Part No: CEP-1173
Description: piezo audio transducer
Phone: 800.275.4899 Fax: 503.612.2381 www.cui.com 20050 SW 112th Ave. Tualatin, OR 97062
Date: 6/25/2007
Unit: mm
Page No: 1of 4
Specifications
Resonant frequency 3.3 KHz ± 0.5
Operating voltage 3 ~ 28 V dc
Current consumption 7 mA max. at 12 V dc
Sound pressure level 82 db min. at 30 cm / 12 V dc
Rated voltage 12 V dc
Tone Continuous
Operating temperature -30 ~+80° C
Storage temperature -40 ~ +95° C
Dimensions ø32.0 x H13.5 mm
Weight 7.4 g max.
Material ABS UL-94 1/16” HB (Black)
Terminal Wire type
RoHS yes
Appearance Drawing
Tolerance: ±0.5
red wire
blue wire
black wire
---M
---F
---G
For more information, please visit the product page.
Part No: CEP-1173
Description: piezo audio transducer
Phone: 800.275.4899 Fax: 503.612.2381 www.cui.com 20050 SW 112th Ave. Tualatin, OR 97062
Date: 6/25/2007
Unit: mm
Page No: 3of 4
Environment Test
Item Test Condition
High temp. test After being placed in a chamber at +95°C for
240 hours.
Low temp. test After being placed in a chamber at -40°C for
240 hours.
Humidity test After being placed in a chamber at +40°C and
90±5% relative humidity for 240 hours.
Temp. cycle test The part shall be subjected to 5 cycles. One
cycle will consist of:
Evaluation Standard
The buzzer will be measured after
being placed at +25°C for 4
hours. The value of the
oscillation frequency/current
consumption should be ±10%
compared to the initial
measurements. The SPL should
be within ±10dB compared to the
initial measurements.
Mechanical Characteristics
Item Test Condition
Solderability Stripped wires of lead wires are immersed in
(Connector excepted) rosin for 5 seconds and then immersed in
a solder bath of +270 ±5°C for 3 ±0.5 seconds.
Terminal Mechanical Strength The pull force should be applied to the double
lead wire:
Horizontal 3.0N (0.306kg) for 30 seconds
Vertical 2.0N (0.204kg) for 30 seconds
Vibration The buzzer shall be measured after applying
a vibration amplitude of 1.5 mm with 10 to
55 Hz band of vibration frequency to each of
the 3 perpendicular directions for 2 hours.
Drop Test The part will be dropped from a height of
75 cm onto a 40 mm thick wooden board 3
times in 3 axes (X, Y, Z) for a total of 9 drops.
Evaluation Standard
90% min. of the stripped wires
will be wet with solder.
(Except the edge of the terminal)
No damage or cutting off.
The value of oscillation
frequency/current consumption
should be ±10% of the initial
measurements. The SPL should
be within ±10dB compared with
the initial measurement.
For more information, please visit the product page.
Part No: CEP-1173
Description: piezo audio transducer
Phone: 800.275.4899 Fax: 503.612.2381 www.cui.com 20050 SW 112th Ave. Tualatin, OR 97062
Date: 6/25/2007
Unit: mm
Page No: 4of 4
Reliability Test
Item Test Condition
Operating (Life Test) 1. Continuous life test:
The part will be subjected to 48 hours of
continuous operation at +65°C with rated
voltage applied.
2. Intermittent life test:
Aduty cycle of 1 minute on, 1 minute off, a
minimum of 5,000 times at room temp
(+25 ±2°C) with rated voltage applied.
Evaluation Standard
The buzzer will be measured after
being placed at +25°C for 4
hours. The value of the
oscillation frequency/current
consumption should be ±10%
compared to the initial
measurements. The SPL should
be within ±10dB compared to
the initial measurements.
Test Conditions
Standard Test Condition a) Tempurature: +5 ~ +35°C b) Humidity: 45 - 85% c) Pressure: 860-1060 mbar
Judgement Test Condition a) Tempurature: +25 ±2°C b) Humidity: 60 - 70% c) Pressure: 860-1060 mbar
Packaging
For more information, please visit the product page.
