LM158,A-LM258,A Ky LM358.A LOW POWER DUAL OPERATIONAL AMPLIFIERS INTERNALLY FREQUENCY COMPENSATED LARGE DC VOLTAGE GAIN : 100dB WIDE BANDWIDTH (unity gain) : 1.1MHz (temperature compensated) a VERY LOW SUPPLY CURRENT/OP (500A) - ESSENTIALLY INDEPENDENT OF SUPPLY VOLTAGE = LOW INPUT BIAS CURRENT : 20nA N D DIPS $08 (temperature compensated) Plastic Pack Plastic Mi k a LOW INPUT OFFSET VOLTAGE : 2mV (Plastic Package) (Plastic Micropackage) a LOW INPUT OFFSET CURRENT : 2nA INPUT COMMON-MODE VOLTAGE RANGE INCLUDES GROUND DIFFERENTIAL INPUT VOLTAGE RANGE EQUAL TO THE POWER SUPPLY VOLTAGE p LARGE OUTPUT VOLTAGE SWING OV TO TSSOPs (Voc 1.5V) (Thin Shrink Small Outline Package) ORDER CODES Part Temperature Package Number Range N D P LM158,A 56C, +125G * * LM258,A 40C, +105G . . DESCRIPTION LM358,A 0C, +70C * * These circuits consist of two independent, high gain, Example : LM258N internally frequency compensated which were designed specifically to operate trom a single power . supply over a wide range of voltages. The low power PIN CONNECTIONS (top view) supply drain is independent of the magnitude of the power supply voltage. Application areas include transducer amplifiers, dc { TI | 8 gain blocks and all the conventional op-amp circuits which now can be more easily implementedin single 2 CH: rT] 7 power supply systems. For example, these circuits can be directly supplied with the standard + 5V sO <F 6 which is used in logic systems and will easily provide the required interface electronics without requiring aU HL 5 any additional power supply. In the linear mode the input common-mode voltage : 1 - Output 1 5 - Non-inverting input 2 range includes ground and the output voltage can 2 - Inverting input 1 6 - Inverting input 2 also swing to ground, even though operated trom 3 - Non-inverting input 1 7 - Quput 2 only a single power supply voltage. 4-Veo 8 - Vcc" June 1998 2LM158,A - LM258,A - LM358,A SCHEMATIC DIAGRAM (1/2 LM158) Voc i | ; Y) SLA 4A 100A ~ [ Q5 Cc C_ ae Inverti Ce nverting Q7 input Qi R ge Non-inverting an | Output input uipu Q13 for Qi2 a Q8 F* 7 G9 a 50nA Se = = Se pa Ee == GND ABSOLUTE MAXIMUM RATINGS Symbol Parameter LM158,A LM258,A LM358,A Unit Vcc Supply Voltage +32 +32 +32 Vv Vi Input Voltage 0.3 to +32 0.3 to +82 0.3 te +32 Vv Via Differential Input Voltage +32 +32 +32 Vv Cutput Short-circuit Duration - (note 2) Infinite Prat Power Dissipation 500 500 500 mW lin Input Current - (note 1) 50 50 50 mA Toper | Operating Free-air Temperature Range -55 to +125 40 to +105 0 to +70 C Taig Storage Temperature Range -65 to +150 65 to +150 65 to +150 C 212 <i)LM158,A - LM258,A - LM358,A ELECTRICAL CHARACTERISTICS Voe* =+45V, Veco = Ground, Vo = 1.4V, Tamb = 25C {unless otherwise specified) Symbol Parameter LM158A-LM258A LM358A LM158-LM258 LM358 Unit Min. Typ. Max. Min. | Typ. Vio Input Offset Voltage - (note 3) Tamo = 25C LM158, LM258 LM158A Tinin. S Tamo & Tmax. LM158, LM258 1 mV 3 2 ? 