MLX90242ESO-CC03 - Melexis - Datasheet.Directory

MLX90242

Linear Hall Effect Sensor

3901090242 Page 1 of 7 Data Sheet

Rev. 024 Mar/04

Features and Benefits

• Small Plastic Package (SOT-23, 4-SIP-VA, TO-92)

• Quad Switched Hall Plate / Chopper Stabilized Amplifier

• Ratiometric Output for A/D Interface

• Low Quiescent Voltage Thermal Drift

Applications

• Linear Position Sensing

• Rotary Position Sensing

• Current Sensing

Ordering Information

Part No. Sensitivity Voq TC Temp. Range Package Nb pins

MLX90242LUA-CC03 40 mV/mT (± 500G) 2.50 V 700 ppm/°C -40C to 150C UA 3

MLX90242LVA-CC03 40 mV/mT (± 500G) 2.50 V 700 ppm/°C -40C to 150C VA 4

MLX90242ESO-BC03 15 mV/mT (± 1300G) 2.50 V - -40C to 85C SO 3

MLX90242ESO-CC03 40 mV/mT (± 500G) 2.50 V - -40C to 85C SO 3

1. Functional Diagram

Chopper

Output

Package Pin1 Pin2

Pin 3

Pin4 Slope

SOT23 VDD Out VSS Positive

UA VDD VSS Out Negative

VA VDD n/c VSS Out Positive

2. Description

The MLX90242 is a CMOS Linear Hall Effect

sensor IC. It possesses active error correction

circuitry which virtually eliminates the offset

errors normally associated with analog Hall

Effect devices.

The ratiometric output voltage is proportional to

the supply voltage. When using the supply

voltage as a reference for an A/D converter,

fluctuations of +10% in supply voltage will not

affect accuracy. For a positive slope, the voltage

at the output will increase as a South magnetic

field is applied to the branded face of the

MLX90242. Conversely, the voltage output will

decrease in the presence of a North magnetic

field. For a negative slope, the voltage at the

output will increase as a North magnetic field is

applied to the branded face of the MLX90242.

Conversely, the voltage output will decrease in

the presence of a South magnetic field.

MLX90242

Linear Hall Effect Sensor

3901090242 Page 2 of 7 Data Sheet

Rev. 024 Mar/04

TABLE OF CONTENTS

FEATURES AND BENEFITS..............................................................................................................1

APPLICATIONS .................................................................................................................................1

ORDERING INFORMATION...............................................................................................................1

1. FUNCTIONAL DIAGRAM ......................................................................................................... 1-1

2. DESCRIPTION ......................................................................................................................... 2-1

3. GLOSSARY OF TERMS..............................................................................................................3

4. ABSOLUTE MAXIMUM RATINGS ...............................................................................................3

5. MLX90242 ELECTRICAL SPECIFICATIONS................................................................................4

6. MLX90242 MAGNETIC SPECIFICATIONS ...................................................................................4

7. APPLICATIONS INFORMATION..................................................................................................5

8. INSTALLATION COMMENTS......................................................................................................5

9. RELIABILITY INFORMATION......................................................................................................5

10. ESD PRECAUTIONS ...................................................................................................................6

11. PACKAGE INFORMATION..........................................................................................................6

MLX90242

Linear Hall Effect Sensor

3901090242 Page 3 of 7 Data Sheet

Rev. 024 Mar/04

3. Glossary of Terms

- Gauss, Tesla: Two units to quantify a magnetic flux density. Conversion: 1 mT = 10 Gauss

- Voq: Quiescent output voltage. Output voltage for B = 0.

4. Absolute Maximum Ratings

Supply Voltage (Over Voltage), VDD 7.0 V

Output Current Short to Vdd 5 mA

Output Current Short to Vss 0.5 mA

Output Pin Short to Vss Pin Infinite

Output Over Voltage 8 V

Operating Temperature Range, TA -40°C to 150°C

Storage Temperature Range, TS -55°C to 150°C

Maximun Junction Temp, TJ 170°C

Magnetic Flux Density Infinite

Exceeding the absolute maximum ratings may cause permanent damage. Exposure to absolute-

maximum-rated conditions for extended periods may affect device reliability.

