COMPUTING Data Sheet MVME7100 NXP MPC864xD VME SBC (R) The MVME7100 adds performance and features while protecting the fundamental investment in VMEbus and related technologies The Artesyn Embedded Technologies MVME7100, featuring the system-on-chip MPC864xD processor, offers a growth path for VMEbus customers with applications on the previous generation of VME, specifically the MPC74xx processors. The system-on-chip implementation offers power/thermal, reliability, and lifecycle advantages not typically found in alternative architectures. Up to 1.3GHz system-on-chip NXP MPC864xD with dual PowerPC(R) e600 processor cores, dual integrated memory controllers, DMA engine, PCI Express interface, Ethernet, and local I/O The Artesyn MVME7100 single-board computer (SBC) helps OEMs of industrial, medical, and defense/aerospace equipment add performance and features for competitive advantage while still protecting the fundamental investment in VMEbus and related technologies. Customers can keep their VMEbus infrastructure (chassis, backplanes, and other VMEbus and PMC boards) while improving performance and extending the lifecycle. Also, the extended lifecycle of Artesyn computing products helps reduce churns in development and support efforts resulting from frequent product changes. Extended temperature (-40 C to +71 C) and rugged board variants available Four Gigabit Ethernet ports Up to 2GB of DDR2 ECC memory, 128MB NOR flash and 2GB, 4GB or 8GB NAND flash USB 2.0 controller for integrating cost-effective peripherals (commercial temperature only) 2eSST VMEbus protocol with 20MB/s transfer rate across the VMEbus Board support packages for VxWorks, LynxOS, and Linux Dual 33/66/100 MHz PMC-X sites for expansion via industry standard modules with support for processor PMCs 8x PCI Express expansion connector for PMC-X and XMC expansion using Artesyn XMCspan MVME7216E direct-connect rear transition module (RTM) for I/O routing through rear of a VMEbus chassis The faster processor and 2eSST VMEbus interface combine to offer significant performance improvement. New cost-effective peripherals can be integrated easily using USB interfaces. Extended temperature (-40 C to +71 C) variants support a wide range of operating and storage temperatures in addition to increased tolerances for shock. This enables the boards to operate in harsh environments while maintaining structural and operational integrity. MVME7100 Data Sheet MVME7100 Block Diagram ABT/RST USB* GbE RJ-45 PMC1 Front I/O GbE RJ-45 PMC2 Front I/O COM Front Panel PHY 5482 Up to 2GB DDR2 Memory XCVR RS-232 Serial Port 0 GbE 1 GbE 2 GbE 3 GbE 4 User 128 KB DDR2 MC DUART TSEC1 TSEC2 MPC864xD Processor TSEC3 PCI Express Device Bus PCI Express Serial Ports 1-4 XMCspan PHY 5482 E2P PEX8112 USB* PD720101 E2P TSi384 PMC 1 QUART 16C554 GbE 4 CPLD Decode Timers/Regs Flash 128MB Temp MAX6649 Flash 2, 4 or 8GB MRAM 512KB PCI Express Switch E2P TSi384 E2P TSi384 VME TSi148 XCVR 22501 PMC 2 VME Bus XCVR RS-232 GbE 3 VPD 8 KB I2C Bus I2C Bus LBC TSEC4 RTC DS1375 COM2 - COM5 PMC 1 Jn4 IO P2 I2C Bus P1 * Commercial temperature only Overview VMEbus 2eSST Performance The 2eSST protocol offers an available VME bus bandwidth of up to 320MB/s, an increase of up to 8x over VME64, while maintaining backward compatibility with VME64 and VME32. The combination of the latest Texas Instruments VMEbus transceivers and the Tundra Tsi148 VMEbus bridge's legacy protocol support allows customers to integrate the MVME7100 series into their existing infrastructure providing backward compatibility and thereby preserving their investment in existing VMEbus boards, backplanes, chassis and