5 2 4 a ? lo Input Offset Gurrent Tambo = 25C Tmin. S Tamo <= Tmax. nA 10 2 30 30 40 Input Bias Current - (note 4) Tam = G Tmin. S Tamo <= Tmax. 20 nA 50 20 106 Av Large Signal Voltage Gain (Veco = +15V, Ri = 2kQ, Vo = 1.4V to 11.4V) Tamp = 25C Twin. < Tamb < Tmax. 50 25 100 VvimV 50 100 25 SVR Supply Voltage Rejection Ratio (Rg = 10kQ) (Vcc* = 5 to 30V) Tama = 25C Tinin. S Tambo <= Tmax. 65 100 dB 65 100 lec Supply Current, all Amp, no Load Veo = +5V, Tin. = Tamb = Tmax. Voc = +30V, Tmin. < Tamb = Tmax. 0.7 mA 1.2 07 1.2 Vicm Input Common Mode Voltage Range (Voc = +30) - (note 6) Tambo = 25C Tinin. = Tame = Tmax. Vec*-1.5 Vec-2 Vec*-1.5 0 Vec-2 0 CMR Gommon-mede Rejection Ratio (Rg = 10k) Tame = 25C Tmin. = Tamb = Tmax. 70 60 85 dB 70 85 60 Isouree Output Current Source (Vcc = +15V, Vo = 2V, Vig = +1V) 20 40 mA 60 20 40 60 Isink Output Current Sink (Vig = -1V) Veco = +15V, Vo = 2V Veco = +15V, Vo = 4+0.2V a No 20 50 10 20 12 50 Vopr Output Voltage Swing (RL = 2k) Tambo = 25C Timin. S Tambo = Tmax. oo </52 Voc*-1.5 0 Vec-2 0 Voco*-1.5 Vec-2 Vou High Level Output Voltage (Vcc = 30V)} Tambo = 25C Re = 2ko Tinin. = Tamb s Tmax. Tamo = 25C Tinin. < Tamb s Tmax. RL = 10kQ 26 26 ef 27 27 28 26 27 26 ef 28 27 VoL Low Level Output Voltage (RL = 10k) Tamo = 25C Timin. Tamo = Tmax. mV 20 5 20 20 20 SR Slew Rate (Voc = 15V, V; = 0.5 to 3V, RL= 2kQ, GC. = 100pF, unity gain) 0.3 0.6 Vins 0.3 0.6 GBP Gain Bandwidth Product (Voc = 30V, f = 100kHz, Vin = 10mV, Ri = 2k, OL = 100pF) 0.7 1.1 MHz 0.7 1.1 THD Total Harmonic Distortion (i = 1kHz, Ay = 20dB, Ry = 2k, Voc = 30V, GL = 100pF, Vo = 2 pp) 0.02 % 0.02 en Equivalent Input Noise voltage (i = 1kHz, Rs = 1000, Vcc = 30V) 55 55 VHz 4) 3/12LM158,A - LM258,A - LM358,A ELECTRICAL CHARACTERISTICS (continued) LM158A LM158 Symbol Parameter A tes Unit Min. Typ. Max. Min. Typ. Max. DVio Input Offset Voltage Drift 7 15 7 30 LVPG Dlio Input Offset Current Drift 10 200 10 300 pAfG Vor/Voe Channel Separation (note 5) dB kHz < f <= 20kKHz 120 120 Notes: 1. This input current only exist when the voltage at any of the input leads is driven negative. It is due to the collec- tor-base junction of the input PNP transistor becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is also NPN parasitic action on the IC chip. This transistor action can cause the output voltages of the Op-amps to go to the Vcc voltage level (or to ground for a large overdrive) for the time duration that an input is driven negative. This is net destructive and normal output will set up again for input voltage higher than -0.3V. 2. Short-circuits from the output to Vcc can cause excessive heating if Vcc > 15V. The maximum output current is approximatively 40mA independent of the magnitude of Vcc. Destructive dissipation can result from simultaneous short-circuits on all amplifiers. 3. Vo = 1.4V, Rg = 02, BV < Veo < 30V, 0 < Vic < Voc 1.5V. 4. The direction of the input current is out of the IC. This currant is essentially constant, independent of the state of the output so no loading change exists on the input lines. 