MLX90242

Linear Hall Effect Sensor

3901090242 Page 4 of 7 Data Sheet

Rev. 024 Mar/04

5. MLX90242 Electrical Specifications

DC Operating Parameters. L: TA = -40 to 150°C, E: TA = -40 to 85°C

VDD = 5.0V (Unless otherwise specified)

Parameter Symbol Test Conditions Min Typ Max Units

Supply Voltage VDD Operating 4.5 5.0 5.5 V

Supply Current IDD B = 0, VDD = 5V, IOUT = 0 1.8 2.5 4.5 mA

Output Current IOUT VDD = 5V

Pull-up = 5 kO, Pull-down = 50 kO

-1.0 - 0.1 mA

Quiescent Output Voltage VOQ B = 0, TA = 25°C 2.4 2.5 2.6 V

Output Voltage VOH VDD = 5V, IOUT = -1.0 mA 4.75 V

Output Voltage VOL VDD = 5V, IOUT = 0.1 mA 0.25 V

Response Time tr Vdd=5V,Vout from Voq to VOH/VOL

without load

400 800 µS

Noise (RMS) 5 10 mV

Output Resistance ROUT 20 Ω

Linearity Error Le 0.5 %Vdd

6. MLX90242 Magnetic Specifications

L: TA = -40 to 150°C, E: T A = -40 to 85°C

VDD = 5.0V (Unless otherwise specified)

Parameter Symbol MLX90242LUA-CC03 MLX90242LVA-CC03 MLX90242ESO-BC03 MLX90242ESO-CC03

Min Typ Max Min Typ Max Min Typ Max Min Typ Max

Thermal Voq Drift (1)

(mV) ∆ΤVOQ -25 25 -25 25 +/- 25 (2) +/- 25 (2)

Sensitivity, TA = 25° C

(mV/mT)

S 33.2 39.0 44.9 35.3 41.5 47.7 11.5 15 17.3 33.2 39.0 44.9

TC of Sensitivity

(ppm/°C)

TCS 430 680 930 430 680 930 680 (2) 680 (2)

(1) B = 0, TA = -40 to 150°C

(2) For ESO package, TC of Sensitivity and Thermal Voq Drift are not fully tested and therefore cannot be specified.

Characterization and statistic data can be provided by Melexis upon request.

MLX90242

Linear Hall Effect Sensor

3901090242 Page 5 of 7 Data Sheet

Rev. 024 Mar/04

7. Applications Information

C1 and C2 values can be trimmed to satisfied

EMC requirements according to the environment

(PCB, connectors,...).

The output rise time is affected for large

capacitor C2, depending of the couple R1;C2.

8. Installation Comments

1.) Avoid mechanical stress on leads or

package.

Stress may cause VOQ shift.

A.) Avoid bending leads at the package interface.

B.) Support the leads by clamping, when bending.

C.) Avoid gluing device to another material.

This may cause temperature-related stress.

2.) CMOS products are static sensitive devices,

please observe ESD precautions.

3.) Observe temperature limits during soldering

Recommended Wiring

C1 = 10nF

C2 = 2.5nF

MLX

90242

1 2

OUT

R1 = 10 k

9. Reliability Information

Melexis devices are classified and qualified regarding suitability for infrared, vapor phase and wave

soldering with usual (63/37 SnPb-) solder (melting point at 183degC).

The following test methods are applied:

IPC/JEDEC J-STD-020A (issue April 1999)

Moisture/Reflow Sensitivity Classification For Nonhermetic Solid State Surface Mount Devices

CECC00802 (issue 1994)

Standard Method For The Specification of Surface Mounting Components (SMDs) of Assessed Quality

MIL 883 Method 2003 / JEDEC-STD-22 Test Method B102

Solderability

For all soldering technologies deviating from above mentioned standard conditions (regarding peak

temperature, temperature gradient, temperature profile etc) additional classification and qualification tests

have to be agreed upon with Melexis. For process using through hole components, a temperature profile

of 235 Deg.C during 30 seconds maximum is tolerated.

The application of Wave Soldering for SMD’s is allowed only after consulting Melexis regarding assurance

of adhesive strength between device and board. Please contact MLX for Ua part used as SMD device.

For more information on manufacturability/solderability see quality page at our website:

http://www.melexis.com/

MLX90242

Linear Hall Effect Sensor

3901090242 Page 6 of 7 Data Sheet

Rev. 024 Mar/04

10. ESD Precautions

Electronic semiconductor products are sensitive to Electro Static Discharge (ESD).

