W567B030 - Nuvoton Technology Corp. America

W567BXXX Data Sheet

4-CHANNEL SPEECH+MELODY PROCESSOR

(BandDirectorTM Series)

Publication Release Date: April 18, 2005

- 1 - Revision A5

Table of Contents-

1. GENERAL DESCRIPTION ......................................................................................................... 2

2. FEATURES ................................................................................................................................. 3

3. PIN DESCRIPTION..................................................................................................................... 4

4. BLOCK DIAGRAM ...................................................................................................................... 5

5. ELECTRICAL CHARACTERISTICS........................................................................................... 5

5.1 Absolute Maximum Ratings............................................................................................... 5

5.2 D.C. Characteristics........................................................................................................... 6

5.3 A.C. Characteristics ........................................................................................................... 6

6. APPLICATION CIRCUITS .......................................................................................................... 7

6.1 W567B010~B020 .............................................................................................................. 7

6.2 W567B030~B260 .............................................................................................................. 8

7. REVISION HISTORY .................................................................................................................. 9

W567BXXX

- 2 -

1. GENERAL DESCRIPTION

The W567Bxxx is a powerful microcontroller (uC) dedicated to speech and melody synthesis

applications. With the help of the embedded 8-bit microprocessor & dedicated H/W, the W567Bxxx

can synthesize 4-channel speech+melody simultaneously.

The two channels of synthesized speech can be in different kinds of format, for example ADPCM and

MDPCM. The W567Bxxx can provide 4-channel high-quality WinMelodyTM , which can emulate the

characteristics of musical instruments, such as piano and violin. The output of speech/melody

channels are mixed together through the on-chip digital mixer to produce colorful effects. With these

hardware resources, the W567Sxxx is very suitable for high-quality and sophisticated scenario

applications.

The W567Bxxx is also capable of transmitting infrared (IR) signals with on-chip carrier generator. As a

result, toys can be designed to interact with each other for more play values. A serial interface can be

supported as external memory for memory expansion or content-updateable applications.

The W567Bxxx family contains several items with different playback duration as shown below: (@5-bit

MDPCM algorithm, 6KHz sampling rate)

Item W567B010 W567B015 W567B020 W567B030 W567B040

*Duration 14 sec. 18 sec. 26 sec. 35 sec. 52 sec.

Item W567B060 W567B080 W567B100 W567B120 W567B150

Duration 60 sec. 104 sec. 116 sec. 129 sec. 163 sec.

Item W567B170 W567B210 W567B260

Duration 197 sec. 232 sec. 264 sec.

Note:

*: The duration time is based on 5-bit MDPCM at 6KHz sampling rate. The firmware library and timber library have

been excluded from user’s ROM space for the duration estimation.

W567BXXX

Publication Release Date :April 18, 2005

- 3 - Revision A5

2. FEATURES

• Wide range of operating voltage:

− 8 MHz @ 3.0 volt ~ 5.5 volt

− 4 MHz @ 2.4 volt ~ 5.5 volt

• Power management:

− 4 ~ 8 MHz system clocks, with Ring type and Crystal type

− Stop mode for stopping all IC operations

• Provides up to 8 inputs, 8 outputs and 24 I/O pins

• Current-type Digital-to-Analog Converter (DAC):

− (8+2)-bit resolution with programmable output current

• F/W speech synthesis with multiple format support: ADPCM/MDPCM/PCM

• 2 speech synthesis1 channels at programmable sample rate

• 4 melody channels that can emulate characteristics of musical instruments

• 4-input/8-bit-resolution Mixer can mix the speech and melody signals flexibly

• Built-in IR carrier generation circuit for simplifying firmware IR application

• Built-in 5 timers for speech/melody synthesis and general purpose applications

• Built-in 8*7 multiplier

• Built-in Watch-Dog Timer (WDT)

• Built-in Low-Voltage-Reset (LVR)

• Built-in Serial Interface Manager (SIM) in W567B030 ~ B260

• Support PowerScript for developing codes in easy way

• Full-fledged development system

− Source-level ICE debugger

− Event synchronization mechanism

− Compatible with W566B/C & W588S system

− User-friendly GUI environment

• Available package form: (COB is essential)

1 More speech channels are available for 8-bit PCM format in the remaining melody channels.

W567BXXX

- 4 -

3. PIN DESCRIPTION

PIN NAME I/O FUNCTION

RESETB In IC reset input, low active.

OSCI In Main-clock oscillation input. Mask option to select main-clock type. When

Ring type is used. Connect to GND via the oscillation resistor.

OSCO Out Main-clock oscillation output. Mask option to select main-clock type.

