guard driver or ground. Installed; the positive input is dc-coupled. Installed; the negative input is dc-coupled. Connects the negative shield guard driver to Pin 1 of the in-amp. Connects the negative supply voltage to the negative auxiliary voltage of the same value. Connects the positive supply voltage to the positive auxiliary voltage of the same value. Connects the positive shield guard driver to Pin 8 of the in-amp. Connects the positive shield guard driver to ground. Selects the single-shield guard driver. Connects the reference of the in-amp to the offset-adjustable voltage reference. Connects the reference of the in-amp to ground. Connects the reference of the in-amp to an external reference supply. Connects the in-amp -VS pin to GND or to -VS of the evaluation board. Connects the negative shield guard driver to ground. Table 5. Input/Output I/O +VS/-VS GND +IN/-IN +GUARD/-GUARD EXT_REF OUTPUT +VAUX/-VAUX Function Positive and negative rails of the in-amp. Ground for the board. GND1, GND2, GND3, and GND4 designate pins. Positive and negative inputs of the in-amp. Positive and negative terminals for use with a shielded cable. External reference input for the in-amp. Output of the in-amp. Auxiliary power rails for guard drivers and offset reference circuitry. Table 6. User-Supplied Parts for Guard and Offset Circuits Reference Designation Guard Drivers C5, C6 A2 Offset Regulators C7 to C10 A1 CS1, CS2 R9, R10 Part 0.1 F, 25 V ceramic capacitor AD708JN dual precision op amp 0.1 F, 25 V ceramic capacitor OP177 precision op amp J500 240 A current source 5.9 k, 1% metal film resistor Rev. C | Page 6 of 8 Status Not installed Not installed Installed Installed Not installed Not installed Not installed Not installed Not installed Not installed Not installed Installed Not installed Connected to -VS Not installed Evaluation Board User Guide UG-261 QUICK START FOR THE EVAL-INAMP-82RZ AND EVAL-INAMP-82RMZ BOARDS The quick start instructions in this section assume that the evaluation board is in default condition as shown in Table 7. This section describes two separate evaluation boards, where the EVAL-INAMP-82RZ has an SOIC footprint and the EVAL-INAMP-82RMZ has an MSOP footprint. Do not leave the in-amp inputs floating, that is, without a dc return path. This often occurs when the inputs are connected to a transformer, a thermocouple, or a pair of series capacitors. The inputs should have a dc path to ground, as shown in Figure 5 and Figure 6. Table 7. Factory Setting The circuit shown in Figure 6 has series capacitors, C1 and C2, between the signal generator and the input. The series capacitors prevent a dc current from flowing into the input transistors of the instrumentation amplifier. Two matched 10 k resistors are used between the instrumentation amplifier inputs and ground to provide the necessary current path. Closely match these resistors to reduce offset and CMRR errors. Purpose REF is tied to ground. Follow Step 1 through Step 3 to get started using these boards (see Figure 4). 2. 3. Connect a 2.3 V to 15 V supply to +VS and -VS. (Consult the specific data sheet for power supply operating range.) Drive the inputs with a signal. Measure the output on a multimeter or oscilloscope. The output voltage is the voltage measured between VOUT (OUT) and VREF (REF). The output can drive another device, such as an ADC. OSCILLOSCOPE +VS +15V + R1 499 C2 -IN +IN 4 R1 RG 3 RG 2 -IN SMA/SMB CONNECTOR OUT (OPTIONAL) 7 VOUT DUT 5 -VS -VS OUTPUT REF 09753-004 0.1F -VS Figure 4. EVAL-INAMP-82RZ Schematic REFERENCE The reference level of the instrumentation amplifier can be set by driving the REF pin with a precision voltage reference or by using the solder jumper, W1. By default, W1 is soldered, shunting REF to ground. If a reference voltage other than ground is used, the solder must be removed from W1 before driving REF with the reference voltage, as shown in Figure 5. Output measurements should be made by monitoring the voltage between the OUT and REF tie points of the board, as shown in Figure 7. If an external voltage reference is used, the output can be measured, referred to ground, as shown in Figure 5. The evaluation board offers an SMA/SMB outline. By default, the output voltage measured using an SMA/SMB connector is with respect to ground. +VS OSCILLOSCOPE +15V OSCILLOSCOPE 0.1F REF 0V -15V 0.1F -VS - 0.1F 10F OUT W1 10F REF - 10V p-p, 10Hz DUT 5V OUT DUT W1 Figure 7. Correct Output Connection Using the REF Pin 5V -VS 09753-005 -IN R1 5.49k -IN + COM + 10F + COM + 10F +IN 1V p-p, 1kHz 0.1F +IN 500mV p-p, 100Hz +VS 10V -15V 0.1F Figure 6. AC Input Coupling Using a Resistive DC Return Path W1 10F 10k 10F 6 VREF - -IN 1 REF W1 10F 8 +VS + OUT DUT - 10k +IN + COM 10F C1 +IN +VS 0.1F 0.1F 09753-006 1. Figure 5. Using an External Voltage Source to Set the Reference Level (Circled) Input Rev. C | Page 7 of 8 09753-007 Connection W1 is soldered. UG-261 Evaluation Board User Guide NOTES ESD Caution ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality. Legal Terms and Conditions By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the "Evaluation Board"), you are agreeing to be bound by the terms and conditions set forth below ("Agreement") unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you ("Customer") and Analog Devices, Inc. ("ADI"), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term "Third Party" includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED "AS IS" AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER'S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI'S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed. (c)2003-2012 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. UG09753-0-6/12(C) Rev. C | Page 8 of 8 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Analog Devices Inc.: EVAL-INAMP-82RMZ EVAL-INAMP-82RZ EVAL-INAMP-62RZ