LT1078/LT1079 Micropower, Dual and Quad, Single Supply, Precision Op Amps DESCRIPTIO U FEATURES Available in 8-Pin SO Package 50A Max Supply Current per Amplifier 70V Max Offset Voltage 180A Max Offset Voltage in 8-Pin SO 250pA Max Offset Current 0.6VP-P, 0.1Hz to 10Hz Voltage Noise 3pAP-P, 0.1Hz to 10Hz Current Noise 0.4V/C Offset Voltage Drift 200kHz Gain Bandwidth Product 0.07V/s Slew Rate Single Supply Operation Input Voltage Range Includes Ground Output Swings to Ground while Sinking Current No Pull-Down Resistors Needed Output Sources and Sinks 5mA Load Current U APPLICATIO S The LT (R) 1078 is a micropower dual op amp in 8-pin packages including the small outline surface mount package. The LT1079 is a micropower quad op amp offered in the standard 14-pin packages. Both devices are optimized for single supply operation at 5V. 15V specifications are also provided. Micropower performance of competing devices is achieved at the expense of seriously degrading precision, noise, speed and output drive specifications. The design effort of the LT1078/LT1079 was concentrated on reducing supply current without sacrificing other parameters. The offset voltage achieved is the lowest on any dual or quad nonchopper stabilized op amp--micropower or otherwise. Offset current, voltage and current noise, slew rate and gain bandwidth product are all two to ten times better than on previous micropower op amps. The 1/f corner of the voltage noise spectrum is at 0.7Hz, at least three times lower than on any monolithic op amp. This results in low frequency (0.1Hz to 10Hz) noise performance which can only be found on devices with an order of magnitude higher supply current. Battery or Solar-Powered Systems Portable Instrumentation Remote Sensor Amplifier Satellite Circuitry Micropower Sample-and-Hold Thermocouple Amplifier Micropower Filters Both the LT1078 and LT1079 can be operated from a single supply (as low as one lithium cell or two Ni-Cad batteries). The input range goes below ground. The allNPN output stage swings to within a few millivolts of ground while sinking current--no power consuming pull down resistors are needed. , LTC and LT are registered trademarks of Linear Technology Corporation. U TYPICAL APPLICATIO Single Battery, Micropower, Gain = 100, Instrumentation Amplifier 10.1k Distribution of Input Offset Voltage (LT1078 and LT1079 in H, J, N Packages) 16 1M 14 1M INVERTING INPUT 2 3 - - A 1/2 LT1078 3V (LITHIUM CELL) 1 10.1k 6 + 5 NONINVERTING INPUT + TYPICAL PERFORMANCE INPUT OFFSET VOLTAGE = 40V INPUT OFFSET CURRENT = 0.2nA TOTAL POWER DISSIPATION = 240W COMMON MODE REJECTION = 110dB (AMPLIFIER LIMITED) GAIN BANDWIDTH PRODUCT = 200kHz - B 1/2 LT1078 + 4 7 VS = 5V, 0V TA = 25C 12 8 OUT LT1078/79 * TA01 OUTPUT NOISE = 85VP-P 0.1Hz TO 10Hz = 300VRMS OVER FULL BANDWIDTH INPUT RANGE = 0.03V TO 1.8V OUTPUT RANGE = 0.03V TO 2.3V (0.3mV VIN+ - VIN- 23mV) OUTPUTS SINK CURRENT--NO PULL-DOWN RESISTORS ARE NEEDED PERCENT OF UNITS 10 8 6 4 2 0 -120 -80 -40 40 80 0 INPUT OFFSET VOLTAGE (V) 120 1078/79 * TA02 10789fe 1 LT1078/LT1079 W W U W ABSOLUTE MAXIMUM RATINGS (Note 1) Supply Voltage ...................................................... 22V Differential Input Voltage ....................................... 30V Input Voltage ............... Equal to Positive Supply Voltage ............5V Below Negative Supply Voltage Output Short-Circuit Duration .......................... Indefinite Storage Temperature Range All Grades ......................................... - 65C to 150C Operating Temperature Range LT1078AM/LT1078M/ LT1079AM/LT1079M (OBSOLETE) ..... - 55C to 125C LT1078I/LT1079I .................................... - 40C to 85C LT1078AC/LT1078C/LT1078S8/ LT1079AC/LT1079C .................................... 0C to 70C Lead Temperature (Soldering, 10 sec).................. 