Only One Name Means ProTek’Tion™
The PP-SM Series are thyristor surge suppression (TSS) devices designed to protect telecommunicaon equipment
against lightning and transients induced by AC power lines. These devices can be used on central oce equipment,
PBX, DSU, OCU and other telecommunicaon equiment/systems. The bidireconal conguraon provides protecon
for both posive and negave transients and the discrete surface mount package allows for individual placement of
the device on line cards or other locaons where mulple component devices do not oer the versale in board trace
layout.
This series can be used to provide protecon in accordance with industry standards such as FCC Part 68, ANSI C62.41,
UL 1459, GR-1089-CORE, IEC 61000-2, IEC 61000-4 and IEC 61000-4-5 requirements.
• IEC Compability IEC 61000-4-2 (ESD): Air 15kV, Contact 8kV
• IEC Compability IEC 61000-4-4 (EFT): 40A, 5/50ns
• IEC Compability 61000-4-5 (Surge): 95A, 8/20µs - L4(Line-Ground),
48A - L4(Line-Line) & 83A - L2(Power)
• FCC Part 68, UL 1459, Bellcore 1089 & ITU-K.20/K.21 Compliant
• UL File Recognion #E208219
• Peak O-State Voltage from 25 to 300 Volts
• Surge Current Capability (See Table 1)
• ESD Protecon > 25 kilovolts
• Low Capacitance for T1/E1 Trunk & Line Card Applicaons
• Bidireconal Conguraon
• RoHS Compliant
• REACH Compliant
• Molded Plasc DO-214AA Package
• Approximate Weight: 2.5 grams
• Lead-Free Pure-Tin Plang (Annealed)
• Solder Reow Temperature:
Pure-Tin - Sn, 100: 260-270°C
• Flammability Rang UL 94V-0
• 12mm Tape and Reel per EIA Standard 481
• T1/E1 Trunk & Line Cards
• SLIC Line Card
• DBX Branch Exchange Switches
• FCC Part 68 Customer Premise Equipment
• Line Interface Modem
• xDSL Architecture Interface
SA 150 150 100 50 50 20 500 2000
SB 300 300 150 100 80 32 500 2000
SC 500 400 200 200 100 60 500 2000
1. Crical rate of rise for On-State Current (di/dt) and O-State Voltage (dv/dt).
DEVICE SYMBOL
BIDIRECTIONAL
Only One Name Means ProTek’Tion™
Surge Current - 50/60Hz (SC Series) ITSM 60 Amps
Juncon Temperature TA-40 to 150 °C
Storage Temperature TSTG -55 to 150 °C
Thermal Resistance (Juncon) - SA & SB Series RQJC 28 °C/Wa
Thermal Resistance (Juncon) - SC Series RQJC 26 °C/Wa
Thermal Resistance (Ambient) - SA & SB Series RQJA 90 °C/Wa
Thermal Resistance (Ambient) - SC Series RQJA 85 °C/Wa
tf
Peak Value IPP
TEST
WAVEFORM
PARAMETERS
tf = 10µs
td = 1000µs
td = t/(IPP/2)
e-t
IPP
ITSM
IT
IS
IH
IDRM
VTVDRM
VS
PPxxxxSA
PPxxxxSC
PPxxxxSB
Only One Name Means ProTek’Tion™
PP0640SA GC 58 77 150 800 5 4 2.2 60
PP0720SA GD 65 88 150 800 5 4 2.2 60
PP0800SA GE 75 98 150 800 5 4 2.2 60
PP1100SA GF 90 130 150 800 5 4 2.2 60
PP1300SA GG 120 160 150 800 5 4 2.2 40
PP1500SA GH 140 180 150 800 5 4 2.2 40
PP1800SA GI 160 220 150 800 5 4 2.2 40
PP2300SA GJ 190 260 150 800 5 4 2.2 30
PP2600SA GK 220 300 150 800 5 4 2.2 30
PP3100SA GL 275 350 150 800 5 4 2.2 30
PP3500SA GM 300 400 150 800 5 4 2.2 30
PP0300SB GN 25 40 50 800 5 4 2.2 110
PP0640SB GP 58 77 150 800 5 4 2.2 60
PP0720SB GQ 65 88 150 800 5 4 2.2 60
