DMF-5001NYL-SEB-AVE-BDN - Optrex - Datasheet.Directory

DMF5001NYJ-LY-AQE-AZ (AZ) No. 2001-0245 OPTREX CORPORATION Page 1/17

LCD Module Technical Specification

DMF5001NYJ-LY-AQE-AZ

Table of Contents

1. General Specifications..................................................................................................................................2

2. Electrical Specifications...............................................................................................................................3

3. Optical Specifications...................................................................................................................................7

4. I/O Terminal......................................................................................................................................................9

5. Test...................................................................................................................................................................11

6. Appearance Standards ...............................................................................................................................12

7. Code System of Production Lot...............................................................................................................15

8. Type Number..................................................................................................................................................15

9. Applying Precautions ..................................................................................................................................15

10. Precautions Relating Product Handling................................................................................................16

11. Warranty........................................................................................................................................................17

Checked by (Design Engineering Div.)

Checked by (Quality Assurance Div.)

Approved by (Production Div.)

Prepared by (Production Div.)

Revision History

Rev. Date Page Comment

Type No.

Nov 7, 2001

OPTREX

First Edition

Final Revision

******

DMF5001NYJ-LY-AQE-AZ (AZ) No. 2001-0245 OPTREX CORPORATION Page 2/17

1. General Specifications

Operating Temp. :min. -10°C ~max. 60°C

Storage Temp. :min. -20°C ~max. 70°C

Dot Pixels :160 (W) × 128 (H) dots

Dot Size :0.54 (W) × 0.54 (H) mm

Dot Pitch :0.58 (W) × 0.58 (H) mm

Viewing Area :101.0 (W) × 82.0 (H) mm

Outline Dimensions :129.0 (W) × 102.0 (H) × 19.2max. (D) mm

Weight :190g max.

LCD Type :NTD-7353

( STN / Yellow-mode / Transmissive )

Viewing Angle :6:00

Control LSI :T6963C-0101 (Produced by TOSHIBA)

Data Transfer :8 bit parallel data transfer

Backlight :LED Backlight / Yellow-green

Drawings :Dimensional Outline UE-34487A

DMF5001NYJ-LY-AQE-AZ (AZ) No. 2001-0245 OPTREX CORPORATION Page 3/17

2. Electrical Specifications

2.1. Absolute Maximum Ratings VSS=0V

Parameter Symbol Conditions Min. Max. Units

Supply Voltage

(Logic)

VDD-VSS --0.3 7.0 V

Supply Voltage

(LCD Drive)

VDD-VEE --0.3 28.0 V

Input Voltage VI--0.3 VDD+0.3 V

2.2. DC Characteristics Ta=25°C, VSS=0V

Parameter Symbol Conditions Min. Typ. Max. Units

Supply Voltage

(Logic)

VDD-VSS -4.5 -5.5 V

VDD-VEE -23.0 -26.0 V

Supply Voltage

(LCD Drive) VDD-VCONT Shown in 3.1 V

High Level

Input Voltage

VIH VDD=5.0V±10% VDD-2.2 -VDD V

Low Level

Input Voltage

VIL VDD=5.0V±10% 0-0.8 V

High Level

Output Voltage

VOH IOH=-0.75mA VDD-0.3 -VDD V

Low Level

Output Voltage

VOL IOL=0.75mA 0-0.3 V

Supply Current

IDD VDD-VSS=5.0V -13.4 30.0 mA

IEE VDD-VEE=19.3V-3.7 20.0 mA

DMF5001NYJ-LY-AQE-AZ (AZ) No. 2001-0245 OPTREX CORPORATION Page 4/17

2.3. AC Characteristics VDD=5.0V±10%

Parameter Symbol Min. Max. Units

C/D Setup Time tCDS 100 -ns

C/D Hold Time tCDH 10 -ns

CE, RD, WR Pulse Width tCE, tRD, tWR 80 -ns

Data Setup Time tDS 80 -ns

Data Hold Time tDH 40 -ns

Access Time tACC -150 ns

Output Hold Time tOH 10 50 ns

(WRITE)

(READ)

RD, WR

D0∼D7

C/D

D0∼D7

tDS

tOH

tDH

tACC

tCE,tRD,tWR

tCDHtCDS

DMF5001NYJ-LY-AQE-AZ (AZ) No. 2001-0245 OPTREX CORPORATION Page 5/17

2.4. Power Supply ON/OFF Sequence

2.4.1. ON Sequence

2.4.2. OFF Sequence

2.4.3. Reset Sequence

Please maintain the above sequence when turning on and off the power supply of the

module.