5. Due to the proximity of external components insure that coupling is not originating via stray capacitance between these external parts. This typically can be detected as this type of capacitance increases at higher frequences. 6. The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the common-mode vollaga range is Vcc 1.5V. But either or both inputs can go to +32V without damage. OPEN LOOP FREQUENCY RESPONSE (NCTE 3) LARGE SIGNAL FREQUENCY RESPONSE 140 20 120 . _ oo o 3, 100 > 15 Z g <t gj (8 \ = ra} 60 SS -55C <Tamp < 125C Y 10 << \ 5 3% NS z > N 3 5 201 Voc =+10to+ 15V a -65C <Tamb < +125C N 0 | | | 0 4H2 10 610 100 1k 10k 100k iM 10M 4k 40k 400k 1M FREQUENCY (Hz) FREQUENCY (Hz) VGLAGE FOLLOWER PULSE RESPONSE QUTPUT CHARACTERISTICS 4 10 > VCC = +5V > RL< 2k E= 3 : _ VCC = +15V > W VCC = +15 S VOC = 430Y St 2 Ww O45 Oo 4 5 < > 1 A Oo a > 5 _ 3 A 0.4 *alo = 5 3 0 o I af 1 F- z 5 0.01 > 0,001 0,01 01 4 10 100 TIME ( 8) OUTPUT SINK CURRENT (mA) <i)LM158,A - LM258,A - LM358,A VOLTAGE FOLLOWER PULSSE RESPONSE OUTPUT VOLTAGE (mV) INPUT CURRENT (mA) INPUT VOLTAGE (V3 4) (SMALL SIGNAL} 500 r |. 71 450 60 al 50pF 400 3 tC {\ Input / 350 Output 300 Lo Tamb = +25C 250 Yoc L #0 \ 0 1 2 3 4 5 6 t 8 TIME ( s) INPUT CURRENT (Note 1) 90 80 Vj=0V 70 60 50 40 30 20 10 0 5 -35 -15 5 25 45 65 65 105 125 TEMPERATURE (C) INPUT VOLTAGE RANGE 15 10 NN Negative YY A Pasitive 0 / /| 5 10 POWER SUPPLY VOLTAGE (V) 15 OUTPUT VOLTAGE REFERENCED TO Vect (V) OUTPUT GURRENT (mA) SUPPLY CURRENT (mA) 55 -35 -15 5 OUTPUT CHARACTERISTICS 8 Tere T Tor T Le Vec 7b 4 6LVcci2 BL lo 4L = * ri ob btm tb vein Independent of Vcc 3 T TOTTI Tt Pirin Tamb = 125C ! 2 4 : 0,001 0,01 0,1 1 10 100 OUTPUT SOURCE CURRENT (mA) CURRENT LIMITING (Note 1} 25 45 65 85 105 125 TEMPERATURE (C) SUPPLY CURRENT t T vec mA lb . Tamb = 0C to +125C La Le 4 Tamb = -55C l l 0 POSITIVE SUPPLY VOLTAGE (V) 10 20 30 5/12LM158,A - LM258,A - LM358,A 160 100 R , = 20k z D 100 = Ss ~ 75 z Zz o R, =2k e = oY 80 L x 50 a - Ee en a 40 a 25 > = amb 25C 0 10 20 30 40 0 10 20 30 POSITIVE SUPPLY VOLTAGE (V) POSITIVE SUPPLY VOLTAGE (V) 160 S45 _ R | = 20k = 1.35 120 Q 12 = Qa Z S 1.08 . uw 80 + 0.75 o) x 0. c O 06 D 40 = 0.45 q 0.3 = 0.15 <= 0 0 10 20 30 O -55-35-15 5 254565 85 105 125 POSITIVE SUPPLY VOLTAGE (V) TEMPERATURE (C) g g 5 115 5 115 FE 110 E 110 105 105 S 100 S 100 95 5 95 3 90 90 85 85 7 80 80 o 75 2 5 2 70 Zz 70 i 65 S 65 S 6055-35-15 5 254565 85 105 125 = 60-55-35-15 5 25 45 65 85 105 125 a TEMPERATURE (C) 0 TEMPERATURE (C) 6/12 kyLM158,A - LM258,A - LM358,A TYPICAL APPLICATIONS (single supply voltage) Vcc = +5Vpc AG COUPLED INVERTING AMPLIFIER AG COUPLED NON-INVERTING AMPLIFIER fas shown Ay = -10) | i a eo _ Ri 10kQ e| Ril R2 100kQ. 1MQ A,=14+ 82 v RA (as shown Ay=11) ci O4uF Cc) 8 NON-INVERTING DC AMPLIFIER DG SUMMING AMPLIFIER R2 Ay =1424 Vv T+ (As shown Ay = 101} [ e, 100kQ @o = 61+ 2 - G3 - e4 where (e; + eo) > (eg + 24) to keep