Pin Programmable, Precision Voltage Reference AD584 Data Sheet FEATURES PIN CONFIGURATIONS TAB Four programmable output voltages 10.000 V, 7.500 V, 5.000 V, and 2.500 V Laser-trimmed to high accuracies No external components required Trimmed temperature coefficient 15 ppm/C maximum, 0C to 70C (AD584K) 15 ppm/C maximum, -55C to +125C (AD584T) Zero output strobe terminal provided 2-terminal negative reference: capability (5 V and above) Output sources or sinks current Low quiescent current: 1.0 mA maximum 10 mA current output capability MIL-STD-883 compliant versions available 8 10.0V 1 V+ 7 CAP AD584 TOP VIEW (Not to Scale) 2.5V 3 6 VBG 5 STROBE 4 COMMON 00527-001 5.0V 2 10.0V 1 8 V+ 5.0V 2 AD584 7 CAP 2.5V 3 TOP VIEW (Not to Scale) 6 VBG 5 STROBE COMMON 4 00527-002 Figure 1. 8-Pin TO-99 Figure 2. 8-Lead PDIP GENERAL DESCRIPTION The AD584 is an 8-terminal precision voltage reference offering pin programmable selection of four popular output voltages: 10.000 V, 7.500 V, 5.000 V and 2.500 V. Other output voltages, above, below, or between the four standard outputs, are available by the addition of external resistors. The input voltage can vary between 4.5 V and 30 V. The AD584J and AD584K are specified for operation from 0C to +70C, and the AD584S and AD584T are specified for the -55C to +125C range. All grades are packaged in a hermetically sealed, eight-terminal TO-99 metal can, and the AD584J and AD584K are also available in an 8-lead PDIP. Laser wafer trimming (LWT) is used to adjust the pin programmable output levels and temperature coefficients, resulting in the most flexible high precision voltage reference available in monolithic form. 1. In addition to the programmable output voltages, the AD584 offers a unique strobe terminal that permits the device to be turned on or off. When the AD584 is used as a power supply reference, the supply can be switched off with a single, low power signal. In the off state, the current drained by the AD584 is reduced to approximately 100 A. In the on state, the total supply current is typically 750 A, including the output buffer amplifier. The AD584 is recommended for use as a reference for 8-, 10-, or 12-bit digital-to-analog converters (DACs) that require an external precision reference. In addition, the device is ideal for analog-to-digital converters (ADCs) of up to 14-bit accuracy, either successive approximation or integrating designs, and in general, it can offer better performance than that provided by standard self-contained references. PRODUCT HIGHLIGHTS 2. 3. 4. 5. The flexibility of the AD584 eliminates the need to designin and inventory several different voltage references. Furthermore, one AD584 can serve as several references simultaneously when buffered properly. Laser trimming of both initial accuracy and temperature coefficient results in very low errors overtemperature without the use of external components. The AD584 can be operated in a 2-terminal Zener mode at a 5 V output and above. By connecting the input and the output, the AD584 can be used in this Zener configuration as a negative reference. The output of the AD584 is configured to sink or source currents. This means that small reverse currents can be tolerated in circuits using the AD584 without damage to the reference and without disturbing the output voltage (10 V, 7.5 V, and 5 V outputs). The AD584 is available in versions compliant with MIL-STD883. Refer to the Analog Devices current AD584/883B data sheet for detailed specifications. This can be found under the Additional Data Sheets section of the AD584 product page. Rev. C Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 (c)1978-2012 Analog