LTC4401-1/LTC4401-2 RF Power Controllers with 250kHz Loop BW and 45dB Dynamic Range U FEATURES DESCRIPTIO TM RF Power Amplifier Control in ThinSOT Package Internal Schottky Diode Detector with > 45dB Range Wide Input Frequency Range: 300MHz to 2.7GHz (LTC4401-1) 300MHz to 2GHz (LTC4401-2) Autozero Loop Cancels Offset Errors and Temperature Dependent Offsets Wide VCC Range: 2.7V to 6V Automatic Bandwidth Control Improves Low Power Ramp Response Allows Direct Connection to Battery RF Output Power Set by External DAC Internal Frequency Compensation Rail-to-Rail Power Control Output Power Control Signal Overvoltage Protection Low Operating Current: 1mA Low Shutdown Current: 10A Two Pole PCTL Input Filtering Low Profile (1mm) SOT-23 (ThinSOTTM) (LTC4401-1) and 8-Pin MSOP (LTC4401-2) Packages U APPLICATIO S RF power is controlled by driving the RF amplifier power control pins and sensing the resultant RF output power via a directional coupler. The RF sense voltage is peak detected using an on-chip Schottky diode. This detected voltage is compared to the DAC voltage at the PCTL pin to control the output power. The RF power amplifier is protected against high power control pin voltages. Internal and external offsets are cancelled over temperature by an autozero control loop, allowing accurate low power programming. The shutdown feature disables the part and reduces the supply current to < 10A. A dual control channel version (LTC4401-2) is also available in an 8-pin MSOP package. , LTC and LT are registered trademarks of Linear Technology Corporation. ThinSOT is a trademark of Linear Technology Corporation. GSM/GPRS Cellular Telephones PCS Devices Wireless Data Modems U.S. TDMA Cellular Phones U The LTC(R)4401-1 is a SOT-23 RF power controller for slow turn-on RF power amplifiers operating in the 300MHz to 2.7GHz range. The loop bandwidth is set at 250kHz to improve frequency stability when controlling slow turn-on RF power amplifiers such as the Conexant CX77301/CX77302, CX77304, CX77314, Anadigics AWT6107 and the RF Micro Devices RF3160. TYPICAL APPLICATIO LTC4401-1 Dual Band Cellular Telephone Transmitter 68 33pF Li-Ion 6 0.1F RF VCC BAND SELECT 1 LTC4401-1 SHDN 4 3 DAC SHDN VPCA PCTL GND 5 2 VPC 900MHz INPUT 1.8GHz INPUT 900MHz OUTPUT PA MODULE 1.8GHz OUTPUT 50 4401 TA01 4401fa 1 LTC4401-1/LTC4401-2 W W W AXI U U ABSOLUTE RATI GS (Note 1) VCC to GND .............................................. - 0.3V to 6.5V VPCA/B Voltage to GND ............................ - 0.3V to 3.2V PCTL Voltage to GND ................. - 0.3V to (VCC + 0.3V) RF Voltage to GND ............................ (VCC - 2.6V) to 7V BSEL, SHDN Voltage to GND ...... - 0.3V to (VCC + 0.3V) IVPCA/B .................................................................. 10mA Operating Temperature Range (Note 2) .. - 30C to 85C Storage Temperature Range ................ - 65C to 150C Maximum Junction Temperature ......................... 125C Lead Temperature (Soldering, 10 sec)................. 300C U U W PACKAGE/ORDER I FOR ATIO ORDER PART NUMBER TOP VIEW RF 1 6 VCC GND 2 5 VPCA PCTL 3 4 SHDN LTC4401-1ES6 S6 PACKAGE 6-LEAD PLASTIC TSOT-23 ORDER PART NUMBER TOP VIEW VCC VPCA VPCB GND 1 2 3 4 8 7 6 5 RF BSEL SHDN PCTL LTC4401-2EMS8 S6 PART MARKING MS8 PACKAGE 8-LEAD PLASTIC MSOP MS8 PART MARKING LTXA TJMAX = 125C, JA = 250C/W LTXC TJMAX = 125C, JA = 230C/W Consult LTC Marketing for parts specified with wider operating temperature ranges. ELECTRICAL CHARACTERISTICS The denotes specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VCC = 3.6V, SHDN = HI, unless otherwise noted. PARAMETER CONDITIONS MIN VCC Operating Voltage TYP MAX 6 V 10 20 A 2.7 UNITS IVCC Shutdown Current SHDN = 0V IVCC Operating Current SHDN = HI, IVPCA/B = 0mA VPCA/B VOL RLOAD = 400, Enabled VPCA/B Dropout Voltage ILOAD = 6mA, VCC = 3V VPCA/B Voltage Clamp PCTL = 1V 2.7 2.9 VPCA/B Output Current VPCA/B = 2.4V, VCC = 3V 7 10 VPCA/B Enable Time SHDN = VCC (Note 5) 9 10.2 s VPCA/B Bandwidth CLOAD = 100pF, RLOAD = 2k (Note 8) 175 250 130 330 kHz kHz VPCA/B Load Capacitance (Note 6) 100 pF VPCA/B Slew Rate VPCTL = 2V Step, CLOAD = 100pF, RLOAD = 400 (Note 3) 1.2 0 PCTL < 80mV PCTL > 160mV 1 VPCA/B Droop mA V VCC - 0.25 V 3.1 V mA 2 Open Loop (Note 9) 300 BSEL, SHDN Input Threshold VCC = 2.7V to 6V 0.35 BSEL, SHDN Input Current BSEL = SHDN = 3.6V 16 PCTL Input Voltage Range (Note 7) 0 60 PCTL Input Resistance PCTL Input Filter 450 24 90 550 mV 1.4 V 36 A 2.4 V 120 270 (Note 4) V/s V/ms 1 VPCA/B Start Voltage Autozero Range 1.5 1.9 0.05 k kHz 400 mV 4401fa 2 LTC4401-1/LTC4401-2 ELECTRICAL CHARACTERISTICS The denotes specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VCC = 3.6V, SHDN = HI, unless otherwise noted. PARAMETER CONDITIONS MIN MAX UNITS RF Input Frequency Range LTC4401-1 (Note 6) LTC4401-2 (Note 6) 300 300 2700 2000 MHz MHz RF Input Power Range (LTC4401-1) RF Frequency = 900MHz (Note 6) RF Frequency = 1800MHz (Note 6) RF Frequency = 2400MHz (Note 6) RF Frequency = 2700MHz (Note 6) -28 -26 -24 -22 18 18 16 16 dBm dBm dBm dBm RF Input Power Range (LTC4401-2) RF Frequency = 900MHz (Note 6) RF Frequency = 2000MHz (Note 6) -28 -26 18 18 dBm dBm RF Input Resistance Referenced to VCC 350 150 Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Note 2: The LTC4401-X is guaranteed to meet performance specifications from 0C to 70C. Specifications over the - 30C to 85C operating temperature range are assured by design, characterization and correlation with statistical process controls. Note 3: Slew rate is measured open loop. The slew time at VPCA/B is measured between 1V and 2V. Note 4: Maximum DAC zero-scale offset voltage that can be applied to PCTL. TYP 250 Note 5: This is the time from SHDN rising edge 50% switch point to VPCA = 0.25V. Note 6: Guaranteed by design. This parameter is not production tested. Note 7: Includes maximum DAC offset voltage and maximum control voltage. Note 8: Bandwidth is calculated using the 10% to 90% rise time: BW = 0.35/rise time Note 9: Measured 12s after SHDN = HI. U W 10000 75C 25C -30C 1000 100 10 1 -28 -22 -16 -10 -4 2 8 RF INPUT POWER (dBm) 14 4401 G01 LTC4401-1 Detector Characteristics at 1800MHz 10000 75C 25C -30C 1000 100 10 1 -26 -20 -14 -8 -2 4 10 RF INPUT POWER (dBm) 16 4401 G02 PCTL REFERENCED DETECTOR OUTPUT VOLTAGE (mV) LTC4401-1 Detector Characteristics at 900MHz PCTL REFERENCED DETECTOR OUTPUT VOLTAGE (mV) PCTL REFERENCED DETECTOR OUTPUT VOLTAGE (mV) TYPICAL PERFOR A CE CHARACTERISTICS LTC4401-1 Detector Characteristics at 2400MHz 10000 75C 25C -30C 1000 100 10 1 -24 -20 -16 -12 -8 -4 0 4 8 RF INPUT POWER (dBm) 12 16 4401 G03 4401fa 3 LTC4401-1/LTC4401-2 U W 10000 75C 25C -30C 1000 100 10 1 -22 -18 -14 -10 -6 -2 2 6 RF INPUT POWER (dBm) 10 14 LTC4401-2 Detector Characteristics at 900MHz 10000 75C 25C -30C 1000 100 10 1 -28 -22 -16 -10 -4 2 8 RF INPUT POWER (dBm) 4401 G04 U U U PI FU CTIO S 14 4401 G05 PCTL REFERENCED DETECTOR OUTPUT VOLTAGE (mV) LTC4401-1 Detector Characteristics at 2700MHz PCTL REFERENCED DETECTOR OUTPUT VOLTAGE (mV) PCTL REFERENCED DETECTOR OUTPUT VOLTAGE (mV) TYPICAL PERFOR A CE CHARACTERISTICS LTC4401-2 Detector Characteristics at 1800MHz 10000 75C 25C -30C 1000 100 10 1 -26 -20 -14 -8 -2 4 10 RF INPUT POWER (dBm) 16 4401 G06 (LTC4401-1/LTC4401-2) RF (Pins 1/8): RF Feedback Voltage from the Directional Coupler. Referenced to VCC. A coupling capacitor of 33pF must be used to connect to the ground referenced directional coupler. The frequency range is 300MHz to 2700MHz for the LTC4401-1 and 300MHz to 2000MHz for the LTC4401-2. This pin has an internal 250 termination, an internal Schottky diode detector and peak detector capacitor. SHDN (Pins 4/6): Shutdown Input. A logic low on the SHDN pin places the part in shutdown mode. A logic high places the part in enable mode. SHDN has an internal 150k pulldown resistor to ensure that the part is in shutdown when the drivers are in a three-state condition. GND (Pins 2/4): System Ground. VCC (Pins 6/1): Input Supply Voltage, 2.7V to 6V. VCC should be bypassed with 0.1F and 100pF ceramic capacitors. Used as return for RF 250 termination. PCTL (Pins 3/5): Analog Input. The external power control DAC drives this input. The amplifier servos the RF power until the RF detected signal equals the DAC signal. The input impedance is typically 90k. VPCB (Pin 3): (LTC4401-2 Only) Power Control Voltage Output. This pin drives an external RF power amplifier power control pin. The maximum load capacitance is 100pF. VPCA (Pins 5/2): Power Control Voltage Output. This pin drives an external RF power amplifier power control pin. The maximum load capacitance is 100pF. BSEL (Pin 7): (LTC4401-2 Only) Selects VPCA when Low and VPCB when High. This input has an internal 150k resistor to ground. 