300C W U U PACKAGE/ORDER INFORMATION TOP VIEW V OUT A 1 8 7 OUT B OUT A 1 A -IN A 2 B -IN A 2 8 +IN A 3 6 -IN B 4 OUT B 6 -IN B 5 +IN B LT1078ACH LT1078MH OBSOLETE PACKAGES 14 OUT D OUT A 1 A D ORDER PART NUMBER 13 -IN D 12 +IN D +IN A 3 11 V - 4 10 +IN C +IN B 5 B C V+ 5 OUT B ORDER PART NUMBER LT1078IS8 LT1078S8 PART MARKING 1078 TOP VIEW OUT A 1 16 OUT D A D +IN A 3 V+ 4 -IN C -IN B 6 OUT C OUT B 7 NC 8 15 -IN D 14 +IN D 13 V- +IN B 5 8 J PACKAGE 14-LEAD CERAMIC DIP TJMAX = 150C, JA = 100C/ W (J) OUT A 6 TJMAX = 110C, JA = 220C/ W 9 N PACKAGE 14-LEAD PDIP TJMAX = 110C, JA = 130C/ W (N) 7 NOTE: THIS PIN CONFIGURATION DIFFERS FROM THE 8-LEAD DIP PIN LOCATIONS. INSTEAD, IT FOLLOWS THE INDUSTRY STANDARD LT1013DS8 SO PACKAGE CONFIGURATION. FOR SIMILAR PERFORMANCE WITH TRADITIONAL DIP PINOUT, SEE THE LT2078 -IN A 2 LT1079ACN LT1079CN LT1079IN -IN A B LT1078AMJ8 LT1078MJ8 Consider the N8 and S8 Packages for Alternate Source 8 S8 PACKAGE 8-LEAD PLASTIC SO J8 PACKAGE 8-LEAD PDIP TJMAX = 150C, JA = 100C/ W (J8) TOP VIEW 2 -IN B 4 LT1078ACN8 LT1078CN8 LT1078IN8 ORDER PART NUMBER A +IN B 3 ORDER PART NUMBER TJMAX = 150C, JA = 150C/ W, JC = 45C/ W -IN B 6 V- N8 PACKAGE 8-LEAD PDIP TJMAX = 100C, JA = 130C/ W (N8) V - (CASE) H PACKAGE 8-LEAD TO-5 METAL CAN OUT B 7 B +IN A 1 V+ 5 +IN B +IN A 3 V+ 7 A V- 4 -IN A 2 TOP VIEW TOP VIEW + ORDER PART NUMBER LT1079ISW LT1079SW 12 +IN C B C 11 -IN C 10 OUT C 9 NC SW PACKAGE 16-LEAD PLASTIC SO WIDE LT1079MJ NOTE: FOR 14-PIN NARROW PACKAGE SEE THE LT2079 TJMAX = 110C, JA = 150C/ W OBSOLETE PACKAGE Consider the N Packages for Alternate Source 10789fe 2 LT1078/LT1079 ELECTRICAL CHARACTERISTICS SYMBOL PARAMETER VOS Input Offset Voltage VS = 5V, 0V, VCM = 0.1V, VO = 1.4V, TA = 25C unless otherwise noted. CONDITIONS (NOTE 2) LT1078AC/LT1079AC LT1078AM/LT1079AM MIN TYP MAX LT1078 LT1078IS8/LT1078S8 LT1079 LT1079ISW/LT1079SW 30 70 35 100 LT1078C/LT1079C LT1078I/LT1079I LT1078M/LT1079M LT1078S8/LT1079SW MIN TYP MAX 40 60 40 60 120 180 150 300 UNITS V V V V VOS Time Long Term Input Offset Voltage Stability 0.4 IOS Input Offset Current 0.05 0.25 0.05 0.35 nA IB Input Bias Current 6 8 6 10 nA en Input Noise Voltage 0.1Hz to 10Hz (Note 3) 0.6 1.2 0.6 VP-P Input Noise Voltage Density fO = 10Hz (Note 3) fO = 1000Hz (Note 3) 29 28 45 37 29 28 nVHz nVHz Input Noise Current 0.1Hz to 10Hz (Note 3) 2.3 4.0 2.3 pAP-P Input Noise Current Density fO = 10Hz (Note 3) fO = 1000Hz 0.06 0.02 0.10 0.06 0.02 pAHz pAHz Input Resistance Differential Mode Common Mode (Note 4) in V/Mo 0.5 400 800 6 300 800 6 M G Input Voltage Range 3.5 0 3.8 - 0.3 3.5 0 3.8 - 0.3 V V CMRR Common Mode Rejection Ratio VCM = 0V to 3.5V 97 110 94 108 dB PSRR Power Supply Rejection Ratio VS = 2.3V to 12V 102 114 100 114 dB AVOL Large-Signal Voltage Gain VO = 0.03V to 4V, No Load VO = 0.03V to 3.5V, RL = 50k 200 150 1000 600 150 120 1000 600 V/mV V/mV Maximum Output Voltage Swing Output Low, No Load Output Low, 2k to GND Output Low, ISINK = 100A 3.5 0.55 95 6 1.0 130 3.5 0.55 95 6 1.0 130 mV mV mV Output High, No Load Output High, 2k to GND 4.2 3.5 4.4 3.9 4.2 3.5 4.4 3.9 V V 0.04 0.07 0.04 0.07 V/s 200 kHz SR Slew Rate AV = 1, VS = 2.5V GBW Gain Bandwidth Product fO 20kHz IS Supply Current per Amplifier 200 38 Channel Separation VIN = 3V, RL = 10k 130 Minimum Supply Voltage (Note 5) 2.2 50 39 55 130 2.3 2.2 A dB 2.3 V 10789fe 3 LT1078/LT1079 ELECTRICAL CHARACTERISTICS The denotes the specifications which apply over the temperature range - 40C TA 85C for I grades, - 55C TA 125C for AM/M grades. VS = 5V, 0V, VCM = 0.1V, VO = 1.4V unless otherwise noted. SYMBOL PARAMETER VOS Input Offset Voltage VOS T Input Offset Voltage Drift (Note 6) IOS Input Offset Current LT1078I/LT1079I LT1078AM/LT1079AM LT1078M/LT1079M MIN TYP MAX MIN TYP MAX CONDITIONS UNITS LT1078 LT1078IS8/LT1079 LT1079ISW 70 80 250 280 95 100 100 370 400 560 V V V 0.4 1.8 LT1078IS8 LT1079ISW 0.5 0.6 0.7 2.5 3.5 4.0 V/C V/C V/C 0.07 0.50 LT1078I/LT1079I 0.07 0.1 0.70 1.0 nA nA 7 10 7 12 nA IB Input Bias Current CMRR Common Mode Rejection Ratio VCM = 0.05V to 3.2V 92 106 88 104 dB PSRR Power Supply Rejection Ratio VS = 3.1V to 12V 98 110 94 110 dB AVOL Large-Signal Voltage Gain VO = 0.05V to 4V, No Load VO = 0.05V to 3.5V, RL = 50k 110 80 600 400 80 60 600 400 V/mV V/mV Maximum Output Voltage Swing Output Low, No Load Output Low, ISINK = 100A Output High, No Load Output High, 2k to GND IS Supply Current per Amplifier 4.5 125 3.9 3.0 4.2 3.7 43 8 170 4.5 125 3.9 3.0 60 8 170 4.2 3.7 45 mV mV V V 70 A The denotes the specifications which apply over the temperature range 0C TA 70C. VS = 5V, 0V, VCM = 0.1V, VO = 1.4V unless otherwise noted. SYMBOL PARAMETER LT1078C/LT1079C LT1078AC/LT1079AC LT1078S8/LT1079SW MIN TYP MAX MIN TYP MAX CONDITIONS UNITS LT1078 LT1079 LT1078S8 LT1079SW 50 60 150 180 