If VEE and/or VCONT is supplied to the module while internal alternate signal for LCD

driving (M) is unstable or RESET is active, DC component will be supplied to the LCD

panel. This may cause damage to the LCD module.

RESET

VDD

VCONT

SIGNAL

T≥0

T≥0T≥0T≥50msT≥50ms

T>250µs

LEVEL

L Level

H Level

VDD

VCONT

VDD

VSS

Power OffPower On Reset CancellationReset

T≥10 ms

HALT

VEE

VSS

VDD

VSS

VDD

VEE

0≤t

SIGNAL

0≤t

SIGNAL

VDD

LEVEL

VCONT

(Without RESET and)

HALT Signal)

VEE

VSS

VDD

VSS

VDD

VEE

0≤t

SIGNAL

0≤t

SIGNAL

VDD

LEVEL

VCONT

(Without RESET and

HALT Signal)

DMF5001NYJ-LY-AQE-AZ (AZ) No. 2001-0245 OPTREX CORPORATION Page 6/17

2.5. Lighting Specifications

2.5.1. Absolute Maximum Ratings Ta=25°C

Parameter Symbol Conditions Min. Typ. Max. Units

Foward Current IFNote 1 - - 1300 mA

Reverse Voltage VR- - - 8V

LED Power Dissipation PD- - - 5.7 W

Note 1 : Refer to the foward current derating curve.

2.5.2. Operating Characteristics Ta=25°C

Parameter Symbol Conditions Min. Typ. Max. Units

Foward Voltage VFIF=650mA 3.7 4.1 4.4 V

Luminance of

Backlight Surface

LIF=650mA 40 - - cd/m2

6025-10Ta (

679

1300

IF (mA)

DMF5001NYJ-LY-AQE-AZ (AZ) No. 2001-0245 OPTREX CORPORATION Page 7/17

3. Optical Specifications

3.1. LCD Driving Voltage

Parameter Symbol Conditions Min. Typ. Max. Units

Recommended Ta= -10°C- - 21.5 V

LCD Driving Voltage VDD-VCONT Ta=25°C18.0 19.3 20.6 V

Note 1 Ta=60°C16.3 - - V

Note 1 : Voltage (Applied actual waveform to LCD Module) for the best contrast. The range of

minimum and maximum shows tolerance of the operating voltage. The specified contrast

ratio and response time are not guaranteed over the entire range.

3.2. Optical Characteristics Ta=25°C, 1/128 Duty, 1/12.3 Bias, VD=18.7V (Note 4), θ= 0°, φ= - °

Parameter Symbol Conditions Min. Typ. Max. Units

Contrast Ratio Note 1 CR θ= 0°, φ= - °-6-

Viewing Angle Shown in 3.3

Response Rise Note 2 TON - - 180 270 ms

Time Decay Note 3 TOFF - - 240 360 ms

Note 1 :Contrast ratio is definded as follows. (CR = LOFF / LON)

LON :Luminance of the ON segments

LOFF :Luminance of the OFF segments

Note 2 :The time that the luminance level reaches 90% of the saturation level from 0%

when ON signal is applied.

Note 3 :The time that the luminance level reaches 10% of the saturation level from 100%

when OFF signal is applied.

Note 4 :Definition of Driving Voltage VD

VD=VDD-VCONT-VBE

Assuming that the typical driving waveforms shown below are applied to the LCD

Panel at 1/A Duty - 1/B Bias ( A : Duty Number, B : Bias Number ). Driving voltage

VD is definded as follows.

VD = (Vth1+Vth2) / 2

Vth1 : The voltage VO-P that should provide 50% of the saturation level in the

luminance at the segment which the ON signal is applied to.

Vth2 : The voltage VO-P that should provide 50% of the saturation level in the

luminance at the segment which the OFF signal is applied to.

