IDT5V2528/A 2.5 / 3.3V PHASE-LOCK LOOP CLOCK DRIVER INDUSTRIAL TEMPERATURE RANGE 2.5V / 3.3V PHASE-LOCK LOOP CLOCK DRIVER ZERO DELAY BUFFER FEATURES: * * * * The IDT5V2528 inputs, PLL core, Y0, Y1, and FBOUT buffers operate from the 3.3V VDD and AVDD power supply pins. One bank of ten outputs provide low-skew, low-jitter copies of CLK. Of the ten outputs, up to seven may be configured for 2.5V or 3.3V LVTTL outputs. The number of 2.5V outputs is controlled by 3-level input signals G_Ctrl and T_Ctrl, and by connecting the appropriate VDDQ pins to 2.5V or 3.3V. The 3-level input signals may be hard-wired to high-mid-low levels. Output signal duty cycles are adjusted to 50 percent, independent of the duty cycle at CLK. The outputs can be enabled or disabled via the G_Ctrl input. When the G_Ctrl input is mid or high, the outputs switch in phase and frequency with CLK; when the G_Ctrl is low, all outputs (except FBOUT) are disabled to the logic-low state. Unlike many products containing PLLs, the IDT5V2528 does not require external RC networks. The loop filter for the PLL is included on-chip, minimizing component count, board space, and cost. Because it is based on PLL circuitry, the IDT5V2528 requires a stabilization time to achieve phase lock of the feedback signal to the reference signal. This stabilization time is required, following power up and application of a fixed-frequency, fixed-phase signal at CLK, as well as following any changes to the PLL reference or feedback signals. The PLL can be bypassed for test purposes by strapping AVDD to ground. Operates at 3.3V VDD/AVDD and 2.5V/3.3V VDDQ 1:10 fanout 3-level inputs for output control External feedback (FBIN) pin is used to synchronize the outputs to the clock input signal No external RC network required for PLL loop stability Configurable 2.5V or 3.3V LVTTL outputs tPD Phase Error at 100MHz to 166MHz: 150ps Jitter (peak-to-peak) at 133MHz and 166MHz: 75ps Spread spectrum compatible Operating Frequency: - Std: 25MHz to 140MHz - A: 25MHz to 167MHz Available in TSSOP package * * * * * * * IDT5V2528/A DESCRIPTION: The IDT5V2528 is a high performance, low-skew, low-jitter, phase-lock loop (PLL) clock driver. It uses a PLL to precisely align, in both frequency and phase, the feedback (FBOUT) output to the clock (CLK) input signal. FUNCTIONAL BLOCK DIAGRAM 28 G_Ctrl T_Ctrl 3 1 TY0, VDDQ pin 4 26 TY1, VDDQ pin 25 24 TY2, VDDQ pin 25 MODE SELECT 17 TY3, VDDQ pin 15 16 TY4, VDDQ pin 15 13 TY5, VDDQ pin 11 12 CLK 10 6 TY7, VDDQ pin 11 PLL FBIN TY6, VDDQ pin 11 20 7 Y0, VDD pin 21 19 AVDD Y1, VDD pin 21 5 22 FBOUT, VDD pin 21 The IDT logo is a registered trademark of Integrated Device Technology, Inc. INDUSTRIAL TEMPERATURE RANGE JUNE 2003 1 c 2002 Integrated Device Technology, Inc. DSC 5971/11 IDT5V2528/A 2.5 / 3.3V PHASE-LOCK LOOP CLOCK DRIVER INDUSTRIAL TEMPERATURE RANGE ABSOLUTE MAXIMUM RATINGS(1) PIN CONFIGURATION Symbol Rating Max. Unit VDD, VDDQ, AVDD Supply Voltage Range -0.5 to +4.6 V T_Ctrl 1 28 G_Ctrl VI (2) Input Voltage Range -0.5 to +5.5 V GND 2 27 GND VO(2) Voltage Range applied to any -0.5 to V TY0 3 26 TY1 Input Clamp Current -50 mA Output Clamp Current 50 mA Continuous Output Current 50 mA 200 mA output in the HIGH or LOW state VDDQ 4 25 VDDQ IIK (VI < 0) AVDD 5 24 TY2 IOK VDD+0.5 (VO < 0 or