FO-52847-F ? 3 | 4 5 | 6 | { | 8 y | () REV) DOCUMENT CHANGED BY CHECK | | 205839 |GRT I8JUNO2]| SAV OPERATING SPECIFICATION /\ /A\ LIMIT OPERATE /B\ | 542.09 | TARGET ENGAGEMENT .150 TO .300 RPM 0 TO 5000 RELEASE /&\ 3.0+2.5 |SLOT DEPTH .250 MIN NOTES | - MOUNTING SPECIFICATION: NON-FERROUS #4 MACHINE HEAD SCREWS WITH .25 0.D. WASHERS TORQUED TO 3-5 INCH LBS ELECTRICAL CHARACTERISTICS / SUGGESTED TARGET CONFIGURATION, MATERIAL: .045 LOW CARBON STEEL HIGH PERMEABILITY, LOW RESIDUAL INDUCTION CONDITION VAN OPERATE (DEGREES) IS THE ANGULAR DISTANCE FROM THE LEADING EDGE SPECIFIED VOLTAGE RANGE 3.8 TO 30 VDC OF THE TOOTH TO THE CENTERLINE ON THE SENSOR - v0 3 /\ RELEASE (DEGREES) |S THE ANGULAR DISTANCE FROM THE TRAILING EDGE MAX loff Vec=30V, Ts ink=20mh, =20 C<T<85 C, BPMAK OF [9.0 mA OF THE TOOTH TO THE CENTERLINE OF THE SENSOR MAX lon Vec=30V, Isink=20mA, -20 C<T<85 C, B>MAX OP 10.0 mA /\ OPERATING SPECIFICATION IS BASED ON TARGET SHOWN AND WILL VARY WITH RATED SINK CURRENT 20 mA TARGET GEOMETRY MAX Vsat Vee=3.8V, Isink=20mA, B>MAX OP 0.4 V MAX LEAKAGE CURRENT Vout=30V, Vccz24V, B<MIN REL 10 WA RISE TIME 10% TO 90% T=25C, Vec=l2V, R2=1.6 KQ, C2=20pf 1.5 us FALL TIME 90% TO 10% T=25C, Vec=l2V, R2=1.6 KQ, C2=20pf 1.5 uS ABSOLUTE MAXIMUM RATINGS TEMPERATURE -20C TO +85C 97 SUPPLY VOLTAGE (Vs) 13.8 VDC TO 30 VDC je 75 | VOLTAGE EXTERNALLY |-0.5 10 +30 VDC 2x D.125 | APPLIED TO OUTPUT OUTPUT CURRENT 50 mA ) .2 MAGNETIC FLUX NO LIMIT, CIRCUIT CANNOT BE DAMAGED oe BY MAGNETIC OVERDRIVE j f == {| t p RED (+) 26 AWG UL-1429 WIRE DIRECTION OF ROTATION ate (-) 26 AWG UL-1429 WIRE ~T 48.0+0.9 - GREEN (0) 26 AWG UL-1429 WIRE | I | | (R1.500) ) | (RI. 750 TARGET /A RELEASE /A\ : TRAILING EDGE OF TOOTH el be operate /\ \ LEADING EDGE C150) om OF mony (15) ~~ UNLESS OTHERWISE ine $1 (mm) RAWN SPECIFIED TOLERANCES ARE :Ctzleustoutny E**]actfre| ORT ISJUNO? NO PLACE x +.040 +1 |CHECK SAV | 8JUNO2 Honeywell ONE PLACE xX +030 40,4 SAaTN TWO PLACE XX +015 0. 15| THIS DRAWING COVERS A PROPRIETARY OY eugene A. THREE PLACE XXX 4.005 ITEM AND IS THE PROPERTY OF FTTTLE Do WOT OPEN of HANDLE ANGLES + + . VANE SENSOR- TT scoatait, tas RAW MATERIAL-COMMERCIAL STANDARD Mae PERMISSION OF HONEYWELL NSTLNITY: THIRD ANGLE PROJECTION STIEPDWG TYPE [DRAWING NAME REV DINENSIONS ARE T0 BE MET BEFORE [CS] | SRIGC-J8 1 Oc PROTECTIVE COATINGS ARE APPLIED 3D PTC ASME Y14.5M-1994 [SCALE 2 . | |WEIGHT SHEET | OF | ? 3 | ] 5 p | j 8 | 9 0