Devices, Inc. All rights reserved. AD584* PRODUCT PAGE QUICK LINKS Last Content Update: 02/23/2017 COMPARABLE PARTS DESIGN RESOURCES View a parametric search of comparable parts. * AD584 Material Declaration * PCN-PDN Information DOCUMENTATION * Quality And Reliability Application Notes * Symbols and Footprints * AN-713: The Effect of Long-Term Drift on Voltage References DISCUSSIONS Data Sheet View all AD584 EngineerZone Discussions. * AD584: Pin Programmable, Precision Voltage Reference Datasheet * AD584: Military Data Sheet SOFTWARE AND SYSTEMS REQUIREMENTS * JAN to Generic Cross Reference TOOLS AND SIMULATIONS * AD584 SPICE Macro-Model SAMPLE AND BUY Visit the product page to see pricing options. TECHNICAL SUPPORT Submit a technical question or find your regional support number. DOCUMENT FEEDBACK Submit feedback for this data sheet. This page is dynamically generated by Analog Devices, Inc., and inserted into this data sheet. A dynamic change to the content on this page will not trigger a change to either the revision number or the content of the product data sheet. This dynamic page may be frequently modified. AD584 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Output Current Characteristics...................................................7 Pin Configurations ........................................................................... 1 Dynamic Performance ..................................................................7 General Description ......................................................................... 1 Noise Filtering ...............................................................................8 Product Highlights ........................................................................... 1 Using the Strobe Terminal ...........................................................8 Revision History ............................................................................... 2 Percision High Current Supply....................................................8 Specifications..................................................................................... 3 The AD584 as a Current Limiter.................................................9 Absolute Maximum Ratings ............................................................ 5 Negative Reference Voltages from an AD584 ...............................9 ESD Caution .................................................................................. 5 10 V Reference with Multiplying CMOS DACs or ADCs .......9 Theory of Operation ........................................................................ 6 Precision DAC Reference .......................................................... 10 Applying the AD584 .................................................................... 6 Outline Dimensions ....................................................................... 11 Performance over Temperature .................................................. 7 Ordering Guide .......................................................................... 12 REVISION HISTORY 5/12--Rev. B to Rev. C Deleted AD584L ................................................................. Universal Changes to Features Section, General Description Section and Product Highlights Section ............................................................. 1 Deleted Metalization Photograph .................................................. 4 Changes to 10 V Reference with Multiplying CMOS DACs or ADCs Section .................................................................................... 9 Changes to Precision DAC Reference Section and Figure 19... 10 Updated Outline Dimensions ....................................................... 