software. Balanced Performance The MVME7100 series provides more than just faster VMEbus transfer rates; it provides balanced performance from the processor, memory subsystem, local busses and I/O subsystems. This coupled with a wealth of I/O interfaces make the MVME7100 series ideal for use as an application-specific compute blade, or an intelligent I/O blade/carrier. The NXP MPC864xD system-onchip (SoC) processor, running at speeds up to 1.3GHz, is well-suited for I/O and data-intensive applications. The integrated SoC design creates an I/O intensive state-of-the-art package that combines dual low power processing cores with on-chip L2 cache and dual integrated DDR2 memory controllers, PCI Express, DMA , Ethernet and local device I/O. The on-chip PCI Express interface and dual DDR2 memory busses are well matched to the processor. To ensure optimal I/O performance, the 8x PCI Express port is connected to a five-port PCI Express switch. Three 4x PCI Express ports are connected to PCI Express-to-PCI-X bridges which provide independent PCI-X busses for the two PMC-X sites and VME bus interface. A 1x PCI Express port is connected to a PCI Express-toPCI bridge which is connected to the USB chip (commercial temperature only). The MVME7100 also offers quad Gigabit Ethernet interfaces, USB 2.0, and five (5) RS-232 serial connections. All of this adds up to a set of well-balanced, high-performance subsystems offering unparalleled performance. MVME7100 Data Sheet Backward Compatibility Specifications The MVME7100 series continues the direction of providing a migration path from Artesyn's embedded controllers such as the MVME16x, MVME17x, MVME2300/MVME2400, and from Artesyn SBCs such as the MVME2600/2700 to a single platform. The MVME7100 series, like the MVME3100, MVME5100, MVME5500, and MVME6100 series, merged the best features of Artesyn's embedded controllers and SBCs enabling OEMs to support varying I/O requirements with the same base platform, simplifying part number maintenance, technical expertise requirements, and sparing. Processor The MVME7100 series offers customers an alternate migration path from the MVME2100, MVME2300, MVME2400, MVME2600, MVME2700, MVME3100, MVME5100, MVME5500 and MVME6100 boards to allow them to take advantage of features such as the integrated MPC864xD SoC processor, DDR2 memory, Gigabit Ethernet, PCI-X, PCI Express, USB, and 2eSST. Main Memory PCI Expansion The MVME7100 has an 8x PCI Express connection to support PCI Express expansion carriers such as the Artesyn XMCspan. Flash Memory Transition Modules The MVME7216E transition module provides industry standard connector access to two 10/100/1000BaseTX ports, and four asynchronous serial ports configured as RS-232 DTE. All of these are via RJ-45 connectors. The MVME7216E RTM is designed to directly connect to the VME backplane in chassis' with an 80 mm deep rear-transition area. Software Support Firmware Monitor The MVME7100 firmware (known as MOTLoad) is resident in the MVME7100 flash and provides power-on self-test, initialization and operating system booting capabilities. In addition, it provides a debugger interface similar to the time proven "BUG" interface on previous VMEbus boards from Artesyn. Operating Systems and Kernels The MVME7100 series supports booting a variety of operating systems including a complete range of real-time operating systems and kernels. Artesyn Embedded Technologies Embedded Computing Linux (2.6.25 kernel) is available now. VxWorks BSPs (5.5.1 AMP, 6.8 SMP) are provided and supported by Wind River Systems. * Microprocessor: NXP MPC864xD with dual PowerPC e600 cores * Clock Frequency: 1.06 