ep > OV 4) 712LM158,A - LM258,A - LM358,A HIGH INPUT Z, DG DIFFERENTIAL AMPLIFIER USING SYMMETRICAL AMPLIFIERS TO REDUCE INPUT CURRENT if Ry = Rs and R3 = Ry = Re = Re eo 114 BY (e2- @1) As shown @po = 101 (e2 - e1). Input current compensation HIGH INPUT Z ADJUSTABLE GAIN DCG INSTRUMENTATION AMPLIFIER LOW DRIFT PEAK DETECTOR Ri 100k0 i__] + ey Go + R2 Gain adjust 2kQ R5 100k2 eo" if Ry = Re and Ra = Ry = Rg = R7 2R eo= [1+ 35] (e2-e1) 2 As shown @o = 101 (ee - e1) OB - Input current lp compensation 82 <i)LM158,A - LM258,A - LM358,A ACTIVE BAND-PASS FILTER +V1 R2 100k2 R3 100ks3 Fo = 1kHz Q=50 Ay = 100 (40dB) Ri 100k22 Ci ~ 1) lL. LM158 RS ha A70kKQ 10M 1/2 LM158 ] C2 R + 330pF 6 470k - Lt OVo 1/2 R7 LM158 100k93 + ft Vec R 100ka3 4) 9/12LM158,A - LM258,A - LM358,A PACKAGE MECHANICAL DATA 8 PINS - PLASTIC DIP 4 | \ {UT 0 S |; _ I 4 bi B i | | b E T 6 63 Zz Zz D OCI Ti 8 5 Le 1 4 LI LI LJ u . Millimeters Inches Dim. Min. Typ. Max. Min. Typ. Max. A 3.32 0.131 al 0.51 0.020 B 1.15 1.65 0.045 0.065 b 0.356 0.55 0.014 0.022 b1 0.204 0.304 0.008 0.012 D 10.92 0.430 E 7.95 9.75 0.313 0.384 e 2.54 0.100 e3 7.62 0.300 e4 7.62 0.300 F 6.6 0260 i 5.08 0.200 L 3.18 3.81 0.125 0.150 Z 1.52 0.060 10/12 <i) PM-DIP&.EPS DIP&.TBLLM158,A - LM258,A - LM358,A PACKAGE MECHANICAL DATA 8 PINS - PLASTIC MICROPAGKAGE (SO) L of 2 Goma Jc 3| =< ; ri a0 wat WI 1 . $ a = e3 D tt and [] iL a Ts q Do oo Uo : Millimeters Inches Dim. Min. Typ. Max. Min. Typ. Max. A 1.75 0.069 al 0.1 0.25 0.004 0.010 a2 1.65 0.065 a3 0.65 0.85 0.026 0.033 b 0.35 0.48 0.014 0.019 b1 0.19 0.25 0.007 0.010 CG 0.25 0.5 0.010 0.020 cl 45 (typ.) D 48 5.0 0.189 0.197 E 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 3.81 0.150 F 3.8 4.0 0.150 0.157 L 0.4 1.27 0.016 0.050 M 0.6 0.024 s 8 (max.) 4) 1112 PM-SO8.EPS SO8.TBLLM158,A - LM258,A - LM358,A PACKAGE MECHANICAL DATA 8 PINS - THIN SHRINK SMALL OUTLINE PACKAGE D et SEINE? == ' } He - SS : . i Page : SLATS SLANE pw a aewrecanon / Dim. Millimeters Inches Min. Typ. Max. Min. Typ. Max. A 1.20 0.05 Al 0.05 0.15 0.01 0.006 Ae 0.80 1.00 1.05 0.031 0.039 0.041 b 0.19 0.30 0.007 0.15 c 0.09 0.20 0.003 0.012 D 2.90 3.00 3.10 0.114 0.118 0.122 E 6.40 0.252 Ei 4.30 4.40 4.50 0.169 0.173 0.177 e 0.65 0.025 k O 8 o 8 | 0.50 0.60 0.75 0.09 0.0236 0.030 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifi- cations mentioned in this publication are subject te change without notice. This publication supersedes and replaces all infor- mation previously supplied. STMicroelectronics products are not authorized for use as critical components in life support de- vices or systems without express written approval of STMicroelectronics. The ST logo is a trademark of STMicroelectronics 1998 STMicreelectronics Printed in Italy All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - France - Germany - Italy - Japan - Korea - Malaysia - Malta - Mexico - Morocco The Netherlands - Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. 122 Sy ORDER GODE