4401fa 4 LTC4401-1/LTC4401-2 W BLOCK DIAGRA (LTC4401-1) 68 RF IN 33pF RF PA 50 Li-Ion VCC 6 TXENB AUTOZERO - AZ + + - GAIN COMPRESSION GM + 250 RF 1 + - 30k 28pF 30k 60A GND CLAMP 80mV + 270kHz FILTER + CC 5 BUFFER 38k - RF DET VPCA 30k - 60A 22k VREF 51k 30k + 2 - 33.4k 6k 12 TXENB VBG VREF 10s DELAY CONTROL 100 150k LTC4401-1 4 3 SHDN PCTL 4401-1 BD 4401fa 5 LTC4401-1/LTC4401-2 W BLOCK DIAGRA (LTC4401-2) DIPLEXER 68 900MHZ RF PA 1.8GHz/1.9GHz RF PA 50 33pF Li-Ion VCC 1 TXENB AUTOZERO - AZ + + - GAIN COMPRESSION BUF A GM + 250 RF 8 + - 30k 28pF 30k 60A GND 80mV + MUX1 MUX2 CC 38k - RF DET 30k - 60A 22k VREF 51k 30k + 4 12 33.4k VPCB 100 6k TXENB VREF 3 BUF B - VBG VPCA CLAMP 270kHz FILTER + 2 12 10s DELAY VPCA CONTROL 100 150k 150k LTC4401-2 6 5 7 SHDN PCTL BSEL 4401-2 BD 4401fa 6 LTC4401-1/LTC4401-2 U W U U APPLICATIONS INFORMATION Operation The LTC4401-X RF power control amplifier integrates several functions to provide RF power control over frequencies ranging from 300MHz to 2.7GHz. This product is well suited to control RF power amplifiers that exhibit slow turn-on times. The device also prevents damage to the RF power amplifier due to overvoltage conditions. These functions include an internally compensated power control amplifier to control the RF output power, an autozero section to cancel internal and external voltage offsets, an RF Schottky diode peak detector and amplifier to convert the RF feedback signal to DC, a VPCA/B overvoltage clamp, compression and a bandgap reference. Band Selection The LTC4401-2 is designed to drive two separate power control lines. The BSEL pin will select VPCA when low and VPCB when high. BSEL must be established prior to SHDN being asserted high. Control Amplifier The control amplifier supplies the power control voltage to the RF power amplifier. A portion (typically - 19dB for low frequencies and -14dB for high frequencies) of the RF output voltage is sampled, via a directional coupler, to close the gain control loop. When a DAC voltage is applied to PCTL, the amplifier quickly servos VPCA/B positive until the detected feedback voltage applied to the RF pin matches the voltage at PCTL. This feedback loop provides accurate RF power control. VPCA/B is capable of driving a 6mA load current and 100pF load capacitor. Control Amplifier Compression The gain compression breakpoints are at PCTL = 80mV and PCTL = 160mV. Above 160mV the gain does not change. The compression changes the feedback attenuation thereby reducing the loop gain. RF Detector The internal RF Schottky diode peak detector and amplifier converts the RF feedback voltage from the directional coupler to a low frequency voltage. This voltage is compared to the DAC voltage at the PCTL pin by the control amplifier to close the RF power control loop. The RF pin input resistance is typically 250 and the frequency range of this pin is 300MHz to 2700MHz for the LTC4401-1 and 300MHz to 2000MHz for the LTC4401-2. The detector demonstrates excellent efficiency over a wide range of input power. The Schottky detector is biased at about 60A and drives an on-chip peak detector capacitor of 28pF. Autozero An autozero system is included to improve power programming accuracy over temperature. This section cancels internal offsets associated with the Schottky diode detector and control amplifier. External offsets associated with the DAC driving the PCTL pin are also cancelled. Offset drift due to temperature is cancelled between each burst. The maximum offset voltage allowed at the DAC output is limited