60 70 85 90 240 270 350 480 V V V V 0.4 1.8 LT1078S8 LT1079SW 0.5 0.6 0.7 2.5 3.5 4.0 V/C V/C V/C Input Offset Current 0.06 0.35 0.06 0.50 nA IB Input Bias Current 6 9 6 11 nA CMRR Common Mode Rejection Ratio VCM = 0V to 3.4V 94 108 90 106 dB PSRR Power Supply Rejection Ratio VS = 2.6V to 12V 100 112 97 112 dB AVOL Large-Signal Voltage Gain VO = 0.05V to 4V, No Load VO = 0.05V to 3.5V, RL = 50k 150 110 750 500 110 80 750 500 V/mV V/mV Maximum Output Voltage Swing Output Low, No Load Output Low, ISINK = 100A Output High, No Load Output High, 2k to GND VOS Input Offset Voltage VOS T Input Offset Voltage Drift (Note 6) IOS IS Supply Current per Amplifier 4.0 105 4.1 3.3 7 150 4.3 3.8 40 4.0 105 4.1 3.3 55 7 150 4.3 3.8 42 mV mV V V 63 A 10789fe 4 LT1078/LT1079 ELECTRICAL CHARACTERISTICS SYMBOL PARAMETER VOS Input Offset Voltage IOS Input Offset Current IB Input Bias Current VS = 15V, TA = 25C unless otherwise noted. LT1078AC/LT1079AC LT1078AM/LT1079AM MIN TYP MAX CONDITIONS (Including LT1078IS8/LT1078S8) LT1079ISW/LT1079SW Input Voltage Range LT1078C/LT1079C LT1078I/LT1079I LT1078M/LT1079M LT1078S8/LT1079SW MIN TYP MAX UNITS 50 250 70 80 350 500 V V 0.05 0.25 0.05 0.35 nA 6 8 6 10 nA 13.5 -15.0 13.8 -15.3 13.5 -15.0 13.8 -15.3 V V 100 114 97 114 dB CMRR Common Mode Rejection Ratio VCM = 13.5V, -15V PSRR Power Supply Rejection Ratio VS = 5V, 0V to 18V 102 114 100 114 dB AVOL Large-Signal Voltage Gain VO = 10V, RL = 50k VO = 10V, RL = 2k 1000 400 5000 1100 1000 300 5000 1100 V/mV V/mV VOUT Maximum Output Voltage Swing RL = 50k RL = 2k 13.0 11.0 14.0 13.2 13.0 11.0 14.0 13.2 V V SR Slew Rate 0.06 0.10 0.06 0.10 V/s IS Supply Current per Amplifier 46 65 47 A 75 The denotes the specifications which apply over the temperature range - 40C TA 85C for I grades, - 55C TA 125C for AM/M grades. VS = 15V unless otherwise noted. SYMBOL PARAMETER VOS Input Offset Voltage VOS T Input Offset Voltage Drift (Note 6) IOS Input Offset Current LT1078I/LT1079I LT1078AM/LT1079AM LT1078M/LT1079M MIN TYP MAX MIN TYP MAX CONDITIONS UNITS (Including LT1078IS8) LT1079ISW 90 430 120 130 600 825 V V 0.5 1.8 LT1078IS8 LT1079ISW 0.6 0.7 0.8 2.5 3.8 5.0 V/C V/C V/C 0.07 0.50 LT1078I/LT1079I 0.07 0.1 0.70 1.0 nA nA 7 10 7 12 nA IB Input Bias Current AVOL Large-Signal Voltage Gain VO = 10V, RL = 5k 200 700 150 700 V/mV CMRR Common Mode Rejection Ratio VCM = 13V, -14.9V 94 110 90 110 dB PSRR Power Supply Rejection Ratio 98 110 94 110 dB Maximum Output Voltage Swing RL = 5k 11.0 13.5 11.0 13.5 V Supply Current per Amplifier IS VS = 5V, 0V to 18V 52 80 54 95 A 10789fe 5 LT1078/LT1079 ELECTRICAL CHARACTERISTICS 0C TA 70C. VS = 15V unless otherwise noted. SYMBOL PARAMETER VOS The denotes the specifications which apply over the temperature range LT1078AC/LT1079AC MIN TYP MAX CONDITIONS LT1078C/LT1079C LT1078S8/LT1079SW MIN TYP MAX UNITS 70 330 LT1078S8 LT1079SW 90 100 115 460 540 750 V V V 0.5 1.8 LT1078S8 LT1079SW 0.6 0.7 0.8 2.5 3.8 5.0 V/C V/C V/C Input Offset Voltage VOS T Input Offset Voltage Drift (Note 6) IOS Input Offset Current 0.06 0.35 0.06 0.50 nA IB Input Bias Current 6 9 6 11 nA AVOL Large-Signal Voltage Gain VO = 10V, RL = 5k CMRR Common Mode Rejection Ratio VCM = 13V, -15V 97 112 94 112 dB PSRR Power Supply Rejection Ratio VS = 5V, 0V to 18V 100 112 97 112 dB Maximum Output Voltage Swing RL = 5k 11.0 13.6 11.0 13.6 V IS Supply Current per Amplifier Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Note 2: Typical parameters are defined as the 60% yield of parameter distributions of individual amplifiers, i.e., out of 100 LT1079s (or 100 LT1078s) typically 240 op amps (or 120) will be better than the indicated specification. Note 3: This parameter is tested on a sample basis only. All noise parameters are tested with VS = 2.5V, VO = 0V. 300 1200 49 250 73 1200 50 V/mV A 85 Note 4: This parameter is guaranteed by design and is not tested. Note 5: Power supply rejection ratio is measured at the minimum supply voltage. The op amps actually work at 1.8V supply but with a typical offset skew of -300V. Note 6: This parameter is not 100% tested. 