O-P

1 / f

( B-2 )×VO-P / B

1 / ( fF×A )

DMF5001NYJ-LY-AQE-AZ (AZ) No. 2001-0245 OPTREX CORPORATION Page 8/17

3.3. Definition of Viewing Angle and Optimum Viewing Area

*Point • shows the point where contrast ratio is measured. : θ= 0°, φ= -°

*Driving condition : 1/128 Duty, 1/12.3 Bias, VD=18.7V, fF=70Hz

270°

180°

270°

135°

315°225°

45°

180°

90°

(φ = 0°)

*Area shows typ. CR≥2

3.4. System Block Diagram

Halogen bulb

Computer

Rotation Table ( θ,φ )

Temperature Chamber

LCD

Optical Fiber

Waveform Generator

Control Unit &

#1980A WB

Photometer φ

DMF5001NYJ-LY-AQE-AZ (AZ) No. 2001-0245 OPTREX CORPORATION Page 9/17

4. I/O Terminal

4.1. Pin Assignment

No. Symbol Level Function

1FG −Frame Ground

2VSS -Power Supply (0V, GND)

3VDD -Power Supply for Logic

4VCONT -Voltage Level for LCD Contrast Adjustment

5VEE -Power Supply for LCD Drive

6WR H / L Write Signal L : Active

7RD H / L Read Signal L : Active

8CE H / L Chip Enable Signal L : Active

9C/D H / L Write Mode H : Command Write L : Data Write

Read Mode H : Status Read L : Data Read

10 HALT H / L Clock Operating Stop Signal L : Halt

11 RESET H / L Reset Signal L : Reset

12 D0 H / L Display Data

13 D1 H / L Display Data

14 D2 H / L Display Data

15 D3 H / L Display Data

16 D4 H / L Display Data

17 D5 H / L Display Data

18 D6 H / L Display Data

19 D7 H / L Display Data

20 NC -Non-connection

21 LED A -LED Anode Terminal

22 LED K -LED Cathode Terminal

4.2. Example of Power Supply

It is recommended to apply a potentiometer for the contrast adjust due to the

tolerance of the driving voltage and its temperature dependence.

MODULE

VCONT

VDD

VEE

VSS VSS (0V)

VDD (+Voltage)

R1+R2+VR=10~

KΩ

VEE (-Voltage)

DMF5001NYJ-LY-AQE-AZ (AZ) No. 2001-0245 OPTREX CORPORATION Page 10/17

4.3. Block Diagram

VCONT

VSS

VDD

HALT

D0∼D7

C/D

RESET

T6A40 × 2

T6963C

Control LSI

Row Driver

T6A39 × 2

AB mix Circuit

Column Driver

L C D P

CDATA

HSCP,ED

160

160 × 128 dots

To LSIBias Circuit

128

815

64K S-RAM

X-tal

VEE

or equivalent

LED K

LED A LED Backlight

DMF5001NYJ-LY-AQE-AZ (AZ) No. 2001-0245 OPTREX CORPORATION Page 11/17

5. Test

No change on display and in operation under the following test condition.

Conditions: Unless otherwise specified, tests will be conducted under the following condition.

Temperature: 20±5°C

Humidity : 65±5%RH

tests will be not conducted under functioning state.

No. Parameter Conditions Notes

1High Temperature Operating 60°C±2°C, 96hrs (operation state)

2Low Temperature Operating -10°C±2°C, 96hrs (operation state) 1

3High Temperature Storage 70°C±2°C, 96hrs 2

4Low Temperature Storage -20°C±2°C, 96hrs 1,2

5Damp Proof Test 40°C±2°C,90~95%RH, 96hrs 1,2

6Vibration Test Total fixed amplitude : 1.5mm 3

Vibration Frequency : 10~55Hz

One cycle 60 seconds to 3 directions of X, Y, Z for

each 15 minutes

7Shock Test To be measured after dropping from 60cm high on

the concrete surface in packing state.

Note 1 :No dew condensation to be observed.

Note 2 :The function test shall be conducted after 4 hours storage at the normal

Temperature and humidity after removed from the test chamber.

Note 3 :Vibration test will be conducted to the product itself without putting it in a container.

