F/DGX 12 P LF Characteristics Kennwerte Condition/Remark Bedingungen/Kommentar Value Wert_ Rated voltage Nennspannung Operating voltage Betriebsspannung V V 12 8...15 Rated current Nennstrom Note 1 (mA) 40 Coil resistance Spulen-Widerstand Coil impedance Spulen-Impedanz () Note 2 ( ) 140 12 240 Sound pressure level at 10cm distance Lautstarke in 10cm Abstand Note 1 (dB) 90 Resonant frequency Resonanzfrequenz ( Hz ) 2400 100 Operating temperature Betriebstemperatur ( C ) Storage temperature Lagertemperatur ( C ) -40...+85 -40...+85 Weight Gewicht 2 (g ) -----------------------------------------------------------------------------------------------------------------------------------------Note 1: Value applying rated voltage, frequency 2400 Hz, 1/2 duty square-wave mit angelegter Nennspannung, Rechtecksignal, Impulsverhaltnis 1 : 1 mit 2400Hz Note 2: Value applying 2400Hz, sine wave, measuring current 60 A. This value is for reference only. Sinusspannung 2400Hz, Mestrom 60 A. Dieser Wert ist nur fur Hinweiszwecke. Drawings Zeichnungen: Soldering condition Lotbedingung Wave soldering Schwalloten: Halbzeug, Werkstoff Untolerierte Mae Zeichn.-Nr. 100218.1B Mastab 2:1 Vervielfalt.-Pause Nr. gezeichnet Arbeitspause Nr. bearbeitet gepruft normgepr. Tag Name 118.02.10 KH And. And.-Mittlg. zust. Nr. Tag Ersatz f. Page Seite 1 of von 4 Zeichn. Name F/DGX 12 P LF FREQUENCY RESPONSE: TEST METHOD: 12 Halbzeug, Werkstoff Untolerierte Mae Zeichn.-Nr. 100218.1B Mastab 2:1 Vervielfalt.-Pause Nr. gezeichnet Arbeitspause Nr. bearbeitet gepruft normgepr. Tag Name 118.02.10 KH And. And.-Mittlg. zust. Nr. Tag Ersatz f. Page Seite 2 of von 4 Zeichn. Name F/DGX 12 P LF RELIABILTY TEST: VARIANCE AFTER TEST NO. ITEM TESTING CONDITION 1 Humidity 505, 93(+2/-3)%RH, 96HRS 2 High temp. +802, 96HRS 3 Low temp. -302, 96HRS Temperature Cycling -302, 30minutes room temp. 15 minutes +802, 30 minutes room temp. 15 minutes 5 cycles Drop test 3 times from height of 70cm onto the surface of 10mm thick wooden board. Vibration test Make the test for the directions of X Y and Z (total 0.5 hours). To-and-fro. sweep time (from 10 to 55 Hz and then from 55 to 10 Hz) under single amplitude of 1.0mm is 1 minute. 4 5 6 7 Solder heat resistance 8 Wave Soldering All specifications must be satisfied after the test. The part leads (pins) shall be immersed in molten solder maintained at 25010 for a period of 30 seconds. Halbzeug, Werkstoff Untolerierte Mae After the test part shall meet specifications without any degradation in appearance and performance. Zeichn.-Nr. 100218.1B Mastab 2:1 Vervielfalt.-Pause Nr. gezeichnet Arbeitspause Nr. bearbeitet gepruft normgepr. Tag Name 118.02.10 KH And. And.-Mittlg. zust. Nr. Tag Ersatz f. Page Seite 3 of von 4 Zeichn. Name F/DGX 12 P LF PACKING: NOTES: 1.100 PCS per box 2.Total 50 boxes per carton 3.Total 5000 PCS carton 4.Volume:51.5x42x26cm Halbzeug, Werkstoff Untolerierte Mae Zeichn.-Nr. 100218.1B Mastab 2:1 Vervielfalt.-Pause Nr. gezeichnet Arbeitspause Nr. bearbeitet gepruft normgepr. Tag Name 118.02.10 KH And. And.-Mittlg. zust. Nr. Tag Ersatz f. Page Seite 4 of von 4 Zeichn. Name F/DGX 12 P LF