11 Changes to Ordering Guide .......................................................... 12 7/01--Rev. A to Rev. B Rev. C | Page 2 of 12 Data Sheet AD584 SPECIFICATIONS VIN = 15 V and 25C, unless otherwise noted. Specifications shown in boldface are tested on all production units at final electrical test. Results from those tests are used to calculate outgoing quality levels. All minimum and maximum specifications are guaranteed; although, only those shown in boldface are tested on all production units. Table 1. Model OUTPUT VOLTAGE TOLERANCE Maximum Error at Pin 1 for Nominal Outputs of 10.000 V 7.500 V 5.000 V 2.500 V OUTPUT VOLTAGE CHANGE Maximum Deviation from 25C Value, TMIN to TMAX 1 10.000 V, 7.500 V, and 5.000 V Outputs 2.500 V Output Differential Temperature Coefficients Between Outputs QUIESCENT CURRENT Temperature Variation TURN-ON SETTLING TIME TO 0.1% NOISE (0.1 Hz TO 10 Hz) LONG-TERM STABILITY SHORT-CIRCUIT CURRENT LINE REGULATION (NO LOAD) 15 V VIN 30 V (VOUT + 2.5 V) VIN 15 V LOAD REGULATION 0 IOUT 5 mA, All Outputs OUTPUT CURRENT VIN VOUT + 2.5 V Source at 25C Source TMIN to TMAX Sink TMIN to TMAX TEMPERATURE RANGE Operating Storage PACKAGE OPTION 8-Pin Metal Header (TO-99, H-08) 8-Lead Plastic Dual In-Line Package (PDIP, N-8) 1 Min AD584J Typ 5 0.75 1.5 200 50 25 30 Max Min AD584K Typ Max Unit 30 20 15 7.5 10 8 6 3.5 mV mV mV mV 30 30 15 15 ppm/C ppm/C ppm/C mA A/C s V p-p ppm/1000 Hrs mA 3 0.75 1.5 200 50 25 30 1.0 0.002 0.005 20 50 10 5 5 20 1.0 0.002 0.005 %/V %/V 50 ppm/mA 10 5 5 0 -65 70 +175 AD584JH AD584JN Calculated as average over the operating temperature range. Rev. C | Page 3 of 12 mA mA mA 0 -65 70 +175 AD584KH AD584KN C C AD584 Data Sheet Specifications shown in boldface are tested on all production units at final electrical test. Results from those tests are used to calculate outgoing quality levels. All minimum and maximum specifications are guaranteed; although, only those shown in boldface are tested on all production units. Table 2. Model OUTPUT VOLTAGE TOLERANCE Maximum Error at Pin 1 for Nominal Outputs of 10.000 V 7.500 V 5.000 V 2.500 V OUTPUT VOLTAGE CHANGE Maximum Deviation from 25C Value, TMIN to TMAX 1 10.000 V, 7.500 V, and 5.000 V Outputs 2.500 V Output Differential Temperature Coefficients Between Outputs QUIESCENT CURRENT Temperature Variation TURN-ON SETTLING TIME TO 0.1% NOISE (0.1 Hz TO 10 Hz) LONG-TERM STABILITY SHORT-CIRCUIT CURRENT LINE REGULATION (NO LOAD) 15 V VIN 30 V (VOUT + 2.5 V) VIN 15 V LOAD REGULATION 0 IOUT 5 mA, All Outputs OUTPUT CURRENT VIN VOUT + 2.5 V Source at 25C Source TMIN to TMAX Sink TMIN to TMAX TEMPERATURE RANGE Operating Storage PACKAGE OPTION 8-Pin Metal Header (TO-99, H-08) 1 Min AD584S Typ 5 0.75 1.5 200 50 25 30 Max Min AD584T Typ Max Unit 30 20 15 7.5 10 8 6 3.5 mV mV mV mV 30 30 15 20 ppm/C ppm/C ppm/C mA A/C s V p-p ppm/1000 Hrs mA 3 0.75 1.5 200 50 25 30 1.0 0.002 0.005 20 50 10 5 5 20 1.0 0.002 0.005 %/V %/V 50 ppm/mA 10 5 5 -55 -65 +125 +175 AD584SH Calculated as average over the operating temperature range. Rev. C | Page 4 of 12 mA mA mA -55 -65 +125 +175 AD584TH C C Data Sheet AD584 ABSOLUTE MAXIMUM RATINGS ESD CAUTION Table 3. Parameter Input Voltage VIN to Ground Power Dissipation at 25C Operating Junction Temperature Range Lead Temperature (Soldering 10 sec) Thermal Resistance Junction-to-Ambient (H-08A) Rating 40 V 600 mW -55C to +125C 300C 150C/W Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Rev. C | Page 5 of 12 AD584 Data Sheet THEORY OF OPERATION APPLYING THE AD584 With power applied to Pin 8 and Pin 4 and all other pins open, the AD584 produces a buffered nominal 10.0 V output between Pin 