Q2016LH4 - Teccor Electronics, Inc.

Teccor Electronics http://www.teccor.com

+1 972-580-7777 4 - 1

Thyristor Product Catalog

Selected Packages*

U.L. RECOGNIZED

File #E71639

Alternistor Triacs

(6 – 40 Amps)

General Description

Teccor offers bidirectional alternistors with current ratings from

6 to 40 amperes and voltages from 200 to 1000 volts as part of

Teccor's broad line of thyristors. Teccor's alternistor has been

specifically designed for applications that switch highly inductive

loads. A special chip offers the same performance as two thyris-

tors (SCRs) wired inverse parallel (back-to-back), providing bet-

ter turn-off behavior than a standard triac. An alternistor may be

triggered from a blocking to conduction state for either polarity of

applied AC voltage with operating modes in Quadrants I, II, and

III.

This new chip construction provides two electrically separate

SCR structures, providing enhanced dv/dt characteristics while

retaining the advantages of a single chip device.

All alternistors have glass-passivated junctions to ensure long

term reliability and parameter stability. Teccor's glass offers a reli-

able barrier against junction contamination.

These alternistors are offered in TO-218X, TO-218AC, FastPak,

and TO-220AB packages. Teccor's TO-218X package has been

designed for heavy, steady power-handling capability. It features

large eyelet terminals for ease of soldering heavy gauge hook-up

wire. All the isolated packages have a standard isolation voltage

rating of 2500VRMS.

Variations of devices covered in this data sheet are available for

custom design applications. Please consult factory for further

information.

Features

• High surge current capability

• Glass-passivated junctions

• 2500VAC isolation for “L,” “J,” “P,” and “K”

• High commutating dv/dt

• High static dv/dt

TO-220AB

THERMOTAB

TO-218AC

TO-218X

FASTPAK

MT2 MT1

Alternistor Triacs Thyristor Product Catalog

http://www.teccor.com Teccor Electronics

4 - 2 +1 972-580-7777

See General Notes and Electrical Specification Notes on page 6.

** Consult factory for 1000 volt device.

IT(RMS)

Part Number

VDRM IGT IDRM VGT

Isolated Non-Isolated

RMS

On-State

Current

Conduction

Angle of

360o

(4)(16)

THERMOTAB

T0-220AB

TO-218AC

(16)

TO-218X FASTPAK

TO-3 BASE

TO-220AB

Repetitive

Peak

Blocking

Voltage (1)

Volts

DC Gate Trigger

Current in

Specific Operating

Quadrants

VD=12VDC

(3) (7) (15) (17)

mAmps

Peak Off-State

Current Gate Open

VDRM=Max

Rated Value

(1) (18)

mAmps

DC Gate

Trigger

Voltage

VD=12VDC

(2) (6)

(15) (17)

