Plastic platform
Voltage
Capacitance
Voltage mark for 6.3V is 6V .
Lot No.
Positive
Negative
U
1Z
2S
31
4C
51
60
70
8M
9C
10 L
11 1
12 G
13 B
14
Configuration
Taping code
Capacitance tolerance (+
–
20%)
Rated capacitance (10µF)
Rated voltage (16V)
Series name
Type
A2
10
16V
0.3MAX.
4.5 +0.1
–0.2
φD+
–
0.5
B+
–
0.2
C+
–
0.2
0.5MAX.
A+
–
0.3 A+
–
0.3
E
0.5 to 0.8
ZSseries
4.5mmL Chip Type
Chip type with 4.5mm height.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2002/95/EC).
Chip Type Type numbering system (Example : 16V 10
µ
F)
Specifications
Category
Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
Tangent of loss angle (tan δ)
Stability at Low Temperature
Endurance
Shelf Life
Marking
Performance CharacteristicsItem –40 to + 85°C
4 to 50V
0.1 to 220µF
+
–
20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA) ,whichever is greater.
Black print on the case top.
Measurement frequency : 120Hz, Temperature : 20°C
Measurement frequency : 120Hz
The specifications listed at right shall be met when
the capacitors are restored to 20°C after the rated
voltage is applied for 2000 hours at 85°C.
After storing the capacitors under no load at 85°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
Resistance to soldering
heat
The capacitors are kept on a hot plate for 30 seconds, which is
maintained at 250°C. The capacitors shall meet the
characteristic requirements listed at right when they are
removed from the plate and restored to 20°C.
ZS
Bi-polarized
ZP
WX
ZT
Z–25°C / Z+20°C
Z–40°C / Z+20°C
Rated voltage (V)
Impedance ratio
ZT / Z20 (MAX.)
4
7
15
6.3
4
8
10
3
8
16
2
4
25
2
4
35
2
3
50
2
3
Dimensions
0.1
0.22
0.33
0.47
1
2.2
3.3
4.7
10
22
33
47
100
220
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
101
221
4
4
5
6.3
28
33
56
96
4
5
5
6.3
28
37
45
70
5
5
6.3
33
41
52
4
5
6.3
6.3
23
37
49
58
4
5
6.3
6.3
16
27
42
52
4
5
6.3
18
29
46
4
4
4
4
4
4
4
5
6.3
1.0
2.0
2.8
4.0
8.4
13
17
20
33
Rated
ripple
4
0G 6.3
0J 10
1A 16
1C 25
1E 35
1V 50
1H
V
Code
Rated ripple current (mArms) at 85°C 120Hz
φD
A
B
C
E
4
1.8
4.3
4.3
1.0
5
2.1
5.3
5.3
1.3
6.3
2.4
6.6
6.6
2.2
(mm)
Cap. (µF)
Rated voltage (V)
tan δ(MAX.) 4
0.50 6.3
0.30 10
0.24 16
0.19 25
0.16 35
0.14 50
0.14
Capacitance change
Leakage current
tan δ
Within +
–
10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Capacitance change
Leakage current
tan δ
Within +
–
20% of the initial capacitance value
200% or less than the initial specified value
Less than or equal to the initial specified value
High
Temperature
ALUMINUM ELECTROLYTIC CAPACITORS
ZR
Smaller
Smaller
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given
in page 18, 19.
Please select UR(p.104), UG(p.110) series if high C/V
products are reqired.
Please refer to page 3 for the minimum order quantity.
Case size
φD (mm)
Frequency coefficient of rated ripple current
Coefficient
Frequency 50 Hz 120 Hz 300 Hz 1 kHz
10 kHz or more
0.70 1.00 1.17 1.36 1.50
CAT.8100A