1 and Pin 4 (see Figure 3). The stabilized output voltage can be reduced to 7.5 V, 5.0 V, or 2.5 V by connecting the programming pins as shown in Table 4. Table 4. Pin Programming Join the 2.5 V (Pin 3) and 5.0 V (Pin 2) pins. Connect the 5.0 V pin (Pin 2) to the output pin (Pin 1). Connect the 2.5 V pin (Pin 3) to the output pin (Pin 1). The options shown in Table 4 are available without the use of any additional components. Multiple outputs using only one AD584 can be provided by buffering each voltage programming pin with a unity-gain, noninverting op amp. VSUPPLY 8 AD584 VOUT 10V 24k 1 R4 5V * 12k 2 When only small adjustments or trims are required, the circuit in Figure 4 offers better resolution over a limited trim range. The circuit can be programmed to 5.0 V, 7.5 V, or 10 V, and it can be adjusted by means of R1 over a range of about 200 mV. To trim the 2.5 V output option, R2 (see Figure 4) can be reconnected to the band gap reference (Pin 6). In this configuration, limit the adjustment to 100 mV to avoid affecting the performance of the AD584. V+ 2.5V R1 3 VBG 6k 8 VOUT 1 R3 6 R2 2 6k AD584 3 COMMON 4 * THE 2.5V TAP IS USED INTERNALLY AS A BIAS POINT AND SHOULD NOT BE CHANGED BY MORE THAN 100mV IN ANY TRIM CONFIGURATION. 00527-004 6 10.0V 5.0V R2 300k 2.5V R1 10k VBG 4 COMMON Figure 3. Variable Output Options The AD584 can also be programmed over a wide range of output voltages, including voltages greater than 10 V, by the addition of one or more external resistors. Figure 3 illustrates the general adjustment procedure, with approximate values given for the internal resistors of the AD584. The AD584 may be modeled as an op amp with a noninverting feedback connection, driven by a high stability 1.215 V band gap reference (see Figure 5 for schematic). When the feedback ratio is adjusted with external resistors, the output amplifier can be made to multiply the reference voltage by almost any convenient amount, making popular outputs of 10.24 V, 5.12 V, 2.56 V, or 6.3 V easy to obtain. The most general adjustment (which gives the greatest range and poorest resolution) uses R1 and R2 alone (see Figure 3). As R1 is adjusted to its upper limit, the 2.5V pin (Pin 3) is connected to the output, which reduces to 2.5 V. As R1 is adjusted to its lower limit, the output voltage rises to a value limited by R2. For example, if R2 is approximately 6 k, the upper limit of the output range is Figure 4. Output Trimming V+ R40 R41 Q7 Q20 Q10 STROBE Q8 Q11 C52 Q12 R42 Q15 OUT 10V C51 Q6 R34 Q14 5V TAP R37 Q5 Q13 Q16 2.5V TAP R35 SUB C50 R33 R32 CAP Rev. C | Page 6 of 12 Q3 Q4 Q2 R38 R30 R39 R31 VBG Q1 R36 V- Figure 5. Schematic Diagram 00527-006 1.215V Alternatively, the output voltage can be raised by loading the 2.5 V tap with R3 alone. The output voltage can be lowered by connecting R4 alone. Either of these resistors can be a fixed resistor selected by test or an adjustable resistor. In all cases, the resistors should have a low temperature coefficient to match the AD584 internal resistors, which have a negative temperature coefficient less than 60 ppm/C. If both R3 and R4 are used, these resistors should have matching temperature coefficients. 