60cm

Concrete Surface

Dropping method corner dropping

E,F,G face : once

B,C,D edge : once

A corner : once

Face dropping

Edge dropping

DMF5001NYJ-LY-AQE-AZ (AZ) No. 2001-0245 OPTREX CORPORATION Page 12/17

6. Appearance Standards

6.1. Inspection conditions

The LCD shall be inspected under 40W white fluorescent light.

The distance between the eyes and the sample shall be more than 30cm.

All directions for inspecting the sample should be within 45°against perpendicular line.

6.2. Definition of applicable Zones

A Zone : Active display area

B Zone : Area from outside of "A Zone" to validity viewing area

C Zone : Rest parts

A Zone + B Zone = Validity viewing area

A Zone

B Zone

C Zone

Bezel Flame

DMF5001NYJ-LY-AQE-AZ (AZ) No. 2001-0245 OPTREX CORPORATION Page 13/17

6.3. Standards

No. Parameter Criteria

1Black and (1) Round Shape

White Spots, Zone Acceptable Number

Foreign Substances Dimension (mm) A B C

D ≤0.1 * * *

0.1 < D ≤0.2 35*

0.2 < D ≤0.25 23*

0.25< D ≤0.3 01*

0.3 < D 00*

D = ( Long + Short ) / 2 * : Disregard

(2) Line Shape

Zone Acceptable Number

X (mm) Y (mm) A B C

-0.03 ≥ W * * *

2.0 ≥ L 0.05 ≥ W 33*

1.0 ≥ L 0.1 ≥ W 33*

-0.1 < W In the same way (1)

X : Length Y : Width * : Disregard

Total defects shall not exceed 5.

2Air Bubbles

(between glass Zone Acceptable Number

& polarizer) Dimension (mm) A B C

D ≤0.3 * * *

0.3 < D ≤0.4 3* *

0.4 < D ≤0.6 23*

0.6 < D 00*

* : Disregard

Total defects shall not exceed 3.

DMF5001NYJ-LY-AQE-AZ (AZ) No. 2001-0245 OPTREX CORPORATION Page 14/17

No. Parameter Criteria

3The Shape of Dot (1) Dot Shape (with Dent)

As per the sketch of left hand.

(2) Dot Shape (with Projection)

Should not be connected to next dot.

(3) Pin Hole

(X+Y) / 2 ≤ 0.2mm

(Less than 0.1mm is no counted.)

(4) Deformation

(X+Y) / 2 ≤ 0.2mm

Total acceptable number : 1/dot, 5/cell

(Defect number of (4) : 1pc.)

4Polarizer Scratches Not to be conspicuous defects.

5Polarizer Dirts If the stains are removed easily from LCDP surface, the module is not

defective.

6Complex Foreign Black spots, line shaped foreign substances or air bubbles between

Substance Defects glass & polarizer should be 5pcs maximum in total.

7Distance between D ≤ 0.2 : 20mm or more

Different Foreign 0.2 < D : 40mm or more

Substance Defects

0.15

≥

DMF5001NYJ-LY-AQE-AZ (AZ) No. 2001-0245 OPTREX CORPORATION Page 15/17

7. Code System of Production Lot

The production lot of module is specified as follows.

Factory Number (Numeral)

Factory Code (Alphabet)

Production Week (1~5)

Production Month (1~9, X, Y, Z)

Production Year (Lower 2 digits)

8. Type Number

The type number of module is specified on the back of module as follows.

DMF5001NYJ-LY-AQE-AZ

Stamp or Seal

9. Applying Precautions

Please contact us when questions and/or new problems not specified in this

specificationsarise.

DMF5001NYJ-LY-AQE-AZ (AZ) No. 2001-0245 OPTREX CORPORATION Page 16/17

10. Precautions Relating Product Handling

The Following precautions will guide you in handling our product correctly.

1) Liquid crystal display devices

1. The liquid crystal display device panel used in the liquid crystal display module is

made of plate glass. Avoid any strong mechanical shock. Should the glass break

handle it with care.

2. The polarizer adhering to the surface of the LCD is made of a soft material.

Guard against scratching it.

2) Care of the liquid crystal display module against static electricity discharge.

1. When working with the module, be sure to ground your body and any electrical

equipment you may be using. We strongly recommend the use of anti static mats

( made of rubber ), to protect work tables against the hazards of electrical shock.

