ES2A THRU ES2J
Features
Mechanical Data
· For surface applications in order optimize board space
· Low profile package
· Built-in strain relief, ideal for automated placement
· Super fast recovery time
· Plastic package has Unerwrites Laboratory
Flammability Classification 94V-0
· Ideally suited for use in very high frequency switching
power supplies, inverters and as free wheeling diodes
· Low forward voltage drop
· Glass passivated chip junction
· High temperature soldering guaranteed : 250℃/10
seconds, at terminals
Maximum Ratings And Electrical Characteristics
· Case : JEDEC SMB(DO-214AA) molded plastic body
· Terminals : Plated axial lead solderable per
MIL-STD-750, method 2026
· Polarity : Color band denotes cathode end
· Mounting Position : Any
· Weight : 0.003 ounce, 0.093 gram
(Ratings at 25℃ ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive
load. For capacitive load, derate by 20%)
CURRENT 2.0 Amperes
VOLTAGE 50 to 400 Volts
Notes:
(1) Test conditions: IF=0.5A, IR=1.0A, Irr=0.25A.
(2) Measured at 1MHz and applied reverse voltage of 4.0 Volts.
(3) Units mounted on P.C.B 5.0×5.0mm(0.013mm thick) land areas
Maximum recurrent peak reverse voltage
Maximum RMS voltage
Maximum DC blocking voltage
Volts
Peak forward surge current 8.3ms single
half sine-wave superimposed on rated load
(JEDEC method)
V
DC
Maximum average forward rectified current
at T
L
=120℃
Maximum instantaneous forward voltage
at 2.0A
V
RRM
Volts
Symbols Units
0.95V
F
V
RMS
2.0
Amps
Amps
50.0I
FSM
T
J
T
STG
350
-55 to +150 ℃
Volts
Maximum reverse
current at rated voltage
Typical thermal resistance (Note 3)
Operating junction and storage
temperature range
50
ES2A
35
50
5.0
20.0
Volts
μA
℃/W
I
(AV)
I
R
Rθ
JL
T
A
=25℃
T
A
=125℃
100
ES2B
70
100
150
ES2C
105
150
200
ES2D
140
200
400
ES2G
280
400
600
ES2J
420
600
Typical junction capacitance (Note 2) pF18.0
C
J
75.0
Rθ
JA
Maximum reverse recovery time (Note 1) μS35
Trr
1.25
15.0
200
Dimensions in inches and (millimeters)
0.083(2.11)
0.075(1.91)
0.155(3.94)
0.130(3.30)
0.012(0.31)
0.006(0.15)
0.185(4.70)
0.160(4.06)
0.096(2.44)
0.083(2.13)
0.050(1.27)
0.030(0.76)
0.008(0.203)
MAX.
0.220(5.59)
0.200(5.08)
DO-214AA (SMB)
FIG.1-FORWARD CURRENT DERATING CURVE
LEAD TEMPERATURE (
℃)
80 15014013012011010090
RESISTIVE OR INDUCTIVE LOAD
P.C.B. 0.2X0.2"(5.0X5.0mm)
COPPER PAD AREAS
0
1.6
1.2
0.8
0.4
2.4
2.0
AVERAGE FORWARD CURRENT AMPERES
FIG.3-TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS
INSTANTANEOUS FORWARD CURRENT(AMPERES)
10
50
0.1
0.01
1
1.20.4 0.6 1.41.00.8 1.81.6
INSTANTANEOUS FORWARD VOLTAGE (VOLTS)
TJ=25℃
PULSE WIDTH=300
m
S
1% DUTY CYCLE
FIG.5-TYPICAL JUNCTION CAPACITANCE
REVERSE VOLTAGE. VOLTS
JUNCTIOIN CAPACITANCE(pF)
10.1 10010
0
2
4
6
8
10
12
14
TJ=25℃
f=1.0MHz
Vsig=50mVp-P
FIG.6-TYPICAL TRANSIENT THERMAL IMPEDANCE
T, PULSE DURATION ,sec.
0.1 100101
10
1
100
MOUNTED ON
0.2X0.2"(5X7mm)
COPPER PAD AREAS
TRANSIENT THERMAL IMPEDANCE, ℃/W
FIG.4-TYPICAL REVERSE CHARACTERISTICS
PERCENT OF RATED PEAK REVERSE VOLTAGE (%)
INSTANTANEOUS REVERSE CURRENT ,(mA)
0 10080604020
1000
10
1
0.1
0.01
100
TJ=25℃
TJ=75℃
TJ=125℃
FIG.2-MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT
NUMBER OF CYCLES AT 60Hz
PEAK FORWARD SURGE
CURRENT(AMPERES)
1 10010
0
10
15
20
25
30
5
8.3ms SINGLE HALF SINE WAVE
(JEDEC Method) at TL=110℃
RATINGS AND CHARACTERISTIC CURVES ES2A THRU ES2J