VO > VDD) CLK 6 23 GND FBIN 7 22 FBOUT AGND 8 21 VDD VDD or GND Continuous Current GND 9 20 Y0 TSTG Storage Temperature Range TY7 10 19 Y1 TJ Junction Temperature VDDQ 11 18 GND TY6 12 17 TY3 TY5 13 16 TY4 GND 14 15 VDDQ IO (VO = 0 to VDD) -65 to +150 C +150 C NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 3. The maximum package power dissipation is calculated using a junction temperature TSSOP TOP VIEW of 150C and a board trace length of 750 mils. CAPACITANCE(1) Symbol CIN Description Min Typ. Max. Unit Input Capacitance -- 5 -- pF -- 6 -- pF -- -- 20 -- -- pF VI = VDD or GND CO Output Capacitance VI = VDD or GND CL Load Capacitance 2.5V outputs 3.3V outputs 30 NOTE: 1. Unused inputs must be held HIGH or LOW to prevent them from floating. RECOMMENDED OPERATING RANGE Symbol Description VDD, AVDD (1) Power Supply Voltage VDDQ (1) Power Supply Voltage TA 2.5V Outputs 3.3V Outputs Ambient Operating Temperature Min. Typ. Max. Unit 3 3.3 3.6 V 2.3 3 2.5 3.3 2.7 3.6 V -40 +25 +85 C NOTE: 1. All power supplies should operate in tandem. If VDD or VDDQ is at a maximum, then VDDQ or VDD (respectively) should be at maximum, and vice-versa. 2 IDT5V2528/A 2.5 / 3.3V PHASE-LOCK LOOP CLOCK DRIVER INDUSTRIAL TEMPERATURE RANGE PIN DESCRIPTION Terminal Name No. Type Description CLK(1) 6 I Clock input FBIN 7 I Feedback input G_Ctrl(2) 28 3-level 3-level input for 2.5V / 3.3V Output Select/ Output bank enable. When G_Ctrl is LOW, all outputs except FBOUT are disabled to a logic-LOW state. When G_Ctrl is MID or HIGH, all outputs are enabled and switch at the same frequency as CLK (see OUTPUT SELECTION table). T_Ctrl(2) 1 3-level FBOUT 22 O Feedback output 3, 10, 12, 13, O 2.5V or 3.3V Clock outputs. 1, 2, 3, 5, or 7 of these outputs may be selected as 2.5V outputs (see OUTPUT SELECTION table). O 3.3V Clock Outputs TY (7:0) 3-level input for 2.5V / 3.3V Output Select (see OUTPUT SELECTION table) 16, 17, 24, 26 Y (1:0) 19, 20 AVDD(3) 5 Power 3.3V Analog power supply. AVDD provides the power reference for the analog circuitry. AGND 8 Ground Analog ground. AGND provides the ground reference for the analog circuitry. VDD 21 Power 3.3V Power supply VDDQ 4, 11, 15, 25 Power 2.5V or 3.3V Power supply for TY outputs GND 2, 9, 14, 18 Ground Ground 23, 27 NOTES: 1. CLK must have a fixed frequency and fixed phase for the PLL to obtain phase lock. Once the circuit is powered up and a valid CLK signal is applied, a stabilization time of 1ms is required for the PLL to phase lock the feedback signal to the reference signal. 2. 3-level inputs will float to MID logic level if left unconnected. 3. AVDD can be used to bypass the PLL for test purposes. When AVDD is strapped to ground, PLL is bypassed and CLK is buffered directly to the outputs. STATIC FUNCTION TABLE (AVDD = 0V)(1) G_Ctrl L L Inputs T_Ctrl X X see OUTPUT SELECTION table CLK L H H L running TY(7:0) L L H L running Outputs Y(1:0) L L H L running OUTPUT SELECTION FBOUT L H H L running NOTE: 1. AVDD should be powered up along with VDD, before setting AVDD to ground, to put the control pins in a valid state. DYNAMIC FUNCTION TABLE (AVDD = 3.3V) Inputs G_Ctrl T_Ctrl L X L X see OUTPUT SELECTION table CLK L H L H TY(7:0) L L L H Outputs Y(1:0) L L L H FBOUT L H L H 3 G_Ctrl M T_Ctrl L M M M H H L H M H H TY(7:0) TY0 (2.5V) TY1 - TY7 (3.3V) TY1, TY2 (2.5V) TY0, TY3 - TY7 (3.3V) TY0 - TY2 (2.5V) TY3 - TY7 (3.3V) TY0 - TY4 (2.5V) TY5 - TY7 (3.3V) TY1 - TY7 (2.5V) TY0 (3.3V) TYo - TY7 (3.3V) VDDQ Configuration Pin 4 (2.5V) Pins 11, 15, 25 (3.3V) Pin 25 (2.5V) Pins 4, 11, 15 (3.3V) Pins 4, 25 (2.5V) Pins 11, 15 (3.3V) Pins 4, 15, 25 (2.5V) Pin 11 (3.3V) Pins 11, 15, 25 (2.5V) Pin 4 (3.3V) Pins 4, 11, 15, 25 (3.3V) IDT5V2528/A 2.5 / 3.3V PHASE-LOCK LOOP CLOCK DRIVER INDUSTRIAL TEMPERATURE RANGE DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE Symbol VIK VIH VIL VIHH VIMM VILL VOH VOH VOL VOL I3 II Parameter Input Clamp Voltage Input HIGH Level Input LOW Level Input HIGH Voltage Level(2) Input MID Voltage Level(2) Input LOW Voltage Level(2) Output HIGH Voltage Level (3.3V Outputs) Output HIGH Voltage Level (2.5V Outputs) Output LOW Voltage Level (3.3V Outputs) Output LOW Voltage Level (2.5V Outputs) 3-Level Input DC Current (G_Ctrl, T_Ctrl) Input Current Test Conditions II = -18mA CLK, FBIN CLK, FBIN 3-Level Inputs Only 3-Level Inputs Only 3-Level Inputs Only IOH = -100A IOH = -12mA IOH = -100A IOH = -12mA IOL = 100A IOL = 12mA IOL = 100A IOL = 12mA VIN = VDD VIN = VDD/2 VIN = GND VI = VDD or GND Min. Typ.(1) 2 VDD - 0.6 VDD/2 - 0.3 VDD - 0.2 2.4 VDD - 0.1 2 HIGH Level MID Level LOW Level -50 -200 Max - 1.2 Unit V V 0.8 V V VDD/2 + 0.3 V 0.6 V V V V 0.2 0.4 0.1 0.4 +200 +50 A 5 A V NOTES: 1. For conditions shown as Min or Max, use the appropriate value specified under recommended operating conditions. 2. These inputs are normally wired to VDD, GND, or left floating. Internal termination resistors bias floating inputs to VDD/2. If these inputs are switched, the function and timing of the outputs may be glitched, and the PLL may require an additional tLOCK time before all datasheet limits are achieved. POWER SUPPLY CHARACTERISTICS Symbol IDDPD IDDA IDD IDDD Parameter Power Down Supply Current AVDD Supply Current Dynamic Power Supply Current Dynamic Power Supply Current per Output Test Conditions VDD = 3.6, VDDQ = 2.7V / 3.3V, AVDD = 0V VDD = AVDD = 3.6V, VDDQ = 2.7V / 3.3V, CLK = 0 or VDD VDD = AVDD = 3.6V, VDDQ = 2.7V / 3.3V, CL = 0pF VDD = AVDD = VDDQ = 3.6V CL = 30pF, CLK = 100MHz VDD = AVDD = 3.6V, VDDQ = 2.7V CL = 20pF, CLK = 100MHz NOTE: 1. For nominal voltage and temperature. 4 Typ.(1) 8 3.5 500 15 Max 40 10 -- -- 12 -- Unit A mA A/MHz mA IDT5V2528/A 2.5 / 3.3V PHASE-LOCK LOOP CLOCK DRIVER INDUSTRIAL TEMPERATURE RANGE INPUT TIMING REQUIREMENTS OVER OPERATING RANGE 5V2528 Min Clock frequency fCLOCK Input clock duty cycle Min Max Units MHz 25 140 25 167 40% 60% 40% 60% Stabilization time(1) tLOCK 5V2528A Max 1 1 ms NOTE: 1.Time required for the integrated PLL circuit to obtain phase lock of its feedback signal to its reference signal. For phase lock to be obtained, a fixed-frequency, fixed-phase reference signal must be present at CLK. Until phase lock is obtained, the specifications for propagation delay, skew, and jitter parameters given in the switching characteristics table are not applicable. SWITCHING CHARACTERISTICS OVER OPERATING RANGE - 5V2528(1) Symbol tPHASE error tPHASE error - jitter(3) tSK1(0)(4) tSK2(0)(4) tSK3(0)(4,5) tJ tR tF tR tF Parameter(2) Phase Error from Rising Edge CLK to Rising Edge FBIN (100MHz-133MHz) Phase Error minus Jitter from Rising Edge