TC74LCX244F/FT/FK TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC74LCX244F,TC74LCX244FT,TC74LCX244FK Low-Voltage Octal Bus Buffer with 5-V Tolerant Inputs and Outputs The TC74LCX244 is a high-performance CMOS octal bus buffer. Designed for use in 3.3-V systems, it achieves high-speed operation while maintaining the CMOS low power dissipation. The device is designed for low-voltage (3.3 V) VCC applications, but it could be used to interface to 5 V supply environment for both inputs and outputs. The 74LCX244F/FT is a non-inverting 3-state buffer having two active-low output enables. This device is designed to be used with 3-state memory address drivers, etc. All inputs are equipped with protection circuits against static discharge. TC74LCX244F TC74LCX244FT Features * Low-voltage operation: VCC = 1.65 to 3.6 V * High-speed operation: tpd = 6.5 ns (max) (VCC = 3.0 to 3.6 V) * Ouput current: |IOH|/IOL = 24 mA (min) (VCC = 3.0 V) * Latch-up performance: 500 mA * Available in JEITA SOP, TSSOP and VSSOP (US) * Power-down protection provided on all inputs and outputs * Pin and function compatible with the 74 series TC74LCX244FK (74AC/VHC/HC/F/ALS/LS etc.) 244 type Weight SOP20-P-300-1.27A TSSOP20-P-0044-0.65A VSSOP20-P-0030-0.50 : 0.22 g (typ.) : 0.08 g (typ.) : 0.03 g (typ.) Note: The Electrical Characteristics of VCC=1.80.15V is only applicable for products which manufactured from January 2009 onward. 1 2010-01-31 TC74LCX244F/FT/FK Pin Assignment (top view) IEC Logic Symbol 1 20 VCC 1A1 2 19 2OE 2Y4 3 18 1Y1 1A2 4 17 2A4 2Y3 5 16 1Y2 1OE 1OE 1A1 1A2 1A3 1A4 2OE 1A3 6 15 2A3 2Y2 7 14 1Y3 1A4 8 13 2A2 2Y1 9 12 1Y4 GND 10 11 2A1 2A1 2A2 2A3 2A4 1 EN 2 4 6 8 19 11 13 15 17 18 16 14 12 1Y1 1Y2 1Y3 1Y4 EN 9 7 5 3 2Y1 2Y2 2Y3 2Y4 Truth Table Inputs OE An Outputs L L L L H H H X Z X: Don't care Z: High impedance 2 2010-01-31 TC74LCX244F/FT/FK Absolute Maximum Ratings (Note 1) Symbol Rating Unit Power supply voltage Characteristics VCC -0.5 to 7.0 V DC input voltage VIN -0.5 to 7.0 V -0.5 to 7.0 (Note 2) DC output voltage VOUT -0.5 to VCC + 0.5 V (Note 3) IIK -50 Output diode current IOK 50 DC output current IOUT 50 mA Input diode current Power dissipation DC VCC/ground current Storage temperature mA (Note 4) mA PD 180 mW ICC/IGND 100 mA Tstg -65 to 150 C Note 1: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or even destruction. Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook ("Handling Precautions"/"Derating Concept and Methods") and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 2: Output in OFF state Note 3: High or low state. IOUT absolute maximum rating must be observed. Note 4: VOUT < GND, VOUT > VCC Operating Ranges (Note 1) Characteristics Symbol Power supply voltage VCC Input voltage VIN Output voltage VOUT Output current IOH/IOL Rating Unit 1.65 to 3.6 1.5 to 3.6 (Note 2) 0 to 5.5 V 0 to 5.5 (Note 3) 0 to VCC (Note 4) 24 (Note 5) 12 (Note 6) Operating temperature Topr -40 to 85 Input rise and fall time dt/dv 0 to 10 V V mA C (Note 7) ns/V Note 1: The operating ranges must be maintained to ensure the normal operation of the device. Unused inputs must be tied to either VCC or GND. Note 2: Data retention only Note 3: Output in OFF state Note 4: High or low state Note 5: VCC = 3.0 to 3.6 V Note 6: VCC = 2.7 to 3.0 V Note 7: VIN = 0.8 to 2.0 V, VCC = 3.0 V 3 2010-01-31 TC74LCX244F/FT/FK Electrical Characteristics DC Characteristics (Ta = -40 to 85C) Characteristics H-level Symbol Test Condition Min Max 1.65 to 2.3 VCCx0.9 2.3 to 2.7 1.7 2.7 to 3.6 2.0 1.65 to 2.3 VCCx0.1 2.3 to 2.7 0.7 2.7 to 3.6 0.8 1.65 to 3.6 VCC-0.2 IOH = -4 mA 1.65 1.05 IOH = -8 mA 2.3 1.7 IOH = -12 mA 2.7 2.2 IOH = -18 mA 3.0 2.4 IOH = -24 mA 3.0 2.2 IOL = 100 A 1.65 to 3.6 0.2 IOL = 4 mA 1.65 0.45 IOL = 8 mA 2.3 0.7 IOL = 12 mA 2.7 0.4 IOL = 16 mA 3.0 0.4 IOL = 24 mA 3.0 0.55 1.65 to 3.6 5.0 A 1.65 to 3.6 5.0 A VIN/VOUT = 5.5 V 0 10.0 A VIN = VCC or GND 1.65 to 3.6 10.0 VIN/VOUT = 3.6 to 5.5 V 1.65 to 3.6 10.0 VIH = VCC - 0.6V 2.7 to 3.6 500 VIH Input voltage L-level VIL IOH = -100 A H-level VOH VIN = VIH or VIL Output voltage L-level VOL Input leakage current IIN 3-state output off-state current IOZ Power off leakage current IOFF Quiescent supply current ICC Increase in ICC per input ICC VIN = VIH or VIL VIN = 0 to 5.5 V VIN = VIH or VIL VOUT = 0 to 5.5 V 4 VCC (V) Unit V V A 2010-01-31 TC74LCX244F/FT/FK AC Characteristics (Ta = -40 to 85C) Characteristics Propagation delay time Output enable time Output disable time Output to output skew Note: Symbol tpLH tpHL tpZL tpZH tpLZ tpHZ Test Condition