Always observe Electro Static Discharge control procedures whenever handling semiconductor products.

11. Package Information

42GA

2053

1 2 3

All Dimensions in millimeters

1.95 +/- 0.15 0.45

0.41

Marked

Surface

1.52+/-0.15

UA Hall Plate / Chip Location

1.60

1.40

45o

Typical

4.30

3.90

2.64

2.34

0.84

0.63

3.20

2.80

1.75

1.55

0.48

0.43

0.20

0.00

0.41

0.35

1.30

1.24 2.57

2.51

0.38

Typical

(see note 3)

15.0

14.0

0.41

0.35

UA Package Dimensions

* MARKING:

Line 1:

1st and 2nd digits (42) = Part Number MLX90242

3rd and 4th digits (GA) = Version number

Line 2:

1st digit (2) = Year (2002)

2nd and 3rd digits(05) = Week of Year

4th digit (3) = Last Lotnumber Digit

PINOUT:

Pin 1 V

Pin 2 GND (Vss)

Pin 3 Output

NOTES:

1.) Controlling dimension: mm

2.) Leads must be free of flash and

plating voids

3.) Leads must not arc toward

the rear of package

4.) Package dimensions exclude

molding flash

5.) Tolerance is 0.254mm unless

otherwise specified

Hall Plate dimension:

0.150x0.150

Max 5o

Typ 5o

0.7 Max

* MARKING:

1&2 Digits (42) = Part Number (90242)

3,4&5 Dgits(951) =Last Lotnumber Digits

42951

1.30

1.00

0.10

0.00

3.10

2.70

3.00

2.60

0.50

0.35

1.80

1.50 chip

0.66

0.56

0.20

MIN

0.25

0.102.10

1.70

0.90

0.70

SOT-23 Hall Plate / Chip LocationSOT-23 Package Dimensions

NOTES:

1.) Controlling dimension: mm

2.) Lead thickness after solder plating will

be 0.254 mm maximum

3.) Package dimensions exclude molding

flash

4.) The end flash shall not exceed 0.127 mm

on each side of package

5.) Tolerance is 0.254mm unless otherwise

specified

PINOUT:

Pin 1 V

Pin 2 Outpout

Pin 3 GND

Bottom View of Package

0.80 +/- 0.15

0 +/- 0.15

MLX90242

Linear Hall Effect Sensor

3901090242 Page 7 of 7 Data Sheet

Rev. 024 Mar/04

All Dimensions in millimeters

VA Hall Plate / Chip Location

VA Package Dimensions

Notes:

1. Pinout: Pin 1 V

Pin 2 n/c

Pin 3 GND

Pin 4 Output

2. Controlling dimension: mm .

3. Leads must be free of flash and plating voids.

4. Leads must not arc toward the rear of package.

5. Package dimensions exclude molding flash.

6. Tolerance: +/- 0.254 mm unless otherwise specified.

9. *Marking:

Line 1:

1st three digits (242) = Part Number

4th and 5th digits (GA) = Revision Number

Line 2:

7 Digits =Lot Number

Back Side Marking =Lot Number

YYWW =DateCode

Hall Plate

0.15 x 0.15

0.387

0.289

Marked

Surface

3.46

3.30

(2x) 5o

(2x)

0.387

0.289

3.79

3.63

H1.0

MAX

0.22

REF

0.45

0.35

4.50

4.10

45o X 1mm

15.50

14.50

242GA

XXXXXXX

1 2 3 4

5.08

5.24

5.33

5.43

1.22

1.32 3.76

3.86

1.20

1.10

0.66

0.61

0.29

0.24

45o

0.31

0.18

0.15

0.0

0.60

0.40

0.35

0.25

45o

Reference (0,0)

MLX 90242

2.40 +/- 0.15

1.88 +/- 0.15

Go to our website at

www.melexis.com

Or for additional information contact Melexis Direct:

Europe and Japan: All other locations:

Phone: +32 13 67 0495 Phone: +1 603 223 2362

E-mail: sales_europe@melexis.com E-mail: sales_usa@melexis.com

QS9000, VDA6.1 and ISO14001 Certified