IXYS reserves the right to change limits, test conditions and dimensions © 2010 IXYS All rights reserved
IXYS KOREA LTD. 1 IXYS Corporation
906-5 Iui-dong, Yeongtong-Gu, Suwon, Gyeonggi-Do, Korea 1590 Buckeye Drive, Milpitas, CA 95035-7418
Phone +82-31-888-5232, Fax +82-31-888-5233 Rev. Feb. 2011 Phone (408) 457-9000, Fax 408-496-0670
IXOLARTM High Efficiency SolarMD.
Description
IXOLARTM SolarMD is an IXYS product line of Solar Module made of monocrystalline, high efficiency solar
cells. The IXOLARTM SolarMD is an ideal for charging various battery powered and handheld consumer
products such as mobile phones, cameras, PDAs, MP3-Players and toys. They are also suitable for
industrial applications such as wireless sensors, portable instrumentation and for charging emergency
backup batteries.
With a cell efficiency of typically 22%, SolarMD gives the ability to extend run time even in "low light"
conditions and increase battery life and run time in a small footprint, which can be easily accommodated in
the design of portable products. The design allows connecting SolarMD flexibly in series and/or parallel to
perfectly meet the custom-specific application’s power requirements.
IXOLARTM products have a very good photonic response over a wide range of wavelength and therefore
can be used in both indoor and outdoor applications.
Product and Ordering Information
(parameters given are typical values)
Dimensions (L x W x H): 89 x 67 x 2.0 [mm]
SolarMD Weight: 20 grams
SolarMD are compliant to the RoHS Norm.
SolarMD Electrical Characteristics
Symbol Cell Parameter Typical
Ratings *)
Units
VOC open circuit voltage 6.30
V
ISC short circuit current 200
mA
Vmpp voltage at max. power point 5.00
V
Impp current at max. power point 178
mA
Pmpp maximum peak power 892
mW
FF fill factor > 70
%
η solar cell efficiency 22
%
ΔVOC/ΔT open circuit voltage temp. coefficient -2.1
mV/K
ΔJSC/ΔT short circuit current temp. coefficient 0.12
mA/(cm²K)
*) All values measured at Standard Condition: 1 sun (= 1000 W/m²), Air Mass 1.5, 25°C
Part Number
Open Circuit
Voltage [V]
Short Circuit
Current [mA]
Typ. Voltage
@ Pmpp [V]
Typ. Current
@ Pmpp [mA]
SLMD481H10
6.30 200 5.00 178
Features
• Monocrystalline silicon technology
• High efficiency outdoor and indoor
• Long life and stable output
• Sealed Package
• High mechanical robustness
Applications
• Battery chargers for portables such as cell
phones, PDAs, GPS-Systems, …
• “Green” electricity generation
• Power backup for UPS, Sensors, Wearables
Advantages
• One Product for Multiple Applications
• Flexible Integration into the Application
IXYS reserves the right to change limits, test conditions and dimensions © 2010 IXYS All rights reserved
IXYS KOREA LTD. 2 IXYS Corporation
906-5 Iui-dong, Yeongtong-Gu, Suwon, Gyeonggi-Do, Korea 1590 Buckeye Drive, Milpitas, CA 95035-7418
Phone +82-31-888-5232, Fax +82-31-888-5233 Rev. Feb. 2011 Phone (408) 457-9000, Fax 408-496-0670
Typical SolarMD Performance Data
Open-Circuit Voltage vs. Irradiance External Quantum Efficiency
IXYS reserves the right to change limits, test conditions and dimensions © 2010 IXYS All rights reserved
IXYS KOREA LTD. 3 IXYS Corporation
906-5 Iui-dong, Yeongtong-Gu, Suwon, Gyeonggi-Do, Korea 1590 Buckeye Drive, Milpitas, CA 95035-7418
Phone +82-31-888-5232, Fax +82-31-888-5233 Rev. Feb. 2011 Phone (408) 457-9000, Fax 408-496-0670
Package front-side and back-side view. (dimensions in millimeters)
Front-side View Cell Size
Front-side View details Back-side View details
Moisture Sensitivity, Reflow Soldering and Washing Information
IXYS has characterized the moisture reflow sensitivity of the SolarMD using IPC/JEDEC standard J-STD-020. Moisture uptake from
atmospheric humidity occurs by diffusion. During the soldering process to the electrode, the combination of moisture uptake and high
temperature soldering may lead to moisture induced delamination and cracking of the component. To prevent this, this component
must be handled with the standard soldering process and conditions in accordance with IPC/JEDEC standard J-STD-020 per the
labeled moisture sensitivity level (MSL), level 1. SLMD481H10 is encapsulated by the lamination with EVA and polymer film and thus
excessively high temperatures soldering reflow is prohibited. IXYS does not recommend the use of chlorinated solvents for washing.
Surface Protection Film
Please be advised that SLMD module is normally covered with protection film by factory to prevent it from scratch or dirt during the
transportation, Therefore it is highly recommended to remove the protection film at the end of your work. Especially when SLMD
should go through the high temperature process or environment, the film should be removed in advance. If protection film is not
wanted, please consult the factory.
