FUJITSU SEMICONDUCTOR DATA SHEET DS05-13103-4E Memory FRAM CMOS 1 M Bit (128 K x 8) MB85R1001 DESCRIPTIONS The MB85R1001 is an FRAM (Ferroelectric Random Access Memory) chip consisting of 131,072 words x 8 bits of non-volatile memory cells created using ferroelectric process and silicon gate CMOS process technologies. The MB85R1001 is able to retain data without using a back-up battery, as is needed for SRAM. The memory cells used in the MB85R1001 can be used for at least 1010 read/write operations, which is a significant improvement over the number of read and write operations supported by Flash memory and E2PROM. The MB85R1001 uses a pseudo-SRAM interface that is compatible with conventional asynchronous SRAM. FEATURES * * * * * * Bit configuration Read/write endurance Operating power supply voltage Operating temperature range Data retention Package : 131,072 words x 8bits : 1010 times/bit (Min) : 3.0 V to 3.6 V : - 20 C to + 85 C : 10 years ( + 55 C) : 48-pin plastic TSOP (1) Copyright(c)2005-2007 FUJITSU LIMITED All rights reserved MB85R1001 PIN ASSIGNMENTS (TOP VIEW) A11 A9 NC A8 A13 WE CE2 A15 NC VCC NC NC GND NC NC VCC NC A16 A14 A12 A7 A6 A5 A4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 OE NC GND A10 CE1 NC I/O8 I/O7 I/O6 I/O5 I/O4 VCC NC I/O3 I/O2 I/O1 NC NC NC A0 A1 GND A2 A3 (FPT-48P-M25) PIN DESCRIPTIONS Pin name A0 to A16 Address In I/O1 to I/O8 Data Input/Output CE1 Chip Enable 1 in CE2 Chip Enable 2 in WE Write Enable in OE Output Enable in VCC Power Supply GND Ground NC 2 Function No Connection MB85R1001 BLOCK DIAGRAM to * * * Address Latch. A0 Row Dec. Ferro Capacitor Cell A16 Column Dec. intCE2 S/A intCE2 CE2 intOE intWE intCE2 intCEB WE I/O1 to I/O8 OE I/O8 CE1 * * intCEB to I/O1 FUNCTION TRUTH TABLE Operation Mode Standby Pre-charge Read Read (Pseudo-SRAM, OE control) CE1 CE2 WE OE H X X X X L X X X X H H H L H L L H L High-Z Standby (ISB) H L Operation (ICC) H L Write (Pseudo-SRAM, WE control) Supply Current Dout H Write I/O1 to I/O8 Din H H L = VIL, H = VIH, X can be either VIL or VIH, High-Z = High Impedance : Latch address and latch data at falling edge, : Latch address and latch data at rising edge 3 MB85R1001 ABSOLUTE MAXIMUM RATINGS Parameter Symbol Rating Min Max Unit Supply Voltage* VCC -0.5 +4.0 V Input Voltage* VIN -0.5 VCC+0.5 V VOUT -0.5 VCC+0.5 V TA -20 +85 C Tstg -40 +125 C Output Voltage* Ambient Operating Temperature Storage Temperature * : All voltages are referenced to VSS. WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings. RECOMMENDED OPERATING CONDITIONS Parameter Symbol Value Min Typ Max Unit Supply Voltage* VCC 3.0 3.3 3.6 V Input Voltage (high)* VIH VCC x 0.8 VCC + 0.5 V Input Voltage (low)* VIL -0.5 +0.8 V Operating Temperature TA -20 +85 C * : All voltages are referenced to VSS. WARNING: The recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. All of the device's electrical characteristics are warranted when the device is operated within these ranges.Always use semiconductor devices within their recommended operating condition ranges. Operation outside these ranges may adversely affect reliability and could result in device failure. No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. Users considering application outside the listed conditions are advised to contact their FUJITSU representatives beforehand. 4 MB85R1001 ELECTRICAL CHARACTERISTICS 1. DC CHARACTERISTICS Parameter Symbol Test Condition (within recommended operating conditions) Value Unit Min Typ Max Input Leakage Current |ILI| VIN = 0 V to VCC 10 A Output Leakage Current |ILO| VOUT = 0 V to VCC, CE1 = VIH or OE = VIH 10 A Supply Current ICC CE1 = 0.2 V, CE2 = VCC-0.2 V, Iout = 0 mA*1 15 mA 10 50 A VCC x 0.8 V 0.4 V CE1 VCC-0.2 V Standby Current ISB CE2 0.2 V*2 OE VCC-0.2 V, WE VCC-0.2 V*2 Output Voltage (high) VOH IOH = -0.1 mA Output Voltage (low) VOL IOL = 2.0 mA *1 : During the measurement of ICC , the Address, Data In were taken to only change once per active cycle. Iout : output current *2 : All pins other than setting pins should be input at the CMOS level voltages such as H VCC - 0.2 V, L 0.2 V. 5 MB85R1001 2. AC CHARACTERISTICS * AC TEST CONDITIONS Supply Voltage Operating Temperature Input Voltage Amplitude Input Rising Time Input Falling Time Input Evaluation Level Output Evaluation Level Output Impedance : 3.0 V to 3.6 V : -20 C to +85 C : 0.3 V to 2.7 V : 5 ns : 5 ns : 2.0 V / 0.8 V : 2.0 V / 0.8 V : 50 pF (1) Read Operation (within recommended operating conditions) Parameter Symbol Value Min Max Unit Read