Volts

QI QII QIII

TC =

25°C

TC =

100°C

TC =

125°C

TC =

125°C

TC =

25°C

MAX See “Package Dimensions” section for variations. (11) MIN MAX MAX MIN MAX

Amps

Q2006LH4 Q2006RH4 200 35 35 35 0.01 0.5 2.0 0.2 1.5

Q4006LH4 Q4006RH4 400 35 35 35 0.01 0.5 2.0 0.2 1.5

Q5006LH4 Q5006RH4 500 35 35 35 0.01 0.5 2.0 0.2 1.5

Q6006LH4 Q6006RH4 600 35 35 35 0.01 0.5 2.0 0.2 1.5

Q7006LH4 Q7006RH4 700 35 35 35 0.01 0.5 2.0 0.2 1.5

**Q8006LH4 **Q8006RH4 800 35 35 35 0.01 0.5 2.0 0.2 1.5

Amps

Q2008LH4 Q2008RH4 200 35 35 35 0.01 0.5 2.0 0.2 1.5

Q4008LH4 Q4008RH4 400 35 35 35 0.01 0.5 2.0 0.2 1.5

Q5008LH4 Q5008RH4 500 35 35 35 0.01 0.5 2.0 0.2 1.5

Q6008LH4 Q6008RH4 600 35 35 35 0.01 0.5 2.0 0.2 1.5

Q7008LH4 Q7008RH4 700 35 35 35 0.01 0.5 2.0 0.2 1.5

**Q8008LH4 **Q8008RH4 800 35 35 35 0.01 0.5 2.0 0.2 1.5

Amps

Q2010LH5 Q2010RH5 200 50 50 50 0.01 0.5 2.0 0.2 1.5

Q4010LH5 Q4010RH5 400 50 50 50 0.01 0.5 2.0 0.2 1.5

Q5010LH5 Q5010RH5 500 50 50 50 0.01 0.5 2.0 0.2 1.5

Q6010LH5 Q6010RH5 600 50 50 50 0.01 0.5 2.0 0.2 1.5

Q7010LH5 Q7010RH5 700 50 50 50 0.01 0.5 2.0 0.2 1.5

**Q8010LH5 **Q8010RH5 800 50 50 50 0.01 0.5 2.0 0.2 1.5

Amps

Q2012LH5 Q2012RH5 200 50 50 50 0.01 0.5 2.0 0.2 1.5

Q4012LH5 Q4012RH5 400 50 50 50 0.01 0.5 2.0 0.2 1.5

Q5012LH5 Q5012RH5 500 50 50 50 0.01 0.5 2.0 0.2 1.5

Q6012LH5 Q6012RH5 600 50 50 50 0.01 0.5 2.0 0.2 1.5

Q7012LH5 Q7012RH5 700 50 50 50 0.01 0.5 2.0 0.2 1.5

**Q8012LH5 **Q8012RH5 800 50 50 50 0.01 0.5 2.0 0.2 1.5

MT1 MT2 G

MT1

MT2

MT1

MT2

MT1 G

MT2

Thyristor Product Catalog Alternistor Triacs

Teccor Electronics http://www.teccor.com

+1 972-580-7777 4 - 3

See General Notes and Electrical Specification Notes on page 6.

VTM IHIGTM PGM PG(AV) ITSM dv/dt (c) dv/dt tgt I2tdi/dt

Peak

On-State

Voltage at

Max Rated

RMS Current

TC = 25°C

(1) (5)

Volts

Holding

Current

(DC)

Gate Open

(1) (8) (12)

mAmps

Peak Gate

Trigger

Current

(14)

Amps

Peak Gate

Power

Dissipation

(14)

IGT ≤ IGTM

Watts

Average

Gate Power

Dissipation

Watts

Peak One

Cycle

Surge

(9) (13)

Amps

Critical Rate-of-Rise

of Commutation Voltage

at Rated

VDRM and IT(RMS)

Commutating di/dt = 0.54

Rated IT(RMS)/ms

Gate Unenergized

(1) (4) (13)

Volts/µSec

Critical

Rate-of-Rise of

Off-State

Voltage at

Rated VDRM

Gate Open

(1)

Volts/µSec

Gate

Controlled

Turn-On

Time

IGT = 300mA

0.1µs Rise

Time

(10)

µSec

RMS Surge

(Non-

Repetitive)

On-State

Current for

period of

8.3 ms

for Fusing

Amps2Sec

Maximum

Rate -of-

Change

of On-State

Current

(19)