IXYS reserves the right to change limits, test conditions and dimensions © 2010 IXYS All rights reserved
IXYS KOREA LTD. 4 IXYS Corporation
906-5 Iui-dong, Yeongtong-Gu, Suwon, Gyeonggi-Do, Korea 1590 Buckeye Drive, Milpitas, CA 95035-7418
Phone +82-31-888-5232, Fax +82-31-888-5233 Rev. Feb. 2011 Phone (408) 457-9000, Fax 408-496-0670
Background
Some basic information needs to be covered to better understand what to expect in terms of
the SolarMD’s performance with regards to solar cell type, lighting conditions in terms of
power density, and general industry standards as they relate to battery charging.
Solar Cell Types
Keep in mind these cost and performance tradeoffs when comparing various solar cell
materials:
Polycrystalline cells are commonly found in outdoor applications and have a spectral
sensitivity range of 500nm to 1100nm. They’re in the medium price range and typically offer
a 13% power conversion efficiency.
Monocrystalline cells, such as the IXYS SolarMD, have a spectral sensitivity range from 300
nm (near-ultraviolet) to 1100 nm (near-infrared), which includes visible light (400 to 700 nm).
Due to this wide spectral range, they can be used in both indoor and outdoor applications.
Monocrystalline or single-crystalline material is the most expensive but it does not contain
impurities, and as such the power conversion efficiency does not degrade over operating time.
The power conversion efficiency of commercially available monocrystalline cells ranges from
15 to 22%. The surface of these cells is a homogenous dark blue or dark grey.
Finally, amorphous cells, which work in the spectral range of 300nm to 600nm, are used
predominantly indoors in products such as solar powered calculators since they are not
sensitive to the upper light spectrum and cannot take advantage of natural sunlight. They
offer about 5% power conversion efficiency and are mostly used with ultra low power devices
like clocks and electronic calculators. Amorphous cells, like polycrystalline cells, suffer from
efficiency degradation.
IXYS reserves the right to change limits, test conditions and dimensions © 2010 IXYS All rights reserved
IXYS KOREA LTD. 5 IXYS Corporation
906-5 Iui-dong, Yeongtong-Gu, Suwon, Gyeonggi-Do, Korea 1590 Buckeye Drive, Milpitas, CA 95035-7418
Phone +82-31-888-5232, Fax +82-31-888-5233 Rev. Feb. 2011 Phone (408) 457-9000, Fax 408-496-0670
SolarMD Description
SolarMD is made of monocrystalline, high-efficiency solar cells in a surface mountable package.
They’re robust and can be used in harsh environments. Solar cells used in SolarMD have a very
high (22%) power conversion efficiency, which means that 22% of the light energy is converted
into electrical energy. They’re extremely useful in applications requiring solar power generation in
a limited space.
Monocrystalline cells can be used in indoor and outdoor applications because they have a wide
spectral sensitivity, 300 to 1100 nm. However, the output power of a solar cell is proportional
(over a wide range) to the incoming light energy, and irradiance is generally much higher
outdoors. The values in the data sheet are measured at “standard condition” of 1 sun, which is
equal to 1000W per square meter sunlight irradiance at a defined light spectrum (air mass of 1.5)
and 25°C cell temperature.
Relative Lighting Power Density
The figure above compares relative power density for various lighting conditions in units of Watts
per square meter (W/m2). The reference standard condition is 1 Sun and is equal to 1000 Watts
per square meter of sunlight irradiance at a constant 25°C cell temperature and at 1.5 Air Mass
(Air Mass stands for a well defined light spectrum which appears if the sunlight goes through the
earth’s athmosphere at a defined angle). As the chart clearly shows, the power density of typical
indoor lighting is dramatically lower than that of sunlight. Not only is irradiance from indirect and
artificial light lower; the spectrum is also narrower. In typical Office Space lighting with a
spectrum produced from incandescent or halogen light bulbs, the power output may be roughly
100 times less than bright sunlight. It may be 200 to 500 times less with fluorescent lighting due
to the further limited spectrum.
IXYS reserves the right to change limits, test conditions and dimensions © 2010 IXYS All rights reserved
IXYS KOREA LTD. 6 IXYS Corporation
906-5 Iui-dong, Yeongtong-Gu, Suwon, Gyeonggi-Do, Korea 1590 Buckeye Drive, Milpitas, CA 95035-7418
Phone +82-31-888-5232, Fax +82-31-888-5233 Rev. Feb. 2011 Phone (408) 457-9000, Fax 408-496-0670
IXYS makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the
right to make changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses or indemnity are
expressed or implied. Except as set forth in IXYS’ Standard Terms and Conditions of Sale, IXYS assumes no liability whatsoever, and disclaims
any express or implied warranty relating to its products, including, but not limited to, the implied warranty of merchantability, fitness for a particular
purpose, or infringement of any intellectual property right.
The products described in this document are not designed, intended, authorized, or warranted for use as components in systems intended for
surgical implant into the body, or in other applications intended to support or sustain life, or where malfunction of IXYS’ product may result in direct
physical harm, injury, or death to a person or severe property or environmental damage. IXYS reserves the right to discontinue or make changes to
its products at any time without notice.