00527-005 Output Voltage (V) 7.5 5.0 2.5 approximately 20 V, even for the large values of R1. Do not omit R2; choose its value to limit the output to a value that can be tolerated by the load circuits. If R2 is zero, adjusting R1 to its lower limit results in a loss of control over the output voltage. When precision voltages are set at levels other than the standard outputs, account for the 20% absolute tolerance in the internal resistor ladder. Data Sheet AD584 PERFORMANCE OVER TEMPERATURE supply or ground. Figure 7 shows the output voltage vs. the output current characteristics of the device. Source current is displayed as negative current in the figure, and sink current is displayed as positive current. The short-circuit current (that is, 0 V output) is about 28 mA; however, when shorted to 15 V, the sink current goes to approximately 20 mA. Each AD584 is tested at three temperatures over the -55C to +125C range to ensure that each device falls within the maximum error band (see Figure 6) specified for a particular grade (that is, S and T grades); three-point measurement guarantees performance within the error band from 0C to 70C (that is, J and K grades). The error band guaranteed for the AD584 is the maximum deviation from the initial value at 25C. Thus, given the grade of the AD584, the maximum total error from the initial tolerance plus the temperature variation can easily be determined. For example, for the AD584T, the initial tolerance is 10 mV, and the error band is 15 mV. Therefore, the unit is guaranteed to be 10.000 V 25 mV from -55C to +125C. OUTPUT VOLTAGE (V) 14 10.005 +VS = 15V TA = 25C 12 10 8 6 4 2 -20 10.000 -15 -10 -5 0 5 10 15 SOURCE SINK OUTPUT CURRENT (mA) 20 00527-008 VOUT (V) 0 Figure 7. Output Voltage vs. Output Current (Sink and Source) DYNAMIC PERFORMANCE 25 70 125 TEMPERATURE (C) Figure 6. Typical Temperature Characteristic OUTPUT CURRENT CHARACTERISTICS The AD584 has the capability to either source or sink current and provide good load regulation in either direction; although, it has better characteristics in the source mode (positive current into the load). The circuit is protected for shorts to either positive 12V 10.03V OUTPUT 10.02V 11V OUTPUT 10.01V 10.00V 10V 20V POWER SUPPLY INPUT 10V 0V 0 50 100 150 200 250 SETTLING TIME (s) Figure 8. Output Settling Characteristic Rev. C | Page 7 of 12 00527-009 0 00527-007 9.995 -55 Many low power instrument manufacturers are becoming increasingly concerned with the turn-on characteristics of the components being used in their systems. Fast turn-on components often enable the end user to keep power off when not needed and yet respond quickly when the power is turned on. Figure 8 displays the turn-on characteristic of the AD584. Figure 8 is generated from cold-start operation and represents the true turn-on waveform after an extended period with the supplies off. Figure 8 shows both the coarse and fine transient characteristics of the device; the total settling time to within 10 mV is about 180 s, and there is no long thermal tail appearing after the point. AD584 Data Sheet NOISE FILTERING USING THE STROBE TERMINAL The bandwidth of the output amplifier in the AD584 can be reduced to filter output noise. A capacitor ranging between 0.01 F and 0.1 F connected between the CAP and VBG terminals further reduces the wideband and feedthrough noise in the output of the AD584, as shown in Figure 9 and Figure 10. However, this tends to increase the turn-on settling time of the device; therefore, allow for ample warm-up time. The AD584 has a strobe input that can be used to zero the output. This unique feature permits a variety of new applications in signal and power conditioning circuits. SUPPLY V+ 8 7 1 10.0V AD584 VBG 6 V+ 4 8 00527-010 COMMON STROBE *INCREASES TURN-ON TIME 5 100 1 AD584 Figure 9. Additional Noise Filtering with an External Capacitor 1000 NO CAP 1000pF NO CAP TOTAL NOISE (V rms) UP TO SPECIFIED FREQUENCY 1k 2N2222 10k 4 COMMON 10k FREQUENCY (Hz) 100k PERCISION HIGH CURRENT SUPPLY 1M 00527-011 100 LO = ON 20k The strobe terminal tolerates up to 5 A leakage, and its driver should be capable of sinking 500 A continuous. A low