PP0800SB GR 75 98 150 800 5 4 2.2 60
PP1100SB GS 90 130 150 800 5 4 2.2 60
PP1300SB GT 120 160 150 800 5 4 2.2 40
PP1500SB GU 140 180 150 800 5 4 2.2 40
PP1800SB GV 160 220 150 800 5 4 2.2 40
PP2300SB GW 190 260 150 800 5 4 2.2 30
PP2600SB GX 220 300 150 800 5 4 2.2 30
PP3100SB GY 275 350 150 800 5 4 2.2 30
PP3500SB GZ 300 400 150 800 5 4 2.2 30
PP0640SC HC 58 77 150 800 5 4 2.2 120
PP0720SC HD 65 88 150 800 5 4 2.2 120
PP0800SC HE 75 98 150 800 5 4 2.2 120
PP1100SC HF 90 130 150 800 5 4 2.2 120
PP1300SC HG 120 160 150 800 5 4 2.2 80
PP1500SC HH 140 180 150 800 5 4 2.2 80
PP1800SC HI 160 220 150 800 5 4 2.2 80
PP2300SC HJ 190 260 150 800 5 4 2.2 60
PP2600SC HK 220 300 150 800 5 4 2.2 60
PP3100SC HL 275 350 150 800 5 4 2.2 60
PP3500SC HM 300 400 150 800 5 4 2.2 60
1. Capacitance imblance between posive and negave polaries is typically < 15pF.
Only One Name Means ProTek’Tion™
Only One Name Means ProTek’Tion™
The TSS (Thyristor Surge Suppressor) device is located across the p-to-ring aer a liming resistor and fuse combinaon. RTIP and RRING resistors are oponal de-
pending upon the TSS device selecon. Without the resistors, the PP3100SB/SC is recommended. However, with a resistance value of 7.5 Ohms for p and ring, the
PP3100SA is recommended. Digital signals may use a lower TSS device depending upon the total p to ring voltage range. Selecon of the TSS device, either PPxxxx-
SA or SB/SC is based upon the value of the p and ring resistors. For the Naonal Electric Code (NEC) arcle 800, it is recommended that at least one fuse be used in
the p or ring line for metallic surges. Fuses may be replaced with a suitable Posive Temperature Coecient (PTC) automac reseable current liming device.
To Protected
Equipment
TIP
RING
RTip
RRing
Fuse
There are two TSS devices, one located from p-to-ground and one ring-to-ground. For standard analog signals, the PP3100SA is recommended with a typical resistor
value for p and ring of 15 Ohms. The PP3100SB/SC is recommended for resistor values of 7.5 Ohms each. The Naonal Electric Code (NEC) arcle 800 requires two
fuse elements when connecng to ground. Fuses or a suitable Posive Temperature Coecient (PTC) automac reseable current liming device may be used. The
purpose of this circuit is to limit AC power current from geng on the ground line causing any safety hazard.
To Protected
Equipment
TIP
RING
RTip
RRing
Only One Name Means ProTek’Tion™
Three equal TSS devices are used in this applicaon for metallic (p-to-ring) and longitudinal (p-to-ground and ring-to-ground) protecon. For analog signals, the
PP3100SB/SC is recommended. With a resistance value of 15 Ohms for the p and ring resistors, the PP3100SA may be used. The Naonal Electric Code (NEC) arcle
800 requires two fuse elements when connecng to ground. Fuses or a suitable Posive Temperature Coecient (PTC) automac reseable current liming device
may be used. This circuit is recommended for protecon against the Bellcore requirement: First Level Lightning Surge Tests (Telecommunicaons Port), document #
GR-1089-CORE.