CLK to Rising Edge FBIN (133MHz) Output Skew between 3.3V Outputs Output Skew between 2.5V Outputs Output Skew between 2.5V and 3.3V Outputs Cycle-to-Cycle Output Jitter (Peak-to-Peak) at 133MHz Duty Cycle Output Rise Time for 3.3V Outputs (20% to 80%) Output Fall Time for 3.3V Outputs (20% to 80%) Output Rise Time for 2.5V Outputs (20% to 80%) Output Fall Time for 2.5V Outputs (20% to 80%) Min. -150 -50 -- -- -- -75 45 0.8 0.8 0.5 0.5 Typ. -- -- -- -- -- -- -- -- -- -- -- Max. 150 50 150 150 200 75 55 2.1 2.1 1.5 1.5 Unit ps ps ps ps ps ps % ns ns ns ns SWITCHING CHARACTERISTICS OVER OPERATING RANGE - 5V2528A(1) Symbol tPHASE error tPHASE error - jitter(3) tSK1(0)(4) tSK2(0)(4) tSK3(0)(4,5) tJ tR tF tR tF Parameter(2) Phase Error from Rising Edge CLK to Rising Edge FBIN (100MHz-166MHz) Phase Error minus Jitter from Rising Edge CLK to Rising Edge FBIN (166MHz) Output Skew between 3.3V Outputs Output Skew between 2.5V Outputs Output Skew between 2.5V and 3.3V Outputs 25MHz to 133MHz 133MHz to 166MHz Cycle-to-Cycle Output Jitter (Peak-to-Peak) at 166MHz Duty Cycle Output Rise Time for 3.3V Outputs (20% to 80%) Output Fall Time for 3.3V Outputs (20% to 80%) Output Rise Time for 2.5V Outputs (20% to 80%) Output Fall Time for 2.5V Outputs (20% to 80%) Min. -150 -50 -- -- -- -- -75 45 0.8 0.8 0.5 0.5 NOTES: 1. All parameters are measured with the following load conditions: 30pF || 500 for 3.3V outputs and 20pF || 500 for 2.5V outputs. 2. The specifications for parameters in this table are applicable only after any appropriate stabilization time has elapsed. 3. Phase error does not include jitter. 4. All skew parameters are only valid for equal loading of all outputs. 5. Measured for VDDQ = 2.3V and 3V, 2.5V and 3.3V, or 2.7V and 3.6V. 5 Typ. -- -- -- -- -- -- -- -- -- -- -- -- Max. 150 50 150 150 200 250 75 55 2.1 2.1 1.5 1.5 Unit ps ps ps ps ps ps % ns ns ns ns IDT5V2528/A 2.5 / 3.3V PHASE-LOCK LOOP CLOCK DRIVER INDUSTRIAL TEMPERATURE RANGE TEST CIRCUIT AND VOLTAGE WAVEFORMS From Output Under Test From Output Under Test 500 CL=30pF(2) 500 CL=20pF(2) Test Circuit for 3.3V Outputs Test Circuit for 2.5V Outputs VDD/2 CLK FBIN VDD/2 tPHASE ERROR CLK Y, TY IDT5V2528/A CL (2) CF (4) FBIN FBOUT 500 on each Y, TY output FBOUT or Any Y, TY (3.3V) Any Y, TY (3.3V) 80% 20% VDDQ/2 tR tF VDDQ/2 VDDQ/2 tSK1(o) tSK3(o) 500 PCBTRACE 80% 20% VDDQ/2 Any TY (2.5V) Any TY (2.5V) tR VDDQ/2 tSK2(o) PHASE ERROR AND SKEW CALCULATIONS(3,4) NOTES: 1. All inputs pulses are supplied by generators having the following characteristics: PRR 100MHz ZO = 50, tR 1.2 ns, tF 1.2 ns. 2. CL includes probe and jig capacitance. 3. The outputs are measured one at a time with one transition per measurement. 4. Phase error measurements require equal loading at outputs Y, TY, and FBOUT. CF = CL - CFBIN - CPCBtrace; CFBIN 5pF. 6 tF VDDQ/2 IDT5V2528/A 2.5 / 3.3V PHASE-LOCK LOOP CLOCK DRIVER INDUSTRIAL TEMPERATURE RANGE ORDERING INFORMATION IDT XXXXX Device Type XX Package X Process I -40C to +85C (Industrial) PG PGG Thin Shrink Small Outline Package TSSOP - Green 5V2528 5V2528A 2.5V / 3.3V Phase-Lock Loop Clock Driver CORPORATE HEADQUARTERS 2975 Stender Way Santa Clara, CA 95054 for SALES: 800-345-7015 or 408-727-6116 fax: 408-492-8674 www.idt.com 7 for Tech Support: logichelp@idt.com (408) 654-6459