MIC860 TeenyTM Ultra-Low Power Op Amp General Description Features The SC70 packaging achieves significant board space savings over devices packaged in SOT-23 or MSOP-8 packaging. * * * * * * * The SC70 occupies approximately half the board area of an SOT-23 package. Applications The MIC860 is a rail-to-rail output, operational amplifier in TeenyTM SC70 packaging. The MIC860 provides 4MHz gain-bandwidth product while consuming an incredibly low 30A supply current. Datasheets and support documentation are available on Micrel's web site at: www.micrel.com. * * * * * TeenyTM SC70 packaging 4MHz gain-bandwidth product 30A supply current Rail-to-rail output Ground sensing at input common mode to GND Common mode to GND Drives large capacitive loads Portable equipment PDAs Pagers Cordless phones Consumer electronics Functional Pinout Teeny is a trademark of Micrel, Inc. Micrel Inc. * 2180 Fortune Drive * San Jose, CA 95131 * USA * tel +1 (408) 944-0800 * fax + 1 (408) 474-1000 * http://www.micrel.com September 9, 2014 Revision 2.0 Micrel, Inc. MIC860 Ordering Information Part Number Marking(1) Junction Temp. Range Package MIC860YC5 A32 -40C to +85C 5-Pin SC-70 Note: 1. Underbar marking may not be to scale. Pin Configuration 5-pin SC-70 (C5) (Top View) Pin Description Pin Number Pin Name 1 IN+ Non-inverting input. 2 V- Negative power supply connection. Connect a 10F and 0.1F capacitor in parallel to this pin for power supply bypassing. 3 IN- Inverting input. 4 OUT 5 V+ September 9, 2014 Pin Function Output of operational amplifier. Positive power supply input. Connect a 10F and 0.1F capacitor in parallel to this pin for power supply bypassing. 2 Revision 2.0 Micrel, Inc. MIC860 Absolute Maximum Ratings(2) Operating Ratings(3) Supply Voltage (VV+ - VV-) ........................................ +6.0V Differential Input Voltage (|VIN+ - VIN-|)(5) ................... +6.0V Input Voltage (VIN+ - VIN-) ................... V+ + 0.3V, V- -0.3V Lead Temperature (soldering, 5 sec.) ........................ 260C Output Short-Circuit Current Duration ....................Indefinite Storage Temperature (TS) ......................................... 150C ESD Rating(4) ................................................. ESD Sensitive Supply Voltage (VV+ - VV-) ....................... +2.43V to +5.25V Ambient Temperature (TA) .......................... -40C to +85C Packaging Thermal Resistance 5-pin SC-70 (JA) ............................................. 450C/W Electrical Characteristics V+ = +2.7V, V- = 0V, VCM = V+/2; RL= 500k to V+/2; TA= 25C, unless otherwise noted. Bold values indicate -40C TA +85C. Symbol VOS Parameter Condition Input Offset Voltage Min. Typ. Max. Units -20 -5 15 mV 20 mV -25 Input Offset Voltage Temp Coefficient 20 V/C IB Input Bias Current 20 pA IOS Input Offset Current 10 pA VCM Input Voltage Range CMRR > 60dB 1 1.8 V CMRR Common-Mode Rejection Ratio 0 < VCM < 1.35V 38 76 dB PSRR Power Supply Rejection Ratio Supply voltage change of 3V 40 78 dB RL = 5k, VOUT= 2VPP 50 66 dB RL = 100k, VOUT= 2VPP 66 81 dB RL = 500k, VOUT= 2VPP AVOL VOUT Large-Signal Voltage Gain Maximum Output Voltage Swing 76 91 dB RL = 5k V70mV V34mV V RL = 500k V2mV V0.7mV RL = 5k RL = 500k V V11mV V50mV mV V0.2mV V2mV mV VOUT Minimum Output Voltage Swing GBW Gain-Bandwidth Product 4 MHz SR Slew Rate 3 V/s ISC Short-Circuit Output Current IS Supply Current Source 4.5 6 mA Sink 10 16 mA No Load 30 50 A Notes: 2. Exceeding the absolute maximum ratings may damage the device. 3. The device is not guaranteed to function outside its operating ratings. 4. Devices are ESD sensitive. Handling precautions are recommended. Human body model, 1.5k in series with 100pF. Pin 4 is ESD sensitive. 