Amps/µSec60Hz 50Hz

TC =

100°C

TC =

125°C

MAX MAX MIN MIN TYP

1.6 35 1.6 18 0.5 80 65 20 750 600 426.5 70

1.6 35 1.6 18 0.5 80 65 20 575 450 426.5 70

1.6 35 1.6 18 0.5 80 65 20 500 400 426.5 70

1.6 35 1.6 18 0.5 80 65 20 425 350 426.5 70

1.6 35 1.6 18 0.5 80 65 20 375 300 426.5 70

1.6 35 1.6 18 0.5 80 65 20 300 250 426.5 70

1.6 35 2.0 20 0.5 100 83 25 750 600 4 41 70

1.6 35 2.0 20 0.5 100 83 25 575 450 4 41 70

1.6 35 2.0 20 0.5 100 83 25 500 400 4 41 70

1.6 35 2.0 20 0.5 100 83 25 425 350 4 41 70

1.6 35 2.0 20 0.5 100 83 25 375 300 4 41 70

1.6 35 2.0 20 0.5 100 83 25 300 250 4 41 70

1.6 50 2.0 20 0.5 120 110 30 1150 1000 460 70

1.6 50 2.0 20 0.5 120 110 30 1000 750 460 70

1.6 50 2.0 20 0.5 120 110 30 925 700 460 70

1.6 50 2.0 20 0.5 120 110 30 850 650 460 70

1.6 50 2.0 20 0.5 120 110 30 775 600 460 70

1.6 50 2.0 20 0.5 120 110 30 650 500 460 70

1.6 50 2.0 20 0.5 120 110 30 1150 1000 4 60 70

1.6 50 2.0 20 0.5 120 110 30 1000 750 4 60 70

1.6 50 2.0 20 0.5 120 110 30 925 700 4 60 70

1.6 50 2.0 20 0.5 120 110 30 850 650 4 60 70

1.6 50 2.0 20 0.5 120 110 30 775 600 4 60 70

1.6 50 2.0 20 0.5 120 110 30 650 500 4 60 70

Alternistor Triacs Thyristor Product Catalog

http://www.teccor.com Teccor Electronics

4 - 4 +1 972-580-7777

See General Notes and Electrical Specification Notes on page 6.

** Consult factory for 1000 volt device

IT(RMS)

Part Number

VDRM IGT IDRM VGT

Isolated Non-Isolated

RMS

On-State

Current

Conduction

Angle of

360o

(4)(16)

THERMOTAB

T0-220AB

TO-218AC

(16)

TO-218X FASTPAK

TO-3 BASE

TO-220AB

Repetitive

Peak

Blocking

Voltage (1)

Volts

DC Gate Trigger

Current in

Specific Operating

Quadrants

VD=12VDC

(3) (7) (15) (17)

mAmps

Peak Off-State

Current Gate Open

VDRM=Max

Rated Value

(1) (18)

mAmps

DC Gate

Trigger

Voltage

VD=12VDC

(2) (6)

(15) (17)