or 1.3 GHz * On-chip L1 Cache (I/D): 32 K/32 K per core * On-chip L2 Cache: 1MB per core System Controller Integrated within MPC864xD Type: Double data rate (DDR2) SDRAM Speed: DDR2-533 Capacity: 1GB or 2GB Configuration: Dual memory controller Type: NOR flash, on-board programmable * Capacity: 128MB * Write Protection: Hardware via switch, software via register or sector lock Type: NAND flash, on-board programmable * Capacity: 2GB, 4GB or 8GB * Write Protection: Software via register * Supported by YAFFS (Linux) or Datalight FlashFX(R) Pro (VxWorks) under separate license Non-volatile Memory Type: SEEPROM, on-board programmable * Capacity: 128 KB (available for users), 8 KB baseboard Vital Product Data (VPD), and two (2) 256B Serial Presence Detect (SPD) Type: MRAM * Capacity: 512 KB VMEbus Interface Compliance: ANSI/VITA 1-1994 VME64 (IEEE STD 1014), ANSI/ VITA 1.1-1997 VME64 Extensions, VITA 1.5-199x 2eSST Controller: Tundra Tsi148 PCI-X to VMEbus bridge with support for VME64 and 2eSST protocols DTB Master: A16, A24, A32, A64; D08-D64, SCT, BLT, MBLT, 2eVME, 2eSST DTB Slave: A16, A24, A32, A64; D08-D64, SCT, BLT, MBLT, 2eVME, 2eSST, UAT Arbiter: RR/PRI Interrupt Handler/Generator: IRQ 1-7/Any one of seven IRQs System Controller: Yes, switchable or auto detect Location Monitor: Two, LMA32 MVME7100 Data Sheet Ethernet Interface Counters/Timers Controller: MPC864xD Triple Speed (TSEC) Ethernet Controllers TOD Clock Device: Maxim DS1375 I2C device with battery backup Interface Speed: Four @ 10/100/1000Mbps (TSEC) Cell Storage Life: 10 years at 25 C Connector: Two Gigabit Ethernet ports routed to front panel RJ-45, two Gigabit Ethernet ports to VMEbus P2 connector, pin out matching MVME7216E RTM Cell Capacity Life: One year at 100% duty cycle, 25 C Indicators: Link status/speed/activity Asynchronous Serial Ports Port 1 Removable Battery: Yes Real-Time Timers/Counters: Four, 32-bit programmable timers in PLD; four, 32-bit programmable/ cascadable timers in MPC864xD Watchdog Timer: In PLD * Controller: MPC864xD Duart (second port N/C) Board Size and Weight * Number of Ports: One 16550 compatible Height: 233.4 mm (9.2 in.) * Configuration: RS-232 DTE (RxD, TxD, RTS, CTS) Depth: 160.0 mm (6.3 in.) * Async Baud Rate, bps max.: 38.4 K RS-232, 115 Kbps raw Connector: One front panel Mini DB-9 Front Panel Height: 261.8 mm (10.3 in.) * * Mini DB-9 to DB-9 adapter cable: SERIAL-MINI-D2 Ports 2-5 Width: 19.8 mm (0.8 in.) Max. Component Height: 14.8 mm (0.58 in.) Weight: .68 kg (1.5 lbs.) * Controller: Exar ST16C544D Quart * Number of Ports: Four 16550 compatible * Configuration: RS-232 (RxD, TxD, RTS, CTS) Board Variant Power (+5 V 5%) * Async Baud Rate, b/s max: 38.4 K RS-232, 115 Kbps raw MVME7100-0161 * Connector: Via VMEbus P2 connector, pinout matching MVME7216E RTM Typical: 40 W Maximum: 55 W MVME7100-0163 Typical: 40 W Maximum: 55 W MVME7100-0171-2GF Typical: 45 W Maximum: 60 W MVME7100-0173-2GF Typical: 45 W Maximum: 60 W USB Interface (commercial temperature only) * Controller: NEC 720101 * Configuration: USB 2.0 * Number of ports: One * Connector: One powered port routed to front panel Dual IEEE P1386.1 PCI Mezzanine Card Slots Address/Data: A32/D32/D64, PMC PN1, PN2, PN3, PN4 connectors (PN4 for PMC1 only) PCI Bus Clock: 33 MHz, 66 MHz or 100 MHz PCI/ PCI-X Signaling: 3.3 V Power: +3.3 V, +5 V, 12 V Module Types: Two single-wide or one doublewide, front panel or P2 I/O, PMC and PrPMC support, PMC1 site Pn4 routed to VMEbus P2 connector rows A and C PCI Expansion Connector for interface to XMCSPAN boards 8x PCI Express interface One 76-pin connector located on MVME7100 planar Power Requirements