IP0[7:0] /

IP0[7:4]

In General input port with pull-high selection. Each 2 input pins can be

programmed to generate interrupt request and used to release IC from

STOP mode.

BP0[7:0] I/O General input/output pins. When used as output pin, it can be open–drain

or CMOS type and it can sink 8mA for high-current applications. When

used as input pin, there may have a pull-high option and generate

interrupt request to release IC from STOP mode.

When BP0[7] is used as output pin, it can be the IR transmission carrier

for IR applications.

BP1[7:0]

I/O General input/output pins. When used as output pin, it can be open–drain

or CMOS type. When used as input pin, there may have a pull-high

option and generate interrupt request to release IC from STOP mode.

When serial interface is enabled, BP1[6:4] are used as serial interface

pins.

BP2[7:0]

I/O General input/output pins. When used as output pin, it can be open–drain

or CMOS type. When used as input pin, there may have a pull-high

option and generate interrupt request to release IC from STOP mode.

OP0[7:0] Out General output pins. The pins of OP0 are Inverter-type output.

DAC Out Current type DAC speaker output.

TEST In Test input, internally pulled low. Do not connect during normal operation.

VDD Power Positive power supply for µP and peripherals.

VSS Power Negative power supply for µP and peripherals.

2VDDOSC Power Positive power supply for oscillation.

2VSSOSC Power Negative power supply for oscillation.

2 In order to get a stable oscillating frequency, W567B030~B260 provides these pins for power supply.

W567BXXX

Publication Release Date :April 18, 2005

- 5 - Revision A5

4. BLOCK DIAGRAM

Timing

Generator

8 bits uP

Data RAM

Program ROM Speaker

Driver

Interrupt

Controller

Timers

HQ generator I/O

WDT LVR Mixer

Address/Data Bus

BP1[7:0]

DAC

RESETB

IP0[7:0]

IP0[7:4]

OSCI

OSCO

Serial

Interface

BP1[6:4]

BP2[7:0]BP0[7:0]

OP0[7:0]

5. ELECTRICAL CHARACTERISTICS

5.1 Absolute Maximum Ratings

PARAMETER RATING UNIT

Supply Voltage to Ground Potential -0.3 to +7.0 V

D.C. Voltage on Any Pin to Ground Potential -0.3 to VDD +0.3 V

Operating Temperature 0 to +70 °C

Storage Temperature -55 to +150 °C

Note: Exposure to conditions beyond those listed under Absolute Maximum Ratings may adversely affect the life and reliability

of the device.

W567BXXX

- 6 -

5.2 D.C. Characteristics

(VDD −VSS = 4.5V, FM = 8 MHz, TA = 25°C, No Load unless otherwise specified)

SPEC.

PARAMETER SYM. TEST CONDITIONS

Min. Typ. Max.

UNIT

FSYS = 4 MHz 2.4 - 5.5 V

Operating Voltage VDD FSYS = 8 MHz 3.0 - 5.5 V

Operating Current IOP FSYS = FM, normal

operation - 15 20 mA

Standby Current ISB STOP mode - 1 2 µA

Input Low Voltage VIL All input pins VSS - 0.3 VDD V

Input High Voltage VIH All input pins 0.7 VDD - VDD V

Vout = 0.4V, all output

pins except BP0 - - 4 mA

Output Low Current IOL

Vout = 0.4V, BP0 only - - 8 mA

Output High Current IOH Vout = 2.4V, all output

pins -4 - - mA

DAC Full Scale Current IDAC VDD = 4.5V, RL = 100Ω -2.4

-4.0

-3.0

-5.0

-3.6

-6.0 mA

Operation Current of

Low Voltage Reset ILVR VDD = 4.5V 60 uA

All input pins except

RESETB 450 - - KΩ

Pull High Resistance RIN

RESERB 100 - -

KΩ

5.3 A.C. Characteristics

(VDD-VSS = 4.5V, FM = 8 MHz, TA = 25°C; No Load unless otherwise specified)

SPEC.

PARAMETER SYM. TEST CONDITIONS

Min. Typ. Max.

UNIT

Ring type, *Rosc = 300 KΩ3.6 4 4.4

Main-Clock FM

Ring type, *Rosc = 150 KΩ7.2 8 8.8

MHz

Cycle Time TCYC F

SYS = 8 MHz 125 - DC nS

Main-Clock Wake-up

Stable Time TWSM Ring type, R = 300 KΩ - 3 5 mS

Main-Clock Frequency

Deviation, Ring type F

F∆

MIN

MINMAX

F-F - 3 7.5 %

RESETB Active Width TRES After FSYS stable 4 - - TCYC

*: Typical ROSC value for each part number should refer to design guide.