Volts

QI QII QIII

TC =

25°C

TC =

100°C

TC =

125°C

TC =

125°C

TC =

25°C

MAX See “Package Dimensions” section for variations. (11) MIN MAX MAX MIN MAX

Amps

Q2016LH3 Q2016RH3 200 20 20 20 .05 0.5 2.0 0.2 1.5

Q4016LH3 Q4016RH3 400 20 20 20 .05 0.5 2.0 0.2 1.5

Q5016LH3 Q5016RH3 500 20 20 20 .05 0.5 2.0 0.2 1.5

Q6016LH3 Q6016RH3 600 20 20 20 .05 0.5 2.0 0.2 1.5

Q7016LH3 Q7016RH3 700 20 20 20 0.1 1.0 3.0 0.2 1.5

**Q8016LH3 **Q8016RH3 800 20 20 20 0.1 1.0 3.0 0.2 1.5

Q2016LH4 Q2016RH4 200 35 35 35 .05 0.5 2.0 0.2 2.0

Q4016LH4 Q4016RH4 400 35 35 35 .05 0.5 2.0 0.2 2.0

Q5016LH4 Q5016RH4 500 35 35 35 .05 0.5 2.0 0.2 2.0

Q6016LH4 Q6016RH4 600 35 35 35 .05 0.5 2.0 0.2 2.0

Q7016LH4 Q7016RH4 700 35 35 35 0.1 1.0 3.0 0.2 2.0

**Q8016LH4 **Q8016RH4 800 35 35 35 0.1 1.0 3.0 0.2 2.0

Q2016LH6 Q2016RH6 200 80 80 80 .05 0.5 2.0 0.2 2.5

Q4016LH6 Q4016RH6 400 80 80 80 .05 0.5 2.0 0.2 2.5

Q5016LH6 Q5016RH6 500 80 80 80 .05 0.5 2.0 0.2 2.5

Q6016LH6 Q6016RH6 600 80 80 80 .05 0.5 2.0 0.2 2.5

Q7016LH6 Q7016RH6 700 80 80 80 0.1 1.0 3.0 0.2 2.5

**Q8016LH6 **Q8016RH6 800 80 80 80 0.1 1.0 3.0 0.2 2.5

Amps

Q2025L6 Q2025K6 Q2025J6 Q2025P Q2025R6 200 80 80 80 .05 0.5 2.0 0.2 2.5

Q4025L6 Q4025K6 Q4025J6 Q4025P Q4025R6 400 80 80 80 .05 0.5 2.0 0.2 2.5

Q5025L6 Q5025K6 Q5025J6 Q5025P Q5025R6 500 80 80 80 .05 0.5 2.0 0.2 2.5

Q6025L6 Q6025K6 Q6025J6 Q6025P Q6025R6 600 80 80 80 .05 0.5 2.0 0.2 2.5

Q7025L6 Q7025K6 Q7025J6 Q7025P Q7025R6 700 80 80 80 0.1 1.0 3.0 0.2 2.5

**Q8025L6 **Q8025K6 Q8025J6 Q8025P **Q8025R6 800 80 80 80 0.1 1.0 3.0 0.2 2.5

Amps

Q2040K7 Q2040J7 Q2040P 200 100 100 100 0.2 2.0 5.0 0.2 2.5

Q4040K7 Q4040J7 Q4040P 400 100 100 100 0.2 2.0 5.0 0.2 2.5

Q5040K7 Q5040J7 Q5040P 500 100 100 100 0.2 2.0 5.0 0.2 2.5

Q6040K7 Q6040J7 Q6040P 600 100 100 100 0.2 2.0 5.0 0.2 2.5

Q7040K7 Q7040J7 Q7040P 700 100 100 100 0.2 2.0 5.0 0.2 2.5

**Q8040K7 Q8040J7 Q8040P 800 100 100 100 0.2 2.0 5.0 0.2 2.5

MT1 MT2 G

MT1

MT2

MT1

MT2

MT1 G

MT2

Thyristor Product Catalog Alternistor Triacs

Teccor Electronics http://www.teccor.com

+1 972-580-7777 4 - 5

See General Notes and Electrical Specification Notes on page 6.

VTM IHIGTM PGM PG(AV) ITSM dv/dt (c) dv/dt tgt I2tdi/dt

Peak

On-State

Voltage at

Max Rated

RMS Current

TC = 25°C

(1) (5)

Volts

Holding

Current

(DC)

Gate Open

(1) (8) (12)

mAmps

Peak Gate

Trigger

Current

(14)

Amps

Peak Gate

Power

Dissipation

(14)

IGT ≤ IGTM

Watts

Average

Gate Power

Dissipation

Watts

Peak One

Cycle

Surge

(9) (13)

Amps

Critical Rate-of-Rise

of Commutation Voltage

at Rated

VDRM and IT(RMS)

Commutating di/dt = 0.54

Rated IT(RMS)/ms

Gate Unenergized

(1) (4) (13)

Volts/µSec

Critical

Rate-of-Rise of

Off-State

Voltage at

Rated VDRM

Gate Open

(1)

Volts/µSec

Gate

Controlled

Turn-On

Time

IGT = 300mA

0.1µs Rise

Time

(10)

µSec

RMS Surge

(Non-

Repetitive)

On-State

Current for

period of

8.3 ms

for Fusing

Amps2Sec

Maximum

Rate -of-

Change

of On-State

Current

(19)