10789fe 6 LT1078/LT1079 U W TYPICAL PERFORMANCE CHARACTERISTICS Input Bias and Offset Currents vs Temperature VS = 15V 45 100 -5 Input Bias Current vs Common Mode Voltage 0 VS = 5V, 0V TO 15V VS = 5V, 0V -2 IOS 50 INPUT BIAS CURRENT (nA) 50 OFFSET CURRENT (pA) SUPPLY CURRENT PER AMPLIFIER (A) 55 BIAS CURRENT (nA) Supply Current vs Temperature 0 40 VS = 5V, 0V 35 30 25 -50 -25 50 25 75 0 TEMPERATURE (C) 100 IB -6 TA = 25C -6 TA = 125C -8 -10 -12 -7 -50 -25 125 TA = -55C -4 50 0 75 25 TEMPERATURE (C) 100 -1 125 LT1078/79 * TPC03 LT1078/79 * TPC02 LT1078/79 * TPC01 0.1Hz to 10Hz Noise 4 0 1 2 3 COMMON MODE VOLTAGE (V) 0.01Hz to 10Hz Noise Noise Spectrum 1000 CHANNEL B VOLTAGE NOISE DENSITY (nV/Hz) CURRENT NOISE DENSITY (fA/Hz) TA = 25C VS = 2.5V CHANNEL A NOISE VOLTAGE (0.4V/DIV) NOISE VOLTAGE (0.4V/DIV) TA = 25C VS = 2.5V CHANNEL A 0.4V CHANNEL B 2 6 4 TIME (SEC) 8 20 0 10 60 40 TIME (SEC) 80 20 PERCENT OF UNITS PERCENT OF UNITS 20 106 LT1078'S 45 LT1079'S 15 10 35 30 VOLTAGE NOISE DENSITY (nV/Hz) 1/f CORNER 0.7Hz 40 LT1078/79 * TPC07 1 100 10 FREQUENCY (Hz) 15 10 0 1000 Long Term Stability of Two Representative Units (LT1078) 15 120 VS = 5V, 0V 109 VCM = 0.1V 120 LT1078'S 70 LT1079'S 89 520 OP AMPS 85 44 47 5 5 0 25 30 LT1078/79 * TPC06 25 35 25 VOLTAGE NOISE Distribution of Offset Voltage Drift with Temperature (In All Packages Except Surface Mount) 10Hz Voltage Noise Distribution 30 100 LT1078/79 * TPC05 LT1078/79 * TPC04 TA = 25C VS = 2.5V 329 OP AMPS TESTED FROM THREE RUNS CURRENT NOISE 10 0.1 100 OFFSET VOLTAGE CHANGE (V) 0 300 TA = 25C VS = 2.5V (AT VS = 15V VOLTAGE NOISE IS 4% LESS CURRENT NOISE IS UNCHANGED) 1 7 3 5 4 3 1 1 1 -2 -1 0 1 2 OFFSET VOLTAGE DRIFT WITH TEMPERATURE (V/C) LT1078/79 * TPC08 TA = 25C, VS = 5V, 0V VCM = 0.1V 10 1A 5 0 2B -5 1B -10 2A -15 0 1 2 3 TIME (MONTHS) 4 5 LT078/79 * TPC09 10789fe 7 LT1078/LT1079 U W TYPICAL PERFORMANCE CHARACTERISTICS Voltage Gain vs Frequency Gain, Phase vs Frequency 140 30 VS = 5V, 0V 40 15V 5V, 0V GAIN 10 20 140 PHASE MARGIN 54 160 5V, 0V 0 100 10 100 1k 10k 100k 1M FREQUENCY (Hz) 10 30 AV = 1 60 AV = 5 40 AV = 10 20 0 -10 1 80 200 TA = 25C CL = 20pF -20 0.01 0.1 100 300 FREQUENCY (kHz) 10 1000 100 1000 CAPACITIVE LOAD (pF) 10000 LT1078/79 * TPC12 LT1078/79 * TPC10 LTC1078/79 TPC11 Slew Rate, Gain Bandwidth Product and Phase Margin vs Temperature Large-Signal Transient Response VS = 5V, 0V Large-Signal Transient Response VS = 15V 0.12 SLEW = 15V 0.10 SLEW = 5V, 0V M = 15V 0.04 70 M = 5V, 0V 60 50 240 GBW = 15V 220 40 5V/DIV 80 0.06 1V/DIV 0.08 PHASE MARGIN (DEG) SLEW RATE (V/s) 180 15V 0 TA = 25C VS = 5V, 0V 120 PHASE SHIFT (DEG) VOLTAGE GAIN (dB) 20 80 60 100 OVERSHOOT (%) VS = 15V 100 VOLTAGE GAIN (dB) PHASE MARGIN 66 TA = 25C 120 GAIN BANDWIDTH PRODUCT (kHz) Capacitive Load Handling 120 0V 0V 200 180 fO = 20kHz 160 -50 -25 AV = 1 NO LOAD AV = 1, NO LOAD 50s/DIV INPUT PULSE 0V TO 3.8V GBW = 5V, 0V 100s/DIV LT1078/79 * TPC28 LT1078/79 * TPC27 50 0 75 25 TEMPERATURE (C) 100 125 LT1078/79 * TPC13 Minimum Supply Voltage Warm-Up Drift 125C -100 70C -200 0C 25C -300 -55C NONFUNCTIONAL -400 -500 0 2 3 1 POSITIVE SUPPLY VOLTAGE (V) LT1078/79 * TPC16 TA = 25C VS = 15V WARM UP DRIFT AT VS = 5V, 0V IS IMMEASURABLY LOW 0.7 0.6 0.5 0.4 0.3 VS = 15V VS = 5V, 0V 125C VOLTAGE GAIN (V/V) V - = 0V -0.1V VCM 0.4V 0 Voltage Gain vs Load Resistance 10M 0.8 CHANGE IN OFFSET VOLTAGE (V) INPUT OFFSET VOLTAGE (V) 100 LT1079 1M 25C -55C -55C 25C 125C 0.2 LT1078 0.1 0 0 1 2 3 TIME AFTER POWER-ON (MINUTES) LT1078/79 * TPC17 100k 100 1k 10k 100k LOAD RESISTANCE TO GROUND () 1M LT1078/79 * TPC18 10789fe 8 LT1078/LT1079 U W TYPICAL PERFORMANCE CHARACTERISTICS Output Saturation vs Temperature vs Sink Current Output Voltage Swing vs Load Current V+ 1000 16 ISINK = 2mA ISINK = 10A VS = 5V, 0V ISINK = 1A 10 NO LOAD -55C + V -2 V- + 2 125C V- + 1 12 10 8 6 4 25C 2 RL = 5k TO GND 1 -50 -25 TA = 25C VS = 5V, 0V 14 V+ - 1 PERCENT OF UNITS ISINK = 1mA ISINK = 100A 100 25C 125C OUTPUT VOLTAGE SWING (V) SATURATION VOLTAGE (mV) Distribution of Input Offset Voltage (LT1078 in 8-Pin SO Package) V 0 25 50 75 TEMPERATURE (C) 100 -55C - 0 40 80 120 160 -160 -120 -80 -40 0 INPUT OFFSET VOLTAGE (V) 0.01 0.1 1 10 SOURCING OR SINKING LOAD CURRENT (mA) 125 LT1078/79 * TPC20 LT1078/79 * TPC19 LT1078/79 * TPC21 V+ - 1 V+ - 2 V- + 1 V- V- - 1 -50 -25 0 25 50 75 TEMPERATURE (C) 100 125 Closed Loop Output Impedance VS = 15V RL 100k 5 VS = 5V, 0V RL 100k 20 VS = 5V, 0V RL 1k 4 VS = 15V RL = 30k 3 10 2 TA = 25C LOAD RL, TO GND 0 0.01 1 0 100 1 10 FREQUENCY (kHz) 1k OUTPUT