to 400mV. Autozeroing is performed during a 10s period after SHDN is asserted high. An internal timer enables the VPCA/B output after 10s. The autozero capacitors are held and the VPCA/B pin is connected to the control amplifier output. The hold droop voltage of typically < 1V/ms provides for accurate offset cancellation. The part should be shut down between bursts or after multiple consecutive bursts. Filter There is a 270kHz two pole filter included in the PCTL path to remove DAC noise. Protection Features The RF power amplifier control voltage pin is overvoltage protected. The VPCA/B overvoltage clamp regulates VPCA/B to 2.9V when the gain and PCTL input combination attempts to exceed this voltage. Modes of Operation Shutdown: The part is in shutdown mode when SHDN is low. VPCA/B is held at ground and the power supply current is typically 10A. 4401fa 7 LTC4401-1/LTC4401-2 U W U U APPLICATIO S I FOR ATIO Enable: When SHDN is asserted high the part will automatically calibrate out all offsets. This takes <10s and is controlled by an internal delay circuit. After 10s VPCA/B will step up to the starting voltage of 450mV. The user can then apply the ramp signal. The user should wait 12s after SHDN has been asserted high before applying the ramp. The DAC should be settled 2s after asserting SHDN high. LTC4401-X Timing Diagram T7 BSEL T8 (LTC4401-2 ONLY) 2s 10s 28s 543s 28s SHDN VPCA/B VSTART PCTL 4400 TA02 T1 T2 T3 T4 T5 T6 T1: LTC4401-X COMES OUT OF SHUTDOWN 12s PRIOR TO BURST T2: INTERNAL TIMER COMPLETES AUTOZERO CORRECTION, <10s T3: BASEBAND CONTROLLER STARTS RF POWER RAMP UP AT 12s AFTER SHDN IS ASSERTED HIGH T4: BASEBAND CONTROLLER COMPLETES RAMP UP T5: BASEBAND CONTROLLER STARTS RF POWER RAMP DOWN AT END OF BURST T6: LTC4401-X RETURNS TO SHUTDOWN MODE BETWEEN BURSTS T7: BSEL CHANGE PRIOR TO SHDN, 0ns TYPICAL (LTC4401-2 ONLY) T8: BSEL CHANGE AFTER TO SHDN, 0ns TYPICAL (LTC4401-2 ONLY) General Layout Considerations The LTC4401-X should be placed near the directional coupler. The feedback signal line to the RF pin should be a 50 transmission line with optional termination or a short line. External Termination The LTC4401-X has an internal 250 termination resistor at the RF pin. If a directional coupler is used, it is recommended that an external 68 termination resistor be connected between the RF coupling capacitor (33pF), and ground at the side connected to the directional coupler. Termination components should be placed adjacent to the LTC4401-X. Power Ramp Profiles The external voltage gain associated with the RF channel can vary significantly between RF power amplifier types. The LTC4401-X frequency compensation has been optimized to be stable with several different power amplifiers and manufacturers. This frequency compensation generally defines the loop dynamics that impact the power/ time response and possibly (slow loops) the power ramp sidebands. The LTC4401-X operates open loop until an RF voltage appears at the RF pin, at which time the loop closes and the output power follows the DAC profile. The RF power amplifier will require a certain control voltage level (threshold) before an RF output signal is produced. The LTC4401-X VPCA/B output(s) must quickly rise to this threshold voltage in order to meet the power/time profile. To reduce this time, the LTC4401-X starts at 450mV. However, at very low power levels the PCTL input signal is small, and the VPCA/B output may take several microseconds to reach the RF power amplifier threshold voltage. To reduce this time, it may be necessary to apply a positive pulse at the start of the ramp to quickly bring the VPCA/B output to the threshold voltage. This can generally be achieved with DAC programming. The magnitude of the pulse is dependent on the RF amplifier characteristics. Power ramp sidebands and power/time are also a factor when ramping to zero power. When the power is ramped down the loop will eventually open at power levels below the LTC4401-X detector threshold. The LTC4401-X will then go open loop and the output voltage at VPCA/B will stop falling. If this voltage