Estimated MTBF Expected field MTBF estimate based on Telcordia SR-332, issue 1, ground fixed, controlled environment, unit ambient air temperature of 40 C is 1,066,000 hours at 60% confidence level. Contact Artesyn for alternative environments or temperatures. MVME7100 Data Sheet Other Features All Modules RoHS compliant Environmental Jumper-less configuration Commercial -ET On-board temperature sensor (Maxim MAX6649) Cooling Method Forced Air Forced Air JTAG header for connection of diagnostic tools Operating Temperature 0 C to +55 C -40 C to +71 C Front Panel Storage Temperature -40 C to +85 C -50 C to +100 C IEEE or Scanbe handles Vibration Sine 1G, 5 - 200 Hz 1G, 15 - 2000 Hz* Connectors for serial, Gigabit Ethernet and USB ports (commercial temperature only) Vibration Random N/A .0007g2/Hz 15 - 2000 Hz* Openings for PMC sites Shock N/A 4 g/11 mS* Humidity 5% to 90% RH to 100% RH Conformal Coating Optional Optional Transition Modules I/O Connectors MVME7216E * Asynchronous Serial Ports: Four, RJ-45, labeled as COM2-5 * Ethernet: Two 10/100/1000BaseTX, RJ-45 Non-Volatile Storage 8 KB VPD SEEPROM Board Size Height: 233.4 mm (9.2 in.) Depth: 80.0 mm (3.1 in.) Front Panel Height: 261.8 mm (10.3 in.) Front Panel Width: 19.8 mm (0.8 in.) *Final ET shock and vibration capabilities TBD. Values shown are minimums. Safety All printed wiring boards (PWBs) are manufactured with a flammability rating of 94V-0 by UL recognized manufacturers Electromagnetic Compatibility (EMC) Intended for use in systems meeting the following regulations: * U.S.: FCC Part 15, Subpart B, Class A (non-residential) * Canada: ICES-003, Class A (non-residential) Artesyn board products are tested in a representative system to the following standards: * CE Mark per European EMC Directive 89/336/EEC with Amendments; Emissions: EN55022 Class B; Immunity: EN55024 MVME7100 Data Sheet Ordering Information Part Number Description Weight MVME7100-0161 1.06 GHz MPC8640D, 1GB DDR2 memory, 4GB NAND flash, SCANBE (ENP1) 0.57 kg MVME7100-0163 1.06 GHz MPC8640D, 1GB DDR2 memory, 4GB NAND flash, IEEE (ENP1) 0.61 kg MVME7100-0171-2GF 1.3 GHz MPC8641D, 2GB DDR2 memory, 2GB NAND flash, SCANBE (ENP1) 0.57 kg MVME7100-0173-2GF 1.3 GHz MPC8641D, 2GB DDR2 memory, 2GB NAND flash, IEEE (ENP1) 0.62 kg MVME7100ET-0161-2GF Extended temperature - 1.06 GHz MPC8640D, 1GB DDR2 memory, 2GB NAND flash, SCANBE (ENP2) 0.60 kg Related Products XMCSPAN-001 XMC Expansion, IEEE handles MVME7216E-101 Rear transition module MVME721ET-101 Extended temp RTM, new NEW I/O on 5 row P2, two GbE, four serial, PIM, 6E (for use with MVME3100/4100/7100) MVME721ET-102 Extended temp RTM SCANBE, I/O on 5 row P2, two GbE, four serial, PIM, 6E (for use with MVME3100/4100/7100) SERIAL-MINI-D2 Serial cable - Micro D sub connector to standard DB-9 ACC/CABLE/SER/DTE/6E Serial cable, RD 009, 2M, 2 DTE MD/D, RJ-45 to DB-9 Solution Services Artesyn Embedded Technologies provides a portfolio of solution services optimized to meet your needs throughout the product lifecycle. Design services help speed time-to-market. Deployment services include global 24x7 technical support. Renewal services enable product longevity and technology refresh. WORLDWIDE OFFICES United States Hong Kong +1 888 412 7832 +852 2176 3540 China Korea +86 400 8888 183 +82 2 6004 3268 Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. NXP and QorIQ are trademarks of NXP B.V. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. Specifications are subject to change without notice. (c) 2018 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions, please visit www.artesyn.com/legal. www.artesyn.com MVME7100-DS 10Dec2018