IMPEDANCE () COMMON MODE RANGE (V) V + = 2.5V TO 18V V - = 0V TO -18V 30 PEAK-TO-PEAK OUTPUT SWING, VS = 5V, 0V (V) V+ Undistorted Output Swing vs Frequency PEAK-TO-PEAK OUTPUT SWING, VS = 15V (V) Common Mode Range vs Temperature AV = 100 100 AV = 10 10 AV = 1 1 0.1 10 100 1k 10k FREQUENCY (Hz) LT1078/79 * TPC23 LT1078/79 * TPC24 LT1078/79 * TPC22 Common Mode Rejection Ratio vs Frequency Power Supply Rejection Ratio vs Frequency 100 VS = 15V 80 VS = 5V, 0V 60 40 20 0 10 100 1k 10k FREQUENCY (Hz) 100k 1M LT1078/79 * TPC25 Channel Separation vs Frequency 120 140 100 120 80 NEGATIVE SUPPLY 60 CHANNEL SEPARATION (dB) TA = 25C POWER SUPPLY REJECTION RATIO (dB) COMMON MODE REJECTION RATIO (dB) 120 POSITIVE SUPPLY 40 20 0 0.1 100k 100 80 60 40 TA = 25C VS = 2.5V VIN = 3VP-P TO 2kHz RL = 10k 20 TA = 25C VS = 2.5V + 1VP-P SINE WAVE 0 1 10 100 1k 10k FREQUENCY (Hz) 100k 1M LT1078/79 * TPC26 1 10 10k 1k 100 FREQUENCY (Hz) 100k 1M LT1078/79 * TPC27 10789fe 9 LT1078/LT1079 U W TYPICAL PERFORMANCE CHARACTERISTICS Small-Signal Transient Response VS = 5V, 0V 20mV/DIV 20mV/DIV Small-Signal Transient Response VS = 2.5V 0.1V AV = 1 10s/DIV CL = 15pF INPUT 50mV TO 150mV 0V AV = 1 CL = 15pF LT1078/79 * TPC24 10s/DIV LT1078/79 * TPC25 20mV/DIV Small-Signal Transient Response VS = 15V 0V AV = 1 CL = 15pF 10s/DIV LT1078/79 * TPC26 U W U U APPLICATIONS INFORMATION The LT1078/LT1079 devices are fully specified with V + = 5V, V - = 0V, VCM = 0.1V. This set of operating conditions appears to be the most representative for battery-powered micropower circuits. Offset voltage is internally trimmed to a minimum value at these supply voltages. When 9V or 3V batteries or 2.5V dual supplies are used, bias and offset current changes will be minimal. Offset voltage changes will be just a few microvolts as given by the PSRR and CMRR specifications. For example, if PSRR = 114dB (= 2V/V), at 9V the offset voltage change will be 8V. Similarly, VS = 2.5V, VCM = 0V is equivalent to a common mode voltage change of 2.4V or a VOS change of 7V if CMRR = 110dB (3V/V). A full set of specifications is also provided at 15V supply voltages for comparison with other devices and for completeness. Single Supply Operation The LT1078/LT1079 are fully specified for single supply operation, i.e., when the negative supply is 0V. Input common mode range goes below ground and the output swings within a few millivolts of ground while sinking current. All competing micropower op amps either cannot swing to within 600mV of ground (OP-20, OP-220, OP-420) or need a pull-down resistor connected to the output to swing to ground (OP-90, OP-290, OP-490, HA5141/42/44). This 10789fe 10 LT1078/LT1079 U W U U APPLICATIONS INFORMATION difference is critical because in many applications these competing devices cannot be operated as micropower op amps and swing to ground simultaneously. As an example, consider the instrumentation amplifier shown on the front page. When the common mode signal is low and the output is high, amplifier A has to sink current. When the common mode signal is high and the output low, amplifier B has to sink current. The competing devices require a 12k pull-down resistor at the output of amplifier A and a 15k at the output of B to handle the specified signals. (The LT1078 does not need pull-down resistors.) When the common mode input is high and the output is high these pull-down resistors draw 300A (150A each), which is excessive for micropower applications. The instrumentation amplifier is by no means the only application requiring current sinking capability. In seven of the nine single supply applications shown in this data sheet the op amps have to be able to sink current. In two of the applications the first amplifier has to sink only the 6nA input bias current of the second op amp. The competing devices, however, cannot even sink 6nA without a pulldown resistor Since the output of the LT1078/LT1079 cannot go exactly to ground, but can only approach ground to within a few millivolts, care should be exercised to ensure that the output is not saturated. For example, a 1mV input signal will cause the amplifier to set up in its linear region in the gain 100 configuration shown in Figure 1a, but is not enough to make the amplifier function properly in the voltage follower mode, Figure 1b. 5V 5V