•
RoHS lead solder exemption compliant
• Industry standard half-brick
• Low-cost design
• 100 °C baseplate operation
• Open-frame packaging
• 24 V and 48 V input versions
• Input Pi filter
• Optional enable logic
• 1500 V isolation
Features
HAS dc-dc converters provide up to 30 watts of output power in an industry-standard package and footprint. With a
maximum case temperature of 100 °C, the HAS is well suited for the most demanding telecom, networking, and
industrial applications. The HAS features 1500 VDC isolation, short circuit, and overtemperature protection, as well
as six-sided shielding. The HAS series is available with optional enable and voltage trim pins. Please see the HAD
Series for dual-output applications.
Description
Technical Specifications
Voltage Range
24 VDC Nominal 18 - 36 VDC
48 VDC Nominal 36 - 75 VDC
Transient 100V/100ms
Reflected Ripple 50 mA
Input
Setpoint Accuracy ±1%
Line Regulation Vin Min. - Vin Max., Iout Rated 0.2% Vout
Load Regulation Iout Min. - Iout Max., Vin Nom. 0.2% Vout
Remote Sense Headroom 0.5 VDC
Minimum Output Current 10 %
Dynamic Regulation, Loadstep 25% Iout
Pk Deviation 4% Vout
Settling Time 500 µs
Voltage Trim Range ±10%
Short Circuit / Overcurrent Protection Hiccup
Current Limit Threshold Range, % of Iout Rated 110 - 140%
OVP Trip Range 115 - 140% Vout Nom.
Remote Shutdown Reference Vin Negative
Shutdown Pin Current, Sourced At Off 10 mA Max.
Output
General
Turn-On Time 10 ms
Remote Shutdown Positive/Negative Logic
Switching Frequency 250 kHz
Isolation
Input - Output 1500 VDC
Input - Case 1050 VDC
Output - Case 500 VDC
Temperature Coefficient 0.03%/°C
Case Temperature
Operating Range -40 To +100 °C
Storage Range -40 To +125 °C
Humidity Max., Non-Condensing 95%
Vibration, 3 Axes, 5 Min Each 5 g, 10 - 55 Hz
MTBF†(Bellcore TR-NWT-000332) 2.5 X 106hrs
Safety UL, cUL, TUV
Weight (Approx.) 1.4 oz
50
55
60
65
70
75
80
85
90
95
10 20 30 40 50 60 70 80 90 100
LOAD %
EFFICIENCY %
HAS030ZH-A
HAS030ZG-A
HAS030ZJ-A
HAS030YG-A
60
65
70
75
80
85
90
10 20 30 40 50 60 70 80 90 100
LOAD %
EFFICIENCY %
EFF. (18v)
EFF. (24v)
EFF. (36v)
Efficiency vs. Load (48V Input)
Efficiency vs. Load (24V Input)
Notes
†MTBF predictions may vary slightly from model to model.
Specifications typically at 25 °C, normal line, and full load, unless
otherwise stated.
Soldering Conditions: I/O pins, 260 °C, ten seconds; fully compatible
with commercial wave-soldering equipment.
Safety: Agency approvals may vary from model to model. Please
consult factory for specific model information.
Units are water-washable and fully compatible with commercial spray
or immersion post wave-solder washing equipment.
HAS30 DC-DC Series Data Sheet
REV. FEB 01, 2006 Page 1 of 3 www.power-one.com
MODEL INPUT VOLTAGE INPUT VOLTAGE MAXIMUM INPUT OUTPUT RATED OUTPUT RIPPLE & NOISE TYPICAL
(VOLTS) RANGE (VOLTS) CURRENT (AMPS)* VOLTAGE (VOLTS) CURRENT (AMPS) pk-pk (mV) EFFICIENCY**
HAS030YG-A 24 18-36 2.2 5 6.0 100 83%
HAS030YH-A 24 18-36 2.2 12 2.5 150 87%
HAS030YJ-A 24 18-36 2.2 15 2.0 150 86%
HAS030ZE-AT 48 36-75 1.0 3.3 6.0 100 81%
HAS030ZG-A 48 36-75 1.3 5 6.0 100 83%
HAS030ZH-A 48 36-75 1.3 12 2.5 150 88%
HAS030ZJ-A 48 36-75 1.3 15 2.0 150 88%
NOTES:
* Maximum input current at minimum input voltage, maximum rated output power.
** At nominal Vin, rated output.
Model Selection
Mechanical Drawing
1
2
3
4
5
6
7
8
9
0.700"(17.8mm)
1.400"(35.6mm)
1.000"(25.4mm)
0.400"(10.2mm)
0
0.18"
2.28"
(57.9mm)
DIA 0.040"
0.025" REF.
0.50"
(12.7mm)
(4.6mm)
(1.0mm)
MOUNTING INSERTS
M3X.5 THROUGH 4PL
(0.6mm)
BOTTOM VIEW
1.700"(43.2mm)
-0.50"(-12.7mm)
-0.300"(-7.6mm) -0.300"(-7.6mm)
1.400"(35.6mm)
1.000"(25.4mm)
0.400"(10.2mm)
0
0
(-4.8mm)
-0.19"
(48.3mm)
1.900"
(61.0mm)
2.40
"
Thermal Impedance
Natural Convection 7.9 °C/W
100 LFM 6.8 °C/W
200 LFM 4.9 °C/W
300 LFM 3.6 °C/W
400 LFM 3.0 °C/W
Tolerances
Note:
Thermal impedance data is
dependent on many environmental
factors. The exact thermal
performance should be validated
for specific application.
1-V
in
2 Case
3 On/Off
4+V
in
5-V
out
6 -Sense
7 Trim
8 +Sense
9+V
out
Inches: (Millimeters)
.XX ± 0.020 .X ± 0.5
.XXX ± 0.010 .XX ± 0.25
Pin:
± 0.002 ± 0.05
(Dimensions as listed unless
otherwise specified.)
Pin Function
HAS30 DC-DC Series Data Sheet
REV. FEB 01, 2006 Page 2 of 3 www.power-one.com
Model numbers highlighted in yellow or shaded are not recommended for new designs.
NUCLEAR AND MEDICALAPPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical components
in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the respective
divisional president of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the
date manufactured. Specifications are subject to change without notice.
OPTIONS
REV. FEB 01, 2006 Page 3 of 3 www.power-one.com
Series Applicability: HAS, HBD, HBS, HES, QBS, QES, TES, TQD
Features & Options Descriptions Suffix Code
Remote ON/OFF Positive Logic None
Negative Logic N
Trim Standard Power-One (Negative) None
Industry-standard (Positive) T
Pin Length 0.18” (4.6mm), standard model length None
0.145” (3.68mm) 7
0.110” (2.8mm) 8
Special Options Customer-specific models S#
NOTE: Contact factory for availability of specific options.
Ordering Information
Suffix Code Identification:
