HLMP-Pxxx Series, HLMP-Qxxx Series, HLMP-6xxx Series, HLMP-70xx Series Subminiature LED Lamps Data Sheet Description Features Flat Top Package Subminiature flat top package The HLMP-Pxxx Series flat top lamps use an untinted, non diffused, truncated lens to provide a wide radiation pattern that is necessary for use in backlighting applications. The flat top lamps are also ideal for use as emitters in light pipe applications. Dome Packages ---- Ideal for backlighting and light piping applications Subminiature dome package ---- Diffused dome for wide viewing angle ---- Non-diffused dome for high brightness TTL and LSTTL compatible 5V resistor lamps Available in six colors The HLMP-6xxx Series dome lamps for use as indicators use a tinted, diffused lens to provide a wide viewing angle with a high on-off contrast ratio. High brightness lamps use an untinted, nondiffused lens to provide a high luminous intensity within a narrow radiation pattern. Ideal for space limited applications Axial leads Available with lead configurations for surface mount and through hole PCB mounting Resistor Lamps The HLMP-6xxx Series 5 volt subminiature lamps with built in current limiting resistors are for use in applications where space is at a premium. Lead Configurations All of these devices are made by encapsulating LED chips on axial lead frames to form molded epoxy subminiature lamp packages. A variety of package configuration options is available. These include special surface mount lead configura tions, gull wing, yoke lead or Z-bend. Right angle lead bends at 2.54 mm (0.100 inch) and 5.08 mm (0.200 inch) center spacing are available for through hole mounting. For more information refer to Standard SMT and Through Hole Lead Bend Options for Subminiature LED Lamps data sheet. Broadcom Confidential -1- HLMP-Pxxx Series, HLMP-Qxxx Series, HLMP-6xxx Series, HLMP-70xx Series Data Sheet Device Selection Guide Part Number: HLMP-xxxx High Efficiency Red Orange Yellow High Perf. Green Emerald Green Device Description Device Outline Drawing P105 P205 P405 P305 P505 P605 Untinted, Non-diffused, Flat Top A P102 P202 P402 P302 P502 Untinted, Diffused, Flat Top A Q100 6300 Q400 6400 6500 Q600 Tinted, Diffused B Q105 6305 Q405 6405 6505 Q605 Untinted, Nondiffused, High Brightness B Q150 7000 7019 7040 Tinted, Diffused, Low Current B Nondiffused, Low Current B 6800 Tinted, Diffused, Resistor, 5V, 10 mA B 6820 Diffused, Resistor, 5V, 4 mA B Standard DH AS Red AlGaAs Red P005 6000 Q155 6600 6620 6720 Package Dimensions Flat Top Lamps Diffused and Nondiffused 0.50 (0.020) REF. 0.50 (0.020) REF. 1.40 (0.055) 1.65 (0.065) 11.68 (0.460) 10.67 (0.420) BOTH SIDES 11.68 (0.460) 10.67 (0.420) BOTH SIDES CATHODE CATHODE 0.46 (0.018) 0.56 (0.022) ANODE 0.46 (0.018) 0.56 (0.022) ANODE 1.65 (0.065) DIA. 1.91 (0.075) 0.20 (0.008) MAX. 1.65 (0.065) DIA. 1.91 (0.075) 0.25 (0.010) MAX. NOTE 2 0.20 (0.008) MAX. 2.21 (0.087) 1.96 (0.077) 1.14 (0.045) 1.40 (0.055) 0.18 (0.007) 0.23 (0.009) 0.25 (0.010) MAX. NOTE 2 2.21 (0.087) 1.96 (0.077) 0.76 (0.030) R. 0.89 (0.035) 0.94 (0.037) 1.24 (0.049) 2.03 (0.080) 1.78 (0.070) 0.63 (0.025) 0.38 (0.015) 2.44 (0.096) 1.88 (0.074) 0.18 (0.007) 0.23 (0.009) 2.92 (0.115) MAX. 0.79 (0.031) MAX. 0.79 (0.031) 0.53 (0.021) 2.08 (0.082) 2.34 (0.092) 0.63 (0.025) 0.38 (0.015) 2.08 (0.082) 2.34 (0.092) CATHODE STRIPE CATHODE STRIPE NOTES: 1. ALL DIMENSIONS ARE IN MILLIMETRES (INCHES). 2. PROTRUDING SUPPORT TAB IS CONNECTED TO CATHODE LEAD. 3. LEAD POLARITY FOR AlGaAs LAMPS IS OPPOSITE TO THE LEAD POLARITY OF SUBMINIATURE LAMPS USING OTHER TECHNOLOGIES. Broadcom Confidential -2- HLMP-Pxxx Series, HLMP-Qxxx Series, HLMP-6xxx Series, HLMP-70xx Series Data Sheet Figure 1: Proper Right Angle Mounting to a PCB to Prevent Protruding Cathode Tab from Shorting to Anode Connection CATHODE TAB NO. ANODE DOWN. YES. CATHODE DOWN. Absolute MaximumHLMP-PXXX Ratings (TA = 25C) Anode/Cathode Parameter DC Forward Current[1] Peak Forward Current[2] Standard Red DH AS AlGaAs Red High Eff. Red Orange Yellow High Perf. Green Emerald Green Unit 50 30 30 30 20 30 30 mA 1000 300 90 90 60 90 90 mA 6 6 6 V DC Forward Voltage (Resistor Lamps Only) Reverse Voltage (IR = 100 A) Transient Forward Current (10 s Pulse) 6 5 5 5 5 5 5 5 V 2000 500 500 500 500 500 500 mA -55 to +100 -40 to +100 -40 to +100 -20 to +100 Operating Temperature Range Non-Resistor Lamps Resistor Lamps -55 to +100 -40 to +85 Storage Temperature Range -55 to +100 For Thru Hole Devices: Wave Soldering Temperature [1.6 mm (0.063 in.) from body] 260C for 5 seconds For Surface Mount Devices: Reflow Soldering Temperature 260C for 20 seconds -20 to +85 C Notes: 1.See Figure 5 for current derating vs. ambient temperature. Derating is not applicable to resistor lamps. 2.Refer to Figure 6 showing Max. Tolerable Peak Current vs. Pulse Duration to establish pulsed operating conditions. 3.The transient peak current is the maximum non-recurring peak current the device can withstand without failure. Do not operate these lamps at this high current. Broadcom Confidential -3- HLMP-Pxxx Series, HLMP-Qxxx Series, HLMP-6xxx Series, HLMP-70xx Series Data Sheet Electrical/Optical Characteristics (TA = 25C) Standard Red Device HLMP- Parameter Symbol 6000-E00xx 6000-G00xx Luminous Intensity[1] IV P005-F00xx All 6000 P005 All Min. Typ. 0.63 1.2 1.60 3.2 1.0 2.5 Forward Voltage VF 1.4 1.6 Reverse Breakdown Voltage VR 5.0 12.0 90 Max. 2.0 Unit Test Conditions mcd IF = 10 mA V IF = 10 mA V IR = 100 A Included Angle Between Half Intensity Points[2] 21/2 Peak Wavelength PEAK 655 nm Dominant Wavelength[3] d 640 nm Spectral Line Half Width 1/2 24 nm Speed of Response s 15 ns Capacitance C 100 pF VF = 0; f = 1 MHz Thermal Resistance RJ-PIN 170 C/W Junction-to-Cathode Lead Luminous Efficacy[4] v 65 lm/W Broadcom Confidential -4- 125 Deg. HLMP-Pxxx Series, HLMP-Qxxx Series, HLMP-6xxx Series, HLMP-70xx Series Data Sheet DH AS AlGaAs Red Device HLMP- Min. Typ. P102-F00xx 1.0 20.0 P105-L00xx 10.0 30.0 P105-NP000 25 Q100-M00xx 16 45 25.0 45.0 Q100-N00xx Q100-PQ000 Parameter Luminous Intensity[1] Symbol IV 40 Q105-ST000 160 Q150-F00xx 1.0 1.8 Q155-F00xx 1.0 4.0 Q150/Q155 All VF Reverse Breakdown Voltage VR 5.0 P105 Q100/Q150 mcd 200 500 IF = 1 mA 1.8 2.2 1.6 1.8 15.0 V V IF = 20 mA IF = 1 mA IR = 100 A 125 Included Angle Between Half Intensity Points[2] 21/2 Q105/Q155 90 Deg. 28 Peak Wavelength All Test Conditions IF = 20 mA 125 40 Forward Voltage Unit 80 Q105-P00xx Q100 Max. PEAK 645 nm Dominant Wavelength[3] d 637 nm Spectral Line Half Width 1/2 20 nm Speed of Response s 30 ns Exponential Time Constant; e-t/ts Capacitance C 30 pF VF = 0; f = 1 MHz Thermal Resistance RJ-PIN 170 C/W Luminous Efficacy[4] v 80 lm/W Broadcom Confidential -5- Measured at Peak Junction-to-Cathode Lead HLMP-Pxxx Series, HLMP-Qxxx Series, HLMP-6xxx Series, HLMP-70xx Series Data Sheet High Efficiency Red Device HLMP- Min. Typ. P202-F00xx 1.0 5.0 P205-F00xx 1.0 8.0 6300-F00xx 1.0 10.0 6300-KL000 6305-L00xx Parameter Luminous Intensity[1] Symbol IV 6.3 Max. Unit Test Conditions IF = 10 mA 20.0 mcd 10.0 40.0 7000-D00xx 0.4 1.0 IF = 2 mA 6600-G00xx 1.6 5.0 VF = 5.0V 6620-F00xx 1.0 2.0 1.5 1.8 3.0 9.6 13.0 3.5 5.0 All 6600 5620 All Forward Voltage (Nonresistor Lamps) VF Forward Current (Resistor Lamps) IF Reverse Breakdown Voltage VR 5.0 P205 6305 IF = 10 mA mA VF = 5.0V V IR = 100 A 125 Included Angle Between Half Intensity Points[2] 21/2 All Diffused 28 Deg. 90 Peak Wavelength All 30.0 V PEAK 635 nm Dominant Wavelength[3] d 626 nm Spectral Line Half Width 1/2 40 nm Speed of Response s 90 ns Capacitance C 11 pF Thermal Resistance RJ-PIN 170 C/W Luminous Efficacy[4] v 145 lm/W Broadcom Confidential -6- Measured at Peak VF = 0; f = 1 MHz Junction-to-Cathode Lead HLMP-Pxxx Series, HLMP-Qxxx Series, HLMP-6xxx Series, HLMP-70xx Series Data Sheet Orange Device HLMP- Min. Typ. P402-F00xx 1.0 4.0 P405-F00xx 1.0 6 P405-JK000 Parameter Luminous Intensity Symbol IV 4.0 Q400-F00xx 1.0 8 Q405-H00xx 2.5 14 All P40x Q40x All Forward Voltage VF 1.5 1.9 Reverse Breakdown Voltage VR 5.0 30.0 125 Max. Unit 12.5 mcd IF = 10 mA 3.0 V IF = 10 mA V IR = 100 A Included Angle Between Half Intensity Points[2] 21/2 Peak Wavelength PEAK 600 nm Dominant Wavelength[3] d 602 nm Spectral Line Half Width 1/2 40 nm Speed of Response s 260 ns Capacitance C 4 pF Thermal Resistance RJ-PIN 170 C/W Luminous Efficacy[4] v 380 lm/W Broadcom Confidential -7- 90 Test Conditions Deg. Measured at Peak VF = 0; f = 1 MHz Junction-to-Cathode Lead HLMP-Pxxx Series, HLMP-Qxxx Series, HLMP-6xxx Series, HLMP-70xx Series Data Sheet Yellow Device HLMP- Min. Typ. P302-F00xx 1.0 3.0 P305-F00xx 1.0 4.0 6400-F00xx 1.0 9.0 6400-JK000 4.0 6405-J00xx Parameter Luminous Intensity Symbol IV 3.6 Max. 12.5 16 7019-D00xx 0.4 0.6 6720-F00xx 0.9 2.0 IF = 10 mA 50 IF = 2 mA All Forward Voltage (Nonresistor Lamps) VF 2.0 2.4 V 6720 Forward Current (Resistor Lamps) IF 3.5 5.0 mA All Reverse Breakdown Voltage VR 5.0 P305 6405 50.0 IF = 10 mA VF = 5V V 125 Included Angle Between Half Intensity Points[2] 21/2 All Diffused 28 Deg. 90 Peak Wavelength All Test Conditions mcd 20 6405-MN0xx Unit PEAK 583 nm Dominant Wavelength[3] d 585 nm Spectral Line Half Width 1/2 36 nm Speed of Response s 90 ns Capacitance C 15 pF Thermal Resistance RJ-PIN 170 C/W Luminous Efficacy[4] v 500 lm/W Broadcom Confidential -8- Measured at Peak VF = 0; f = 1 MHz Junction-to-Cathode Lead HLMP-Pxxx Series, HLMP-Qxxx Series, HLMP-6xxx Series, HLMP-70xx Series Data Sheet High Performance Green Device HLMP- Min. Typ. P502-F00xx 1.0 3.0 P505-F00xx 1.6 6.3 6500-F00xx 1.0 7.0 10.0 40.0 7040-D00xx 0.4 0.6 IF = 2 mA 6800-G00xx 1.6 5.0 VF = 5V 6820-F00xx 1.0 2.0 6505-L00xx All 6800 6820 All Parameter Luminous Intensity Symbol IV Forward Voltage (Nonresistor Lamps) VF Forward Current (Resistor Lamps) IF Reverse Breakdown Voltage VR 5.0 P505 6505 Test Conditions IF = 10 mA mcd 2.1 2.7 9.6 13.0 3.5 5.0 50.0 Unit V mA V IF = 10 mA VF = 5V IR = 100 A 125 Included Angle Between Half Intensity Points[2] 21/2 All Diffused 28 Deg. 90 Peak Wavelength All Max. PEAK 565 nm Dominant Wavelength[3] d 569 nm Spectral Line Half Width 1/2 28 nm Speed of Response s 500 ns Capacitance C 18 pF Thermal Resistance RJ-PIN 170 C/W Luminous Efficacy[4] v 595 lm/W Broadcom Confidential -9- VF = 0; f = 1 MHz Junction-to-Cathode Lead HLMP-Pxxx Series, HLMP-Qxxx Series, HLMP-6xxx Series, HLMP-70xx Series Data Sheet High Performance Green[1] Device HLMP- Parameter Symbol P605-F00xx Q600-F00xx Luminous Intensity IV Q605-F00xx All P605 Q60x All Forward Voltage VF Reverse Breakdown Voltage VR Min. Typ. 1.0 1.5 1.0 1.5 1.0 7.5 2.2 5.0 125 Max. 3.0 Unit mcd IF = 10 mA V IF = 10 mA V IR = 100 A Included Angle Between Half Intensity Points[2] 21/2 Peak Wavelength PEAK 558 nm Dominant Wavelength[3] d 560 nm Spectral Line Half Width 1/2 24 nm Speed of Response s 3100 ns Capacitance C 35 pF Thermal Resistance RJ-PIN 170 C/W Luminous Efficacy[4] v 656 lm/W 90 Deg. Note: 1. Please refer to Application Note 1061 for information comparing standard green and emerald green light output degradation. Broadcom Confidential - 10 - Test Conditions Measued at Peak VF = 0; f = 1 MHz Junction-to-Cathode Lead HLMP-Pxxx Series, HLMP-Qxxx Series, HLMP-6xxx Series, HLMP-70xx Series Data Sheet Figure 2: Relative Intensity vs. Wavelength Figure 3: Forward Current vs. Forward Voltage (Non-Resistor Lamp) Standard Red and DH AS AlGaAs Red High Efficiency Red, Orange, Yellow, High Performance Green, and Emerald Green 100 90 HIGH EFFICIENCY RED/ORANGE FORWARD CURRENT - mA 80 70 60 YELLOW 50 40 30 HIGH PERFORMANCE GREEN, EMERALD GREEN 20 10 0 0 0.5 1 1.5 2 2.5 3 3.5 FORWARD VOLTAGE - V HLMP-PXXX fig 2b Figure 4: Relative Luminous Intensity vs. Forward Current (non-resistor lamp) Standard Red, DH As AlGaAs Red Low Current Broadcom Confidential - 11 - HER, Orange, Yellow, and High Performance Green, and Emerald Green HLMP-Pxxx Series, HLMP-Qxxx Series, HLMP-6xxx Series, HLMP-70xx Series Data Sheet Figure 5: Relative Efficiency (Luminous Intensity per Unit Current) vs. Peak Current (Non-Resistor Lamps) Standard Red DH As AlGaAs Red HER, Orange, Yellow, and High Performance Green, and Emerald Green Figure 6: Maximum Forward DC Current vs. Ambient Temperature (Derating based on TJ Max. = 110C [non-resistor lamps]) Figure 7: Maximum Tolerable Peak Current vs. Pulse Duration (IDC Max. as per Max. ratings) (non-resistor lamps) Standard Red HER, Orange, Yellow, and High DH As AlGaAs Red Performance Green Broadcom Confidential - 12 - HLMP-Pxxx Series, HLMP-Qxxx Series, HLMP-6xxx Series, HLMP-70xx Series Figure 8: Resistor Lamp Forward Current vs. Forward Voltage Data Sheet Figure 9: Resistor Lamp Luminous Intensity vs. Forward Voltage Figure 10: Relative Intensity vs. Angular Displacement Broadcom Confidential - 13 - HLMP-Pxxx Series, HLMP-Qxxx Series, HLMP-6xxx Series, HLMP-70xx Series Ordering Information Data Sheet Color Bin Limits HLMx-XXXX-X X X X X Package Emerald Green Packaging Option Color Bin Selection Green Max. Iv Bin Min. Iv Bin 4 x 4 Prod. Part Number Yellow Intensity Bin Limits Bin Min. Max. Bin Min. Max. 0 Full Distribution 9 552 556 8 555 559 7 558 562 6 561 565 0 Full Distribution 6 561 565 5 564 568 4 567 571 3 570 574 2 573 577 0 Full Distribution 1 581.5 585.0 2 584.0 587.5 3 586.5 590.0 4 589.0 592.5 A 0.10 0.20 5 591.5 593.5 B 0.16 0.32 6 591.5 595.0 C 0.25 0.50 7 594.0 597.5 D 0.40 0.80 0 Full Distribution E 0.63 1.25 1 596.5 600.0 F 1.00 2.00 2 599.0 602.5 G 1.60 3.20 3 601.5 604.0 H 2.50 5.00 4 603.8 608.2 J 4.00 8.00 5 606.8 611.2 K 6.30 12.50 6 609.8 614.2 L 10.00 20.00 7 612.8 617.2 M 16.00 32.00 8 615.8 620.2 N 25.00 50.00 P 40.00 80.00 Q 63.00 125.00 R 100.00 200.00 S 160.00 320.00 T 250.00 500.00 U 400.00 800.00 V 630.00 1250.00 W 1000.00 2000.00 X 1600.00 3200.00 Y 2500.00 5000.00 Orange Broadcom Confidential - 14 - HLMP-Pxxx Series, HLMP-Qxxx Series, HLMP-6xxx Series, HLMP-70xx Series Data Sheet Mechanical Option 00 Straight Leads, Bulk Packaging, Quantity of 500 Parts 10 Right Angle Housing, Bulk Packaging, Quantity of 500 Parts 11 Gull Wing Leads, 12 mm Tape on 7 in. Dia. Reel, 1500 Parts per Reel 12 Gull Wing Lead, Bulk Packaging, Quantity of 500 Parts 14 Gull Wing Leads, 12 mm Tape on 13 in. Dia. Reel, 6000 Parts per Reel 21 Yoke Leads, 12 mm Tape on 7 in. Dia. Reel, 1500 Parts per Reel 22 Yoke Leads, Bulk Packaging, Quantity of 500 Parts 24 Yoke Leads, 12 mm Tape on 13 in. Dia. Reel, 6000 Parts per Reel 31 Z-Bend Leads, 12 mm Tape on 7 in. Dia. Reel, 1500 Parts per Reel 32 Z-Bend Leads, Bulk Packaging, Quantity of 500 Parts 34 Z-Bend Leads, 12 mm Tape on 13 in. Dia. Reel, 6000 Parts per Reel 1L 2.54 mm (0.100 inch) Center Lead Spacing, Long Leads; 10.4 mm (0.410 in.) 1S 2.54 mm (0.100 inch) Center Lead Spacing, Short Leads; 3.7 mm (0.145 in.) 2L 5.08 mm (0.200 inch) Center Lead Spacing, Long Leads; 10.4 mm (0.410 in.) 2S 5.08 mm (0.200 inch) Center Lead Spacing, Short Leads; 3.7 mm (0.145 in.) Note: All Categories are established for classification of products. Products may not be available in all categories. Please contact your local Avago representative for further clarification/information. Broadcom Confidential - 15 - For product information and a complete list of distributors, please go to our web site: www.broadcom.com. Broadcom, the pulse logo, Connecting everything, Avago Technologies, Avago, the A logo, and R2Coupler are among the trademarks of Broadcom and/or its affiliates in the United States, certain other countries and/or the EU. Broadcom Proprietary and Confidential. Copyright (c) 2017 Broadcom. All Rights Reserved. The term "Broadcom" refers to Broadcom Limited and/or its subsidiaries. Broadcom reserves the right to make changes without further notice to any products or data herein to improve reliability, function, or design. Information furnished by Broadcom is believed to be accurate and reliable. However, Broadcom does not assume any liability arising out of the application or use of this information, nor the application or use of any product or circuit described herein, neither does it convey any license under its patent rights nor the rights of others. AV02-3609EN - April 12, 2017 Option 11, 12, 21, 22, 31, 32, 1L, 1S, 2L, 2S Standard SMT and Through Hole Lead Bend Options for Subminiature LED Lamps Data Sheet Description Features Subminiature lamps (HLMX-PXXX, HLMX-QXXX, HLMP6XXX, HLMP-70XX) are available with the above standard options. Subminiature Lamps with Options 11, 12, 21, 22, 31, and 32 are suitable for surface mount applications and their leads are formed with gull wing, yoke bend and Z bend respectively. They are available in Tape and Reel (compatible to ANSI/EIA RS-481) or bulk. Options 1L, 1S, 2L, and 2S are right angle lead bends suitable for through hole applications. * Surface mount lead configurations Ordering Information To order Subminiature Lamps packaged with these standard options, include the appropriate option code along with the device catalog part number. Example: to order the HLMP-6300-F00xx with Option 11 gull wing leads in 12 mm embossed tape on 178 mm (7 inch) diameter reels, with 1500 lamps per reel; order as follows: HLMP-6300-F0011. Order quantities must be placed in reel increments only. Orders for partial reels will not be accepted. For additional information, please contact your local Avago Technologies sales office or franchised distributor for assistance. HLMX-XXXX-X X X X X Packaging Option Color Bin Selection Max. Iv Bin Min. Iv Bin 4 x 4 Prod. Part Number * Right angle lead bend for through hole mounting * Tape and reel in accordance with ANSI/EIA RS-481 specifications Selection Guide Option Code Package Configuration Package Outline Drawing 11 A, H, K, L 12 Gull Wing Leads, 12 mm Tape on 7 in. Dia. Reel, 1500 Parts per Reel[1] Gull Wing Lead, Bulk Packaging, Quantity of 500 Parts[2] Surface Mount Lead Configurations 14 Gull Wing Leads, 12 mm Tape on 13 in. Dia. Reel, 6000 Parts per Reel[1] 21 Yoke Leads, 12 mm Tape on 7 in. Dia. Reel 1500 Parts per Reel[1] 22 Yoke Leads, Bulk Packaging, Quantity of 500 Parts[2] 24 Yoke Leads, 12 mm Tape on 13 in. Dia. Reel, 6000 Parts per Reel[1] 31 Z-Bend Leads, 12 mm Tape on 7 in. Dia. Reel 1500 Parts per Reel[1] 32 34 1L Z-Bend Leads, 12 mm Tape on 13 in. Dia. Reel, 6000 Parts per Reel[1] 2.54 mm (0.100 inch) 5.08 mm (0.200 inch) 2SCenter Lead Spacing Notes: C, J, K, L Z-Bend Leads, Bulk Packaging, Quantity of 500 Parts[2] 1SCenter Lead Spacing 2L B, I, K, L Long Leads; 10.4 mm (0.410 in.) Right Angle Lead Bends for Short Leads; 3.7 mm (0.145 in.) Through Hole Long Leads; 9.2 mm (0.364 in.)Mounting D Short Leads; 3.7 mm (0.145 in.) G E F 1. SMT lamps are supplied in 12 mm embossed carrier tape. Minimum order is for one full reel, either 7 inch or 13 inch. All other order quantities must be in reel increments only. Orders for partial reels are not accepted. 2. Vapor barrier bags are used for bulk packaging. Package Dimensions, Lead Bend Options (A) Gull Wing Lead, Option 11, 12, and 14 CATHODE ANODE 3.81 (0.150) MAX. 0.13 (0.005) R TYP. 0.79 (0.031) 0.53 (0.021) 0.13 (0.005) MAX. CATHODE STRIPE ALL DIMENSIONS ARE IN MILLIMETERS (INCHES) (B) "Yoke" Lead, Options 21, 22, and 24 CATHODE STRIPE Pkg A) Lamp - Gull Wing Lead 3.45 (0.136) NOM. 0.13 (0.005) TYP. 0.33 (0.013) R. TYP. 1.07 (0.042) TYP. 0.79 (0.031) 0.53 (0.021) 7.62 (0.300) MAX. CATHODE ANODE ALL DIMENSIONS ARE IN MILLIMETERS (INCHES) (C) Z-Bend Lead, Option 31, 32, and 34 CATHODE STRIPE 4.06 (0.160) 4.57 (0.180) 0.79 (0.031) 0.53 (0.021) 0.76 (0.030) 0.51 (0.020) 3.05 (0.120) NOM. 5.59 (0.220) 6.10 (0.240) CATHODE ALL DIMENSIONS ARE IN MILLIMETERS (INCHES) ANODE (D) Rt. Angle Bend Option 1L Pkg C) Lamp - Z-Bend 10.16 (0.400) 10.67 (0.420) 2.54 (0.100) NOM. CATHODE STRIPE ALL DIMENSIONS ARE IN MILLIMETERS (INCHES) (E) Rt. Angle Bend Option 1S 3.43 (0.135) 3.94 (0.155) 2.54 (0.100) NOM. CATHODE STRIPE ALL DIMENSIONS ARE IN MILLIMETERS (INCHES) Pkg E) Lamp - Rt Angle 1S (F) Rt. Angle Bend Option 2L 9.50 (0.374) 8.92 (0.351) 5.08 (0.200) NOM. CATHODE STRIPE ALL DIMENSIONS ARE IN MILLIMETERS (INCHES) (G) Rt. Angle Bend Option 2S Pkg F) Lamp - Rt Angle 2L 3.43 (0.135) 3.94 (0.155) 5.08 (0.200) NOM. CATHODE STRIPE ALL DIMENSIONS ARE IN MILLIMETERS (INCHES) Package Dimensions: Surface Mount Tape and Reel Options (H) 12 mm Tape and Reel, Gull Wing Lead PUSH PIN HOLE, GULL WING LEAD, DOME ONLY NOTES: 1. EMPTY COMPONENT POCKETS SEALED WITH TOP COVER TAPE. 2. MINIMUM LEADER LENGTH AT EITHER END OF THE TAPE IS 500 mm. 3. THE MAXIMUM NUMBER OF CONSECUTIVE MISSING LAMPS IS TWO. 4. IN ACCORDANCE WITH ANSI/EIA RS-481 SPECIFICATIONS, THE CATHODE IS ORIENTED TOWARDS THE TAPE SPROCKET HOLE. (I) 12 mm Tape and Reel, "Yoke" Lead NOTES: 1. EMPTY COMPONENT POCKETS SEALED WITH TOP COVER TAPE. 2. MINIMUM LEADER LENGTH AT EITHER END OF THE TAPE IS 500 mm. 3. THE MAXIMUM NUMBER OF CONSECUTIVE MISSING LAMPS IS TWO. 4. IN ACCORDANCE WITH ANSI/EIA RS-481 SPECIFICATIONS, THE CATHODE IS ORIENTED TOWARDS THE TAPE SPROCKET HOLE. (J) 12 mm Tape and Reel, Z-Bend Lead Reel DimensionsAll Dimensions Per ANSI/EIA Are in Millimeters Standard RS-481.(Inches). 7 inch Reel13 Inch Reel A C N T 178.0 2.0 (7.0 0.08) Dia. 13.0 (0.512) Dia. Typ. 50.0 (1.97) Min. 18.4 (0.72) mMax. 330 (12.9) Dia. Max. 13.0 (0.512) Dia. Typ. 100.0 (3.93) Min. 18.4 (0.72) Max. Embossed Carrier All Dimensions Tape Dimensions Are in Millimeters Per ANSI/EIA (Inches). Standard RS-481. Yoke and Gull Wing DomeGull Wing Flat Top Yoke Dome Z-Bend Dome Z-Bend Flat Top D 1.55 (0.061 0.002) Dia. 1.55 (0.061 0.002) Dia. 1.55 (0.061 0.002) Dia. (0.059 + 0.004) Dia. D1 1.0 (0.039) Dia. Min. N/A (No Push Pin Hole) N/A (No Push Pin Hole) D2 20.2 (0.795) Dia. Min. 20.2 (0.795) Dia. Min. 20.2 (0.795) Dia. Min. E 1.75 0.1 (0.069) 1.75 0.1 (0.069) 1.75 0.1 (0.069) F 5.50 0.05 (0.217 0.002) K0 3.05 0.1 (0.120) Typ. 2.54 0.1 (0.100) Typ. 3.05 0.1 (0.120) Typ. P 4.0 (0.157) Typ. 4.0 (0.157) Typ. 4.0 (0.157) Typ. P0 4.0 (0.157) Typ. 4.0 (0.157) Typ. 4.0 (0.157) Typ. P2 2.0 (0.079 0.002) 2.0 (0.079 0.002) 2.0 (0.079 0.002) t 0.3 (0.012) Typ. 0.3 (0.012) Typ. 0.3 (0.012) Typ. W 12.0 0.3 (0.472 0.012) 12.0 0.3 (0.472 0.012) 12.0 0.3 (0.472 0.012) 1.50 + 0.10 (0.059 + 0.004) Dia. 1.50 + 0.25 (0.059 + 0.010) 20.2 (0.795) Dia. Min. 1.75 0.1 (0.069) 2.97 0.1 (0.117) Typ. 4.0 (0.157) Typ. 4.0 (0.157) Typ. 2.0 (0.079 0.002) 0.305 0.013 (0.0120 0.0005) 12.0 0.3 (0.472 0.012) 1.50 + 0.10 N/A (No Push Pin Hole) 20.2 (0.795) Dia. Min. 1.75 0.1 (0.069) 3.05 0.1 (0.120) Typ. 4.0 (0.157) Typ. 4.0 (0.157) Typ. 2.0 (0.079 0.002) 0.305 0.013 (0.0120 0.0005) 12.0 0.3 (0.472 0.012) (K) 12 mm Tape and Reel PART: LOT NO: Storage Condition: 5 to 30C @ 60% RH max. CUST PART: QTY: D/C: TAPE DATE: Baking is required under the following conditions: a) Humidity Indicator Card is >10% when read at 23 5C. b) The pack has been opened for more than 1 week. Baking recommended condition: 60 5C for 20 hours. 10 CAT: BIN: QA INSP. C/O: (L) Recommended Reflow Soldering Profile and Soldering Pad Pattern for SMT Options 10 - 30 SEC. 255 - 260 C 3 C/SEC. MAX. +5 230 -0 C MAX. 3C/SEC. MAX. TEMPERATURE TEMPERATURE 10 SEC. MAX. 183C 125-170C 3-4C/SEC. 2-3C/SEC. 6 C/SEC. MAX. 150 C 3 C/SEC. MAX. 50C 60-150 SEC. 120 SEC. MAX. 217 C 200 C 100 SEC. MAX. 60 - 120 SEC. 25C TIME TIME (Acc. to J-STD-020C) Recommended SnPb reflow soldering profile. Wait until device has cooled to room temperature before handling. 0.89 (0.035) Recommended Pb-free reflow soldering profile. 0.45 (0.018) 0.89 (0.035) 1.78 (0.070) 0.45 (0.018) 3.58 (0.140) Recommended soldering pad pattern for gull wing leads 11, 12, and 14. #27 DRILL 3.73 (0.147) DIA. CLEARANCE HOLE THROUGH PC BOARD #27 DRILL 3.73 (0.147) DIA. CLEARANCE HOLE THROUGH PC BOARD 1.27 (0.50) 0.45 (0.018) 1.27 (0.50) 0.89 (0.035) 0.64 (0.025) 3.30 (0.130) 6.60 (0.260) 0.89 (0.035) 0.45 (0.018) 3.30 (0.130) DIMENSIONS ARE IN MILLIMETERS (INCHES) Recommended soldering pad pattern for yoke leads 21, 22, and 24. For product information and a complete list of distributors, please go to our website: DIMENSIONS ARE IN MILLIMETERS (INCHES) 6.60 (0.260) Recommended soldering pad pattern for Z-bend leads 31, 32, and 34. www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright (c) 2005-2008 Avago Technologies. All rights reserved. Obsoletes 5989-1206EN AV02-0069EN - September 2, 2008