To Protected
Equipment
TIP
RING
RTip
RRing
Circuit board layout is crical for electromagnec compability protecon. The following guidelines are recommended:
• The protecon device should be placed near the input terminals or connectors, the device will divert the transient current
immediately before it can be coupled into the nearby traces.
• The path length between the TVS device and the protected line should be minimized.
• All conducve loops including power and ground loops should be minimized.
• The transient current return path to ground should be kept as short as possible to reduce parasic inductance.
• Ground planes should be used whenever possible. For mullayer PCBs, use ground vias.
Only One Name Means ProTek’Tion™
A 1.96 2.21 0.077 0.087
B 4.06 4.57 0.160 0.180
C 3.30 3.94 0.130 0.155
D 2.00 2.50 0.079 0.098
E 0.76 1.52 0.030 0.060
F 0.10 0.20 0.004 0.008
G 5.08 5.59 0.200 0.220
H 0.15 031 0.006 0.012
1. Dimensions are exclusive of mold ash and metal burrs.
A 2.10 - 0.083 -
B 1.27 - 0.050 -
C - 2.69 - 0.106
D 1.27 - 0.083 -
A C
B
Polarity Band
D
G
F
E
H
A
B C D
Only One Name Means ProTek’Tion™
PPxxxxSA/SB/SC -LF -T13 3,000 13” n/a
User Direcon of Feed
t
K0
A0 P
D
P0
E
B0
F
W
10 Pitches Cumulave
Tolerance on tape ± 0.2
330mm (13”) 12mm 3.79 ± 0.15 5.72 ± 0.15 2.46 ± 0.30 1.55 ± 0.05 1.75 ± 0.10 5.5 ± 0.05 12.00 ± 0.30 4.00 ± 0.10 8.00 ± 0.10 0.25 ± 0.10
1. Dimensions are in millimeters.
2. Surface mount product is taped and reeled in accordance with EIA-481.
3. Sux - T13 = 13” Reel - 3,000 pieces per 12mm tape.
4. Marking on Part - marking code (see page 2) and logo.
Package outline, pad layout and tape specicaons per document number 06013.R5 2/11
Only One Name Means ProTek’Tion™
ProTek Devices, based in Tempe, Arizona USA, is a manufacturer of Transient Voltage Suppression (TVS) products designed specically for
the protecon of electronic systems from the eects of lightning, Electrostac Discharge (ESD), Nuclear Electromagnec Pulse (NEMP), in-
ducve switching and EMI/RFI. With over 25 years of engineering and manufacturing experience, ProTek designs TVS devices that provide
applicaon specic protecon soluons for all electronic equipment/systems.
ProTek Devices Analog Products Division, also manufactures analog interface, control, RF and power management products.
COPYRIGHT © ProTek Devices 2000 - This literature is subject to all applicable copyright laws and is not for resale in any manner.
SPECIFICATIONS: ProTek reserves the right to change the electrical and or mechanical characteriscs described herein without noce.
DESIGN CHANGES: ProTek reserves the right to disconnue product lines without noce and that the nal judgement concerning selecon and specicaons is the buyer’s and that in furnishing engineering
and technical assistance. ProTek assumes no responsibility with respect to the selecon or specicaons of such products. ProTek makes no warranty, representaon or guarantee regarding the suitability of
its products for any parcular purpose, nor does ProTek assume any liability arising out of the applicaon or use of any product or circuit and specically disclaims any and all liability without limitaon special,
consequenal or incidental damages.
LIFE SUPPORT POLICY: ProTek Devices products are not authorized for use in life support systems without wrien consent from the factory.
2929 South Fair Lane
Tempe, Arizona 85282
USA
General: 602-431-8101
Sales: 602-414-5109
Customer Service: 602-414-5114
General: 602-431-2288
Sales: sales@protekdevices.com
Customer Service: service@protekdevices.com
Technical Support: support@protekdevices.com
www.protekdevices.com
www.protekanalog.com