leakage, open collector gate can be used to drive the strobe terminal directly, provided the gate can withstand the AD584 output voltage plus 1 V. 0.01F 1 10 HI = OFF Figure 11. Use of the Strobe Terminal 100 10 2 3 LOGIC INPUT NOISE SPECTRAL DENSITY (nV/ Hz) 100pF 10.0V 00527-012 0.01F* TO 0.1F Figure 10. Spectral Noise Density and Total RMS Noise vs. Frequency The AD584 can be easily connected to a power PNP or power PNP Darlington device to provide much greater output current capability. The circuit shown in Figure 12 delivers a precision 10 V output with up to 4 A supplied to the load. If the load has a significant capacitive component, the 0.1 F capacitor is required. If the load is purely resistive, improved high frequency, supply rejection results from removing the capacitor. VIN 15V 470 2N6040 V+ 0.1F 8 AD584 10.0V 1 VOUT 10V @ 4A 4 COMMON Figure 12. High Current Precision Supply Rev. C | Page 8 of 12 00527-013 CAP Figure 11 illustrates the strobe connection. A simple NPN switch can be used to translate a TTL logic signal into a strobe of the output. The AD584 operates normally when there is no current drawn from Pin 5. Bringing this terminal low, to less than 200 mV, allows the output voltage to go to zero. In this mode, the AD584 is not required to source or sink current (unless a 0.7 V residual output is permissible). If the AD584 is required to sink a transient current while strobe is off, limit the strobe terminal input current by a 100 resistor, as shown in Figure 11. Data Sheet AD584 The AD584 can also use an NPN or NPN Darlington transistor to boost its output current. Simply connect the 10 V output terminal of the AD584 to the base of the NPN booster and take the output from the booster emitter, as shown in Figure 13. The 5.0V pin or the 2.5V pin must connect to the actual output in this configuration. Variable or adjustable outputs (as shown in Figure 3 and Figure 4) can be combined with a 5.0 V connection to obtain outputs above 5.0 V. The temperature characteristics and long-term stability of the device is essentially the same as that of a unit used in standard 3-terminal mode. ANALOG GND V+ 8 1 1F AD584 2 VOUT 5.0V TAP RAW SUPPLY (5V > VOUT) 4 VREF -5V COMMON DARLINGTON NPN 2N6057 -15V V+ 8 Figure 15. 2-Terminal, -5 V Reference 10.0V VOUT (5V, 12A AS SHOWN) 2.5V 3 1k 4 COMMON Figure 13. NPN Output Current Booster THE AD584 AS A CURRENT LIMITER The AD584 represents an alternative to current limiter diodes that require factory selection to achieve a desired current. Use of current limiting diodes often results in temperature coefficients of 1%/C. Use of the AD584 in this mode is not limited to a set current limit; it can be programmed from 0.75 mA to 5 mA with the insertion of a single external resistor (see Figure 14). The minimum voltage required to drive the connection is 5 V. V+ 8 1 AD584 3 VOUT = 2.5V = 2.5V TAP i 2.5V + 0.75mA R COMMON 00527-015 RLOAD 4 The AD584 can also be used in 2-terminal mode to develop a positive reference. VIN and VOUT are tied together and to the positive supply through an appropriate supply resistor. The performance characteristics are similar to those of a negative 2-terminal connection. The only advantage of this connection over the standard 3-terminal connection is that a lower primary supply can be used, as low as 0.5 V above the desired output voltage. This type of operation requires considerable attention to load and to the primary supply regulation to ensure that the AD584 always remains within its regulating range of 1 mA to 5 mA (2 mA to 5 mA for operation beyond 85C). 