Amps/µSec60Hz 50Hz

TC =

100°C

TC =

125°C

MAX MAX MIN MIN TYP

1.6 35 2.0 20 0.5 200 167 20 500 400 3166 100

1.6 35 2.0 20 0.5 200 167 20 400 350 3166 100

1.6 35 2.0 20 0.5 200 167 20 300 250 3166 100

1.6 35 2.0 20 0.5 200 167 20 275 200 3166 100

1.6 50 2.0 20 0.5 200 167 25 650 500 3166 100

1.6 50 2.0 20 0.5 200 167 25 600 475 3166 100

1.6 50 2.0 20 0.5 200 167 25 550 425 3166 100

1.6 50 2.0 20 0.5 200 167 25 500 400 3166 100

1.6 50 2.0 20 0.5 200 167 25 425 350 3166 100

1.6 70 2.0 20 0.5 200 167 30 875 600 5166 100

1.6 70 2.0 20 0.5 200 167 30 800 520 5166 100

1.6 70 2.0 20 0.5 200 167 30 700 475 5166 100

1.8 100 2.0 20 0.5 250 208 30 875 600 5 259 100

1.8 100 2.0 20 0.5 250 208 30 800 520 5 259 100

1.8 100 2.0 20 0.5 250 208 30 700 475 5 259 100

1.8 120 4.0 40 0.8 400 335 50 1100 700 5664 150

1.8 120 4.0 40 0.8 400 335 50 1000 625 5664 150

1.8 120 4.0 40 0.8 400 335 50 900 575 5664 150

Alternistor Triacs Thyristor Product Catalog

http://www.teccor.com Teccor Electronics

4 - 6 +1 972-580-7777

General Notes

• All measurements are made at 60Hz with a resistive load at an

ambient temperature of +25°C unless specified otherwise.

• Operating temperature range (TJ) is -40°C to +125°C except 0°C to

+125°C for FastPaks.

• Storage temperature range (TS) is -40°C to +125°C except -20°C to

+125°C for FastPaks.

• Lead solder temperature is a maximum of 230°C for 10 seconds

maximum ≥ 1/16" (1.59mm) from case.

• The case temperature (TC) is measured as shown on the dimen-

sional outline drawings. See “Package Dimensions” section of this

catalog.

Electrical Specification Notes

(1) For either polarity of MT2 with reference to MT1 terminal.

(2) For either polarity of gate voltage (VGT) with reference to MT1 ter-

minal.

(3) See Definition of Quadrants.

(4) See Figures 4.1 through 4.4 for current rating at specific operating

temperature and Figure 4.16 for free air rating (no heat sink).

(5) See Figures 4.5 and 4.6 for iT and vT

(6) See Figure 4.7 for VGT vs TC.

(7) See Figure 4.8 for IGT vs TC.

(8) See Figure 4.9 for IH vs TC.

(9) See Figures 4.10 and 4.11 for surge rating with specific durations.

(10) See Figure 4.12 for tgt vs IGT.

(11) See package outlines for lead form configurations. When ordering

special lead forming, add type number as suffix to part number.

(12) Initial on-state current = 400 mA(DC) for 16-40A devices and

100mA for 6-12 Amp devices.

(13) See Figures 4.1 through 4.4 for maximum allowable case temper-

ature at maximum rated current.

(14) Pulse width ≤ 10µs.

(15) For 6-12 Amp devices, RL = 60Ω; 16 Amp and above, RL = 30Ω

(16) 40 Amp pin terminal leads on K package can run 100°C to 125°C.

(17) Alternistor does not turn on in Quadrant IV.

(18) Tc = TJ for test conditions in off-state

(19) IGT = 200 mA for 6-12 Amp devices and 500 mA for 16-40 Amp

devices with gate pulse having rise time of ≤ 0.1 microsecond.

Gate Characteristics

Teccor triacs may be turned on in the following ways:

• With in-phase signals (using standard AC line) Quadrants I and

III are used.

• By applying unipolar pulses (gate always negative)—with nega-

tive gate pulses Quadrants II and III are used.

In all cases, if maximum surge capability is required, gate pulses

should be a minimum of one magnitude above minimum IGT rat-

ing with a steep rising waveform (≤1µs rise time).

Definition of Quadrants

Electrical Isolation

Teccor’s isolated Alternistor packages will withstand a minimum

high potential test of 2500 VAC (RMS) from leads to mounting

tab, over the operating temperature range of the device. See iso-

lation table below for standard and optional isolation ratings.

* For 4000V isolation, use V suffix in part number.

** UL Recognized File E71639

ELECTRICAL ISOLATION

FROM LEADS TO MOUNTING TAB **

VAC

(RMS) Isolated

TO-218AC

Isolated

FASTPAK

Isolated

TO-220AB

Isolated

TO-218X

2500 Standard Standard Standard Standard

4000 N/A N/A Optional * N/A

MT2 POSITIVE

(Positive Half Cycle)

MT2 NEGATIVE

(Negative Half Cycle)

MT1

MT2

IGT

REF

QII

MT1

IGT

GATE

MT2

REF

MT1

MT2

REF

MT1

MT2

REF

QIV

QIII

ALL POLARITIES ARE REFERENCED TO MT1

(-)

IGT

GATE

(+)

IGT

GATE

(-)

IGT

GATE

(+)

