HAS30 DC-DC Series Data Sheet Features * * * * * * * * * RoHS lead solder exemption compliant Industry standard half-brick Low-cost design 100 C baseplate operation Open-frame packaging 24 V and 48 V input versions Input Pi filter Optional enable logic 1500 V isolation Description HAS dc-dc converters provide up to 30 watts of output power in an industry-standard package and footprint. With a maximum case temperature of 100 C, the HAS is well suited for the most demanding telecom, networking, and industrial applications. The HAS features 1500 VDC isolation, short circuit, and overtemperature protection, as well as six-sided shielding. The HAS series is available with optional enable and voltage trim pins. Please see the HAD Series for dual-output applications. Technical Specifications Efficiency vs. Load (24V Input) Input Voltage Range 24 VDC Nominal 48 VDC Nominal Transient Reflected Ripple 90 85 EFFICIENCY % 18 - 36 VDC 36 - 75 VDC 100V/100ms 50 mA 80 HAS030YG-A 75 EFF. (24v) 70 Output EFF. (36v) 1% 0.2% Vout 0.2% Vout 0.5 VDC 10 % 25% Iout 4% Vout 500 s 10% Hiccup 110 - 140% 115 - 140% Vout Nom. Vin Negative 10 mA Max. 65 60 10 20 30 40 50 60 90 100 90 100 95 90 85 80 75 70 HAS030ZH-A 65 HAS030ZG-A HAS030ZJ-A 55 General REV. FEB 01, 2006 80 Efficiency vs. Load (48V Input) 60 Turn-On Time Remote Shutdown Switching Frequency Isolation Input - Output Input - Case Output - Case Temperature Coefficient Case Temperature Operating Range Storage Range Humidity Max., Non-Condensing Vibration, 3 Axes, 5 Min Each MTBF (Bellcore TR-NWT-000332) Safety Weight (Approx.) 70 LOAD % EFFICIENCY % Setpoint Accuracy Line Regulation Vin Min. - Vin Max., Iout Rated Load Regulation Iout Min. - Iout Max., Vin Nom. Remote Sense Headroom Minimum Output Current Dynamic Regulation, Loadstep Pk Deviation Settling Time Voltage Trim Range Short Circuit / Overcurrent Protection Current Limit Threshold Range, % of Iout Rated OVP Trip Range Remote Shutdown Reference Shutdown Pin Current, Sourced At Off EFF. (18v) 50 10 ms Positive/Negative Logic 250 kHz 1500 VDC 1050 VDC 500 VDC 0.03%/C -40 To +100 C -40 To +125 C 95% 5 g, 10 - 55 Hz 2.5 X 106 hrs UL, cUL, TUV 1.4 oz Page 1 of 3 10 20 30 40 50 60 70 80 LOAD % Notes MTBF predictions may vary slightly from model to model. Specifications typically at 25 C, normal line, and full load, unless otherwise stated. Soldering Conditions: I/O pins, 260 C, ten seconds; fully compatible with commercial wave-soldering equipment. Safety: Agency approvals may vary from model to model. Please consult factory for specific model information. Units are water-washable and fully compatible with commercial spray or immersion post wave-solder washing equipment. www.power-one.com HAS30 DC-DC Series Data Sheet Model Selection MODEL INPUT VOLTAGE (VOLTS) INPUT VOLTAGE RANGE (VOLTS) MAXIMUM INPUT CURRENT (AMPS)* OUTPUT VOLTAGE (VOLTS) RATED OUTPUT CURRENT (AMPS) 24 24 24 48 48 48 48 18-36 18-36 18-36 36-75 36-75 36-75 36-75 2.2 2.2 2.2 1.0 1.3 1.3 1.3 5 12 15 3.3 5 12 15 6.0 2.5 2.0 6.0 6.0 2.5 2.0 HAS030YG-A HAS030YH-A HAS030YJ-A HAS030ZE-AT HAS030ZG-A HAS030ZH-A HAS030ZJ-A RIPPLE & NOISE pk-pk (mV) TYPICAL EFFICIENCY** 100 150 150 100 100 150 150 83% 87% 86% 81% 83% 88% 88% NOTES: * Maximum input current at minimum input voltage, maximum rated output power. ** At nominal Vin, rated output. Model numbers highlighted in yellow or shaded are not recommended for new designs. Mechanical Drawing MOUNTING INSERTS M3X.5 THROUGH 4PL 2.28" (57.9mm) 0.18" (4.6mm) 1.700"(43.2mm) 1.400"(35.6mm) 1 5 1.400"(35.6mm) 1.000"(25.4mm) 2 6 1.000"(25.4mm) 7 0.700"(17.8mm) 0.400"(10.2mm) BOTTOM VIEW 0.400"(10.2mm) 3 8 0 4 9 DIA 0.040" (1.0mm) 2.40" (61.0mm) 0 -0.300"(-7.6mm) -0.300"(-7.6mm) -0.50"(-12.7mm) -0.19" (-4.8mm) Thermal Impedance Natural Convection 100 LFM 200 LFM 300 LFM 400 LFM 7.9 C/W 6.8 C/W 4.9 C/W 3.6 C/W 3.0 C/W Note: Thermal impedance data is dependent on many environmental factors. The exact thermal performance should be validated for specific application. 0 0.025" REF. (0.6mm) 1.900" (48.3mm) Pin 0.50" (12.7mm) Tolerances Function 1 -Vin 2 3 4 Case On/Off +Vin 5 -Vout 6 7 8 9 -Sense Trim +Sense +Vout Inches: .XX 0.020 .XXX 0.010 Pin: 0.002 (Millimeters) .X 0.5 .XX 0.25 0.05 (Dimensions as listed unless otherwise specified.) NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the respective divisional president of Power-One, Inc. TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice. REV. FEB 01, 2006 Page 2 of 3 www.power-one.com OPTIONS Ordering Information Suffix Code Identification: Series Applicability: HAS, HBD, HBS, HES, QBS, QES, TES, TQD Features & Options Descriptions Suffix Code Remote ON/OFF Positive Logic Negative Logic None N Trim Standard Power-One (Negative) Industry-standard (Positive) None T Pin Length 0.18" (4.6mm), standard model length None 0.145" (3.68mm) 7 0.110" (2.8mm) 8 Special Options Customer-specific models S# NOTE: Contact factory for availability of specific options. REV. FEB 01, 2006 Page 3 of 3 www.power-one.com