10 V REFERENCE WITH MULTIPLYING CMOS DACs OR ADCs The AD584 is ideal for application with the AD7533 10-bit multiplying CMOS DAC, especially for low power applications. It is equally suitable for the AD7574 8-bit ADC. In the standard hook-up, as shown in Figure 16, the standard output voltages are inverted by the amplifier/DAC configuration to produce converted voltage ranges. For example, a +10 V reference produces a 0 V to -10 V range. If an OP1177 amplifier is used, total quiescent supply current is typically 2 mA. +15V Figure 14. A Two-Component Precision Current Limiter NEGATIVE REFERENCE VOLTAGES FROM AN AD584 The AD584 can also be used in a 2-terminal Zener mode to provide a precision -10 V, -7.5 V, or -5.0 V reference. As shown in Figure 15, the VIN and VOUT terminals are connected together to the positive supply (in this case, ground). The AD584 COMMON pin is connected through a resistor to the negative supply. The output is now taken from the COMMON pin instead of VOUT. With 1 mA flowing through the AD584 in this mode, a typical unit shows a 2 mV increase in the output level over that produced in 3-terminal mode. Also, note that the effective output impedance in this connection increases from 0.2 typical to 2 . It is essential to arrange the output load and the supply resistor, RS, so that the net current through the AD584 is always between 1 mA and 5 mA (between 2 mA and 5 mA for operation beyond 85C). 8 V+ AD584 1 10.0V 4 COMMON VREF 15 BIT 1 (MSB) DIGITAL INPUT Rev. C | Page 9 of 12 14 16 4 +15V 5 AD7533 1 13 BIT 10 (LSB) RFB 3 2 IOUT1 IOUT2 VOUT 0V TO -10V -15V COMMON Figure 16. Low Power 10-Bit CMOS DAC Application 00527-017 5.0V 2 00527-014 1 AD584 00527-016 RS 2.4k 5% AD584 Data Sheet The AD584 is normally used in the -10 V mode with the AD7574 to give a 0 V to +10 V ADC range. This is shown in Figure 17. Bipolar output applications and other operating details can be found in the data sheets for the CMOS products. -15V 8 4 COMMON GAIN TRIM R2 2k* -10V REF 1 10.0V 0.1F SIGNAL INPUT 0V TO +10V R1 2k 10%* 1 AD7574 2 (TOP VIEW) 18 DIGITAL SUPPLY RETURN 3 4 V+ V+ 5 00527-019 GROUND INTERTIE ANALOG GROUND * R1 AND R2 CAN BE OMITTED IF GAIN TRIM IS NOT REQUIRED. 13 5 14 6 15 7 AD 8 DAC08 9 10 11 4 12 16 1 2 3 A1 (MSB) A2 A3 A4 A5 A6 A7 A8 (LSB) COMP Figure 17. AD584 as -10 V Reference for CMOS ADC PRECISION DAC REFERENCE The AD565A, like many DACs, can operate with an external 10 V reference element (see Figure 19). This 10 V reference voltage is converted into a reference current of approximately 0.5 mA via the internal 19.95 k resistor (in series with the external 100 trimmer). The gain temperature coefficient of the AD565A is primarily governed by the temperature tracking of the 19.95 k resistor and the 5 k/10 k span resistors; this gain temperature coefficient is guaranteed to 3 ppm/C. Therefore, using the AD584K (at 5 ppm/C) as the 10 V reference guarantees a maximum full- VREF (+) VREF (-) 10.0V R14 AD584 R15 3 2.5V R14 = R15 COMMON IO VLC C V- IOUT Figure 18. Current Output, 8-Bit Digital-to-Analog Configuration +15V 0.1F REF OUT VCC BIPOLAR OFF +15V 20V SPAN AD584 1 GAIN ADJUST REF 15T IN R2 100 4 REF GND AD565A 10V 19.95k 5k 9.95k 0.5mA 10V SPAN 5k IREF DAC 20k IOUT = 4 x IREF x CODE POWER GND MSB +15V 2 6 IO 8k 3 OP1177 OP AMP OUTPUT 10V -15V CODE INPUT -VEE DAC OUT LSB 00527-018 8 4 RL BIPOLAR OFFSET ADJUST 15T R1 100 8 1 00527-020 AD584 V+ +15V R3 1.2k 5% scale temperature coefficient of 18 ppm/C more than the commercial range. The 10 V reference also supplies the normal 1 mA bipolar offset current through the 9.95 k bipolar offset resistor. The bipolar offset temperature coefficient thus depends only on the temperature coefficient matching of the bipolar offset resistor to the input reference resistor and is guaranteed to 3 ppm/C. Figure 18 demonstrates the flexibility of the AD584 applied to another popular digital-to-analog configuration. 