is high enough to produce RF output power, the power/time or power ramp sidebands may not meet specification. This problem can be avoided by starting the DAC ramp from 200mV (Figure 1). At the end of the cycle, the DAC can be ramped down to 0mV. This applies a negative signal to the LTC4401-X thereby ensuring that the VPCA/B output will ramp to 0V. The 200mV ramp step must be applied < 2s after SHDN is asserted high to allow the autozero to cancel the step. Slow DAC rise times will extend this time by the additional RC time constants which may require that the DAC is enabled and settled prior to SHDN asserted high. 4401fa 8 LTC4401-1/LTC4401-2 U W U U APPLICATIO S I FOR ATIO 1) The additional voltage gain supplied by the RF power amplifier increases the loop gain raising poles normally below the 0dB axis. The extra voltage gain can vary significantly over input/output power ranges, frequency, power supply, temperature and manufacturer. RF power amplifier gain control transfer functions are often not available and must be generated by the user. Loop oscillations are most likely to occur in the midpower range where the external voltage gain associated with the RF power amplifier typically peaks. It is useful to measure the oscillation or ringing frequency to determine whether it corresponds to the expected loop bandwidth and thus is due to high gain bandwidth. 10 0 RFOUT (dBc) -10 -20 -30 -40 -50 -60 -70 -80 -28 -18 -10 0 543 553 561 571 DAC VOLTAGE TIME (s) START PULSE START CODE ZERO CODE 200mV SHDN 12s, ALLOWS TIME FOR DAC AND AUTOZERO TO SETTLE 4401 F01 Figure 1. LTC4401-X Ramp Timing Demo Board The LTC4401-X demo board is available upon request. The demo board has a 900MHz and an 1800MHz RF channel controlled by the LTC4401-X. Timing signals for SHDN are generated on the board using a 13MHz crystal reference. The PCTL power control pin is driven by a 10-bit DAC and the DAC profile can be loaded via a serial port. The serial port data is stored in a flash memory which is capable of storing eight ramp profiles. The board is supplied preloaded with four GSM power profiles and four DCS power profiles covering the entire power range. External timing signals can be used in place of the internal crystal controlled timing. A variety of RF power amplifiers as well as ramp generation software are available. LTC4401-X Control Loop Stability The LTC4401-X provides a stable control loop for several RF power amplifier models from different manufacturers over a wide range of frequencies, output power levels and VSWR conditions. However, there are several factors that can improve or degrade loop frequency stability. 2) Loop voltage losses supplied by the directional coupler will improve phase margin. The larger the directional coupler loss the more stable the loop will become. However, larger losses reduce the RF signal to the LTC4401-X and detector performance may be degraded at low power levels. (See RF Detector Characteristics.) 3) Additional poles within the loop due to filtering or the turn-on response of the RF power amplifier can degrade the phase margin if these pole frequencies are near the effective loop bandwidth frequency. Generally loops using RF power amplifiers with fast turn-on times have more phase margin. Extra filtering below 16MHz should never be placed within the control loop, as this will only degrade phase margin. 4) Control loop instability can also be due to open-loop issues. RF power amplifiers should first be characterized in an open-loop configuration to ensure self oscillation is not present. Self-oscillation is often related to poor power supply decoupling, ground loops, coupling due to poor layout and extreme VSWR conditions. The oscillation frequency is generally in the 100kHz to 10MHz range. Power supply related oscillation suppression requires large value ceramic decoupling capacitors placed close to the RF power amp supply pins. The range of decoupling capacitor values is typically 1nF to 3.3F. 5) Poor layout techniques associated with the directional coupler area may result in high frequency signals bypassing