Cycle Time tRC 150 ns CE1 Active Time tCA1 120 2000 ns OE Active Time tRP 120 2000 ns Pre-charge Time tPC 20 ns Address Setup Time tAS 0 ns Address Hold Time tAH 50 ns OE Setup Time tES 0 ns Output Hold Time tOH 0 ns Output Set Time tLZ 30 ns CE1 Access Time tCE1 100 ns CE2 Access Time tCE2 100 ns OE Access Time tOE 100 ns Output Floating Time tOHZ 20 ns (2) Write Operation (within recommended operating conditions) Parameter 6 Symbol Value Min Max Unit Write Cycle Time tWC 150 ns CE1 Active Time tCA1 120 2000 ns CE2 Active Time tCA2 120 2000 ns Pre-charge Time tPC 20 ns Address Setup Time tAS 0 ns Address Hold Time tAH 50 ns Write Pulse Width tWP 120 ns Data Setup Time tDS 0 ns Data Hold Time tDH 50 ns Write Setup Time tWS 0 ns MB85R1001 (3) Power ON/OFF Sequence (within recommended operating conditions) Value Symbol Min Typ Max CE1 level hold time for Power OFF tpd 85 ns CE1 level hold time for Power ON tpu 85 ns Parameter Unit 3. Pin Capacitance (f = 1 MHz, TA = +25 C) Parameter Input Capacitance Output Capacitance Symbol CIN COUT Test Condition Value Unit Min Typ Max VIN = GND 10 pF VOUT = GND 10 pF 7 MB85R1001 TIMING DIAGRAMS 1. Read Cycle Timing (CE1, CE2 Control) tRC tCA1 tCE1 tPC CE1 CE2 tCE2 tAS A0 to A16 tAH Valid H or L tES tRP OE tOH tLZ tOHZ tOE I/O1 to I/O8 High-Z Valid Invalid Invalid 2. Read Cycle Timing (OE Control) tCA1 CE1 CE2 tCA2 tAS A0 to A16 tAH Valid H or L tRC tPC tRP OE tOH tLZ tOHZ tOE I/O1 to I/O8 Valid Invalid 8 Invalid High-Z MB85R1001 3. Write Cycle Timing (CE1, CE2 Control) tWC tCA1 tPC CE1 CE2 tCA2 tAH tAS A0 to A16 Valid H or L tWS tWP WE tDS tDH High-Z Valid Data In H or L 4. Write Cycle Timing (WE Control) tCA1 CE1 tCA2 CE2 tAS A0 to A16 tAH Valid H or L tWC tWP tPC WE tDS tDH High-Z Data In Valid H or L 9 MB85R1001 POWER ON/OFF SEQUENCE tpd tpu VCC VCC CE2 CE2 3.0 V 3.0 V VIH (Min) VIH (Min) 1.0 V 1.0 V VIL (Max) VIL (Max) CE2 0.2 V GND GND CE1 > VCC x 0.8* CE1 CE1 : Don't Care CE1 > VCC x 0.8* CE1 * : CE1 (Max) < VCC + 0.5 V Note : You can choose either of CE1 or CE2, or both for disenable control of the device. NOTES ON USE Data that is written prior to IR reflow is not guaranteed to be retained after IR reflow. ORDERING INFOMATION Part number MB85R1001PFTN 10 Package 48-pin plastic TSOP(1) (FPT-48P-M25) MB85R1001 PACKAGE DIMENSIONS 48-pin plastic TSOP(1) Lead pitch 0.50 mm Package width x package length 12.00 x 12.40 mm Lead shape Gullwing Sealing method Plastic mold Mounting height 1.20 mm MAX Weight 0.37 g Code (Reference) P-TSOP(1)48-12x12.4-0.50 (FPT-48P-M25) 48-pin plastic TSOP(1) (FPT-48P-M25) Note 1) *1 : Resin protrusion. (Each side : +0.15 (.006) Max). Note 2) *2 : These dimensions do not include resin protrusion. Note 3) Pins width and pins thickness include plating thickness. Note 4) Pins width do not include tie bar cutting remainder. 0.100.05 (Stand off) (.004.002) LEAD No. 1 48 0.50(.020) INDEX +0.05 0.22 -0.04 +.002 .009 -.002 *1 12.000.10 (.472.004) 24 0.10(.004) M 25 1.130.07 (Mounting height) (.044.003) 14.000.20(.551.008) Details of "A" part *2 12.400.10(.488.004) "A" 0~8 +0.05 0.08(.003) C 0.145 -0.03 +.002 .006 -.001 2003 FUJITSU LIMITED F48043S-c-2-2 0.25(.010) 0.600.15 (.024.006) Dimensions in mm (inches). Note: The values in parentheses are reference values Please confirm the latest Package dimension by following URL. http://edevice.fujitsu.com/fj/DATASHEET/ef-ovpklv.html 11 MB85R1001 FUJITSU LIMITED All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with FUJITSU sales representatives before ordering. The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose of reference to show examples of operations and uses of Fujitsu semiconductor device; Fujitsu does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information. Fujitsu assumes no liability for any damages whatsoever arising out of the use of the information. Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of Fujitsu or any third party or does Fujitsu warrant non-infringement of any third-party's intellectual property right or other right by using such information. Fujitsu assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein. The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite). Please note that Fujitsu will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the prior authorization by Japanese government will be required for export of those products from Japan. The company names and brand names herein are the trademarks or registered trademarks of their respective owners. Edited Business Promotion Dept. F0704