NOTE: Alternistors will not operate in QIV

Thyristor Product Catalog Alternistor Triacs

Teccor Electronics http://www.teccor.com

+1 972-580-7777 4 - 7

** UL Recognized Product per UL File E71639.

Figure 4.1 Maximum Allowable Case Temperature vs On-State

Current (6-12 Amp Devices)

Figure 4.2 Maximum Allowable Case Temperature vs On-State

Current (8-12 Amp Devices)

Figure 4.3 Maximum Allowable Case Temperature vs On-State

Current (16 Amp Devices)

Figure 4.4 Maximum Allowable Case Temperature vs On-State

Current (25 and 40 Amp Devices)

THERMAL RESISTANCE (Steady State)

R θ JC [R θ JA] (TYP.) °C/W

Type

Isolated**

TO-218AC

FastPak**

TO-3BASE

Isolated**

THERMOTAB

TO-220AB

Non-Isolated

TO-220AB

Isolated**

TO-218X

6 amps 3.3 [50] 2.1 [45]

8 amps 2.8 1.8

10 amps 2.6 1.5

12 amps 2.3 1.4

16 amps 2.1 1.3

25 amps 1.35 1.3 2.0 1.1 1.32

40 amps 0.97 0.9 0.95

MT1 MT2 G

MT1

MT2

MT1 MT2 G

MT1 G

MT2

MT1

MT2

02468101214

100

110

120

130

RMS On-State Current [lT(RMS)] - AMPS

Maximum Allowable Case Temperature (TC) -

12 AMP TO-220 (ISOLATED)

10 AMP TO-220 (NON-ISOLATED)

6 AMP TO -220 (ISOLATED)

6 AMP TO-220

(NON-ISOLATED)

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 360˚

CASE TEMPERATURE: Measured as

shown on Dimensional Drawing

02468101214

100

110

120

130

RMS On-State Current [lT(RMS)] - AMPS

Maximum Allowable Case

Temperature (T

) - ˚C

12 AMP TO-220 (NON-ISOLATED)

10 AMP TO-220 (ISOLATED)

8 AMP TO-220 (ISOLATED)

8 AMP TO-220

(NON-ISOLATED)

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 360˚

CASE TEMPERATURE: Measured as

shown on Dimensional Drawing

100

110

120

130

0 5 10 15

RMS On-State Current [IT(RMS)] — Amps

Maximum Allowable

Case Temperature (TC)—˚C

16 AMP TO-220 (NON-ISOLATED)

16 AMP TO-220 (ISOLATED)

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTIVE ANGLE: 360˚

CASE TEMPERATURE: Measured as

shown on Dimensional Drawing

0 1020304050

100

110

120

130

RMS On-State Current [lT(RMS)] - AMPS

Maximum Allowable Case Temperature (TC) - ˚C

40 AMP FASTPAK &

TO-218 (ISOLATED)

25 AMP FASTPAK

TO-220 (NON-ISOLATED)

& TO-218 (ISOLATED)

25 AMP TO-220 (ISOLATED)

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 360˚

CASE TEMPERATURE: Measured as

shown on Dimensional Drawing

Alternistor Triacs Thyristor Product Catalog

http://www.teccor.com Teccor Electronics

4 - 8 +1 972-580-7777

Figure 4.5 On-State Current vs On-State Voltage (Typical)

(6-12 Amp Devices)

Figure 4.6 On-State Current vs On-State Voltage (Typical)

(16-40 Amp Devices)

Figure 4.7 Normalized DC Gate Trigger Voltage for all Quadrants vs

Case Temperature

Figure 4.8 Normalized DC Gate Trigger Current for all Quadrants vs

Case Temperature

Figure 4.9 Normalized DC Holding Current vs Case Temperature

Figure 4.10 Peak Surge Current vs Surge Current Duration

(6-12 Amp Devices)

0 0.6 0.8 1.0 1.2 1.4 1.6

Positive or Negative Instantaneous

On-State Voltage (vT)—Volts

Positive or Negative Instantaneous

On-State Current (iT)—Amps

= 25˚C

6 to 12 Amp Devices

00.6 0.8 1.0 1.2 1.4 1.6

Positive or Negative Instantaneous

On-State Current (iT)—Amps

16 AMP

TC = 25˚C

1.8

Positive or Negative Instantaneous On-State Voltage (vT)—Volts

40 AMP

25 AMP

1.0

1.5

2.0

-65 -15 +65+25 +125-40

Case Temperature (TC) — ˚C

VGT (TC=25˚C)