the coupler. This could result in stability problems due to the reduction in the coupler loss. 4401fa 9 LTC4401-1/LTC4401-2 U W U U APPLICATIO S I FOR ATIO Determining External Loop Gain and Bandwidth The external loop voltage gain contributed by the RF channel and directional coupler network should be measured in a closed-loop configuration. A voltage step is applied to PCTL and the change in VPCA/B is measured. The detected voltage is K * PCTL, where K is the internal gain between PCTL and the RF pin, and the external voltage gain contributed by the RF power amplifier and directional coupler network is K * VPCTL/VVPC. Measuring voltage gain in the closed-loop configuration accounts for the nonlinear detector gain that is dependent on RF input voltage and frequency. The LTC4401-X unity gain bandwidth specified in the data sheet assumes that the net voltage gain contributed by the RF power amplifier and directional coupler is unity. The bandwidth is calculated by measuring the rise time between 10% and 90% of the voltage change at VPCA/B for a small step in voltage applied to PCTL. BW1 = 0.35/rise time The LTC4401-X control amplifier unity gain bandwidth (BW1) is typically 250kHz below a PCTL voltage of 80mV. For PCTL voltages < 80mV, the RF detected voltage is 0.6PCTL. For PCTL voltages >160mV, RF detected voltage is 1.22PCTL - 0.1. This change in gain is due to an internal compression circuit designed to extend the detector range. RLOAD = 2k CLOAD = 33pF PCTL = 60mV GAIN 1k 10k 100k FREQUENCY (Hz) 1M 4401 F02 Figure 2. Measured Open-Loop Gain and Phase, PCTL < 80mV VOLTAGE GAIN (dB) PHASE 160 140 120 100 80 60 40 20 0 -20 -40 -60 -80 -100 -120 10M External pole frequencies within the loop will further reduce phase margin. The phase margin degradation, due to external and internal pole combinations, is difficult to determine since complex poles are present. Gain peaking may occur, resulting in higher bandwidth and lower phase margin than predicted from the open-loop Bode plot. A low frequency AC SPICE model of the LTC4401-X power controller is included to better determine pole and zero interactions. The user can apply external gains and poles to determine bandwidth and phase margin. DC, transient and RF information cannot be extracted from the present model. The model is suitable for external gain evaluations up to 6 x. The 270kHz PCTL input filter limits the bandwidth, therefore, use the RF input as demonstrated in the model. Gain compression is not modeled. 80 70 60 50 40 30 20 10 0 -10 -20 -30 -40 -50 -60 100 180 160 140 120 100 80 60 40 20 0 -20 -40 -60 -80 -100 10M RLOAD = 2k CLOAD = 33pF PHASE GAIN 1k 10k 100k FREQUENCY (Hz) 1M PHASE (DEG) 80 70 60 50 40 30 20 10 0 -10 -20 -30 -40 -50 -60 100 PHASE (DEG) VOLTAGE GAIN (dB) For example, to determine the external RF channel loop voltage gain with the loop closed, apply a 100mV step to PCTL from 300mV to 400mV. VPCA/B will increase to supply enough feedback voltage to the RF pin to cancel this 100mV step which would be the required detected voltage step of 122mV. VPCA/B changed from 1.5V to 1.561V to create the RF output power change required. The net external voltage gain contributed by the RF power amplifier and directional coupler network can be calculated by dividing the 122mV change at the RF pin by the 61mV change at the VPCA/B pin. The net external voltage gain would then be approximately 2. The loop bandwidth extends to 2 * BW1. If BW1 is 130kHz, the loop bandwidth increases to approximately 260kHz. The phase margin can be determined from Figures 2 and 3. Repeat the above voltage gain measurement over the full power and frequency range. 