W567BXXX

Publication Release Date :April 18, 2005

- 7 - Revision A5

6. APPLICATION CIRCUITS

6.1 W567B010~B020

W567B010

W567B020

ROSC

OSC

VDD

VSS

4.7uF

BP00

BP07

BP10

BP17

IP04

IP07

Battery

DAC

VDD

Speaker

8050

/RESET

0.1uF

Reset

Switch

Notes:

1. The typical value of Rosc is 150 KΩ for 8 MHz and 300 KΩ for 4 MHz, and should be connected to GND (VSS).

2. Please refer to design guide to get typical Rosc value for each part number.

3. The Rs value is suggested in 270Ω ~ 1KΩ to limit too large DAC output current flowing into transistor.

4. The capacitor, 4.7µF, shunts between VDD and GND is necessary as power stability. But the value of

capacitor is depend on the application.

5. The above application circuit is for reference only. No warranty for mass production.

W567BXXX

- 8 -

6.2 W567B030~B260

W567B030

W567B260

ROSC

OSC

VDD

VSS

/RESET

DAC

0.1uF

4.7uF

BP00

BP07

BP10

BP17

BP20

BP27

IP00

IP07

VDD

VDDOSC

0.1uF

Battery

VSSOSC

Reset

Switch

Speaker

8050

OP00

OP07

Notes:

1. The typical value of Rosc is 150 KΩ for 8 MHz and 300 KΩ for 4 MHz, and should be connected to GND (VSS).

2. Please refer to design guide to get typical Rosc value for each part number.

3. For W567B030~B260, VSSOSC should be connected to VSS; VDDOSC should be connected to VDD in PCB layout.

4. The Rs value is suggested in 270Ω ~ 1KΩ to limit too large DAC output current flowing into transistor.

5. The 10Ω and 0.1uF between VDD, VDDOSC and GND are optional to filter power noise.

6. The capacitor, 4.7uF, shunts between VDD and GND is necessary as power stability. But the value of capacitor is

depend on the application.

7. The above application circuit is for reference only. No warranty for mass production.

W567BXXX

Publication Release Date :April 18, 2005

- 9 - Revision A5

7. REVISION HISTORY

VERSION DATE PAGE DESCRIPTION

A1 Oct. 16, 2003 - Preliminary release.

A2 Nov 19, 2003 -

Rename VDD1/VSS1 to VDDOSC/VSSOSC

in the Pin Description

Update application circuit and notes.

A3 March 16, 2004 -

• Change the name Low-Voltage-Detect

(LVD) to Low-Voltage-Reset (LVR).

• Modify Pull High Resistance as 450K in

the DC Characteristics.

A4 June 18, 2004 - • Add the operation current of Low-

Voltage-Reset.

A5 APRIL 18, 2005 9 • ADD IMPORTANT NOTICE

Important Notice

Winbond products are not designed, intended, authorized or warranted for use as components

in systems or equipment intended for surgical implantation, atomic energy control

instruments, airplane or spaceship instruments, transportation instruments, traffic signal

instruments, combustion control instruments, or for other applications intended to support or

sustain life. Further more, Winbond products are not intended for applications wherein failure

of Winbond products could result or lead to a situation wherein personal injury, death or

severe property or environmental damage could occur.

Winbond customers using or selling these products for use in such applications do so at their

own risk and agree to fully indemnify Winbond for any damages resulting from such improper

use or sales.

Headquarters

No. 4, Creation Rd. III,

Science-Based Industrial Park,

Hsinchu, Taiwan

TEL: 886-3-5770066

FAX: 886-3-5665577

http://www.winbond.com.tw/

Taipei Office

TEL: 886-2-8177-7168

FAX: 886-2-8751-3579

Winbond Electronics Corporation America

2727 North First Street, San Jose,

CA 95134, U.S.A.

TEL: 1-408-9436666

FAX: 1-408-5441798

Winbond Electronics (H.K.) Ltd.

No. 378 Kwun Tong Rd.,

Kowloon, Hong Kong

FAX: 852-27552064

Unit 9-15, 22F, Millennium City,

TEL: 852-27513100

Please note that all data and specifications are subject to change without notice.

All the trade marks of products and companies mentioned in this data sheet belong to their respective owners.

Winbond Electronics (Shanghai) Ltd.

200336 China

FAX: 86-21-62365998

27F, 2299 Yan An W. Rd. Shanghai,

TEL: 86-21-62365999

Winbond Electronics Corporation Japan

Shinyokohama Kohoku-ku,

Yokohama, 222-0033

FAX: 81-45-4781800

7F Daini-ueno BLDG, 3-7-18

TEL: 81-45-4781881

9F, No.480, Rueiguang Rd.,

Neihu District, Taipei, 114,

Taiwan, R.O.C.