R - 99R 100mV + 1mV LT1078/79 * F01a Figure 1a. Gain 100 Amplifier LT1078/79 * F01b Figure 1b. Voltage Follower 2. When the input is more than 400mV below ground (at 25C), the input stage saturates and phase reversal occurs at the output. This can cause lockup in servo systems. Due to a unique phase reversal protection circuitry, the LT1078/LT1079 output does not reverse, as illustrated in Figure 2, even when the inputs are at -1V. 4V 2V 2V 2V 0V 0V 0V 1ms/DIV OP-90 EXHIBITS OUTPUT PHASE REVERSAL LT1078/79 * F02a + 1. When the input is more than a diode drop below ground, unlimited current will flow from the substrate (V - terminal) to the input. This can destroy the unit. On the LT1078/LT1079, resistors in series with the input protect the devices even when the input is 5V below ground. 4V 1ms/DIV 1mV OUTPUT SATURATED 3.5mV Single supply operation can also create difficulties at the input. The driving signal can fall below 0V -- inadvertently or on a transient basis. If the input is more than a few hundred millivolts below ground, two distinct problems can occur on previous single supply designs, such as the LM124, LM158, OP-20, OP-21, OP-220, OP-221, OP-420 (1 and 2), OP-90/290/490 (2 only): 4V 6VP-P INPUT -1V TO 5V - 1ms/DIV LT1078/LT1079 NO PHASE REVERSAL LT1078/79 * F02b LT1078/79 * F02C Figure 2. Voltage Follower with Input Exceeding the Negative Common Mode Range (VS = 5V, 0V) 10789fe 11 LT1078/LT1079 U W U U APPLICATIONS INFORMATION Matching Specifications In many applications the performance of a system depends on the matching between two op amps, rather than the individual characteristics of the two devices. The two and three op amp instrumentation amplifier configurations shown in this data sheet are examples. Matching characteristics are not 100% tested on the LT1078/LT1079. Some specifications are guaranteed by definition. For example, 70V maximum offset voltage implies that mismatch cannot be more than 140V. 97dB (= 14V/V) CMRR means that worst-case CMRR match is 91dB (= 28V/V). However, Table 1 can be used to estimate the expected matching performance at VS = 5V, 0V between the two sides of the LT1078, and between amplifiers A and D, and between amplifiers B and C of the LT1079. Table 1 PARAMETER VOS Match, VOS LT1078 LT1079 Temperature Coefficient VOS Average Noninverting IB Match of Noninverting IB CMRR Match PSRR Match LT1078AC/LT1079AC/LT1078AM/LT1079AM 50% YIELD 98% YIELD 30 110 40 150 0.5 1.2 6 8 0.12 0.4 120 100 117 105 LT1078C/LT1079C/LT1078M/LT1079M 50% YIELD 98% YIELD 50 190 50 250 0.6 1.8 6 10 0.15 0.5 117 97 117 102 UNITS V V V/C nA nA dB dB Comparator Applications The single supply operation of the LT1078/LT1079 and its ability to swing close to ground while sinking current lends itself to use as a precision comparator with TTL compatible output. 4 OUTPUT (V) 2 2 0 0 0 100 -100 INPUT (mV) INPUT (mV) OUTPUT (V) 4 VS = 5V, 0V 200s/DIV 0 VS = 5V, 0V 200s/DIV LT2078/79 * F03 LT2078/79 * F04 Figure 3. Comparator Rise Response Time to 10mV, 5mV, 2mV Overdrives Figure 4. Comparator Fall Response Time to 10mV, 5mV, 2mV Overdrives 10789fe 12 LT1078/LT1079 U TYPICAL APPLICATIONS Micropower, 10ppm/C, 5V Reference 2M LT1034BC-1.2 Gain of 10 Difference Amplifier 10M 9V 3V 220k 5.000VOUT 120k 3 + - 1M - -IN 8 1/2 LT1078 2 1M 1 510k 4 -9V 1M 6 7 -5.000VOUT + OUTPUT 0.0035V TO 2.4V + +IN - 1/2 LT1078 5 1/2 LT1078 1M LT1078/79 * TA04 10M LT1078/79 * TA03 510k 1% BANDWIDTH= 20kHz OUTPUT OFFSET= 0.7mV OUTPUT NOISE= 80VP-P (0.1Hz TO 10Hz) 260VRMS OVER FULL BANDWIDTH 20k 160k 1% SUPPLY CURRENT = 9V BATTERY = 115A -9V BATTERY = 85A OUTPUT NOISE = 36VP-P, 0.1Hz TO 10Hz THE USEFULNESS OF DIFFERENCE AMPLIFIERS IS LIMITED BY THE FACT THAT THE INPUT RESISTANCE IS EQUAL TO THE SOURCE RESISTANCE. THE PICOAMPERE OFFSET CURRENT AND LOW CURRENT NOISE OF THE LT1078 ALLOWS THE USE OF 1M SOURCE RESISTORS WITHOUT DEGRADATION IN PERFORMANCE. IN ADDITION, WITH MEGOHM RESISTORS MICROPOWER OPERATION CAN BE MAINTAINED THE LT1078 CONTRIBUTES LESS THAN 3% OF THE TOTAL OUTPUT NOISE AND DRIFT WITH TIME AND TEMPERATURE. THE ACCURACY OF THE -5V OUTPUT DEPENDS ON THE MATCHING OF THE TWO 1M RESISTORS Picoampere Input Current, Triple Op Amp Instrumentation Amplifier with Bias Current Cancellation 3 -IN + 1/4 LT1079 2 1 R2 1M R1 1M - 2R 20M R3 9.1M RG 200k 9 6 - 1/4 