5. Exceeding the maximum differential input voltage will damage the input stage and degrade performance (in particular, input bias current is likely to increase. September 9, 2014 3 Revision 2.0 Micrel, Inc. MIC860 Electrical Characteristics(5) (Continued) V+= +5V, V-= 0V, VCM= V+/2; RL= 500k to V+/2; TA= 25C, unless otherwise noted. Bold values indicate -40C TA +85C. Symbol VOS Parameter Condition Input Offset Voltage Min. Typ. Max. Units -20 -5 20 mV Input Offset Voltage Temp Coefficient 20 V/C IB Input Bias Current 20 pA IOS Input Offset Current 10 pA VCM Input Voltage Range CMRR > 60dB 3.5 4.2 V CMRR Common-Mode Rejection Ratio 0 < VCM < 3.5V 44 77 dB PSRR Power Supply Rejection Ratio Supply voltage change of 1V 40 79 dB RL = 5k, VOUT 4.8VPP 52 66 dB RL = 100k, VOUT 4.8VPP 67 80 dB RL = 500k, VOUT 4.8VPP 75 90 dB RL = 5k V75mV V37mV V RL = 500k V35mV V4mV V AVOL VOUT VOUT Large-Signal Voltage Gain Maximum Output Voltage Swing Minimum Output Voltage Swing RL = 5k V14mV V40mV RL = 500k V0.4mV V5mV mV mV GBW Gain-Bandwidth Product 4 MHz SR Slew Rate 3 V/s ISC Short-Circuit Output Current IS Supply Current September 9, 2014 Source 15 23 mA Sink 30 47 mA No Load 33 4 55 A Revision 2.0 Micrel, Inc. MIC860 Test Circuits Test Circuit 1. AV = 10 Test Circuit 2. AV = 2 Test Circuit 3. AV = 1 Test Circuit 4. AV = -1 Test Circuit 5. Positive Power Supply Rejection Ratio Measurement September 9, 2014 5 Revision 2.0 Micrel, Inc. MIC860 Typical Characteristics September 9, 2014 6 Revision 2.0 Micrel, Inc. MIC860 Typical Characteristics (Continued) September 9, 2014 7 Revision 2.0 Micrel, Inc. MIC860 Typical Characteristics (Continued) September 9, 2014 8 Revision 2.0 Micrel, Inc. MIC860 Functional Characteristics (Continued) September 9, 2014 9 Revision 2.0 Micrel, Inc. MIC860 Functional Characteristics (Continued) September 9, 2014 10 Revision 2.0 Micrel, Inc. MIC860 Functional Characteristics (Continued) September 9, 2014 11 Revision 2.0 Micrel, Inc. MIC860 Application Information Power Supply Bypassing Regular supply bypassing techniques are recommended. A 10F capacitor in parallel with a 0.1F capacitor on both the positive and negative supplies are ideal. For best perfor- mance all bypassing capacitors should be located as close to the op amp as possible and all capacitors should be low ESL (equivalent series inductance), ESR (equivalent series resistance). Surface-mount ceramic capacitors are ideal. Supply and Loading Considerations The MIC860 is intended for single supply applications configured with a grounded load. It is not advisable to operate the MIC860 with either: 1). A grounded load and split supplies (V) or 2). A single supply where the load is terminated above ground. Under the above conditions, if the load is less than 20k and the output swing is greater than 1V(peak), there may be some instability when the output is sinking current. September 9, 2014 12 Revision 2.0 Micrel, Inc. MIC860 Package Information and Recommended Land Pattern(6) 5-pin SC70 (C5) Note: 6. Package information is correct as of the publication date. For updates and most current information, go to www.micrel.com. MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com Micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this data sheet. This information is not intended as a warranty and Micrel does not assume responsibility for its use. Micrel reserves the right to change circuitry, specifications and descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Micrel's terms and conditions of sale for such products, Micrel assumes no liability whatsoever, and Micrel disclaims any express or implied warranty relating to the sale and/or use of Micrel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. (c) 2006 Micrel, Incorporated. September 9, 2014 13 Revision 2.0