CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Upgrade! NPCAP TM Super PSF - Radial Lead Series low ESR, high ripple current capability 5mmax. (2 to 4Vdc) Longer life (5,000 hours at 105) ESR after endurance is specified within the initial spec (2 to 4Vdc) Rated voltage range : 2 to 16Vdc RoHS Compliant Halogen Free PSF ESR Lower ESR PSE SPECIFICATIONS Items Characteristics Category Temperature Range Rated Voltage Range Capacitance Tolerance Surge Voltage Leakage Current *Note -55 to +105 2 to 16Vdc 20% (M) Rated voltage(V)x1.15 Shall not exceed values shown in STANDARD RATINGS. Dissipation Factor (tan) 0.10 max. Low Temperature Characteristics (Max.Impedance Ratio) Z(-25)/Z(+20)1.15 Z(-55)/Z(+20)1.25 Endurance Bias Humidity Test Surge Voltage Test Failure Rate (at 20, 120Hz) (at 105) (at 20 after 2 minutes) (at 20, 120Hz) (at 100kHz) The following specifications shall be satisfied when the capacitors are restored to 20 after the rated voltage is applied for 5,000 hours at 105. Appearance No significant damage Capacitance change 20% of the initial value D.F. (tan) The initial specified value ESR 2 to 4Vdc : The initial specified value 16Vdc : 150% of the initial specified value Leakage current The initial specified value The following specifications shall be satisfied when the capacitors are restored to 20 after subjecting them to DC voltage at 60, 90 to 95% RH for 1,000 hours. Appearance No significant damage Capacitance change 20% of the initial value D.F. (tan) The initial specified value ESR 2 to 4Vdc : The initial specified value 16Vdc : 150% of the initial specified value Leakage current The initial specified value The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105 for 30 seconds through a protective resistor(R=1k) and discharge for 5 minutes 30 seconds. Appearance No significant damage Capacitance change 20% of the initial value D.F. (tan) The initial specified value ESR 2 to 4Vdc : The initial specified value 16Vdc : 150% of the initial specified value Leakage current The initial specified value 0.5% per 1,000 hours maximum (Confidence level 60% at 105) *Note : If any doubt arises, measure the leakage current after the following voltage treatment. Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105. DIMENSIONS [mm] Code : E Coated Case Size code F05 F08 D 6.3 d 0.45 0.6 F 2.5 D' L' L+1.0max. D' d F05, F08, H08 F0.5 Terminal 15min. F0.5 d D' (FA5) L' 15min. H08 HB5 8.0 JB5 10.0 0.6 0.5 3.5 D+0.5max. L+0.3max. L+1.0max. 5.0 L+1.5max. 4min. Coated Case F0.5 L' FA5, HB5, JB5 FA5 (HB5, JB5) MARKING EX) 2.5V560F F 6D6 560 2.5V 4min. Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. (1/2) CAT. No. E1001M CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Upgrade! NPCAP TM PSF - Radial Lead Series PART NUMBERING SYSTEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 A PS F 2 R 5 E AA 5 6 1 M F 0 8 S Supplement code Size code Capacitance tolerance code Capacitance code (ex. 560F:561) Lead forming*Taping code Terminal code Voltage code (ex. 2.5V:2R5, 16V:160) Series code Category Please refer to "Product code guide (conductive polymer type)" STANDARD RATINGS WV(Vdc) Cap(F) 2 1,000 330 470 560 820 1,200 1,600 470 560 100 100 270 270 330 470 470 2.5 4 16 Case size DxL(mm) 6.3x8 6.3x8 6.3x8 6.3x8 6.3x8 6.3x8 8x8 6.3x8 6.3x8 6.3x5 6.3x10.5 8x8 8x11.5 8x8 8x11.5 10x11.5 ESR Leakage current (m max./20, (Amax/after 2min.) 100k to 300kHz) 500 500 500 500 500 1,200 800 500 500 500 500 864 864 1,050 1,500 1,500 5 5 5 5 5 5 5 5 5 24 25 10 11 13 11 10 Rated ripple current (mArms/105, 100kHz) 5,900 5,900 5,900 5,900 5,900 5,900 6,100 5,900 5,900 2,490 2,820 5,000 5,080 4,700 5,400 6,100 Part No. APSF2R0E102MF08S APSF2R5E331MF08S APSF2R5E471MF08S APSF2R5E561MF08S APSF2R5E821MF08S APSF2R5E122MF08S APSF2R5E162MH08S APSF4R0E471MF08S APSF4R0E561MF08S APSF160E101MF05S APSF160E101MFA5S APSF160E271MH08S APSF160E271MHB5S APSF160E331MH08S APSF160E471MHB5S APSF160E471MJB5S : Enter the appropriate lead forming or taping code. Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. (2/2) CAT. No. E1001M