2. Avoid the use of work clothing made of synthetic fibers. We recommend cotton

clothing or other conductivity-treated fibers.

3. Slowly and carefully remove the protective film from the LCD module, since this

operation can generate static electricity.

3) When the LCD module alone must be stored for long periods of time:

1. Protect the modules from high temperature and humidity.

2. Keep the modules out of direct sunlight or direct exposure to ultraviolet rays.

3. Protect the modules from excessive external forces.

4) Use the module with a power supply that is equipped with an overcurrent protector

circuit, since the module is not provided with this protective feature.

5) Do not ingest the LCD fluid itself should it leak out of a damaged LCD module.

Should hands or clothing come in contact with LCD fluid, wash immediately with soap.

6) Conductivity is not guaranteed for models that use metal holders where solder

connections between the metal holder and the PCB are not used. Please contact

us to discuss appropriate ways to assure conductivity.

7) For models which use CFL:

1. High voltage of 1000V or greater is applied to the CFL cable connector area.

Care should be taken not to touch connection areas to avoid burns.

2. Protect CFL cables from rubbing against the unit and thus causing the wire jacket

to become worn.

3. The use of CFLs for extended periods of time at low temperatures will significantly

shorten their service life.

8) For models which use touch panels:

1. Do not stack up modules since they can be damaged by components on neighboring

modules.

2. Do not place heavy objects on top of the product. This could cause glass breakage.

9) For models which use COG,TAB,or COF:

1. The mechanical strength of the product is low since the IC chip faces out

unprotected from the rear.

Be sure to protect the rear of the IC chip from external forces.

2. Given the fact that the rear of the IC chip is left exposed, in order to protect the unit

from electrical damage, avoid installation configurations in which the rear of the IC

chip runs the risk of making any electrical contact.

DMF5001NYJ-LY-AQE-AZ (AZ) No. 2001-0245 OPTREX CORPORATION Page 17/17

10) Models which use flexible cable, heat seal, or TAB:

1. In order to maintain reliability, do not touch or hold by the connector area.

2. Avoid any bending, pulling, or other excessive force, which can result in broken

connections.

11) In case of buffer material such as cushion / gasket is assembled into LCD module,

it may have an adverse effect on connecting parts ( LCD panel-TCP / HEAT SEAL /

FPC / etc., PCB-TCP / HEAT SEAL / FPC etc., TCP-HEAT SEAL, TCP-FPC, HEAT

SEAL-FPC, etc.,) depending on its materials.

Please check and evaluate these materials carefully before use.

12) In case of acrylic plate is attached to front side of LCD panel, cloudiness ( very

small cracks ) can occur on acrylic plate, being influenced by some components

generated from polarizer film.. Please check and evaluate those acrylic materials

carefully before use.

11. Warranty

This product has been manufactured to your company’s specifications as a part for use

in your company’s general electronic products. It is guaranteed to perform according to

delivery specifications. For any other use apart from general electronic equipment, we

cannot take responsibility if the product is used in medical devices, nuclear power

control equipment, aerospace equipment, fire and security systems, or any other

applications in which there is a direct risk to human life and where extremely high levels

of reliability are required. If the product is to be used in any of the above applications,

we will need to enter into a separate product liability agreement.

1. We cannot accept responsibility for any defect, which may arise from additional

manufacturing of the product (including disassembly and reassembly), after product

delivery.

2. We cannot accept responsibility for any defect, which may arise after the application

of strong external force to the product.

3. We cannot accept responsibility for any defect, which may arise due to the application

of static electricity after the product has passed your company’s acceptance

inspection procedures.

4. When the product is in CFL models, CFL service life and brightness will vary according

to the performance of the inverter used, leaks, etc. We cannot accept responsibility

for product performance, reliability, or defect, which may arise.

5. We cannot accept responsibility for intellectual property of a third party, which may

arise through the application of our product to your assembly with exception to those

issues relating directly to the structure or method of manufacturing of our product.

6. Optrex will not be held responsible for any quality guarantee issue for defect products

judged as Optrex-origin longer than 2 (two) years from Optrex production or 1(one)

year from Optrex, Optrex America, Optrex Europe, Display LC delivery which ever

comes later.