DO NOT
SCALE FROM
THIS PRINT
ISDF-XX-D-X
No OF POSITIONS
-02 THRU -50
(PER ROW)
ROW SPECIFICATION
-D: DOUBLE ROW
NOTCH SPECIFICATION
LEAVE BLANK: NO NOTCH
-C: CHAMFER (SEE SHEET 2,
FIG 2) (7 POSITION ONLY)
-L: FRICTION LOCK
(SEE SHEET 2, FIG 3)
(AVAILABLE ON POS 10 - 30)
-R: RETENTION LATCH (AVAILABLE
ON POS -05 THRU -30)
(SEE SHEET 3, FIG 4)
(SEE NOTE 11)
((No OF POS x .050) + .015)
.025
(TYP)
.180
.250
.020
(TYP)
R
.001
.1450
.1200
(TOL NON-ACCUM)
(No OF POS x .050) - .050
"A"
"A" C
L
C
L
.002
.005
SEE NOTE 3
A
C1
FIG. 1
ISDF-10-D-X SHOWN
SEE NOTE 2
.0800
±.0020
.050
.0260
.0420
R
.001
"B"
"B"
'C'
SECTION "A"-"A"
C
L
C2
C3
.003
'D'
"F"
"F"
02
01 03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
SEE NOTE 8
.440
.4260 .415
.058
.077
.103
.0150
REF
.0430
.0525
R
.005
TYP
.0500
'E'
SECTION "B"-"B"
C5
C4
C6
.003
.050
.030
.030
.033
SEE NOTE 4
.2180
.0410
SECTION "F"-"F"
C7
C8
.070
C
L
SEE NOTE 7
C
K
SHEET OF
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS ANGLES
.XX:
.01 [.3] 2
.XXX:
.003 [.08]
.XXXX:
.0015 [.038]
MATERIAL:
.050" CL CRIMP WIRE SOCKET INSULATOR
BY:
ISDF-XX-D-X
DWG. NO.
DESCRIPTION:
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
BRATCHER
5/4/2005
3
1
SHEET SCALE: 4:1
VECTRA S475, COLOR: BLACK
F:\DWG\MISC\MKTG\ISDF-XX-D-X-MKT.SLDDRW
NOTES:
1. REPRESENTS A CRITICAL DIMENSION.
2. SAMTEC LOGOS SHALL APPEAR AT LOCATIONS ON SURFACE SHOWN,
APPROXIMATELY .075 x .055 (BOTH SIDES).
3. ALL MULTIPLE CAVITY MOLDS SHALL IDENTIFY EACH CAVITY WITH A LETTER
DESIGNATION LOCATED WHERE SHOWN.
4. IDENTIFICATION MARKS NOT TO PROTRUDE BEYOND .001 ABOVE THE SURFACE
OF THE INSULATOR MATERIAL.
5. MOLDED SURFACES SHALL BE CONSISTENT AND SMOOTH. SURFACES TO BE
FREE OF SCATCHES, NICKS, SINK AREAS, VOIDS OR OTHER BLEMISHES.
6. PART TO BE SYMMETRIC ABOUT THE CENTERLINE WITHIN +/-.0015, UNLESS
OTHERWISE STATED.
7. GATE PADS MUST BE RECESSED .005.
8. SPECIFIED POSITIONS TO BE IDENTIFIED WHERE SHOWN (NOTE 4 APPLIES).
9. R.005 OPTIONAL.
10. POSITIONS -10 THROUGH -24 WILL HAVE ONLY ONE LATCH LOCK AT DIMENSION SHOWN;
POSITIONS -25 THROUGH -30 WILL HAVE TWO LATCH LOCKS AT DIMENSION SHOWN.
11. OPTION NOT FOR SALE. FOR RETENTION LATCH FEATURE, SEE ISDF-XX-D-M PRINT.
MAX REGRIND: 50%
MAX FLASH ALLOWED: .002
MAX GATE VESTIGE: .004
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail: info@SAMTEC.com code: 55322
REVISION K
.040
SQ
.0120
.0220
SQ
90°
.0350
-
.0010
+
.0015
SQ
DETAIL 'C'
SCALE 16 : 1
C9
DETAIL 'D'
SCALE 16 : 1
30°
R
.0025
(TYP)
.0075
DETAIL 'E'
SCALE 16 : 1
30°
.035
FIG. 2
ISDF-07-D-C SHOWN
SAME AS FIG. 1 UNLESS SPECIFIED
01 03 05 07 09 11 13
02 04 06 08 10 12 14
.3050
(TYP)
(SEE NOTE 10)
.1000
(TYP)
"G"
"G"
FIG. 3
ISDF-25-D-L SHOWN
SAME AS FIG. 1 EXCEPT AS SHOWN
.0350
(TYP)
R
.025
(TYP)
R
.010
(TYP)
.027
-
.000
+
.003
(TYP)
SECTION "G"-"G"
SCALE 4 : 1
SHEET OF
.050" CL CRIMP WIRE SOCKET INSULATOR
BY:
ISDF-XX-D-X
DWG. NO.
DESCRIPTION:
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
BRATCHER
5/4/2005
3
2
SHEET SCALE: 1:0.166667
F:\DWG\MISC\MKTG\ISDF-XX-D-X-MKT.SLDDRW
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail: info@SAMTEC.com code: 55322
REVISION K
.440
REF
((No OF POS x .050) + .015)
-
.002
+
.000
.020
"H"
"H"
'J'
FIG. 4
-R: RETENTION LATCH OPTION (SEE NOTE 11)
(ISDF-05-D-R SHOWN)
(SAME AS FIG. 1 EXCEPT AS SHOWN)
C11
.1740
.0300
.065
.1480
.360
±.002
8°
SECTION "H"-"H"
C
L
C9
((No OF POS x .050) + .145)
-
.005
+
.002
((No OF POS x .0500) + .0700)
.002
'K'
C
L
C10
.015
45°
X
(TYP)
.0140
±.0010
R
.004
(4 PLCS)
R
.0020
(TYP)
.0095
-
.0005
+
.0010
DETAIL 'K'
SCALE 10 : 1
30°
(TYP)
.005
±.002
(TYP)
.0270
45°
.0023
.0190
15°
DETAIL 'J'
SCALE 12 : 1
SHEET OF
.050" CL CRIMP WIRE SOCKET INSULATOR
BY:
ISDF-XX-D-X
DWG. NO.
DESCRIPTION:
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
BRATCHER
5/4/2005
3
3
SHEET SCALE: 6:1
F:\DWG\MISC\MKTG\ISDF-XX-D-X-MKT.SLDDRW
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail: info@SAMTEC.com code: 55322
REVISION K