0.1F -15V Figure 19. Precision 12-Bit DAC Rev. C | Page 10 of 12 Data Sheet AD584 OUTLINE DIMENSIONS REFERENCE PLANE 0.1850 (4.70) 0.1650 (4.19) 0.5000 (12.70) MIN 0.2500 (6.35) MIN 0.0500 (1.27) MAX 0.1000 (2.54) BSC 0.1600 (4.06) 0.1400 (3.56) 0.3350 (8.51) 0.3050 (7.75) 0.3700 (9.40) 0.3350 (8.51) 5 6 4 0.2000 (5.08) BSC 3 7 2 0.0400 (1.02) MAX 0.1000 (2.54) BSC 0.0190 (0.48) 0.0160 (0.41) 0.0210 (0.53) 0.0160 (0.41) 0.0400 (1.02) 0.0100 (0.25) 8 0.0450 (1.14) 0.0270 (0.69) 1 0.0340 (0.86) 0.0280 (0.71) 45 BSC COMPLIANT TO JEDEC STANDARDS MO-002-AK CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. 022306-A BASE & SEATING PLANE Figure 20. 8-Pin Metal Header [TO-99] (H-08) Dimensions shown in inches and (millimeters) 0.400 (10.16) 0.365 (9.27) 0.355 (9.02) 8 5 1 4 0.280 (7.11) 0.250 (6.35) 0.240 (6.10) 0.100 (2.54) BSC 0.060 (1.52) MAX 0.210 (5.33) MAX 0.015 (0.38) MIN 0.150 (3.81) 0.130 (3.30) 0.115 (2.92) SEATING PLANE 0.022 (0.56) 0.018 (0.46) 0.014 (0.36) 0.325 (8.26) 0.310 (7.87) 0.300 (7.62) 0.195 (4.95) 0.130 (3.30) 0.115 (2.92) 0.015 (0.38) GAUGE PLANE 0.005 (0.13) MIN 0.014 (0.36) 0.010 (0.25) 0.008 (0.20) 0.430 (10.92) MAX COMPLIANT TO JEDEC STANDARDS MS-001 CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. CORNER LEADS MAY BE CONFIGURED AS WHOLE OR HALF LEADS. Figure 21. 8-Lead Plastic Dual In-Line Package [PDIP] Narrow Body (N-8) Dimensions shown in inches and (millimeters) Rev. C | Page 11 of 12 070606-A 0.070 (1.78) 0.060 (1.52) 0.045 (1.14) AD584 Data Sheet ORDERING GUIDE Model 1 AD584JH AD584JNZ AD584KH AD584KNZ AD584SH AD584SH/883B AD584TH AD584TH/883B AD584JH AD584JNZ AD584KH AD584KNZ AD584SH AD584SH/883B AD584TH AD584TH/883B AD584JH AD584JNZ AD584KH AD584KNZ AD584SH AD584SH/883B AD584TH AD584TH/883B AD584JH AD584JNZ AD584KH AD584KNZ AD584SH AD584SH/883B AD584TH AD584TH/883B 1 Output Voltage (VO) 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 Initial Accuracy mV % 7.5 0.30 7.5 0.30 3.5 0.14 3.5 0.14 7.5 0.30 7.5 0.30 3.5 0.14 3.5 0.14 15.0 0.30 15.0 0.30 6.0 0.12 6.0 0.12 15.0 0.14 15.0 0.30 6.0 0.30 6.0 0.12 20.0 0.27 20.0 0.27 8.0 0.11 8.0 0.11 20.0 0.27 20.0 0.27 8.0 0.11 8.0 0.11 30.0 0.30 30.0 0.30 10.0 0.10 10.0 0.10 30.0 0.30 30.0 0.30 10.0 0.10 10.0 0.10 Temperature Coefficient (ppm/C) 30 30 15 15 30 30 20 20 30 30 15 15 30 30 15 15 30 30 15 15 30 30 15 15 30 30 15 15 30 30 15 15 Z = RoHS Compliant Part. (c)1978-2012 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D00527-0-5/12(C) Rev. C | Page 12 of 12 Temperature Range (C) 0 to 70 0 to 70 0 to 70 0 to 70 -55 to +125 -55 to +125 -55 to +125 -55 to +125 0 to 70 0 to 70 0 to 70 0 to 70 -55 to +125 -55 to +125 -55 to +125 -55 to +125 0 to 70 0 to 70 0 to 70 0 to 70 -55 to +125 -55 to +125 -55 to +125 -55 to +125 0 to 70 0 to 70 0 to 70 0 to 70 -55 to +125 -55 to +125 -55 to +125 -55 to +125 Package Description 8-Pin TO-99 8-Lead PDIP 8-Pin TO-99 8-Lead PDIP 8-Pin TO-99 8-Pin TO-99 8-Pin TO-99 8-Pin TO-99 8-Pin TO-99 8-Lead PDIP 8-Pin TO-99 8-Lead PDIP 8-Pin TO-99 8-Pin TO-99 8-Pin TO-99 8-Pin TO-99 8-Pin TO-99 8-Lead PDIP 8-Pin TO-99 8-Lead PDIP 8-Pin TO-99 8-Pin TO-99 8-Pin TO-99 8-Pin TO-99 8-Pin TO-99 8-Lead PDIP 8-Pin TO-99 8-Lead PDIP 8-Pin TO-99 8-Pin TO-99 8-Pin TO-99 8-Pin TO-99 Package Option H-08 N-8 H-08 N-8 H-08 H-08 H-08 H-08 H-08 N-8 H-08 N-8 H-08 H-08 H-08 H-08 H-08 N-8 H-08 N-8 H-08 H-08 H-08 H-08 H-08 N-8 H-08 N-8 H-08 H-08 H-08 H-08 Ordering Quantity 100 50 100 50 100 100 100 100 100 50 100 50 100 100 100 100 100 50 100 50 100 100 100 100 100 50 100 50 100 100 100 100