LT1079 5 +IN R 10M 12 2R 20M + + 9V 4 - 11 14 - 1/4 LT1079 10 R2 1M 1/4 LT1079 13 7 R1 1M + 8 OUTPUT 4mV TO 8.2V LT1078/79 * TA05 R3 9.1M ( ) GAIN = 1 + 2R1 R3 = 100 FOR VALUES SHOWN RG R2 INPUT BIAS CURRENT TYPICALLY < 150pA INPUT RESISTANCE = 3R = 30M FOR VALUES SHOWN NEGATIVE COMMON MODE LIMIT = (IB)(2R) + 20mV 140mV GAIN BANDWIDTH PRODUCT = 1.8MHz 10789fe 13 LT1078/LT1079 U TYPICAL APPLICATIONS 85V, -100V Common Mode Range Instrumentation Amplifier (AV = 10) Half-Wave Rectifier 2M 1M 9V 10M +IN 10M -IN 2 - 10M 1/2 LT1078 3 + 1M 3V 2M 8 - INPUT 100k 1 100k 4 6 - 1/2 LT1078 5 -9V 7 + OUTPUT 1/2 LT1078 1M OUTPUT 8V TO -9V + VOMIN = 6mV NO DISTORTION TO 100Hz LT1078/79 * TA06 1.8V BANDWIDTH= OUTPUT OFFSET= OUTPUT NOISE= = 2kHz 8mV 0.8mVP-P (0.1Hz TO 10Hz) 1.4mVRMS OVER FULL BANDWIDTH (DOMINATED BY RESISTOR NOISE) INPUT RESISTANCE = 10M 1.8V 0V -1.8V LT1078/79 * TA07 Absolute Value Circuit (Full-Wave Rectifier) 200k 200k INPUT 2 5V 3.5V 8 0V - 1/2 LT1078 3 3.5V 1 5 1N4148 + + 7 1/2 LT1078 4 6 OUTPUT - -3.5V LT1078/79 * TA08 VOMIN = 4mV NO DISTORTION TO 100Hz Programmable Gain Amplifier (Single Supply) 1.11k 10k 100k 1M 3V TO 18V 2 - 1/4 LT1079 3 + 3V TO 18V 11 4 11 1 1 6 2 - 1/4 LT1079 5 13 A 7 + 9 10 ERROR DUE TO SWITCH ON RESISTANCE, LEAKAGE CURRENT, NOISE AND TRANSIENTS ARE ELIMINATED 1/4 LT1079 12 + - + C 8 8 7 CD4016B 13 5 6 GAIN 1000 100 10 14 OUT LT1078/79 * TA09 9 1/4 LT1079 IN 4 3 B - PIN 13 HIGH LOW LOW CD4016B PIN 5 LOW HIGH LOW PIN 6 LOW LOW HIGH 10789fe 14 LT1078/LT1079 U TYPICAL APPLICATIONS Single Supply, Micropower, Second Order Lowpass Filter with 60Hz Notch 0.02F 27.6k 0.1% 27.6k 0.1% 3 IN + 0.01F 6 5V 8 1 1/2 LT1078 2 - 2.64M 0.1% 2.64M 0.1% - 7 1/2 LT1078 5 + OUTPUT TYPICAL OFFSET 600V 2000pF 0.5% 4 5.1M 1% 120k 5% 1.35M 0.1% 100pF 1000pF 0.5% 1000pF 0.5% fC = 40Hz Q > 30 LT1078/79 * TA10 Micropower Multiplier/Divider 505k 0.1% 505k 0.1% - 220pF 4 1/4 LT1079 5 30k 5% 11 Z INPUT (5mV TO 50V) 220pF Q3 30k 5% 7 + Q1 14 10k GAIN 499k 0.5% 13 1/4 LT1079 + 9V 6 - Y INPUT (5mV TO 50V) 12 -1.5V TO -9V X INPUT (5mV TO 50V) 505k 0.1% 2 - + - 10 + 220pF Q2 1/4 LT1079 3 9 Q4 1/4 LT1079 8 OUTPUT (5mV TO 8V) 1 30k 5% LT1078/79 * TA11 Q1,Q2, Q3, Q4 = MAT-04 TYPICAL LINEARITY = 0.01% OF FULL-SCALE OUTPUT (X)(Y) OUTPUT = , POSITIVE INPUTS ONLY (Z) X + Y+ Z + OUT 500k OUT POSITIVE SUPPLY CURRENT = 165A + 500k NEGATIVE SUPPLY CURRENT = 165A + BANDWIDTH (< 3VP-P SIGNAL): X AND Y INPUTS = 10kHz Z INPUT = 4kHz 10789fe 15 LT1078/LT1079 U TYPICAL APPLICATIONS Micropower Dead Zone Generator Q4 1M** 2 INPUT VSET DEAD ZONE CONTROL INPUT 0.4V TO 5V 1M* 1M** - Q2 Q3 1 470k 1/4 LT1079 510k 3 + 1M* Q1 2N4393 9 1M** GAIN 200k - 8 1M 1M** 13 - 510k 12 + 1/4 LT1079 1N914 10 + 1/4 LT1079 14 VOUT LT1078/79 * TA12 9V 6 - 1M 4 + 1N914 Q6 2N4393 VSET VOUT 1000pF 7 1/4 LT1079 5 680k 510k 1M Q5 11 -9V VIN BIPOLAR SYMMETRY IS EXCELLENT VSET BECAUSE ONE DEVICE, Q2, * 1% FILM SETS BOTH LIMITS ** RATIO MATCH 0.05% SUPPLY CURRENT 240A Q2, Q3, Q4, Q5 CA3096 TRANSISTOR ARRAY BANDWIDTH = 150kHz 10789fe 16 LT1078/LT1079 U TYPICAL APPLICATIONS Lead-Acid Low-Battery Detector with System Shutdown BATTERY OUTPUT 2M 1% 910k 5% 3 2M 1% 12V + 1 1/2 LT1078 2 LO = BATTERY LOW (IF VS < 10.90V) - 5 8 + 1/2 LT1078 255k 1% 6 280k 1% - LO = SYSTEM SHUTDOWN (IF VS < 10.05V) 7 4 LT1004-1.2 LT1078/79 * TA13 TOTAL SUPPLY CURRENT = 105A Platinum RTD Signal Conditioner with Curvature Correction 3V (LITHIUM) 13k* 8 LT1004-1.2 1 + - 12.3k* 3 10k* 1/2 LT1078 4 1F 2 50k 5C TRIM 43.2k** 1k** 5k 220C TRIM 1k** 6 - 5 + 1/2 LT1078 RP = ROSEMOUNT 118MF ** = TRW MAR-6 0.1% * = 1% METAL FILM 1k** RP 1k AT 0C 1F 7 0.02V TO 2.2VOUT = 2C TO 220C 0.1C 1.21M* (SELECT AT 110C) LT1078/79 * TA14 10789fe 17 LT1078/LT1079 W W SI PLIFIED SCHEMATIC 1/2 LT1078, 1/4 LT1079 V+ 10k 10k 2.2k 5.6k 11.5k 5k 3.6k 1.3k Q54 1 Q16 Q6 Q5 Q14 Q15 2 1 Q32 Q52 Q47 Q30 Q24 Q4 Q46 Q37 Q29 Q3 1 V- 3 8.6k 4 Q11 C1 50pF Q40 3k Q25 Q12 Q35 Q26 C4 4pF 1 2.9k 30 Q44 C5 2.5pF Q27 IN + 600 Q41 V+ OUT IN - 12.5k Q53 Q1 Q21 150k Q18 Q28 Q2 Q22 600 V+ Q31 C3 40pF J1 Q36 Q33 Q48 Q19 Q50 Q42 Q49 Q39 Q9 Q23 Q10 Q17 C2 175pF Q7 Q8 V+ Q43 Q38 5.35k 30 1.35k 6.2k 700k Q51 Q55 10k Q34 6.2k 9.1k Q45 Q20 700k V- LT1078/79 * SIMPLIFIED SCHEM U PACKAGE DESCRIPTIO H Package 8-Lead TO-5 Metal Can (.230 Inch PCD) (Reference LTC DWG # 05-08-1321) 0.335 - 