4401 F03 Figure 3. Measured Open-Loop Gain and Phase, PCTL > 160mV 4401fa 10 LTC4401-1/LTC4401-2 U W U U APPLICATIO S I FOR ATIO Users should note very carefully the following factors regarding this model: Model performance in general will reflect typical baseline specs for a given device, and certain aspects of performance may not be modeled fully. While reasonable care has been taken in the preparation, we cannot be responsible for correct application on any and all computer systems. Model users are hereby notified that these models are supplied "as is", with no direct or implied responsibility on the part of LTC for their operation within a customer circuit or system. Further, Linear Technology Corporation reserves the right to change these models without prior notice. CONTROL AMPLIFER RF POWER AMP + CONTROLLED RF OUTPUT POWER VPC PCTL G1 G2 - IFB LTC4401-X H1 RF H2 4401 F04 RF DETECTOR DIRECTIONAL COUPLER 14dB to 20dB LOSS Figure 4. Closed-Loop Block Diagram The user agrees that this model is licensed from Linear Technology and agrees that the model may be used, loaned, given away or included in other model libraries as long as this notice and the model in its entirety and unchanged is included. No right to make derivative works or modifications to the model is granted hereby. All such rights are reserved. This model is provided as is. Linear Technology makes no warranty, either expressed or implied about the suitability or fitness of this model for any particular purpose. In no event will Linear Technology be liable for special, collateral, incidental or consequential damages in connection with or arising out of the use of this model. It should be remembered that models are a simplification of the actual circuit. 80 70 60 50 40 30 20 10 0 -10 -20 -30 -40 -50 -60 100 1k 180 RLOAD = 2k 160 CLOAD = 33pF 140 120 PHASE 100 80 60 GAIN 40 20 0 -20 -40 -60 -80 -100 10k 100k 1M 10M FREQUENCY (Hz) PHASE (DEG) In all cases, the current data sheet information is your final design guideline, and is the only performance guarantee. For further technical information, refer to individual device data sheets. Your feedback and suggestions on this model is appreciated. Linear Technology Corporation hereby grants the users of this model a nonexclusive, nontransferable license to use this model under the following conditions: VOLTAGE GAIN (dB) This model (Figure 6) is being supplied to LTC users as an aid to circuit designs. While the model reflects reasonably close similarity to corresponding devices in low frequency AC performance terms, its use is not suggested as a replacement for breadboarding. Simulation should be used as a forerunner or a supplement to traditional lab testing. 4401 F05 Figure 5. SPICE Model Open-Loop Gain and Phase Characteristics from RF to VPCA, PCTL < 80mV 4401fa 11 LTC4401-1/LTC4401-2 U W U U APPLICATIO S I FOR ATIO *LTC4401-X Low Frequency AC Spice Model* *July 11, 2001 *Main Network Description GGIN1 ND3 0 ND2 IFB 86E-6 GGXFB IFB 0 0 ND12 33E-6 GGX5 ND11 0 0 ND10 1E-6 GGX6 ND12 0 0 ND11 1E-6 GGX1 ND4 0 0 ND3 1E-6 GGX2 ND6 0 0 ND4 1E-6 GGX3 ND7 0 0 ND6 1E-6 GGX4 ND8 0 0 ND7 1E-6 EEX1 ND9 0 0 ND8 2 CCC1 ND3 0 75E-12 CCPCTL2 ND2 0 7E-12 CCPCTL1 ND1 0 13E-12 CCLINT VPCA 0 5E-12 CCLOAD VPCA 0 33E-12 CCFB1 IFB 0 2.4E-12 CCX5 ND11 0 16E-15 CCX6 ND12 0 1.2E-15 CCP ND10 0 28E-12 CCX2 ND6 0 8E-15 CCX3 ND7 0 32E-15 LLX1 ND5 0 65E-3 RR01 ND3 0 20E6 RRFILT ND2 ND1 44E3 RRPCTL1 PCTL ND1 51E3 RRPCTL2 ND1 0 38E3 RR9 VPCA ND9 50 RRLOAD VPCA 0 2E3 RRFB1 IFB 0 22E3 RRT RF 0 250 RRX5 ND11 0 1E6 RRX6 ND12 0 1E6 RRSDRF ND10 500 RRX1 ND4 ND5 1E6 RRX2 ND6 0 1E6 RRX3 ND7 0 1E6 RRX4 ND8 0 1E6 **Closed-loop feedback, comment-out VPCTLO, VRF, Adjust EFB gain to reflect external gain, currently set at 3X** *EFB RF 0 VPCA VIN 3 *VIN VIN 0 DC 0 AC 1 *VPCTLO PCTL 0 DC 0 **Open-loop connections, comment-out EFB, VIN and VPCTLO****** VPCTLO PCTL 0 DC 0 VRF RF 0 DC 0 AC 1 ******Add AC statement and print statement as required*** .AC DEC 50 100 1E7 *****for PSPICE only***** .OP .PROBE ************************* .END Figure 6. LTC4401-X Low Frequency AC SPICE Model 4401fa 12 LTC4401-1/LTC4401-2 U W U U APPLICATIO S I FOR ATIO PCTL RPCTL1 51E3 CPCTL1 13E-12 ND2 GIN1 + RFILT 44E3 RPCTL2 38E3 C PCTL2 7E-12 - 86E-6 GX1 + RO1 20E6 GM ND6 ND4 ND3 ND1 GM - CC1 75E-12 1E-6 RX1 1E6 ND5 GX2 + LX1 65E-3 - + RX2 1E6 GM 1E-6 - IFB 1E-6 GX4 + RX3 1E6 GM CX2 8E-15 ND8 ND7 GX3 RX4 1E6 GM - CX3 32E-15 1E-6 ND8 2X BUFFER RF ND11 RT 250 RX5 1E6 GM ND10 CP 28E-12 GX5 + RSD 500 - 1E-6 ND12 RX6 1E6 GM - CX5 