Ratio of VGT

1.0

2.0

3.0

4.0

-65 -15 +65+25 +125

-40

Case Temperature (TC) — ˚C

IGT (TC=25˚C)

Ratio of

IGT

1.0

2.0

3.0

4.0

-65 -15 +65+25 +125-40

Case Temperature (TC) — ˚C

IH (TC=25˚C)

Ratio of IH

INITIAL ON-STATE CURRENT

= 400mA (DC) 16-40A devices

= 100mA (DC) 6-12A devices

200

120

123456810 20 30 40 60 80 100 200 300 600 1000

100

Surge Current Duration — Full Cycles

Peak Surge (Non-Repetitive)

On-State Current (ITSM) — Amps

SUPPLY FREQUENCY: 60 Hz Sinusoidal

LOAD: Resistive

RMS ON-STATE CURRENT [IT(RMS)]: Maximum

Rated Value at Specified Case Temperature

NOTES:

1) GATE CONTROL MAY BE LOST

DURING AND IMMEDIATELY

FOLOWING SURGE CURRENT

INTERVAL.

2) OVERLOAD MAY NOT BE REPEATED

UNTIL JUNCTION TEMPERATURE

HAS RETURNED TO STEADY STATE

RATED VALUE.

10-12 Amp Device

6 Amp Device

8 Amp Device

Thyristor Product Catalog Alternistor Triacs

Teccor Electronics http://www.teccor.com

+1 972-580-7777 4 - 9

Figure 4.11 Peak Surge Current vs Surge Current Duration

(16-40 Amp Devices)

Figure 4.12 Turn-On Time vs Gate Trigger Current (Typical)

Figure 4.13 Power Dissipation (Typical) vs On-State Current

(6-12 Amp Devices)

Figure 4.14 Power Dissipation (Typical) vs On-State Current

(16 Amp Devices)

Figure 4.15 Power Dissipation (Typical) vs On-State Current

(25 and 40 Amp Devices)

Figure 4.16 Maximum Allowable Ambient Temperature vs On-State

Current

40 AMP

25 AMP

16 AMP

110

100 1000

100

250

300

400

1000

Surge Current Duration — Full Cycles

Peak Surge (Non-Repetitive)

On-State Current (ITSM)—Amps

200

1) GATE CONTROL MAY BE LOST

DURING AND IMMEDIATELY

FOLLOWING SURGE CURRENT

INTERVAL.

2) OVERLOAD MAY NOT BE

REPEATED UNTIL JUNCTION

TEMPERATURE HAS RETURNED

TO STEADY-STATE RATED VALUE.

SUPPLY FREQUENCY: 60Hz Sinusoidal

LOAD: Resistive

RMS ON-STATE CURRENT [IT(RMS)]: Maximum

Rated Value at Specified Case Temperature

NOTES:

0100 200 300 400 500

DC Gate Trigger Current (IGT)—mA

Devices with IGT = 80-100ma

Typical Turn-On

Time (tgt)—µSec

Devices with IGT = 20 - 35mA

Devices with IGT = 50mA

012345678910111213141516

RMS On-State Curren

t [lT(RMS)]—AMPS

Average On-State Power

Dissipation [PD(AV)]—Watts

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 360˚

6 - 12 AMP

0246810 12 14 16

RMS On-State Current [IT(RMS)] — Amps

Average On-State Power

Dissipation [P

(AV)]—Watts

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or inductive

CONDUCTION ANGLE: 360˚

16 AMP

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 360˚

012

20 28 36

416 24 32 40

RMS On-State Current [IT(RMS)]—Amps

Average On-State Power

Dissipation [PD(AV)]—Watts

40 AMP

25 AMP

120

100

0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0

TO-220 DEVICES

RMS On-State Current [IT (RMS)] — Amps

Maximum Allowable Ambient Temperature (TA) — ˚C

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 360˚

FREE AIR RATING – NO HEATSINK