0.370 (8.509 - 9.398) DIA 0.027 - 0.045 (0.686 - 1.143) 45TYP 0.305 - 0.335 (7.747 - 8.509) 0.040 (1.016) MAX 0.028 - 0.034 (0.711 - 0.864) 0.050 (1.270) MAX SEATING PLANE 0.010 - 0.045* (0.254 - 1.143) 0.016 - 0.021** (0.406 - 0.533) 0.230 (5.842) TYP 0.165 - 0.185 (4.191 - 4.699) GAUGE PLANE PIN 1 REFERENCE PLANE 0.500 - 0.750 (12.700 - 19.050) 0.110 - 0.160 (2.794 - 4.064) INSULATING STANDOFF *LEAD DIAMETER IS UNCONTROLLED BETWEEN THE REFERENCE PLANE AND 0.045" BELOW THE REFERENCE PLANE 0.016 - 0.024 **FOR SOLDER DIP LEAD FINISH, LEAD DIAMETER IS (0.406 - 0.610) H8 (TO-5) 0.230 PCD 1197 OBSOLETE PACKAGE 10789fe 18 LT1078/LT1079 U PACKAGE DESCRIPTIO J8 Package 8-Lead CERDIP (Narrow .300 Inch, Hermetic) (Reference LTC DWG # 05-08-1110) 0.300 BSC (0.762 BSC) CORNER LEADS OPTION (4 PLCS) 0.015 - 0.060 (0.381 - 1.524) 0.023 - 0.045 (0.584 - 1.143) HALF LEAD OPTION 0.045 - 0.068 (1.143 - 1.727) FULL LEAD OPTION 0.008 - 0.018 (0.203 - 0.457) 0.405 (10.287) MAX 0.005 (0.127) MIN 0.200 (5.080) MAX 8 6 7 5 0.025 (0.635) RAD TYP 0.220 - 0.310 (5.588 - 7.874) 0 - 15 1 NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE OR TIN PLATE LEADS 0.045 - 0.065 (1.143 - 1.651) 0.014 - 0.026 (0.360 - 0.660) 0.100 (2.54) BSC 2 3 4 0.125 3.175 MIN J8 1298 J Package 14-Lead CERDIP (Narrow .300 Inch, Hermetic) (Reference LTC DWG # 05-08-1110) 0.300 BSC (0.762 BSC) 0.015 - 0.060 (0.381 - 1.524) 0.008 - 0.018 (0.203 - 0.457) 0.005 (0.127) MIN 0.200 (5.080) MAX 0.785 (19.939) MAX 14 12 13 11 10 9 8 0.220 - 0.310 (5.588 - 7.874) 0.025 (0.635) RAD TYP 0 - 15 1 0.045 - 0.065 (1.143 - 1.651) 0.014 - 0.026 (0.360 - 0.660) NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE OR TIN PLATE LEADS 0.100 (2.54) BSC 2 3 4 5 6 7 0.125 (3.175) MIN J14 1298 OBSOLETE PACKAGES N8 Package 8-Lead PDIP (Narrow .300 Inch) (Reference LTC DWG # 05-08-1510) 0.300 - 0.325 (7.620 - 8.255) 0.009 - 0.015 (0.229 - 0.381) ( +0.035 0.325 -0.015 +0.889 8.255 -0.381 ) 0.045 - 0.065 (1.143 - 1.651) 0.400* (10.160) MAX 0.130 0.005 (3.302 0.127) 0.065 (1.651) TYP 8 7 6 5 1 2 3 4 0.255 0.015* (6.477 0.381) 0.100 (2.54) BSC 0.125 (3.175) 0.020 MIN (0.508) MIN 0.018 0.003 (0.457 0.076) N8 1098 *THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm) 10789fe Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 19 LT1078/LT1079 U PACKAGE DESCRIPTION N Package 14-Lead PDIP (Narrow .300 Inch) (Reference LTC DWG # 05-08-1510) 0.130 0.005 (3.302 0.127) 0.300 - 0.325 (7.620 - 8.255) 0.045 - 0.065 (1.143 - 1.651) 0.020 (0.508) MIN 0.005 (0.125) MIN 0.100 (2.54) *THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. BSC MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm) ( 8.255 +0.889 -0.381 ) 0.125 (3.175) MIN 14 13 12 11 10 9 8 1 2 3 4 5 6 7 0.255 0.015* (6.477 0.381) 0.065 (1.651) TYP 0.009 - 0.015 (0.229 - 0.381) +0.035 0.325 -0.015 0.770* (19.558) MAX 0.018 0.003 (0.457 0.076) N14 1098 S8 Package 8-Lead Plastic Small Outline (Narrow .150 Inch) (Reference LTC DWG # 05-08-1610) 0.010 - 0.020 x 45 (0.254 - 0.508) 0.008 - 0.010 (0.203 - 0.254) 0.053 - 0.069 (1.346 - 1.752) 0- 8 TYP 0.016 - 0.050 (0.406 - 1.270) 0.014 - 0.019 (0.355 - 0.483) TYP *DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE **DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE 0.189 - 0.197* (4.801 - 5.004) 7 8 5 6 0.004 - 0.010 (0.101 - 0.254) 0.150 - 0.157** (3.810 - 3.988) 0.228 - 0.244 (5.791 - 6.197) 0.050 (1.270) BSC 1 3 2 4 SO8 1298 SW Package 16-Lead Plastic Small Outline (Wide .300 Inch) (Reference LTC DWG # 05-08-1620) 0.291 - 0.299** (7.391 - 7.595) 0.093 - 0.104 (2.362 - 2.642) 0.010 - 0.029 x 45 (0.254 - 0.737) 0.398 - 0.413* (10.109 - 10.490) 0.037 - 0.045 (0.940 - 1.143) 16 15 14 13 12 11 10 9 0 - 8 TYP 0.009 - 0.013 (0.229 - 0.330) 0.050 (1.270) BSC NOTE 1 0.004 - 0.012 (0.102 - 0.305) 0.394 - 0.419 (10.007 - 10.643) NOTE 1 0.014 - 0.019 (0.356 - 0.482) TYP 0.016 - 0.050 (0.406 - 1.270) NOTE: 1. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS. THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS *DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE **DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE 1 2 3 4 5 6 7 8 S16 (WIDE) 1098 10789fe 20 Linear Technology Corporation LT/CPI 1201 1.5K REV E * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com LINEAR TECHNOLOGY CORPORATION 1994