Figure 1, Figure 2 Figure 1, Figure 3 Figure 1, Figure 3 tosLH (Note) tosHL Min Max 1.8 0.15 25.0 2.5 0.2 8.5 2.7 7.5 3.3 0.3 1.5 6.5 1.8 0.15 32.0 2.5 0.2 16.0 2.7 9.0 3.3 0.3 1.5 8.0 1.8 0.15 30.0 2.5 0.2 15.0 2.7 8.0 3.3 0.3 1.5 7.0 2.7 3.3 0.3 1.0 VCC (V) Unit ns ns ns ns Parameter guaranteed by design. (tosLH = |tpLHm - tpLHn|, tosHL = |tpHLm - tpHLn|) Dynamic Switching Characteristics (Ta = 25C, input: tr = tf = 2.5 ns, CL = 50 pF, RL = 500 ) Characteristics Symbol Test Condition VCC (V) Typ. Unit Quiet output maximum dynamic VOL VOLP VIH = 3.3 V, VIL = 0 V 3.3 0.8 V Quiet output minimum dynamic VOL |VOLV| VIH = 3.3 V, VIL = 0 V 3.3 0.8 V Typ. Unit Capacitive Characteristics (Ta = 25C) Characteristics Input capacitance Output capacitance Power dissipation capacitance Note: Symbol Test Condition CIN 3.3 7 pF COUT 3.3 8 pF 3.3 25 pF CPD fIN = 10 MHz VCC (V) (Note) CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption. Average operating current can be obtained by the equation: ICC (opr) = CPD * VCC * fIN + ICC/8 (per bit) 5 2010-01-31 TC74LCX244F/FT/FK AC Test Circuit RL Switch Parameter Switch tpLH, tpHL Open 6.0 V Measure tpLZ, tpZL RL CL Output Open 6.0 V or VCCx2 GND @ VCC =3.30.3V @ VCC =2.7V VCCx2 @ VCC =2.50.2V @ VCC =1.80.15V tpHZ, tpZH GND Figure 1 6 2010-01-31 TC74LCX244F/FT/FK AC Waveform tr tf VIH 90% VIM Input (A) 10% GND VOH Output (Y) VOM tpLH VOL tpHL Figure 2 tpLH, tpHL tr tf 90% VIM Output Enable ( OE ) VIH 10% tpLZ GND tpZL VOH Output (Y) Low to Off to Low VOM tpHZ VX VOL tpZH VOH VY Output (Y) High to Off to High VOM GND Outputs enabled Outputs enabled Outputs disabled Figure 3 tpLZ, tpHZ, tpZL, tpZH VCC Symbol 3.3 0.3 V 2.7V Input Output Load 2.5 0.2 V 1.8 0.15 V VIH 2.7V VCC VCC VIM 1.5V VCC/2 VCC/2 tr,tf 2.5ns 2.0ns 2.0ns VOM 1.5V VOH/2 VOH/2 VX VOL +0.3V VOL +0.15V VOL +0.15V VY VOH -0.3V VOH -0.15V VOH -0.15V CL 50pF 30pF 30pF RL 500 500 1k 7 2010-01-31 TC74LCX244F/FT/FK Package Dimensions Weight: 0.22 g (typ.) 8 2010-01-31 TC74LCX244F/FT/FK Package Dimensions Weight: 0.08 g (typ.) 9 2010-01-31 TC74LCX244F/FT/FK Package Dimensions Weight: 0.03 g (typ.) 10 2010-01-31 TC74LCX244F/FT/FK RESTRICTIONS ON PRODUCT USE * Toshiba Corporation, and its subsidiaries and affiliates (collectively "TOSHIBA"), reserve the right to make changes to the information in this document, and related hardware, software and systems (collectively "Product") without notice. * This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with TOSHIBA's written permission, reproduction is permissible only if reproduction is without alteration/omission. * Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily injury or damage to property, including data loss or corruption. Before customers use the Product, create designs including the Product, or incorporate the Product into their own applications, customers must also refer to and comply with (a) the latest versions of all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes for Product and the precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the instructions for the application with which the Product will be used with or for. Customers are solely responsible for all aspects of their own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS. * Product is intended for use in general electronics applications (e.g., computers, personal equipment, office equipment, measuring equipment, industrial robots and home electronics appliances) or for specific applications as expressly stated in this document. Product is neither intended nor warranted for use in equipment or systems that require extraordinarily high levels of quality and/or reliability and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage or serious public impact ("Unintended Use"). Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. Do not use Product for Unintended Use unless specifically permitted in this document. * Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part. * Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. * The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. * ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT. * Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology products (mass destruction weapons). Product and related software and technology may be controlled under the Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations. * Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. TOSHIBA assumes no liability for damages or losses occurring as a result of noncompliance with applicable laws and regulations. 11 2010-01-31