16E-15 GX6 + 1E-6 33E-6 EX1 + RFB1 22E3 GM - CX6 1.2E-15 GXFB + R9 50 VAMP CFB1 2.4E-12 - 2 CLINT 5E-12 ND9 VPCA RLOAD 2E3 CLOAD 33E-12 4401 F07 Figure 7. LTC4401-X Low Frequency AC Model 4401fa 13 LTC4401-1/LTC4401-2 U PACKAGE DESCRIPTIO S6 Package 6-Lead Plastic TSOT-23 (Reference LTC DWG # 05-08-1636) 0.62 MAX 2.90 BSC (NOTE 4) 0.95 REF 1.22 REF 3.85 MAX 2.62 REF 1.4 MIN 2.80 BSC 1.50 - 1.75 (NOTE 4) PIN ONE ID RECOMMENDED SOLDER PAD LAYOUT PER IPC CALCULATOR 0.30 - 0.45 6 PLCS (NOTE 3) 0.95 BSC 0.80 - 0.90 0.20 BSC 0.01 - 0.10 1.00 MAX DATUM `A' 0.30 - 0.50 REF 0.09 - 0.20 (NOTE 3) 1.90 BSC S6 TSOT-23 0302 NOTE: 1. DIMENSIONS ARE IN MILLIMETERS 2. DRAWING NOT TO SCALE 3. DIMENSIONS ARE INCLUSIVE OF PLATING 4. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR 5. MOLD FLASH SHALL NOT EXCEED 0.254mm 6. JEDEC PACKAGE REFERENCE IS MO-193 4401fa 14 LTC4401-1/LTC4401-2 U PACKAGE DESCRIPTIO MS8 Package 8-Lead Plastic MSOP (Reference LTC DWG # 05-08-1660) 0.889 0.127 (.035 .005) 5.23 (.206) MIN 3.20 - 3.45 (.126 - .136) 0.42 0.038 (.0165 .0015) TYP 3.00 0.102 (.118 .004) (NOTE 3) 0.65 (.0256) BSC 8 7 6 5 0.52 (.0205) REF RECOMMENDED SOLDER PAD LAYOUT 0.254 (.010) 3.00 0.102 (.118 .004) (NOTE 4) 4.90 0.152 (.193 .006) DETAIL "A" 0 - 6 TYP GAUGE PLANE 0.53 0.152 (.021 .006) DETAIL "A" 1 2 3 4 1.10 (.043) MAX 0.86 (.034) REF 0.18 (.007) SEATING PLANE 0.22 - 0.38 (.009 - .015) TYP 0.65 (.0256) BSC 0.127 0.076 (.005 .003) MSOP (MS8) 0204 NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX 4401fa Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 15 LTC4401-1/LTC4401-2 U TYPICAL APPLICATION LTC4401-2 Dual Band Cellular Telephone Transmitter 68 33pF LTC4401-2 VIN VCC RF Li-Ion SHDN SHDN VPCA BSEL BSEL VPCB GND PCTL 0.1F 900MHz DIRECTIONAL COUPLER DIPLEXER RF PA 50 DAC 1.8GHz/ 1.9GHz RF PA 4401 TA03 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTC1503 Inductorless Step-Down DC/DC Converter 600kHz, Up to 100mA, 25% Higher Efficiency Than Linear Regulator LTC1555L-1.8 SIM Power Supply and Level Translator Generates 1.8V, 3V or 5V; >10kV ESD on All SIM Contact Pins LT 1615 Step-Up DC/DC Converter ThinSOT, Low 20A Quiescent Current, VIN as Low as 1V, 300mA IOUT LT1617 Inverting DC/DC Converter ThinSOT, Low 20A Quiescent Current, VIN as Low as 1V, 300mA IOUT LTC1682 Low Noise Charge Pump with LDO 60VRMS Output Noise, Small MSOP Package LTC1734 SOT-23 Li-Ion Battery Charger Up to 700mA Charge Current, Only Two External Components LT1761 Low Dropout, Low Noise Linear Regulator ThinSOT, 300mV Dropout at 100mA, 20VRMS Output Noise (10Hz to 100kHz) LTC1878 Step-Down DC/DC Converter Integrated Synchronous Operation, Up to 95% Efficiency, 1A Switch Current. LTC1911 Low Noise, Inductorless Buck Controller 2.7V VIN 5.5V, IOUT 250mA, 1.5MHz, 8-Pin MSOP LTC1928 Low Noise Charge Pump ThinSOT, 90VRMS Output Noise (100kHz BW), IOUT Up to 30mA LT1932 White LED Driver ThinSOT, 1.2MHz DC/DC Constant-Current LED Driver, Dimming Control LT1944 Step-Up DC/DC Converter Dual Output for LCD Bias, Low Quiescent Current of 20A, 1.2V VIN 15V LTC1986 SIM Power Supply ThinSOT, 3V and 5V, Ultralow Supply Current of 14A, <0.92cm2 PCB LTC3200 Low Noise Charge Pump 2MHz Switching Frequency Allows Small Size Capacitors, IOUT Up to 100mA LTC3202 Charge Pump for White LED 2.5% Less Input Current than Doubler Charge Pump, IOUT 125mA LTC3401 Step-Up DC/DC Converter Synchronous Rectification, Up to 97% Efficiency, 1A Switch Current, 3MHz LTC3402 Step-Up DC/DC Converter Synchronous Rectification, Up to 97% Efficiency, 2A Switch Current, 3MHz LTC3404 Step-Down DC/DC Converter 1.4MHz Synchronous Rectification, 10A Quiescent Current LTC3405 1.5MHz, 250mA ThinSOT Buck Converter Up to 96% Efficiency, 2.5V VIN 5.5V, No Schottky Diode LTC4400 RF Power Controller in ThinSOT 450kHz Loop BW and 45dB Dynamic Range LTC5505 RF Power Detector in ThinSOT >40dB Dynamic Range, 300MHz to 3GHz, Buffered Detector Output (R) 4401fa 16 Linear Technology Corporation LT/TP 0204 1K REV A * PRINTED IN THE USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com LINEAR TECHNOLOGY CORPORATION 2001